My old SonyEricsson Headset "HBH-35" work fine with my XDAII but it's battery gone weak thus I bought a New Headset HBH-300.
1. It bonded fine with my XDAII but when I turned off and turn on the HBH-300, there will be continue "Beeps" for almost 30 times (same tempo of green light blink) and after that it workable.
2. Sometimes when I hang-up the call with headset, there will be another "Beep" about 30 seconds after hang-up.
3. I also test with HBH-602 and HBH-660 and found the same problem but It works fine with my old and weak HBH-35.
4. My Old ROM was 1.60 / Radio 1.12 and New ROM is 2.06 / Radio 1.12 but still face the same problem.
5. Already tried new "Asia BT Patch" for XDAIIs but it kills my XDAII
Any Clue?
Related
I have bought a Plantronics M3000 bluetooth headset for my QTEK 2020. I have no problems pairing, calling and answering. However the headset just shuts off after a few minutes of conversation. It doesn't just cut the conversation but shuts off. I can make multiple short calls but nothing longer than 3/4 minutes. It works, however, without problems on my wife's Ericsson T68. Anyone can help ? Thanks.
Marek
Hello,
I have the MDA2 (same as QTek2020) and a Plantronics M3000 and It's been working just fine.
The problem you describe it's very weird since you mentioned that the headset works fine with your wife's mobile, and that makes me think that your QTek has some sort of problem with the Bluetooth stack or hardware.
It may be well worth to try (if possible) another headset just to make sure that is not the M3000 fault.
Do you see any type of error or message on the screen at the time of disconnection?
Does it always cut the conversation at the exact same moment?
Does the problem match the time the QTek takes to power save?
Any other clues?
Thanks.
I did not have the occasion to test another BT headset on the Qtek. When it shuts down there isn't any message displayed.
I have no problems with the BT stack (with the Pocket Bluetooth Tools patch) when using it with a BT GPS (Emtac) receiver, it works for hours.
However, your suggestion that it might happen when the Qtek goes in energy saving mode is interesting. I will check that tomorrow.
I'll post the result.
Hi
I seem to have a similar poblem after installing pocket bluetooth tools!.
I use a Jabra BT 250..and I noticed that the headset just mutes during the call..
I am generally used to switching off the display of the XDA after placing the call to power save ...
So I discovered that the headset would mute whenever i switch off the xda after making the call (which it never did prior to installing PBT)!
any thoughts on that?
maybe it has to do with the auto switch off plugin?
Actually I just experienced that too...
If I place (or answer a call) the next time I try to use the phone via the BT headset I notice the BT headset was turned off... Yeah, it could be related to the Powersave feature on the today plugin that PBT installs as a plugin... :roll:
Need to investigate...
Best regards,
Rayan
Both my bt headsets have stopped working since installing pocket bluetooth tools latest version, I have reverted back to version 1005 and everything is fine. I have a sony-ericsson EBH-65 and a skypower clip on headset.
my platronics does the same also its annoying you cant even transfer the call back to the device you have to hand up turn off bt and then turn it abck on and headset mode back on it also does the same on my pc
when im on msn using it as a headset it just d/c and i have to turn it off and turn it back on again
dont see what the problem is
btw the range on the xda2 and platronics is amazing i had it on my bedrooms desk and i went outside it passed through the living room wall and the patio window and i was stood 5m down my garden im sure it would of been over 10m and it was still working if i kept still when i moved it went crackly but ah well lol
just hope someone sorts the prob out
Hi,
I was having the same problem with the M3000. I just had confirmation from Plantronics that this problem is a bug in the product that occurs with the XDA II. I am currently in the process of returning the product.
Regards...Mike
Same problem M3000 doesn't work. Give up now before too much frustration makes you feel ill.
Try the Hello 2 headset. Work with my Aussie XDA2 and is very small and lightweight. Even had a neck chain to carry it around like a USB drive.
Help!
I have had my M3000 for about 8 months now and until recently it has worked fine.
Last week when I answered a call with it, the headset turned itself off after about 2 mins of talk time. The phone thought the headset was still connected and I had to transfer the call back to the phone, and end the call before I could do anything else. It is now doing this regularly.
I have re-bonded and the headset is fully charged (even tried it while connected to charger!)
I have also tried to run the headset against my pc (audio output) and this works fine.
The only thing I can think of is the battery in the 3000 losing its charge when connected to a phone, but when I charge it, it is ready in a matter of mins.
Anyone any other suggestions as to why the Headset powers itself off ?? Has anyone seen this behaviour before ??
Thanks in advance.
mine does the same mate its the platronics m3000 its crap and doesnt work well with the XDA2 use the bluetrek G2 they work great
Mine did the same, but I just noticed that the XDA2 was on Bluetooth Discoverable mode, when I switched to Bluetooth Connectable (On) it works fine
Thanks to all who have replied....
I have tried a few more things out :lol:
1) Logged an issue with Plantronics :wink:
2) Tried my BT Carkit which works no problem :lol:
3) Tried a Hard Reset - Works great afterwards :lol: until I install my apps
It has therefore got to be a problem with apps and rom version clash??
Those who have had similar issues with the Plantronics turning itself off after using it for more than about 1.5 Mins.... Do you have any of the following apps ???
Belkin IR Keyboard Drivers (Belkin WPDAK)
Fonix Voice Dial/ UK Roger
Microsoft Money
MTUX Ringtone X
Pocket Bluetooth Tools (1012)
RegKing
Sandisk WiFi
SBSH.NET Birth2Day/ Calendat Plus/ iLauncher
Scary Bears Check Notifi
Yishin Power Check
CDL - O2 Customisiation
Thanks,
Ian
Plantronics Bluetooth Headset
I also have the same problem. I also have a SanDisk wifi card (which on occasion also stops working causing me to hard reset) and Microsoft Voice Dialler and Pocket Breeze and a number of other plugins. The whole point of plug-ins is to use them! Any suggestions???
David
It gets worse!!
I have just tried the Widcomm stack on the XDAII.
Its probably me, but I just cant get the thing to pick up the headset when I make or recieve a call, so that was no use.
To uninstall Widcomm I had to do a hrad reset (Widcomm disables the sound after uninstallation for some reason - grrrr), and now the damm thing shows the same symptoms - even on a virgin hard reset device.
My only conclusion is that something changed in the last ROM to kill it. I'll wait for another ROM upgrade and see what happens then, but will now probably end up buying another headset.
Is anyone on 1.72 with a Plantronics that works??? :?:
Ian - Rom 1.72
Do you have the 1.72 Rom on the XDAII from the UK? I thought it wasn't out yet. Is it better than 1.60?
Re: Ian - Rom 1.72
pavid1 said:
Do you have the 1.72 Rom on the XDAII from the UK? I thought it wasn't out yet. Is it better than 1.60?
Click to expand...
Click to collapse
Yep 1.72 UK.
Its better than 1.6x but has still got issues with it - like needing to be hard reset every now and again (grrr). But BT is more stable and power drain is better.
My old SonyEricsson Headset "HBH-35" work fine with my XDA II but it's battery gone weak thus I bought a New Headset HBH-300.
1. It bonded fine with my XDA II but when I turned off and turn on the HBH-300, there will be continue "Beeps" for almost 30 times (same tempo of green light blink) and after that it workable.
2. Sometimes when I hang-up the call with headset, there will be another "Beep" about 30 seconds after hang-up.
3. I also test with HBH-602 and HBH-660 and found the same problem but It works fine with my old and weak HBH-35.
4. My Old ROM was 1.60 / Radio 1.12 and New ROM is 2.06 / Radio 1.12 but still face the same problem.
5. Already tried new "Asia BT Patch" for XDAIIs but it kills my XDA II
Any Clue?
I received my shiny new S710 today (replacing my imate sp5) i am having terrible problems with bluetooth and my car kit (Parrot Ck3100 with latest sortware) The phone connects and syncs ok but disconnects after a few mins and refuses to connect again.
I have an old motorola h605 headset that shows similar problems of not connecting or dropping the connection.
The Ck3100 kit has worked faultlessly with my imate sp5 for the last year.
Has anyone else had any problems with headsets or car kits?!
I have done a hard reset on the S710 and have nothing installed, and also disconnected the power to the CK3100 for 1/2 an hour before attempting to re setup the pairing
iain
Nokia CK7W
On a similar note, while my Vodafone V1415 works with my Nokia CK7W, I cannot end a call by pressing the button. Last number redial (two presses) and Hold or something like it (press and hold) are OK. To be fair, the CK7W is a little dated, but has proven to be fine with both Blue Angel and Hermes.
On the plus side the audio is good, without any echo for the remote caller.
Nokia CK-7W and S710
As with the Qtek 9100, the S710 seems not to operate soomthly with the NOKIA carkit CK-7w. I have to turn volume up to 100% and the sound from the speaker is still rather quite. The person i am calling is complaining that the line is not perfect. So for me it is back to the standard corded earpiece.
So any tips using the CK-7W and vox succesfully together are welcome!
@mcroonen
It's strange that I don't have the same experience as you. What version is your software? Compare with mine in my signature. I'm afraid I can't offer any suggestions, it seems to be pot luck! Maybe we find some variations in the radio stacks that will sort this out.
further to this i managed to borrow a e650 (vox) from work and it worked 100% with my car kit and tomtom and laptop!
I spoke to htc who said they had tested with the parrot ck3100 and said it worked 100%, as my phone was struggling to be detected by several devices and also struggling to detect other things that they recomended getting it replaced.
Spoke to handtech who said they would replace asap
jbn said:
@mcroonen
It's strange that I don't have the same experience as you. What version is your software? Compare with mine in my signature. I'm afraid I can't offer any suggestions, it seems to be pot luck! Maybe we find some variations in the radio stacks that will sort this out.
Click to expand...
Click to collapse
@jbn
KPN
OS: 5.2.1235 (Build 17740.0.2.0)
ROM: 1.15.405.2
Radio: 4.1.12.37_02.83.90
I had problems whith the sound quality and people not hearing me well.
For me it helped to delete the registry settings for the nokia ck-7w
It's under software/htc not sure if it was in LM or CU. I think LM.
Good luck
Had the same problem. Qtek8310 was working fine, S710 not. After a reset of the Parrot also the S710 is working fine.
aage said:
I had problems whith the sound quality and people not hearing me well.
For me it helped to delete the registry settings for the nokia ck-7w
It's under software/htc not sure if it was in LM or CU. I think LM.
Good luck
Click to expand...
Click to collapse
Unfortenately deleting the settings introduces echo and noise (voice sounds like robot). I think S710 and Nokis Ck-7w are not made for eachother.
I will try using the Parrot 3100 as on alternative BT solution..
Parrot CK3300 GPS CAR KIT
I have the Parrot CK3300 GPS CAR KIT and no problems at all with my S710, works a dream
Parrot
Hi,
You should visit http://www.parrot.com/uk/support/downloads
and get the latest software for your Parrot. You will need a bluetooth enabled laptop or to get your bluetooth enabled PC near your car!
Flash your parrot, then connect choosing a windows CE device. It will fully sync your phonebook too.
I use the Orange E650 and connect to my Holux GPS receiver and Parrot 3100 at the same time with no problems at all.
cheers
Sinet2020
JETware
See this thread for a possible solution for the Nokia CK7W!!!!
http://forum.xda-developers.com/showthread.php?t=331096
Hi All,
I just had a brand new Car with Bluetooth. (Citroen C4 Grande Picasso)
With this Bluetooth I should have the abbility to to connect, answer, and scroll trough the contacts, of my phone. I'm using a Wizard G3 with WM6 (Dutch) IPL/ SPL 3.08 and Radio: 1.08. (Radio will be updated soon)
Probelm is: stuff is not working! I can connect the phone to the car with Bluetooth and it is recognizing it. When I make a call or one comes in, the Car sees it and mutes the audio. But that's all. I do not hear anything and I can't be heard. Also the button (on the steering wheel) for contacts doesn't work; meaning: It says: there are no contacts.
Who experienced the same pproblems and more important who solved these?
Hi Jedeve,
I have the same problem with the same car. It worked for me when I first started TT and then automatically my bluetooth GPS mouse was connected and all was working fine. Strnage but true. It looks like if a channel is set open when connecting to the bluetooth GPS mouse and stay open so evrything is working. I also have looked into registry setting son bluetooth if I can find differences by using diff but no strange differences where found.
I also talked to the Citroen dealer and they told that it might be possible that new telephones with the newest software are not able to work correctly with the carkit.
I have a Wizard (I think a G3) with Octavoi 9.2 on it, IPL/ SPL 3.08 and Radio: 2.71.11.
Hi,
same car and same problem here.
It seems worked with WM5 and problem showed after upgrading to WM6.
Calling/answering from car controls ends with total silence most times.
I've noticed that if a call is answered from phone it works most times.
Also car phonebook seems support only latin characters and any contacts with non-latin ones(cyrillic in my case) do not appear on car.
Would appreciate any suggestions/solution to above problems.
Hi,
I have same problem, with same car! with TNT wm6 Roms!
With new TNT 6.1 did not try yet...
Now I have Slim wm6.1 ROM and no problem! With NTS wm6 rom not problem too... works fine!