So i have this program combined with this GPS aerial. However it would appear they have had a fight and will not communicate! Well to be honest i am unable to open a Com port according to the program...
This is from the site:
I think I know the correct port and speed, but trying to connect always yield's "Failed to open COM Port."
The access to a COM-port is mutual exclusive which means, that only one program may have access to the receiver at once.
If you are using TomTom, please try the following:
On the PocketPC, uninstall the TomTom ~GPS application (that and only that one)
Don't do it via the PC, do it on the PDA directly
The uninstall routine will ask for a soft reset. After that, everything (including TomTom) will work
Most probably another program or driver is blocking the port.
Click to expand...
Click to collapse
Now - this and Pocket Informant are the only 2 programs i ahve had running and also the only ones on my XDA after my Hard Resset last night
What is the problem and how do i fix it? Has anyone else had this issue - i have looked under their Success page for those with problems like mine but i cant find my combination or anyhting close
Also Oziexplorer was working with it up until i hard-resetted it so i know that the GPS works.
Com port
Had the same problem.
Disconnect the IR which is using the comport. Got to the connections setup and disable.
Directly after this has been done TomTom finds the GPS.
Rien
Absolute freaking legend...
Immediately after shutting the infrared off it switched on - it must block the com port from anything going in then...
So the big question remains - Why was Oziexplorer working with it?
Dopod M700
Same problem with my Dopod M700 + GPS Receiver + OziExplorer.
Where will we find another port to close it?
uncheck
"receive all incoming beams"
in network
My XDAII wont connect to GPS. I have tomtom5 installed on my xdaII and have tried a BT GPS receiver and a wired one. It will ask you the device type unpon installation and then the port number.
no i dea which port to use and have tried then all anyway. I get a message no device connected. I cannot keep my BT device connect when i pair it either. Tried this on a XDAIIs aswell and exactly same prob.
Please help!!
i would try unchecking "recieve all beam files" in connections
to release com1
and try once more
Turn off beams releases com 1 for the wired gps. I think wired gps is the way to go if you need it for incar use only, I see far too many problems with bluetooth and if you have no sense of direction like me it is very annoying when the bluetooth decides to start acting stupid.
i will try
thanks guys im away from home till wknd so i will try this when i get back.
i will let you know if it works.
thanks
Yup that worked great thanks guys
Have just installed WM6 (JW 2.02.02 WWE) and everything appears to be fine except for the BT com port in TomTom Nav5. Have paired the BT GPS, set the outgoing port (COM0) but it doesn't appear in the list of ports available in TomTom.
Is this a known issue or have I got to set something else? Have also tried the External GPS manager in 'Settings' but that port doesn't show either.
Sheepdip said:
Have just installed WM6 (JW 2.02.02 WWE) and everything appears to be fine except for the BT com port in TomTom Nav5. Have paired the BT GPS, set the outgoing port (COM0) but it doesn't appear in the list of ports available in TomTom.
Is this a known issue or have I got to set something else? Have also tried the External GPS manager in 'Settings' but that port doesn't show either.
Click to expand...
Click to collapse
I've had the same problem.
What I've done about this, is I've added a Serial port profile for the GPS device. Then went into TomTom and the port was in the list. This port has worked fine.
Tried setting External GPS in the Settings/Connections, to share it, well - TOUGH, does not work.
So I have a working TomTom and I gave up for now about the sharing stuff...
Try setting port 8.
I'm not interested in sharing it (at the moment).
Can you explain what you mean by 'added a serial port profile'?
I've set up an outgoing com port in settings > bluetooth > COM ports but it's not seen by TomTom
tyl said:
Try setting port 8.
Click to expand...
Click to collapse
I must have tried all the ports that were available but none of them show. All I get is the standard TomTom list: -
QCT Data Interface
Serial Cable on COM1
COM7
RIL on COM6
Infrared Port
Ir on COM3
and of course non of those work either.
Sheepdip said:
I must have tried all the ports that were available but none of them show. All I get is the standard TomTom list: -
QCT Data Interface
Serial Cable on COM1
COM7
RIL on COM6
Infrared Port
Ir on COM3
and of course non of those work either.
Click to expand...
Click to collapse
Exactly where you wrote it, in COM ports.
Then I've selected "Other Bluetooth GPS receiver" as receiver type in TomTom 6, and here's what I have:
COM5:
QCT Data Interface
Serial Cable on COM1:
COM7:
RIL on COM6:
Infrared Port
Ir on COM3:
COM4:
COM5 is my attempt to share GPS which is failing so far, so disregard it for here (but I'll try COM8 later). COM4 is the Outgoing Bluetooth port and that's the one I selected.
I must admit that I honestly don't understand why this setup works for me. I expected to put Incoming port number (a common for all devices) there, but obviously didn't have it.
Hmmm, that's strange. What you have is exactly what I used to get in WM5 but it doesn't seem to work in WM6? I'm also on TT5 so that may be an issue?
From what I can see, the 'QTC Data Interface' is the GPS sharing port and is actually COM9, installed by the OS. But it doesn't work!
Frustrating............!
I'm also getting tons of memory leak by the looks of it.
SORTED!
Feel a bit stoopid. Checked the version of TT5 and it showed 5.0. Upgraded to 5.21 (which is what I thought I installed) and bingo! Com port shows and works.
Thanks to all who made suggestions.
Sheepdip said:
Feel a bit stoopid. Checked the version of TT5 and it showed 5.0. Upgraded to 5.21 (which is what I thought I installed) and bingo! Com port shows and works.
Thanks to all who made suggestions.
Click to expand...
Click to collapse
Man, my TomTom is version 6.010.
Just in case, it's available.
put in External GPS the program port on 8.
then you will see com 8 in TomTom.
connect it in TomTom and after that change the program port back to none and hardware port on 8.
problem solved.
I've had this problem on a Mini S, Exec, Vario II.
Some times just removing TomTom and re-installing it seems to work. On several occasions the correct COM port shows up in TomTom. I honestly don't know why. It seems a bit random.
Airax said:
I've had this problem on a Mini S, Exec, Vario II.
Some times just removing TomTom and re-installing it seems to work. On several occasions the correct COM port shows up in TomTom. I honestly don't know why. It seems a bit random.
Click to expand...
Click to collapse
I have seen some recommendation to not select Bluetooth receiver. I don't know, I thought it would be un-cool So I made it work with Bluetooth receiver.
EastExpert said:
Man, my TomTom is version 6.010.
Just in case, it's available.
Click to expand...
Click to collapse
I know, but the old TT5 maps won't work with 6 and I've got quite a few that don't come with the Europe disk.
solution to tt gps connection problems
hi everyone with this problem,
no matter what your setup is vario, xda, dell, tt5 or tt6, tomtom gps or other GPS try this method (it does bloody work) :
STEP 1 : INSTALL TOMTOM5 OR TT6
You do this by copying the CAB files from the CDROM using JasJar or using SD card o any other way
STEP 2 : UPGRADE (THIS IS NOT ESSENTIAL, ONLY DO IT IF YOU HAVE A NON-HOKY COPY OF TT)
http://www.htcclub.net/storage/ppcupd510.rar
or just overwrite patched version of main executable file over original
also having this install on some vario 2 may also help BTHTools1100.
STEP 3 : ACTIVATE THE GPS CONTROL PANEL
this is hidden option but if you use this wisely you will take control over your GPS but in many cases this is reson why tt sometimes works sometimes doesn't.
Fire up a registry editor (eg http://www.freewareppc.com/utilities/phmregistryeditor.shtml )
Go to: HKEY_LOCAL_MASCHINE\ControlPanel\GPS Settings
Delete the DWORD marked "hide"
Add a DWORD called "Group" and give it the value of "2" (dec)
The GPS panel will now show up in your connection settings.
STEP 4 : INSTALL TOMTOM
1. Establish a bond with your GPS and select the checkbox for serial access.
2. In BT, select the OUTGOING port to 8. (optional: make it non secure if available)
3. In the GPS control panel, select the GPS program to 0 and make sure that the hardware one, is set to None, also you should pay attention to 3 tab and allow windows to manage it - for now, you don't really want Bill managing things as it is recipe for disaster.
4. Start TT and the GPS settings, select another bluetooth GPS, and you will see COM 0 free. Select COM 0 and close TT5. (if you don't get the port go back one step and check 3 tab)
5. At the GPS control panel again, now select COM 8 (before we set it up at 0).
6. At BT: select OUTGOING port to 0.
7. Back again to GPS control panel and select NONE.(and now is the right time untick 3 tab option and stop auto managing)
8. Finally start TT and it should connect automatically. Wait for a couple of seconds and click the GPS settings and you should see it has connected.
Congratulations
well, in case something didn't go well start from scratch - reset your software restore your registry and reinstall as much as you can get back to factory defaults using hard reset and etc.
I know this is is in bits available elsewhere but this is more complete and little bit more up to date, but there is still hundreds of people looking for this.
THE SUMMARY
I've spent many many days looking for solutions, registry and web and all sort of tools to solve this, but this method works the treat - and it does make perfect sense - I suspect the reason why this is such a problem is timeout. windows is not a good platform - and it is locked by ms and all sorts of legacy issues. Obvious reason is tt doesn't load quickly enough and and detecting correct port seem to an issue so if you follow instruction you will see that sulotion is guiding your software to speak with 3party hardware having windows in the middle
good luck
Paulius - Excellent instructions and they work just great.
However....For me it only works one time. By that I mean after I turn everything off and then want to use it another time - it again cannot see the GPS device - and I have to do all of the above again.
Do you know why the settings are not retained? Note; I have unticked the the stop auto managing option already.
Hope you can assist.
Paulius - Excellent instructions and they worked fine but only the first time unfortunately for me.
i.e the next time I want to use tomtom - i have to go through all of the above again as it cannot find the GPS again.
Have you come across this before. Note: I have done exactly everything you have instructed above
Tomtom loses GPS settings
Paulius - Excellent instructions and they worked fine but only the first time unfortunately for me.
i.e the next time I want to use tomtom - i have to go through all of the above again as it cannot find the GPS again.
Have you come across this before. Note: I have done exactly everything you have instructed above
I had the same problem.
Luckily I had a backup of my TomTom installation.
It all comes up to the navigator.cfg file inside the Navigator folder. I copied the old one over and did not enter TomTom's GPS Setup menu anymore.
All I did after flashing was to just pair my BT GPS receiver and start TomTom. One needs to wait 5 seconds or so after the main screen opens, until the GPS is found. Do not try to select the receiver in the settings menu!
This happend on both my devices (BA and UNIVERSAL) after installing a WM6 firmware WITH the GPS Manager in the Settings.
Cheers,
vma
Thanks VMA - I understand.
Did you setup an outgoing port though in Bluetooth?
reply to nsm
hi nsm, sorry it took this long to respond, I didn't know the solution to your problem.
However, after few gliches with my pda's I think I can add to the list of thing to go wrong.
First is WM itself sometimes causes problems - so before you do anything else turn it of and on again - it did happen to me in the middle of london and I come from Lithuania well, it can be good fun navigating through canary warf without gps - aim for tall buildings :-D or away from them.
Second is once you followed my original instruction do not go back to gps settings menu, because after this you will have to start again from begining.
Third - is do allow minute or few for gps to lock onto satellites - especially if you are in doors or between buildings. Once in Crete it was quite hard to find satellite signal because of a mountains and I had clear sky view to one direction - but as you drive especially bigger cars, metal body will block signal.
Fullproof recipe is to have two units, if possible for one of them use bluetooth separate gps module as this will allow you to place both gps unit and pda screen in ideal locations for satellite signal and driver.
Fourth - this is boring and can take a lot of time, but may resolve lots of weird issues. Follow my instructions and then you set your tomtom to use data transfer baud rate 4800, 9600 and etc do try all the options - from low to high rate, this means that every time you'll have to start again instructions from beginning. TT6 on some of my pda's prefers 56700, tt5 - 4800 and so on. give this some time explore all the settings.
And finally if you have stability issues check your pda memory limits - try not to push it to 90%+ on unit or memory car, best is to leave plenty on both, this may cause settings not to be saved and all sorts of bugs.
the practical advice is to keep selling and buying pdas till you find one which will do the job for you, Try ebay , but do check descriptions and guides and most important sellers rating! All pda, mda and nokia simbion phones I tried with enough effort will work but many many of them have issues with stability or are difficult to setup.
Hope this helps.
Good luck
ok so i bought an att fuse and like everyone here mentioned about hang ups, weak signal, etc i thought i would just use my old external bluetooth gps unit.
so breifly here is the problem, it works fine when i use a single application like google maps. but when i try to put the information in the external gps app (start>settings>external gps) i have my problem.
under the hardware section, it states:
Specify the hardware port to which your GPS device is connected.
i do so click ok and nothing.. so i go back in to see whats wrong and the gps hardware port resets its self to "none". its as if the settings never save or reset them selves. i know on my old phone (tytn) this would be somthing i considered unusual (so i am kinda familar with the mobile) os.
i am not sure if there is somthing wrong with my handheld or if at&t has some kind of block?
anyway i tried to use the forum search and really didnt turn up any information so any help would be great i really like this phone.
thanks in advance to anyone that can help.
I've never had those settings stick on any of my WinMo phones.
You don't need to use that to use a BT GPS puck anyway, you set the COM port in the Bluetooth settings.
It won't let you make a selection from that drop-down because the GPS hardware does not function by exposing a COM port as with standard hardware, it exposes a GPS0: port, that is picked up by the GPS ID, and exposed to the system as COM4:..
Now because the GPSID has been replaced by HTC's version of it, it's designed to work only with their internal GPS. If you want support for an external GPS in the GPS ID, you need to cook the stock Windows Mobile driver back into the ROM..
That being said, you don't need the GPSID unless you plan to have multiple programs connecting to the GPS at once, so you should be able to squeek by..
thanks guys i knew i would get a respoce here. unfortunatly i was hoping for a easy solution to use external gps with multiple apps i see unfortunatly its not possible without alot of work.
at any rate i am still very hapy with the device i was debating on upgrading from the tytn amd so glad i did =)
Hello everyone. I have an iPAQ 210 and a CF GlobalSat BC-337 GPS card. It has always worked without a hitch until now. It could be because I installed some GPS emulation software that worked on wifi triangulation (more like it didn't work) and I'm guessing maybe it stole the com port that my card was using but that's just a theory. In any case, now my GPS doesn't work.
The ppc software that came with the card (used for running diagnostics) still detects the card on COM 1 and runs the card just fine to check sattelite strength, etc. so I know the card works and is capable of communicating through the com port. However, the windows CE 6.0 settings "external gps" normally asks for a software port and a hardware port. Both were set before but now the hardware port has reset to "none" and nothing I do to change it will stick. When I put it on COM 1 and press ok and go back in it still says "none". None of my mapping software will work either in manual mode or in "let windows manage it" mode....but as I said, the gps software sees and runs the card so I suspect windows settings are to blame. Anyone have an idea how to fix this? Is there a registry key I can change or something? Thank you.