Related
Hey Guys -
I have had my A9 for about 2 months and love it. When I first purchased it, I rooted it using the method pinned to this forum which seemed to work well. Soon afterwards, I found out that when I inserted and tried to format an SD card as "internal", it wouldn't work and result in it showing as "corrupted." I soon found out that this seemed to be due to the root replacing the original boot.img which messes with encryption. Since the root was posted, SuperSU has been updated and that step has changed supposedly.
Now that I have some time, I want to fix this issue. Before doing so, I've read through many posts and think I have a plan. I wanted to post the steps I need to follow as I understood them to make sure my plan is correct and will result in not only being able to format an SD internally and be rooted, but also a working phone Below are the specs of my phone, the steps I think it may take to resolve, and a few questions I have after reading through numerous posts. Any help is appreciated!
Phone Specs
Some as currently listed in Settings
- HTC One A9
- AT&T USA
- Rooted / s-off
- Android 6.0 / Sense 7.0g
Software Number: 1.10.502.3
Kernel: 3.10.73-perf-g28d66e0
Baseband: [email protected]_29.05_F
Build: 1.10.502.3 CL635081 release keys
Android Security Patch Level: 2015-10-01
Steps to Fix
1. Backup any data desired (I have a nightly Titanium backup)
2. Download RUU for same version (1.10.502.3) from http://forum.xda-developers.com/one-a9/general/wip-ruu-htc-one-a9-t3240344
Should I use newer version or are those for different carriers?
3. Apply RUU (via embedded EXE or try to extract and apply using adb/fastboot)
4. Once phone is restored, make a backup of boot.img from phone just in case it's needed later
5. Install TWRP via adb/fastboot
6. Install SuperSU via TWRP
At this point (if I can make it to this point), test and see if the phone's rooted and I can format the SD internally. If so, great. If not, continue with the following steps...
7. Download & flash modded boot.img from A9 Root post
8. Install TWRP via adb / fastboot
9. Install SuperSU via TWRP
10. Flash original boot.img backed up in step #4 to my phone (since modded one was only needed initially to install SuperSU) So that encryption keys match and I may successfully format sd cards for internal use
My Questions
1. Are the steps above basically the process i need to perform or is there a better / easier way? I don't know if I could flash a common boot.img from an RUU or if it needs to be flashed to phone first for encryption purposes. Even if I can, I've tried to extract it from ruu.zip before and could not
2. Should I use an RUU for a newer version (over 1.10.502.3) or are those for different carriers and not work with my AT&T phone?
3. Does it make a difference if I install the RUU via embedded EXE or extract and apply using adb/fastboot?
4. What versions of TWRP & SuperSU should I use?
Any additional suggestions would be appreciated - I just want to get this resolved once and for all! - Thanks!
bzowk said:
Hey Guys -
I have had my A9 for about 2 months and love it. When I first purchased it, I rooted it using the method pinned to this forum which seemed to work well. Soon afterwards, I found out that when I inserted and tried to format an SD card as "internal", it wouldn't work and result in it showing as "corrupted." I soon found out that this seemed to be due to the root replacing the original boot.img which messes with encryption. Since the root was posted, SuperSU has been updated and that step has changed supposedly.
Now that I have some time, I want to fix this issue. Before doing so, I've read through many posts and think I have a plan. I wanted to post the steps I need to follow as I understood them to make sure my plan is correct and will result in not only being able to format an SD internally and be rooted, but also a working phone Below are the specs of my phone, the steps I think it may take to resolve, and a few questions I have after reading through numerous posts. Any help is appreciated!
Phone Specs
Some as currently listed in Settings
- HTC One A9
- AT&T USA
- Rooted / s-off
- Android 6.0 / Sense 7.0g
Software Number: 1.10.502.3
Kernel: 3.10.73-perf-g28d66e0
Baseband: [email protected]_29.05_F
Build: 1.10.502.3 CL635081 release keys
Android Security Patch Level: 2015-10-01
Steps to Fix
1. Backup any data desired (I have a nightly Titanium backup)
2. Download RUU for same version (1.10.502.3) from http://forum.xda-developers.com/one-a9/general/wip-ruu-htc-one-a9-t3240344
Should I use newer version or are those for different carriers?
3. Apply RUU (via embedded EXE or try to extract and apply using adb/fastboot)
4. Once phone is restored, make a backup of boot.img from phone just in case it's needed later
5. Install TWRP via adb/fastboot
6. Install SuperSU via TWRP
At this point (if I can make it to this point), test and see if the phone's rooted and I can format the SD internally. If so, great. If not, continue with the following steps...
7. Download & flash modded boot.img from A9 Root post
8. Install TWRP via adb / fastboot
9. Install SuperSU via TWRP
10. Flash original boot.img backed up in step #4 to my phone (since modded one was only needed initially to install SuperSU) So that encryption keys match and I may successfully format sd cards for internal use
My Questions
1. Are the steps above basically the process i need to perform or is there a better / easier way? I don't know if I could flash a common boot.img from an RUU or if it needs to be flashed to phone first for encryption purposes. Even if I can, I've tried to extract it from ruu.zip before and could not
2. Should I use an RUU for a newer version (over 1.10.502.3) or are those for different carriers and not work with my AT&T phone?
3. Does it make a difference if I install the RUU via embedded EXE or extract and apply using adb/fastboot?
4. What versions of TWRP & SuperSU should I use?
Any additional suggestions would be appreciated - I just want to get this resolved once and for all! - Thanks!
Click to expand...
Click to collapse
First off, this isn't Development.
Secondly, I explained to you how to fix this in the very root thread you linked several times.
Thirdly, there's a newer, official RUU from HTC right on their ROM Downloads website. I'd start by installing that (though I also have a recovery-flashable version of that ROM in my Base ROM thread).
Fourthly, with access to an official RUU, and my ROM decrypt script, you have access to the stock boot.img (which is also in the firmware zip in my Base ROM thread), which you can use as your baseline for restoring the verity key to the ramdisk, thereby allowing you to use adopted storage without any issues. Note however that I was only able to use adopted storage with the "forceencrypt" flag enabled.
Fifthly, you can't just restore the stock boot image (at least not if you want to stay rooted). You can be both rooted and encrypted, but you have to first make sure SuperSU is flashed and set up prior to allowing the device to be encrypted again (adopted storage only works with an encrypted device, and then you won't be able to access your storage with TWRP).
OK, OK - sorry.... It had been a while since posting and honestly forgot about that thread - my fault.
I decided to start fresh so have already restored the phone to HTC's latest RUU (1.27.502.5 ATT) as I already had it downloaded. I've also flashed TWRP 2.8.8.1 to the phone, but am obviously prompted to enter a password when I try to enter recovery. Based off what I've read, the steps below seem to be what I need to do so that I may be rooted + still have encryption for internal sd formatting. Is it correct (or close to it)
Using an Ubuntu 14.04 x86 VM...
1. Download & extract your decrypt script to a temp folder in linux vm
2. In Windows, run same RUU I applied and copy out rom.zip from %temp%
3. Rename "rom.zip" to "rom_a9.zip"
4. Copy rom_a9.zip to the ""place_rom_zip_here" folder of your extracted script in the vm
5. Run ./decrypt-htc and wait for script to complete to get img files
On Phone (Currently has same RUU installed + TWRP but not rooted)
6. Root phone using original method of flashing modded boot.img, install SuperSU, and get rooted
7. Once done and rooted, flash boot.img I extracted using your script above to phone via adb
Once that's done, it should be rooted + have encryption thus allowing me to use internal sd card, right? Sorry to be such a bother - just want to get this fixed and done with
Thanks!
bzowk said:
OK, OK - sorry.... It had been a while since posting and honestly forgot about that thread - my fault.
I decided to start fresh so have already restored the phone to HTC's latest RUU (1.27.502.5 ATT) as I already had it downloaded. I've also flashed TWRP 2.8.8.1 to the phone, but am obviously prompted to enter a password when I try to enter recovery. Based off what I've read, the steps below seem to be what I need to do so that I may be rooted + still have encryption for internal sd formatting. Is it correct (or close to it)
Using an Ubuntu 14.04 x86 VM...
1. Download & extract your decrypt script to a temp folder in linux vm
2. In Windows, run same RUU I applied and copy out rom.zip from %temp%
3. Rename "rom.zip" to "rom_a9.zip"
4. Copy rom_a9.zip to the ""place_rom_zip_here" folder of your extracted script in the vm
5. Run ./decrypt-htc and wait for script to complete to get img files
On Phone (Currently has same RUU installed + TWRP but not rooted)
6. Root phone using original method of flashing modded boot.img, install SuperSU, and get rooted
7. Once done and rooted, flash boot.img I extracted using your script above to phone via adb
Once that's done, it should be rooted + have encryption thus allowing me to use internal sd card, right? Sorry to be such a bother - just want to get this fixed and done with
Thanks!
Click to expand...
Click to collapse
Re-read my post. If you flash the stock boot.img, you will no longer be rooted.
And as I said in the original thread, you need to pull the rooted boot.img and add the verity key from the stock one to it. Also you'll need to add the forceencrypt and verify flag back.
P.S. You also need to re-read the instructions in the decrypt thread. You don't have to rename anything anymore.
Good Afternoon -
OK - sorry to frustrate you, but I think I finally have it figured out. I started from scratch, re-read many posts, and took notes. I was a little confused on the last part so wanted to verify, please...
I've already unpacked the boot.img from the latest HTC A9 (AT&T) RUU and have the two folders. I restored the same RUU to my phone, flashed TWRP 2.8.8.1, backed up the boot.img, and unpacked it before realizing that I should have probably rooted it first.
Correct me if I'm wrong, but here's all I need to do to finish....
1. Download modified A9 boot.img from top of root thread
2. Flash modded boot.img using fastboot
3. Verify TWRP is still installed then use it to install SuperSU 2.67 (latest)
4. Back up boot partition just like I did before in TWRP
5. Unpack it on PC to create ramdisk and split_img folders
6. Copy verity_key from unpack of the actual RUU and overwrite one in rooted unpack
7. Edit the file fstab.qcom in the ramdisk folder of the rooted unpack in Notepad++ and add the "verify" flag after the wait flag on the fist uncommented line - save
8. Repack rooted boot.img
9. Flash phone with repacked boot.img using fastboot
10. Reboot & enjoy a rooted phone + encryption allowing sd internal formatting
Promise not to bug anymore if I can just get this resolved.
Thanks again for your assistance!
UPDATE
Hmm - was just prepping and went to download modded file from root thread's first post. Doesn't seem to have one that matches newest build of RUU I flashed - if I'm interpreting it correctly. Researching further, but if know of alternate method or another solution to get through steps 1 & 2 about (assuming they are correct), I'd appreciate it. Thanks
bzowk said:
Good Afternoon -
OK - sorry to frustrate you, but I think I finally have it figured out. I started from scratch, re-read many posts, and took notes. I was a little confused on the last part so wanted to verify, please...
I've already unpacked the boot.img from the latest HTC A9 (AT&T) RUU and have the two folders. I restored the same RUU to my phone, flashed TWRP 2.8.8.1, backed up the boot.img, and unpacked it before realizing that I should have probably rooted it first.
Correct me if I'm wrong, but here's all I need to do to finish....
1. Download modified A9 boot.img from top of root thread
2. Flash modded boot.img using fastboot
3. Verify TWRP is still installed then use it to install SuperSU 2.67 (latest)
4. Back up boot partition just like I did before in TWRP
5. Unpack it on PC to create ramdisk and split_img folders
6. Copy verity_key from unpack of the actual RUU and overwrite one in rooted unpack
7. Edit the file fstab.qcom in the ramdisk folder of the rooted unpack in Notepad++ and add the "verify" flag after the wait flag on the fist uncommented line - save
8. Repack rooted boot.img
9. Flash phone with repacked boot.img using fastboot
10. Reboot & enjoy a rooted phone + encryption allowing sd internal formatting
Promise not to bug anymore if I can just get this resolved.
Thanks again for your assistance!
UPDATE
Hmm - was just prepping and went to download modded file from root thread's first post. Doesn't seem to have one that matches newest build of RUU I flashed - if I'm interpreting it correctly. Researching further, but if know of alternate method or another solution to get through steps 1 & 2 about (assuming they are correct), I'd appreciate it. Thanks
Click to expand...
Click to collapse
You don't need anything from that root thread. Everything there is deprecated (which I've said several times).
If you already have the stock boot.img unpacked and ready to go, all you have to do is flash SuperSU, then back up the rooted boot.img that you now have on your device thanks to SuperSU. Unpack that boot.emmc.win and add the verity_key from the stock ramdisk and replace the fstab.qcom with the one from the stock ramdisk. Repack, flash to your device via fastboot or TWRP, and your device will encrypt on that first boot and you'll be good to go.
Just to make sure - you did a Format Data in TWRP prior to flashing SuperSU, correct?
Captain_Throwback said:
You don't need anything from that root thread. Everything there is deprecated (which I've said several times).
If you already have the stock boot.img unpacked and ready to go, all you have to do is flash SuperSU, then back up the rooted boot.img that you now have on your device thanks to SuperSU. Unpack that boot.emmc.win and add the verity_key from the stock ramdisk and replace the fstab.qcom with the one from the stock ramdisk. Repack, flash to your device via fastboot or TWRP, and your device will encrypt on that first boot and you'll be good to go.
Just to make sure - you did a Format Data in TWRP prior to flashing SuperSU, correct?
Click to expand...
Click to collapse
Thanks -
Well, that's the thing... One of the two unpacked boot.img I have currently is wrong. The two I have are:
- One unpacked boot.img extracted from latest RUU using your script in linux
- One unpacked boot.img backed up from unrooted phone which only had TWRP flashed
That was part of my question. I know that the 2nd unpacked boot.img above is worthless as the phone needed to be rooted prior to me backing it up. The question for me is how to flash superSU onto the phone (which currently has the same latest RUU + TWRP 2.8.8.1 installed) if I can only access TWRP is a read-only mode as I'm prompted for password upon booting to recovery. That's why I brought up the legacy root method as I don't know of an alternative... unless SuperSU doesn't require write permissions to whatever TWRP has locked down currently.
Once I can root it, backup it's boot, and unpack it; I just need to literally copy & overwrite the "verity_key" and "fstab.qcom" files (assuming the only difference is the fstab.qcom I'm overwriting doesn't have the verify flag), repack, then flash back to phone via fastboot, right?
Thanks for your patience!
bzowk said:
Thanks -
Well, that's the thing... One of the two unpacked boot.img I have currently is wrong. The two I have are:
- One unpacked boot.img extracted from latest RUU using your script in linux
- One unpacked boot.img backed up from unrooted phone which only had TWRP flashed
That was part of my question. I know that the 2nd unpacked boot.img above is worthless as the phone needed to be rooted prior to me backing it up. The question for me is how to flash superSU onto the phone (which currently has the same latest RUU + TWRP 2.8.8.1 installed) if I can only access TWRP is a read-only mode as I'm prompted for password upon booting to recovery. That's why I brought up the legacy root method as I don't know of an alternative... unless SuperSU doesn't require write permissions to whatever TWRP has locked down currently.
Once I can root it, backup it's boot, and unpack it; I just need to literally copy & overwrite the "verity_key" and "fstab.qcom" files (assuming the only difference is the fstab.qcom I'm overwriting doesn't have the verify flag), repack, then flash back to phone via fastboot, right?
Thanks for your patience!
Click to expand...
Click to collapse
Once you Format Data in TWRP and reboot recovery, you can flash SuperSU and you will be rooted. You just have to back up the boot.img after flashing SuperSU on the unencrypted device to re-enable verity so that adopted storage will work.
P.S. And no, the verify flag isn't the only difference. As I also said earlier (I'm constantly repeating myself), the device must be encrypted for Adopted Storage to work, so the forceencrypt flag from the stock fstab must also be present. That's why it's easier just to replace the whole file. The problem you have at the end of the day is that, while you'll be rooted and be able to use adopted storage in Android, you still won't be able to access said storage (or /data) in TWRP.
Captain_Throwback said:
Once you Format Data in TWRP and reboot recovery, you can flash SuperSU and you will be rooted. You just have to back up the boot.img after flashing SuperSU on the unencrypted device to re-enable verity so that adopted storage will work.
P.S. And no, the verify flag isn't the only difference. As I also said earlier (I'm constantly repeating myself), the device must be encrypted for Adopted Storage to work, so the forceencrypt flag from the stock fstab must also be present. That's why it's easier just to replace the whole file. The problem you have at the end of the day is that, while you'll be rooted and be able to use adopted storage in Android, you still won't be able to access said storage (or /data) in TWRP.
Click to expand...
Click to collapse
Great - Thanks!!
Just to make sure, below's my plan with a small question @ step #5. Does it get your stamp of approval?
Phone (A9) already had latest RUU restored (same RUU I ran against your script to pull boot.img from) and TWRP 2.8.8.1 flashed
1. Boot into TWRP & bypass initial screen prompting for password
2. Format Data
3. Reboot back into TWRP
4. Flash SuperSU 2.76 zip
5. Reboot to system then back to TWRP and backup boot partition? / Stay in TWRP and backup boot partition? / Reboot back into TWRP and backup boot partition?
6. Unpack backed up boot partition from phone
7. Copy "verity_key" & "fstab.qcom" files from ramdisk folder in unpacked RUU boot and paste into & overwrite same files in ramdisk folder of unpacked boot from rooted phone
8. Repack rooted phone boot (which includes both new files)
9. Flash newly packed boot.img to phone using fastboot
10. Enjoy
I really appreciate your help and patience with me!
bzowk said:
Great - Thanks!!
Just to make sure, below's my plan with a small question @ step #5. Does it get your stamp of approval?
Phone (A9) already had latest RUU restored (same RUU I ran against your script to pull boot.img from) and TWRP 2.8.8.1 flashed
1. Boot into TWRP & bypass initial screen prompting for password
2. Format Data
3. Reboot back into TWRP
Click to expand...
Click to collapse
Good so far . . .
bzowk said:
4. Flash SuperSU 2.76 zip
Click to expand...
Click to collapse
I'm sure this is just a typo, but that should be 2.67, not 76 (there is no 2.76).
bzowk said:
5. Reboot to system then back to TWRP and backup boot partition? / Stay in TWRP and backup boot partition? / Reboot back into TWRP and backup boot partition?
Click to expand...
Click to collapse
Bolded the correct one above (no need to leave TWRP as the necessary modifications have already been made).
bzowk said:
6. Unpack backed up boot partition from phone
7. Copy "verity_key" & "fstab.qcom" files from ramdisk folder in unpacked RUU boot and paste into & overwrite same files in ramdisk folder of unpacked boot from rooted phone
8. Repack rooted phone boot (which includes both new files)
Click to expand...
Click to collapse
Looks good . . .
bzowk said:
9. Flash newly packed boot.img to phone using fastboot
Click to expand...
Click to collapse
TWRP can also flash the new image, but fastboot is probably the most reliable way to do it.
bzowk said:
10. Enjoy
Click to expand...
Click to collapse
Hopefully . . . You'll likely get a reboot on the first boot (possible multiple reboots), as SuperSU needs a reboot to install the necessary files. Since your device will also encrypt on that initial boot, I'm not sure whether there will be a conflict or not.
bzowk said:
I really appreciate your help and patience with me!
Click to expand...
Click to collapse
Guess we'll see if it all works out . . .
Thanks!
I proceeded by formatting data, booting directly back intoTWRP, flashing SuperSU, backing up the boot partition, then mounting and copying it over to my PC. The boot.img size was 65,536kb - the same size as the one I unpacked from the RUU. Once unpacked, it was missing the verity_key file and the fstab.qcom file was different + missing the verify flag.
I replaced those two files, then ran repackimg.bat which created image-new.img which I renamed to boot.img. Interesting, though, that this file was only 45,890kb. If it's a repack, shouldn't it be the same or similar? Anyways, the phone was still in TWRP (hadn't booted to system since before the format data) so booted it into bootloader directly and tried flashing boot using my new 45mb boot.img.
If failed - but - my phone was only at 17% power. Don't know if that's why it failed or not so it's charging right now while still in the bootloader. Below is what was echoed when I tried flashing it:
Code:
c:\adb>fastboot flash boot boot.img
target reported max download size of 800000000 bytes
sending 'boot' (45890 KB)...
OKAY [ 3.488s]
writing 'boot'...
(bootloader) HOSD CL#656287
FAILED (remote: 4 RU_BATTERY_LOW please connect charger (17% < 30%))
finished. total time: 4.506s
The reason I didn't boot to system is that I thought that was when the encryption might take place. Going to wait until above 30% power then try flashing again. Powered down to charge, but plan to boot straight back into bootloader to flash. If you see anything that stands out or that I need to do otherwise, please let me know. Otherwise, I'll report back what the result was after getting above 30%.
Thanks again!
bzowk said:
Thanks!
I proceeded by formatting data, booting directly back intoTWRP, flashing SuperSU, backing up the boot partition, then mounting and copying it over to my PC. The boot.img size was 65,536kb - the same size as the one I unpacked from the RUU. Once unpacked, it was missing the verity_key file and the fstab.qcom file was different + missing the verify flag.
I replaced those two files, then ran repackimg.bat which created image-new.img which I renamed to boot.img. Interesting, though, that this file was only 45,890kb. If it's a repack, shouldn't it be the same or similar? Anyways, the phone was still in TWRP (hadn't booted to system since before the format data) so booted it into bootloader directly and tried flashing boot using my new 45mb boot.img.
If failed - but - my phone was only at 17% power. Don't know if that's why it failed or not so it's charging right now while still in the bootloader. Below is what was echoed when I tried flashing it:
Code:
c:\adb>fastboot flash boot boot.img
target reported max download size of 800000000 bytes
sending 'boot' (45890 KB)...
OKAY [ 3.488s]
writing 'boot'...
(bootloader) HOSD CL#656287
FAILED (remote: 4 RU_BATTERY_LOW please connect charger (17% < 30%))
finished. total time: 4.506s
The reason I didn't boot to system is that I thought that was when the encryption might take place. Going to wait until above 30% power then try flashing again. Powered down to charge, but plan to boot straight back into bootloader to flash. If you see anything that stands out or that I need to do otherwise, please let me know. Otherwise, I'll report back what the result was after getting above 30%.
Thanks again!
Click to expand...
Click to collapse
The repack is smaller because the backup uses "dd" to copy the entire block device. Not all that space is actually used after compression. That's nothing to worry about.
And these devices are very picky about flashing only when there's sufficient battery, so I'm sure that's the only reason it failed. TWRP, however, doesn't care how much battery you have, so you could always flash the new boot.img in recovery.
Captain_Throwback said:
The repack is smaller because the backup uses "dd" to copy the entire block device. Not all that space is actually used after compression. That's nothing to worry about.
And these devices are very picky about flashing only when there's sufficient battery, so I'm sure that's the only reason it failed. TWRP, however, doesn't care how much battery you have, so you could always flash the new boot.img in recovery.
Click to expand...
Click to collapse
Hey, hey, hey - think it worked!!
Once I got above 30%, I flashed without issue. I rebooted and was able to format an sd internally successfully, too. Now, I just need to verify it's rooted, but think it is. Thank you so much for your help! I'm going to write a guide for newbs like me to use in the future soon.
Thanks again!
bzowk said:
Hey, hey, hey - think it worked!!
Once I got above 30%, I flashed without issue. I rebooted and was able to format an sd internally successfully, too. Now, I just need to verify it's rooted, but think it is. Thank you so much for your help! I'm going to write a guide for newbs like me to use in the future soon.
Thanks again!
Click to expand...
Click to collapse
If your adopted storage doesn't show as corrupted, and you're able to open the SuperSU app in your app drawer and not get a message that no su binary is installed, you should be good to go .
bad topic
Entire credit goes to @wuxianlin; I've just mirrored and organised stuffs.
Downloads:
Baidu
AFH mirror
Fixed variant by @joemossjr & @charlieb620
Sources:
https://github.com/wuxianlin/android_device_oneplus_enchilada
http://wuxianlin.com/
Screenshots:
https://m.weibo.cn/status/4243215098108813
Instructions:
Download required files from Downloads section.
Unlock the bootloader.
Reboot to bootloader.
Boot into TWRP: fastboot boot recovery-xx.img
Change Partition slot using TWRP: [Reboot => Change_Slot]
(for example, if you're in slot A, change it to slot B and vice versa)
Flash twp-installer zip.
Flash Magisk (use latest) for root access (optional).
Success!
Reserved for future.
Sweet, will give it a shot! Thanks!
Sent from my [device_name] using XDA-Developers Legacy app
Nice
Can't you just do fasboot flash recovery nameofrecovery.img?
JazzieBoi said:
Can't you just do fasboot flash recovery nameofrecovery.img?
Click to expand...
Click to collapse
https://forum.xda-developers.com/showpost.php?p=76626087&postcount=127
Nice
Sent from my ONEPLUS A6000 using Tapatalk
akaHardison said:
Finally,TWRP is ready.
Sent from my ONEPLUS A6000 using Tapatalk
Click to expand...
Click to collapse
Finally? Dude the phone has been out like 3 days in the US and less than 2 weeks I believe anywhere else.
Get some patience maybe.
Is this still a temporary recovery or does this method make TWRP your permanent recovery?
Eric214 said:
Is this still a temporary recovery or does this method make TWRP your permanent recovery?
Click to expand...
Click to collapse
You need to flash TWRP-installer in TWRP, if you want permanent recovery.
Thaaank you very much!
Titokhan said:
Download required files from Downloads section.
Boot into TWRP: fastboot boot recovery-xx.img
Click to expand...
Click to collapse
Which files are required? There are a bunch of different files on that Baidu page.
Which image file should be booted to?
Displax said:
You need to flash TWRP-installer in TWRP, if you want permanent recovery.
Click to expand...
Click to collapse
where can I get twrp-installer from?
Displax said:
You need to flash TWRP-installer in TWRP, if you want permanent recovery.
Click to expand...
Click to collapse
so will making twrp permanent remove the a/b partition? that means i can't flash a/b compatible roms?
@nathanchance... I miss you
Enviado desde mi ONEPLUS A6003 mediante Tapatalk
There is really a lot of files in there. Which img should I boot into for the twrp?
There is a textfile in chinese (i assume) which I let go through google translate:
textfile
Maybe this will give some new information:
Code:
One plus six use ab partition, bring a lot of inconvenience to the brush, temporarily suggest less toss
One, unlock BootLoader (pay attention to backup data)
1. Developer Options Open OEM Unlock
2. Enter the fastboot mode: adb reboot bootloader
3. Unlock: fastboot oem unlock
The mobile phone prompts whether to unlock, the volume key selects Yes, the power button confirms
4 wait to boot
Second, brush into the specific boot
1. The disk boot folder has many types of boot
Introduction:
Official boot: the official original boot, recovery mode for the official recovery
Twrp boot: After brushing into recovery mode becomes twrp
Boot-with-magisk: automatically install migisk after brushing, recovery mode is official recovery, need to install magisk apk
Twrp boot-with-magisk: automatically install migisk after brushing, recovery mode is twrp, need to install magisk apk
name:
For example, boot-180513-h2os.img is based on the hydrogen OS 180513 version, be sure to match the use
Other files are similarly named
2. Brushing method
Enter the fastboot mode: adb reboot bootloader
Brush into the boot partition (boot.img is the path to the file being flushed into)
Fastboot flash boot boot.img
or
Fastboot flash boot_a boot.img
Fastboot flash boot_b boot.img
3. Restart
Fastboot reboot
Third, fastboot brush
Network disk fastboot flashable folder stored fastboot mode can be brushed into the img file
For example, you want to brush the system.img to the system partition (system.img is the path to the file you are working on)
Fastboot flash system system.img
or
Fastboot flash system_a system.img
Fastboot flash system_b system.img
For example, you want to brush the vendor.img to the vendor partition (vendor.img is the path to the file to be scanned)
Fastboot flash vendor vendor.img
or
Fastboot flash vendor_a vendor.img
Fastboot flash vendor_b vendor.img
Fourth, twrp card brush official ROM reserved twrp method
Twrp card brush official ROM brush common patch /twrp folder under the patch package
Note, twrp card brush official ROM, in fact, brush into the current partition does not start, after brushing is complete, activate the partition, restart after running this partition, but at this time twrp run in the current boot partition, need to restart the system into twrp Or restart the recovery mode into twrp, restart the boot partition and the partition started at this time is consistent, brush into the patch for the current boot partition has a role, otherwise the patch package is likely to be brushed into the next boot does not start Partition
Fifth, install magisk
If it is fastboot brush boot, directly brush into the boot with magisk
If it is twrp card brush official ROM, card brush twrp patch, restart twrp or restart boot into twrp, and then brush the patch under the commonly used patch / magisk folder
Six, install the supersu
Twrp card brush official ROM, card brush twrp patch, restart twrp or restart boot into twrp, and then brush the patch / supersu folder patch, even the computer input adb disable-verify, prompt Successfully disabled verity, restart
Seven, install xposed
If you have installed magisk, install xposed directly in magisk
If you have already brushed supersu according to the above method, add the official xposed patch and restart it.
Eight, third-party ROM
Temporarily unknown
Nine, expand the extension
Interested friends are expected to notice that you can choose to brush img into the _a or _b partition in the tutorial of brushing the img into the corresponding partition.
So how do we know if our phone is currently using a partition or b partition?
1.twrp mode, restart, there will be shown below
2. System mode, adb shell getprop ro.boot.slot_suffix
If _a is a partition, _b is partition b
AB Division, except for Google’s mobile phone, it is rare to see other mobile phones use,,,
So there are few methods related to playing online games,,,
Author:
Wuxianlin
Weibo: wuxianlin000000
You can't flash the recovery image... It boots up slowly into the OS, and that's it. Guess we will have to wait a little longer
The TWRP of OP6 looks like Google Pixel this time
Thanks!!!
But which version (file) do I need for Oxygen OS 5.1.5?
In each filename is someting with h2o-rom?
I sucessfully unlocked bootloader, rooted and installed twrp. I was using my phone today and i try to boot to twrp to flash RenovateIce rom and my twrp shows some strange symbols all folders... also on my computer is the same... When i tried to boot to system it just boot up to twrp again.. I cant boot it to my system.. Help please ...
here is screenshot from my pc:
First, you must ask on the Q&A section.
Second your files appears like that because they are crypted ( the password on your phone is used to decrypt it), and as i know (i may be wrong but yes you lost your data) but you need to delete your internal storage now for it to be able to use it like it should, so in twrp delete your internal storage, install your rom via adb sideload, boot and set up your phone and reflash twrp ( via the cmd and then via the zip)
Did you install renovate? You could try to use an otg drive to remove renovate if that is messing your system. They probably have a rescue zip on their forum. You could also try to flash bluspark twrp if that could help you get into your data. Hope you get your data back, otherwise the full format should revive your phone. Read up before (if)you try my suggestions.
hi ,i have fff*cked my op6 many times and i faced this , now go to bootloader and flash twrp from pc cmd or terminal again , boot twrp now u can enter password , good for now u can install sys again or copy your files to another sd card or pc or u can delete data and install system again or just install u can try and learn from your mistake
sorry bad english
vargapirot said:
I sucessfully unlocked bootloader, rooted and installed twrp. I was using my phone today and i try to boot to twrp to flash RenovateIce rom and my twrp shows some strange symbols all folders... also on my computer is the same... When i tried to boot to system it just boot up to twrp again.. I cant boot it to my system.. Help please ...
here is screenshot from my pc:
Click to expand...
Click to collapse
Dude u did loose ur data but lets see if u can get it.
Boot to fastboot
Connect usb
Open powershell in ur adb. Exe/fastboot. Exe windoe,(where u installed adb)
(U can also open powershell & use command cd e:\adb{example} to navigate.
Now u need to download & paste twrp. Img in this forder.
Then, Enter command - fastboot boot twrp.img in powershell.
Ur device will now boot into twrp & u have usb file transfer mode active now .
(Now see if u can extract any data)
If no then
Copy ur os. Zip to phone storage
Now flash os.zip using TWRP.
I sucessfully unbricked without loosing any data...
1. Rebooted to bootloader from twrp
2. Fastboot twrp.img
3. It asked me for password to decrypt
4. Flashed twrp.zip
5. Flashed magisk
6. Reboot to system
Everythings works okay now. I just repeated installing recovery and rooting proccess..
Thank you guys !
I would like to install TWRP and after that Lineage OS on my Samsung S8+ (Exynos). So i tried flashing TWRP with Odin (Dream2lte version 3.3.1.0). But i ran into a FRP lock so i googled and try to solve this, but so far i am unable to.
I have the password to my Google account, so i removed the Google account from the phone and removed the phone from my Google account. After factory reset i am still getting an error FRP lock when flashing.
Shouldn't the FRP lock be gone after removing google account and doing a factory reset? I have tried a couple of YT Howto's but they don't seem to work.
How do i remove the FRP lock so that i am able to install TWRP and Lineage OS?
Like i said i know the password to my Google account and i 100% own the phone
(Bypass probably isn't the correct word, i am simply trying to turn it off )
Got exactly the same problem, hence like you, ended up here for help.
Well i fixed my problem (Disable USB debug and OEM unlock, couple of reboots and enabled them and it worked). But after that i broke my phone
I am stuck at the screen saying: An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software.
I know this is meant to scare me (is kinda working...), but i also know that Odin is still working. So as far as i know i have to flash the original firmware now to fix this. But i keep getting the error: Invalid magic string. When i try to also flash a BL file i get the error: ""Secure CHECK FAIL: (BOOTLOADER)" The option Re-Partition in Odin is switched OFF, as far as i know this is okee... right?
I have tried 3 different versions (Android 9/8/7):
https://www.sammobile.com/samsung/galaxy-s8/firmware/SM-G950F/TNL/download/G950FXXU1AQC9/128974/
https://www.sammobile.com/samsung/galaxy-s8/firmware/SM-G950F/TNL/download/G950FXXU4DSBA/259612/
https://www.sammobile.com/samsung/galaxy-s8/firmware/SM-G950F/TNL/download/G950FXXS4CSA4/256485/
This zip files contain a BL/AP/CP/CSC file, i have tried them all at the same time in Odin as well as the AP and BL files seperate. (from one zip file, NOT different version files together of course)
I tried using Smart Switch 4.1 to do the emergency procedure using model nummer SM-G955F with my serial number but before it does anything it tells me this is not possible with an SM-G955F.
They all give me the same result.
Does anybody know how to fix this?
TheGeneral said:
Well i fixed my problem (Disable USB debug and OEM unlock, couple of reboots and enabled them and it worked). But after that i broke my phone
I am stuck at the screen saying: An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software.
I know this is meant to scare me (is kinda working...), but i also know that Odin is still working. So as far as i know i have to flash the original firmware now to fix this. But i keep getting the error: Invalid magic string. When i try to also flash a BL file i get the error: ""Secure CHECK FAIL: (BOOTLOADER)" The option Re-Partition in Odin is switched OFF, as far as i know this is okee... right?
I have tried 3 different versions (Android 9/8/7):
https://www.sammobile.com/samsung/galaxy-s8/firmware/SM-G950F/TNL/download/G950FXXU1AQC9/128974/
https://www.sammobile.com/samsung/galaxy-s8/firmware/SM-G950F/TNL/download/G950FXXU4DSBA/259612/
https://www.sammobile.com/samsung/galaxy-s8/firmware/SM-G950F/TNL/download/G950FXXS4CSA4/256485/
This zip files contain a BL/AP/CP/CSC file, i have tried them all at the same time in Odin as well as the AP and BL files seperate. (from one zip file, NOT different version files together of course)
I tried using Smart Switch 4.1 to do the emergency procedure using model nummer SM-G955F with my serial number but before it does anything it tells me this is not possible with an SM-G955F.
They all give me the same result.
Does anybody know how to fix this?
Click to expand...
Click to collapse
Secure check fail on bootloader is your flashing a older firmware than on the device. Look at the builds 5th from last digit. You need to flash that equal or greater than.
The error screen you see for emergency recovery is ok. It's like a modified version of download mode. Kind of. You can still flash Odin files from said screen. Ii see you've flashed a bit 1. And two bit 4 firmwares. So you must be on a 5 or greater. I don't know the exy bit number but like snapdragon is at or near 7 or 8. I can explain better if you need. But not an exynos expert
TheMadScientist said:
Secure check fail on bootloader is your flashing a older firmware than on the device. Look at the builds 5th from last digit. You need to flash that equal or greater than.
The error screen you see for emergency recovery is ok. It's like a modified version of download mode. Kind of. You can still flash Odin files from said screen. Ii see you've flashed a bit 1. And two bit 4 firmwares. So you must be on a 5 or greater. I don't know the exy bit number but like snapdragon is at or near 7 or 8. I can explain better if you need. But not an exynos expert
Click to expand...
Click to collapse
Thanks for your reply! I am in the normal "Downloading...." screen is there anywhere i can check which number i am at?
But i have just tried this one: G950FXXS7DTA6_G950FOXM7DTA6_PHN and it is not working. But this is the newest one available on sammobile. Still the same bootloader error.
I have tried TWRP 3.3.1.0 and that worked, now i am in the TWRP menu but i don't have the LineageOS 17 + GoApps copied to the root. So i cannot install LineageOS now. What do i do now? My computer sees a SM-G955F but it is not showing any storage, if i can fix this i could copy the LineageOS files to the root...right?
TheGeneral said:
Thanks for your reply! I am in the normal "Downloading...." screen is there anywhere i can check which number i am at?
But i have just tried this one: G950FXXS7DTA6_G950FOXM7DTA6_PHN and it is not working. But this is the newest one available on sammobile. Still the same bootloader error.
I have tried TWRP 3.3.1.0 and that worked, now i am in the TWRP menu but i don't have the LineageOS 17 + GoApps copied to the root. So i cannot install LineageOS now. What do i do now? My computer sees a SM-G955F but it is not showing any storage, if i can fix this i could copy the LineageOS files to the root...right?
Click to expand...
Click to collapse
1. If you are on an S8+ flashing firmware for the S8 will cause you issues. Download firmware for the S8+ only. ie: 955f not 950f.
2. If you can't get into the system but can get into download mode there should be a line saying
AP SWREV: B:? K:? S:?
The B:? Is your bootloader version number. You will need to flash the same or higher.
3. How did you install TWRP?
If you don't have an SD card to store files on then after the Format Data stage you can then copy files from pc to phones internal storage.
spawnlives said:
1. If you are on an S8+ flashing firmware for the S8 will cause you issues. Download firmware for the S8+ only. ie: 955f not 950f.
2. If you can't get into the system but can get into download mode there should be a line saying
AP SWREV: B:? K:? S:?
The B:? Is your bootloader version number. You will need to flash the same or higher.
3. How did you install TWTP?
If you don't have an SD card to store files on then after the Format Data stage you can then copy files from pc to phones internal storage.
Click to expand...
Click to collapse
I am a bit embarrassed, it looks like i have been trying to flash the wrong ROMs last night 950 instead of 955, i am downloading the correct files now and wil try again. Sorry for this dumb mistake!
Just to be sure, i am trying to do this:
https://www.getdroidtips.com/lineage-os-17-samsung-galaxy-s8/
(I do know that this site says S8, but i picked the right files this time and thought the process would be the same)
But i first Flash TWRP with Odin, otherwise i cannot reach the TWRP recovery menu right?
But when i look bullet 5 (not number 5) it looks like i need to flash TWRP from within the TWRP menu. But that is not correct right?
I have placed these zip files on the phone:
lineage-17.1-20200211-UNOFFICIAL-dreamlte.zip
open_gapps-arm64-10.0-pico-20200303.zip
As a zip and unpacked, but when i am in the TWRP menu and i go to install, i cannot find the zip files. I placed them in the highest folder level possible. Why can't i find them now?
TheGeneral said:
I am a bit embarrassed, it looks like i have been trying to flash the wrong ROMs last night 950 instead of 955, i am downloading the correct files now and wil try again. Sorry for this dumb mistake!
Just to be sure, i am trying to do this:
https://www.getdroidtips.com/lineage-os-17-samsung-galaxy-s8/
(I do know that this site says S8, but i picked the right files this time and thought the process would be the same)
But i first Flash TWRP with Odin, otherwise i cannot reach the TWRP recovery menu right?
But when i look bullet 5 (not number 5) it looks like i need to flash TWRP from within the TWRP menu. But that is not correct right?
I have placed these zip files on the phone:
lineage-17.1-20200211-UNOFFICIAL-dreamlte.zip
open_gapps-arm64-10.0-pico-20200303.zip
As a zip and unpacked, but when i am in the TWRP menu and i go to install, i cannot find the zip files. I placed them in the highest folder level possible. Why can't i find them now?
Click to expand...
Click to collapse
I don't use custom roms yet.
Try searching for you device S8+ for installation instructions. Had a quick look the firmware is for S8 only not S8+. Need dream2lit for S8+
Try in separate stages instead of all at once.
I would sort out your stock firmware first get it up and running.
Then install TWRP. Install for S8+ from
http://twrp.me/Devices/Samsung/
They are many guides for this
https://forum.xda-developers.com/ga...pment/recovery-twrp-galaxy-s8-exynos-t3595102
If you need rmm bypass zip
https://forum.xda-developers.com/sa...w-to/guide-root-install-twrp-samsung-t3747535
Get that up and running properly.
Then you can install custom roms,root etc.
In regards to transferring files to phone they need to be a zip file ( .zip ) or an image ( .img ) files to flash in TWRP.
Maybe select internal storage then from menu select sdcard folder check if file is there.
spawnlives said:
I don't use custom roms yet.
Try searching for you device S8+ for installation instructions. Had a quick look the firmware is for S8 only not S8+. Need dream2lit for S8+
Try in separate stages instead of all at once.
I would sort out your stock firmware first get it up and running.
Then install TWRP. Install for S8+ from
http://twrp.me/Devices/Samsung/
They are many guides for this
https://forum.xda-developers.com/ga...pment/recovery-twrp-galaxy-s8-exynos-t3595102
If you need rmm bypass zip
https://forum.xda-developers.com/sa...w-to/guide-root-install-twrp-samsung-t3747535
Get that up and running properly.
Then you can install custom roms,root etc.
In regards to transferring files to phone they need to be a zip file ( .zip ) or an image ( .img ) files to flash in TWRP.
Maybe select internal storage then from menu select sdcard folder check if file is there.
Click to expand...
Click to collapse
I am using dream2lit.
I have the correct factory stock ROM (now), so i can always go back now. But i agree, my preparation wasn't good enough.
I will look at the links, but for now like i said my problem is that i cannot see my files in TWRP. But maybe that will be addressed in one of your links
With regards to your first link, i used the "Odin Method" so as far as i can tell i did this the right way(https://twrp.me/samsung/samsunggalaxys8plus.html):
Odin Install Method (No Root Required):
You will need to download and install Odin on your PC. Once you have Odin installed, download the proper .tar file for your device from the download link above. Power off your device. Turn on your device using the proper key combo to get into download mode and attach the device to your computer via a USB cable. Use the PDA tab or button to browse to and select the tar file that you downloaded and flash the device.
Note many devices will replace your custom recovery automatically during first boot. To prevent this, use Google to find the proper key combo to enter recovery. After typing fastboot reboot, hold the key combo and boot to TWRP. Once TWRP is booted, TWRP will patch the stock ROM to prevent the stock ROM from replacing TWRP. If you don't follow this step, you will have to repeat the install.
TheGeneral said:
I am using dream2lit.
I have the correct factory stock ROM (now), so i can always go back now. But i agree, my preparation wasn't good enough.
I will look at the links, but for now like i said my problem is that i cannot see my files in TWRP. But maybe that will be addressed in one of your links
With regards to your first link, i used the "Odin Method" so as far as i can tell i did this the right way(https://twrp.me/samsung/samsunggalaxys8plus.html):
Odin Install Method (No Root Required):
You will need to download and install Odin on your PC. Once you have Odin installed, download the proper .tar file for your device from the download link above. Power off your device. Turn on your device using the proper key combo to get into download mode and attach the device to your computer via a USB cable. Use the PDA tab or button to browse to and select the tar file that you downloaded and flash the device.
Note many devices will replace your custom recovery automatically during first boot. To prevent this, use Google to find the proper key combo to enter recovery. After typing fastboot reboot, hold the key combo and boot to TWRP. Once TWRP is booted, TWRP will patch the stock ROM to prevent the stock ROM from replacing TWRP. If you don't follow this step, you will have to repeat the install.
Click to expand...
Click to collapse
Note: Samsung don't have fastboot commands. Have to use button configurations to enter recovery or download modes.
What stage are you at?
It will give me a better idea to be able to help more.
spawnlives said:
Note: Samsung don't have fastboot commands. Have to use button configurations to enter recovery or download modes.
What stage are you at?
It will give me a better idea to be able to help more.
Click to expand...
Click to collapse
Well i installed Lineage OS 17.1 and Open Apps (lineage-17.1-20200211-UNOFFICIAL-dream2lte and open_gapps-arm64-10.0-pico-20200303) with an OTG plug and an USB stick. After installing i removed the USB Stick. But now i am having a new problem...
When the phone boots it asks: "To start Android, enter your password"
Which password is this? When i enter a password i often use it works but then:
"Decryption unsuccessful
The password you entered is correct, but unfortunately your data is corrupt. (Which is no problem)
To resume using your phone, you need to perform a factory reset. When you set up your phone after the reset, you'll have an opportunity to restore any data that was backed up to your Google account.
(Button) Erase ALL DATA"
Of course i erase the data. Look at the attachment to see what happens then.
I will not give up, will get Lineage OS on this phone, and after that on my Tablet S2 and maybe even on my primairy phone (S10+)
What should i do now? Many thanks for all the help so far, and for help finishing this proces
TheGeneral said:
Well i installed Lineage OS 17.1 and Open Apps (lineage-17.1-20200211-UNOFFICIAL-dream2lte and open_gapps-arm64-10.0-pico-20200303) with an OTG plug and an USB stick. After installing i removed the USB Stick. But now i am having a new problem...
When the phone boots it asks: "To start Android, enter your password"
Which password is this? When i enter a password i often use it works but then:
"Decryption unsuccessful
The password you entered is correct, but unfortunately your data is corrupt. (Which is no problem)
To resume using your phone, you need to perform a factory reset. When you set up your phone after the reset, you'll have an opportunity to restore any data that was backed up to your Google account.
(Button) Erase ALL DATA"
Of course i erase the data. Look at the attachment to see what happens then.
I will not give up, will get Lineage OS on this phone, and after that on my Tablet S2 and maybe even on my primairy phone (S10+)
What should i do now? Many thanks for all the help so far, and for help finishing this proces
Click to expand...
Click to collapse
Mounting data errors in twrp generally ( but not always ) means your device is encrypted/re-encrypted when booting into system. Twrp has issues with encrypted devices.
What version twrp are you using?
Have you flashed the no-verity-opt-encypt zip in twrp. This zip file will prevent device from re-encrypting when booting phone back into the system ( after the Format Data stage / reboot back into twrp)
https://build.nethunter.com/android-tools/no-verity-opt-encrypt/
What is your process of installing twrp?
If you have any passwords etc. installed delete them until after setting up you phone.
spawnlives said:
Mounting data errors in twrp generally ( but not always ) means your device is encrypted/re-encrypted when booting into system. Twrp has issues with encrypted devices.
What version twrp are you using?
Have you flashed the no-verity-opt-encypt zip in twrp. This zip file will prevent device from re-encrypting when booting phone back into the system ( after the Format Data stage / reboot back into twrp)
https://build.nethunter.com/android-tools/no-verity-opt-encrypt/
What is your process of installing twrp?
If you have any passwords etc. installed delete them until after setting up you phone.
Click to expand...
Click to collapse
I am using version twrp-3.3.1-1-dream2lte and no i have not flashed that no-verity-opt-encypt zip. I assume i should flash this one the same way flash the Lineage ROM right?
No passwords used on the phone.
My process:
i put the phone in download mode (POWER+BIXBY+VOL DOWN)
I use ODIN to flash twrp-3.3.1-1-dream2lte, and when the phone reboot i press POWER+BIXBY+VOL UP to enter TWRP menu,
Then i go to WIPE and Advanced Wipe and i select the data, system and davlik cache. Then swipe to wipe it.
Then i go to INSTALL and flash lineage-17.1-20200211-UNOFFICIAL-dream2lte and open_gapps-arm64-10.0-pico-20200303
TheGeneral said:
I am using version twrp-3.3.1-1-dream2lte and no i have not flashed that no-verity-opt-encypt zip. I assume i should flash this one the same way flash the Lineage ROM right?
No passwords used on the phone.
My process:
i put the phone in download mode (POWER+BIXBY+VOL DOWN)
I use ODIN to flash twrp-3.3.1-1-dream2lte, and when the phone reboot i press POWER+BIXBY+VOL UP to enter TWRP menu,
Then i go to WIPE and Advanced Wipe and i select the data, system and davlik cache. Then swipe to wipe it.
Then i go to INSTALL and flash lineage-17.1-20200211-UNOFFICIAL-dream2lte and open_gapps-arm64-10.0-pico-20200303
Click to expand...
Click to collapse
To install TWRP
1. Flash twrp with odin - reboot straight into twrp
2. In wipe menu select Format Data ( bottom right )
Type yes to format
3. Reboot back into twrp ( use twrp menu )
4. Flash no-verity-opt zip and if needed rmm bypass zip ( using install button in twrp ).
5. Reboot back into twrp then reboot to system using twrp menu.
6. From system reboot back into twrp.
To check if device is un-encrypted use backup menu - check data storage size ( If reading 0mb then device is still encrypted ).
Note: If all ok I would do a complete twrp backup at this stage ( keep backup on a separate storage device ).
Then you can install custom Rom's as per the installation guide of that Rom.
spawnlives said:
To install TWRP
1. Flash twrp with odin - reboot straight into twrp
2. In wipe menu select Format Data ( bottom right )
Type yes to format
3. Reboot back into twrp ( use twrp menu )
4. Flash no-verity-opt zip and if needed rmm bypass zip ( using install button in twrp ).
5. Reboot back into twrp then reboot to system using twrp menu.
6. From system reboot back into twrp.
To check if device is un-encrypted use backup menu - check data storage size ( If reading 0mb then device is still encrypted ).
Note: If all ok I would do a complete twrp backup at this stage ( keep backup on a separate storage device ).
Then you can install custom Rom's as per the installation guide of that Rom.
Click to expand...
Click to collapse
how do i make a complete TWRP backup? and what is rmm bypass and how do i know if it is neccessary to install this zip file?
TheGeneral said:
how do i make a complete TWRP backup? and what is rmm bypass and how do i know if it is neccessary to install this zip file?
Click to expand...
Click to collapse
In twrp main menu
Select backup menu - select ( all ) partitions - select storage location ( bottom left of screen ) - then swipe to backup.
Note:
1. If backing up to internal storage copy/move backup to an external storage ie: PC, sd card.etc.
2. Since you want a custom rom backup of the EFS partition is important.
Rmm state can be found in download mode. It will have a line ( near the top ) saying RMM state. It will either say prenormal or normal /disappeared.
It won't hurt to flash it just in case.
See OP in the thread I sent before:
https://forum.xda-developers.com/sa...w-to/guide-root-install-twrp-samsung-t3747535
spawnlives said:
To install TWRP
1. Flash twrp with odin - reboot straight into twrp
2. In wipe menu select Format Data ( bottom right )
Type yes to format
3. Reboot back into twrp ( use twrp menu )
4. Flash no-verity-opt zip and if needed rmm bypass zip ( using install button in twrp ).
5. Reboot back into twrp then reboot to system using twrp menu.
6. From system reboot back into twrp.
To check if device is un-encrypted use backup menu - check data storage size ( If reading 0mb then device is still encrypted ).
Note: If all ok I would do a complete twrp backup at this stage ( keep backup on a separate storage device ).
Then you can install custom Rom's as per the installation guide of that Rom.
Click to expand...
Click to collapse
I am really trying to do what you are saying...but when i try to "Format Data" (Step 2) it shows an error "Failed to mount '/preload' (Invalid argument). When i try to install no-verity-opt zip (step 4) at the end it shows the same error "Failed to mount '/preload' (Invalid argument). Which is probably because format data failed?
I am installing the zip from an USB stick with an USB-C to USB-A Converter. I don't think that could be the problem?
As Expected the "Data (excl. storage) is still showing 0MB.
TheGeneral said:
I am really trying to do what you are saying...but when i try to "Format Data" (Step 2) it shows an error "Failed to mount '/preload' (Invalid argument). When i try to install no-verity-opt zip (step 4) at the end it shows the same error "Failed to mount '/preload' (Invalid argument). Which is probably because format data failed?
I am installing the zip from an USB stick with an USB-C to USB-A Converter. I don't think that could be the problem?
As Expected the "Data (excl. storage) is still showing 0MB.
Click to expand...
Click to collapse
Failed to mount preload seems to affect some users.
You could try after the format data and reboot back into twrp ( using twrp 3.3.1.1 ):
Select wipe menu
Select advanced wipe
Select Preload
Swipe to wipe
Reboot back into twrp
Then try flashing no-verity/rmm zips files - reboot back into twrp.
Normally, for me , after this stage If i still get 0mb I will reboot into the Android system and then back into twrp. Then check in backup menu storage. If ok then try to flash custom rom.
spawnlives said:
Failed to mount preload seems to affect some users.
You could try after the format data and reboot back into twrp ( using twrp 3.3.1.1 ):
Select wipe menu
Select advanced wipe
Select Preload
Swipe to wipe
Reboot back into twrp
Then try flashing no-verity/rmm zips files - reboot back into twrp.
Normally, for me , after this stage If i still get 0mb I will reboot into the Android system and then back into twrp. Then check in backup menu storage. If ok then try to flash custom rom.
Click to expand...
Click to collapse
Yes Yes!! After doing the Preload i am able to flash no-verity/rmm zips file.
But Data is still showing 0MB.....
I thought why not give the lineage OS rom flashing another try. That worked, but now the phone seems to hang on a Lineage OS logo with a small circle moving around not straight line.
So i wiped everything again and flashed no-verity/rmm zip file, and will wait what for some advice and what do to next.
TheGeneral said:
Yes Yes!! After doing the Preload i am able to flash no-verity/rmm zips file.
But Data is still showing 0MB.....
I thought why not give the lineage OS rom flashing another try. That worked, but now the phone seems to hang on a Lineage OS logo with a small circle moving around not straight line.
So i wiped everything again and flashed no-verity/rmm zip file, and will wait what for some advice and what do to next.
Click to expand...
Click to collapse
Have you tried to reboot into system through twrp ie: reboot menu - system. Let it start normally, reboot into twrp, then check storage size. ( This is after the flashing of the no-verity/rmm zip and rebooting back into twrp ).
As I said I' m not familiar with custom ROMs. I do know that some custom ROMs do take some time to boot up on installation.
But out of curiosity I have a spare S8 and will give it a go.
This guide is general guide for the installation of custom ROMs. I will also include guide to install stock ROM on devices which have been bricked or for solving various problem which you may encounter in custom ROMs. There are other guides for the same purpose but most of them are outdated and many of you seem to ignore old guide despite the fact that those guides can be helpful.
This is guide is only relevant for installation of custom ROMs which were released up to the date of posting this guide or up to android version 11. Recovering a bricked device can be done in the same way as to this one but installation instruction for devices with android version greater than 11 may differ.
DISCLAMER
Code:
I am NOT responsible for bricked devices,
thermonuclear war or for you getting fired because your alarm app failed.
Make sure the bootloader is unlocked and never lock the bootloader
How to unlock bootloader ?
>See in this thread.
Hard Brick, Soft brick, Problems in custom rom due to bad base, installation of base for switching to custom roms: windows linux
Installation of stock ROM through fastboot : The reply below
Migration from stock base to custom ROM : CLEAN FLASH
Migration between different version of same custom ROM : DIRTY FLASH
FOR SPECIFIC THREADS
Oragne Fox For Daisy
TWRP For Daisy
Magisk
CREDITS:
LInkBoi for his previous guide and TWRP
DarthJabba9 for Orange Fox Recovery
Every pros in daisy telegram groups.
EDL FLASHING (For windows only)
EDL flashing can be helpful when flashing every partition of device is needed either for clean stock base or after brick or after some failure.
EDL flashing can be the final resort when everything else fails.
PREREQUISITES
1) A good USB cable, your phone
2) A PC with either windows or linux
3) Fastboot drivers from google and edl drivers from qualcomm
4) Platform tools from google
5)Fastboot rom. This should be full rom in .tgz format.
6)Xiaomi flash tool (LATEST VERSION AVAILABLE)
Install the adb and fastboot drivers from google. If you are on windows 10 or greater then you can also use "windows update > optional updates" to update adb and fastboot drivers + edl drivers. For the installation of drivers always use trusted sources and don't turn of driver signature enforcement if you can.
Extract the platform tools in a convenient folder, we will be doing our operations from this folder for fastboot and adb opeartions. Extract the fastboot ROM and place that in convenient folder as well. And for xiaomi flash tool extract the zip and launch XiaoMiFlash.exe .
If you can access fastboot in you phone then the phone can be booted into edl mode through fastboot else you have to take out back cover and short the testpoint pins to make the device boot into edl mode (see the attached image ).
If you can access fastboot. Boot into fastboot and type the following command in terminal.
To check if device is connected properly and drivers are properly installed
If no devices is shown then connect device properly with good usb cable and check the drivers.
Code:
fastboot devices
To boot phone into edl mode. This is only possible if the bootloader is unlocked else testpoint-edl is the only option
Code:
fastboot oem edl
The device should be shown as COM device in device manager ( Windows ). If not then either drivers aren't installed properly or your phone isn't in edl mode.
Now click on refresh button in xiaomi flash tool. Your device should be recognized as com device. Set the path to the images folder ( extracted fastboot rom ). Select CLEAN ALL option . If everything is good then click
on FLASH. The flashing process should start now. After the process completes keep pressing power button to boot device into the currently installed ROM.
Just install the rom and setup once even if you're going to flash custom rom next. This reduces various problems which may come in custom ROMs.
If any error occurs then try the following:
Make sure you are using latest flash tool.
Good fastboot rom (shouldn't be corrupted )
Good USB cable and try different ports of the PC.
The flashing should be done immediately after booting to edl. If not then take out battery and reconnect it if you have back cover open(In case of hard brick). Or keep pressing power button and volume down to boot into fastboot and boot to edl mode again from the above instructions(If fastboot is accessible)
For booting to edl using testpoint:
> Take out backcover
> Disconnect battery
> Short the pins
> Flash
> Connect battery after flashing is complete
> Keep pressing power button to boot into system.
qdl flashing ( linux only )
For very detailed guide github -> bkerler edl
Thanks to DEFXZ and LinkBoi for suggesting this alternative.
Make sure you have platform tools, fastboot rom and other prerequisites to detect device properly.
clone the repository in convenient place
Code:
git clone https://git.linaro.org/landing-teams/working/qualcomm/qdl.git --depth=1
change to qdl directory
Code:
cd qdl
Build qdl tool
Code:
make
Finally flash the rom
Code:
./qdl --storage emmc --include /path/to/stock/images /path/to/stock/images/prog_emmc_firehose_8953_ddr.mbn /path/to/stock/images/rawprogram0.xml /path/to/stock/images/patch0.xml
The paths are the paths to various files inside the images folder which will be obtained after fastboot rom is extracted.
For further informations:
Original github link
qdl discussion in XDA
FASTBOOT FLASHING
PREREQUISITES
FASTBOOT DRIVERS
PLATFORM TOOLS
FASTBOOT ROM
GOOD USB CABLE
PC WITH WORKING USB PORT
See this for meeting prerequisites.
Install fastboot drivers, connect device to PC via USB.
Extract platform tools into a convenient folder.
Extract fastboot ROM into a convenient folder.
Go to platform tools folder ( this will contain files and executable like fastboot.exe) and open powershell or any terminal window there
[ shift + right click and select open (powershell) window here ]
Type this command to see everything worked correctly.
Code:
fastboot devices
If not then check every step properly.
Now execute the script to flash the ROM.
Execute flash_all.bat script for windows PC.
Execute flash_all.sh script for linux PC.
If platform tools cannot be accessed system wide then.
Code:
./fastboot devices
will provide fastboot devices information.
For flashing drag and drop flash_all.bat or flash_all.sh file into the terminal.
Code:
'/media/user001/user/daisy/stock_roms/daisy_global_images_V10.0.18.0.PDLMIXM_9.0/flash_all.sh'
It will look something like this in linux and similar in windows.
If any error occurs the search for particular error. Most of the times the error is due to corrupted fastboot ROM or bad connection between phone and PC.
FINALLY! FLASHING CUSTOM ROM
STEP 0
Flash(if not flashed already) the stock base recommended by particular ROM, if the ROM doesn't recommend a specific stock base flash 10.0.18.0 from the above instructions.
PREREQUISITES
TWRP or ORANGE FOX RECOVERY
Fastboot drivers and platform tools (details above )
The ROM which you want to flash, choose from here
GAPPS package if rom is vanilla and you want to install it.
Magisk if you want to root.
As you may have known by experience, our device doesn't have recovery partition so, flashing recovery through fastboot isn't possible. For flashing recovery first we need to boot recovery image and then only we can flash it.
If you want to use twrp:
Download both twrp*.zip and twrp*.img and place it in a convenient place.
If you want to use orange fox recovery:
Download orangeFox*.zip and extract it.
Keep both the .zip and .img file in convenient place.
If you have sdcard then copy ROM file, gapps, magisk, twrp or orange fox files into sdcard.
If not then there will be further instructions.
Now, connect the phone to the PC via USB and enable usb debugging. And open terminal in the platform tools folder as in above instructions.
Check device connectivity:
Code:
adb devices
Reboot into fastboot:
Code:
adb reboot bootloader
Check device connectivity:
Code:
fastboot devices
Lets check if the bootloader is unlocked:
Code:
fastboot oem device-info
If bootloader isn't unlocked you won't be able to flash custom recovery into the device. So, first unlock the bootloader. This should be allowed in the developers option of your phone first. This will factory reset the device.
Code:
fastboot oem unlock
Now if everything is good then it's time to boot into custom recovery:
Code:
fastboot boot recovery.img
recover.img is name of image of whichever custom recovery you want to use.
Code:
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
It's like this in my case. You can drag and drop after typing fastboot boot
The phone should now boot into custom recovery. If it ask for decryption then your lockscreen password should work there.
if you want to flash recovery only then find the recovery.zip you want and flash it.
The steps further is also valid for moving between different custom roms. The term used for such process is CLEAN FLASH.
For Flashing custom ROMS :
SOMETIMES FLASHING INSTRUCTIONS MAY DIFFER SO, BE SURE TO CROSS CHECK FOR INSTRUCTION IN ROM SPECIFIC XDA THREAD OR TELEGRAM GROUP
The following action will wipe userdata if not wiped already. Be sure to backup data before these steps. Also if you encounter any future problems full backup from custom recovery may be able to solve most of the problems. So, be sure to keep full backup(including every partition) of your device.
Go to main menu > wipe > select all except internal storage and microSD.
Swipe right to perform wipe.
Install custom recovery by flashing recovery.zip
(This is done in case adb push doesn't work below and sdcard isn't available for flashing)
Again go to main menu > wipe > format data
Type yes and press enter.
If you don't have files in your sdcard then:
push rom file + gapps + other files into your device through adb push.
The command will be something like this:
Code:
adb push '/media/user001/storage (1)/daisy/posp/potato_daisy-11-20210919-dumaloo.v4.2.3+20.Community.zip' /sdcard
If adb push fails to work then you can reboot recovery and simply copy the files through file explorer.
Reboot to recovery only if you had installed recovery after wiping system else the device will soft brick
Now flash the rom.zip by selecting the file and swiping right.
Flash custom recovery if the ROM doesn't contain recovery
We have to change current slot even if we don't want to flash anymore things.
Latest recoveries changes slot automatically So, go to main menu > reboot > recovery
Now flash files which you want to flash i.e. gapps and magisk.
Again, Don't flash gapps if the ROM is of Gapps variant
Most of the roms now have implemented FBE (File Based Encryption ). So, you need to format data before rebooting to system. Again, check for specific ROM installation instruction if that is required or not. If you keep data from previous ROM that won't be considered a clean flash so, for proper clean flash format data before rebooting to system.
reboot system
MOVING BETWEEN DIFFERENT VERSION OF SAME CUSTOM ROM
Dirty flash or OTA
Most of the newer ROMs have seamless update ( even the unofficial ones ). The OTA update is simple. Just go to updater ( in settings > system or native app, depends upon the rom). If your ROM is of vanilla version then make sure gapps and/or magisk which you have installed, your ROM and custom recovery all support addon.d survival script. If they don't then you may have to flash everything again after update process is complete.
If custom recovery itself doesn't support update then you may need to choose different recovery or dirty flash ROM from the recovery. Don't worry most of the roms and both the recoveries for daisy support OTA and addon.d survival.
DIRTY FLASHThe process of flashing a ROM on top of existing one keeping the /data partition intact is known as dirty flashing. Such flashing must be done only on different builds of same ROM and it isn't recommended to flash build of lower version on top of higher version.
The steps for dirty flashing:
Download the update package.
Reboot to recovery
Enter password for decryption if encrypted.
Flash the update.zip package.
Reboot recovery, if recovery/rom doesn't support survival of recovery then flash recovery before rebooting to recovery.
If gapps and/or magisk survival isn't supported then flash gapps and magisk, make sure gapps is of the same type which was flashed before.
reboot system
Hi @user-001 thanks for this.
I'm on a stock A2 lite thats never had anything done to it , am i right in thinking i follow the clean flash section ?
You mention in there
We have to change current slot even if we don't want to flash anymore things.
Click to expand...
Click to collapse
I'm not fully sure what that involves could you break it down the steps a little for me.
I've downloaded all the files and am set up but i'm unsure on the Flashing fastbbot section where you say to use these files..
Execute flash_all.bat script for windows PC.
Click to expand...
Click to collapse
Is this a section i can bypass ? if not where can i get them from ?
Cheers
steve.loveday said:
Hi @user-001 thanks for this.
I'm on a stock A2 lite thats never had anything done to it , am i right in thinking i follow the clean flash section ?
You mention in there
I'm not fully sure what that involves could you break it down the steps a little for me.
I've downloaded all the files and am set up but i'm unsure on the Flashing fastbbot section where you say to use these files..
Is this a section i can bypass ? if not where can i get them from ?
Cheers
Click to expand...
Click to collapse
1) Yes you should follow clean flash instructions.
2)Changing of slot is done in custom recovery. Precisely in the reboot menu. But newer recoveries automatically switch the slot after flashing the rom , just be sure to reboot to recovery after flashing the recovery zip file.
3) the flash_all.bat script will be inside the extracted rom(fastboot rom) folder. You can use xiaomiflash too for flashing through fastboot.
user-001 said:
1) Yes you should follow clean flash instructions.
2)Changing of slot is done in custom recovery. Precisely in the reboot menu. But newer recoveries automatically switch the slot after flashing the rom , just be sure to reboot to recovery after flashing the recovery zip file.
3) the flash_all.bat script will be inside the extracted rom(fastboot rom) folder. You can use xiaomiflash too for flashing through fastboot.
Click to expand...
Click to collapse
Hi thanks for the reply,
I'm getting confused with all the various guides all seem to want you to do it a different way.
As i'm wanting Lineage thier instructions are...
Installation:
Download the latest build from here
Download LinkBoi00's version of TWRP here
Reboot to bootloader (adb reboot bootloader)
Fastboot into TWRP recovery (fastboot boot twrp*.img)
Do a factory reset in TWRP
Flash the latest build of Lineage OS
Boot into your new phone
Click to expand...
Click to collapse
Theres no mention of the edl or fastboot flashing and also the fastbot rom i downloaded doesnt have the flash_all.bat script in the zip file.
So do i follow thier instructions or these ones ?
Cheers
steve.loveday said:
Theres no mention of the edl or fastboot flashing and also the fastbot rom i downloaded doesnt have the flash_all.bat script in the zip file.
So do i follow thier instructions or these ones ?
Cheers
Click to expand...
Click to collapse
This guide deals with how to do something rather than what to do, meaning you should always do what particular rom suggests but the way to do this is mentioned here.
edl or fastboot flashing comes under clean flashing with new base, most of the time you aren't required to do this.
The script should be clean_all.bat or something similar just don't execute script with lock in the name(it will lock the bootloader)
And if you're already on the recommended base you don't have to flash the fastboot rom.
First of all, thank you very much for the detailed guide. What you have done here took a lot of work to do but it will help a lot of people (including me) to understand, albeit rudimentarily, the structures and functions of the devices etc.
For all that, thanks again.
When I start using the guide, I will update this post with any questions, such as :
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
why not doing below? (For those who, like me, are not very familiar with linux.)
1. > adb push <twrp.img> /sdcard or same adb push "C:\platform-tools\twrp-3.5.2_9-2-daisy-unofficial.img" /sdcard
( which means push <file> from "adb|platform-tools\ folder" (eg. C:\platform-tools\)
into the root of <internal storage> | /storage/emulated/0 )
2. Reboot from adb to fastboot:
> adb reboot bootloader
3. Boot the image from <internal storage>:
> fastboot boot /sdcard/twrp-3.5.2_9-2-daisy-unofficial.img
What is the "Red" pointed and "Yellow" addresses"?
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
I followed your "EDL FLASHING" post (#2) and it worked exactly as you mention!
In short, I was comming from unsuccessful flashing... but this is out of topic.
For me, did not worked the first time (after restarts) but the other day worked perfect.
The point is, most of times, it's becase windowz drivers.
We have to point that windowz needs their time to take the drivers in place. So, be patient and leave windowz to (not forced) restart(s).
AntonyMan said:
What is the "Red" pointed and "Yellow" addresses"?
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
Click to expand...
Click to collapse
That must be your terminal representing different type of character in different colors.
Or, Are you talking about something else ?
steve.loveday said:
Theres no mention of the edl or fastboot flashing and also the fastbot rom i downloaded doesnt have the flash_all.bat script in the zip file.
So do i follow thier instructions or these ones ?
Cheers
Click to expand...
Click to collapse
For future references, the extracted fastboot ROM should be like this and you need to execute flash_all.bat or flash_all.sh script depending upon your OS or terminal.
user-001 said:
That must be your terminal representing different type of character in different colors.
Or, Are you talking about something else ?
Click to expand...
Click to collapse
Of course I'm talking about something else. lol
I was talking about that 'strange' address. fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img' (explained in post #11)
There is not such a directories in my miA2Lite phone. Obviously, it's because you are on Linux or Mac (UNIX). On Windowz 'command prompt' syntax it's slightly different.
Thus, I typed fastboot boot "/sdcard/twrp-3.5.2_9-2-daisy-unofficial.img"
* /sdcard is the root of <internal storage> directory.
** On Windows, double quote the address, if it's include spaces.
AntonyMan said:
Of course I'm talking about something else. lol
I was talking about that 'strange' address. There is not such a directories in my miA2Lite phone.
Thus, I typed fastboot boot "/sdcard/twrp-3.5.2_9-2-daisy-unofficial.img"
* /sdcard is the root of <internal storage> directory.
** On Windows, double quote the address, if it's include spaces.
Click to expand...
Click to collapse
The twrp image was on my pc(linux) i was booting directly from pc's terminal. And if you use only adb(or fastboot) then the paths are pc's absolute paths.