Hello,
I have a moto G100 I just purchased. I unlocked the bootloader and I tried to install LineageOS but it was being difficult. I could get it to boot into TWRP. Now I tried to restore everything to stock as it wasn't even booting. After flashing the rom back in via fastboot the unit shows up as a serial device but that's it, no picture on the screen or anything.
I need some help to get this working again. Besides the directions on the LineageOS page sucks, steps are missing and things do not work properly.
Any help would be appreciated.
This is Qualcomm HS-USB QDLoader 9008 mode and won't boot.
Can anyone please help so this won't take weeks or months?
Thanks
Hello,
I fixed the brick with the blankflash file blankflash_nio_RRTS31.Q1-84-24-3-6
I was able to then use the official tool to recover the firmware. I was able to get LineageOS working but I wasn't able to do TWRP at all properly.
So I managed to install twrp but couldn't install lineage or anything out of it...
I managed to get TWRP installed but it was essentially useless as I couldn't access the internal flash unless it was setup by the OS already if you format the internal flash storage with TWRP it's useless especially via MTP.
I was able to install LineageOS and I was able to boot it, but I don't understand why it says I do not have enough space to install gapps. Without gapps LineageOS is essentially useless as an OS unless you do not use anything from google at all whatsoever not eve maps or anything.
How do I fix it so I can install gapps? I can't resize the system partition via TWRP as it doesn't even show it.
Thanks
if you have the bootloader unlocked you can try the "tinyflashscript" way and use that to overwrite all partitions with a stock image found here
RET stands for Retail and than the region code follows, just download the latest one for your region
after that your partitions are reset to the start and you could keep it that way or attempt to install lineage again but clean this time
I ran into the exact same situation as you with the storage issues and this fixed it for me
Hello my G100 was fully hard bricked trying to installed LineageOS (not the modded). I followed the following steps:
1. Installed and booted into LineageOS recovery from electimon.
2. Factory reset
3. Install ROM as adb sideload.
However, installation stuck at 47% and aborted. Phone was hard bricked once turned off. It couldn't even boot into booloader.
Luckily, I was able to enter EDL mode by pressing and holding volume and power down together for some time while it was plugged into PC using usb. Then I used blankflash to restore. This saved me from taking it to repair centre.
Hello,
I had the same brick issue and blankflash fixed it for me. I will try writing stock again then install LOSRecovery again and then try sideloading both LineageOS and gapps but I don't think that will work correctly as I think I did try that but we shall see, last time I did an install though after fixing the brick issue I used fastboot to do the stock recovery which should have fixed the partition sizes...
Thanks
It's strange that device becomes hard bricked because I installed LineageOS before and it booted fine. Only thing now changed is that I'm using February stock ROM instead of December one. Did Motorola change anything in Feb update that would cause hard brick when trying to install custom ROM?
Also, I've never did the "Ensuring all firmware partitions are consistent" thing. It worked before but not sure if we need to do it now.
Hello,
Strange indeed I can get LineageOS installed BUT because this is an A/B phone which is so silly, I can't install Gapps into LineageOS so essentially useless as the installer says the partition is too small and I do not have a way to fix that at the moment.
Thanks, and blankflash was able to get me up and running on stock but I cannot use the phone yet just like the DooGee S95 Pro I bought in hopes to use LineageOS... long story. Stuck with my ZTE Axon 7 from 2016 and a crap phone to make calls since my provider killed service to my ZTE Axon 7 so I carry basically 3 phones now. Until there is a fully working TWRP I am essentially screwed and feel like I wasted $400 on another phone.
marcusah123 said:
Hello,
Strange indeed I can get LineageOS installed BUT because this is an A/B phone which is so silly, I can't install Gapps into LineageOS so essentially useless as the installer says the partition is too small and I do not have a way to fix that at the moment.
Thanks, and blankflash was able to get me up and running on stock but I cannot use the phone yet just like the DooGee S95 Pro I bought in hopes to use LineageOS... long story. Stuck with my ZTE Axon 7 from 2016 and a crap phone to make calls since my provider killed service to my ZTE Axon 7 so I carry basically 3 phones now. Until there is a fully working TWRP I am essentially screwed and feel like I wasted $400 on another phone.
Click to expand...
Click to collapse
Using the method I described above I was able to install Lineageos 19.1 and then gapps (mindthegapps) using lineage recovery. it should be entirely possible
Hello,
With the storage not being large enough I was trying to install openGapps ( stock size ) for Android 11 since I was trying to use Lineage 18.1 and not 19/19.1 since 19/19.1 appear to have bugs and 18.1 does not. Anyhow I tried to sideload openGapps and it said there wasn't enough space on the system partition. I suppose I should try mindthegapps instead.
Thanks
So anyone successfully installed it without causing hardbrick? What exact steps did u follow? r u using g100 or edge s and what is the build number of stock rom prior to install? thanks
Windoors said:
So anyone successfully installed it without causing hardbrick? What exact steps did u follow? r u using g100 or edge s and what is the build number of stock rom prior to install? thanks
Click to expand...
Click to collapse
I used the latest stock after doing a recovery with blankflash and the rescue utility from Motorola. I then installed LOSrecovery because TWRP isn't ready. I then booted into LOSrecovery and sideloaded 19.1 latest from this forum. I can't figure out how to resize /system correctly so I cannot install anything other than MindTheGapps which sucks a lot.
Anyhow if we get a working TWRP soon that will allow resize as TWRP can't show the system partition and A/B switching is being worked out then we will be good to go.
If this isn't helpful or you need exact commands then I can do that too for you.
Related
Hey everyone,
i usually don't post questions but i've been on pretty much every forum the web has to offer and am still stuck so i'll try my luck here.
i'm currently running lineage 7.1 on my mi4c, i've used another phone for a while but now that my mi4c has a new battery i wanted to start using it again, is also decided this would be the time to update it to android oreo or pie, this however seems to be impossible.
i can only use twrp up to 3.1.1.1, all higher (and unofficial versions) will not boot via fastboot 'dtb not found' or when flashed via older twrp will freeze on boot screen.
whenever i try to install a new rom it tells me 'error code 7', when i remove the 'assert' lines in the update it gives me 'error code 6'
my device is unlocked, i have checked this in fastboot.
do i have to install miui again before installing another rom? do i have to go back to the standard recovery? i'm currently running out of ideas and hope you guys might be able to help me. maybe i'm overlooking something simple.
kind regards,
Monstreys
Hi! I don't know if this is a coincidence or not, but I was about to start a similar thread.
I try to do exactly what you are doing. I want to install LineageOS 16, unofficial ROM.
For this you need a newer TWRP, like 3.2.3.0, but it doesn't work 'dtb not found' like you said. I found out that this doesn't work because you need to have nougat bootloader. Most probably you have lollipop bootloader like I have, and thats why newer versions of TWRP are not working. I think the only way to update your bootloader to a nougat one is to flash the latest MIUI ROM. But, unfortunately, when you do that the bootloader gets locked, and I can't unlock it via MiUnlock due to Error:20091 when I try to link the phone to the Mi account. In MiUnlock it gives me the "this account cannot unlock the phone" or something like that.
Now I removed the "assert" lines from my rom and flashed it without the error 7 or 6. Some error still apears, but it also apears when I flash LineageOS 14.1, and that version is working even with those 2 errors I can't remember during flash.
After I flashed LineageOS, I flashed gapps and then superSU, and now my mi4c is stuck on mi logo for about 20 minutes, and I think it will remain that way.
So, there are 2 things we need to solve. We need to find a way to install latest MIUI without relocking the bootloader because I can't unlock it via MiUnlock, or to find out why after I flashed LineageOS 16 it gets stuck on MI logo.
I think I found the solution. Do exactly what this guy is doing here and it might work.
https://forum.xda-developers.com/showpost.php?p=78640737&postcount=63
I followed that guy instructions and I managed to install TWRP 3.2.3.0 and LineageOS 16, and it booted. Now I am at the setup part but it has very big lag...
makaveli97 said:
I think I found the solution. Do exactly what this guy is doing here and it might work.
https://forum.xda-developers.com/showpost.php?p=78640737&postcount=63
I followed that guy instructions and I managed to install TWRP 3.2.3.0 and LineageOS 16, and it booted. Now I am at the setup part but it has very big lag...
Click to expand...
Click to collapse
i
i was unable to install the patch file, this nonetheless fixed my problem, thanks!!
if above not working, another method to do it based on my method.
https://forum.xda-developers.com/showpost.php?p=81573941&postcount=199
makaveli97 said:
I think I found the solution. Do exactly what this guy is doing here and it might work.
https://forum.xda-developers.com/showpost.php?p=78640737&postcount=63
I followed that guy instructions and I managed to install TWRP 3.2.3.0 and LineageOS 16, and it booted. Now I am at the setup part but it has very big lag...
Click to expand...
Click to collapse
My MI4C has been successfully flushed into lineage-17.1-20200220-UNOFFICIAL-libra.zip. It has been updated on TWRP 3.1.1 and keeps reporting error 7, and then abandoned TWRP3.1.1 and flashed into OrangeFox-R10.0-1-Stable-libra.zip After brushing libra-aqua_firmware_7.2.9.zip on this REC, you can flash lineage-17.1. I do n’t think it will be impossible to refresh because of partition problems. If you only need to upgrade lineage-17.1, you can refer to this method.:good::good:（Translation is not easy to use）
celrau said:
There is a 3.2.x around. If you don't want to bother go in the zip, /META-INF/com/google/android/ and delete the first lines (the ones starting with "assert") from updater-script, save and flash again.
Click to expand...
Click to collapse
rianawirawan said:
Right now, i'm using 3.1.1 -1 btw
It's latest twrp ver from official
Click to expand...
Click to collapse
TWRP-20190418-3.3.0.0-libra.img for the Xiaomi Mi 4c, by GuaiYiHu :
https://androidfilehost.com/?fid=1395089523397945946
Latest firmware for the Xiaomi Mi 4c libra :
https://github.com/XiaomiFirmwareUp...iui_MI4c_V10.1.1.0.NXKCNFI_13b9b312d0_7.0.zip
Hi everyone, I'm new to this forum, I have been going crazy with a Huawei P8 Lite 2017 for two days, I was trying to install DarkJoker360's AOSP 11 I have already modded a P8 Lite (not 2017) and I had no problems, I managed to install TWRP recovery 3.2.1-0 (I can't find the recovery that DarkJoker recommends) via ADB on my Windows PC I did all the necessary wipes and tried to install this operating system in the partition (Image System) it is an .img file after doing this I restarted and the only thing it does is bring out the Android writing, as if it had installed the rom but then it ends up restarting after a few seconds of this writing, without even getting to the configuration screen, what could I have mistaken?
I apologize for any mistakes but I'm Italian and I might have something wrong
Chricap said:
Hi everyone, I'm new to this forum, I have been going crazy with a Huawei P8 Lite 2017 for two days, I was trying to install DarkJoker360's AOSP 11 I have already modded a P8 Lite (not 2017) and I had no problems, I managed to install TWRP recovery 3.2.1-0 (I can't find the recovery that DarkJoker recommends) via ADB on my Windows PC I did all the necessary wipes and tried to install this operating system in the partition (Image System) it is an .img file after doing this I restarted and the only thing it does is bring out the Android writing, as if it had installed the rom but then it ends up restarting after a few seconds of this writing, without even getting to the configuration screen, what could I have mistaken?
I apologize for any mistakes but I'm Italian and I might have something wrong
Click to expand...
Click to collapse
I thought huawei doesn't allow bootloader to be unlocked this proves Me wrong
Austinredstoner said:
I thought huawei doesn't allow bootloader to be unlocked this proves Me wrong
Click to expand...
Click to collapse
I unlocked the bootloader via "DC-Unlocker" so I don't think that's the problem
Chricap said:
I unlocked the bootloader via "DC-Unlocker" so I don't think that's the problem
Click to expand...
Click to collapse
If u still have twrp installed after flashing that custom Rom u can try flashing other custom rom like lineage os
Before flashing anything else try to make sure what your doing 1 mistake could make u ruined like forever if u flashed other custom rom still in bootloop but TWRP uninstalled well than your screwed
Austinredstoner said:
If u still have twrp installed after flashing that custom Rom u can try flashing other custom rom like lineage os
Before flashing anything else try to make sure what your doing 1 mistake could make u ruined like forever if u flashed other custom rom still in bootloop but TWRP uninstalled well than your screwed
Click to expand...
Click to collapse
Yes, I still have the TWRP installed, precisely version 3.4.0-0, since I could not find a working ROM I tried to debrand it (it was brand Tim) and I think I have done a damage to follow that guide, now I do not not even install the stock rom anymore. I don't know what to do at this point, I would leave the custom rom alone and reinstall its stock rom, at least debrand ...
Hello,
I have the G100 and I want to know how I can install TWRP where it actually works not just sitting on the boot screen, it's flashing or intermittently working and I don't get it. Once this is done I can then get LineageOS as my main OS on the device which would be nice since installing gapps is a pain without TWRP.
Thanks
Hi, I did something stupid and need some help please.
I got the bootloader unlock code for my KB2007 - Unlock went well, no issues.
Then I proceeded to download and install the latest official TWRP - Also no issues, I was in the custom recovery, created some backups etc.
After that, I followed the instructions to install Lineage OS as posted here:
Install LineageOS on kebab | LineageOS Wiki
wiki.lineageos.org
I flashed the dtbo and vbmeta partitions as instructed and proceeded with adb sideloading the copy-partitions-20220613-signed.zip file - Somewhere around here is where things went south.
I was not able to access/read my data partition anymore, and attempted to flash the lineage-recovery. After a reboot, I'm now stuck in the bootloader (fastboot). When I select Recovery mode, the phone just goes black. I also can no longer "fastboot boot twrp.img" - Error: "Failed to load/authenticate boot image: Load Error".
After checking the guide one more time I noticed it says the device has to be on Android 12, which mine was not (it was still in factory condition - Android 11). So that was likely the problem.
So now the big question is can I recover from this state? If yes, what's the best way to do so?
Thanks so much!
FreeDee said:
Hi, I did something stupid and need some help please.
I got the bootloader unlock code for my KB2007 - Unlock went well, no issues.
Then I proceeded to download and install the latest official TWRP - Also no issues, I was in the custom recovery, created some backups etc.
After that, I followed the instructions to install Lineage OS as posted here:
Install LineageOS on kebab | LineageOS Wiki
wiki.lineageos.org
I flashed the dtbo and vbmeta partitions as instructed and proceeded with adb sideloading the copy-partitions-20220613-signed.zip file - Somewhere around here is where things went south.
I was not able to access/read my data partition anymore, and attempted to flash the lineage-recovery. After a reboot, I'm now stuck in the bootloader (fastboot). When I select Recovery mode, the phone just goes black. I also can no longer "fastboot boot twrp.img" - Error: "Failed to load/authenticate boot image: Load Error".
After checking the guide one more time I noticed it says the device has to be on Android 12, which mine was not (it was still in factory condition - Android 11). So that was likely the problem.
So now the big question is can I recover from this state? If yes, what's the best way to do so?
Thanks so much!
Click to expand...
Click to collapse
Restore to stock via MSM.
You must update to OxygenOS 12 before installing lineageos 19.1 or you will brick.
The lineagsos guide is wrong and I bricked my device by following it too.
For now, you can only unbrick it with msmtool.
[OP8T][OOS TMO KB09CB] Unbrick tool to restore your device to OxygenOS
Disclaimer: By attempting any of the processes listed in this thread you accept full responsibility for your actions. I will not be held responsible if your device stops working, catches fire, or turns into a hipster and claims to have been...
forum.xda-developers.com
Then OTA to OOS 12, then install LOS19.1.
Thanks guys! I was able to restore the device using the MSM tool
I intend to keep it on OOS 11 (and potentially flash LOS18.1), because KB2007 is the T-Mobile variant and based on what I read dual sim only works with OOS 11.
The problem is it is becoming increasingly difficult to find instructions (or even downloads) for anything but the very latest versions :/
FreeDee said:
Thanks guys! I was able to restore the device using the MSM tool
I intend to keep it on OOS 11 (and potentially flash LOS18.1), because KB2007 is the T-Mobile variant and based on what I read dual sim only works with OOS 11.
The problem is it is becoming increasingly difficult to find instructions (or even downloads) for anything but the very latest versions :/
Click to expand...
Click to collapse
You can also use KB2007 OOS 13 beta 1 which works with dual sims.
Rootk1t said:
You can also use KB2007 OOS 13 beta 1 which works with dual sims.
Click to expand...
Click to collapse
Thanks! Yeah, I also read about that, and it does indeed sound like a potential way to go.
Do you know if anyone has figured out yet what makes this "beta 1" special in that it allows dual sims? I think I also read it's no longer possible with beta 2.
FreeDee said:
Do you know if anyone has figured out yet what makes this "beta 1" special in that it allows dual sims? I think I also read it's no longer possible with beta 2.
Click to expand...
Click to collapse
As far as i know, it's still unknown what makes beta 1 work in dual-sim mode.
Hi All,
I have a new-to-me Oneplus 7 Pro. I have been trying to get Lineage with MicroG running. Well it has been quite the adventure and I have it to the point where I have Lineage running fine, and go to reflash TWRP and have bricked the phone, which takes a bit of time to get back to the point of having Linage running again. Specifics:
Lineage version: lineage-19.1-20221219-microG-guacamole.zip
TWRP Versions: I have found that twrp-3.6.1_11-0-guacamole.img works since my phone is at Android 11.
My questions are:
Are TWRP versions tied to Android versions?
When I am trying to get the last version of TWRP installed I have tried 2 approaches:
fastboot flash recovery
fastboot flash boot
Neither worked, phone always ends up bricked. I have used:
TWRP-3.5.1-guacamole-Nebrassy-3.img
twrp-3.6.1_11-0-guacamole.img
twrp-3.6.2_11-0-guacamole.img
I also have tried to boot the images 1st using: fastboot boot twrp-3.6.1_11-0-guacamole.img
and that bricks things.
What am I doing wrong?
Thanks
Ray
rbahr said:
Hi All,
I have a new-to-me Oneplus 7 Pro. I have been trying to get Lineage with MicroG running. Well it has been quite the adventure and I have it to the point where I have Lineage running fine, and go to reflash TWRP and have bricked the phone, which takes a bit of time to get back to the point of having Linage running again. Specifics:
Lineage version: lineage-19.1-20221219-microG-guacamole.zip
TWRP Versions: I have found that twrp-3.6.1_11-0-guacamole.img works since my phone is at Android 11.
My questions are:
Are TWRP versions tied to Android versions?
When I am trying to get the last version of TWRP installed I have tried 2 approaches:
fastboot flash recovery
fastboot flash boot
Neither worked, phone always ends up bricked. I have used:
TWRP-3.5.1-guacamole-Nebrassy-3.img
twrp-3.6.1_11-0-guacamole.img
twrp-3.6.2_11-0-guacamole.img
I also have tried to boot the images 1st using: fastboot boot twrp-3.6.1_11-0-guacamole.img
and that bricks things.
What am I doing wrong?
Thanks
Ray
Click to expand...
Click to collapse
If you look at the official installation page for your phone, you will see that Lineage OS 20 and 19.1 are supported. So you should reinstall Lineage OS 18.1 again, and then follow the steps on this page. Don't bother reinstalling GAPPS until after you upgrade it.
If for whatever reason you don't want an Android version higher than 11, let me know.
I specifically don't want GAPPS or anything remotely Google related. I had tried OS 20 and found that I had a problem installing apps - probably user error, but I don't need the latest and greatest. I am currently at Android 11.
I will read through the instructions, although the number of tutorials I have gone through is craze.
Can you tell me what the relationship between TWRP and Android version is, and are you able to sus out what I did wrong with my efforts to get TWRP loaded over the lineage 19 version I was using?
Thanks
Ray
rbahr said:
I specifically don't want GAPPS or anything remotely Google related. I had tried OS 20 and found that I had a problem installing apps - probably user error, but I don't need the latest and greatest. I am currently at Android 11.
I will read through the instructions, although the number of tutorials I have gone through is craze.
Can you tell me what the relationship between TWRP and Android version is, and are you able to sus out what I did wrong with my efforts to get TWRP loaded over the lineage 19 version I was using?
Thanks
Ray
Click to expand...
Click to collapse
rbahr said:
I have been trying to get Lineage with MicroG running
Click to expand...
Click to collapse
So I guess you don't want GAPPS, just MicroG. Definitely read through the instructions I gave you, as they are the official installation and upgrade instructions.
I would recommend installing Lineage OS 20, because it is the version that is being maintained right now.
I will attempt to guide you through the steps, but I need to know what your situation is right now: Is your bootloader unlocked? What OS do you have installed right now? What recovery are you using? etc.
I appreciate your help. Currently I am looking at a freshly updated phone with Android 11, and Oxygen 11.0.9.1.GM21AA.
The phone is a GM1917
Bootloader is unlocked and I am in developer mode. I have adb and fastboot loaded on my computer. I also have a working version of msm as I have bricked this thing 6 or 7 times...
Several times now, I have done the following:
Install TWRP
Install Lineage
Try and reflash TWRP <-- consistently fails at this point, gets stuck in a boot loop in the bootloader screen
Thanks
Ray
rbahr said:
I appreciate your help. Currently I am looking at a freshly updated phone with Android 11, and Oxygen 11.0.9.1.GM21AA.
The phone is a GM1917
Bootloader is unlocked and I am in developer mode. I have adb and fastboot loaded on my computer. I also have a working version of msm as I have bricked this thing 6 or 7 times...
Several times now, I have done the following:
Install TWRP
Install Lineage
Try and reflash TWRP <-- consistently fails at this point, gets stuck in a boot loop in the bootloader screen
Thanks
Ray
Click to expand...
Click to collapse
"Try and reflash TWRP" what do you mean, update the OS over TWRP?
I mean trying to re-install TWRP after installing Lineage
rbahr said:
I mean trying to re-install TWRP after installing Lineage
Click to expand...
Click to collapse
OK. Can you try following the installation instructions and skip the unlock bootloader step? Do so at your own risk, because the steps say you have to be on Android 12 first. If you do follow them, just make sure you follow them very carefully.
rbahr said:
I mean trying to re-install TWRP after installing Lineage
Click to expand...
Click to collapse
To my knowledge the guides that are provided on the TWRP site don't work for Android 12 and 13. From what I've heard, you have to root your phone and then install TWRP through Magisk.
Honkette1738 said:
To my knowledge the guides that are provided on the TWRP site don't work for Android 12 and 13. From what I've heard, you have to root your phone and then install TWRP through Magisk.
Click to expand...
Click to collapse
The guides I linked to point to the official Lineage OS instructions, right?
ethical_haquer said:
The guides I linked to point to the official Lineage OS instructions, right?
Click to expand...
Click to collapse
Yeah, but I was just saying how they should probably reflash TWRP instead of how TWRP's site says to, which doesn't work
Honkette1738 said:
Yeah, but I was just saying how they should probably reflash TWRP instead of how TWRP's site says to, which doesn't work
Click to expand...
Click to collapse
This build uses Lineage OS Recovery instead of TWRP.
ethical_haquer said:
This build uses Lineage OS Recovery instead of TWRP.
Click to expand...
Click to collapse
I know, but TWRP can be installed with Android 13 custom roms according to the TWRP thread.