So anywone with the newest G91 Max phone.
Device: Blu g91 max g0690ww
I couldn't find any info on rooting this since it's so new. So here is how I did it:
Here's the firmware link in case you wanted to patch the boot file yourself. But I'm including it already patched for convenience.
Blu_G91_Max_G0690WW_MT6785_V11.0.03.01_Generic_211222
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
**Your phone will be erased and warranty void**
Download Magisk patched boot file:
magisk_patched-24301_6WKnK.img - shared with FileRun
bananaspider.com
Place file in your fastboot folder.
Under Developer Options of phone, turn USB debugging ON, turn OEM unlocking ON.
Boot to Fastboot mode: hold volume up, down and power until phone screen turns off. Release power until text on screen. Use the up volume to select Fastboot mode and down volume to choose it.
Now that you are in fastboot mode, plug phone into computer and: (I'm using Linux)
Open command or terminal from your Fastboot folder:
[email protected]:~/Downloads/platform-tools$ fastboot devices
1010305022004085 fastboot
[email protected]:~/Downloads/platform-tools$ fastboot flashing unlock
(bootloader) Start unlock flow
OKAY [ 43.978s]
Finished. Total time: 43.978s
[email protected]:~/Downloads/platform-tools$ fastboot flash boot magisk_patched-24301_6WKnK.img
Sending 'boot_a' (32768 KB) OKAY [ 1.056s]
Writing 'boot_a' OKAY [ 0.081s]
Finished. Total time: 1.154s
[email protected]:~/Downloads/platform-tools$ fastboot reboot
Rebooting OKAY [ 0.003s]
Finished. Total time: 0.204s
Once booted, Check Magisk for root.
**DEVS! Any ROM support here?
First of all, thank you! I was successful after following your instructions.
Unfortunately, my sim card is no longer being recognized. Did you have any issues with this?
Hey thanks a lot good to know it helps somebody. no issues with the SIM card so far. I'm using mint mobile SIM.
jasonbiggs said:
Hey thanks a lot good to know it helps somebody. no issues with the SIM card so far. I'm using mint mobile SIM.
Click to expand...
Click to collapse
I am using T-Mobile and it was working at first but then after I restarted the phone it stopped working. All the options for mobile network are grayed out. I tried factory resetting and doing everything over again with the same result. I also verified that it is not the SIM Card. I am at a loss here. I also re-locked the boot loader, which led to a boot loop but I was able to get the phone back into fastboot mode and fixed that. I'm going to try to flash the stock image and see if it helps.
Yes I flashed the stock image just to see if I could and it worked flawlessly maybe that'll help you out good luck.
jasonbiggs said:
Yes I flashed the stock image just to see if I could and it worked flawlessly maybe that'll help you out good luck.
Click to expand...
Click to collapse
Thank you. I didn't actually end up flashing the stock image yet, but I did do a factory reset again and then I left the house for about 30 mins and had left it on the setup screen at home. When I came back the sim card and mobile data were working, so perhaps it just needed some time to connect or what not.
z0ne_tripper said:
I am using T-Mobile and it was working at first but then after I restarted the phone it stopped working. All the options for mobile network are grayed out. I tried factory resetting and doing everything over again with the same result. I also verified that it is not the SIM Card. I am at a loss here. I also re-locked the boot loader, which led to a boot loop but I was able to get the phone back into fastboot mode and fixed that. I'm going to try to flash the stock image and see if it helps.
Click to expand...
Click to collapse
you probably aren't using the correct boot img. Did you use the one provided, or did you root it yourself?
dtingley11222 said:
you probably aren't using the correct boot img. Did you use the one provided, or did you root it yourself?
Click to expand...
Click to collapse
I used the one provided and after that I also patched one myself to see if there was a difference in the very beginning, but it was the same problem. All I had to do was wait about 30 mins and it worked just fine.
z0ne_tripper said:
I used the one provided and after that I also patched one myself to see if there was a difference in the very beginning, but it was the same problem. All I had to do was wait about 30 mins and it worked just fine.
Click to expand...
Click to collapse
oh ok cool
@jasonbiggs there probably is multiple gsis that are available for the phone. search phh gsi or andy yan gsi for lineage.
Any help with Blu S91 Pro? Can’t find firmware download anywhere.
Hey Jasonbiggs I have a BLU G91 MAX but in the developer optimazion when I first got it in the developer options they dynamic system updates so I installed when it said restart to finish installing my dynamic system update when it went to reboot the blu sigh came up but in small whit letters next to it say your phone's corrupted press power button within 5s to continue booting but then my auto rotate wouldn't work and a bunch of other features so I researched and sone1 said unlock the bootloader which I did with an OTG cable and 2 phones using the bugjaeger app and I have to leave my bootloader unlocked because if I close then alot of my apps won't work even tho i don't have a computer I disabled dynamic system updates but it still has the corrupt file and the only way to get rid of that is with a PC but since bootloader is unlocked I was just gonna root it with a better gaming ROM but idk how to that but sorry for the long message but I downloaded your page with the steps to the bootloader thing that is helping people so I was ted what do you think should cause I never closed my bootloader so please anything would be helpful
Related
Hello everybody
It seems I'm quite late with this issue so I wasn't sure whether to post in an old thread or open a new one...
A few days ago my 12-year-old nephew, for 3 month a really proud owner of a Nexus S I9023 came to me desperately sad: He had tried to update to ICS (the manual "update.zip method") and ended up with a totally unresponsive phone like many others back in December.
I do not own an Android device myself and this stuff is all new to me (so sorry for any dumb questions or thoughts ;-) ), but after some googling and finding this great forum and especially AdamOutler's tool (and reading about other people's success with it) I was confident to be able to bring the Nexus back to life. But I'm still stuck at a certain point...
What I've done so far:
-I installed Ubuntu 10.04.3 LTS natively on a PC (I failed with using a virtual installation on my Mac).
-Installed JavaSDK and the UnBrickable Resurrector.
-Downloaded the Android SDK from here and installed it following this advice (I didn't download fastboot separately as it was included in the SDK).
-Downloaded a full ROM from here , extracted the bootloader.img and boot.img from the .zip, downloaded recovery-clockwork-5.0.2.0-crespo.img and put all that stuff in the fastboot directory.
Ok, ready to go now (I think):
I start the Resurrector (R40), select "Nexus S", remove the battery, plug in USB, replace the battery (now the Resurrector recognizes the Nexus) and click "Perform Resurrection" (without holding any button on the Nexus). After a few seconds the Resurrector reports success, showing the "Android with speech bubble" and saying "Fastboot mode" below. On the Nexus the Search- and Homebutton (the both on the right side) are now lit-up, but the display is still black.
At this point I'm wondering if everything went ok, shouldn't the Nexus now already show its bootloader screen like on Adam's image or the battery charging screen ? Anyway, according to the Resurrector everything is fine, so let's continue.
I start Terminal and cd to the fastboot directory. Just to be sure the Nexus is recognized:
Code:
lsusb
Bus 002 Device 023: ID 18d1:4e20
Code:
fastboot devices
34329EB4B3F800EC fastboot
Now I'm not exactly sure what to do next. As far as I've understood some have now flashed the bootloader, boot & recovery images first, others have "booted from the recovery.img (?)", in both cases I end up with this:
Code:
fastboot flash bootloader bootloader.img
sending 'bootloader' (1536 KB)...
OKAY [ 1.629s]
writing 'bootloader'...
FAILED (remote: Bootloader Locked - Use "fastboot oem unlock" to Unlock)
finished. total time: 1.631s
Code:
fastboot boot recovery-clockwork-5.0.2.0-crespo.img
downloading 'boot.img'...
OKAY [ 4.374s]
booting...
FAILED (remote: Bootloader Locked - Use "fastboot oem unlock" to Unlock)
finished. total time: 4.376s
But when I try to unlock, I only see this:
Code:
fastboot oem unlock
...
I wait several minutes but nothing happens. I stop this by unplugging the phone and an error appears:
Code:
FAILED (status read failed (No such device))
finished. total time: 561.710s
(I assume waiting nearly 10min is enough?)
I also tried to run fastboot as root with sudo, but that doesn't change anything. I'm really stranded at this point. :-(
This is my first contact with Android and I'm also not very familiar with Linux, but in my humble understanding I should be just one little step away from success, shouldn't I?
For me everything seems to work properly, the Resurrector reports success, saying the Nexus is in fastboot mode now, fastboot is running and recognizing it and also my attempts to "fastboot flash" or "fastboot boot" obviously work until the "Bootloader Locked" error pops up.
So the two big questions are:
1. Is it ok that after successful resurrection only Search and Home are lit-up, but the display remains black or should I see the bootloader or battery charging screen?
2. Why is fastboot stuck while unlocking?
I'm also wondering if it's worth it to set up a Linux/Windows dualboot installation to run fastboot or even Odin in Windows, I can't imagine that I have a better chance that way, this should work with Linux alone, shouldn't it?!
So, I hope I haven't bored you too much ;-)
I would really appreciate some help to make my nephew happy again...
Have a nice weekend!
If the bootloader is locked then you need to OEM unlock then on the screen it should say unlock bootloader? I need to press up with the volume keys and press ok power button.. Then it should be unlocked try that then white everything yo the phone
Sent from my Nexus S 4G using xda premium
In order to unlock oem, you first need to fastboot unlock which you did.
Then, confirm it on your phone which you didn't b/c you can't see/don't have fastboot screen.
And i think you didn't have fastboot screen b/c you didn't hold the buttons like you supposed to.
That's what everyone has to do to enter fastboot.
I think you should follow this thread.
And download and use the ROM package he has linked.
And instead of ODIN which requires Windows, you can use Heimdall which can run on Linux/Mac.
And search how to use Heimdall before flashing.
And if you don't have a backup, download some ROM (stock one preferred) to flash instead of restoring backup.
Also, search how to flash a ROM and clean/full wipe in CWM before flashing.
Same situation here, please help me.
Hello Cicofz and everybody,
I am stuck in about the same situation. Only a little later, my phone bricked on a 4.0.4 upgrade.
I used resurrection and on my phone the same Search and Home lit-up, the display remains black! but resurrection tells me it is in download or Fastboot mode. My fastboot on Mac doesn't get stuck, it tells me everything is Oke. However there is no possibility to get the screen on and really start fastboot on my phone...
So i think I'm stuck on the same thing you got stuck on some weeks ago.
Did you solve the problems in the meanwhile? If so can you please let me know how you did this.
If anybody els can help me please Do...
regards KnoefKnoef
Hello KnoefKnoef,
yes, I was able to bring the Nexus back to life (and a big grin back on my nephew's face) ;-) Afterwards it turned out pretty easy, just fastboot with Ubuntu, no need for any Windows stuff.
It's getting late here in Germany, so I'll try to recall and post what I've done tomorrow. I'm not sure, but I think I've even copied the whole terminal session so I can tell you step by step. I must have a look at the PC I used for it tomorrow...
Good Night
It is running... and yes it is on ICS 4.0.4.
thanks for your Quick reply, butt help is not needed anymore.
After using UnBrickable Resurrector in Linux I got the phone in download mode. with the home and search light glowing.
Then I Switched to Windows using this tread: *OFFICIAL* Android 4.0.4 IMM76D ROM for Nexus S 4G http://forum.xda-developers.com/showthread.php?t=1575502
It ended in a message Failed. Butt the phone was reboot-able. And best of all it is running on ICS 4.0.4.
So I'm very happy now.
It was quite a procedure doing all this on a MAC using Windows and Linux. Butt I eventually managed to do it....
Thanks for your input...
knoefknoef said:
thanks for your Quick reply, butt help is not needed anymore.
Click to expand...
Click to collapse
Pleased to hear that
Hi,
I've never changed anything on my transformer as far as custom roms, never gained root, never even previously booted into the stock recovery. But after one night i woke up to my tablet being burning hot while it was charging. Further investigation showed that it was just rebooting over and over.
I turned it off. left it off to cool down, turned it on.
Bootloop.
I then downloaded the asus firmware put it on an SD card and followed the steps for installing it through asus recovery.
Bootloop.
I can't seem to find a guide on how to actually get nvflash going which is how i'd assume i should fix this.
By the way, I killed my warranty 6 months ago when my girlfriend stood on my tablet (it was on the bed and she walked on the bed in shoes/heels) and cracked the screen. It's been running fine and when it's on it's not noticible. But obviously without the warranty i'm kind of ****ed for an issue that probably Asus did cause.
This actually happened a few weeks ago but my last effort to fix it went south and i haven't thought about it for a while but now i was thinking of taking another crack at it again..
Short question (TL;DR):
Can someone link me a good guide to get nvflash to put either a better recovery or a new non-corrupt rom on my tablet?
Update1: Okay so people here confirm that I have fastboot enabled. But i don't understand how to use it. I've installed the fastboot driver. I've below posted what outputs when i try to push a CWM recovery to it (it looks fine but doesn't seem to work?).
If anyone has some links to how to use any tools via fastboot or APX to recover from here that would be good. Even if you just want me to dump information just tell me how and i'll run anything.
Update2: This time i found out that the fastboot icon is visible to anyone with JB. But fastboot isn't unlocked unless you run the asus apk. So I do not actually have fastboot enabled. Which explains the strange behaviour below.
Because even after trying to install asus official firmwares from SD card and failing, the only alternative remaining is to send it back to asus.
well you need to get it to boot in order to unlock.
perhaps follow the downgrade instructions in general?
lafester said:
well you need to get it to boot in order to unlock.
perhaps follow the downgrade instructions in general?
Click to expand...
Click to collapse
That resulted in a dead android with a red exclaimation mark from his chest cavity.
No dice.
Any other ideas?
Edit: There's a newer version than the one which is on my device, but updating causes it also to die Stupid triangle of death.
I've got 4 options in the pre-boot stuff; which is RCK Android USB and Wipe Data. None of these seem helpful, i was hoping there might be a way to push across using adb but i guess that requires root beforehand.
skythra said:
I've got 4 options in the pre-boot stuff; which is RCK Android USB and Wipe Data. None of these seem helpful, i was hoping there might be a way to push across using adb but i guess that requires root beforehand.
Click to expand...
Click to collapse
If the USB option is available, that should mean your tablet is unlocked and you can use fastboot from your PC to flash a custom recovery.
_that said:
If the USB option is available, that should mean your tablet is unlocked and you can use fastboot from your PC to flash a custom recovery.
Click to expand...
Click to collapse
Okay, that's odd, well so this is a good thing for me then. I can just follow one of the guides here for pushing a firmware onto it? Can you recommend one?
My understanding is i need to get ADB to work by installing the google tools and then install the ADB driver and something something.. I'm going to go read up now about that and pray to my favourite diety of the minute. I assume there should be one for electronics..
Okay so,
using fastboot, installing the drivers and etc. I tried to flash a custom recovery, but so far it doesn't look like it worked; here's the output:
C:\Users\X\Desktop\Android Tools\platform-tools>fastboot -i 0x0B05 reboot
rebooting...
finished. total time: 0.552s
C:\Users\X\Desktop\Android Tools\platform-tools>fastboot -i 0x0B05 flash rec
overy recovery-jb-touch.img
sending 'recovery' (6866 KB)...
OKAY [ 0.867s]
writing 'recovery'...
OKAY [ 0.069s]
finished. total time: 0.944s
C:\Users\X\Desktop\Android Tools\platform-tools>fastboot -i 0x0B05 reboot
rebooting...
It doesn't reboot my tablet at all. It doesn't load the recovery from any form of way i can tell. I'm at a loss again. I still can't find a guide to use fastboot to send any kind of stock firmware or custom firmware to the tablet reliably either. So i'd like any tips/links etc please
Okay so i'm still struggling to do this alone with tidbits strewn across the internet. Every time i think i find new information I find that I can't follow the directions because something else prevents me. Having 'fastboot' hasn't really helped me at all yet.
So i found http://android.stackexchange.com/questions/28077/bricked-my-asus-tf300t-manual-jb-update and i was using that but i'm still finding odd behaviour with fastboot.
Let me explain in copy-paste form.
C:\Users\Skythra\Desktop\Android\platform-tools>fastboot devices
???????????? fastboot
C:\Users\Skythra\Desktop\Android\platform-tools>fastboot devices
015d262e990c0c08 fastboot
C:\Users\Skythra\Desktop\Android\platform-tools>fastboot flash system 01\blob
sending 'system' (800199 KB)...
OKAY [ 97.595s]
writing 'system'...
OKAY [ 0.067s]
finished. total time: 97.665s
C:\Users\Skythra\Desktop\Android\platform-tools>fastboot devices
???????????? fastboot
After using fastboot and issuing a second command it then stops for a countable 5 seconds before it says ??????????. If i say fastboot -reboot it says success but it doesn't reboot the device. So here's my understanding of what happens:
I load the staging area with the BLOB file
The copy to the staging area completes
fastboot goes crazy and doesn't listen
Next reboot doesn't do the android installation (which people have mentioned but i've never myself seen)
I go back to bootloop
If i reboot the device go back to fastboot, i can send it the command "Fastboot reboot" and it works. But any command after "Flash" nothing else works.
So far there has been a total of zero success I'm about to try the older firmware instead of the same as what's on there.
Okay so,
Apparently because fastboot is there doesn't mean I have real fastboot access. Probably this is my guess:
With JB you get access to Read from fastboot but it doesn't truthfully write. The simplified USB interface might take your data as it's sent but it's probably not storing it.
So the truth of the matter is i'm NOT unlocked. It's exactly as I thought.
I can't recover from trying to move any version of asus official firmware onto the ext_sd card and RCKing (even when the android man appears to work correctly, it still clearly restarts into a bootloop).
So this has to be sent back. Which likely won't be covered by warranty due to the fact that many months ago my now-ex-girlfriend broke the screen.
Fantastic
I can only assume this: Either the OTA update failed and my TF700 then melted itself from the charging+bootloop heat. Else when my ex stood on it, it broke something that would only be used in recovery.
Either way I'm down my 700AUD item and sad for the experience
Ahwell. I suppose i could change the title of this to "Solved" and update the OP as "Unfixable".
Seeing what ASUS was telling people fixing their Prime would cost for user incurred damage, you might be better off just to buy a new tablet. Fixing it would only save a hundred bucks or so and they might void your warranty.
Folks,
I've spent two days trying to sort this out, so you guys are my last hope!!
My Moto G XT1039 (4G) simply will not load a recovery ROM. It has been unlocked successfully but always falls down when I go onto the bootloader screen. When I select recovery (by clicking volume up), it simply says "boot failed".
I've tried all kinds of different recovery files like Clockworks, TWRP etc. and all with the same result.
I've followed all the instructions to the letter re: copying the SuperSU to the SD card. I've also tried copying it to the root of the phone itself.
When flashing the recovery I get the mismatched partition size error, but from what I've read, this is quite common. To combat it I've used the 'erase' function on fastboot and tried again and again. I've even gone back to Android 4.4.4 from 5.1 and still the same result.
I've tried to just load the recovery out of the ram by using the 'load' command, and all I get is a purple screen and then it goes black. This worries me. I'd have thought that should load come what may. The phone works fine once it boots up normally, btw.
I have no important data on here so I'm willing to go to extreme lengths to get this done. Can anybody help me here? I hate popping up in forums and just asking ****, but I've spent a lot of time reading this forum to try and find a solution, and none of them have worked!
Thanks in advance!
Try fastboot boot recovery.img and tell me if it boots the image you're attempting to flash?
Hi there, i would be happy to help you with this , seeing as i have had multiple problems like this with my Moto G3.
Please drop me an fb message @ https://www.facebook.com/profile.php?id=100010666541958 , and we can work together to sort this out. Then post a fix here on the forums.
therealduff1 said:
Hi there, i would be happy to help you with this , seeing as i have had multiple problems like this with my Moto G3.
Please drop me an fb message @ https://www.facebook.com/profile.php?id=100010666541958 , and we can work together to sort this out. Then post a fix here on the forums.
Click to expand...
Click to collapse
Not to undermine your help, but can't you help out by discussing etc. in this thread? That way other users can follow along, help, and solve similar problems themselves also.
Again, I don't mean to belittle your help (it's much appreciated), but if you can help please do so here where others can see.
HTCDreamOn said:
Try fastboot boot recovery.img and tell me if it boots the image you're attempting to flash?
Click to expand...
Click to collapse
Sorry, in my original post I said 'load' when I meant 'boot'. I've already tried this and I just tried it again just to be sure..... all the phone does is it just boots to a purple screen and hangs when I do what you've suggested.
mikeboorman said:
Sorry, in my original post I said 'load' when I meant 'boot'. I've already tried this and I just tried it again just to be sure..... all the phone does is it just boots to a purple screen and hangs when I do what you've suggested.
Click to expand...
Click to collapse
huh that's weird, as all this does is load into ram so I'm not sure why even that won't work.
Can you tell me what your bootloader screen says?
HTCDreamOn said:
huh that's weird, as all this does is load into ram so I'm not sure why even that won't work.
Can you tell me what your bootloader screen says?
Click to expand...
Click to collapse
Thanks for trying to help by the way. It's much appreciated.
The bootlader on the phone adds two lines of yellow commands for a split second before everything goes purple. One of them is something like "CMD download" and the other is a line that has the number 0982800 at the end of it, but it definitely isn't an error message.
Terminal says this:
mikeboormanmbp:~ applemacbook$ cd desktop
mikeboormanmbp:desktop applemacbook$ cd fastboot-mac
mikeboormanmbp:fastboot-mac applemacbook$ cd android
mikeboormanmbp:android applemacbook$ ./fastboot boot recovery.img
downloading 'boot.img'...
OKAY [ 0.323s]
booting...
OKAY [ 0.253s]
finished. total time: 0.577s
Not many clues here I'm afraid!
mikeboorman said:
Thanks for trying to help by the way. It's much appreciated.
The bootlader on the phone adds two lines of yellow commands for a split second before everything goes purple. One of them is something like "CMD download" and the other is a line that has the number 0982800 at the end of it, but it definitely isn't an error message.
Terminal says this:
mikeboormanmbp:~ applemacbook$ cd desktop
mikeboormanmbp:desktop applemacbook$ cd fastboot-mac
mikeboormanmbp:fastboot-mac applemacbook$ cd android
mikeboormanmbp:android applemacbook$ ./fastboot boot recovery.img
downloading 'boot.img'...
OKAY [ 0.323s]
booting...
OKAY [ 0.253s]
finished. total time: 0.577s
Not many clues here I'm afraid!
Click to expand...
Click to collapse
As you can't even use the bootloader properly its probably best to try to flash a stock img being as fastboot is still working for now. Ask here if you need help with this.
EDIT: See post below
Looks like this thread was posted at the wrong place. Xt1039 to my knowledge is not a moto g 2015...it's a moto g 1st gen, right? I have a moto g 1st gen as well (but a different sku) and could only flash recovery images from carrier (get the device from carrier), also couldn't find a way to boot into recovery. I recommend flashing your xt1039 to the latest firmware for your device and then rooting if you want (I was able to root via booting a superboot img file). Doubt you'll be able to sidelead roms. If you're ready to invest in a moto g 2015, would love to further discussing under this section. Cheers.
HTCDreamOn said:
As you can't even use the bootloader properly its probably best to try to flash a stock img being as fastboot is still working for now. Ask here if you need help with this.
Click to expand...
Click to collapse
Yes, I'd be really grateful for some help with it. So I guess I need a link to download the correct stock image, and then a command for fastboot to flash it?
Yesterday I tried to update my phone to android 6.0 but something must have gone wrong during the process because now my phone is stuck in a bootloop, I've tried as hard as i can to fix it but nothing is working. I tried to do a hard factory reset and wiped my phones memory but it won't turn on, I really don't know what to do because I cannot afford to get a new phone.
ineedhelplz said:
Yesterday I tried to update my phone to android 6.0 but something must have gone wrong during the process because now my phone is stuck in a bootloop, I've tried as hard as i can to fix it but nothing is working. I tried to do a hard factory reset and wiped my phones memory but it won't turn on, I really don't know what to do because I cannot afford to get a new phone.
Click to expand...
Click to collapse
If you can get into the bootloader, reflash your firmware to get it back to working condition.
damianx5 said:
If you can get into the bootloader, reflash your firmware to get it back to working condition.
Click to expand...
Click to collapse
Yes I can get into the bootloader but my computer isn't recognizing that my phone is plugged in, it just says charging
ineedhelplz said:
Yes I can get into the bootloader but my computer isn't recognizing that my phone is plugged in, it just says charging
Click to expand...
Click to collapse
Make sure you have all the drivers installed and that you have adb and fastboot files as well.
If you still cant access to transfer files, search for "adb push and pull" commands at google to directly send files to and from your devices.
I am having the same issue!
Here is the difference:
Updated phone to the new OS and my phone went into a boot loop. Booted my phone in Fastboot to try to Factory Reset, it won't reset, it just goes back into Boot Loop... *sobs* I've looked everywhere to find a solution to the following problem, and I'm posting here in order to avoid making unnecessary forums.
My Issue:
As stated above, I updated my phone and it went into boot loop. I am trying to flash it to the previous version, but because I can not factory reset my phone I can not flash my phone. I can not unlock the Bootloader because my USB Debugging is disabled and can not be enabled because my phone is bricked.
I've tried clearing the cache - wipe_data | wipe_cache | fastboot format userdata
I've tried
C:\Users\Name\AppData\Local\Android\android-sdk\platform-tools>fastboot devices
********** fastboot (serial number)
C:\Users\Name\AppData\Local\Android\android-sdk\platform-tools>fastboot flash recovery recovery.img
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
(bootloader) has-slot:recovery: not found
target reported max download size of 268435456 bytes
sending 'recovery' (16484 KB)...
OKAY [ 0.546s]
writing 'recovery'...
OKAY [ 2.699s]
finished. total time: 3.245s
C:\Users\Name\AppData\Local\Android\android-sdk\platform-tools>adb devices
List of devices attached
C:\Users\Name\AppData\Local\Android\android-sdk\platform-tools>
Click to expand...
Click to collapse
Only to later find it did not work due to my Bootloader being Locked...
Here's what I'd like to know: How do I Factory Reset my phone OR Unlock my Bootloader from my computer? Heck, why not tell me both, I can really use the help as this is my only phone and Motorola REFUSED to fix my phone due to some magical liquid damage... to a water resistant phone... that was never once touched by liquid of any kind... but I digress... [...vents on]
About my Phone:
Model XT1548
Rooted: No
Bootlader: Locked
Flashed: No (I believe)
Cause of Problem: Update to Marshmallow
_________________________________________________________
BTW: I made a new thread for this because I wasn't sure if posting here would get any help. HERE
Could you get it working?
I was using the camera on my pixel and it just shut off. It wouldn't turn back on. I had to hold the power button down for almost a minute before it booted back up. Now I'm stuck on the bootloader screen with no way to get into recovery. Clicking on recovery brings me to a failed to load recovery message.
I'm rooted on 7.1.1 December update, unlocked bootloader, stock rom and recovery.
I've tried reading the forum's before posting but im stumped. I've tried flashing the factory image via flash-all bat, but I get stuck at writing 'bootloader'... I've tried flashing twrp with basically the same amount of success, it just saying 'booting' after I run the fastboot boot recovery command. I've tried basically every option in the skipsoft tool kit. Many of the different things I've tried seem to end up getting stuck at the bootloader portion of whatever it is I'm trying to do.
Slot b is the current slot, I feel like that has something to do with it, bl is listed as N/A on the bootloader screen. I successfully ran the fastboot active_slot command to switch to slot a, but when I rebooted slot b is still active. I can't relock the bootloader either, tried that, it says successfully locked, then it reboots and it's still unlocked.
I'm not in front of my PC right now and can give more specific details if anyone has any suggestions.
llong31 said:
I was using the camera on my pixel and it just shut off. It wouldn't turn back on. I had to hold the power button down for almost a minute before it booted back up. Now I'm stuck on the bootloader screen with no way to get into recovery. Clicking on recovery brings me to a failed to load recovery message.
I'm rooted on 7.1.1 December update, unlocked bootloader, stock rom and recovery.
I've tried reading the forum's before posting but im stumped. I've tried flashing the factory image via flash-all bat, but I get stuck at writing 'bootloader'... I've tried flashing twrp with basically the same amount of success, it just saying 'booting' after I run the fastboot boot recovery command. I've tried basically every option in the skipsoft tool kit. Many of the different things I've tried seem to end up getting stuck at the bootloader portion of whatever it is I'm trying to do.
Slot b is the current slot, I feel like that has something to do with it, bl is listed as N/A on the bootloader screen. I successfully ran the fastboot active_slot command to switch to slot a, but when I rebooted slot b is still active. I can't relock the bootloader either, tried that, it says successfully locked, then it reboots and it's still unlocked.
I'm not in front of my PC right now and can give more specific details if anyone has any suggestions.
Click to expand...
Click to collapse
If you can access bootloader, you're still OK. Take a breath, grab a recent adb/fastboot download. The Minimal ADB 1.41 copy isn't the latest but it'll work for this purpose. Redo your flash-all.bat. Be patient. May need to flash boota and bootb if you receive errors about boot slots. Search for CZ Eddie's flash-all instructions if unsure.
llong31 said:
I was using the camera on my pixel and it just shut off. It wouldn't turn back on. I had to hold the power button down for almost a minute before it booted back up. Now I'm stuck on the bootloader screen with no way to get into recovery. Clicking on recovery brings me to a failed to load recovery message.
I'm rooted on 7.1.1 December update, unlocked bootloader, stock rom and recovery.
I've tried reading the forum's before posting but im stumped. I've tried flashing the factory image via flash-all bat, but I get stuck at writing 'bootloader'... I've tried flashing twrp with basically the same amount of success, it just saying 'booting' after I run the fastboot boot recovery command. I've tried basically every option in the skipsoft tool kit. Many of the different things I've tried seem to end up getting stuck at the bootloader portion of whatever it is I'm trying to do.
Slot b is the current slot, I feel like that has something to do with it, bl is listed as N/A on the bootloader screen. I successfully ran the fastboot active_slot command to switch to slot a, but when I rebooted slot b is still active. I can't relock the bootloader either, tried that, it says successfully locked, then it reboots and it's still unlocked.
I'm not in front of my PC right now and can give more specific details if anyone has any suggestions.
Click to expand...
Click to collapse
Download the toolkit and choose option to download and install the latest factory build and when it asks if you want to erase data type n (no) so you will not lose anything. Just make sure you are on the slot that was active which i believe u said was b
quangtran1 said:
If you can access bootloader, you're still OK. Take a breath, grab a recent adb/fastboot download. The Minimal ADB 1.41 copy isn't the latest but it'll work for this purpose. Redo your flash-all.bat. Be patient. May need to flash boota and bootb if you receive errors about boot slots. Search for CZ Eddie's flash-all instructions if unsure.
Click to expand...
Click to collapse
Thanks for the quick response, but the suggestion did not work. I had previsouly tried a version of what CZ Eddie said ( my adb drivers werent updated and I didnt palce the factory image in the same folder as minimal adb). I followed the guide to a T this time with the same result. The below is the same for boot_a and boot_b
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot flash boot_a boot.img
target reported max download size of 536870912 bytes
sending 'boot_a' (24821 KB)...
OKAY [ 0.643s]
writing 'boot_a'...
FAILED (remote: flash write failure)
finished. total time: 1.212s
and this is what I get when trying to run the actual bat file
C:\Program Files (x86)\Minimal ADB and Fastboot>flash-all.bat
target reported max download size of 536870912 bytes
sending 'bootloader_b' (32728 KB)...
OKAY [ 0.876s]
writing 'bootloader_b'...
It just sits there until I cancel the job, I let it run for about 15 min, which is prob 15 min longer than it should take for that particular portion of the batch. My bootloader is ****ed...
llong31 said:
Thanks for the quick response, but the suggestion did not work. I had previsouly tried a version of what CZ Eddie said ( my adb drivers werent updated and I didnt palce the factory image in the same folder as minimal adb). I followed the guide to a T this time with the same result.
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot flash boot_a boot.img
target reported max download size of 536870912 bytes
sending 'boot_a' (24821 KB)...
OKAY [ 0.643s]
writing 'boot_a'...
FAILED (remote: flash write failure)
finished. total time: 1.212s
and this is what I get when trying to run the actual bat file
C:\Program Files (x86)\Minimal ADB and Fastboot>flash-all.bat
target reported max download size of 536870912 bytes
sending 'bootloader_b' (32728 KB)...
OKAY [ 0.876s]
writing 'bootloader_b'...
It just sits there until I cancel the job, I let it run for about 15 min, which is prob 15 min longer than it should take for that particular portion of the batch. My bootloader is ****ed...
Click to expand...
Click to collapse
Well, you're always welcome to send it to me. I'll fix it at no charge one time, plus shipping. I have a team of testers whose only tasks are to break phones, tablets, laptops just so we can put them back together.
llong31 said:
C:\Program Files (x86)\Minimal ADB and Fastboot
Click to expand...
Click to collapse
Get off of minimal and on to Google's fastboot. May not help but there have been a far number of problems with this phone and minimal to not try.
Sounds like when I lost a recovery in one slot doing a sideload in TWRP. I did the temp TWRP load and then added TWRP properly from there. No issues after.
llong31 said:
Thanks for the quick response, but the suggestion did not work. I had previsouly tried a version of what CZ Eddie said ( my adb drivers werent updated and I didnt palce the factory image in the same folder as minimal adb). I followed the guide to a T this time with the same result. The below is the same for boot_a and boot_b
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot flash boot_a boot.img
target reported max download size of 536870912 bytes
sending 'boot_a' (24821 KB)...
OKAY [ 0.643s]
writing 'boot_a'...
FAILED (remote: flash write failure)
finished. total time: 1.212s
and this is what I get when trying to run the actual bat file
C:\Program Files (x86)\Minimal ADB and Fastboot>flash-all.bat
target reported max download size of 536870912 bytes
sending 'bootloader_b' (32728 KB)...
OKAY [ 0.876s]
writing 'bootloader_b'...
It just sits there until I cancel the job, I let it run for about 15 min, which is prob 15 min longer than it should take for that particular portion of the batch. My bootloader is ****ed...
Click to expand...
Click to collapse
I had to do the flash all once because I wiped the whole OS. I just ran it without specifying _a or _b and it worked like a charm. I think where to flash it is in the bat file so it puts it in the right place on its on. I didn't take out the -w to save my data.
TonikJDK said:
Get off of minimal and on to Google's fastboot. May not help but there have been a far number of problems with this phone and minimal to not try.
Click to expand...
Click to collapse
This was going to be my suggestion. It's all I ever use when flashing through fastboot.
Also, as I believe the above poster stated, I don't specify_a or_b when flashing stuff. It usually just works for me.
Hope you get it all working again. If you can access the bootloader, I believe you will be able to.
GeekMcLeod said:
This was going to be my suggestion. It's all I ever use when flashing through fastboot.
Also, as I believe the above poster stated, I don't specify_a or_b when flashing stuff. It usually just works for me.
Hope you get it all working again. If you can access the bootloader, I believe you will be able to.
Click to expand...
Click to collapse
I am not so sure minimal even supports dual partitions. It's latest version is from April. Long before all of this. Might be why people are getting in trouble. It works if you don't specify partition sometimes it seems....We might be on to something here.
quangtran1 said:
Well, you're always welcome to send it to me. I'll fix it at no charge one time, plus shipping. I have a team of testers whose only tasks are to break phones, tablets, laptops just so we can put them back together.
Click to expand...
Click to collapse
Interest to know what you do? Can I have a job
aholeinthewor1d said:
Interest to know what you do? Can I have a job
Click to expand...
Click to collapse
We're a mobile app developer for vertical markets (doctors, lawyers, engineers, warehousing). We put ourselves in customers' position to test our apps. We find ways to break mobile devices, from OS to drivers to incompatibilities to external environment (temperature, sand, rain, etc) in order to error-trap potential issues that users may encounter. We haven't bricked a phone by accident in a long while. If we brick something, we know what we did. That's why I'm speechless that average Pixel users in these forums can brick their phones.
quangtran1 said:
We're a mobile app developer for vertical markets (doctors, lawyers, engineers, warehousing). We put ourselves in customers' position to test our apps. We find ways to break mobile devices, from OS to external environment (temperature, sand, rain, etc) in order to error-trap potential issues that users may encounter. We haven't bricked a phone by accident in a long while. If we brick something, we know what we did. That's why I'm speechless that average Pixel users in these forums can brick their phones.
Click to expand...
Click to collapse
That sounds awesome. Here I am doing tech support from home talking to miserable people all day. But yea it's crazy how quiet it is here. I don't really mean the development side of things either I just mean on general any time I've had new phones at release the forums were filled with people. Hoping after the holidays and as back orders are shipping we get some more people here that can figure this out.
I know I won't have an issue rooting and installing TWRP but I'm a little nervous to flash Roms before this is figured out. Especially because I don't stay on any single ROM that long I like to experiment.
aholeinthewor1d said:
That sounds awesome. Here I am doing tech support from home talking to miserable people all day. But yea it's crazy how quiet it is here. I don't really mean the development side of things either I just mean on general any time I've had new phones at release the forums were filled with people. Hoping after the holidays and as back orders are shipping we get some more people here that can figure this out.
I know I won't have an issue rooting and installing TWRP but I'm a little nervous to flash Roms before this is figured out. Especially because I don't stay on any single ROM that long I like to experiment.
Click to expand...
Click to collapse
Understandable.
quangtran1 said:
We're a mobile app developer for vertical markets (doctors, lawyers, engineers, warehousing). We put ourselves in customers' position to test our apps. We find ways to break mobile devices, from OS to drivers to incompatibilities to external environment (temperature, sand, rain, etc) in order to error-trap potential issues that users may encounter. We haven't bricked a phone by accident in a long while. If we brick something, we know what we did. That's why I'm speechless that average Pixel users in these forums can brick their phones.
Click to expand...
Click to collapse
Im sure you didnt mean it this way, but I didnt do anything to brick the phone, I wasnt flashing twrp or a rom or tinkering in any way. I was just using the camera. The more I'm reading, the more I'm thinking its an issue with 7.1.1 with pixels and nexus 6p's. I RMA'd this, we'll see what happens.
Also, I tried google fastboot, didnt change anything. I let it sit for about an hour and a half running the flash-all.bat, just sits at writing 'bootloader'... One thing I noticed is that with google fastboot is says writing 'bootloader' whereas with minimal adb is gave a specific slot it was writing.
llong31 said:
Im sure you didnt mean it this way, but I didnt do anything to brick the phone, I wasnt flashing twrp or a rom or tinkering in any way. I was just using the camera. The more I'm reading, the more I'm thinking its an issue with 7.1.1 with pixels and nexus 6p's. I RMA'd this, we'll see what happens.
Also, I tried google fastboot, didnt change anything. I let it sit for about an hour and a half running the flash-all.bat, just sits at writing 'bootloader'... One thing I noticed is that with google fastboot is says writing 'bootloader' whereas with minimal adb is gave a specific slot it was writing.
Click to expand...
Click to collapse
There was absolutely no negative connotation in my comment. I stand by my experience that it is improbable to brick a smart phone. I'm just flabbergasted that it happens at all to anyone these days.
llong31 said:
Also, I tried google fastboot, didnt change anything. I let it sit for about an hour and a half running the flash-all.bat, just sits at writing 'bootloader'... One thing I noticed is that with google fastboot is says writing 'bootloader' whereas with minimal adb is gave a specific slot it was writing.
Click to expand...
Click to collapse
Thank you for trying, and letting us know how it went. We are all still gathering info, and it's much appreciated. And glad they rma'd it.
TonikJDK said:
Thank you for trying, and letting us know how it went. We are all still gathering info, and it's much appreciated. And glad they rma'd it.
Click to expand...
Click to collapse
Thought I'd add a little more info...
I cant charge the phone with the phone being turned off. It shows a picture of a battery being charged, screen goes black and flashes a a blue horizontal line across it (kinda like its glitching out). It does this about 3 times and then it automatically turns on without me pushing the power button. Not sure whats causing this, but its strange to say the least.
I made sure I had the latest SDK on my pc, been trying a bunch of different fastboot commands to try and wipe the thing and start over. Every command I run results in- FAILED (remote: failed to erase partition).
I tried searching this error, and its not looking good, most people just RMA'd their devices with many believing the internal sd is corrupted. I hope they accept it back, I checked the tamper flag, and its not on, unlocked is showing as on though (obviously).
llong31 said:
Thought I'd add a little more info...
I cant charge the phone with the phone being turned off. It shows a picture of a battery being charged, screen goes black and flashes a a blue horizontal line across it (kinda like its glitching out). It does this about 3 times and then it automatically turns on without me pushing the power button. Not sure whats causing this, but its strange to say the least.
I made sure I had the latest SDK on my pc, been trying a bunch of different fastboot commands to try and wipe the thing and start over. Every command I run results in- FAILED (remote: failed to erase partition).
I tried searching this error, and its not looking good, most people just RMA'd their devices with many believing the internal sd is corrupted. I hope they accept it back, I checked the tamper flag, and its not on, unlocked is showing as on though (obviously).
Click to expand...
Click to collapse
Sure, a corrupt system would certainly cause the battery replenishment logic to misbehave. It won't know when to fast charge, when to maintain, when to trickle, etc.
llong31 said:
Thought I'd add a little more info...
I cant charge the phone with the phone being turned off. It shows a picture of a battery being charged, screen goes black and flashes a a blue horizontal line across it (kinda like its glitching out). It does this about 3 times and then it automatically turns on without me pushing the power button. Not sure whats causing this, but its strange to say the least.
I made sure I had the latest SDK on my pc, been trying a bunch of different fastboot commands to try and wipe the thing and start over. Every command I run results in- FAILED (remote: failed to erase partition).
I tried searching this error, and its not looking good, most people just RMA'd their devices with many believing the internal sd is corrupted. I hope they accept it back, I checked the tamper flag, and its not on, unlocked is showing as on though (obviously).
Click to expand...
Click to collapse
Did you have an outdated fastboot binary? If you can still get in bootloader, I'd try with the good fastboot from the Android SDK.