Database Info

PX5 Android head unit no sound

I just bought a Belsee PX5 Octo Core Android Head Unit for my 2016 Hyundai Veloster. It has a custom harness made for the car. It works great, except there is no sound. The backup camera works, the steering wheel controls work. Everything works....except sound. I am trying to work with Belsee via Email, but we all know how that goes. I am wondering if any of you fine people might have any suggestions that I can try.
I have gone into Factory Settings menu and changed the CANBUS to Hyundai &KIA, still no sound. The Veloster requires a signal over the CANBUS to turn the factory Amp on and produce sound.
Thanx in advance.

what did the reseller suggest when you contacted them for support? Was that to change CanBus settings?

Hi, i have the same problem after upgrading from px3... Did you resolve the problem?

I now have sound..had to swap to a harness with a CANBUS controller on it. But, the EQ does not work, the rear speakers are super low, and there is that electrical whine from the engine. But at least there is sound.

Hi I am new here but I also had the same issue with my Nissan qashqai and the Bose system. I have found that on my vehicle in the Belsee power harness that pin 1 was not present which is the 12v positive that feeds the Bose sound system. I would suggest you get a wiring diagram for the cars head unit and check to see if this is the problem.

Steering wheel controls not working

Radio Dasaita quad core Oreo 10.2
MTCE_HA_V2.89_1
Car nissan - Xtrail/Rogue
Non canbus verion
The steering wheel controls are not working. I loaded the steering wheel keys app. The app does not show any key as being pressed/detected.
There are 4 plugs on the Dasaita harness. There are two connectors in car plus antenna.
Dasaita harness
Nissan medium low power cable 7022-20-2111
Nissan medium plug
Nissan low plug
other two wire plug
Antenna connector
The Nissan medium plug and the low plug are the same. Medium plug has more wires in it.
I connected only these two plugs from Dasiata harness to the nissan car harness
Nissan medium low power cable
Nissan medium plug
Is this correct?

yogesh201 said:
Radio Dasaita quad core Oreo 10.2
MTCE_HA_V2.89_1
Car nissan - Xtrail/Rogue
Non canbus verion
The steering wheel controls are not working. I loaded the steering wheel keys app. The app does not show any key as being pressed/detected.
There are 4 plugs on the Dasaita harness. There are two connectors in car plus antenna.
Dasaita harness
Nissan medium low power cable 7022-20-2111
Nissan medium plug
Nissan low plug
other two wire plug
Antenna connector
The Nissan medium plug and the low plug are the same. Medium plug has more wires in it.
I connected only these two plugs from Dasiata harness to the nissan car harness
Nissan medium low power cable
Nissan medium plug
Is this correct?
Click to expand...
Click to collapse
What is your HU model number?
Check under Factory settings/canbus for a suitable option for your car; based on some Dasaita units wiring information your car need a decoder named CB008 if you previously had the default 7" screen unit
Usually you need a canbus decoder box to retain SWC controls or maybe you need connect wires named KEY1, KEY2, KEY GND to steering wheel for use controls.

Hi
Thank you for replying. Mr car did not have the 7 inch screen (NAV).
OEM radio info
Maker VISTEON
Supplier code 5AL9
Nissan part code 28185 6fp1A
part name G13-p32
Dasaita radio info
Model PX5 (1024x600)
Kernel 4.4.93+
SW box NOF-RZ-02
SW:V0003
HW:ND02
(180615)
I got the Dasaita radio with the CB011 option.
I have this OEM radio (LHS)
See this picture marked 'without screen'
https://ae01.alicdn.com/kf/HTB1FVLpvY9YBuNjy0Fgq6AxcXXap.jpg
I tried changing the canbus option to number 37(on the radio) but this does not work.
Do you know which of the plugs need to be connected?(see original post)
On a different note. I put the OEM radio back into the car.
It now says "Locked, contact dealer"
What do I do to get this working?

yogesh201 said:
Hi
Thank you for replying. Mr car did not have the 7 inch screen (NAV).
OEM radio info
Maker VISTEON
Supplier code 5AL9
Nissan part code 28185 6fp1A
part name G13-p32
Dasaita radio info
Model PX5 (1024x600)
Kernel 4.4.93+
SW box NOF-RZ-02
SW:V0003
HW:ND02
(180615)
I got the Dasaita radio with the CB011 option.
I have this OEM radio (LHS)
See this picture marked 'without screen'
https://ae01.alicdn.com/kf/HTB1FVLpvY9YBuNjy0Fgq6AxcXXap.jpg
I tried changing the canbus option to number 37(on the radio) but this does not work.
Do you know which of the plugs need to be connected?(see original post)
On a different note. I put the OEM radio back into the car.
It now says "Locked, contact dealer"
What do I do to get this working?
Click to expand...
Click to collapse
Try other nissan Xtrail/QASHQAI/Rogue canbus "voices" in factory setting and check if they working after reboot.
For the "Locked..." i think you need use the radio unlocking code provided to you when buyed the car
Look at this maybe can help: Android Car Multimedia System Nissan Qashqai (installing)

Using the HU to update the instrument panel clock

Hi All,
What is the best way to update the CANBUS clock on my car's instrument panel?
The clock on my instrument panel is apparently controlled by the head unit over the CANBUS. Now that I have an Xtrons PX5 MTCE GS unit head unit, the clock on the dash board just stays at 12:00pm. I drive a Ford Mondeo MK4.
My old PX3 Eonon unit could send radio station data to the instrument panel, but the new Xtrons one sends nothing.
I was thinking of a USB->CANBUS adapter on the head unit and writing an Android script to push the current time to the instrument panel, but wanted to see if anyone's got any better ideas first.
From my limited understanding, the CANBUS adapters supplied with the head units are tied to the MCU's and are solely designed to transfer steering wheel keys - the fact my previous Eonon unit did confuses me..
Many thanks for any input,
Tim

Canbus BOX decoder from other manufacturers, it´s possible? Someone tried.

I have a HU that is from the manufacturer Autonavigo (purchased from Amazon), it does not have a 100% compatible canbus with the buttons of my vehicle and at the time it sold me one that has 75% compatibility but some buttons on the steering wheel and some functions the vehicle does not. By chance, one day, I found a CANBUS BOX decoder on Aliexpress that is 100% compatible with all the functions of my car (confirmed with the seller) and I am tempted to buy it but the seller does not comment on whether it would be compatible with my HU.
I have a high level of electronics and I have observed that the MOLEX connector that this CANBUS decoder has is exactly the same (even the same number of pins). It has the typical CANBUS + and CANBUS- and other power supplies from the CANBUS box. The question I have is if the pins match, I would like to know what pinout these boxes have exactly and the possibility of adapting it to a HU from another manufacturer. What do you think about it? THx

Every PX5 and PX head unit can work with a canbus decoder from different manufacturers. You have to go to Android Settings > Car settings > Factory settings (password: 126) > Canbus tab > Select the manufacturer of your canbus decoder and the car model.
I have a PX5 head unit with a canbus decoder from "Simple", and when it broke, I replaced it with "Raise" and it works.
I recommend to review the list of supported canbus decoders in your head unit in the Factory settings, before purchasing a new one.

Question Xtrons Head unit for 2010 Lexus IS250, cant get some Steering Wheel Controls to work!

Hi everyone
I have a facelift 2010 Lexus IS250 F Sport, I've had some large success installing this XTRONS head unit for it and I am largely satisfied with it. I am however having an issue with getting Steering Wheel Controls to work with the head unit.
Lexus | Various | Android 10 | Octa Core | 4GB RAM & 64GB ROM | Integrated 4G Solution | PMA10ISLS
XTRONS PMA10ISLS is a 10.1" large screen car stereo with customized face panel and optimized CANbus Decoding for Lexus. It supports CarAutoPlay, built-in DSP, PIP mode enabled ,Dual Theme, Instant Rear Vision and so on.
xtrons.co.uk
Lexus| Various | ISO Wiring Harness | MOST
This ISO Wiring Harness is compatible with XTRONS custom fit units PSP10ISL,PMA10ISL etc. If your car is Lexus IS250/IS300/IS350 Convertible (2-door)with original navigation or fibre amplfier system,you need this cable to aid for the installation.
xtrons.co.uk
This is the unit I purchased, alongside a special wiring harness so that I could use it with my vehicle as its a facelift Navi.
With the default CANbus setting on my head unit, only Volume control seems to work and the phone call buttons and voice command buttons are mapped to functions like Radio and Hey Google but I cannot programme these on the app. With an alternative CANbus setting I get skip track functionality but I get different AC Controls and lose access to my factory amp settings.
The original wiring harness I got for the headhunt has not been used at all as I was instructed to usr the special harness, and that original harness had a CANBUS decoder. XTRONS claim that I am unable to programme the SWC due to the CANBUS needing to decode it, although I have played around with the settings and selected various different CANBUS settings.
Would anyone be able to advise me on how I can get the SWC working, would it involve plugging the CANbus decoder into the head unit? There is a 12 pin connection spare at the back but I am unsure if that would make the difference or not.