Database Info

Boot Animation with SkyRaider

Sorry about the post but I cannot find the post were it tells me how to install custom boot animations. I also need to be able to do the sounds. As far as I understand I have to put it in the media folder. I found the original one but it does not allow me to move it. I'm assuming I have to do it from recovery but I don't know how. Detailed instructions would be appreciated. I have a cold and the old brain is doing so well. Thanks

s-off your dinc and you can do it while booted

I was trying to avoid that because they do not have a way to undo s-off yet. Just incase my phone dies I dont want verizon to say I voided the warranty. Any way to do it without?

You can flash some of them from rom manager...that's how I did mine.

If you have rooted your phone, which you must have in order to install a custom ROM, you've already voided your warranty.
Adding S-OFF wouldn't change anything in the eyes of Verizon, and you can always drop your phone until it's physically broken if you need to take it in.

rom manager -> download rom -> Ihtfp69 -> boot animations -> download -> pick one
thats where i got mine from

MMBosstones86 said:
rom manager -> download rom -> Ihtfp69 -> boot animations -> download -> pick one
thats where i got mine from
Click to expand...
Click to collapse
When I try to install from Rom manager it doesn't load it says verification failed or something. Does anyone know how to manually install Droid 2 boot screen.
HTC incredible
SR sense 2. 5. 2
Radio 2. 15
Sent from my ADR6300 using XDA App

Did mine 'manually', since I'm rooted I have clockwork mod installed.
1. Boot into recovery (clockwork mod)
2. launched android SDK adb daemon
3. moved file from 'tools' folder of sdk to the proper destination on the phone.
4. Done.

Doctor Butts said:
Did mine 'manually', since I'm rooted I have clockwork mod installed.
1. Boot into recovery (clockwork mod)
2. launched android SDK adb daemon
3. moved file from 'tools' folder of sdk to the proper destination on the phone.
4. Done.
Click to expand...
Click to collapse
I'm not sure how to do step 2 your referring to. If you have a link to a thread that explains how to do that, it would be greatly appreciated.
Sent from my ADR6300 using XDA App

Well, you have to go to the android website and download the android SDK. Install it somewhere on your computer that's easy to access, preferably put the folder at the root of one of your hard drives.
You'll go into command prompt after that to do a lot of the work to transfer files.
So, make sure USB debugging is enabled (just in case) and boot your phone into cwm recovery. Connect the phone to your computer via USB.
in command prompt, cd to the android sdk's tools directory. From there, you can use the adb commands to transfer files.
So, for me, after connecting the phone I do the following in command prompt:
cd G:
cd androidsdk/tools
and then I use ADB to communicate with phone, first by verifying the phone is connected:
adb devices
(if adb is on your pc, it will auto run the daemon if it is not running)
If your phone shows up in recovery mode, you're set.
You may need to go into cwm and mount your system/sd card before transferring the file.
From there, you use adb shell to acess the phone's file systems.
If you put the boot animation to the phone you'll do something like (while in shell) mv bootanimation.zip system/somethingorother/bootanimation.zip
But don't take the above line as gospel. I dont remember the exact command line to use. Check the thread on "How 2 - ADB, Rooting...." for a list of commands in ADB shell and search for a webpage that gives basic linux commands.

Doctor Butts said:
Well, you have to go to the android website and download the android SDK. Install it somewhere on your computer that's easy to access, preferably put the folder at the root of one of your hard drives.
You'll go into command prompt after that to do a lot of the work to transfer files.
So, make sure USB debugging is enabled (just in case) and boot your phone into cwm recovery. Connect the phone to your computer via USB.
in command prompt, cd to the android sdk's tools directory. From there, you can use the adb commands to transfer files.
So, for me, after connecting the phone I do the following in command prompt:
cd G:
cd androidsdk/tools
and then I use ADB to communicate with phone, first by verifying the phone is connected:
adb devices
(if adb is on your pc, it will auto run the daemon if it is not running)
If your phone shows up in recovery mode, you're set.
You may need to go into cwm and mount your system/sd card before transferring the file.
From there, you use adb shell to acess the phone's file systems.
If you put the boot animation to the phone you'll do something like (while in shell) mv bootanimation.zip system/somethingorother/bootanimation.zip
But don't take the above line as gospel. I dont remember the exact command line to use. Check the thread on "How 2 - ADB, Rooting...." for a list of commands in ADB shell and search for a webpage that gives basic linux commands.
Click to expand...
Click to collapse
THANK YOU SIR. MUCH APPRECIATED.
Sent from my ADR6300 using XDA App

[APP]MTK ADB, Use ADB directly on your device

MTK ADB gets you a privileged shell at the push of a button, allowing you to run commands directly on your MediaTek device. Some might wonder if rooting hasn't already solved this. Firstly, root access is persisted by modifying system files. When the real binary gets substituted by that of the root app's, if the device is rebooted, the init daemon running as root runs the binary giving the app root. What's wrong with this? If you have “purist” tendencies, you probably would want your phone as stock as possible, or at least with your permission. Sadly, not only binaries are dumped. Extra temp files, logs and helper binaries too, that manually removing them is like dancing on floor of pins and a prick means a brick. Not only that, consider yourself blocked from updates. If you're unfortunate enough, an update could result in bricking your phone as the files supposed to be present had been changed. This is more common than you think. MTK ADB makes no changes to your files whatsoever. Also, there's the matter of security/privacy. Root apps tend to always do something in the background. Either sneaking in a new app, or phoning home with your private data, or both. MTK ADB doesn't steal your data. The Internet permission is for Telnet, etc. On some devices, MTK ADB can get root access (depending on manufacturer) while all devices can get shell access. You just have to check which yours belongs.
IMPORTANT
•Refresh before (and after) clicking Start to check ADB status.
•Supports all ADB functionality. Just run "adb <command>" eg "adb pull" (without quotes).
•The minimalist terminal is for those who haven't any. Feel free to use your regular terminal (I use Terminal IDE) and keyboard (Hacker's Keyboard is really good). Just run "adb shell" on it.
•You can connect to your device using another phone, PC, or anything with a terminal and in the same network by running "adb connect IP_address".
•If you get a " device offline" error, disable and enable USB debugging. Next time connect to the network before running the app.
http://www.youtube.com/watch?v=_bt8BVaDCf0
http://slaycode.WordPress.com

Bump

Proof:
http://forum.xda-developers.com/gen...iled-error-t3191150/post62611445#post62611445
More Proof:
http://forum.xda-developers.com/fire-phone/general/root-fire-phone-supersu-t3105546/page10

Proof:
http://forum.xda-developers.com/gen...iled-error-t3191150/post62611445#post62611445
More Proof:
http://forum.xda-developers.com/fire-phone/general/root-fire-phone-supersu-t3105546/page10

When I open the app it opens but it doesn't work when I enter the commands and moreover the app when I try to start the adb it says unsupported device
Am using infinix hot 4 pro running NOUGAT xos 2.2

LordFME said:
MTK ADB gets you a privileged shell at the push of a button, allowing you to run commands directly on your MediaTek device. Some might wonder if rooting hasn't already solved this. Firstly, root access is persisted by modifying system files. When the real binary gets substituted by that of the root app's, if the device is rebooted, the init daemon running as root runs the binary giving the app root. What's wrong with this? If you have “purist” tendencies, you probably would want your phone as stock as possible, or at least with your permission. Sadly, not only binaries are dumped. Extra temp files, logs and helper binaries too, that manually removing them is like dancing on floor of pins and a prick means a brick. Not only that, consider yourself blocked from updates. If you're unfortunate enough, an update could result in bricking your phone as the files supposed to be present had been changed. This is more common than you think. MTK ADB makes no changes to your files whatsoever. Also, there's the matter of security/privacy. Root apps tend to always do something in the background. Either sneaking in a new app, or phoning home with your private data, or both. MTK ADB doesn't steal your data. The Internet permission is for Telnet, etc. On some devices, MTK ADB can get root access (depending on manufacturer) while all devices can get shell access. You just have to check which yours belongs.
IMPORTANT
•Refresh before (and after) clicking Start to check ADB status.
•Supports all ADB functionality. Just run "adb <command>" eg "adb pull" (without quotes).
•The minimalist terminal is for those who haven't any. Feel free to use your regular terminal (I use Terminal IDE) and keyboard (Hacker's Keyboard is really good). Just run "adb shell" on it.
•You can connect to your device using another phone, PC, or anything with a terminal and in the same network by running "adb connect IP_address".
•If you get a " device offline" error, disable and enable USB debugging. Next time connect to the network before running the app.
http://slaycode.WordPress.com
Click to expand...
Click to collapse
Are you familiar with an APK that utilizes mtk_bypass to directly flash firmware to device.
I'm looking for an APK that basically does what sp flash tool does because I don't have a computer.

How to Install adb/fastboot on Android device (phone) to use to fix another phone

A friend of mine has a Stylo 6 that says corrupted when it boots. It is however already set to USB debugging. However, I do not have access where I'm at to a PC or a Chromebook to install the dev tools. Is it possible even with third party paid software to install the dev environment on another Android phone and use it for fastboot etc?

You don't need to add ADB and/or Fastboot to any Android device. In common both ADB and Fastboot ( the latter only unless OEM decided to omit it ) are integral part of every Android release: ADB is housed in Android's user-space, Fastboot typically is part of device's bootloader unless Android has a Dynamic Partition layout, then Fastboot is also housed in Android's user space.

Ok, I guess what I need to know if I can install and use adb server on an Android device. I don't have access to a PC Mac or Chromebook to install the sdk tools. Can this be installed on my phone ( using a Linux or windows emulator maybe) to use to fix his phone?

ADB is nothing more than a tool that allows you to execute commands which would interact with Android shell. So you can install / open in Android a shell app ( e.g. Termux ) and run the commands ( Linux compliant ) therein. Will say you don't need a computer to operate on Android system of device,

Op7pro not responding to fastboot commands

Hey, im having trouble finding working ways to root my op7pro GM1913 (OOS 11.0.4.1 GM21BA)
Ive been trying this https://www.xda-developers.com/unlock-bootloader-root-oneplus-7-pro/
Currently trying to unlock bootloader. (Step 2)
I can connect via adb but when i go to bootloader/fastboot i lose connection to the phone.
Ive tried regular adb command tools and "TOOL ALL IN ONE" When the phone is on it responds to adb commands but when i need fastboot commands its not working and i can see the device id dissapear from the all in one tool.
I have tried multiple usb ports (2.0 and 3.0) and multiple usb C cords (Op oem + Samsung) Tried removing Windows signature verification and installing oneplus usb drivers, but it gets stuck at "Execute the commands..." (99% or so) When i try again it finds some installation files. When im in bootloader, Windows device manager still shows a generic android phone. Oem unlocking and usb debugging is on, also set default usb configuration to file transfer. No help.
I want to keep Oxygen os, but i want to be rooted and have magisk, preferably TWRP too but im open to other ways.
Windows 10 20H2 if that matters. (Latest update for me)
Oneplus 7pro GM1913 (Eu nordic)
Oxygen os 11.0.4.1 GM21BA

Download a Linux distro and install adb and fastboot like this: https://forum.xda-developers.com/t/guide-unlock-flash-root-for-the-pixel-2-xl-taimen.3702418/
Just download adb and fastboot tools package from Google, extract it,open command prompt inside where you extract it and enter these in terminal:
sudo install adb dmtracedump e2fsdroid etc1tool fastboot hprof-conv make_f2fs mke2fs mke2fs.conf sload_f2fs sqlite3 /usr/local/bin
sudo mkdir -p /usr/local/lib64
sudo install lib64/libc++.so /usr/local/lib64
Then adb --version (enter) fastboot --version (enter) like Nathan says in guide. Super easy and I guarantee you if you go this route you won't have any hiccups. Sounds like stupid windblows driver issues or outdated adb/fastboot tools. One of the two. Are you flipping on dev options and check marking little box that pops up on your phone to allow it to communicate with PC? A simple : adb devices (enter) should make it appear on phone screen. You don't even have to install Linux, you can boot it off a live USB. Takes about one minute to make one. If you make one you can boot the live USB , download adb and fastboot, and install as Nathan's guide says then reboot when you are done and your back in windblows. IDK why anyone wouldn't want Linux installed though. Best decision I ever made was switching from windows to Linux about 9 years ago. It really makes anything you do to your devices MUCH easier to do!! This may sound stupid but have you rebooted your PC? Because you will definitely need to , probably more than once on windblows to get it to work.

Thank you for the reply. No stupid questions, yes i tried rebooting pc/phone. Ill try your way and report in a couple days.

Solution is simple. From Android 11 on, OnePlus (and Android phones in general) uses the universal drivers, you just need to install them in Windows in order to use fastboot commands. See my answer in this post.

There are a few things you can try if your OP7 Pro is not responding to fastboot commands:
1. Make sure you have the latest drivers installed for your phone.
2. Try using a different USB cable.
3. If you're using Windows, try running the fastboot commands from a command prompt with administrator privileges.
4. Try booting your phone into recovery mode and running the fastboot commands.

[APP][NON-ROOT] Termux-ADB - debug one Android device from another connected by USB-OTG

Run adb in Termux without root permissions!​This is a launcher for adb which enables debugging of one Android device from another via USB cable. It should work with any USB-C male-to-male cable or the corresponding OTG adapter + cable in case of micro USB.
https://github.com/nohajc/termux-adb
Motivation​Termux has had the android-tools package for some time now but it only works properly if you root your device (due to missing filesystem permissions). This is because Android has its own API for accessing USB peripherals which is incompatible with Linux. Termux already exposes this API using the termux-usb utility (part of Termux API) but this is not enough to make programs like adb work out of the box.
Usually you would have to modify any application which accesses USB devices but there's actually another way.
When you start adb using termux-adb, it will use termux-usb in the background for device discovery and then essentially feed the device information into adb by intercepting some libc calls and emulating usb device files as they would appear on any linux machine (bypassing the file permission problem entirely).
At this point the program is in its early stages and therefore highly experimental. I tested it on two Android devices so far and I can't give any guarantees it will work for everyone. But you can try.

That is great work！ It works fine in my honor handset!
When will you share the new release with multiple ADB device support?
Appreciate for your fantastic tool !

It's definitely on my TODO list but now I'm also dealing with the fact it doesn't work on some devices.
So, I don't have an exact timeline but I'll keep this thread up to date.

Version 0.2 released today: https://github.com/nohajc/termux-adb/releases/tag/v0.2.0
@Stanton1011 It supports multiple devices now.

Thank you. If you're wanting feedback, there seems to be a lot of lag getting it to connect at first but it does work and once it's connected no issues. The fastboot however has much more lagging and will say simultaneously that commands succeeded and failed (but just seem to fail). But adb works fine on moto g pure running android 11, moto g pure on Android 12, TCL Obama phone type android 12, Samsung a11 android 10.

Thanks for the report. I'm aware of the lag. It's mainly caused by how Termux handles USB access in general but it could be improved if fastboot ran in the background (same as adb).
As for the commands failing, I'll look into it. Which particular fastboot commands you tried?

nohajc said:
Version 0.2 released today: https://github.com/nohajc/termux-adb/releases/tag/v0.2.0
@Stanton1011 It supports multiple devices now.
Click to expand...
Click to collapse
Thank you so much, I will have a try and let you know the result.

The following problem is solved by Pkg upgrade.
I find a error for it ,please help!
CANNOT LINK EXECUTABLE "./termux-adb": cannot locate symbol "_ZN6google8protobuf8internal14ArenaStringPtr3SetIJEEEvRKNSt6__ndk112basic_stringIcNS4_11char_traitsIcEENS4_9allocatorIcEEEEPNS0_5ArenaE" referenced by "/data/data/com.termux/files/home/termux-adb"...

I have a handset with the root permission only for ADB, but Termux(or any android APP) can not obtain the root permission. Could you tell a way to use the adb in termux, I know I can user your github project Termux-adb as what you did before., but I also need a alternative way. I have the root permission of ADB command（by PC）. Can I modify some folder permission to achieve the same affect?