Question New P11 stuck on Fast Boot after update - Lenovo P11

Hi,
I used Rescue and Smart Assistant to install the latest firmware on my new P11, which finished successfully, however,now it is stuck at fast boot and when I choose to enter Recovery Mode it starts again in Fast Boot.
I tried also flashing using qfil, it also finished successfully, but still stucked in fast boot.

I managed to make it working after updating it using Smart Assistant, I guest that I entered the two-digit hardware code wrong.

Hi! I am having this kind of problem too for the past week after i bought it tried to update it. Can you elaborate how you manage to fix it because even if i use QFIL, it's not letting me to flash the hardware. Hoping for your response and thank you!

You can try this:
1. Don't connect your tablet with PC.
2. Press Power button + Volumn (+) + Volumn (-) for seconds for get out flashboot mode.
3. Flash ROM version 210520 with Qfil.
This is work for my P11 CN version.

Me too. Please help

mklevi said:
You can try this:
1. Don't connect your tablet with PC.
2. Press Power button + Volumn (+) + Volumn (-) for seconds for get out flashboot mode.
3. Flash ROM version 210520 with Qfil.
This is work for my P11 CN version.
Click to expand...
Click to collapse
can you elaborate what settings on qfil , i have lenovo p11 4/64gb version

famicom9x said:
can you elaborate what settings on qfil , i have lenovo p11 4/64gb version
Click to expand...
Click to collapse
A. Qfil-Configuration-FireHoseConfiguration:
1. device type: ufs
2. Reset After Download: check
turn it off, disconnect to PC, open Qfil, press down the "volume +" buttom (do not release) and connect to pc (release till Qfil shows "Qualcomm HS-USB QDLoader 9008(comx)").
B. the main window:
load content: the contents.xml file
build type: meta
then press download content and wait till it boots.

asukav said:
A. Qfil-Configuration-FireHoseConfiguration:
1. device type: ufs
2. Reset After Download: check
turn it off, disconnect to PC, open Qfil, press down the "volume +" buttom (do not release) and connect to pc (release till Qfil shows "Qualcomm HS-USB QDLoader 9008(comx)").
B. the main window:
load content: the contents.xml file
build type: meta
then press download content and wait till it boots.
Click to expand...
Click to collapse
thank, there are a setting calledd "
Availible Meta Build Storage Types"
what must i choose? emmc or ufs?

Download with the Smart Assistant Tool from Lenovo latest firmware version TB_J606F_S320029_210923_ROW.
First Start Qfil.
The Qfil file is where the new firmware by Rescue and Smart Assistant is stored.
For me it was in the folder c:/ProgramData/RSA/Download/RomFiles/ToolFiles/Qfil
1: The tablet must not be connected to the computer and must be off.
2: Now start Qfil, at the top of the screen is now "No Port Available" start now the tablet by holding down the Volume + button and at the same time connecting the USB cable to the computer or laptop, You will feel a slight vibration in the tablet.
3: Now you see in the screen that a port is present, so you are now in contact with the Qfil programmer.
4: In the Qfil screen you will see "Select Build Type" choose "Flat Build"
5: At "Select Programmer" press "Browse" choose there prog_firehose_ddr.elf
6: Now press "Load XML" and choose rawprogram_unsparse0 and patch0
7: Now press "Download" the installation will now start so wait until it is finished.
8: After the installation is finished, disconnect the USB connection and restart the tablet:
9: The tablet may start up with the FFBM mode screen, then turn the tablet off again by holding the power button for longer seconds.
10: Start the tablet by pressing the volume - button and the power button.
11: In the screen choose with the volume buttons "Recovery" then in de next screen "Reboot system", the tablet will now start up normally again, this will take a while so wait patiently.
12: Then you come to the welcome screen, this was it and the tablet should now work properly again with the new Android 11 version, good luck!

comtech2005 said:
Download with the Smart Assistant Tool from Lenovo latest firmware version TB_J606F_S320029_210923_ROW.
First Start Qfil.
The Qfil file is where the new firmware by Rescue and Smart Assistant is stored.
For me it was in the folder c:/ProgramData/RSA/Download/RomFiles/ToolFiles/Qfil
1: The tablet must not be connected to the computer and must be off.
2: Now start Qfil, at the top of the screen is now "No Port Available" start now the tablet by holding down the Volume + button and at the same time connecting the USB cable to the computer or laptop, You will feel a slight vibration in the tablet.
3: Now you see in the screen that a port is present, so you are now in contact with the Qfil programmer.
4: In the Qfil screen you will see "Select Build Type" choose "Flat Build"
5: At "Select Programmer" press "Browse" choose there prog_firehose_ddr.elf
6: Now press "Load XML" and choose rawprogram_unsparse0 and patch0
7: Now press "Download" the installation will now start so wait until it is finished.
8: After the installation is finished, disconnect the USB connection and restart the tablet:
9: The tablet may start up with the FFBM mode screen, then turn the tablet off again by holding the power button for longer seconds.
10: Start the tablet by pressing the volume - button and the power button.
11: In the screen choose with the volume buttons "Recovery" then in de next screen "Reboot system", the tablet will now start up normally again, this will take a while so wait patiently.
12: Then you come to the welcome screen, this was it and the tablet should now work properly again with the new Android 11 version, good luck!
Click to expand...
Click to collapse
Hi. I saw your post on Forum Lenovo. I followed your instructions but it failed (ver 210923). Can you make a video tutorial? I want to see where I went wrong.
Thank you!

hungali33 said:
Hi. I saw your post on Forum Lenovo. I followed your instructions but it failed (ver 210923). Can you make a video tutorial? I want to see where I went wrong.
Thank you!
Click to expand...
Click to collapse
Install the QPST file and then go to the bin folder. It contains the QFIL.exe there. Then follow the instructions by comtech2005. Do not install the later version TB-J606F_S320109_211207_ROW.zip. I got stucked in the start/ffbm etc mode. What I did was use QFIL in the QPST folder and then revert to the 210923 ROW. It went smoothly using this qfil version.
As additional info surprise, it prompted me for the 211207 ROW OTA update. Hope this works ok after installing the OTA update.

MSJI said:
Install the QPST file and then go to the bin folder. It contains the QFIL.exe there. Then follow the instructions by comtech2005. Do not install the later version TB-J606F_S320109_211207_ROW.zip. I got stucked in the start/ffbm etc mode. What I did was use QFIL in the QPST folder and then revert to the 210923 ROW. It went smoothly using this qfil version.
As additional info surprise, it prompted me for the 211207 ROW OTA update. Hope this works ok after installing the OTA update.
Click to expand...
Click to collapse
Yup, installing the OTA update takes about 10 minutes and am now on 211207 ROW version.

I have a new China-sourced P11 Pro (TB-J706F) that is now stuck on the bootloader screen. I've tried the Lenovo Rescue and Smart Assistant to install the latest ROM and it fails partway through the fix process. I've also tried the standalone QFIL process with several ROMs for this device - these also quit part way through. Is the device fixable?

GideonS said:
I have a new China-sourced P11 Pro (TB-J706F) that is now stuck on the bootloader screen. I've tried the Lenovo Rescue and Smart Assistant to install the latest ROM and it fails partway through the fix process. I've also tried the standalone QFIL process with several ROMs for this device - these also quit part way through. Is the device fixable?
Click to expand...
Click to collapse
As I have advised, this failed on me too when I used LMSA or the standalone QFIL download. Use the QPST download where it has the QFIL.EXE and then follow instructions in the previous postings.

MSJI said:
As I have advised, this failed on me too when I used LMSA or the standalone QFIL download. Use the QPST download where it has the QFIL.EXE and then follow instructions in the previous postings.
Click to expand...
Click to collapse
Still no luck. Tried on 2 different PCs and with 2 different cables.

GideonS said:
Still no luck. Tried on 2 different PCs and with 2 different cables.
Click to expand...
Click to collapse
What rom version you are installing and what was the previous rom when it was working ok?

MSJI said:
What rom version you are installing and what was the previous rom when it was working ok?
Click to expand...
Click to collapse
I'm embarrased to say I didn't check the ROM version before trying to upgrade to latest ROW. But it's reporting as S620022_210910_ROW in the Android Recovery menu
But I've tried to upgrade to several versions inc..
TB-J706F_S620108_211124_ROW
TB-J706F_S250260_210804_ROW
TB-J706F_S241015_210326_ROW
TB-J706F_CN_WIFI_USER_Q00018.0_Q_ZUI_12.0.335_ST_201103_qpst
Thanks again for your ongoing advice

GideonS said:
I'm embarrased to say I didn't check the ROM version before trying to upgrade to latest ROW. But it's reporting as S620022_210910_ROW in the Android Recovery menu
But I've tried to upgrade to several versions inc..
TB-J706F_S620108_211124_ROW
TB-J706F_S250260_210804_ROW
TB-J706F_S241015_210326_ROW
TB-J706F_CN_WIFI_USER_Q00018.0_Q_ZUI_12.0.335_ST_201103_qpst
Thanks again for your ongoing advice
Click to expand...
Click to collapse
When I encountered an issue in my upgrade, I reverted to the last working ROM using the QFIL.EXE in QPST. It went ok. I have no need to use QFIL since my tablet with the working ROM prompted me for an OTA update. So my understanding is that you upgraded your tablet but you do not know what version you upgraded from. So it could be possible that you downgraded from a newer version?

OMG. Just had a breakthrough. I'd been trying firmware flash with 2 different top-quality USB cables, one of which was the supplied Lenovo cable. But after advice here I bought a dedicated EDL cable. I've just tried it and the Flash took!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

GideonS said:
OMG. Just had a breakthrough. I'd been trying firmware flash with 2 different top-quality USB cables, one of which was the supplied Lenovo cable. But after advice here I bought a dedicated EDL cable. I've just tried it and the Flash took!
View attachment 5510781
Click to expand...
Click to collapse
That's great!!

Related

[Guide] How to Root Original Cube T8 and Resize partition

Before we begin, this a guide written by a noob for noobs
Disclaimer; I'm not responsible if you fry your device. Just follow this guide assiduously and you should be fine
Click to expand...
Click to collapse
What you will need;
1. A Cube T8 Phablet with an SD Card
2. A Windows PC (version 7, 8, 8.1, 10 should do)
3. Common Sense
PROCEDURE:
1. Download SuperSU from the Chainfire site and transfer to the root of the SD Card WITHOUT extraction
2. Download and Install MediaTek VCOM drivers . This Youtube Video will help you guide you through the driver installation process.
NB: Depending on your version of Windows, you may need to disable driver signature check. This guide did just that for me on my Windows 10
3. After successfully installing the driver, download the latest version of SPL Flashtool and extract that folder to somewhere like \Desktop
4. Download TWRP Recovery T8 and extract to your \Desktop as well
5. Run flash_tool (which you downloaded in Step 3). If it doesn't run, try and copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1524.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1524.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /TWRP Recovery folder on the desktop (downloaded in Step 4), press "Download" button.
NB: if you did everything correctly you should see that recovery pane in the dialogue box has been checked
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get a "Successful" dialog box
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER buttons simultaneously.
9. Using VOLUME_UP button, select "Recovery" and confirm it by pressing VOLUME_DOWN button. Wait until TWRP Recovery starts.
10. In TWRP Recovery, select "Install ZIP" and point to "/external sd/UPDATE-SuperSU-v2.46.zip" (which we downloaded and placed on the root of the SD Card in Step 1)
11. After installation is finished, select "Reboot". Recovery will reboot the device.
12. After the device has rebooted successfully, you should see a new app named SuperSU in the application drawer.
Boom you have successfully rooted your device if you see the app! If you didn't see this app, you did something wrong and need to repeat the process
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
RESIZING OF THE PARTITION
This was the main reason why I wanted to root the T8 so badly as I was limited to only 2.9GB of internal storage.
1. Download Resize_v22.4.1-signed.zip and copy to the root of SD (without extracting)
2. Turn the device off and run Recovery by pressing VOLUME_UP and POWER button simultaneously.
3. Using VOLUME_UP button, select "Recovery" and confirm it by pressing "VOLUME_DOWN" button. Wait until TWRP Recovery starts.
4. In TWRP Recovery, select 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip"
5. In one of following windows that pop up, select the partition size you desire. I went with 9GB and lost only the apps that I had moved manually to the SD Card.
Here's proof of my new 9GB internal storage after resizing:
Have fun!
Really interesting Thank you for this Information!
Krystyna said:
Really interesting Thank you for this Information!
Click to expand...
Click to collapse
You are welcome!
Can you tell if this would work on New Cube T8 Plus Ultimate?
Thanks un advance
Enviado desde mi bq Elcano mediante Tapatalk
Please anyone knows if this would work on T8 plus?
Enviado desde mi bq Elcano mediante Tapatalk
Hello , I follow all the steps and when i am to step 6 and press download , nothing is downloading , i put tablet to usb and message me installation wrong.
bolija said:
Please anyone knows if this would work on T8 plus?
Enviado desde mi bq Elcano mediante Tapatalk
Click to expand...
Click to collapse
Use this tutorial for the T8 Plus;
http://forum.xda-developers.com/android/general/guide-how-to-root-cube-t8-plus-t3256490
jimfizz said:
Hello , I follow all the steps and when i am to step 6 and press download , nothing is downloading , i put tablet to usb and message me installation wrong.
Click to expand...
Click to collapse
it doesn't really download anything per se. It just downloads to the tablet after you turn it off and connect to the PC
Still something wrong
garzie2000 said:
it doesn't really download anything per se. It just downloads to the tablet after you turn it off and connect to the PC
Click to expand...
Click to collapse
Thank you for your response but still something wrond and i can not complete root.
In step 6 In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" mine scatter loading had MT6735M. I press downloading and continue step 7.
Flashtool start work and get a message box " PMT changed for the ROM; it must be downloaded. I press OK and nothing happened
In step 8 - 9 After choose recovery i went to a menu and there is not any choice install zip. I press reboot and back again here. What i make wrong my friend?
Regards,Dimitris
jimfizz said:
Thank you for your response but still something wrond and i can not complete root.
In step 6 In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" mine scatter loading had MT6735M. I press downloading and continue step 7.
Flashtool start work and get a message box " PMT changed for the ROM; it must be downloaded. I press OK and nothing happened
In step 8 - 9 After choose recovery i went to a menu and there is not any choice install zip. I press reboot and back again here. What i make wrong my friend?
Regards,Dimitris
Click to expand...
Click to collapse
That's weird please make sure that you download the files from this thread and not google and that you have the Original Cube T8 running the latest firmware V 1.2
cube t8s
Hello my friend
I am 100% sure i have download all the files from here , my tablet is the cube t8s , 8g , quadcore , 1gb ram. I have win7 to my pc.
I follow all your steps but still nothing.
Hello garzie2000.
I have the Cube T8. I followed your guide and all went well. Rooted and partition expanded!
Thank you!
---------- Post added at 06:29 PM ---------- Previous post was at 05:57 PM ----------
By the way garzie2000, I tried to install Xposed framework (xposed-v79-sdk22-arm64.zip + XposedInstaller_3.0_alpha4.apk) but I got a bootloop and I'm now restoring my backup.
Did you installed Xposed...?
Thanks!
diboodib said:
Hello garzie2000.
I have the Cube T8. I followed your guide and all went well. Rooted and partition expanded!
Thank you!
---------- Post added at 06:29 PM ---------- Previous post was at 05:57 PM ----------
By the way garzie2000, I tried to install Xposed framework (xposed-v79-sdk22-arm64.zip + XposedInstaller_3.0_alpha4.apk) but I got a bootloop and I'm now restoring my backup.
Did you installed Xposed...?
Thanks!
Click to expand...
Click to collapse
I'm yet to try out the Xposed framework. Still quite experimental so these things are expected
jimfizz said:
Hello my friend
I am 100% sure i have download all the files from here , my tablet is the cube t8s , 8g , quadcore , 1gb ram. I have win7 to my pc.
I follow all your steps but still nothing.
Click to expand...
Click to collapse
Sorry mate. This is for the Original 16GB version of of Cube T8
hi.
if i root T8+ successfully and i want resize partition same this.
I can used "Resize_v22.4.1-signed.zip" file from this post resize partition on T8+ yes or not?
Pregressive said:
hi.
if i root T8+ successfully and i want resize partition same this.
I can used "Resize_v22.4.1-signed.zip" file from this post resize partition on T8+ yes or not?
Click to expand...
Click to collapse
It should work.
Thanks for your post. I followed yours instruction and got it sucessfully.
garzie2000 said:
Before we begin, this a guide written by a noob for noobs
What you will need;
1. A Cube T8 Phablet with an SD Card
2. A Windows PC (version 7, 8, 8.1, 10 should do)
3. Common Sense
PROCEDURE:
1. Download SuperSU from the Chainfire site and transfer to the root of the SD Card WITHOUT extraction
2. Download and Install MediaTek VCOM drivers . This Youtube Video will help you guide you through the driver installation process.
NB: Depending on your version of Windows, you may need to disable driver signature check. This guide did just that for me on my Windows 10
3. After successfully installing the driver, download the latest version of SPL Flashtool and extract that folder to somewhere like \Desktop
4. Download TWRP Recovery T8 and extract to your \Desktop as well
5. Run flash_tool (which you downloaded in Step 3). If it doesn't run, try and copy it to the root folder of your hard drive, eg. C:\SP_Flash_Tool_exe_Windows_v5.1524.00\, albo D:\SP_Flash_Tool_exe_Windows_v5.1524.00\
6. In "Download" section choose "Scatter-Loading" point to "MT6753_Android_scatter" from /TWRP Recovery folder on the desktop (downloaded in Step 4), press "Download" button.
NB: if you did everything correctly you should see that recovery pane in the dialogue box has been checked
7. Turn off the tablet. Connect it via USB to PC (tablet needs to be switched off!). After short while, flashing tool should recognize the tablet and start flashing automatically, installing TWRP recovery. After that you should get a "Successful" dialog box
8. Disconnect tablet from PC. Run it in Recovery by pressing VOLUME_UP and POWER buttons simultaneously.
9. Using VOLUME_UP button, select "Recovery" and confirm it by pressing VOLUME_DOWN button. Wait until TWRP Recovery starts.
10. In TWRP Recovery, select "Install ZIP" and point to "/external sd/UPDATE-SuperSU-v2.46.zip" (which we downloaded and placed on the root of the SD Card in Step 1)
11. After installation is finished, select "Reboot". Recovery will reboot the device.
12. After the device has rebooted successfully, you should see a new app named SuperSU in the application drawer.
Boom you have successfully rooted your device if you see the app! If you didn't see this app, you did something wrong and need to repeat the process
RESIZING OF THE PARTITION
This was the main reason why I wanted to root the T8 so badly as I was limited to only 2.9GB of internal storage.
1. Download Resize_v22.4.1-signed.zip and copy to the root of SD (without extracting)
2. Turn the device off and run Recovery by pressing VOLUME_UP and POWER button simultaneously.
3. Using VOLUME_UP button, select "Recovery" and confirm it by pressing "VOLUME_DOWN" button. Wait until TWRP Recovery starts.
4. In TWRP Recovery, select 'install ZIP' and point to "external sd/Resize_v22.4.1-signed.zip"
5. In one of following windows that pop up, select the partition size you desire. I went with 9GB and lost only the apps that I had moved manually to the SD Card.
Here's proof of my new 9GB internal storage after resizing:
Have fun!
Click to expand...
Click to collapse
Dear all,
I installed the xposed framework into the Cube T8, used the V80 and got a successful result.
Sorry I post the wrong position
Dear all,
I found a unoffical rom on CUBE OFFICAL WEBSITE, this rom inside a rom package called Cube T8 Plus FlymeOS adapt ROM(Just for Cube T8 Plus, not for T8)
, inside this package, you can find a file 合并分区线刷包, inside the file, T8-PLUS_20151224_ssd , this is the target file, unzip the file, and use computer usb to flash the rom with yours T8 plus., after flashing, finally, you will get a android 5.1 OS system, with Combined Data and SD Card partition, and A TWRP recovery, the OS not yet rooted, and also had been simplified, no google shop included, so your final job is install supersu to root it, and install Gapps zip file by recover Gapps zip file to get google shop........
Cube Tablet PC Firmware Upgrade website
http://www.51cube.com/ch/DownShow.asp?ID=392
Supersu download website
http://forum.xda-developers.com/showthread.php?t=1538053
Google Play install zip file website
http://highonandroid.com/download-android-5-1-lollipop-gapps/
Can not mount 32 GB SD card
Instructions
For insertion and mounting please?

[Tutorial] QHSUSB_DLOAD Hardbrick Fix for I9505

Hello.I had my phone updated from 4.2 to 4.3 a few days ago and after updating itself in recovery,it simply died.No charging,no battery pull reset,just plain dead.I connected it to my laptop and it recognised it as QHSUSB_DLOAD.After googling around i found that only a JTAG will save it.Well,that ain´t true.I will give you a tutorial that will fix your phone in a few minutes.
First of all,i did it on Windows 8.1 x64.
Prerequisites :
QDLoader HS USB Driver : x64 driver or x32 driver
I9505 Pit file : Pit file download
Boot repair tool : I9505 Boot repair tool
Needed files to enter download mode to flash a stock rom : Files for Download Mode
Stock ROM to flash.I used this one but IT IS FOR THE LTE VERSION. Please download the stock rom for the Non - LTE version if you have it.
And lastly,Odin : Download here
Step 1.
Make sure that your device is connected and in Device Manager , it show as QHSUSB_DLOAD .If it does,disconnect it from your computer.
Before installing the drivers,we need to disable driver signature enforcement.
First,press WinKey + C and choose Settings
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
or if you prefer the modern one in Windows 8.1 or Windows 10,choose Change PC Settings
Choose Update & recovery
Click Recovery
Then,at Advanced Startup,click Restart now.
Your PC will restart.
Click Troubleshoot
Advanced Options
Startup Settings
Once entered here,it will ask for us to restart.Click Restart
When at the list,press F7 to disable Driver signature enforcement and boot.
Step 2.
Install the 64 bit or 32 bit driver depending on your OS WITH YOUR DEVICE DISCONNECTED.
Now plug your device to your computer via USB and it should pop up in Device Manager as Qualcomm HS-USB QDLoader 9008
Next,go to Control Panel,choose Folder Options and check Show hidden files.
Make a new folder on your desktop and put the galaxy_S4_9505 boot repair QHUSB in that folder and nothing else.
Now extract the needed files for Download Mode in another folder and leave it open and the folder you have galaxy_S4_9505 boot repair QHUSB open aswell.
Open galaxy_S4_9505 boot repair QHUSB and do not click Recover Device until you read the next step.
Step 3.
This is the most important step because we will flash the stock boot files for our device.
With galaxy_S4_9505 boot repair QHUSB open and the two folders above open, select all the files in the needed files for Download Mode folder and be ready because when you click Recover device,you will need to drag those files in the folder where galaxy_S4_9505 boot repair QHUSB is and you have to be very fast when doing it.
Click Recover Device and drag the files in the folder mentioned above and click overwrite very fast.This should be done in 3 seconds max. and if it won´t work,repeat the last step until you do it right.
Your phone should now boot in Download Mode.
Step 4.
Download Odin and click on AP and select the .tar file and wait a few minutes.
Click on Options and check Auto Reboot , Re-Partition and F. Reset Time. Make sure that these are the only checked options.
Now go to Pit tab and select the downloaded pit file.
Click start and wait for it to finish.
That is it.
Final note :
If your device is restarting and it does not boots in Download mode and shows up that the battery is charging,disconnect it and pull the baterry and the press Vol. down , Home button and Power to enter Download mode.If you do not flash a stock ROM with Odin,after your first restart,it will become hardbricked again.
Don´t forget to hit that thanks button if it helped you.
Goodluck.
i can dbrick s4mini gt-i9195 please help
It will work with my Galaxy S4 Active (SHV-E470s)?
Can you force the QHSUSB_DLOAD
Help !!!
After trying the procedure, I did not timely drag the files !!! Now it turns green all the green screen, but when I connect it to the pc no holes detected no door !!! Can you force the QHSUSB_DLOAD or Qualcomm HS-USB QDLoader 9008 ???? Sorry my bad english !!!
It is also possible for s4 mini i9195 ????
Thank you so much ,it worked for me on Windows 7. Galaxy s4 I9505.
thank you soooooooooooooooooooooooo much.!?
video please please
After trying this method . Don't u suffer from any display problem ? I tried this and it worked for me but i have now display problem . it's a little yellow and it appears always download mode .
Can I backup my phone when in download mode?
i got status 29 error: system could not write the files to specified device please help
Can this be made for a i9195 model???
kent8hd said:
Hello.I had my phone updated from 4.2 to 4.3 a few days ago and after updating itself in recovery,it simply died.No charging,no battery pull reset,just plain dead.I connected it to my laptop and it recognised it as QHSUSB_DLOAD.After googling around i found that only a JTAG will save it.Well,that ain´t true.I will give you a tutorial that will fix your phone in a few minutes.
First of all,i did it on Windows 8.1 x64.
Prerequisites :
QDLoader HS USB Driver : x64 driver or x32 driver
I9505 Pit file : Pit file download
Boot repair tool : I9505 Boot repair tool
Needed files to enter download mode to flash a stock rom : Files for Download Mode
Stock ROM to flash.I used this one but IT IS FOR THE LTE VERSION. Please download the stock rom for the Non - LTE version if you have it.
And lastly,Odin : Download here
Step 1.
Make sure that your device is connected and in Device Manager , it show as QHSUSB_DLOAD .If it does,disconnect it from your computer.
Before installing the drivers,we need to disable driver signature enforcement.
First,press WinKey + C and choose Settings
or if you prefer the modern one in Windows 8.1 or Windows 10,choose Change PC Settings
Choose Update & recovery
Click Recovery
Then,at Advanced Startup,click Restart now.
Your PC will restart.
Click Troubleshoot
Advanced Options
Startup Settings
Once entered here,it will ask for us to restart.Click Restart
When at the list,press F7 to disable Driver signature enforcement and boot.
Step 2.
Install the 64 bit or 32 bit driver depending on your OS WITH YOUR DEVICE DISCONNECTED.
Now plug your device to your computer via USB and it should pop up in Device Manager as Qualcomm HS-USB QDLoader 9008
Next,go to Control Panel,choose Folder Options and check Show hidden files.
Make a new folder on your desktop and put the galaxy_S4_9505 boot repair QHUSB in that folder and nothing else.
Now extract the needed files for Download Mode in another folder and leave it open and the folder you have galaxy_S4_9505 boot repair QHUSB open aswell.
Open galaxy_S4_9505 boot repair QHUSB and do not click Recover Device until you read the next step.
Step 3.
This is the most important step because we will flash the stock boot files for our device.
With galaxy_S4_9505 boot repair QHUSB open and the two folders above open, select all the files in the needed files for Download Mode folder and be ready because when you click Recover device,you will need to drag those files in the folder where galaxy_S4_9505 boot repair QHUSB is and you have to be very fast when doing it.
Click Recover Device and drag the files in the folder mentioned above and click overwrite very fast.This should be done in 3 seconds max. and if it won´t work,repeat the last step until you do it right.
Your phone should now boot in Download Mode.
Step 4.
Download Odin and click on AP and select the .tar file and wait a few minutes.
Click on Options and check Auto Reboot , Re-Partition and F. Reset Time. Make sure that these are the only checked options.
Now go to Pit tab and select the downloaded pit file.
Click start and wait for it to finish.
That is it.
Final note :
If your device is restarting and it does not boots in Download mode and shows up that the battery is charging,disconnect it and pull the baterry and the press Vol. down , Home button and Power to enter Download mode.If you do not flash a stock ROM with Odin,after your first restart,it will become hardbricked again.
Don´t forget to hit that thanks button if it helped you.
Goodluck.
Click to expand...
Click to collapse
Plz help me i am using this tutorial to fix my p5100 device but it shows permission denied . Other then samsung note 4 repair tool , I got appropriate things for my device. Plz help
Thank you a lot! It worked!
It took me a bit of time, this is my extra info for others:
- When doing the step 3, a command window with scrolling text will appear with 2 lines. You must do the copy paste thing BEFORE the text starts rolling as that indicates it started using those files. If no window with text opens, try again
- With odin I had 2 problems: One, that it was failing to do the copying, the reason was that I was using a wrong ROM. Second was that a ROM was written, but it was the incorrect one so I had to start again from step 0.
So try a different ROM.
I read the cable may be a problem too, but it wasn't in my case.
In between retries and after succeeding, removing the usb cable AND the battery may help.

(GUIDE:) How to ROOT the TAB S6 - SM-T860 (Wi-Fi Model) - (12/10/21):

Hello all,
BORING INTRO STUFF (Safely Ignore This):
I couldn't find any guide that was current enough to make me feel confident in going through with rooting this tablet. So because of that, I decided I would make on my own guide for those that needed this. I tried multiple guides here and all of them resulted in a boot-loop.
VERY SMALL PSA: I'm apologizing in advance if this guide is both pointless and longer than it needs to be. I figured it would be useful as a future reference in-case anyone needed this.
THINGS YOU WILL NEED:
* TAB S6 - SM-T860 (Wi-Fi)
* This can be done on Android 9,10 & 11 (Process is the same)
* Your specific firmware downloaded (*DO NOT SKIP THIS*)
* Tablet is charged to at least 50%
* Maximum of 20 minutes to both read & follow the process
* FIRMWARE: The link below is the firmware I used. I would still advise you to both look for your specific version and to use the link provided below only if your tablet is exactly as followed:
* (T860XXU4CUI4) - BUILD NUMBER
* (ANDROID 11) - ANDROID VERSION
* (XAR - CELLUAR SOUTH) - SERVICE PROVIDER SOFTWARE VERSION
( https://samfirms.com/SM-T860/KOR/T860XXU4CUI4 )
* SAMSUNG USB DRIVERS: ( https://developer.samsung.com/android-usb-driver )
* ODIN: ( https://samfirms.com/download-odin ) Latest is 3.14.4. Use that one or the newest one
* TWRP (OPTIONAL): T860 (Wi-Fi) ONLY. DOWNLOAD VERSION "twrp-3.6.0_9-0-gts6lwifi.img.tar" OR THE LATEST ONE AVAIABLE.
( https://dl.twrp.me/gts6lwifi/ )
* MAGISK APP: ( https://magiskmanager.com/downloading-magisk-manager )
* LZ4 TOOL: ( https://github.com/lz4/lz4/releases )
* 7-ZIP: ( https://www.7-zip.org/download.html )
HOW TO ROOT:
1. UNLOCKING THE BOOTLOADER: *** THIS WILL WIPE YOUR DATA *** (GO TO SETTINGS > ABOUT TABLET > SOFTWARE INFORMATION & TAP BUILD NUMBER 7 TIMES. GO TO DEVELOPER OPTIONS > TOGGLE ON OEM UNLOCKING) TURN OFF THE TABLET. AT YOUR PC, HAVE A CABLE CONNECTED TO THE PC. WHILE HOLDING BOTH VOLUME DOWN + VOLUME UP, PLUG IN THE CABLE. WHEN THE SCREEN TURNS ON, PRESS AND HOLD VOLUME UP.
WHEN THE SCREEN CHANGES PROMOTING YOU TO UNLOCK THE BOOTLOADER, PRESS VOLUME UP. ONCE BOOTED UP, GO THROUGH THE SETUP AGAIN AND MAKE SURE Wi-Fi IS CONNECTED. GO BACK TO SETTINGS, ENABLE DEVELOPER OPTIONS AGAIN AND THEN ENABLE USB - DEBUGGING.
2. EXTRACT THE BOOT.IMG.LZ4 FILE AND MOVE IT TO YOUR TABLET: After 7-Zip is installed, the LZ4 Tool and the firmware you downloaded is extracted somewhere, open the extracted firmware folder. Right-click on the AP file and select 7-zip then open archive. Look for boot.img.lz4, drag it inside of the LZ4 Tool. Once done, drag the boot.img.lz4 on top of the LZ4 executable. It will be extracted as boot.img. Right-click the boot.img file and select 7-zip then add to archive. Change "Archive format" to tar and rename it to boot.tar. Finally, move it to your tablet's storage.
3. DOWNLOAD THE MAGISK APK: Install the Magisk apk that you downloaded and open it up. Within the app, select install, uncheck recovery mode and press next then check "Select and Patch a file". Locate your boot.tar file that you moved into your storage from earlier and wait for Magisk to process it.
4. USING ODIN: Go ahead and locate the new file, it starts with Magisk (NOT THE BOOT.TAR FROM EARLIER SHOULD START WITH MAGISK). Once done, move the Magisk tar file to your computer and turn off the tablet. With the tablet off and Odin open (Run as administrator) , press and hold both VOLUME DOWN & VOLUME UP then plug the cable from your pc into your tablet. With Odin open, go into the "options" tab, uncheck "Auto Reboot" and Select "AP". Locate the Magisk tar file you moved from your tablet and then press "Start".
ONCE IT SAYS "PASS" THEN STOP AND READ THIS BEFORE CONTINUING. *IMPORTANT*
PRESS AND HOLD BOTH POWER AND VOLUME DOWN FOR 7 SECONDS. THE SCREEN WILL TURN BLACK. VERY QUICKLY WHILE STILL HOLDING POWER, PRESS AND HOLD VOLUME UP INSTEAD. PRESS POWER TO THE BOOTLOADER UNLOCK PROMPT AND YOU SHOULD BE IN RECOVERY. THIS SHOULD BOOT YOU INTO STOCK RECOVERY. USE THE VOLUME KEYS TO NAVIGATE, SELECT "Wipe data/factory reset" then press the power button and select "Factory data reset". Finally, select "Reboot system now" and Wait for the tablet to reboot into the OS.
5. FINISHING UP: After the tablet has restarted back into android and you took a couple of minutes to go through the setup one last time. Scroll up into the app drawer and make sure that you see the app "Magisk", go ahead and select it and press ok to download Magisk. Afterwards, open it up and Magisk will ask you to reboot to finish setting up root. Press ok. Once restarted you are done with the rooting process.
Lastly, as an optional step you can install TWRP.
6. TWRP INSTALLATION (OPTIONAL): With the tablet off and Odin running on your pc, go ahead and press VOLUME DOWN AND VOLUME UP at the same time then plug in the data cable from your PC. Press VOLUME UP to go into download mode. Once in download mode, select "AP" then select the TWRP tar file you downloaded and make sure to uncheck "Auto reboot" from the options tab in Odin. Click start and after it says "PASS" unplug the data cable. On the tablet, press VOLUME DOWN AND POWER to reboot and when you see THE SCREEN TURN BLACK, QUICKLY PRESS AND HOLD BOTH POWER AND VOLUME UP. You should be in TWRP and you are now officially done.
* From now on, I would recommend you use the Magisk app or some reboot app to boot into recovery as it is difficult to use the button combinations to access recovery.
* IF YOU'RE NOT USING MAGISK TO REBOOT TO RECOVERY, I WOULD USE THIS APP INSTEAD: https://play.google.com/store/apps/details?id=com.eypcnnapps.quickreboot&hl=en_US&gl=US
Credits: If all went well then I appreciate you taking the time to read through this guide carefully. Hope it was as clear as possible and that you found it helpful. I will be editing this post from time to time to make it cleaner.
Again, Thank you and if you have any questions, I will answer them when I see them.
THANK YOU SO MUSH IVE BEEN STRUGGLING SO HARD TO GET ROOT ON THIS TABLET FINALLY THANK YOUUUUUU
by the way guys, when it says to reboot to make magisk work.
you are risking a bootloop.
Oh by the way, aside from TWRP being wonky thank you for the guide I had been playing with the idea of rooting this thing for over a year now. You made it easy.
I go through all the steps and it works fine. Once I try for TWRP I end up with
"partition recovery
Reason recovery: Error verifying vbmeta image: invalid vbmeta header (6)
CUSTOM recovery
VBMETA T860XXU4DVG6, 54204454R"
From that point it just loops back to that message and downloading mode until I wipe it all and start over again. I TWRP a no go for the S6 now? I guess I can dig around on their site as well. Any input anyone wants to throw my way will also be appreciated.
Hi Sadistic - ,
I need to start with a complement. This is a really clear guide.
But, When I get done with step 3, the Magisk patched boot file has a .img extension
On step 4, Odin is expecting a .tar file extension so the file doesnt show up.
Did I miss something?
Thanks
mvanwey said:
Hi Sadistic - ,
I need to start with a complement. This is a really clear guide.
But, When I get done with step 3, the Magisk patched boot file has a .img extension
On step 4, Odin is expecting a .tar file extension so the file doesnt show up.
Did I miss something?
Thanks
Click to expand...
Click to collapse
Yep..... try step 2
seppukuudere said:
Yep..... try step 2
Click to expand...
Click to collapse
Yes, step 2 is moving the extracted boot file (re-named to .tar) to my tablet and then patching it with magisk.
The patched file from Magisk has an .img extension.
mvanwey said:
Yes, step 2 is moving the extracted boot file (re-named to .tar) to my tablet and then patching it with magisk.
The patched file from Magisk has an .img extension.
Click to expand...
Click to collapse
Ah I see, I would try to do step 3 again, take screenshots of the end result from magisk o:
Let's just cancell this. it was over 20 days since I asked for help & now I'm getting asked for screenshots.
I have moved on.
I probably should have put that in my reply.
mvanwey said:
Let's just cancell this. it was over 20 days since I asked for help & now I'm getting asked for screenshots.
I have moved on.
I probably should have put that in my reply.
Click to expand...
Click to collapse
oops yikes, yeah probably should have. happy new year!
seems like after rooting mine the storage has been cut by a big margin, from 128 to 32gb. any way of fixing this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hi. Is there any update guide for last android 12 version, to install twrp? Can se still use this, as it is for android 11?
Thanks,

[GUIDE] How to Root Samsung Galaxy J8 and Flash TWRP - J810F/G/M/Y/GF - j8y18lte

{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
GUIDE TO FLASH TWRP AND ROOT SAMSUNG GALAXY J8
YOU ARE THE SOLE RESPONSINLE FOR WHAT HAPPENS TO YOUR DEVICE. PROCEED WITH CAUTION!
WARNING!​Always keep your stock firmware files on your computer. If you mess up your device, you must re-flash your stock rom. Do not forget that you will lose your data in the process rooting!
Sites to get official Samsung stock firmwares:
https://samfw.com (no login required, unlimited speed)
https://samfrew.com (no login required, limited speed)
https://www.sammobile.com (login required, limited speed)
​GETTING STARTED​1. ENABLE DEVELOPER OPTIONS: Go to Settings -> About Phone -> Software Information and tap “Build Number” 4-5 times to unlock developer options.
2. UNLOCK BOOTLOADER: Go to Settings -> Developer Options -> enable OEM Unlocking (this will format your data).
Download the following files to your computer:
1. TWRP-v3.5.0-j8y18lte-goldfish07.tar: https://tinyurl.com/J8-TWRP
2. Odin3_v3.14.4.zip: https://tinyurl.com/J8-ODIN
3. Magisk-v24.3-flash.zip: https://tinyurl.com/J8-FLASH-MAGISK
4. Magisk-v24.3-app.apk: https://tinyurl.com/J8-APP-MAGISK ​5. AnyKernel3-j8y18lte-goldfish07.zip: https://tinyurl.com/J8-ANYKERNEL
6. tryfix_j8_lockscreen.zip: https://tinyurl.com/J8-LOCKSCREEN-FIX
​FLASHING TWRP​1. Extract Odin flash tool and start the program. DO NOT CHANGE ANY OPTIONS, THEY ARE ALREADY CONFIGURED!
2. Turn off your phone. Press and hold ONLY volume up and volume down buttons, NOT POWER BUTTON. While holding volume up and volume down buttons, connect the phone to computer using USB cable. Your phone will boot into download mode. Then you can stop pressing volume buttons. It will ask you to press volume up button ONCE. Finally, you will see the download mode interface. Check the Odin app, you should see ID:COM place has one recognised device and also, check “Message” box. You should see “ID:…/… Added!” message. If you cannot see it, try disconnecting and connecting your phone to computer again. If you still cannot see it, try installing USB drivers from here: https://tinyurl.com/J8-USB-DRIVERS
3. On Odin sections, click on “AP” and select TWRP-v3.5.0-j8y18lte-goldfish07.tar file.
4. Now, click on “Start” and wait for TWRP to be flashed.
5. If TWRP is flashed correctly, you will see green “Pass” message.
6. When you see pass message, disconnect the phone from computer. Press and hold volume down and power keys until screen goes off and SUDDENLY start pressing ONLY volume up and power buttons until the phone boot into TWRP. If you do it wrong, press and hold volume up, volume down and power buttons until the phone shuts down. Then again, press and hold volume up and power buttons until it boots into TWRP.
7. When you boot into TWRP for the first time it will ask you “Keep System Read Only?”. Check the box of “Never show this screen during boot again” and “Swipe to Allow the Modifications”. You will see the TWRP options. Go into “Settings” then check “Skip Digest generation during backup” and uncheck “Unmount System before installing a ZIP”. Go back to main TWRP menu. Go to “Wipe”-“Format Data” and type yes in the box and apply it.
​ROOTING​1. Go back to main TWRP menu and select “Mount”. In the section of “Select Partitions to Mount” select ALL the options, System, preload, Data etc. Then go back to main TWRP menu.
2. Either connect the phone to computer, use USB OTG or Micro SD card to copy these files to the phone: “Magisk-v24.3-flash.zip”, “Magisk-v24.3-app.apk”, “AnyKernel3-j8y18lte-goldfish07.zip”, “tryfix_j8_lockscreen.zip”.
2. Go to “Install”, press “Select Storage” and pick the one you copied the files (Internal Storage, Micro SD card or USB OTG) and press “OK”.
3. Select “AnyKernel3-j8y18lte-goldfish07.zip” DO NOT check “Zip signature verification” and “Reboot after installation is complete” and “Swipe to confirm Flash”. When it is done, DO NOT select “Wipe Cache/Dalvik” or “Reboot System”. Just press back button ONCE to go back to “Install” menu.
3. Now, select “Magisk-v24.3-flash.zip” and flash it the same way you flashed “AnyKernel3-j8y18lte-goldfish07.zip”. When flashing is complete, just press back button ONCE to go back to “Install” menu.
4. Then, select “tryfix_j8_lockscreen.zip” and flash it the same way you flashed previous zips. When flashing is complete, select “Reboot System” and wait the phone to start normally.
5. When the phone starts, complete the setup process and install “Magisk-v24.3-app.apk”. Connect to internet, start Magisk app, wait a few seconds and it will ask you to reboot once. Say okay and let it reboot.
6. Enjoy!
​Special Note: If you want to use a faster, lighter, preconfigured, simpler and updated stock rom with VOLTE, I strongly suggest you to use debloated rom: https://forum.xda-developers.com/t/...stock-rom-v7-j810f-g-m-y-gf-j8y18lte.4478935/
Contributors
goldfish07 (Ayush Bisht) for anykernel and TWRP
topjohnwu for Magisk
osm0sis for anykernel
kapmino269 for lockscreen fix
Reserved
BNFCTR said:
Go into “Settings” then check “Skip Digest generation during backup” and uncheck “Unmount System before installing a ZIP”.
Click to expand...
Click to collapse
I assume we leave "Use SHA2 for hashing" checked as well. So just two boxes checked.
BNFCTR said:
ROOTING​1. Go back to main TWRP menu and select “Mount”. In the section of “Select Partitions to Mount” select ALL the options, System, preload, Data etc. Then go back to main TWRP menu.​
Click to expand...
Click to collapse
Any reason I can't check "USB OTG"?
I get mounting errors later if I don't check it, but it isn't letting me
Any ideas? Thanks
(End up in an infinite start loop if I ignore the errors)
Canyoning.cat said:
I assume we leave "Use SHA2 for hashing" checked as well. So just two boxes checked.
Any reason I can't check "USB OTG"?
I get mounting errors later if I don't check it, but it isn't letting me
Any ideas? Thanks
(End up in an infinite start loop if I ignore the errors)
Click to expand...
Click to collapse
Yes, leave SHA2 checked. If possible, try using another otg device to check whether the issue persists.
Maybe this is a silly question but if I'm just connecting my phone to my laptop using a micro USB cable, do I need to check OTG? I'm not using an OTG cable to connect a flash drive...
The error i keep getting if this:
"Failed to mount '/odm' (no such file or directory)"
Canyoning.cat said:
Maybe this is a silly question but if I'm just connecting my phone to my laptop using a micro USB cable, do I need to check OTG? I'm not using an OTG cable to connect a flash drive...
The error i keep getting if this:
"Failed to mount '/odm' (no such file or directory)"
Click to expand...
Click to collapse
1. You can and you should check usb otg option in mount only if you connect a usb drive using an otg cable.
2. /odm error does not affect anything. It gives that error at first and then disappears. You should not worry about it.
I couldn't resolve the boot loop, so ended up flashing the debloated rom (https://forum.xda-developers.com/t/...stock-rom-v7-j810f-g-m-y-gf-j8y18lte.4478935/). Working well thus far
Thanks for all the work everyone has put into these!
stop samsung logo only ..
do you have a video this tutorial for rooting samung j810y thank you very much
jonardmhou said:
stop samsung logo only ..
Click to expand...
Click to collapse
Please follow the steps carefully.
jonardmhou said:
do you have a video this tutorial for rooting samung j810y thank you very much
Click to expand...
Click to collapse
Unfortunately no.
not working on
I have correctly flashed twrp now the problem is that I cannot access it and I tried everything to use the 3 buttons at the same time, volume down and power button, volume up and power button and turn off then turn on release power and leave the two volume buttons and it always goes to factory recovery. Any idea what else I can do?
first of all, Thanks
model: j810MUBU3CWB1
dieg0802 said:
I have correctly flashed twrp now the problem is that I cannot access it and I tried everything to use the 3 buttons at the same time, volume down and power button, volume up and power button and turn off then turn on release power and leave the two volume buttons and it always goes to factory recovery. Any idea what else I can do?
first of all, Thanks
model: j810MUBU3CWB1
Click to expand...
Click to collapse
answered me, installed sky hawak SHRP-v2.3.2-J8y18lte-goldfish07-Odin-AP correctly and opened correctly android 10
dieg0802 said:
answered me, installed sky hawak SHRP-v2.3.2-J8y18lte-goldfish07-Odin-AP correctly and opened correctly android 10
Click to expand...
Click to collapse
i also did it with sky hwak but now my phone only boots in shy hawk recovery and does not boot to normal rom (it does not goes further )
can i get help so i get access my phone normally , without getting stuck at recovery ?

Unable to root my phone because i cant see the necessary files for it, where do i request it here?

Hi! I'm new here. Just read the post for newbies and tried to search for a forum for my Infinix phone but I cannot find one.
If anyone knows if threads or forums related to infinix phones please let me know, thank you.
MAIN QUESTION:
Okay so ive landed here because i wanted to root my new phone, ive done it already once only because my old phone was really old so i was able to find the necessary files.
I am wondering who can i send a request to either help me find/make the necessary file like the usb driver for the specific phone as well as the image /flash file(sorry forgot the correct term)
so i can proceed with rooting my phone
Also, the senior contributors that i was supposed to ask are labelled inactive.
Phone brand&model: Infinix Hot 20 X6826C
Android version: 12
for mediatek devices use mtkclient to read partitions off device.
alecxs said:
for mediatek devices use mtkclient to read partitions off device.
Click to expand...
Click to collapse
I did a quick search and altough i cannot quite comprehend the jargons, if my assumptions are correct, mtkclient is a tool to help root my phone, correct?
EDIT: so it looks like i need a flash image or file, where do i get it? cant seem to find one(or maybe i missed it because i dont exactly know what im trying to find yet)
im unsure but i think it's this link:
Download Infinix Stock ROM for all models (Latest Firmware)
Download the latest Infinix Stock ROM Firmware (Flash File) for all the available Infinix smartphones, feature phones, and tablets.
androidmtk.com
but still can anyone confirm if im finding the correct file
alecxs said:
for mediatek devices use mtkclient to read partitions off device.
Click to expand...
Click to collapse
mtkclient is a flash tool that works similar to SP Flash Tool, but without scatter file. you can use it to read boot partition off device.
https://github.com/bkerler/mtkclient#read-flash
r = read
Code:
python mtk r boot boot.img
alecxs said:
mtkclient is a flash tool that works similar to SP Flash Tool, but without scatter file. you can use it to read boot partition off device.
https://github.com/bkerler/mtkclient#read-flash
r = read
Code:
python mtk r boot boot.img
Click to expand...
Click to collapse
it looks liek it wants me to enter recovery mode to proceed with he command but when i did it just throws me this, ive no idea what is brom or prelaoder mode
Code:
Port - Hint:
Power off the phone before connecting.
For brom mode, press and hold vol up, vol dwn, or all hw buttons and connect usb.
For preloader mode, don't press any hw button and connect usb.
If it is already connected and on, hold power for 10 seconds to reset.
"Power off the phone before connecting.
For brom mode, press and hold vol up, vol dwn."
(use an online translator or ask a nearby person help you to understand)
alecxs said:
"Power off the phone before connecting.
For brom mode, press and hold vol up, vol dwn."
Click to expand...
Click to collapse
still unsuccesful though
Code:
C:\Users\hanzo\AppData\Local\Programs\Python\Python39\mtkclient>python mtk r boot,vbmeta boot.img,vbmeta.img
MTK Flash/Exploit Client V1.6.2 (c) B.Kerler 2018-2023
DeviceClass
DeviceClass - [LIB]: ←[31mCouldn't get device configuration.←[0m
Preloader - Status: Waiting for PreLoader VCOM, please connect mobile
Port - Hint:
Power off the phone before connecting.
For brom mode, press and hold vol up, vol dwn, or all hw buttons and connect usb.
For preloader mode, don't press any hw button and connect usb.
If it is already connected and on, hold power for 10 seconds to reset.
PreLoader VCOM drivers installed? can you see phone in device manager when plugged in power off state?
alecxs said:
PreLoader VCOM drivers installed? can you see phone in device manager when plugged in power off state?
Click to expand...
Click to collapse
yes, ive installed it as far as i know with the help of this Website, did both the manual and the automatic
but unfortunately i still cant find my device on device manager on power off state
(intentionally left those devices just to show that ive installed the drivers)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
okay so i've downloaded a stock rom for my specific phone model can i use that instead to extract boot.img(will only use this as last resort)
yes, if it is the same build/release you can use it from download. double check from settings - about phone.
regarding VCOM preloader drivers, I can see you haven't installed correctly (yellow triangles)
you can assign the *.inf manually in device manager. make sure phone is powered off. keep an eye for new device in device manager, connect the usb cable.
preloader is only visible for ~1 second, it disappears immediately when phone gets power of usb. during this second, pick the new device in device manager, click on > Properties > Update Driver > Browse my computer for driver software > Let me pick from the list of device drivers on my computer > Show all devices > Have Disk > cdc-acm.inf
Now each time you connect phone in power off state, preloader is ready to get connected to flash tool for ~ 1 second.
alecxs said:
yes, if it is the same build/release you can use it from download. double check from settings - about phone.
regarding VCOM preloader drivers, I can see you haven't installed correctly (yellow triangles)
you can assign the *.inf manually in device manager. make sure phone is powered off. keep an eye for new device in device manager, connect the usb cable.
preloader is only visible for ~1 second, it disappears immediately when phone gets power of usb. during this second, pick the new device in device manager, click on > Properties > Update Driver > Browse my computer for driver software > Let me pick from the list of device drivers on my computer > Show all devices > Have Disk > cdc-acm.inf
Now each time you connect phone in power off state, preloader is ready to get connected to flash tool for ~ 1 second.
Click to expand...
Click to collapse
i did instructions but it still disappears tho resulting in same stuff appering when i try the read command on mtkclient
i keep getting this instead
Code:
C:\Users\hanzo\AppData\Local\Programs\Python\Python39\mtkclient>python mtk r boot_b boot_b.img
MTK Flash/Exploit Client V1.6.2 (c) B.Kerler 2018-2023
DeviceClass
DeviceClass - [LIB]: ←[31mCouldn't get device configuration.←[0m
Preloader - Status: Waiting for PreLoader VCOM, please connect mobile
can you see preloader in device manager? is it visible without any yellow triangle exclamation mark?
alecxs said:
can you see preloader in device manager? is it visible without any yellow triangle exclamation mark?
Click to expand...
Click to collapse
yes, i am able to see it but it only lasts like 1 sec and then it refresges and poof! its gone then the same problem occurs again
do note that
at the moment the device appears when i plug it in, i quickly entered the code
then theres a big delay then after a few minutes i'l get the same errors again
you do the opposite - first start reading/flashing, then connect phone
alecxs said:
you do the opposite - first start reading/flashing, then connect phone
Click to expand...
Click to collapse
just keeps throwing this error
Code:
..DeviceClass
DeviceClass - [LIB]: ←[31mCouldn't get device configuration.←[0m
.........
so double check build/release number from settings - about phone. then find a download for this ROM.
alecxs said:
so double check build/release number from settings - about phone. then find a download for this ROM.
Click to expand...
Click to collapse
just wanna make sure, aside from build / release number, what other aspects should i consider when downloading stock rom
alecxs said:
so double check build/release number from settings - about phone. then find a download for this ROM.
Click to expand...
Click to collapse
i have downloaded a stock rom but i still aint using it because:
The rom file is named: ""Infinix_Hot_20_X6826C_MT6768_V826_230314.zip""
the build number is "X6826C-H6927ABC-S-OP-230314V826" it somehow manage to match with ""... v826_230314" and "X6826C" on the downloaded stock rom file name, BUT
on the downloaded stock rom file too, there is this thing called "MT6768" but my cpu is "MT6769V/CZ" should i worry about it?

Categories

Resources