Hi,
I was on Oxygen OS 10.0.0. Rooted with twrp-3.3.1-4-enchilada and magisk 20.1. (I had used this guide to do it. https://forum.xda-developers.com/oneplus-6/how-to/how-to-flash-twrp-magisk-android-10-t3988213) Today I downloaded the zip for 10.0.1 from the Oxygen Updater app and tried to flash it like I have done for OOS 9 in the past as usual. I went to recovery (I did not backup), I just wiped my data (not internal storage), cache and system. After that I tried to install the new zip but I got an error. It just said error unable to install. Didn't mention why. I tried flashing the older OOS 10 zip and got the same error.
So I thought I will try flashing on the other slot. I was on slot B. I switched to slot A and got the same error.
So I thought I will try to sideload. When I tried that I got the same error. So I thought I will try to reflash the twrp img itself. I went to fastboot mode and tried runnning this command
fastboot boot twrp-3.3.1-14-enchilada-Q-mauronofrio.img
It showed me this error
Sending 'boot.img' (65536 KB) OKAY [ 1.609s]
Booting FAILED (remote: 'unknown command')
fastboot: error: Command failed
Now I don't have any recovery at all. I have just the unlocked bootloader and no OS nor recovery. What can I do to flash TWRP again and install either OOS 10.0.1 zip or 10.0.0 zip? Any help will be great.
Thanks
Arnavzz said:
Hi,
I was on Oxygen OS 10.0.0. Rooted with twrp-3.3.1-4-enchilada and magisk 20.1. (I had used this guide to do it. https://forum.xda-developers.com/oneplus-6/how-to/how-to-flash-twrp-magisk-android-10-t3988213) Today I downloaded the zip for 10.0.1 from the Oxygen Updater app and tried to flash it like I have done for OOS 9 in the past as usual. I went to recovery (I did not backup), I just wiped my data (not internal storage), cache and system. After that I tried to install the new zip but I got an error. It just said error unable to install. Didn't mention why. I tried flashing the older OOS 10 zip and got the same error.
So I thought I will try flashing on the other slot. I was on slot B. I switched to slot A and got the same error.
So I thought I will try to sideload. When I tried that I got the same error. So I thought I will try to reflash the twrp img itself. I went to fastboot mode and tried runnning this command
fastboot boot twrp-3.3.1-14-enchilada-Q-mauronofrio.img
It showed me this error
Sending 'boot.img' (65536 KB) OKAY [ 1.609s]
Booting FAILED (remote: 'unknown command')
fastboot: error: Command failed
Now I don't have any recovery at all. I have just the unlocked bootloader and no OS nor recovery. What can I do to flash TWRP again and install either OOS 10.0.1 zip or 10.0.0 zip? Any help will be great.
Thanks
Click to expand...
Click to collapse
So basically what happened there is TWRP doesn't boot with the oxygenos 10 bootloader. You will need to use the MSM download tool to unbrick your device.
Sent from my ONEPLUS A6003 using Tapatalk
Kaleshwar said:
So basically what happened there is TWRP doesn't boot with the oxygenos 10 bootloader. You will need to use the MSM download tool to unbrick your device.
Sent from my ONEPLUS A6003 using Tapatalk
Click to expand...
Click to collapse
But how is that? I was on stable OOS 10 before rooting following this link https://forum.xda-developers.com/oneplus-6/how-to/how-to-flash-twrp-magisk-android-10-t3988213. As per this, the first step is to flash twrp and that image did flash back when I did it. Any idea why it doesn't work now?
Also, do you have any links for the MSM download tool and any guide if there is?
Thanks
Arnavzz said:
But how is that? I was on stable OOS 10 before rooting following this link https://forum.xda-developers.com/oneplus-6/how-to/how-to-flash-twrp-magisk-android-10-t3988213. As per this, the first step is to flash twrp and that image did flash back when I did it. Any idea why it doesn't work now?
Also, do you have any links for the MSM download tool and any guide if there is?
Thanks
Click to expand...
Click to collapse
The problem isn't TWRP it's the bootloader. That's all I know. And for the MSM download tool. See attached link below.
https://forum.xda-developers.com/oneplus-6/how-to/tool-msmdownloadtool-v4-0-international-t3798892
Sent from my ONEPLUS A6003 using Tapatalk
Do not boot the twrp from fastboot it won't work
Just do
Fastboot flash boot twrp.img
Then reboot the device to twrp it will boot to trwp and then flash the new a10 zip and immediately afterwards flash the twrp zip
chintu1234 said:
Do not boot the twrp from fastboot it won't work
Just do
Fastboot flash boot twrp.img
Then reboot the device to twrp it will boot to trwp and then flash the new a10 zip and immediately afterwards flash the twrp zip
Click to expand...
Click to collapse
This doesn't work. It flashes successfully but when I select Reboot Recovery and press the power button, it boots back to the bootloader.
Maybe wrong twrp img
Try the older 3.3.1-12 twrp.img and then try
Also try the following as well
Fastboot flash boot_a twrp.img
Fastboot flash boot_b twrp.img
And try just reboot not reboot to recovery
Kaleshwar said:
The problem isn't TWRP it's the bootloader. That's all I know. And for the MSM download tool. See attached link below.
https://forum.xda-developers.com/oneplus-6/how-to/tool-msmdownloadtool-v4-0-international-t3798892
Sent from my ONEPLUS A6003 using Tapatalk
Click to expand...
Click to collapse
Thanks so much for that! I have been able to recover the phone using MSM download tool. Now will update to 10 using the phones OTA.
However, I have one question, if I update to OOS 10.0.1, do you think this original post on rooting OOS 10, will work for it? https://forum.xda-developers.com/oneplus-6/how-to/how-to-flash-twrp-magisk-android-10-t3988213 Or do you suggest to not root and wait?
Arnavzz said:
Thanks so much for that! I have been able to recover the phone using MSM download tool. Now will update to 10 using the phones OTA.
However, I have one question, if I update to OOS 10.0.1, do you think this original post on rooting OOS 10, will work for it? https://forum.xda-developers.com/oneplus-6/how-to/how-to-flash-twrp-magisk-android-10-t3988213 Or do you suggest to not root and wait?
Click to expand...
Click to collapse
You can try it . Looks pretty solid.
Sent from my ONEPLUS A6003 using Tapatalk
Put the TWRP zip and stock boot img on phone (a TWRP img is not a TWRP zip)
Remove Magisk modules first to avoid issues (in TWRP if you cannot boot to system. https://forum.xda-developers.com/showpost.php?p=72542167&postcount=242)
Update through local update to 10.3.2 is what I prefer to do. Then I do the following.
Reboot to let phone finish whatever. reboot into bootloader.
1. Fastboot TWRP img - fastboot flash boot twrp-3.3.1-18-enchilada-Q-mauronofrio.img - ( https://sourceforge.net/projects/ma...3.3.1-18-enchilada-Q-mauronofrio.img/download )
2. Use volume up to recovery and power button to boot to recovery
3. Flash 10.3.2 stock boot img while in TWRP (or current ROM stock boot img).
4. Flash TWRP zip while in TWRP (https://sourceforge.net/projects/ma...-enchilada-installer-mauronofrio.zip/download ) or Blu zip (https://github.com/engstk/android_device_oneplus_enchilada/releases)
5. Reboot to recovery
6. Flash Magisk 20.3 while in TWRP
(Flash a Q kernel if you want one other than stock)
7. Reboot system
You are now rooted
Stock boot 10.3 img
https://mega.nz/#!PO5x1bYA!dKq3pbxUdpb16zhuqM_idqvWNLnsu4Ky4IAmYQiQUDw
Most stock boot imgs
https://forum.xda-developers.com/oneplus-6/how-to/patched-boot-image-magisk-16-7-beta-t3818853
I had similar situation last evening.
I made the mistake of having a factory reset on rooted 9.0.8 and then trying to flash the 10.0.1
I got the same error, so I had to connect my mobile to my laptop, fastboot to the newest TWRP, flash the TWRP, flash the 9.0.9, flash the 10.0.1, flash magisk 20.x and then everything was working.
xpakage said:
Put the TWRP zip and stock boot img on phone (a TWRP img is not a TWRP zip)
Remove Magisk modules
Update through local update 10.3 or current ROM
Reboot
1. Fastboot TWRP img - fastboot flash boot twrp-3.3.1-16-enchilada-Q-mauronofrio.img - ( https://androidfilehost.com/?fid=4349826312261678088 )
2. Use volume up to recovery and power button to boot to recovery
3. Flash 10.3 stock boot img while in TWRP (or current ROM stock boot img).
4. Flash TWRP zip while in TWRP ( https://androidfilehost.com/?fid=4349826312261678087 ) or Blu zip (https://github.com/engstk/op6/releases/download/r112/blu_spark_r112-oos_op6-op6t_0dd5f9228.zip)
5. Reboot to recovery
6. Flash Magisk 20.1 while in TWRP
(Flash a Q kernel if you want one other than stock)
7. Reboot system
You are now rooted
Stock boot 10.3 img
https://drive.google.com/file/d/1w44cUg815g-H1h_6gObUVPLDTc_dtiMX/view
Most stock boot imgs
https://forum.xda-developers.com/oneplus-6/how-to/patched-boot-image-magisk-16-7-beta-t3818853
Click to expand...
Click to collapse
This worked for me.. Finally. PS - I did in a slightly different order. I installed twrp first, booted into twrp, made sure I was in slot A. If I wasnt, I rebooted to recovery. If I still wasnt I set slot to A manually then rebooted to recovery again. Flashed the stock boot img you linked to boot, then rebooted to recovery slot b (same process I did to get to slot a) then flashed the stock boot img to boot again THEN finally installed magisk. Booted to system, where it hanged a bit, rebooted before getting into android, but booted in just fine after that..
For some reason if you don't flash stock img to slot A (and maybe slot B too, I did this for good measure) before installing magisk everything dies a horrible death and breaks, which can't even be recovered from /boot /system backups..
EDIT: Tried to reboot into recovery, which reverted back to stock for some reason after doing the above steps. So I proceeded to install the bluspark recovery, rebooted into recovery, made sure I was in slot b, made a back up of the boot image, then flashed bluspark kernel. Got stuck at the unlocked bootloader screen. Rebooted into recovery, restored my /boot back. Still stuck when I try to boot into system. Fixed it by booting back into recovery in slot A flashing stock boot img, then into slot b stock boot, then magisk, but also installed bluspark kernel here because I had a feeling I would lose twrp from flashing to stock boot img, and that the issue was caused by twrp (both twrp-3.3.1-16-enchilada-installer-mauronofrio and twrp-3.3.1-x_blu_spark_v9.108_op6 have this issue). Guess what? Turns out I was right. Having twrp breaks everything after you install magisk, so you need to flash the stock boot img before flashing magisk for some reason.. and cant install twrp again unless you dont mind bricking your phone.
EDIT2: F2FS works, just boot into recovery via fastboot (this should be slot b), change /data to f2fs, boot back into fastboot then into recovery again by fastboot (slot b again), flash stock boot img > magisk > bluspark kernel > f2fs_fstab.zip > f2fs_optimize.zip > factory reset/wipe (from twrp before rebooting), done just reboot into system. You of course lose twrp because magisk doesnt like twrp on oos 10.x for some reason, and will need to set everything up again to cause of the wipe. If you dont factory reset/wipe from twrp before booting into system your system will crash and reboot every time you boot into android, then have to do all the steps I listed again.
EDIT3: Never mind, I was wrong, f2fs makes almost all your apps and storage unusable. Not sure if it's cause of the rom (OOS10.3.0) or because we have to flash stock boot.img and get rid of twrp before booting into system. Either way, f2fs has never really been stable or fun to get working so better to stick to ext4.. that few percent performance boost isnt worth it.
EDIT4: This is my last update. After experimenting with different things, bricking my phone, restoring it via fastboot rom, many many times, I've verified the simplest and cleanest way to install magisk.. Do note you wont be able to keep twrp.
Method A - If you already have twrp
Boot recovery into slot a, flash your rom's stock boot.img, then boot into your recovery in slot b (dont boot into slot a recovery because slot a wont have twrp anymore), flash your rom's stock boot.img, magisk and (optional) your kernel of choice (or not) in that order, then you can boot boot into system. That's it.
Method B - If you don't have twrp
Boot into fastboot, and from your cmd/terminal run fastboot flash boot yourtwrp.img (I suggest Mauronofrio's twrp-3.3.1-16-enchilada-Q-mauronofrio.img or newer). Use your volume buttons to select boot into recovery. Make sure your active slot is B, (if it isnt, install twrp (bluspark and Mauronofrio's twrp both work great) by zip, then follow the steps above in method A). Once you've verified you're in slot B flash your rom's stock boot.img, magisk and (optional) your kernel of choice (or not) in that order, then you can boot into system. That's it.
Maybe @mauronofrio or @eng.stk can verify why magisk or twrp bricks the system when you install them together on OOS 10.
not working
sir i follow your steps but phone is stuck on boot i have official version a10 10.3.0 update on 25.12.19
pls tell me how i get root access....
gauravkapoor99150 said:
sir i follow your steps but phone is stuck on boot i have official version a10 10.3.0 update on 25.12.19
pls tell me how i get root access....
Click to expand...
Click to collapse
U need to flash the magisk v22 zip file through the .108 TWRP recovery
Sent from my ONEPLUS A6003 using Tapatalk
RASTAVIPER said:
U need to flash the magisk v22 zip file through the .108 TWRP recovery
Sent from my ONEPLUS A6003 using Tapatalk
Click to expand...
Click to collapse
sir can you send me a link
lemon07r said:
Maybe @mauronofrio or @eng.stk can verify why magisk or twrp bricks the system when you install them together on OOS 10.
Click to expand...
Click to collapse
@mauronofrio wrote the following in his TWRP thread a while ago:
So little update, after some tests i'm sure there is a compatibility problem between twrp and magisk, i was able to get only one of them, so actually i don't know how to proceed, i need to understand if it is a twrp problem or a magisk problem, TWRP is in stand-by for now.
There are not problems on Android Pie, if you need of the twrp on android Q just flash in boot partition the Q .img (fastboot flash boot twrp.img) and then reboot from fastboot in recovery. Before publishing the twrp I had not tested magisk and twrp together.
On Android 10 use only magisk 19.4
Click to expand...
Click to collapse
xpakage said:
Put the TWRP zip and stock boot img on phone (a TWRP img is not a TWRP zip)
Remove Magisk modules first to avoid issues (in TWRP if you cannot boot to system. https://forum.xda-developers.com/showpost.php?p=72542167&postcount=242)
Update through local update to 10.3.2 is what I prefer to do. Then I do the following.
Reboot to let phone finish whatever. reboot into bootloader.
1. Fastboot TWRP img - fastboot flash boot twrp-3.3.1-18-enchilada-Q-mauronofrio.img - ( https://sourceforge.net/projects/ma...3.3.1-18-enchilada-Q-mauronofrio.img/download )
2. Use volume up to recovery and power button to boot to recovery
3. Flash 10.3.2 stock boot img while in TWRP (or current ROM stock boot img).
4. Flash TWRP zip while in TWRP (https://sourceforge.net/projects/ma...-enchilada-installer-mauronofrio.zip/download ) or Blu zip (https://github.com/engstk/android_device_oneplus_enchilada/releases)
5. Reboot to recovery
6. Flash Magisk 20.3 while in TWRP
(Flash a Q kernel if you want one other than stock)
7. Reboot system
You are now rooted
Stock boot 10.3 img
https://mega.nz/#!PO5x1bYA!dKq3pbxUdpb16zhuqM_idqvWNLnsu4Ky4IAmYQiQUDw
Most stock boot imgs
https://forum.xda-developers.com/oneplus-6/how-to/patched-boot-image-magisk-16-7-beta-t3818853
Click to expand...
Click to collapse
Basically worked for me, too, with 2 exceptions:
- this tool to remove magisk modules etc. wouldn't be flashed, always ended in an unnamed error; probably the cause for some other problems?
- flashing boot.img (V 10.3.4 from this thread) didn't work for me, I always ended up in twrp's splash screen
- got it solved by dirty flashing the full V 10.3.4 ROM (again from the above thread)
Many thanks once again!
Does Pixel 4A have any Temporary Recovery to boot into once and flash the magisk zip file to get magisk root? Android 10 or 11??
thedemon786 said:
Does Pixel 4A have any Temporary Recovery to boot into once and flash the magisk zip file to get magisk root? Android 10 or 11??
Click to expand...
Click to collapse
Why not fastboot the patched boot image instead?
TWRP doesn't work with Android 11.
Push the boot.img to the phone, use Magisk to patch it, download it to the PC and use fastboot to flash it (or boot it and use Magisk to flash).
Everyone hello!
After updating by ota (86->151), magisk app can't detect new patched boot. Of course, have flashed new patched boot in slot B (if flashing in slot A, phone goes to bootloop).
Any suggestions?
Did you make sure to patch the boot from 151 and have you tried not forcing a slot selection?
Something similar happened to me so I just restored my phone using the fastboot return to stock method I downgraded I am on 86 now don't plan on updating. When I did update my phone was acting weird it wasn't as smooth so I downgraded everything's good well except for safety net but I think that's a Google issue for now
If updated using OTA from Asus helpdesk site file - After flashing the file, You gotta make sure to open magisk and flash to inactive slot before the first reboot. If not, it's too late to fastboot patch it. Not sure why though. It's a learning from my Trials and errors.
If updated using RAW - You need to uninstall Magisk before anything. Open the app, Uninstall Magisk, and reboot. Then Flash Raw in fastboot, and then flash the Patched boot image made from the same firmware.
If you flash Raw while on magisk, and then patch with a Magisk patched Boot IMG - it results in bootloop. I dont whats the cause, or how it happens. Recovery for this is to flash Magisk Uninstall zip in TWRP, and then flash Raw, and then fastboot flash with Magisk patched boot image.
Since there is not TWRP for ROG 5 - I can suggest revert back to the working firmware (Previous version) with magisk, boot in, Uninstall Magisk, and then Flash the new Raw file. This method so far worked for me in the latest file.
Cheers!
JazonX said:
If updated using RAW - You need to uninstall Magisk before anything. Open the app, Uninstall Magisk, and reboot. Then Flash Raw in fastboot, and then flash the Patched boot image made from the same firmware.
If you flash Raw while on magisk, and then patch with a Magisk patched Boot IMG - it results in bootloop. I dont whats the cause, or how it happens. Recovery for this is to flash Magisk Uninstall zip in TWRP, and then flash Raw, and then fastboot flash with Magisk patched boot image.
Click to expand...
Click to collapse
It should overwrite the boot, which is the entire Magisk. Never had an issue not uninstalling.