Getting Back to Stock After Some Sort of Mess? - T-Mobile Samsung Galaxy S7 Questions & Answers

Greetings,
After reading a few different tutorials and a hodge-podge of different methods, I think I'm stuck.
I thought I was soft or hard-bricked earlier, but I think I'm in an ok spot now, just unsure how to proceed.
Please read on if you can offer me any suggestion I'd be very much obliged.
I had Galaxy S7 completely stock and working fine until one day last month, randomly turned off, then wouldn't reboot. Would show recovery screen and No Command, and eventually died and wouldn't show charge or anything.
So I bought a new battery. Tried to flash a recovery like TWRP using heimdall, no success. Tried flashing TWRP as AP using Odin 3.1xx, won't even let me (hangs verifying MD5 I'm assuming). How long should I wait for this step?
Eventually wouldn't reboot to recovery or anything other than download mode.. just shows loading recovery.. and reboots (black screen). Doesn't show up in samsung smart switch for emergency (despite showing me this screen several times)...
Deleted heimdall, reinstalled samsung usb drivers, both the download and the ones from within smart switch. Now using Odin to try and flash this most recent stock firmware: SM-G930T_1_20200121102341_gzmpzhj99q_fac obtained using Frija...
Since I couldn't seem to get it to boot to backup, I wanted to at least reset to stock and clear off all my user data. So after many attempts at flashing with Odin, I now get the startup Samsung Galaxy Logo powered by Android flashing, then black screen, nothing. Not sure what to do next. Should I try and boot into recovery and clear caches? Install update via ADB?
What I was able to to do so far, flash BL, CP, CSC while using PIT file from CSC in the PIT tab. Flash settings used: erase nand, re-partition, f. reset. Do not auto reboot.
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1301)..
<ID:0/007> File analysis..
<ID:0/007> Total Binary size: 196 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Erase...
<ID:0/007> ERASE_SECTOR: 0
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> emmc_appsboot.mbn
<ID:0/007> lksecapp.mbn
<ID:0/007> xbl.elf
<ID:0/007> tz.mbn
<ID:0/007> hyp.mbn
<ID:0/007> devcfg.mbn
<ID:0/007> pmic.elf
<ID:0/007> rpm.mbn
<ID:0/007> cmnlib.mbn
<ID:0/007> keymaster.mbn
<ID:0/007> apdp.mbn
<ID:0/007> msadp.mbn
<ID:0/007> cmnlib64.mbn
<ID:0/007> sec.dat
<ID:0/007> NON-HLOS.bin
<ID:0/007> modem.bin
<ID:0/007> Transmission Complete..
<ID:0/007> Now Writing.. Please wait about 2 minutes
<ID:0/007> Receive Response from boot-loader
<ID:0/007> adspso.bin
<ID:0/007> Transmission Complete..
<ID:0/007> Now Writing.. Please wait about 2 minutes
<ID:0/007> Receive Response from boot-loader
<ID:0/007> cache.img.ext4
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/007> Removed!!
<ID:0/007> Added!!
Manual rebooted to ensure able to get into download mode... otherwise previously it would just loop at loading recovery (possibly recovery is corrupt after using heimdall to attempt to flash twrp?).
So far so good.
Flash AP (which contains the recovery.img, correct? With only f. reset and auto-reboot. It successfully flashed the AP and showed pass:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1301)..
<ID:0/007> File analysis..
<ID:0/007> Total Binary size: 4361 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img.ext4
<ID:0/007> persist.img.ext4
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Removed!!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Using Odin modified 3.13.1 by raymond, seemed to have the best luck with it. I can try other versions and give their logs as well.
Not sure what to do now; it took me so many attempts getting to this point, I'm thoroughly confused. Feel like I see the finish line but not sure I ran the race correctly lol. The AP section only took about 2:10 to flash, even though it said everything was successful.
I tried to boot up recovery with vol up, home, power, figured I would delete the caches and then do a normal startup. However it never started recovery from what I can tell. It had the blue text that said loading recovery, then several quick reboots, the powered by android logo flashed a few times, sometimes quickly, then it persisted, now finally just a black screen....
I don't know what I'm doing wrong... should be easy enough according to the guides I've read.
Any help getting back to a working phone is greatly appreciated!

Related

Samsung Galaxy S6 (G920I) problem with firmware

Today I wiped all of my phone data with TWRP recovery and I wanted to install stock 5.1.1. firmware from sammobile but when I do that from odin it almost finishes but it fail at the very end and doesn't want to install it and I am left without phone.
I tried 2 firmware's from sammobile , same fail at the very end.
I restarted the computer, the phone, changed the USB ports, nothing.
This is the text that odin gets me:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> modem.bin
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help me if you can because I can't use my device.
nikola2010m said:
Today I wiped all of my phone data with TWRP recovery and I wanted to install stock 5.1.1. firmware from sammobile but when I do that from odin it almost finishes but it fail at the very end and doesn't want to install it and I am left without phone.
I tried 2 firmware's from sammobile , same fail at the very end.
I restarted the computer, the phone, changed the USB ports, nothing.
This is the text that odin gets me:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> modem.bin
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help me if you can because I can't use my device.
Click to expand...
Click to collapse
I've had that exact same issue, try formatting all data (except recovery) and then try with Odin again, if it fails, try adb pushing a ROM, hope it works like it did with me , also if you didn't wipe your app data and you still want it, make a nandroid so when your on stock firmware, you can extract from nandroid and get back all apps
@SwaggerDaddy you Sir, saved me!
I installed TWRP recovery and wiped again everything, installed via odin again the firmware and failed again, ok but after that I installed the TWRP recovery, the phone works perfect with the stock 5.1.1.
Thank you Sir for helping me, the amazing community of XDA Developers, thank you all I don't know what I would do without you guys!

False writing firmware!!!!crazy problem on GT-P5110. Aanyone does have any solution

Hi Guys, i have big problem with my gt-p5110 and i need your help, becouse i not undestend why it doesn't work.
So in my Tab2 it is installed cm 10.1.3 with kernek 3.0.31, and it work well until two days ago...after when it star in main page after 20 /25 second it rebot , again again agai...so I said no problem, i flash a new rom.....and here start the problems..
In recovery mode cm 6.0.1 if a try to istall new zip file from sd, it work and after teh installation i see on the recovery screan succefull!!! same if i install new rom from zip file from sd.....and although I do various wipe, when i star system, the pad star with old cm firware , and notthing change, 20/25 seecond anche the pad reboot again....
It tried to instal factory rom with odin, and this is the result:
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P5110_JB_SBL.tar.md5 is valid.
<OSM> P5110XXDNH2_P5110OXADNH2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> Sbl.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> system.img
<ID:0/007> boot.img
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> recovery.img
<ID:0/007> Sbl.bin
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/007> Removed!!
so i think that all ok....but after teh restar again old cm rom installed...i dont undestend why??? if i instal new rom, and odin tell me that it is correct install on tab2, why the system star again with old system???
I need help
Thanks all people that help me.
Luck

Softbricked S6 after trying to unroot

Hi so yesterday I softbricked my phone. I was trying to unroot by flashing a stock rom. I flashed 6.0.1 using odin 3.10.6. and before I was on a stock 5.1.1 rom. This is what happened after flashing.
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1101)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> cache.img
<ID:0/007> hidden.img
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/007> Added!!
When I try restart my phone, it says "an error has occurred while updating the device software. Use the emergency recovery function in the Smart Switch PC software." Have also tried flashing using odin 3.11.1 but same issue. So basically I am stuck in download mode. Any help on what to do next would be greatly appreciated.
Try a different odin version, usb port and unzip the rom and make a manual flash of bootloader, pda, modem...

sm-j415f software bricked!keep restarting only

sm-j415f keep restarting.cannot enter recovery.download mode ok.i tried to flash below firmware.i use odin 3.14.1 but not fixed.
1.J415FXXU5BSL1
2.J415FXXU6BTB3
3.COMBINATION_FAC_FA81_J415FXXU4ASG2_FACFAC_CL14376089_QB24592148_REV00_user_mid_noship_MULTI_CERT.tar.md5
4.COMBINATION_FAC_FA81_J415FXXU5ASK1_FACFAC_CL14376089_QB27234897_REV00_user_mid_noship_MULTI_CERT.tar
after i flash abow all firmwares, i saw this common error message in phone screen and odin.
Phone screen say- (Secure check fail:sbl1 )
Odin say -
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1401)..
<ID:0/007> File analysis..
<ID:0/007> Total Binary size: 1881 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
.
geeth rb said:
sm-j415f keep restarting.cannot enter recovery.download mode ok.i tried to flash below firmware.i use odin 3.14.1 but not fixed.
1.J415FXXU5BSL1
2.J415FXXU6BTB3
3.COMBINATION_FAC_FA81_J415FXXU4ASG2_FACFAC_CL14376089_QB24592148_REV00_user_mid_noship_MULTI_CERT.tar.md5
4.COMBINATION_FAC_FA81_J415FXXU5ASK1_FACFAC_CL14376089_QB27234897_REV00_user_mid_noship_MULTI_CERT.tar
after i flash abow all firmwares, i saw this common error message in phone screen and odin.
Phone screen say- (Secure check fail:sbl1 )
Odin say -
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1401)..
<ID:0/007> File analysis..
<ID:0/007> Total Binary size: 1881 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
.
Click to expand...
Click to collapse
Use odin 3.13.1, the one your using is for android 10 and above.
respectablenoob said:
Use odin 3.13.1, the one your using is for android 10 and above.
Click to expand...
Click to collapse
i used odin 3.13.1.but fail.same result showing odin and phone screen
Make sure your csc and cp is exactly the same model as your phone for your region. Search your firmware+ your region. And if everything doesnt work, dont put the other files, just the AP file.
---------- Post added at 05:52 PM ---------- Previous post was at 05:51 PM ----------
geeth rb said:
i used odin 3.13.1.but fail.same result showing odin and phone screen
Click to expand...
Click to collapse
Make sure your csc and cp is exactly the same model as your phone for your region. Search your firmware+ your region. And if everything doesnt work, dont put the other files, just the AP file.
samsung sm-j415f security error/// pls can i get solutions for this?

Need assistance please on combination flash, PIT, etoken - Note 10 (SM-N970U)

Good day to all,
I've been trying to flash into Combination with no success at all. Tried several methods to no avail. Can some OG's please help me.
Phone model : Samsung note 10 (SM-N970U)
i had all the required combination flash file and the PIT file as well. When i try to flash it shows :
SW REV CHECK FAIL : [abl]Fused 5 > Binary 1 (on my phone)
Odin Log :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1301)..
<ID:0/007> File analysis..
<ID:0/007> Total Binary size: 3963 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> abl.elf
<ID:0/007> xbl.elf
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Darklord888 said:
Good day to all,
I've been trying to flash into Combination with no success at all. Tried several methods to no avail. Can some OG's please help me.
Phone model : Samsung note 10 (SM-N970U)
i had all the required combination flash file and the PIT file as well. When i try to flash it shows :
SW REV CHECK FAIL : [abl]Fused 5 > Binary 1 (on my phone)
Odin Log :
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1301)..
<ID:0/007> File analysis..
<ID:0/007> Total Binary size: 3963 M
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> NAND Write Start!!
<ID:0/007> SingleDownload.
<ID:0/007> abl.elf
<ID:0/007> xbl.elf
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
AFAIK the SM-N970U has a locked bootloader. That prevents flashing another firmware files.
If you want to flash other firmware files, you either need to get the bootloader unlocked (what is not that easy so some devices and not available at all for others), or better get an unlocked device.

Categories

Resources