I just noticed yesterday that my screen started cutting out for long periods of time.
This morning I verified the phone is on when the audio, haptic feedback, and screen are only working 1-2% of the time.
This only happens when I have WiFi turned on. I was able to get the device to work when I left any wifi area.
Then I als o shut off screen timeout and lock screen so that when the device is on wifi, it is easier to get in and shut off the wifi again.
Anyone know what this could be?
Related
WM6. Whenever I turn the screen off, Wifi automatically turns off until the screen is turned back on.
Can I change this setting? and yes, I know it will drain the battery, but I have 2 spares that are constantly on charge.
Thanks
[APP] WifiNoStandby - stop wifi going to sleep
Something new - under Wifi Settings/Advanced - I have Wi-Fi set to sleep when display is off..
This doesn't seem to be the case. My WiFi is Always on.
I would imagine that the icon would disappear like it does when WiFi is turned off.. but when the phone is asleep and then wakes up, the WiFi connection is still there.
Anything I can try to fix this? I have tried changing the WiFi sleep policy to the other 2, then changing it back to display power - didn't work.
I did have to reboot the phone last night because I couldn't get WiFi to turn off, but I don't have a problem today with turning it on or off.. just won't go to "sleep"
It may be turning off and you just don't notice it. Cause I know that as soon as I turn on the display again its maybe half a second and then the wifi is back on. So you may be missing the switch.
I also notice that I have to leave the display off for a good two or three mins for it to turn off.
Sent from my SAMSUNG-SGH-I897 using XDA App
Is there a way to find out how long you are connected to an Access Point?
I am noticing a big difference in battery drain when WiFi is turned completely off, then when it is in the "Sleep" mode.
I have a sprint Nexus S 4g. It recently got wet and i let it dry out for a day. The screen is slightly cracked, but before getting wet, the screen still worked properly. Currently, my phone will turn on and i can confirm this through the use of droidscreen, which displays the screen. Using adb, i can still input taps but the screen remains black. Even though the screen is black, the screen still registers touches and i can still open apps, open the notification bar, etc. I let the battery die recently. When i started charging again, it displayed the charging animation when off. I turned it on, and it did not show the boot animation, but the screen turned on at the home screen (since i do not use a lockscreen, and i mostly use this device for a hotspot). The power was at 1%, so i let it charge. When i came back to it a few minutes later, the screen no longer worked again. I have been able to recreate this and i do not know why the screen only displays at around 1%, but still registers touch at any time. Could replacing the screen fix this issue or is this a result of water damage in the circuitry?
This device is rooted and is currently on CM.
When I start my Moto G2 (XT1038) from cold, the entire boot animation plays and the home screen shows and the phone works fine. The moment the phone is locked and I press the power button to turn the screen on and entire my pin, the area near the microphone heats up rapidly to a point where I can not touch the spot for more than a few seconds. The screen stays blank though. After a few minutes of inactivity the area cools down. But if I try to turn the screen on the same thing happens. Meanwhile, I can hear the alarms I have set in my phone, go off at designated times, can hear the incoming phone call rings, SMS / message notifications, etc. But cannot get the screen to come on after the initial bootup. Can not turn off the phone either, same thing happens. Battery lasts as usual. No heating issues while charging. Any ideas why this might be happening? It is running Marshmellow at the moment, and the update happened many weeks before this issue. Auto-updates are turned off.
Not sure if I need to replace the display or battery or some other hardware.
Recently, my Fit2 Pro has started keeping the screen on while I'm out running. It used to turn off after the timeout (15 seconds) but now I have to turn the screen off manually, and then it'll turn on again and stay on. Maddening.
I've had to get around this by turning DND on or by turning off the wake gesture. Anyone else getting this problem or is my unit faulty?