Hello, i have seemed to have bricked my phone in a way I can't recover from. I can reach the Fastboot on my phone, but I can't do anything after that. Trying to boot to TWRP to the phone with fastboot will send it to a black screen with a solid white light. Attempting to enter the stock recovery on the phone also goes to the same black screen with a white light.
I have tried using the flashing tool in https://forum.xda-developers.com/t/rom-stock-fastboot-op6-stock-fastboot-roms-for-oneplus-6.3796665/, but I'm not sure if i got the right file set, as I only remembered that I had Oxygen 9 on my phone.
Lastly, I have tried to use the MSMdownloadtool to fix the issue. I have tried multiple versions from multiple sites, but the progress always gets stuck at 'param preprocessing' while the phone sits at a black screen with a green solid light
Any help on this will be nice. I am using a OnePlus 6 A6003. I would also like to add that while in the fastboot mode, the Bootloader version and the Baseband versions are blank
Just wanted to state I have got the issue fixed. I found the website https://onepluscommunityserver.com/ that had a version of MSM that worked for me.
Related
I have looked at multiple guides on this and other sites, googled and tried stuff and I cannot resolve this problem. Hopefully I am posting in the right place.
I took the jump and unlocked the bootloader on my Moto G first generation, XT1034 successfully. I flashed TWRP 2.8.60.xt1034.zip with adb and this was successful. Then I flashed Super SU 4.6 Update and that was successful. I got into trouble I guess when I tried to flash Cyanogenmod 12.1 nightly. I used TWRP to flash via install. The flash had an error, which unfortunately I didn't write down. I believe it was something to do with a partition. However, it looked like the flash failed. At this point and for hours I have been trying to fix the "Warning Bootloader Unlocked Loop I am stuck in.
I have been able to get into the phone and flash via adb commands. I've tried several commands suggest to fix this that I have found in forums. I have tried flashing several recoveries including an older TWRP per the method in this thread, a clockworkmod - and the original 2.8.6.0.xt1034. When I get into the phone bootloader which is available, I have not been able to access any options in recovery. Pushing the power button on recovery leads to a blank screen sometimes followed by a recovery starting or a Motorola Logo starting up and a couple times a recovery. TWRP has started a couple times, but never gets past the intro screen, where it locks up. clockworkmod (clockworkmod-6.0.4.7-falcon.img started once after flashing through adb and gave me flash options. I tried to sideload, didn't understand, went back and the recovery locked up. These recoveries no longer load at all.
Through all of this the "Warning Bootloader Unlocked" logo screen comes up after plugging into the computer (Windows 8.1).
Example, I open the phone bootloader by waiting for the phone screen to go from the "Warning Bootloader Unlocked" screen to blank - it cycles from logo to blank. If I'm quick the phone and hard boot the phone will boot into bootloader. I connect to the laptop through USB. When I toggle to recovery and hit the power button the screen goes blank, the Motorola Logo pops up, goes blank and then the "Warning Bootloader Unlocked" appears. The Laptop then seems to connect and disconnect as the Warning screen comes on and turns off.
The factory selection just goes to a blank screen.
I would really appreciate some advice on how to get the phone back to a state in which I can work with it and try again. It is very difficult wading through all of the information out there. I've learned a lot through this issue, but can't take it any further.
Thanks, Jeff
Solved - Stuck in "Warning Bootloader Is Unlocked" Loop
This resolution took many hours to figure out, but I finally got there with this guide - http://forum.xda-developers.com/showthread.php?t=2542219, this thread - http://forum.xda-developers.com/showthread.php?p=54855457#post54855457 and this thread - http://forum.xda-developers.com/gen...e-firmware-t3042687/post59139823#post59139823.
I tried RSD Lite on different computers and USB cables I could not get the device recognized. So I ended up with the MfastbootV2 method to reload stock firmware, which I found on the firmware thread above - this was big, as my phone is with Wind Mobile in Canada and the link is the right one. The only thing I picked up from a different website was to use a computer with USB 2 ports. This is what I did, but I don't know one way or the other if USB 2 was needed. .
Can't thank you hard working guys enough for the time you take to put these threads together. I'm back up and running. As a bonus, after a big clean up in the process, my phone is running fast again.
Thanks everyone.
Hey guys, I've got a Kyocera Brigadier and I decided to change the runtime from Dalvik to ART. Now the phone is stuck on loadscreen and I don't know how to fix it. The phone is rooted using the KingRoot app, but I don't know if that would help in any way.
Please help me guys!
Similar Issue
I am have a very similar issue, I also rooted my Brigadier with Kingroot and all went well. However, I attempted to flash the Xposed Framework onto it using Flashify. After doing such it got stuck in a bootloop, I was able to fix that problem by booting into fastboot mode and using fastboot to push stock firmware back onto my device. However now I have an even bigger problem where my phone boots up to the Powered by Android screen and then to the Kyocera screen, however instead of continuing to boot to the Verizon Wireless screen and then into the phone, it gets stuck at a black screen. I have tried waiting for hours and nothing at all happens, also I can no longer seem to boot into fastboot mode or in other words the Powered by Android screen with the little 1 in the top left corner of the screen. Fastboot nor ADB recognizes the device when plugged into my computer, as neither list anything when ran. Please help, I don't want to have to pay and end up sending my phone into Verizon to be unbricked.
Ornias Abezethibou said:
I am have a very similar issue, I also rooted my Brigadier with Kingroot and all went well. However, I attempted to flash the Xposed Framework onto it using Flashify. After doing such it got stuck in a bootloop, I was able to fix that problem by booting into fastboot mode and using fastboot to push stock firmware back onto my device. However now I have an even bigger problem where my phone boots up to the Powered by Android screen and then to the Kyocera screen, however instead of continuing to boot to the Verizon Wireless screen and then into the phone, it gets stuck at a black screen. I have tried waiting for hours and nothing at all happens, also I can no longer seem to boot into fastboot mode or in other words the Powered by Android screen with the little 1 in the top left corner of the screen. Fastboot nor ADB recognizes the device when plugged into my computer, as neither list anything when ran. Please help, I don't want to have to pay and end up sending my phone into Verizon to be unbricked.
Click to expand...
Click to collapse
I have the same problem. I bought a new a Brigadier that was on 4.4.2. I rooted with Kingroot ran update and now my phone will not boot past Kyocera screen. It goes black with the back light on. Did factory wipe and still nothing. I am shocked that KK has killed yet another phone of mine. I very much dislike KK ROM. What did you find out?
Hi all, have a rooted OPO that was running ExodusOS. I decided to try a flash of Lineage and so booted into recovery, backed everything up, flashed it. Everything seemed to go okay but after the boot logo the screen just goes black and stays that way until it gets shut back off. I went back to TWRP, loaded my backup and all seemed well as I was still able to use my old backup just as normal. Well, I tried reflashing Lineage from TWRP again and I still get the same black screen issue. This time, however, the phone will neither boot into Fastboot nor into recovery mode and just goes straight into loading Lineage. Because of this I am left with a soft brick until I can get this straightened out. I tried connecting the phone to my PC but it is not detected as a device. I only need to boot into my backup one more time so that I can back everything up, so even if it's only a temporary fix, I'm okay with that too. Any suggestions?
AMpageg2 said:
Hi all, have a rooted OPO that was running ExodusOS. I decided to try a flash of Lineage and so booted into recovery, backed everything up, flashed it. Everything seemed to go okay but after the boot logo the screen just goes black and stays that way until it gets shut back off. I went back to TWRP, loaded my backup and all seemed well as I was still able to use my old backup just as normal. Well, I tried reflashing Lineage from TWRP again and I still get the same black screen issue. This time, however, the phone will neither boot into Fastboot nor into recovery mode and just goes straight into loading Lineage. Because of this I am left with a soft brick until I can get this straightened out. I tried connecting the phone to my PC but it is not detected as a device. I only need to boot into my backup one more time so that I can back everything up, so even if it's only a temporary fix, I'm okay with that too. Any suggestions?
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
Sounds like a Hardware issue? Sorry to say what your saying doesn't add up and or make sense. Fastboot should work no matter what even if you soft brick it and mess up recovery. I suggest letting the power fully drain maybe and google how to fast boot in case you are doing it wrong.
Mr.Ak said:
https://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
Click to expand...
Click to collapse
I've tried that but it can't find the phone. The phone gets detected as a new device in windows as evident from the device connection sound but it also never shows up in the list of devices from My Computer.
AMpageg2 said:
I've tried that but it can't find the phone. The phone gets detected as a new device in windows as evident from the device connection sound but it also never shows up in the list of devices from My Computer.
Click to expand...
Click to collapse
I agree with what @Shinobi_warrior said.Seems like you just have a soft brick,so you should be able to boot into fastboot mode without any issues.Are you sure you're doing it the right way? Did you try draining battery completely and then booting into fastboot(yes,you don't need much battery to boot into fastboot mode)?
Well I was finally able to get the device detected by ADB, but it just shows as offline. I attempted to use the repair kit and nothing seemed to happen. I also attempted a different tool (https://forum.xda-developers.com/on.../oneplus-one-toolkit-manudroid19-gui-t2807418) and then booting into either fastboot or recovery that way, a terminal window pops up and quickly disappears, and then nothing else happens. I still see the TugaPower boot logo and it still goes to the blank black screen after this.
Greetings everyone,
I decided to post my problem with my phone after searching the entire internet for similar problem but with no luck. Anyway I used to play around with my Samsung j7 pro for 2 years, I managed to flash twrp and thus many other custom roms, until last week when I recklessly flashed a sboot.img.tar file through Odin in order to fix cellular network in a rom I flashed earlier, this alone bricked my phone refusing to get past the Samsung logo, so like I do always, I tried to restore my phone by flashing the stock firmware (9.0) which I always keep on my PC, but surprise, the phone refuses to go through the process and gives me this error:
sw rev check fail bootloader device -1 binary 6
(same with 8.0 and 7.0 firmware)
I searched the internet for same error but with no luck, because I understand it's a mismatch between device bootloader current version and the firmware bootloader's, that they should be the same or higher, meaning you can't downgrade, I get that! but I never seen device with negative figure (-1) what that's supposed to mean? my device bootloader used to be on 6, how did it managed to jump to minus one ?
then I tried to flash TWRP to see if I could flash a rom and get around it, so I did, but when booting into recovery the screen goes black, I thought first the phone turned off, but not really, because TWRP seems to work with screen completely black, I knew that because I accidentally touch the screen and I sense vibration, I managed to reboot the phone via twrp just by guessing the buttons location (screen always black) in order to prove that TWRP is working with screen off. I tried to flash multiple TWRP versions but the same problem, no screen just touch, by the way there is nothing wrong with display hardware because it shows Samsung logo at start and also can boot into download mode just fine.
I hope someone could help me overcome this big of an issue, because I tried everything.
Hi, i unclocked the bootloader and flashed updated to Android 11 on my A51 few weeks ago and everything was going fine until yesterday i plugged it into charger and after a few minutes when i tried to unlock the phone, the screen doesn't show up. eveything's black. i tried forced restart method and other possible methods but none worked. the display only shows samsung logo while restarting and while in recovery and download mode but once it restrats completely, turns black again. i thought relocking the bootloader will do the job so i go to download mode and select LOCK BOOTLOADER( i didn't know if it was correct as i have 0 knowledge regarding these). and then it's stuck in download mode and no methods worked to get outta it.after a few hours, several while vertical lines and then blue dots(in the corner and surrounding the fingerprint sensor) start appearing on the screen and increases gradually with a break. however, i was able to install the custom firmwire (android 10) {although samsung officially released android 11 on A51s} using odin and then wipe the phone completely but now it restarts and then back again on the black screen. what can i do now? thank you