Database Info

[Q] Stuck in recovery some time after flashing cwm

Actually it might be a little more complicated...
Full story: I was trying to flash cyanogenmod so I unlocked the bootloader and flashed cwm and SuperSU. Until this point everything worked just fine. I copied the CM-zip to the root of my phone. When trying to install CM however I got an error saying "Some changes failed" (Status 7), basically this. Also I started having trouble booting the system normally. The phone would either get stuck at the bootloader unlocked screen or just boot into recovery. I had done a backup at some point (not prior to starting to try to flash CM, I didn't really think I'd need one since the phone was brand new and I didn't there was any data on it I'd miss... yeah, well...) and sometimes restoring it would enable me to boot normally. However, after the factory reset before my nth attempt to install CM, that was gone as well. After doing a bit of research I found this thread. Since I had version 6.0.13 of cwm as well, I flashed twrp v2.7.1.2 instead. The interface is a little friendlier, but other than that there have been no changes.
Now I can't boot the system normally, not even by selecting "System" when rebooting it from recovery, it will just keep booting into recovery. I can still fastboot, though. My CM-zip is gone since that infamous factory reset and I can't get it back on the phone, or anything else for that matter, since my pc only detects the phone when it's booted normally. I tried pushing CM with adb but when I try to mount any partition I get an error saying E: Unable to find storage partition to mount to USB.
Any ideas how I could fix this mess? Or suggestions on how to avoid ****ing it up any further...

If you can adb, you can adb push... You are just adb push'ing to the wrong place I suppose.
Code:
adb push blah.zip /sdcard/
Should work...
Or even better, just sideload (put phone in recovery & 'sideload mode' before running):
Code:
adb sideload blah.zip
Either way, CWM for our device is ancient and does not support the latest ROM's. The version of TWRP should work fine, as should the latest OpenRecovery (2.09 IIRC).

Sideload worked perfectly! Thank you so much!

cm11 working only TWRP here , with cwm appears same error

mmichaelalves said:
cm11 working only TWRP here , with cwm appears same error
Click to expand...
Click to collapse
Did you not read my post?
arrrghhh said:
Either way, CWM for our device is ancient and does not support the latest ROM's. The version of TWRP should work fine, as should the latest OpenRecovery (2.09 IIRC).
Click to expand...
Click to collapse

Any root for SM-J327W yet?

Hello, I was searching for a root for my "new" Samsung J3 Prime (SM-J327W) that I got from my sister. I did the OEM Unlock and in ODIN Mode, it says that it's also "FRP LOCK : OFF". So far, CF-Auto-Root didn't work and all TWRP images, that I found, wouldn't even download on the device . I tried images for the "T", "P" and "U" variants also. The "P" one, lead to bootloop (I recovered stock rom since I got it). So is there any root for this device? It's on the latest versions of firmware and Android available for it.

Did you find anything for the J327W yet? I can only find ROMs for the 320, 327P and 330. I've been having very erratic battery life for over a year. It started after a factory android update. Sometimes my battery life will drop from 70% down to less than 5% in a minute. I've done a factory reset, cleared the cache and replaced the battery but nothing has helped. Trying to put a new ROM OS on this POS is my last hope.

shane_c said:
Did you find anything for the J327W yet? I can only find ROMs for the 320, 327P and 330. I've been having very erratic battery life for over a year. It started after a factory android update. Sometimes my battery life will drop from 70% down to less than 5% in a minute. I've done a factory reset, cleared the cache and replaced the battery but nothing has helped. Trying to put a new ROM OS on this POS is my last hope.
Click to expand...
Click to collapse
I think you'll need a battery replacement at this point... I did build a TWRP ROM myself for my popeltecan (code name of J327W in Canada apparently) but, according to a TWRP Builder Developer, my device might have some kernel issues with TWRP so I can share my ROM but I am not sure it will work on your device. Do you have your stock ROM in case?

Here is a GDrive link to my recoveries, there's the stock and the twrp one but be aware that you need all the ROM if there is a problem with the twrp (that means stock : BL, AP, CP and CSC). But you can use the stock recovery to build a device tree.
https://drive.google.com/open?id=1dNZGaNvCtd5kinHNfnr8MV5Z6o2_GOj4

MikasuX14 said:
I think you'll need a battery replacement at this point... I did build a TWRP ROM myself for my popeltecan (code name of J327W in Canada apparently) but, according to a TWRP Builder Developer, my device might have some kernel issues with TWRP so I can share my ROM but I am not sure it will work on your device. Do you have your stock ROM in case?
Click to expand...
Click to collapse
Replaced the battery about 3 months ago but it made no difference. I have some vacation time coming up so will have a little more free time to look into things.

shane_c said:
Replaced the battery about 3 months ago but it made no difference. I have some vacation time coming up so will have a little more free time to look into things.
Click to expand...
Click to collapse
Maybe a factory reset would be a good idea to try. If you want to try my twrp recovery build, you'll be wiping your data anyway. I highly suggest you to get the full stock rom since even just getting back the stock recovery could end up with a weird sort of corruption (like duplicated or unknown options inside the Settings app, or at least I experienced that). I am not responsible if it breaks anything, you were warned to get your precautions such as getting the stock rom.

MikasuX14 said:
Hello, I was searching for a root for my "new" Samsung J3 Prime (SM-J327W) that I got from my sister. I did the OEM Unlock and in ODIN Mode, it says that it's also "FRP LOCK : OFF". So far, CF-Auto-Root didn't work and all TWRP images, that I found, wouldn't even download on the device . I tried images for the "T", "P" and "U" variants also. The "P" one, lead to bootloop (I recovered stock rom since I got it). So is there any root for this device? It's on the latest versions of firmware and Android available for it.
Click to expand...
Click to collapse
hi if your still looking. i looked into it and the j327u twrp does work on j327w. i had the same problem trying to gain SU access with the other image files for j327w i had to use magisk zip and install it from twrp menu. had to format data and mount system in twrp.

twrp j327u does work but i could not get supersu or magisk to work, my build is J327WVLS4BSK1 with 8.1.0 oreo. i'm not sure there's a way to get past dm-verity using the boot patch by asphyx in the TWRP threads or the universal dm-verity workaround by zackptg5.
i first flashed twrp j327u using odin, ran up against dm-verity when running supersu. both MikasuX14 and another twrp j327w version i found would also flash and load, but the touchscreen wouldn't register my input. cfar didn't work either
sfirmware (website) has workable firmware for rev 4 j327w builds in case you need to recover your phone from soft brick - i could get my build's firmware to flash using the patched odin 13.3.3 version found on this site

bytwigorlimerick said:
twrp j327u does work but i could not get supersu or magisk to work, my build is J327WVLS4BSK1 with 8.1.0 oreo. i'm not sure there's a way to get past dm-verity using the boot patch by asphyx in the TWRP threads or the universal dm-verity workaround by zackptg5.
i first flashed twrp j327u using odin, ran up against dm-verity when running supersu. both MikasuX14 and another twrp j327w version i found would also flash and load, but the touchscreen wouldn't register my input. cfar didn't work either
sfirmware (website) has workable firmware for rev 4 j327w builds in case you need to recover your phone from soft brick - i could get my build's firmware to flash using the patched odin 13.3.3 version found on this site
Click to expand...
Click to collapse
heres what i did. i soft bricked, bootlooped and had to flash firmware from sfirmware a few times to get it to work
i used a twrp for j327u i found on a another similar thread on this topic. i flashed it with odin.
once inside twrp menu i went to wipe menu, i hit format, then back to mount menu, checked boxes data/system (previously data or system wouldnt check off before formatting data).once data and system were mounted i then
plugged phone back into computer while in twrp menu. the phone showed up as J327u cut/paste the latest magisk .exe into the internal storage of j327u (on computer) . i then on twrp menu found and installed magisk exe finally got it to properly install magisk i then in reboot menu hit system and reboot.
the phone restarted after awhile like it was factory reset but once i set up the phone magisk apk was already installed and root access was available. hope this helps.

so i've been busy for a long while before looking back into this. I will try again with the J327U rom. Right now, i struggle to find stock roms of the J327W because i flashed a not working twrp apparently and it locks my boot.

The J327U TWRP didn't work for me. Though, twrp itself works but i cannot get the system to boot and i cannot get to root it, no matter what i tried, i ended up in boot loop.

I managed to root this phone without TWRP. I used Linux tools to do this so I'm not sure if it could work on Windows.
Requirements:
Stock ROM for your phone (I used samfirm.js to pull it from the Samsung servers but downloading from sammobile.com works too)
A way to extract zip files
A way to extract tar files
Heimdall flasher (https://www.glassechidna.com.au/heimdall/)
Magisk Manager APK
An Internet connection on your phone
A compatible USB connector for your phone
Of course, a SM-J327W running the stock Android firmware
Obligatory warning: This WILL void the warranty of your phone and permanently trigger the warranty void flag. It also WILL cause a factory reset, so back up all your data first.
Bear with me, because there are a lot of steps. This will take around 15 to 30 minutes.
You will need to download and extract a stock ROM for your phone. Make sure that you download a ROM for the SM-J327W and not another model. Also make sure to download the latest version available.
Stock ROMs usually come in a zip file containing a few tar.md5 files. You will only need to extract the one that starts with "AP" for this procedure.
Step 1: Extract the tar.md5 file that starts with "AP" from your stock rom.
Step 2: Open the tar.md5 file in an archive manager. You may need to remove ".md5" from the end of the file.
Step 3: Extract the boot image (boot.img) from the AP file.
Step 4: Upload the boot image and the Magisk Manager APK to your phone. You can use ADB to transfer the files. For example:
adb push boot.img /storage/emulated/0
adb push Magisk-v22.0.apk /storage/emulated/0
Step 5: Open the files app on your phone. Navigate to the internal storage and tap on the Magisk APK file to install it. You may be prompted to allow installation from unknown sources.
Step 6: Open the Magisk app. It should say that Magisk isn't installed and it shoulld say "Yes" beside "Ramdisk". Tap the cogwheel icon in the top-right corner.
Step 7: Due to a bug in Magisk, you need to install version 21 instead of the latest version (v22). Set the update channel to "Custom Channel".
Step 8: When prompted, enter the following URL: "https://raw.githubusercontent.com/t...d863d3a15c6a2276b1061a280ece80ed7/stable.json" (Without the quotes.)
Step 9: Now it's time to patch the boot.img file. Tap the button to install Magisk and select the option to patch a file. When prompted, navigate to the internal storage and select the boot.img file that you transferred previously.
Step 10: Magisk will patch the file and tell you where it saved the patched file. Transfer the patched file to your computer. You can use ADB for this, for example:
adb pull /storage/emulated/0/Download/magisk_patched_XXXXX.img
Remember to replace the Xs with the the random characters that Magisk added to the file name.
Step 11: Reboot your phone into Download mode. You can shut it down and then hold the power, home, and volume down buttons at the same time to enter Download mode or use ADB: "adb reboot bootloader"
Step 12: A warning may show about the dangers of installing a custom OS. Press the volume up key to continue.
Step 13: The screen should now show "Downloading... Do not turn off target." If your phone isn't already plugged into your computer, plug it in now.
Step 14: Use Heimdall flasher to flash the patched boot image. For example:
heimdall flash --BOOT magisk_patched_XXXXX.img
Again, replace the Xs with the random characters that Magisk added to the file name.
Step 15: After a few seconds, Heimdall should report that the flash succeeded and your phone will reboot. It may take longer than usual. Leave it to do its thing and DO NOT pull out the battery.
Step 16: Your phone will show a notice that unauthorized changes have been detected and will prompt you to factory reset it. Press the button to perform the factory reset.
Step 17: Set up your phone as if it was new. It's not rooted yet, but you're really close if you got so far.
Step 18: Once you reach the home screen, upload the Magisk Manager APK to your phone again and install it like before.
Step 19: Open Magisk Manager. It will show that Magisk is installed and may prompt you to reboot to complete installation. Do not update Magisk to v22 or you will lose root access and you will have to flash the patched image again.
In the (very unlikely) case that your phone doesn't boot after flashing the patched boot.img, you can simply flash the original boot image and it should be fixed.
CONGRATULATIONS! You just rooted your SM-J327W successfully.
I also managed to port TWRP to this phone with the touchscreen working using the kernel from a recovery image for the SM-J327P found here: https://forum.xda-developers.com/t/...-1-samsung-galaxy-j3-emerge-sm-j327p.3573607/. All the partitions are mapped correctly. Due to a bug (presumably with the kernel), the data partition can unfortunately only be mounted read-only. However, this shouldn't affect being able to flash zips on your phone and you can insert an SD card to write backups onto. In the future, I may port CWM recovery to this phone using the stock kernel to be able to mount the data partition read-write.
You can find my custom recovery attached to this reply.

Follow up: It seems that the bug that causes Magisk to fail is fixed in the latest version (v22.1.) As a result, steps 6-8 in my previous post are unnecessary.

MikasuX14 said:
Here is a GDrive link to my recoveries, there's the stock and the twrp one but be aware that you need all the ROM if there is a problem with the twrp (that means stock : BL, AP, CP and CSC). But you can use the stock recovery to build a device tree.
https://drive.google.com/open?id=1dNZGaNvCtd5kinHNfnr8MV5Z6o2_GOj4
Click to expand...
Click to collapse
link is dead do you have twrp for j327w?

[HELP] Remove boot loop without root & USB debugging?

Hi,
this is my first post on this forum, so please let me know if you are missing any information …
My problem: I'm experiencing a boot loop with my Nexus 5 after having changed its damaged battery. I didn't use it for a long time because of this damage. Now, it does start the boot sequence again, but only to the "circle" animation which it keeps showing indefinitely.
The circumstances:
I never tried to root the phone
USB debugging is not (and cannot be) enabled
I'm completely sure the problem is not caused by the power button (seems to be a common cause)
stock recovery is reachable
an old version of ClockWorkMod Recovery (from this thread) is bootable
three tested versions of TWRP won't boot
What I tried:
I unlocked the bootloader. With both the stock recovery and CWM, I tried to
wipe the device / the cache partition
flash a stock image (directly downloaded from the Google developer page)
flash a ResurrectionRemix image
None of these worked. It seems that the recovery systems are not able to write on or even to mount the necessary partitions. As the stock recovery apparently needs access to /cache for adb sideload, any attempt to flash anything results in an error message. CWM is able to sideload the zip file, but writing the image fails.
I furthermore tried the "factory" (not OTA) image from Google with its flash-all.sh script which tries to also update boot loader and other things via fastboot – every single one of these update attempts failed as well.
So, my question is: Does anyone of you know of a way to get my phone working again?
Many thanks in advance, best regards
Hørk

Hørk said:
Hi,
this is my first post on this forum, so please let me know if you are missing any information …
My problem: I'm experiencing a boot loop with my Nexus 5 after having changed its damaged battery. I didn't use it for a long time because of this damage. Now, it does start the boot sequence again, but only to the "circle" animation which it keeps showing indefinitely.
The circumstances:
I never tried to root the phone
USB debugging is not (and cannot be) enabled
I'm completely sure the problem is not caused by the power button (seems to be a common cause)
stock recovery is reachable
an old version of ClockWorkMod Recovery (from this thread) is bootable
three tested versions of TWRP won't boot
What I tried:
I unlocked the bootloader. With both the stock recovery and CWM, I tried to
wipe the device / the cache partition
flash a stock image (directly downloaded from the Google developer page)
flash a ResurrectionRemix image
None of these worked. It seems that the recovery systems are not able to write on or even to mount the necessary partitions. As the stock recovery apparently needs access to /cache for adb sideload, any attempt to flash anything results in an error message. CWM is able to sideload the zip file, but writing the image fails.
I furthermore tried the "factory" (not OTA) image from Google with its flash-all.sh script which tries to also update boot loader and other things via fastboot – every single one of these update attempts failed as well.
So, my question is: Does anyone of you know of a way to get my phone working again?
Many thanks in advance, best regards
Hørk
Click to expand...
Click to collapse
Ever fix it?

Stuck in a bootloop, please help

Hey,
Quick rundown: Stuck in a bootloop to some sort of empty bootloader screen which has the readout:
"Start/Restart Bootloader/Recovery Mode/Power Off"
"Press volume key to select, and press power key to select"[Regarding above options]
"FastBoot Mode
PRODUCT_NAME - sdm845
VARIANT - SDM UFS
BOOTLOADER VERSION -
BASEBAND VERSION -
SERIAL NUMBER - [Gonna leave this out for now]
SECURE BOOT - yes
DEVICE STATE - unlocked" [this line is in red]​
Every choice besides Power Off returns me to the same window. What can I do to recover from this?
Background:
So I was trying to update my OP6 to the current OxygenOS while keeping my root using TWRP and Magisk, which I've done in the past without any issue(i.e. go in recovery flash OS, flash current TWRP, reboot back to recovery, flash current Magisk as I understand it). However this time I was running into an issue flashing the Oxygen update getting an error that said it "failed to map file" for the zip. My first instinct was to update TWRP to see if the newest version didn't run into this issue so I flashed that followed by the current Magisk(no reboot in between). After booting back to standard operations everything seemed fine. I went back into recovery and tried the OS update again, but hit the same issue.
I couldn't find anything specific to OP6 with this issue, but similar questions with other devices suggested clearing the dalvik cache, which I tried to no useful effect. Then I came across this thread (forums.oneplus.com/threads/oxygen-os3-i-have-a-problem-please-help.440587/page-2 too new to hyperlink) and did what I think really messed me up which was boldly follow this guy's advice to do an advanced wipe of everything but internal storage(I also left USB storage intact) from TWRP. This failed to fix the issue with the file mapping error when I subsequently tried to flash the update, though I was able to flash TWRP and Magisk successfully again before rebooting and ending up in this loop.
Any assistance in fixing this or general tips on how to not be foolish when messing around with this stuff is greatly appreciated.

Update:
So I followed the advice gleaned from the resourceful person here(https://forum.xda-developers.com/oneplus-6t/help/bootloader-baseband-versions-blank-t3927565) to try working with the device from my computer with fastboot. At first it would recognize the device as "Android" but be unable to find a driver for it and adb/fastboot both failed to recognize it as a device. After installing MiniTool(more as a way to backup what was on the SD card) the proper device driver also got installed and I was able to access it with fastboot; I ran into similar issues as the linked thread above, solved it by switching to b(still failed) then back to a.
Currently I've got it booted into TWRP and I'm working on getting the current Oxygen .zip copied onto the phone storage but the transfer keeps failing after moving a negligible amount.
Update 2:
Via TWRP was able to sideload the current up-to-date standard OS onto it, however my Google backup seems to have decided to disappear on me and the only OP backup I have is ages old. Anyone have recommendations on data recovery tools?

next time just dont change the build.prop file.
serious, it just breaks the system.
heppened to me too.

NickTheHuy said:
next time just dont change the build.prop file.
serious, it just breaks the system.
heppened to me too.
Click to expand...
Click to collapse
Good to know, thanks for the info!
I assume that happened when I messed around with advanced wipe, do you know which of the folders I selected that would have been under? And just for future awareness, would that have not occurred had I just used TWRP's standard wipe instead?

You can run a program that will install 9.0.6 from scratch, running a batch file...
Save my life before yesterday....

Your device is bricked
If able to access the TWRP recovery then boot into twrp and try to get all the data stored in your computer.
Then use the Qualcomm flash tool to completely recover from your hard bricked OP6.
from here https://forum.xda-developers.com/oneplus-6/how-to/op6-collection-unbrick-tools-t3914109
Then its easy, again unlock boot-loader flash TWRP and magisk.

Issues installing LineageOS

Hello and thanks for taking the time to read my post,
after two years I am back at it with android and costum roms. I got an oeplus 6 and started working on it.
Using Linux (POP_OS!) I installed adb and fastboot via apt install.
from there I basically followed this guide: https://wiki.lineageos.org/devices/enchilada/install
Every step was going as it was described but I am struggling with the last step.
The output gets stuck at 47%(the output to the terminal) , than I get an error message on the phone. The terminal shows total xfer. 1.00x.
Those were to be expected according to the wiki, but when I press the return arrow it aborts the installation and I can reboot into a stock system.
What am I doing wrong? I am on the latest update (Android 11), I downloaded the latest nightly.
I also tried to get TWRP on it and then flashing the CROM from there:The TWRP logo is shown but it isnt switching to the swipe so I am stuck. If (TWRP latest, the corresponding installer zip is on my internal storage) i use the older versions I get to QUALCOMM CRASHDUMP mode.

levibuko said:
Hello and thanks for taking the time to read my post,
after two years I am back at it with android and costum roms. I got an oeplus 6 and started working on it.
Using Linux (POP_OS!) I installed adb and fastboot via apt install.
from there I basically followed this guide: https://wiki.lineageos.org/devices/enchilada/install
Every step was going as it was described but I am struggling with the last step.
The output gets stuck at 47%(the output to the terminal) , than I get an error message on the phone. The terminal shows total xfer. 1.00x.
Those were to be expected according to the wiki, but when I press the return arrow it aborts the installation and I can reboot into a stock system.
What am I doing wrong? I am on the latest update (Android 11), I downloaded the latest nightly.
I also tried to get TWRP on it and then flashing the CROM from there:The TWRP logo is shown but it isnt switching to the swipe so I am stuck. If (TWRP latest, the corresponding installer zip is on my internal storage) i use the older versions I get to QUALCOMM CRASHDUMP mode.
Click to expand...
Click to collapse
I was able to install it! I switched to an earlier nightly but I think the difference was that I clicked on apply update -> apply from adb before issuing the command from the terminal.
Now I have a follow up question: how is it these days with root (still magsik?) and can I still instal TWRP( if so, how? I am stuck since the slider is not coming for me)