Related
Execution of this manual at your own risk !!!!
TWRP Install (Custom recovery to install the root files)
1. Install on pc adb and Fastboot driver
2. Install minimal adb and fastboot: https://forum.xda-developers.com/sho....php?t=2317790
3. On the smartphone in the settings, press the Developer mode (Settings-Over the phone-press 8 times on the build number)
4. Under Settings-Developer Options, allow usb-debugging and allow OEM-unlocking (For bootloader unlock)
5. Connect the smartphone to the pc. On the smartphone accepts the adb connection with the pc
6. Starts at Pc Minimal adb and Fastboot. In the command window "adb reboot bootloader" enter and press Enter (restart the smartphone into the bootloader)
7. WARNING: This step deletes all data from the smartphone, returns it to the factory setting and leads to the loss of the warranty !!!! In the command window, type "fastboot oem unlock" and press Enter (turns the boot loader on). The smartphone sits back and restarts. Repeat steps 3 to 6 after restarting
8 Download the Twrp images: https://mega.nz/#!siZhjIKa!OSfglS4Q8...PgKY9vaxthuilo copies the recovery-twrp31jemini.img file to the installation folder of minimal adb and fastboot
9. In the command window, type "fastboot flash recovery recovery-twrp31jemini.img" and press Enter. After successful flashen enter "fastboot reboot" in the command window, press Enter and press the Lauter key on the smartphone (Bring the smartphone to the boot menu)
10. 3 options appear on the smartphone: Recovery, Fastboot, Normal with the Lauter key you navigate to Recovery and press the volume down key to confirm (Smartphone starts now the Installed TWRP Recovery)
11. The recovery is set to Russian, so press the 3ten button from the top (Settings) on the right side, then click on the language icon in the upper right corner and select your preferred language.
Smartphone Roots:
1. Download the root files: https://mega.nz/#!wyQVSbwL!m2arVJbjA...4Nn8LVhDb_AB9Q
2. copy the .zip file to your smartphone, press Install in the recovery, select the copied .zip file and confirm the installation. After flashing the smartphone restart and voila ... your device is rooted
Updates: ( All files from 4pda.ru )
Twrp Flashable zip Update to rom Version V9: https://yadi.sk/d/z8dbqfOM3Jk6w3
Twrp Flashable zip Update to rom Version V18 ( supersu integrated ) : https://yadi.sk/d/jlNSmqYN3L4xHK
I Flashed it over V9 without Wiping and it works for me lika a charm
Flashable Viper4Android : https://drive.google.com/file/d/0B5u-Eac1xV2CYUxqRmxFVkltNms/view?usp=sharing
If you dont need root you can flash V18 with SPflashtool:https://drive.google.com/file/d/0B1kz3pYtoOExSFZ5WGJraFNUYUE/view
At this time there is no working twrp for V18
Custom Rom Doogee Shot (FreemeOS) : https://yadi.sk/d/YklP0V7b3LBFfV
Flash with TWRP at your own risk because i doesnt tried it at my own because V18 runs really smoooth
Expect some Bugs!!!
SPFlashtool FT V23:https://drive.google.com/file/d/0B1kz3pYtoOExemc0VkJtdXZRMVU/view
SPFlashtool FT V18:https://drive.google.com/file/d/0B1kz3pYtoOExSFZ5WGJraFNUYUE/view
I also tried Magisk systemless on V9 and for me it works ( Working modules : Viper4android,dolby atmos,) but on V18 i cant install the new Magisk Framework and get bootloop
If Someone had Problems with SPFlashtool this is how i did it:
Install Spflashtool to C:
Copy flash file to C:
start spflashtool as Admin
select scatter file
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
BTW Sorry for my bad English XD
@Cheese-ass
Greetings and welcome to xda. All posts on xda must be in English, I have translated this one for you but please use google translate for all future post's
Regards
Sawdoctor
Execution of this manual at your own risk !!!!
TWRP Install (Custom recovery to install the root files)
1. Install on pc adb and Fastboot driver
2. Install minimal adb and fastboot: https://forum.xda-developers.com/sho....php?t=2317790
3. On the smartphone in the settings, press the Developer mode (Settings-Over the phone-press 8 times on the build number)
4. Under Settings-Developer Options, allow usb-debugging and allow OEM-unlocking (For bootloader unlock)
5. Connect the smartphone to the pc. On the smartphone accepts the adb connection with the pc
6. Starts at Pc Minimal adb and Fastboot. In the command window "adb reboot bootloader" enter and press Enter (restart the smartphone into the bootloader)
7. WARNING: This step deletes all data from the smartphone, returns it to the factory setting and leads to the loss of the warranty !!!! In the command window, type "fastboot oem unlock" and press Enter (turns the boot loader on). The smartphone sits back and restarts. Repeat steps 3 to 6 after restarting
8 Download the Twrp images: https://mega.nz/#!siZhjIKa!OSfglS4Q8...PgKY9vaxthuilo copies the recovery-twrp31jemini.img file to the installation folder of minimal adb and fastboot
9. In the command window, type "fastboot flash recovery recovery-twrp31jemini.img" and press Enter. After successful flashen enter "fastboot reboot" in the command window, press Enter and press the Lauter key on the smartphone (Bring the smartphone to the boot menu)
10. 3 options appear on the smartphone: Recovery, Fastboot, Normal with the Lauter key you navigate to Recovery and press the volume down key to confirm (Smartphone starts now the Installed TWRP Recovery)
11. The recovery is set to Russian, so press the 3ten button from the top (Settings) on the right side, then click on the language icon in the upper right corner and select your preferred language.
Smartphone Roots:
1. Download the root files: https://mega.nz/#!wyQVSbwL!m2arVJbjA...4Nn8LVhDb_AB9Q
2. copy the .zip file to your smartphone, press Install in the recovery, select the copied .zip file and confirm the installation. After flashing the smartphone restart and voila ... your device is rooted
There is a way to connect a lan usb adapter?
fantastic work like a charm, but used recovery download from the german one and worked rooted oukitel k6000 plus yea
i follow every step ( iread many times before i do it)
But Phone dosent boot anymore
I got only this Message on Display :
Orange State
yor device has been unlocked and cant ve trust
your device will reboot in 5 seconds
But Nothing happend
When i try to flash stock rom with splash tool i got da brom error with 60002
Its bricked???
Worked fine. I had to download files from other websites, but this procedure was good.
After reboot, su was working fine in /system. I wanted to reset the device completely, and typed "fastboot oem unlock"; I thought it would wipe data. Now, phone only boots on TWRP, and it seems like the /data partition is broken. TWRP can mount /system, but not /data. Either the device node is missig, or the partition is not formated properly.
Code:
# cat /etc/fstab
/dev/block/mmcblk0p6 /nvdata ext4 rw 0 0
/dev/block/mmcblk0p8 /protect_f ext4 rw 0 0
/dev/block/mmcblk0p9 /protect_s ext4 rw 0 0
/dev/block/mmcblk0p26 /system ext4 rw 0 0
/dev/block/mmcblk0p27 /cache ext4 rw 0 0
/dev/block/dm-0 /data ext4 rw 0 0
/external_sd auto rw 0 0
/usbotg auto rw 0 0
Losetup-a gives nothing.
I tried all possible commands (adb reboot to everything), and press volume up or down ... always get back in TWRP. Can not even reach the factory menu (the one where there are tests).
After reformating /data i can reboot to bootloader (fastboot), but still not /system.
Stock ROM was looking fine; I would like to be able to keep it. I would like to avoid flashing to an other ROM.
In short, I have TWRP and flashboot, but /system launches TWRP.
I don't know how to get a working system. SPFlashTool does not seem to work with TWRP installed. TWRP does not like OUKITEL_K6000_Plus_V6.0_20170519.rar. I can't find any ZIP ROM for TWRP. And when I try individual .img files from the RAR, TWRP can install them, but it does notproduce a working phone.
I fear something could be wrong with the partition table, or at least /data. /system contains many files and this looks good.
---------- Post added at 01:30 PM ---------- Previous post was at 12:40 PM ----------
How I fixed it:
fastboot flash boot /tmp/OUKITEL_K6000_Plus_V6.0_20170519/recovery-verified.img (EDIT: this MUST be wrong, should be fastboot flash recovery /tmp/OUKITEL_K6000_Plus_V6.0_20170519/recovery-verified.img or fastboot flash boot /tmp/OUKITEL_K6000_Plus_V6.0_20170519/boot-verified.img )
then, perform again https://fvknl.pro/k6000-plus-v6-0-upgrade/
and now I have a working phone.
* Can't apply Android updates because of TWRP+SuperSU ?
Now that my phone works, and is rooted (i use the stock ROM version 6), may 19th, the system is telling me there are system updates to do. I have downloaded them (200MB), but after reboot, update fails, for obvious reasons: the update is designed to be installed by the stock recovery firmware; and that partition is overwritten by TWRP.
I was given a tip to work around this (wherer the img file is taken from the .rar archive of the stock ROM):
# fastboot boot /tmp/recovery-verified.img
and it worked: fastboot uploaded the recovery image to the phone, ran it, and that recovery firmware started to apply the update.
Started ... but failed before half of it ... PROBABLY because /system was HEAVILY modified while I asked TWRP to install UPDATE-SuperSU-v2.82-20170528234214.zip (read the installation log of SuperSU ... it alters many things).
How can I apply my android updates without erasing the whole phone each time I want to apply them ?
A: how to get the installation log, to see the failure point, and fix it manually
or
B: install the update manually without running the recovery, but extract the update file, and manually copy the new files at due place, one by one
or
C: how to undo installation of SuperSU, so that /system is in a state where the update can be applied.
I want to do this without erasing /data, or /system. I had this issue on my previous phone; since december 2014 I could not apply any Android update; so my phone is stuck to Android 4 from december 2014. There have been many changes and updates during 2015 and I could not apply them. After installing su, i had been able to perform two Android updates; updates broke after installing Xposed. I do not want my new K6000 to have the same issue; I want to find a way to apply updates. And I would like to keep the stock flavour because there are many features I would like to use (don't want to install misc ROMs).
Xposed for oukitel 6000plus root
Hi I have an oukitel 6000plus root. I can not find the way to install xposed. You have succeeded in installing it successfully? Send me my email address app and zip to use. Thanks Fabio
no xposed for k6000 plus
patpix75 said:
Hi I have an oukitel 6000plus root. I can not find the way to install xposed. You have succeeded in installing it successfully? Send me my email address app and zip to use. Thanks Fabio
Click to expand...
Click to collapse
sorry latest xposed is for sdk 25 and the latest firmware for this device is android 7.0 (Sdk 24)
patpix75 said:
Hi I have an oukitel 6000plus root. I can not find the way to install xposed. You have succeeded in installing it successfully? Send me my email address app and zip to use. Thanks Fabio
Click to expand...
Click to collapse
I have tried many random things; I forgot the details of it. The versions are not a problem; there are links around to download old installers. Even if latest Xposed is for Android 25, archives will let you download v24.
It also depends when you rooted your phone, and which updates you did on your ROM before rooting. Depends if you are using ROM v6, v9, or v18 ...
Also, even if Xposed is installed, it's not working properly; in particular, I wanted Xposed to NotifyClean, and this plugin could not be installed on the Xposed I have (download goes fine, but plugin complains I need reboot to activate it). So, in short, Xposed is useless for me for now. Some other plugins have installed correctly (Taskbar).
The Xposed I have NOW is version 87 by PurifyOS. ATM, Android API 24.
But I said I tried many random things, so, maybe having tried to installed other variations of Xposed by other people was important to have this one installed. I remember that at some point, trying to install this one (purify) failed, and then, worked later ... forgot why.
Error
When you try to upload a TWRP, a message pops up:
"error: cannot load 'recovery-twrp31jemini.img'"
Bootloader should be unlocked. I see a buzz when switching on "yor device has been unlocked and cant ve trust
your device will reboot in 5 seconds"
Phone has a ROM v18
Application procedure on W10.
Does anyone find any solution?
You don't need to burn TWRP in FLASH to be able to use it. You just need to load and run it, this way:
fastboot boot recovery_TWRP-3.1.0.img
This way, if you have backup your whole phone, or downloaded and extracted a ROM, you can boot a stock recovery image:
fastboot boot /tmp/recovery-verified.img
According to your name jemini ... I thjink you have downlaoded the wrong TWRP. Boot and flash may fail if you grabbed a file for an other phone.
This should be ROM independant.
Since I rarely use TWRP, I now keep the stock recovery, and run TWRP from fastboot only when I need it; this way, stock recovery is available for Android updates.
Do you have links to ROM v18, so that I can download and install it directly, instead of having to burn v6, then update to v9 and v18 via update process ? I have issues with updates, and would like to flash directly using v18; but could not find a download link.
I got the phone today and unlocked it for root and everything.
After
Code:
fastboot oem unlock
the following showed up:
Code:
...
(bootloader) Start unlock flow
OKAY [ 14.791s]
finished. total time: 14.792s
Problem is now:
Orange state
Your device has been unlocked and can't be trust
Your device will boot in 5 seconds.
But it's not booting, just stuck at this screen.
Any help very much appreciated!
EDIT:
I was on V23 ROM which came per OTA.
EDIT-2:
I was able to flash it back to V23 with flashtool, but no root. Bootloader seems to be unlocked, the message still appears.
rom
"Custom Rom Doogee Shot (FreemeOS) :
Flash with TWRP at your own risk because i doesnt tried it at my own because V18 runs really smoooth
Expect some Bugs!!!""""
What do you say that this rom picks up on the oukitel k6000 plus ??
I need someone to help me my k6000 plus did not call any more after this procedure.
when I install the rom stock by flash sp this error appears
https://drive.google.com/file/d/0ByEkRDgYmbWtOXdpbngtcGJxQk0/view?usp=sharing
What do you want to do?
Flash the Stock ROM back with flashtool?
You should switch to "Download Only" and not "Firmware Upgrade".
Also the Download Agent was different when I flashed it, it was DA_PL.bin.
cojo11 said:
i follow every step ( iread many times before i do it)
But Phone dosent boot anymore
I got only this Message on Display :
Orange State
yor device has been unlocked and cant ve trust
your device will reboot in 5 seconds
But Nothing happend
When i try to flash stock rom with splash tool i got da brom error with 60002
Its bricked???
Click to expand...
Click to collapse
SIVAKUMAR: yes my mobile also same problem ...boot loop please help me oukitel k6000 plus MT6750T
------------- Orange State----------------
yor device has been unlocked and cant ve trust
your device will reboot in 5 seconds:crying:
---------- Post added at 11:14 AM ---------- Previous post was at 11:11 AM ----------
sivakumarindia said:
SIVAKUMAR: yes my mobile also same problem ...MT6750T
------------- Orange State----------------
yor device has been unlocked and cant ve trust
your device will reboot in 5 seconds:crying:
Click to expand...
Click to collapse
SIVAKUMAR: I THINK THIS ROM DIFFERENT MT6750 AND MT6750T:crying:
---------- Post added at 11:19 AM ---------- Previous post was at 11:14 AM ----------
rolex0815 said:
i got the phone today and unlocked it for root and everything.
After
Code:
fastboot oem unlock
the following showed up:
Code:
...
(bootloader) start unlock flow
okay [ 14.791s]
finished. Total time: 14.792s
problem is now:
orange state
your device has been unlocked and can't be trust
your device will boot in 5 seconds.
but it's not booting, just stuck at this screen.
Any help very much appreciated!
Edit:
I was on v23 rom which came per ota.
Edit-2:
I was able to flash it back to v23 with flashtool, but no root. Bootloader seems to be unlocked, the message still appears.
Click to expand...
Click to collapse
sivakumar: My mobile also same condition boot loop
I got the same and this help me :
For this case, leave SP tool setting as normal. Before connect USB to device:
1. Press and hold vol +
2. Connect USB to device and hold vol + button.
3. Just release the button until you see the download process start working.
with this solution i have Flaht the v6 rom
Boot loop try this Back to STOCK ROM
Cheese-ass said:
Execution of this manual at your own risk !!!!
TWRP Install (Custom recovery to install the root files)
1. Install on pc adb and Fastboot driver
2. Install minimal adb and fastboot: https://forum.xda-developers.com/sho....php?t=2317790
3. On the smartphone in the settings, press the Developer mode (Settings-Over the phone-press 8 times on the build number)
4. Under Settings-Developer Options, allow usb-debugging and allow OEM-unlocking (For bootloader unlock)
5. Connect the smartphone to the pc. On the smartphone accepts the adb connection with the pc
6. Starts at Pc Minimal adb and Fastboot. In the command window "adb reboot bootloader" enter and press Enter (restart the smartphone into the bootloader)
7. WARNING: This step deletes all data from the smartphone, returns it to the factory setting and leads to the loss of the warranty !!!! In the command window, type "fastboot oem unlock" and press Enter (turns the boot loader on). The smartphone sits back and restarts. Repeat steps 3 to 6 after restarting
8 Download the Twrp images: https://mega.nz/#!siZhjIKa!OSfglS4Q8...PgKY9vaxthuilo copies the recovery-twrp31jemini.img file to the installation folder of minimal adb and fastboot
9. In the command window, type "fastboot flash recovery recovery-twrp31jemini.img" and press Enter. After successful flashen enter "fastboot reboot" in the command window, press Enter and press the Lauter key on the smartphone (Bring the smartphone to the boot menu)
10. 3 options appear on the smartphone: Recovery, Fastboot, Normal with the Lauter key you navigate to Recovery and press the volume down key to confirm (Smartphone starts now the Installed TWRP Recovery)
11. The recovery is set to Russian, so press the 3ten button from the top (Settings) on the right side, then click on the language icon in the upper right corner and select your preferred language.
Smartphone Roots:
1. Download the root files: https://mega.nz/#!wyQVSbwL!m2arVJbjA...4Nn8LVhDb_AB9Q
2. copy the .zip file to your smartphone, press Install in the recovery, select the copied .zip file and confirm the installation. After flashing the smartphone restart and voila ... your device is rooted
Updates: ( All files from 4pda.ru )
Twrp Flashable zip Update to rom Version V9: https://yadi.sk/d/z8dbqfOM3Jk6w3
Twrp Flashable zip Update to rom Version V18 ( supersu integrated ) : https://yadi.sk/d/jlNSmqYN3L4xHK
I Flashed it over V9 without Wiping and it works for me lika a charm
Flashable Viper4Android : https://drive.google.com/file/d/0B5u-Eac1xV2CYUxqRmxFVkltNms/view?usp=sharing
If you dont need root you can flash V18 with SPflashtool:https://drive.google.com/file/d/0B1kz3pYtoOExSFZ5WGJraFNUYUE/view
At this time there is no working twrp for V18
Custom Rom Doogee Shot (FreemeOS) : https://yadi.sk/d/YklP0V7b3LBFfV
Flash with TWRP at your own risk because i doesnt tried it at my own because V18 runs really smoooth
Expect some Bugs!!!
SPFlashtool FT V23:https://drive.google.com/file/d/0B1kz3pYtoOExemc0VkJtdXZRMVU/view
SPFlashtool FT V18:https://drive.google.com/file/d/0B1kz3pYtoOExSFZ5WGJraFNUYUE/view
I also tried Magisk systemless on V9 and for me it works ( Working modules : Viper4android,dolby atmos,) but on V18 i cant install the new Magisk Framework and get bootloop
If Someone had Problems with SPFlashtool this is how i did it:
Install Spflashtool to C:
Copy flash file to C:
start spflashtool as Admin
select scatter file
BTW Sorry for my bad English XD
Click to expand...
Click to collapse
SIVAKUMAR INDIA: BOOT LOOP TRY THIS BACK TO STOCK ROM OUKITEL K6000 PLUS MT6750T
----------------------------ERROR BOOT LOOP -------------------------------------------
Orange State
yor device has been unlocked and cant ve trust
your device will reboot in 5 seconds
---------------------------TRY THIS STEPS RECOVERED STOCK ROM--------------------------
step1: Vcom+SPD+and+adb+driver+Installer+Windows+8_10
INSTALL DRIVERS
step2; SP_MDT_v3.1732 (DOWNLOAD )
EXTRACT AND RUN SP-MDT FLASH ,
SCAN ---------CONNECT MOBILE------FLASH SUCCEED----
step3: OUKITEL_K6000_Plus_V23_20170726
THIS LINK AVAILABLE OLD VERSION SP_MDT ONELY SEARCH AND DOWNLOAD NEW VERSION SP_MDT_v3.1732
LINKS: https://www.oukitel.com/latest-software-rom-for-all-oukitel-devices-48.html
This guide explains how to install custom recovery [TWRP] on Nubia NX512J (Z9Max) device.
This uses a simple and handy tool made by [email protected] to install the TWRP as well as stock recovery on nx512j
The tool supports 3 versions of TWRP to be installed and 3 versions of stock recovery from v2.04, v9.20 & v9.21.
This also means that you can switch from TWRP to stock recovery if you want use stock firmware and vice versa.
The emmc_appsboot.mbn for TWRP and Stock recovery has different layouts this why for stock firmware, stock recovery with specific emmc_appsboot.mbn is required.
while for TWRP modified emmc_appsboot.mbn is required. The tool provides both options.
To begin this you will need following:-
1. Windows computer
2. USB Cable
3. of-course NX512J phone
Steps :-
1. First download the following zip from https://yadi.sk/d/ep-d0Lc63Hgnzr or from https://www.androidfilehost.com/?fid=889764386195916618 maintained by ilya_rat
2. Extract the zip file on your computer wherever you wish
3. Navigate to the extracted folder (Flash_recovery )
4. Run the install_recovery.bat file
5. A window will open showing several options. See the attached picture
6. If you do not have Fast-boot and ADB drivers installed then choose appropriate number and press enter to install the "USB drivers"
7. Power up your phone in fast-boot mode by pressing Power and Volume down button while phone is off until a menu option with nubia logo appears this is fastboot mode
8. A countdown timer can be seen on the fastboot page which restarts the phone after 10 seconds. Press volume up or down key to disable the countdown timer
9. Now connect the phone to PC using USB cable and enter your choice to install the stock recovery or TWRP. For example Choosing 3 option will install " TWRP 3.1.0.0"
10. A message will show that everything is OK if the TWRP is installed. You can reboot the phone to recovery mode from the bootloader menu by navigating using volume keys and using power button to select the option.
now you will greeted with TWRP from here on you can install any custom firmware or root your phone as you wish.
The official version of TWRP can be found at Teamwin website https://twrp.me/devices/nubianx512j.html
Remember:- If you plan to use stock firmware you must install the stock recovery using the tool and install the stock firmware. TWRP is only and only for any custom firmware due to different emmc_appsboot.mbn layout
The commands used in this tool
To install recovery
Code:
fastboot -i 0x19d2 flash recovery twrp*.img
where twrp*.img is the name of twrp recovery image
To install aboot [emmc_appsboot.mbn]
Code:
fastboot.exe -i 0x19d2 flash aboot emmc_appsboot.mbn
Credits
bauuuuu
[email protected]
teamwin team
Donde puedo descargar la aplicacion en version ingles o español
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
which button(s) shoud i press on the installer?
when i press on the installer i have a lot of buttons(install miracle,install spd etc)
which i shoud i press?
and will it work on windows 7?
thanks
Hey there!
I would like to root this using a linux desktop, could you explain the process in more detail which tool is responsible for which function so I could try to adapt the process to function without a windows desktop?
kaefert said:
Hey there!
I would like to root this using a linux desktop, could you explain the process in more detail which tool is responsible for which function so I could try to adapt the process to function without a windows desktop?
Click to expand...
Click to collapse
Hi,
if you are running a debian based distro, you have first to install adb and fastboot from manager or using apt-get.
2/ check if file /etc/udev/rules.d/51-android.rules is present and contains correct description of your phone idVendor and idProduct
if not run lsusb and add the following line
Code:
SUBSYSTEMS=="usb", ATTRS{idVendor}=="your idVendor", ATTRS{idProduct}=="your idProduct", MODE="0666" GROUP="androiddev", SYMLINK+="android%n"
3/ service udev restart
4/ unplug and plug again your phone and run adb devices, it will show a long number and letters with UNAUTHORIZED. that's OK
5/enter fastboot mode and unlock your bootloader with : fastboot oem unlock
6/ enter fastboot mode when booting your phone and type this: fastboot flash recovery recovery.img
( you have to rename twrp.img to recovery.img)
that's done you can now boot to twrp and install su.
hey there avrmge!
thanks for the reply, but I already sent the device back to the seller, it was too far below my expectations.
kaefert said:
hey there avrmge!
thanks for the reply, but I already sent the device back to the seller, it was too far below my expectations.
Click to expand...
Click to collapse
Hello,
the procedure above generally works with any other android device,
i think the main problem with this phone is lack of notification led, no 3.5mm jack and sometimes battery drains too fast. except that, it is as normal as other models in same segment. what were your expectations ?
well, I was disappointed with the problems you mentioned and also:
-) no light sensor ( --> no automatic brightness)
-) accelerometer has only 2 axis working
-) no gyroscope
-) no proximity sensor
boot loop after root ! Ur guide to the hell
mark332 said:
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
Click to expand...
Click to collapse
I need help, when i try to install the vcom drivers, i get an error. i can,t post image so...
can you add video?
how to imei change?
Maybe it's not the place but is there someone who get complain on that the speaker is so low can I increase it and make it louder cause people say we can't here you please help
mark332 said:
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
Click to expand...
Click to collapse
I am having problems with twrp when installing and starting in recovery mode it freezes me forcing to restart the device
mark332 said:
Guys This is the Guide to Root Leagoo KIICAA Mix-
Download Require Files-
1. Download SP flash tools https://androidfilehost.com/?fid=745425885120763929
2. V Com Driver Require https://androidfilehost.com/?fid=817550096634801170
3. twrp Require https://romprovider.com/2017/10/t-root-leagoo-kiicaa-mix/
4. Supersu Require https://forum.xda-developers.com/apps/supersu/v2-64-2-66-supersu-mode-t3286120
Instructions-
1. Install VCom Driver
2. Run SP flash tools and Load scatter from Recovery folder
3. check recovery only and under recovery section load twrp.img
4. click Download, and connect switched off Phone to PC
5. wait for success. Done twrp installed.
6. reboot to twrp by holding power and volume+ button
7. create a nandroid backup
8. flash supersu.zip, done successfully Rooted.
i hope You will get success.
Click to expand...
Click to collapse
when i open twrp, it asks for a password. my phone doesn't have any password, and i need it to install a custom rom. is there someone able to help me? bc i really can't understand
*im assuming that i have to unlock oem, but is it really necessary?
Ciao, ho installato la twrp tutto a posto, poi ho messo pixel 1.2 rom, ma audio in telefonata pessimo mi serve un aiuto per migliorare grazie
I installed a proper twrp (fastboot flash)
Leagoo KIICAA Mix 3.1
MediaFire is a simple to use free service that lets you put all your photos, documents, music, and video in a single place so you can access them anywhere and share them everywhere.
www.mediafire.com
hello guys
Sorry for my english , but i'll try to do my best .
Today i explain , how you unlock and root your medion x1030X device.
i'm no responsable for bricking devices etc.........
Make sure you have downloaded the stockrom and the flashtool from the medion site.
if you don't know how adb and fastboot works than leave it and don't try it.
what do you need
-magisk.zip
link : https://mega.nz/#!dEQVES4Y!1A_7iJu57OLiMwdGv-1hPFliaR53Wb90z8EeR1qat9M
-externalsdcard
-philz touch recovery.img
link : https://mega.nz/#!kYBVjJ5Y!IZfLvWa1Ca7KHLZG4VSqRRUqHKi_7P8_aO38MusJedY
First off all install fastboot and adb drivers on your pc.
There are many tutorials here on xda.
- go to settings , about tablet(the last option), click several times on build
number.
- No go one step back and you see that's there is a new option (developer
options)
- Open this and enable oem unlocking and usb debugging.
- connect the tablet too the pc and enable media transfer.
- now you see a usb debugging popup , allow it .
- CONGRATS THE FIRST STAGE IS COMPLETE.
- Now open een adb shell.
- type now adb reboot bootloader.
- the tablet reboots to fastboot mode now.
-Type now in the adb console(pc) fastboot oem unlock.
- On the tablet follow the instructions for unlocking.
- Type in adb shell type now fastboot reboot.
- The tablet reboots twice and then FORMAT THE DEVICE TOO FACTORY AGAIN.
- Setup again your tablet. and activate again developer options and usb
debugging in settings.
-download now magisk.zip file and copy it to a external sdcard and place it in
the tablet.
THE LAST PART NOW.
-reboot the tablet again in fastboot mode.(see earlier instructions)
-type in the adb shell now , fastboot flash recovery recovery.img (make sure
thats the recovery.img is placed where you open the adb shell window)
otherwise fastboot will not find the recovery.img.
-now reboot the device and hold volume up for selecting the recovery.
-Once entering the philz recovery go to format options and select format data.
-Now the internaldata can be mounted without errors.
-Go now to intall zip and install magisk.zip
Congrats your device is now rooted and fully unlocked .
REBOOT ONCE AGAIN AND SETUPTHE TABLET FOR THE LAST TIME.
ENJOY!!!!!!!!!!!!!!!!!
(removed)
Hi @snakekiller!
Many thanks for your tutorial / howto to unlock and root my Medion X10302 tablet.
It worked! Now I have a really good recovery and Magisk running.
I had to install anyways because the tablet got so slow sometimes I had to reboot. I guess it was the fault of some bad behaving app or from fragmentation of my emmc.
A new custom rom would be on my wishlist but this is good enough fro what I need it for.
If anyone has success with a custom rom for the X1030x please comment.
So thanks again,
greenoid
I have a little problem with rooting and Magisk:
Your magisk.zip somehow installs a SuperSU su binary together with the Magisk app in version 15.
No the Magisk app checks for updates and after 2 updates I'm at the current version 23.
If I start it it complains "Abnormal State...Please remove the other unsupported su."
Because Magisk does not support SuperSU binary since version 13 I've read and needs to use its own.
There's a script to uninstall SuperSU, but it needs to flash a stock boot.img afterwards.
I don't have the stock firmware from my OTA v2.11. Online from Medion there's only firmware v2.5.
Magisk did a backup of the boot.img, but I don't now the status of this image. I did a backup of it so far.
If this boot.img.gz does already contain changes made by SuperSU I wont get far.
I can't run Titanium Backup or other apps a root. But I can get root on an adb shell.
What should I do to switch to a clean and functioning Magisk from here?
I solved my Magisk problem.
I got the v2.11 OTA files from support at the Medion community admin
LIFETAB X1030X Firmware V2.11
Hallo allerseits, wir haben das Update auf die Firmware Version 2.11 für unser LIFETAB X1030X veröffentlich. Die Release Notes findet Ihr weiter unten. Entgegen unseren üblichen Gepflogenheiten ging das Update bereits vor Weihnachten in eine stille Betaphase und ist jetzt allgemein verfügbar...
community.medion.com
First I tried a dirty flash of the boot partition. This ended in a rather scary boot loop.
In the end I flashed it all over and began anew.
Here's what I changed compared to the howto above:
- download Magisk-23.apk and rename it Magisk-23.zip
- copy it the external SD-Card
- install that while being in recovery
- before you reboot from phils recovery, don't say yes to install root/SuperSU!
- afterwards go to settings and allow thrid party apks.
- start Magisk app (stub) and download the real app
Now I've really rooted the tablet. Apps needing root will prompt a dialog asking for access,.
Google Play does work.
Disclaimer
These kind of modifications are not for the faint of heart!!! Flash/modify at your own risk!!! I will not be responsible for bricked phones, Dead batteries, world war 3, yada yada yada..... you Know the Rest.
Click to expand...
Click to collapse
Introduction
After finding this amazing device (LKM-EMW) for a very cheap price (90 euros new), I made the fatal mistake of updating through OTA to the Latest Android 10 version 00f.
So where is the Problem?? The latest .DZ from the KDZ firmware wasn't extractable through any tool or script I could find anywhere online, Only the Android 9 ROM was working, but Downgrading through LGUP or LG Flash tool was very risky!!!! (due to ARB protection).
Since this phone's Fastboot mode was replaced with LG's own DOWNLOAD mode, using Fastboot commands to flash the Magisk's patched boot image was impossible. QFIL was also not a possibility, Considering it ships with a MTK chipset, and using SP flash tool will require This phone's particular Scatter file and a signed DA from LG to work, leaving me with no other choices for obtaining Root access.
That is, until I found the following tool: mtkclient by bkerler.
Prerequisites
backup of your DATA. (during and after unlocking the Bootloader, your data partition must be wiped!!!!)
Preferably a Windows PC (you will need LGUP in case something goes wrong anyways).
MTK ALL-in-one 1.0.8 drivers and LG's drivers installed.
mtkclient installed and running (don't ask me how-to, the Github page is pretty self explanatory).
This Magisk Alpha Build patched for MTK downloaded for installation.
Since this device uses an A/B partitioning system, you need to know which slot is the active one. Using this App, under the System tab, you can find out which one is active. Mine was _b slot.
and above all.... Patience.
Unlocking the Bootloader
(please note, using python [command] didn't work for me for some reason. However, using py [command] worked for me. Use what works!)
Turn on OEM Unlocking and USB Debugging in Developers Options.
Turn off your phone and remove sim/sdcard.
launch cmd inside the mtkclient folder or cd into it.
backup your Preloader by using: py mtk dumppreloader --filename=preloader.bin.
connect your phone turned off while holding the Volume Down + the Assistant buttons to boot into BROM mode. The Preloader backup will run automatically.
After it's complete, disconnect your device's cable. You will need to do this after every step.
Run the command: py mtk e metadata,userdata and connect while holding the button combo. Wait for it to complete.
Disconnect again, then run: py mtk xflash seccfg unlock and reconnect.
If successful, your device's Bootloader is now unlocked!!!
Rooting
Knowing which active slot you're booting into will change the next steps slightly. If it's _a, then all following commands will have an _a instead of _b .
Before rebooting after unlocking, use the command: py mtk r boot_b,vbmeta_b boot_b.bin,vbmeta_b.bin to backup your boot and vbmeta partitions respectively. (you will find them in the mtkclient folder afterwards!!)
reboot your phone. a warning screen will show up, don't panic!!!. It will ask you to Factory reset the phone upon successfully booting. Do it and reboot.
Setup your phone normally, then install the aforementioned Magisk APK.
Transfer the backed up boot.bin to your phone and patch it manually inside Magisk.
Transfer the Patched boot image back to your mtkclient folder and rename to i.e boot_magisk.bin.
Turn off your device and launch the command: py mtk w boot_b,vbmeta_b boot_magisk.bin,vbmeta.img.empty. Connect the phone.
when done, reboot your phone and launch Magisk. It will ask you to reinstall itself to complete the setup. Ignore the warning.
Go to Settings and switch to the Beta Update Channel, Reinstall Magisk 23.0 beta and Magisk manager again.
If successful, Your phone is now rooted.
Passing SafetynetAPI
Turn on Magisk Hide and repack Magisk Manager from Settings.
Install latest Riru core from Manager.
Install this Universal Safetynet fix by kdrag0n.
reboot and enjoy!!
Credits for all of this goes to:
bkerler for his awesome Tool, none of this is possible w/o it.
Topjohnwu for Magisk.
@kdrag0n for his Safetynet fix.
Slim K said:
Disclaimer
Introduction
After finding this amazing device (LKM-EMW) for a very cheap price (90 euros new), I made the fatal mistake of updating through OTA to the Latest Android 10 version 00f.
So where is the Problem?? The latest .DZ from the KDZ firmware wasn't extractable through any tool or script I could find anywhere online, Only the Android 9 ROM was working, but Downgrading through LGUP or LG Flash tool was very risky!!!! (due to ARB protection).
Since this phone's Fastboot mode was replaced with LG's own DOWNLOAD mode, using Fastboot commands to flash the Magisk's patched boot image was impossible. QFIL was also not a possibility, Considering it ships with a MTK chipset, and using SP flash tool will require This phone's particular Scatter file and a signed DA from LG to work, leaving me with no other choices for obtaining Root access.
That is, until I found the following tool: mtkclient by bkerler.
Prerequisites
backup of your DATA. (during and after unlocking the Bootloader, your data partition must be wiped!!!!)
Preferably a Windows PC (you will need LGUP in case something goes wrong anyways).
MTK ALL-in-one 1.0.8 drivers and LG's drivers installed.
mtkclient installed and running (don't ask me how-to, the Github page is pretty self explanatory).
This Magisk Alpha Build patched for MTK downloaded for installation.
Since this device uses an A/B partitioning system, you need to know which slot is the active one. Using this App, under the System tab, you can find out which one is active. Mine was _b slot.
and above all.... Patience.
Unlocking the Bootloader
(please note, using python [command] didn't work for me for some reason. However, using py [command] worked for me. Use what works!)
Turn on OEM Unlocking and USB Debugging in Developers Options.
Turn off your phone and remove sim/sdcard.
launch cmd inside the mtkclient folder or cd into it.
backup your Preloader by using: py mtk dumppreloader --filename=preloader.bin.
connect your phone turned off while holding the Volume Down + the Assistant buttons to boot into BROM mode. The Preloader backup will run automatically.
After it's complete, disconnect your device's cable. You will need to do this after every step.
Run the command: py mtk e metadata,userdata and connect while holding the button combo. Wait for it to complete.
Disconnect again, then run: py mtk xflash seccfg unlock and reconnect.
If successful, your device's Bootloader is now unlocked!!!
Rooting
Knowing which active slot you're booting into will change the next steps slightly. If it's _a, then all following commands will have an _a instead of _b .
Before rebooting after unlocking, use the command: py mtk r boot_b,vbmeta_b boot_b.bin,vbmeta_b.bin to backup your boot and vbmeta partitions respectively. (you will find them in the mtkclient folder afterwards!!)
reboot your phone. a warning screen will show up, don't panic!!!. It will ask you to Factory reset the phone upon successfully booting. Do it and reboot.
Setup your phone normally, then install the aforementioned Magisk APK.
Transfer the backed up boot.bin to your phone and patch it manually inside Magisk.
Transfer the Patched boot image back to your mtkclient folder and rename to i.e boot_magisk.bin.
Turn off your device and launch the command: py mtk w boot_b,vbmeta_b boot_magisk.bin,vbmeta.img.empty. Connect the phone.
when done, reboot your phone and launch Magisk. It will ask you to reinstall itself to complete the setup. Ignore the warning.
Go to Settings and switch to the Beta Update Channel, Reinstall Magisk 23.0 beta and Magisk manager again.
Se for bem sucedido, seu telefone está agora enraizado.
Passing SafetynetAPI
Turn on Magisk Hide and repack Magisk Manager from Settings.
Instale o núcleo riru mais recente do Manager.
Instale esta correção Universal Safetynet por kdrag0n.
reiniciar e desfrutar!!
Créditos para tudo isso vai para:
bkerler for his awesome Tool, none of this is possible w/o it.
Topjohnwu para Magisk.
@kdrag0n for his Safetynet fix.
Click to expand...
Click to collapse
Slim K said:
Disclaimer
Introduction
After finding this amazing device (LKM-EMW) for a very cheap price (90 euros new), I made the fatal mistake of updating through OTA to the Latest Android 10 version 00f.
So where is the Problem?? The latest .DZ from the KDZ firmware wasn't extractable through any tool or script I could find anywhere online, Only the Android 9 ROM was working, but Downgrading through LGUP or LG Flash tool was very risky!!!! (due to ARB protection).
Since this phone's Fastboot mode was replaced with LG's own DOWNLOAD mode, using Fastboot commands to flash the Magisk's patched boot image was impossible. QFIL was also not a possibility, Considering it ships with a MTK chipset, and using SP flash tool will require This phone's particular Scatter file and a signed DA from LG to work, leaving me with no other choices for obtaining Root access.
That is, until I found the following tool: mtkclient by bkerler.
Prerequisites
backup of your DATA. (during and after unlocking the Bootloader, your data partition must be wiped!!!!)
Preferably a Windows PC (you will need LGUP in case something goes wrong anyways).
MTK ALL-in-one 1.0.8 drivers and LG's drivers installed.
mtkclient installed and running (don't ask me how-to, the Github page is pretty self explanatory).
This Magisk Alpha Build patched for MTK downloaded for installation.
Since this device uses an A/B partitioning system, you need to know which slot is the active one. Using this App, under the System tab, you can find out which one is active. Mine was _b slot.
and above all.... Patience.
Unlocking the Bootloader
(please note, using python [command] didn't work for me for some reason. However, using py [command] worked for me. Use what works!)
Turn on OEM Unlocking and USB Debugging in Developers Options.
Turn off your phone and remove sim/sdcard.
launch cmd inside the mtkclient folder or cd into it.
backup your Preloader by using: py mtk dumppreloader --filename=preloader.bin.
connect your phone turned off while holding the Volume Down + the Assistant buttons to boot into BROM mode. The Preloader backup will run automatically.
After it's complete, disconnect your device's cable. You will need to do this after every step.
Run the command: py mtk e metadata,userdata and connect while holding the button combo. Wait for it to complete.
Disconnect again, then run: py mtk xflash seccfg unlock and reconnect.
If successful, your device's Bootloader is now unlocked!!!
Rooting
Knowing which active slot you're booting into will change the next steps slightly. If it's _a, then all following commands will have an _a instead of _b .
Before rebooting after unlocking, use the command: py mtk r boot_b,vbmeta_b boot_b.bin,vbmeta_b.bin to backup your boot and vbmeta partitions respectively. (you will find them in the mtkclient folder afterwards!!)
reboot your phone. a warning screen will show up, don't panic!!!. It will ask you to Factory reset the phone upon successfully booting. Do it and reboot.
Setup your phone normally, then install the aforementioned Magisk APK.
Transfer the backed up boot.bin to your phone and patch it manually inside Magisk.
Transfer the Patched boot image back to your mtkclient folder and rename to i.e boot_magisk.bin.
Turn off your device and launch the command: py mtk w boot_b,vbmeta_b boot_magisk.bin,vbmeta.img.empty. Connect the phone.
when done, reboot your phone and launch Magisk. It will ask you to reinstall itself to complete the setup. Ignore the warning.
Go to Settings and switch to the Beta Update Channel, Reinstall Magisk 23.0 beta and Magisk manager again.
If successful, Your phone is now rooted.
Passing SafetynetAPI
Turn on Magisk Hide and repack Magisk Manager from Settings.
Install latest Riru core from Manager.
Install this Universal Safetynet fix by kdrag0n.
reboot and enjoy!!
Credits for all of this goes to:
bkerler for his awesome Tool, none of this is possible w/o it.
Topjohnwu for Magisk.
@kdrag0n for his Safetynet fix.
Click to expand...
Click to collapse
hello everyone, View attachment 5430177at the beginning the commands to unlock the bootloader, py (comand) = is to write py unlock bootloader?
[email protected] said:
hello everyone, View attachment 5430177at the beginning the commands to unlock the bootloader, py (comand) = is to write py unlock bootloader?
Click to expand...
Click to collapse
I don't understand your question. Can you use a better translator/formulate the question clearly? Also, if such a command existed, why would I write 3 paragraphs and a Guide?
My advice, go to the Github page of the tool and read/learn how the tool works first, then come back here if you're stuck.
Thx for this guide! my backup phone k41s is finally rooted
You are a very smart person. We finally have root for LGk41s (WORKS in K51s too).
Thanks!
Does this work on a provider locked LG K40?
Tem como flashear GSIs?
I was able to root my LG K51 from T-Mobile by following this guide.
I appreciate it!
It's don't work to LG K40S (Android 9 and 10), if you brick your phone u can reset them with:
*Backup command (Depend of which active slot, u use command with a or b):
py mtk w boot_a,vbmeta_a boot_a.bin,vbmeta.img.empty
py mtk w boot_b,vbmeta_b boot_b.bin,vbmeta.img.empty
*LGUP flash utility:
LGUP-FLASH-Utility (Based on LGUP-1.16-Cmd and LGUP-1.17-LGUP_Common.dll)
Hi, I think that this is my first post, today I received a LG G820TM to flash it, I found a LGUP version at LG G7 forum, cmd based (LGUP_Cmd.exe), so I managed to prepare something to work with, using a batch file, this gave me some problem with...
forum.xda-developers.com
try to install a twrp custom recovery, please!
guys,, someone already tried to install a gsi, by, mtkclient?
I tried, installing the avoc, on the partition system_ but the loop, extranho, if ma gsi has all the apps to start, q missing something I'm not seeing?
Mod edit - translated by https://www.deepl.com/translator:
Guys, it is possible to install a gsi in lgk41s, but when you install it asks for a password!
******************************
{Mod edit: Link removed}
alexandre-2717 said:
Mod edit - translated by https://www.deepl.com/translator:
Guys, it is possible to install a gsi in lgk41s, but when you install it asks for a password! If anyone wants to help or know more, has a group on telegram!
******************************
Pessoal, é possivel instalar uma gsi no lgk41s, mas quando instala ela pede uma senha! Se alguem quiser ajudar ou saber mais, tem um grupo no telegram!
{Mod edit: Link removed}
Click to expand...
Click to collapse
@alexandre-2717
1. As courtesy, I've translated your above post. With reference to rule no. 4 of the XDA Forum Rules, please post in English or add at least an English translation to your Portuguese posts. Thanks for your cooperation!
Spoiler: Rule No. 4
4. Use the English language.
We understand that with all the different nationalities, not everyone speaks English well, but please try. If you're really unable to post in English, use an online translator. You're free to include your original message in your own language, below the English translation. (This rule covers your posts, profile entries and signature). You could try :- https://translate.google.com/ or https://www.babelfish.com/ or use one of your choice.
2. I've removed the reference to Telegram from your above post. As an exemption from the last bullet of rule no. 5 of the XDA Forum Rules, we grant only developers the privilege to share references to their social media in their own development threads. These conditions obviously don't apply to your thread or you.
Regards
Oswald Boelcke
Senior Moderator
hello everyone, could someone tell me, if it's possible to delete certain files, with some mtkclient command, like locksettings.db which is in data/system/ please , and would I also like to shoot zip files? flesheei a gsi, and i'm stuck in the enter you password to start android screen, if i format py mtk and data, it's loop,
@Oswald Boelcke
thank you and sorry rss
{Mod edit: Quotation fixed}
Slim K said:
como uma ferramenta funciona primeiro e v
Click to expand...
Click to collapse
Rickpad said:
Thx for this guide! my backup phone k41s is finally rooted
Click to expand...
Click to collapse
Does anyone know if it's possible to do this on android 9, on 10 I can, but on 9 no, I wanted to because on android 9 there's recovery even if it's stock, is this a serto development site? does anyone know what prevents?
Great method, not that hard (Although not easy either)
Be aware that you first press the assistant + volume down button and then connect the USB to your PC, not the other way around. I didn't realize this earlier and almost pulled my hair out trying to understand why the program was freezing and sending errors
Also, the bootloader unlock command is outdated now, it was changed to py mtk da seccfg unlock
Worked on single-sim version (LM-K410HM)
Does it work on LG k52?
BRAIAN058 said:
Does it work on LG k52?
Click to expand...
Click to collapse
It's mediatek CPU, probably works, wouldn't hurt to try
[email protected] said:
hello everyone, could someone tell me, if it's possible to delete certain files, with some mtkclient command, like locksettings.db which is in data/system/ please , and would I also like to shoot zip files? flesheei a gsi, and i'm stuck in the enter you password to start android screen, if i format py mtk and data, it's loop,View attachment 5492953
Click to expand...
Click to collapse
does anyone know how to remove Vbmeta verification via MTKCLIENt?