Database Info

Install TWRP / ROM on umidigi power

Hello,
I try to install TWRP/ROM on my phone (umidigi power)
questions 1 steps (TWRP):
1. Install Official ROM.
2. enable USB debug
3. enable OEM unlocking
4. adb reboot bootloader
5. fastboot --disable-verity --disable-verification flash vbmeta vbmeta_stockROM.img
6. fastboot --disable-verity --disable-verification flash recovery recovery.img
But Only black screen and nothing happen
questions 2 steps (ROM):
1. Install Official ROM.
2. enable USB debug
3. enable OEM unlocking
4. adb reboot bootloader
5. fastboot erase system
6. fastboot erase cache
7. fastboot --disable-verity --disable-verification flash vbmeta vbmeta_stockROM.img
8. fastboot --disable-verity --disable-verification flash vendor vendor_stockROM.img
9. fastboot --disable-verity --disable-verification flash system system-roar-arm64-ab-floss.img
But i can see system boot logo but just stuck in logo
Can you help me out?
Thanks for your time

some one?

I fixed the questions 1:
i downgrade to old version: UMIDIGI_Power_V1.4_20190611
And now TWRP works.
But still questions 2 back,
stuck on loading logo

How To Guide Restore OnePlus 9 to Stock via Fastboot Commands

This guide assumes you have the SDK Platform Tools installed and working, along with USB drivers for your device (if needed), and have your full update zip which you've already extracted the payload.bin from, and then dumped the images using payload dumper. If you haven't done any of these things yet, there are plenty of other guides out there on how to do them.
Steps:
1. Reboot your device to the bootloader (power off, then hold volume up + power) and connect it to USB.
2. The following command will wipe your device. I found this to be necessary to recover my OnePlus 9:
Code:
fastboot -w
3. Now flash the following files:
Code:
fastboot flash boot boot.img
fastboot flash cpucp cpucp.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash oplusstanvbk oplusstanvbk.img
fastboot flash oplus_sec oplus_sec.img
fastboot flash qweslicstore qweslicstore.img
fastboot flash shrm shrm.img
fastboot flash splash splash.img
fastboot flash vbmeta vbmeta.img
fastboot flash vbmeta_vendor vbmeta_vendor.img
fastboot flash vbmeta_system vbmeta_system.img
fastboot flash vendor_boot vendor_boot.img
fastboot flash vm-bootsys vm-bootsys.img
4. Now reboot into userspace fastboot, aka fastbootd. If you don't do this, the remaining files cannot be flashed:
Code:
fastboot reboot fastboot
5. Flash the remaining files:
Code:
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash qupfw qupfw.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash product product.img
fastboot flash system system.img
fastboot flash system_ext system_ext.img
fastboot flash vendor vendor.img
fastboot flash odm odm.img
6. Final reboot:
Code:
fastboot reboot
7. If everything worked your phone should now boot into OxygenOS.
Note:
The files will be flashed to your currently active boot slot. If any of them fail to flash, switch to the other slot and start over from the beginning. I wasn't able to flash odm, product, system, system_ext and vendor to slot a, and had to use slot b instead. To check current slot:
Code:
fastboot getvar current-slot
To switch slots:
Code:
fastboot --set-active=a
or
Code:
fastboot --set-active=b
Use this guide at your own risk. I take no responsibility if you brick your device, set it on fire, or otherwise mess it up as a result of any of the above steps. That being said, it worked for me using 11.2.2.2.LE25AA available from the official OnePlus support website.

If you want, you can do the flashing easily with powershell, rather than running each command one after the other. Here is what I did:
1. Have fastboot.exe in your path, or in the same folder as all your extracted images. Open powershell and navigate to the folder with your boot images. Connect your phone to USB.
2. This will wipe your device! Reboot to the bootloader and run:
Code:
fastboot -w
3. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'boot|cpucp|dtbo|modem|oplusstanvbk|oplus_sec|qweslicstore|shrm|splash|vbmeta|vbmeta_vendor|vbmeta_system|vendor_boot|vm-bootsys'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
4. Run:
Code:
fastboot reboot fastboot
5. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'abl|aop|bluetooth|devcfg|dsp|featenabler|hyp|imagefv|keymaster|multiimgoem|qupfw|tz|uefisecapp|xbl|xbl_config|product|system|system_ext|vendor|odm'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
6. Run:
Code:
fastboot reboot
7. Proceed to boot normally.
The commands in steps 3 and 5 get a list of all files in the current directory with the .img extension, filter them to the correct ones to flash, and then flash them one after another.
If someone wants, I can probably throw together a script to run the whole process start to finish.
Edit: script attached. I've (unfortunately) had the opportunity to test it and fix all the bugs. So it works. You will need to have fastboot.exe accessible in your system PATH to run it.

Slikkster2k said:
If you want, you can do the flashing easily with powershell, rather than running each command one after the other. Here is what I did:
1. Have fastboot.exe in your path, or in the same folder as all your extracted images. Open powershell and navigate to the folder with your boot images. Connect your phone to USB.
2. Reboot to the bootloader and run:
Code:
fastboot -w
This will wipe your device!
3. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'boot|cpucp|dtbo|modem|oplusstanvbk|oplus_sec|qweslicstore|shrm|splash|vbmeta|vbmeta_vendor|vbmeta_system|vendor_boot|vm-bootsys'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
4. Run:
Code:
fastboot reboot fastboot
5. Run:
Code:
gci -filter *.img | where {$_.Name.split('.')[0] -match 'abl|aop|bluetooth|devcfg|dsp|featenabler|hyp|imagefv|keymaster|multiimgoem|qupfw|tz|uefisecapp|xbl|xbl_config|product|system|system_ext|vendor|odm'} | foreach-object { fastboot.exe flash $($_.Name.split('.')[0]) $_.Name }
6. Run:
Code:
fastboot reboot bootloader
7. Proceed to boot normally.
The commands in steps 3 and 5 get a list of all files in the current directory with the .img extension, filter them to the correct ones to flash, and then flash them one after another.
If someone wants, I can probably throw together a script to run the whole process start to finish.
Click to expand...
Click to collapse
That would be helpful indeed. Would this script run on mac as well?

Not unless there's a version of PowerShell for macs (there is for Linux, but I don't know if it's compatible).

@Slikkster2k: I tried your tutorial. At first it did not work...serveral errors occure during copying one file. On the second run I had to change the slot, than it runs through.
But now I am in a boot loop, during starting the oxygen.
While wiping I got this message:
Code:
fastboot: error: Cannot generate image for userdata
Which version of the OS did you use?
I tried to install the actual european rom (11.2.3.3) on my indian device from china but this obviously did not work. Do you have any suggestions for me?

AxelM said:
@Slikkster2k: I tried your tutorial. At first it did not work...serveral errors occure during copying one file. On the second run I had to change the slot, than it runs through.
But now I am in a boot loop, during starting the oxygen.
While wiping I got this message:
Code:
fastboot: error: Cannot generate image for userdata
Which version of the OS did you use?
I tried to install the actual european rom (11.2.3.3) on my indian device from china but this obviously did not work. Do you have any suggestions for me?
Click to expand...
Click to collapse
I used 11.2.2.2.LE25AA as I said in the original post (this is the global variant, which matches my device). I am not sure if this works for cross-flashing, or if it's possible to cross-flash an Indian phone to EU. Have you tried restoring the Indian ROM? Does that work?
You're getting an actual boot loop? The error I was getting (and the reason I had to restore) was the phone booting to the bootloader or fastbootd (depending on the slot I tried) instead of Oxygen, because it couldn't mount the user partition due to encryption. In fastbootd an error was reported (I forget the exact one) which made me suspect it was a partition mounting issue. At no point was my phone actually boot looping, even during partial/failed flashes.
I've never encountered the error with fastboot -w, but I only did that on my phone once. From some searching online, it can be caused by an old version of the platform tools, so did you download the latest version?

@Slikkster2k: First of all, thank you for providing help
In deed, what worked was the indian first version. This i could flash and from there on everything works. Up to OS and than installing the latest european os. Now everything ist fine...
The error while whiping did not occure while using the indian version...so no clue why...
But now it works for me, thank you!

AxelM said:
@Slikkster2k: First of all, thank you for providing help
In deed, what worked was the indian first version. This i could flash and from there on everything works. Up to OS and than installing the latest european os. Now everything ist fine...
The error while whiping did not occure while using the indian version...so no clue why...
But now it works for me, thank you!
Click to expand...
Click to collapse
Glad to hear you got it working!

PowerShell script added to second post. Totally untested, but I tried to make it as idiot proof as possible.

Slikkster2k said:
This guide assumes you have the SDK Platform Tools installed and working, along with USB drivers for your device (if needed), and have your full update zip which you've already extracted the payload.bin from, and then dumped the images using payload dumper. If you haven't done any of these things yet, there are plenty of other guides out there on how to do them.
Steps:
1. Reboot your device to the bootloader (power off, hold volume up + power) and connect it to USB.
2. The following command will wipe your device. I found this to be necessary to recover my OnePlus 9:
Code:
fastboot -w
3. Now flash the following files:
Code:
fastboot flash boot boot.img
fastboot flash cpucp cpucp.img
fastboot flash dtbo dtbo.img
fastboot flash modem modem.img
fastboot flash oplusstanvbk oplusstanvbk.img
fastboot flash oplus_sec oplus_sec.img
fastboot flash qweslicstore qweslicstore.img
fastboot flash shrm shrm.img
fastboot flash splash splash.img
fastboot flash vbmeta vbmeta.img
fastboot flash vbmeta_vendor vbmeta_vendor.img
fastboot flash vbmeta_system vbmeta_system.img
fastboot flash vendor_boot vendor_boot.img
fastboot flash vm-bootsys vm-bootsys.img
4. Now reboot into userspace fastboot, aka fastbootd. If you don't do this, the remaining files cannot be flashed:
Code:
fastboot reboot fastboot
5. Flash the remaining files:
Code:
fastboot flash abl abl.img
fastboot flash aop aop.img
fastboot flash bluetooth bluetooth.img
fastboot flash devcfg devcfg.img
fastboot flash dsp dsp.img
fastboot flash featenabler featenabler.img
fastboot flash hyp hyp.img
fastboot flash imagefv imagefv.img
fastboot flash keymaster keymaster.img
fastboot flash multiimgoem multiimgoem.img
fastboot flash qupfw qupfw.img
fastboot flash tz tz.img
fastboot flash uefisecapp uefisecapp.img
fastboot flash xbl xbl.img
fastboot flash xbl_config xbl_config.img
fastboot flash product product.img
fastboot flash system system.img
fastboot flash system_ext system_ext.img
fastboot flash vendor vendor.img
fastboot flash odm odm.img
6. Reboot back into the bootloader:
Code:
fastboot reboot bootloader
7. You should now be able to continue booting normally by pressing the power button.
Note:
The files will be flashed to your currently active boot slot. If any of them fail to flash, switch to the other slot and start over from the beginning. I wasn't able to flash odm, product, system, system_ext and vendor to slot a, and had to use slot b instead. To switch slots:
Code:
fastboot --set-active=a
or
Code:
fastboot --set-active=b
Use this guide at your own risk. I take no responsibility if you brick your device, set it on fire, or otherwise mess it up as a result of any of the above steps. That being said, it worked for me using 11.2.2.2.LE25AA available from the official OnePlus support website.
Click to expand...
Click to collapse
My phone has been weird for a week or so occasionally freezing up and saying system ui has crashed or something so I followed these instructions last night to completely wipe and reset everything (after backing up). It worked perfectly!
My only suggestion would be for step 7 to be:
fastboot reboot
Since we're already using fastboot it's just quicker and less fiddly than using the power button

toyanucci said:
That would be helpful indeed. Would this script run on mac as well?
Click to expand...
Click to collapse
Windows offered now to add to MAC - https://support.apple.com/en-us/HT201468

toyanucci said:
My phone has been weird for a week or so occasionally freezing up and saying system ui has crashed or something so I followed these instructions last night to completely wipe and reset everything (after backing up). It worked perfectly!
My only suggestion would be for step 7 to be:
fastboot reboot
Since we're already using fastboot it's just quicker and less fiddly than using the power button
Click to expand...
Click to collapse
Thanks, updated OP.

ok i kind of bricked my phone using this and i need a little help PLEASE?
Ok i tried the fist 2 steps 1. fastboot -w than the first list of commands using cmd with admin rights it worked...i think but it did load everything without issues...now i go to do the "fastboot reboot fastboot"
and now my phone is stuck on a black screen with nothing and i just hear the chime windows makes when you disconnect and reconnect a device..... and in the Device manager this comes up for 10 seconds than goes away for 5 than comes back NON STOP
i cant adb i cant do anything please help !

I'm not sure if this will help you, but I had a lot of issues initially running this. First off you need to use the Oneplus drivers, I don't think the qualcom driver will work the same way. I could be wrong, but that's what I did. Secondly, you need to force install the driver because Windows doesn't like it.
Here are the steps I took.
1. Uninstall any old drivers.
2. Install the newest Oneplus Drivers from here https://oneplususbdrivers.com/
3. Extract the zip file and run the installer like normal
4. Once the installer finishes, you'll need to reboot your machine and bring up the Startup settings (hold down shift and reboot (keep holding down shift until you get a screen with options)) Then click advanced and startup settings and hit restart after that. Once the machines starts up, on the first boot you will have a bunch of options. Choose option 7 "disabling driver signature enforcement" mode.
5. Once Windows launches and you login, go back into the device manager and follow these steps:
right click the device --> update driver
Browse my computer for drivers
Let me pick from a list of available drivers on my computer
Show all Devices --> Next
Have Disk (Button)
Navigate to where you installed Oneplus drivers (Default: C:\Program Files (x86)\OnePlus USB Drivers)
Select "OnePlus_android_winusb.inf"
Select "Oneplus Android Bootloader Interface" and then just hit next/OK until it installs.
You might need to reboot after doing the above, but this worked for me.
----------------------------------------
The above should get your drivers working properly in all modes (adb, fastbootd, bootloader, normal)
One other issue that I ran into when I was using the powershell script was that I was seeing intermittent errors. After trial and error I realized that Windows was picking up a different version of fastboot. I was initially using the minimal adb/fastboot files, but if you compare those to the ones listed in the first post in the "SDK Platform Tools", they are very different from each other, so you need to make sure you use the SDK Platform Tools version. The minimal ADB/Fastboot version will NOT work.
After I got those 2 things ironed out, the powershell script ran without a hiccup and my phone is stock and booting without an issue.
I know I'm late to respond to this thread, but I hope someone finds this information helpful!

Mine keeps trying this and it isn't running and or rebooting into Fastbootd when the script is ran. Should I just try and invoke this manually? I've tried that as well an I'm seeming to get errors left and right with no resolve.

I'd say try it manually and see where the errors happen. Does it boot into fastbootd at all?

Good work

toyanucci said:
I'd say try it manually and see where the errors happen. Does it boot into fastbootd at all?
Click to expand...
Click to collapse
Actually, I ended up making my phone hard bricked to the point where it doesn’t even turn on at this point. I’m just going to send it in for repair, which is nothing short of being due to my stupidity.

ilikepie___ said:
Actually, I ended up making my phone hard bricked to the point where it doesn’t even turn on at this point. I’m just going to send it in for repair, which is nothing short of being due to my stupidity.
Click to expand...
Click to collapse
It's probably stuck in edl mode. Nothing on the screen, no vibration or anything but it shows up in device manager when connected to a computer?
Try the man tool mentioned Here that worked for me.

toyanucci said:
It's probably stuck in edl mode. Nothing on the screen, no vibration or anything but it shows up in device manager when connected to a computer?
Try the man tool mentioned Here that worked for me.
Click to expand...
Click to collapse
I’ll give it a shot, yeah it doesn’t do anything. Can’t see a display or anything on the screen.

[Tutorial ]IIIF150 R2022 Bootloader + Root

bootloader unlock
WARNING! THIS WILL VOID YOUR WARRANTY! IF YOU DO NOT KNOW WHAT THIS DOES LEAVE! THERE IS ALMOST NO SUPPORT FOR THIS DEVICE!
go to developer options and turn on oem unlocking
reboot to fastboot
Windows sucks for this because the drivers that you can find will not work!
install linux or in a vm
install fastboot and adb on linux
fastboot command: fastboot reboot bootloader
fastboot command: fastboot flashing unlock
reboot the phone.
you get a "orange" warning device will reboot it self.
done!
Root:
Hello welcome to this root tutorial of the IIIF150 R2022!
WARNING YOU WILL VOID YOUR WARRENTY!
UNLOCK THE BOOTLOADER FIRST!
EASY WAY NOT RECOMMENDED!
1. https://easyupload.io/0e0o5e MAGISK BOOT IMAGE
2. flash magisk boot image with fastboot
3. reboot phone
I DO NOT RECOMMENDED THIS! WHY WOULD YOU TRUST ME? IF YOU TRUST ME DO THE EASY WAY OTHERWISE DO IT YOURSELF!
NORMAL:
1. first download the STOCK os: https://firmwarefile.com/iiif150-r2022
2. download magisk on your device.
3. copy boot.img to your device.
4. follow the steps on magisk. choose the boot.img and let it patch.
5. put the file on your LINUX pc (windows is possible but it sucks because again drivers)
6. put your device in fastboot mode! NOT FASTBOOTD
7. on pc type: fastboot flash boot magiskbootimgname.img
8. YOUR NOT DONE!!!!!!!!!!
--------------
1. type these commands:
fastboot --disable-verity --disable-verification flash vbmeta (vbmeta file name you have download with the stock rom) click enter
fastboot --disable-verity --disable-verification flash vbmeta_system (vbmeta_system file name you have download with the stock rom) click enter
fastboot --disable-verity --disable-verification flash vbmeta_vendor vbmeta_vendor.img (vbmeta_vendor file name you have download with the stock rom) click enter
---------------------------------------------
YOUR NOW DONE.
IT IS POSSIBLE THAT IT DOES NOT WORK THE FIRST TIME IF IT IS STUCK ON BOOTING REFLASH MAGISK BOOT IMG

I've been waiting for this tutorial since November 2021, although I still have some doubts I'll try to do it.

Hello Any chace to have root tutoriel for IIIF150 B2021 ?

thibbea said:
Hello Any chace to have root tutoriel for IIIF150 B2021 ?
Click to expand...
Click to collapse
Use Magisk flash boot img with magisk

Question Regarding magisk/custom ROM

Hello all,
I rooted & unlocked my TMO OP9 using magisk and flashed a stock image.
I'm now trying to install a A13 mod from Pixel Experience. I patched the boot image after running the payload dumper tool. Now I have the patched boot image from magisk copied to my PC. I"m not sure what commands to run now once I reboot into fastboot. Maybe I'm not in the right fastboot (like fastbootd or something)
PS C:\Users\cterr\OneDrive\Desktop\OnePlus9-December2022> adb devices -l
List of devices attached
6bf0a351 device product:OnePlus9 model:LE2117 device:OnePlus9
PS C:\Users\cterr\OneDrive\Desktop\OnePlus9-December2022> adb reboot fastboot
<reboots>
<select fastboot from menu, reboots>
PS C:\Users\cterr\OneDrive\Desktop\OnePlus9-December2022> .\fastboot.exe flash boot .\magisk_patched-25200_aAy2x.img
< waiting for any device >
This fails as fastboot doesn't see my phone. I'm not even sure if I'm supposed to flash to <boot> or recovery.
I remember running this command below for disable-verity in the past but it fails as well. Probably due to a typo. If anyone can confirm that would be great. Do I use fastboot to flash to the boot? Like #fastboot flash boot <magisk_image>. I'm nervous that once I get the fastboot to flash i'll flash it to the wrong place.
PS C:\Users\cterr\OneDrive\Desktop\OnePlus9-December2022> fastboot flash vbmeta --disable-verity --disable-verification vbmeta.img
C:\Android\fastboot.exe: unknown option -- disable-verity
Thanks!

How To Guide How to Flash GSI on Moto g62 5g

Download your GSI image. (if u want gapps install pixelexperience)
Download platform tools i attached
Unlock bootloader (If you have unlocked bootloader skip this step.). guide how to unlock bootloader here https://motorola-global-portal.custhelp.com/app/standalone/bootloader/unlock-your-device-a/
After unlocking bootloader we can go to installing our GSI.
Boot to bootloader. to boot to bootloader turn off phone and press volume down + power button
After doing that you need to boot to fastbootd write "fastboot reboot fastboot" in platform tools
If there is a screen with bold red text written "fastbootd" we can go to erasing data and system partitions.
now u need to Flash vbmeta.img : "fastboot --disable-verification flash vbmeta vbmeta.img" and wait until it says OK
If we did that we can erase system partition by typing in fastboot "fastboot erase system" If it says OK we can go to the next step
If we get "CANNOT RESIZE SYSTEM PARTITION" do this: "fastboot delete-logical-partition product_a" and "fastboot delete-logical-partition product_b"
Now it's time to flash our GSI. To do that just type "fastboot --u flash system *name of your gsi*.img
And wait until it flashes and !!!!DO NOT REBOOT!!!!!
After successful flash we need to type "fastboot -w" and then go to recovery do factory data reset
And now you can reboot.
if u don't know what rom to install this rom linked here https://drive.google.com/file/d/1UsCY-gsn3rU4JpefOMMoIMzYdC-rsr_K/view?usp=sharing is 100% working list of other roms for this phone is here https://forum.xda-developers.com/t/...g-gsis-for-moto-g62-5g.4600029/#post-88688661
(The files i meant like vbmeta and platform tools are attached to thread)