Database Info

How to update OOS 5.1.6, Install official TWRP and magisk - tested working!

Hi guys,
Here is my complete foolproof guide on how to update your system. Please note that there may be other maybe easier ways that cut-out some steps but this worked for me. It is intended for Noobies so I apologise to more advanced users if it seems tedious and long-winded. But that's how Noobies like it with everything explained in detail.
IMPORTANT NOTE: If you have previously used parallel apps then before doing any of this process you must delete user 999 from the system, otherwise you backups will not work!!!
From a terminal window (I use terminal emulator from play store ) type su and enter. Now type the command pm remove-user 999 and enter. Now you shouldn't have to worry about parallel apps messing up your backups.
Thanks to @dgunn for this :good:
https://forum.xda-developers.com/on...estore-999-t3801632/post76760812#post76760812
Also, please note that I have NEVER previously installed an un-official twrp on my device (wanted to wait for official ), however, I was unlocked, and rooted with magisk v16.0 and on stock oos 5.1.5 before beginning this upgrade process.
If you already have an un-official twrp installed, then I cannot guarantee that this guide will work for you. It might, it might not
Disclaimer: This is a guide for helping others. It is your choice to follow it and I take no responsibility for any problems you encounter as a result of following this guide. You do it at your own risk
Ok, lets get started......................
Actually, before we do let's get one thing clear that is confusing a lot of people regarding fastboot and twrp. There are 2 ways of putting twrp recovery onto your phone. A temporary way (disappears after rebooting and goes back to stock recovery) and a permanent way (the best way that stays put - what we all want right?). This guide assumes that you don't currently have twrp on your phone.
In order to put a permanent official twrp on your phone, first we have to boot (NOT flash!) into a temporary version of twrp. The fastboot command for this is "fastboot boot path_to_temporary_twrp.img" (without the quotes of course )
The difference between temporary twrp and permanent twrp is in whether we either fastboot boot or fastboot flash.
Ok, let's begin
First of all, as a precaution, disable all security on your device like pin, pattern, password, fingerprint. Make sure that when you wake your phone it goes straight to the homescreen without any prompts for pins etc etc. May not be needed but it's what I did
1. Download the following files to the following locations....
a. Official oxygen OS 5.1.6 zip file (full zip) > to root of sdcard .
b. Official twrp installer ZIP file > to root of sdcard. (This is our permanent twrp file)
c. Magisk root zip file (I used v 16.0 but v16.4 zip file should be okay too) > to root of sdcard.
d. Official twrp installer IMG file > to your PC in the same folder as your fastboot files. (This is our temporary twrp file)
These files are available for download in other threads on XDA just search for them.
Once that is done proceed as follows.....
2. Go to settings>system updates and click the gear icon in the top right and choose "local upgrade" and then select the Oxygen 5.1.6 zip file from your sdcard. The system will now begin to update itself. Once finished it will prompt you to reboot, do this, and the system will boot back up into Oxygen OS 5.1.6 :good:
3. Now, long press your power button and select reboot and select bootloader option and your phone will reboot into bootloader (fastboot) mode.
4. On your PC go to your fastboot folder and open a command prompt in that folder (don't forget you previously put the temporary twrp image file in here)
5. Now plug your phone into the PC
6. At the command prompt enter following command fastboot devices
and your phone should show up as connected and recognised.
7. We are now going to boot the phone into the temporary twrp. Type the following command fastboot boot <name of temporary twrp file (from your fastboot folder)>.img
8. Your phone will now boot into the temporary twrp recovery and from here we can now flash the permanent version of twrp that we previously put on our sdcard.
9. On your phone, select Install, then find the twrp zip file on the root of your sdcard, select it and swipe to flash.
10. Once this has flashed successfully, we now need to reboot into this new permanent recovery. DO NOT REBOOT TO SYSTEM AT THIS POINT! Now, select "Reboot" option and select "Recovery". Your phone will now reboot into the new permanent twrp. You can now forget about the other temporary twrp from earlier
11. Once the phone goes back into recovery select Install option and find the Magisk root zip file on your sdcard and select it. Now swipe to flash it. After successfully flashing Magisk, you are now ready to enjoy the fruits of your labours
Go back to the twrp homepage and select Reboot>system.
The system will now boot normally and if you have followed these steps to a Tee you will be on OOS 5.1.6 and rooted!
I have also done a successful twrp backup without any error messages. Your previous data will be untouched and you can now set-up your security again.
One final thing to note - because the boot and recovery partitions are now combined, this means that everytime you flash something to your boot partition, your new permanent twrp recovery will be lost and you will have to re-install twrp again from scratch initially through fastboot.
Enjoy

carlos67 said:
From a terminal window (I use terminal emulator from play store ) type su and enter. Now type the command pm remove_user 999 and enter. Now you shouldn't have to worry about parallel apps messing up your backups.
Click to expand...
Click to collapse
I bet the terminal command should be:
pm remove-user 999

I've made almost the same without problem

After many years of being actively involved in unlocking, flashing, and tinkering. I feel I'm starting from scratch. This quick guide is exactly what I've been waiting for as I'm in the same situation with being simply unlocked and rooted lol. I'll be replicating these steps shortly ?.
Only thing I'm wondering, once everything is done and running... If I flash a rom with the official "permanent" twrp, it's gone gone? Let's just say, renovate ice ROM?
Maybe it's the 16 hour day I worked and lack of sleep... But having it replaced upon a single rom flash and carrying the name "permanent" seems like 2 opposing ideas lol

Kiddman said:
I bet the terminal command should be:
pm remove-user 999
Click to expand...
Click to collapse
Yes, well spotted and corrected :good:
InflatedTitan said:
After many years of being actively involved in unlocking, flashing, and tinkering. I feel I'm starting from scratch. This quick guide is exactly what I've been waiting for as I'm in the same situation with being simply unlocked and rooted lol. I'll be replicating these steps shortly ?.
Only thing I'm wondering, once everything is done and running... If I flash a rom with the official "permanent" twrp, it's gone gone? Let's just say, renovate ice ROM?
Maybe it's the 16 hour day I worked and lack of sleep... But having it replaced upon a single rom flash and carrying the name "permanent" seems like 2 opposing ideas lol
Click to expand...
Click to collapse
If you were to flash a full OTA official update then yes, your "permanent" twrp will be gone because the boot partition gets flashed to stock and you'd need to re-install twrp starting in fastboot. However, for custom rom flashes, it depends if their is a kernel bundled in with the rom. If not then twrp should remain, if yes then as with official update, re-install twrp.
It's more normal for a custom rom to simply overwrite system partition without touching boot partition and twrp, but, sometimes custom rom's like Renovate come bundled with a kernel (TBalden's) and wipe out twrp.
If I'm wrong on this I stand to be corrected.

Kiddman said:
I bet the terminal command should be:
pm remove-user 999
Click to expand...
Click to collapse
Yes you are correct because this was my finding and thank you OP for not giving credit
My findings of the 255 error (999)
https://forum.xda-developers.com/oneplus-6/how-to/255-error-twrp-backup-restore-999-t3801632

dgunn said:
Yes you are correct because this was my finding and thank you OP for not giving credit
My findings of the 255 error (999)
https://forum.xda-developers.com/oneplus-6/how-to/255-error-twrp-backup-restore-999-t3801632
Click to expand...
Click to collapse
My apologies, an oversight, corrected

carlos67 said:
My apologies, an oversight, corrected
Click to expand...
Click to collapse
Thank you sir. And great write up btw

Something to note is the Renovate ICE 1.0 magisk module messed with the text in settings on OOS 5.1.6. It went back to normal when I disabled that module.
I thought it was the VoEnabler module initially but I wasnt correct.

I put the zip in the root folder (Not the actual folder named root) but the local upgrade isn't showing anything in there.
I'm on 5.1.5 rooted with Magisk 16.0 and have 5.7 magisk manager installed along with xposed and gravity box.
Any idea why my local upgrade isn't detecting the upgrade zip? I downloaded it from Funk Wizards post. I got clicked the "official" link for OOS 5.1.6

I have a custom kernel and magisk installed, can I still follow this guide?

surface13 said:
I put the zip in the root folder (Not the actual folder named root) but the local upgrade isn't showing anything in there.
I'm on 5.1.5 rooted with Magisk 16.0 and have 5.7 magisk manager installed along with xposed and gravity box.
Any idea why my local upgrade isn't detecting the upgrade zip? I downloaded it from Funk Wizards post. I got clicked the "official" link for OOS 5.1.6
Click to expand...
Click to collapse
Figured it out, it was because the ro.product.device=OnePlus 6 instead of OnePlus6 in the build.prop file.
I had originally changed it to sailfish to see if I can get Daydream working. When I changed it back I accidentally added a space =/

Anyone done this on a phone with unofficial TWRP to start out yet?

Lownita said:
I have a custom kernel and magisk installed, can I still follow this guide?
Click to expand...
Click to collapse
Yes you can.

Considering that many of us have been rooted with patched boot image and no custom recovery, this guide is very well written.

Simple Guide is Already available | No Root | No Rom
youtube.com/watch?v=a7rh4NpYD7E
I followed the above youtube guide . Very simple .
Steps :
Install VPN app like Surf Easy Android VPN
Change Region to Canada or Germany
Again try to update the Oxygen OS
It will show in update available .

"
2. Go to settings>system updates and click the gear icon in the top right and choose "local upgrade" and then select the Oxygen 5.1.6 zip file from your sdcard. The system will now begin to update itself. Once finished it will prompt you to reboot, do this, and the system will boot back up into Oxygen OS 5.1.6
"
After that I got constant reboot with the message " System UI has stopped"

x111 said:
"
2. Go to settings>system updates and click the gear icon in the top right and choose "local upgrade" and then select the Oxygen 5.1.6 zip file from your sdcard. The system will now begin to update itself. Once finished it will prompt you to reboot, do this, and the system will boot back up into Oxygen OS 5.1.6
"
After that I got constant reboot with the message " System UI has stopped"
Click to expand...
Click to collapse
Could be a corrupt download file. I suggest you do the following.....
Re-download the file and check it's good using an MD5 checker app/tool. Then, boot your phone into bootloader (fastboot) mode by powering off first and then pressing and holding the vol up button.
Then follow steps 4-to-10 in my guide for installing (1st) temporary twrp and then (2nd) permanent twrp. Once you have permanent twrp and are booted into it you should then copy the "new" download zip for the OTA that you md5 checked from your PC onto the root of your sdcard and install it by flashing the zip file in twrp. Now you should reboot to system which will change the active slot to the updated OOS you just flashed and then if you want boot back into recovery to flash a custom kernel (if you so wish) and Magisk root zip (again if you so wish).

carlos67 said:
Could be a corrupt download file. I suggest you do the following.....
Re-download the file and check it's good using an MD5 checker app/tool. Then, boot your phone into bootloader (fastboot) mode by powering off first and then pressing and holding the vol up button.
Then follow steps 4-to-10 in my guide for installing (1st) temporary twrp and then (2nd) permanent twrp. Once you have permanent twrp and are booted into it you should then copy the "new" download zip for the OTA that you md5 checked from your PC onto the root of your sdcard and install it by flashing the zip file in twrp. Now you should reboot to system which will change the active slot to the updated OOS you just flashed and then if you want boot back into recovery to flash a custom kernel (if you so wish) and Magisk root zip (again if you so wish).
Click to expand...
Click to collapse
Thanks for response.
https://forum.xda-developers.com/showpost.php?p=76773727&postcount=153

Followed the procedure: Installed EX Kernel as well. Now I'm getting a popup message after every reboot: There's an internal problem with your device. Contact your manufacturer for details.
No issues as such but I'm getting this message everytime I reboot. Any suggestions?

[Treble][Pie]A full guide on how to install 9.0 GSI on Razer Phone on both A/B

I found linuxct's guide (Link: https://forum.xda-developers.com/razer-phone/how-to/treble-install-generic-image-gsi-razer-t3770684) need to be modified to get 9.0 GSI working (at least in my circumstance). I haven't tried any Oreo Gsi but to my case, I can't properly booted to 9.0 Gsi by following exactly to this guide. That's why I want to write my own processes of getting it works. Hope it's useful to some of you.
0) I strongly recommend you to flash back to stock image from razer, if you have messed up with the partitions. !!THIS WIPES YOUR DATA, PLEASE BACKUP THE INTERNAL STORAGE!!
Code:
(Link: https://s3.amazonaws.com/cheryl-factory-images/cheryl-o-global-6033.zip)
After flashing to stock, it should automatically reboot into the system.
/*To your convenience, please put all the required file under the adb tool folder*/
1) Enable USB debugging, reboot to bootloader by command:
Code:
adb reboot bootloader
2) Flash the prebuild boot image in linuxct's guide by command:
Code:
fastboot flash boot_a boot_linuxct_20180420_cheryl_omr0.img
(Link is mentioned above)
This boot image has TWRP and Magisk built in.
3) Reboot into TWRP by command:
Code:
fastboot reboot
4) In TWRP, tap Wipe and do a factory wipe. DON'T CHANGE THE DEFAULT WIPE SETTINGS.
5) Flash the GSI you have, then reboot to bootloader.
6) Extract and copy the stock boot image from Razer to the adb tool folder, and flash the boot.img by command:
Code:
fastboot flash boot_a boot.img
7) Reboot to the stock recovery, and do factory wipe, then reboot to bootloader.
This will decrypt the /data. (I am not sure why if I do it under TWRP, I can never boot into system, but that's the case.)
8) Flash the prebuilt image from linuxct again by command:
Code:
fastboot flash boot_a boot_linuxct_20180420_cheryl_omr0.img
9) Reboot to the system by command:
Code:
fastboot reboot
And whola, you should be able to boot into system without any decryption message. And you will have a partially functional TWRP.
If you need to flash any other GSI next time, you should first copy the GSI image through MTP in system. Because the TWRP doesn't support adb command and can't be mounted as MTP.
Once you have copied the GSI image, you can reboot into TWRP and flash image as usual.

Here are the photos proving this works. I flashed Pixel Dust first through the command and booted. Then I reboot into TWRP and flashed PixelExperience through TWRP and get it booted.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Can't image I figured out to flash the second system_b so quickly lol.
0) In system_a, reboot to bootloader by command: adb reboot bootloader
1) Flash the GSI you have to system_b: fastboot flash system_b [The GSI you have]
2) Flash the stock boot image to boot_b: fastboot flash boot_b boot.img
3) Set active partition to B: fastboot --set-active=b
This is where I found linuxct's guide tricky because it should be 'b'.
'_b' doesn't work.
4) Reboot to stock recovery: fastboot reboot
5) Do a factory wipe, then go back to bootloader
6) Flash the prebuilt image to boot_b: fastboot flash boot_b boot_linuxct_20180420_cheryl_omr0.img
7) Reboot to the recovery: fastboot reboot
And it will brings you to TWRP on B partition, and you can reboot to system_b now.
And whola, and now you can have both AB system with different GSI. And you can switch to any partition by going to TWRP on either partition and switch as you like!
Here are the photos proving I have Pixel Experience and Pixel Dust working seperately on two partitions.

I also found that the prebuilt boot image from linuxct is breaking the wifi. Till now, you should have the TWRP patched boot image on both AB partition. So fixing that is pretty straightfoward.
1) Copy the stock boot image and TWRP installer zip to your phone in system.
Link: https://dl.twrp.me/cheryl/
I used the 3.2.1 version.
2) Boot into TWRP by command: adb reboot recovery
3) Flash stock boot.img on both A/B partition.
You can do this by first flash it to Slot A, and switch to B in TWRP. NO NEED TO REBOOT, SIMPLY SWITCH SLOT IN TWRP!!
4) Flash the twrp zip file.
This should fix your wifi.
DON'T FLASH MAGISK! I found flashing even the latest magisk v18.0 breaks wifi again.

So could you have stock on slot a and another GSI on slot b?

Magisk still breaking WiFi and 4g? I played around with 9.0 gsi's ages ago and that was the only thing stopping me from using it. Have anyone tried the latest canary builds of magisk also?

askylitangel said:
So could you have stock on slot a and another GSI on slot b?
Click to expand...
Click to collapse
Since A/B systems are using a common /data partition, I think you can at most flash an 8.1 Oreo on another slot because the stock image is 8.1. And this breaks the OTA of stock, so pretty meaningless.

It worked for me following the guide unfortunately had to go back to stock (no WiFi) shame was looking good too thanks for the guide though helped at least getting system up and booting

parky169 said:
It worked for me following the guide unfortunately had to go back to stock (no WiFi) shame was looking good too thanks for the guide though helped at least getting system up and booting
Click to expand...
Click to collapse
Follow the guide on #4, it will certainly fix Wi-Fi.

Followed must of the guide except just on partition a all worked nice
Thanks a lot.had no issues installing magisk either

Any of these ROMS run at the full 120hz? So far I've tried 3 and the seem to run even lower than 60hz.

BoostRoid said:
Any of these ROMS run at the full 120hz? So far I've tried 3 and the seem to run even lower than 60hz.
Click to expand...
Click to collapse
Pixel Experience, Pixel Dust, Aosp extended 6.1

BoostRoid said:
Any of these ROMS run at the full 120hz? So far I've tried 3 and the seem to run even lower than 60hz.
Click to expand...
Click to collapse
Reboot after first boot fixes it.

parky169 said:
Followed must of the guide except just on partition a all worked nice
Thanks a lot.had no issues installing magisk either
Click to expand...
Click to collapse
To clarify, you only installed on partition A, and installed magisk without breaking wifi?

Apologies for not clearing one thing up,I installed android 8.1 and it all
Worked I didn't realize at first it was android 9 that was having WiFi breaking,I haven't tried that one yet.sorry if I was misleading anyone
With my post.

All I had to do was flash the GSI image via fastboot and that seemed to work fine with no other flashing needed

What gsi ROM did you flash? And have you flashed magisk on it ?.

HO-COOH said:
I also found that the prebuilt boot image from linuxct is breaking the wifi.
Click to expand...
Click to collapse
Using an MR0 image on MR3 is not recommended, and using Magisk will break RIL (data connectivity) and WiFi.
If you want to run Pie GSIs, forget about using Magisk and run phh-su. Lastly, if you want your front camera and Bluetooth A2DP to work, use latest phh-gsi image v109. Using older versions than v108 is discouraged for breaking the mentioned.
Current status:
1. Cheryl specific overlays are not yet merged into phh source code because I'm a lazy assh*le. If you want your device to have Adaptive brightness, gestures, and fix the strong vibration, place the following apk inside /system/overlay or /vendor/overylay
2. Razer Power Service and NFC are faulty and will spam your logcat, which may, in the end, reduce your battery life. You need to extract [email protected] from both /system/lib and /system/lib64 from Razer's stock ROM and place them respectively into /vendor/lib and lib64. I've conveniently extracted them for you (Folder named 32's file should be extracted onto /vendor/lib and folder named 64's file should be extracted onto /vendor/lib64).
To kill NFC until we find a proper solution, go into your GSI's filesystem path /system/app/NfcNci and delete or change NfcNci.apk's filename into anything else, like NfcNci.bak.
3. Common to MSM8998, and I believe several other Qcomm based smartphones, Bluetooth In-Call audio is not working, and audio gets redirected to Earpiece.
4. Everything. Else. Works.
Please thank @phhusson for his amazing job in this project!
---------- Post added at 09:16 ---------- Previous post was at 09:13 ----------
As an extra, if you would like to erase your data/userdata partition without messing up with recoveries, you could just issue the following fastboot command:
Code:
fastboot format:ext4:0xc72dd3000 userdata
Where 0xc72dd3000 is the userdata partition size with FBE enabled.
If you are running a bootimage without FBE, the partition size might be 0xC72DD7000, so the command would be:
Code:
fastboot format:ext4:0xC72DD7000 userdata
--------------------
As a result, a summary of OP would be:
0. Flash latest cheryl fastboot image just like explained in OP.
1. Download the Android 9.0 GSI of your preference.
2. Reboot into fastboot.
3. Wipe your userdata partition with:
Code:
fastboot format:ext4:0xc72dd3000 userdata
4. Flash the system image you downloaded with:
Code:
fastboot flash system IMAGENAME.img
Where IMAGENAME goes your system image name. In our bootloader, you don't need to specify the partition you want to flash, and fastboot flashing into just "system" will flash the current slot.
5. Follow the steps from 1 and 2 from the Current status section above to get all the perks to work.

Tried multiple android 9 GSI roms and some boots but no wifi and data (some don't even boot).
Wifi fix (works on Arrow OS) on post #4 doesn't work. After flashing twrp 3.2.1.0, the phone does not boot on any android 9 GSI roms. Anyway thanks for your work trying to make GSI work on Razer phone.

Hello, I followed your instructions in post 4 to the letter, I've got 4g but no wifi. Any ideas what I'm doing wrong?

[GUIDE][OP7][9.0/10.0/11.0] Unlock Bootloader | TWRP | Root with Magisk | Update

Code:
#include <std_disclaimer.h>
/*
*
* We are not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at us for messing up your device, we will laugh at you.
*
*/
Introduction
This thread is dedicated to newbies and rooting, so if you're familiar with the whole procedure, you're done
Just ask questions about every step and you'll receive help!
Downloads
TWRP Installer ZIP and TWRP IMG for Android 9/10: https://forum.xda-developers.com/oneplus-7/development/recovery-unofficial-twrp-recovery-t3932943
TWRP for Android 11(including instructions, thank's to @Nebrassy ): https://forum.xda-developers.com/t/recovery-11-unofficial-teamwin-recovery-project.4289455/
TWRP Installer ZIP = For example twrp-3.4.0-10-guacamole-unified-installer-mauronofrio.zip
TWRP IMG = For example twrp-3.4.0-10--guacamole-unified-Q-mauronofrio.img
Check for Pie or Q TWRP IMG! If you have Android Pie, choose Pie TWRP IMG, if you have Android Q, choose Q TWRP IMG.
The TWRP Installer ZIP works on Android Pie(9)/Q(10)
Magisk ZIP: https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
Hints
If you need to update TWRP or Magisk, always keep older versions of both in hand(Magisk canary or beta may have issues)
Remove your lockscreen protection which also removes encryption to prebvent mounting issues within TWRP
Before proceeding
Your Windows PC should already recognized your device with the USB cable
Use an USB cable provided with the phone
Make sure your Windows Explorer is set up to have file extensions enabled to avoid file name issues
This process will FORMAT/WIPE/DELETE your internal storage and every file of your phone, so please back it off your device at first!
Also keep a boot.img from your current system in place if anything went wrong so you can flash it via fastboot, see "Rooting without TWRP" for how to get it.
Rooting with TWRP (Android 9/10)​
Steps for unlocked bootloader with TWRP AND Root(Magisk)
1. Follow this guide to unlock your Oneplus 7 bootloader(wipes everything on your device, works for OP7 pro and OP7): https://forum.xda-developers.com/showpost.php?p=79741564&postcount=2.
2. Your phones bootloader is now unlocked, leave the phone plugged to your PC
3. Make sure you have enabled USB-Debugging and Advanced Reboot under developer options(see step 1 how to enable it all) again after the first boot of the wiped device, since this gets reset
4. Copy the latest "TWRP installer ZIP" and "Magisk ZIP" to the phones internal storage.
5. Copy the "TWRP IMG" to the "platform-tools" folder from step 1.
6. Open command window or PowerShell window again if you did not closed it before within the "platform-tools" folder from step 1
7. Type
Code:
adb devices
to see if your device is connected and recognized sucessfully by your PC.
8. Type
Code:
adb reboot bootloader
to reboot to fastboot mode.
9. Type
Code:
fastboot boot recoveryimgfilename.img
to temporary boot TWRP, where recoveryimgfilename.img is the name of your downloaded TWRP *.img file, so watch your file name!.
10. Enter your screen lock PIN within TWRP if you have set it up before.
11. Allow modifications.
12. Now you have temporary booted twrp recovery. To make it stick permanently you need to flash the "TWRP installer ZIP" from your phones storage from step 4.
13. Hit "install" and navigate to the "TWRP installer ZIP" file and select it for installation(dont boot the system now!).
14. Go back and flash "Magisk ZIP" the same way as for TWRP Zip otherwise your device will not boot!
15. Thats all, you can unplug the USB cable and boot the device to your system. Your device is now bootloader unlocked with TWRP and Magisk:highfive:
Steps for unlocked bootloader with TWRP WITHOUT Root(Magisk)
1. Follow this guide to unlock your Oneplus 7 bootloader(wipes everything on your device, works for OP7 pro and OP7): https://forum.xda-developers.com/showpost.php?p=79741564&postcount=2.
2. Your phones bootloader is now unlocked, leave the phone plugged to your PC
3. Make sure you have enabled USB-Debugging and Advanced Reboot under developer options(see step 1 how to enable it all) again after the first boot of the wiped device, since this gets reset
4. Copy the latest "TWRP IMG" to the phones internal storage.
5. Copy the latest "TWRP IMG" to the "platform-tools" folder from step 1.
6. Open command window or PowerShell window again if you did not closed it before within the "platform-tools" folder from step 1
7. Type
Code:
adb devices
to see if your device is connected and recognized sucessfully by your PC.
8. Type
Code:
adb reboot bootloader
to reboot to fastboot mode.
9. Type
Code:
fastboot boot recoveryimgfilename.img
to temporary boot TWRP, where recoveryimgfilename.img is the name of your downloaded TWRP *.img file, so watch your file name!.
10. Enter your screen lock PIN within TWRP if you have set it up before.
11. Allow modifications.
12. Now you have temporary booted twrp recovery. To make it stick permanently you need to flash the "TWRP IMG" from your phones storage from step 4
13. Navigate to advanced menu within TWRP, click on "Install Recovery Ramdisk" and select the "TWRP IMG". This will patch the boot image which does Magisk otherwise.
14. Thats all, you can unplug the USB cable and boot the device to your system. Your device is now bootloader unlocked with TWRP:highfive:
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Rooting without TWRP (Android 9/10/11)​
Also useful to get stock recovery and kernel --> Recovery is within boot.img on A/B devices like OP7
Refer here for unlocking the bootloader.
1. Download the payload dumper tool to your PC from here and extract it
2. Download the FULL OxygenOS Rom zip(The version your phone is running) and extract the payload.bin
3. Put payload.bin to "payload_input" folder o the extracted tool
4. Run payload_dumper.exe from the tool's folder
5. Extracted img files are in "payload_output" folder
6. Now you have your own boot.img for your Rom
7. Copy it to your phone
8. Patch the boot.img with Magisk directly on your device: Magisk Manager App -> hit install after your Magisk version -> hit "Select and Patch a file"
9. Copy the patched boot.img (it should be in the Download folder of your device named something like "magisk_patched-22100_bjjRn.img") back to your PC
10. Reboot your device to fastboot
11. Flash the patched magisk_patched-22100_bjjRn.img
Code:
fastboot flash boot_a magisk_patched-22100_bjjRn.img
fastboot flash boot_b magisk_patched-22100_bjjRn.img
12. Reboot your device. Now you have your phone rooted without the need of TWRP (Check with Magisk Manager App)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Update your rooted OxygenOS (Android 9/10)​Steps for UPDATE OxygenOS via OTA and keep unlocked bootloader, TWRP, Root(Magisk)
1. [OPTIONAL, but highly recommended]Backup everything in case of issues!
2. Go to Magisk Manager App and uninstall all modules
2.1 [Optional]: For some modules(read those instructions) you should do an reboot now, then proceed
3. Go to Android settings -> system -> system update and hit "Download & Install Now", don't reboot yet!
4. (not for Android 11)Flash "TWRP ZIP" within Magisk Manager App like a Module: Magisk Manager App -> Menu -> Modules "+". This installs TWRP to both a/b partitions.
5. Install Magisk via Magisk Manager App again: Magisk Manager App -> hit install after your Magisk version -> hit "install to inactive slot"
6. Reboot your device
7. Reinstall your Magisk Modules(maybe a reboot is necessary)
Your device is now updated via OTA and you keep TWRP and Root:highfive:
Steps for UPDATE OxygenOS via local upgrade and keep unlocked bootloader, TWRP, Root(Magisk)
1. [OPTIONAL, but highly recommended]Backup everything in case of issues!
2. Download the full rom zip file and place it into the root folder of your storage(/storage/emulated/0)
3. Go to Magisk Manager App and uninstall all modules
2.1 [Optional]: For some modules(read those instructions) you should do an reboot now, then proceed
4. Go to Android settings -> system -> system update and hit gear icon top right -> local upgrade, don't reboot yet!
5. (not for Android 11)Flash "TWRP ZIP" within Magisk Manager App like a Module: Magisk Manager App -> Menu -> Modules "+". This installs TWRP to both a/b partitions.
6. Install Magisk via Magisk Manager App again: Magisk Manager App -> hit install after your Magisk version ->hit "install to inactive slot"
7. Reboot your device
8. Reinstall your Magisk Modules(maybe a reboot is necessary)
Your device is now updated via local upgrade and you keep TWRP and Root:highfive:
If you have any issues, just feel free to ask!

@strongst you should maybe write in your guide that magisk flash is a must! Without phone won't boot if it's stock.
There are a lot of people who wanna flash TWRP without magisk. I don't know why they do that it makes no sense for me.

Kollachi said:
@strongst you should maybe write in your guide that magisk flash is a must! Without phone won't boot if it's stock.
There are a lot of people who wanna flash TWRP without magisk. I don't know why they do that it makes no sense for me.
Click to expand...
Click to collapse
I made it a little bit more clear, thanks, that's an common issue across several devices and requested often enough

Thank you for the quick tutorial. For me it looks very similar to the procedure with the OnePlus 5, am I right?
Does this indicate, that an EFS Backup is also to create the same way? https://forum.xda-developers.com/oneplus-5/how-to/oneplus-5-unlock-bootloader-flash-twrp-t3624877
BR
Axel

AxelM said:
Thank you for the quick tutorial. For me it looks very similar to the procedure with the OnePlus 5, am I right?
Does this indicate, that an EFS Backup is also to create the same way? https://forum.xda-developers.com/oneplus-5/how-to/oneplus-5-unlock-bootloader-flash-twrp-t3624877
BR
Axel
Click to expand...
Click to collapse
There's something different after unlocking the bootloader(which is the same). Twrp and magisk installation is different due to treble.
For EFS you can backup with twrp or local terminal
dd if=/dev/block/sdf2 of=/sdcard/modemst1.bin bs=512

Thanks for the guide, my OnePlus 7 came with 9.5.5 and I want to clean flash to the latest 9.5.8. I have already unlocked the bootloader, boot into TWRP and installed TWRP, are these the correct steps to flash 9.5.8 as I'm confused with the A/B partition?
1. Wipe data, cache, system and internal storage
2. Flash 9.5.8 signed flashable zip
3. Flash kernel and Magisk or the other way round?

Camack said:
Thanks for the guide, my OnePlus 7 came with 9.5.5 and I want to clean flash to the latest 9.5.8. I have already unlocked the bootloader, boot into TWRP and installed TWRP, are these the correct steps to flash 9.5.8 as I'm confused with the A/B partition?
1. Wipe data, cache, system
2. Flash 9.5.8 signed flashable zip
3. Flash kernel and Magisk or the other way round?
Click to expand...
Click to collapse
1. Wipe data, cache, system and internal storage
2. Flash 9.5.8 signed flashable zip with current twrp
3. Flash twrp installer zip with current twrp
4. Flash magisk zip with current twrp
5. Reboot
Make sure not to FORMAT internal data, otherwise you wipe the files you want to flash as it formats sdcard

strongst said:
1. Wipe data, cache, system and internal storage
2. Flash 9.5.8 signed flashable zip with current twrp
3. Flash twrp installer zip with current twrp
4. Flash magisk zip with current twrp
5. Reboot
Make sure not to FORMAT internal data, otherwise you wipe the files you want to flash as it formats sdcard
Click to expand...
Click to collapse
Thanks, so I boot into TWRP first and then do step 1 and 2? Also, which step should I flash custom kernel?

Camack said:
Thanks, so I boot into TWRP first and then do step 1 and 2? Also, which step should I flash custom kernel?
Click to expand...
Click to collapse
You need to do all steps. I recommend to flash the custom kernel when you've sucessfully booted the device at first.

Hi, a new OP7 User here. I wanted to know how can i keep my data decrypted? i have installed TWRP but i want to decrypt my data and also keep it the same after updated newer updates. Is it possible? I was able to do it on my OP3T, so wanted to know if its possible on OP7 as well

murti52 said:
Hi, a new OP7 User here. I wanted to know how can i keep my data decrypted? i have installed TWRP but i want to decrypt my data and also keep it the same after updated newer updates. Is it possible? I was able to do it on my OP3T, so wanted to know if its possible on OP7 as well
Click to expand...
Click to collapse
This should work https://forum.xda-developers.com/android/software/universal-dm-verity-forceencrypt-t3817389

strongst said:
This should work https://forum.xda-developers.com/android/software/universal-dm-verity-forceencrypt-t3817389
Click to expand...
Click to collapse
I think i messed up real bad, now when iam booting the phone, a message comes, your device is corrupt. It can't be trusted and will not boot.

murti52 said:
I think i messed up real bad, now when iam booting the phone, a message comes, your device is corrupt. It can't be trusted and will not boot.
Click to expand...
Click to collapse
That message is the bootloader unlocked warning and comes every time as soon as you unlocked the bootloader.
Flashing DM verity patch can only be done when you format internal storage which wipes everything of your internal storage. You can't "decrypt" your existing data permanently with this.

strongst said:
That message is the bootloader unlocked warning and comes every time as soon as you unlocked the bootloader.
Flashing DM verity patch can only be done when you format internal storage which wipes everything of your internal storage. You can't "decrypt" your existing data permanently with this.
Click to expand...
Click to collapse
No, this is not the same, i can't even go to fastboot or anything, it's hardbricked.

murti52 said:
No, this is not the same, i can't even go to fastboot or anything, it's hardbricked.
Click to expand...
Click to collapse
If you have really bricked it: https://forum.xda-developers.com/oneplus-7/how-to/op7-unbrick-tool-to-restore-device-to-t3954325

strongst said:
If you have really bricked it: https://forum.xda-developers.com/oneplus-7/how-to/op7-unbrick-tool-to-restore-device-to-t3954325
Click to expand...
Click to collapse
Sadly it didn't worked, as phone doesn't gets detected on pc, keeps on rebooting. Gave it to service center and they are also not able to solve it ??. So a replacement for me ?
Edit : i think the force decryption was the culprit. When i rebooted, system was crashing. Op3t had its specific force decrypt file, not a general one, So i think as the development moves forward, op7 will also get it's own. Hoping the best ?

murti52 said:
Sadly it didn't worked, as phone doesn't gets detected on pc, keeps on rebooting. Gave it to service center and they are also not able to solve it ??. So a replacement for me ?
Edit : i think the force decryption was the culprit. When i rebooted, system was crashing. Op3t had its specific force decrypt file, not a general one, So i think as the development moves forward, op7 will also get it's own. Hoping the best ?
Click to expand...
Click to collapse
This file also works on OP7 pro, so it should also work on normal op7. I think the issue comes from something other.

strongst said:
This file also works on OP7 pro, so it should also work on normal op7. I think the issue comes from something other.
Click to expand...
Click to collapse
Then there must be some issue with my flashing sequence. Btw, The service centre repaired the issue and i have rooted it and using bluespark with stock rom. I'll give the zip another try later on when a new update comes. Thanks for the help

I believe the default file system is ext4, is there any benefits changing it to f2fs?

Jacckz said:
I believe the default file system is ext4, is there any benefits changing it to f2fs?
Click to expand...
Click to collapse
A good and quick overview and comparison with oneplus 7 pro https://sparrowsnews.com/2019/08/13/difference-between-f2fs-and-ext4-file-system/

[Guide][Installation][Fix]Switching from stock ROM to custom ROMs + Installing stock ROM after a brick or other Failures ( Mi A2 Lite - Daisy)

This guide is general guide for the installation of custom ROMs. I will also include guide to install stock ROM on devices which have been bricked or for solving various problem which you may encounter in custom ROMs. There are other guides for the same purpose but most of them are outdated and many of you seem to ignore old guide despite the fact that those guides can be helpful.
This is guide is only relevant for installation of custom ROMs which were released up to the date of posting this guide or up to android version 11. Recovering a bricked device can be done in the same way as to this one but installation instruction for devices with android version greater than 11 may differ.
DISCLAMER
Code:
I am NOT responsible for bricked devices,
thermonuclear war or for you getting fired because your alarm app failed.
Make sure the bootloader is unlocked and never lock the bootloader
How to unlock bootloader ?
>See in this thread.
Hard Brick, Soft brick, Problems in custom rom due to bad base, installation of base for switching to custom roms: windows linux
Installation of stock ROM through fastboot : The reply below
Migration from stock base to custom ROM : CLEAN FLASH
Migration between different version of same custom ROM : DIRTY FLASH
FOR SPECIFIC THREADS
Oragne Fox For Daisy
TWRP For Daisy
Magisk
CREDITS:
LInkBoi for his previous guide and TWRP
DarthJabba9 for Orange Fox Recovery
Every pros in daisy telegram groups.

EDL FLASHING (For windows only)​
EDL flashing can be helpful when flashing every partition of device is needed either for clean stock base or after brick or after some failure.
EDL flashing can be the final resort when everything else fails.
PREREQUISITES
1) A good USB cable, your phone
2) A PC with either windows or linux
3) Fastboot drivers from google and edl drivers from qualcomm
4) Platform tools from google
5)Fastboot rom. This should be full rom in .tgz format.
6)Xiaomi flash tool (LATEST VERSION AVAILABLE)
Install the adb and fastboot drivers from google. If you are on windows 10 or greater then you can also use "windows update > optional updates" to update adb and fastboot drivers + edl drivers. For the installation of drivers always use trusted sources and don't turn of driver signature enforcement if you can.
Extract the platform tools in a convenient folder, we will be doing our operations from this folder for fastboot and adb opeartions. Extract the fastboot ROM and place that in convenient folder as well. And for xiaomi flash tool extract the zip and launch XiaoMiFlash.exe .
If you can access fastboot in you phone then the phone can be booted into edl mode through fastboot else you have to take out back cover and short the testpoint pins to make the device boot into edl mode (see the attached image ).
If you can access fastboot. Boot into fastboot and type the following command in terminal.
To check if device is connected properly and drivers are properly installed
If no devices is shown then connect device properly with good usb cable and check the drivers.
Code:
fastboot devices
To boot phone into edl mode. This is only possible if the bootloader is unlocked else testpoint-edl is the only option
Code:
fastboot oem edl
The device should be shown as COM device in device manager ( Windows ). If not then either drivers aren't installed properly or your phone isn't in edl mode.
Now click on refresh button in xiaomi flash tool. Your device should be recognized as com device. Set the path to the images folder ( extracted fastboot rom ). Select CLEAN ALL option . If everything is good then click
on FLASH. The flashing process should start now. After the process completes keep pressing power button to boot device into the currently installed ROM.
Just install the rom and setup once even if you're going to flash custom rom next. This reduces various problems which may come in custom ROMs.
If any error occurs then try the following:
Make sure you are using latest flash tool.
Good fastboot rom (shouldn't be corrupted )
Good USB cable and try different ports of the PC.
The flashing should be done immediately after booting to edl. If not then take out battery and reconnect it if you have back cover open(In case of hard brick). Or keep pressing power button and volume down to boot into fastboot and boot to edl mode again from the above instructions(If fastboot is accessible)
For booting to edl using testpoint:
> Take out backcover
> Disconnect battery
> Short the pins
> Flash
> Connect battery after flashing is complete
> Keep pressing power button to boot into system.

qdl flashing ( linux only )​
For very detailed guide github -> bkerler edl
Thanks to DEFXZ and LinkBoi for suggesting this alternative.
Make sure you have platform tools, fastboot rom and other prerequisites to detect device properly.
clone the repository in convenient place
Code:
git clone https://git.linaro.org/landing-teams/working/qualcomm/qdl.git --depth=1
change to qdl directory
Code:
cd qdl
Build qdl tool
Code:
make
Finally flash the rom
Code:
./qdl --storage emmc --include /path/to/stock/images /path/to/stock/images/prog_emmc_firehose_8953_ddr.mbn /path/to/stock/images/rawprogram0.xml /path/to/stock/images/patch0.xml
The paths are the paths to various files inside the images folder which will be obtained after fastboot rom is extracted.
For further informations:
Original github link
qdl discussion in XDA

FASTBOOT FLASHING​
PREREQUISITES
FASTBOOT DRIVERS
PLATFORM TOOLS
FASTBOOT ROM
GOOD USB CABLE
PC WITH WORKING USB PORT
See this for meeting prerequisites.
Install fastboot drivers, connect device to PC via USB.
Extract platform tools into a convenient folder.
Extract fastboot ROM into a convenient folder.
Go to platform tools folder ( this will contain files and executable like fastboot.exe) and open powershell or any terminal window there
[ shift + right click and select open (powershell) window here ]
Type this command to see everything worked correctly.
Code:
fastboot devices
If not then check every step properly.
Now execute the script to flash the ROM.
Execute flash_all.bat script for windows PC.
Execute flash_all.sh script for linux PC.
If platform tools cannot be accessed system wide then.
Code:
./fastboot devices
will provide fastboot devices information.
For flashing drag and drop flash_all.bat or flash_all.sh file into the terminal.
Code:
'/media/user001/user/daisy/stock_roms/daisy_global_images_V10.0.18.0.PDLMIXM_9.0/flash_all.sh'
It will look something like this in linux and similar in windows.
If any error occurs the search for particular error. Most of the times the error is due to corrupted fastboot ROM or bad connection between phone and PC.

FINALLY! FLASHING CUSTOM ROM​
STEP 0
Flash(if not flashed already) the stock base recommended by particular ROM, if the ROM doesn't recommend a specific stock base flash 10.0.18.0 from the above instructions.
PREREQUISITES
TWRP or ORANGE FOX RECOVERY
Fastboot drivers and platform tools (details above )
The ROM which you want to flash, choose from here
GAPPS package if rom is vanilla and you want to install it.
Magisk if you want to root.
As you may have known by experience, our device doesn't have recovery partition so, flashing recovery through fastboot isn't possible. For flashing recovery first we need to boot recovery image and then only we can flash it.
If you want to use twrp:
Download both twrp*.zip and twrp*.img and place it in a convenient place.
If you want to use orange fox recovery:
Download orangeFox*.zip and extract it.
Keep both the .zip and .img file in convenient place.
If you have sdcard then copy ROM file, gapps, magisk, twrp or orange fox files into sdcard.
If not then there will be further instructions.
Now, connect the phone to the PC via USB and enable usb debugging. And open terminal in the platform tools folder as in above instructions.
Check device connectivity:
Code:
adb devices
Reboot into fastboot:
Code:
adb reboot bootloader
Check device connectivity:
Code:
fastboot devices
Lets check if the bootloader is unlocked:
Code:
fastboot oem device-info
If bootloader isn't unlocked you won't be able to flash custom recovery into the device. So, first unlock the bootloader. This should be allowed in the developers option of your phone first. This will factory reset the device.
Code:
fastboot oem unlock
Now if everything is good then it's time to boot into custom recovery:
Code:
fastboot boot recovery.img
recover.img is name of image of whichever custom recovery you want to use.
Code:
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
It's like this in my case. You can drag and drop after typing fastboot boot
The phone should now boot into custom recovery. If it ask for decryption then your lockscreen password should work there.
if you want to flash recovery only then find the recovery.zip you want and flash it.
The steps further is also valid for moving between different custom roms. The term used for such process is CLEAN FLASH.
For Flashing custom ROMS :
SOMETIMES FLASHING INSTRUCTIONS MAY DIFFER SO, BE SURE TO CROSS CHECK FOR INSTRUCTION IN ROM SPECIFIC XDA THREAD OR TELEGRAM GROUP
The following action will wipe userdata if not wiped already. Be sure to backup data before these steps. Also if you encounter any future problems full backup from custom recovery may be able to solve most of the problems. So, be sure to keep full backup(including every partition) of your device.
Go to main menu > wipe > select all except internal storage and microSD.
Swipe right to perform wipe.
Install custom recovery by flashing recovery.zip
(This is done in case adb push doesn't work below and sdcard isn't available for flashing)
Again go to main menu > wipe > format data
Type yes and press enter.
If you don't have files in your sdcard then:
push rom file + gapps + other files into your device through adb push.
The command will be something like this:
Code:
adb push '/media/user001/storage (1)/daisy/posp/potato_daisy-11-20210919-dumaloo.v4.2.3+20.Community.zip' /sdcard
If adb push fails to work then you can reboot recovery and simply copy the files through file explorer.
Reboot to recovery only if you had installed recovery after wiping system else the device will soft brick
Now flash the rom.zip by selecting the file and swiping right.
Flash custom recovery if the ROM doesn't contain recovery
We have to change current slot even if we don't want to flash anymore things.
Latest recoveries changes slot automatically So, go to main menu > reboot > recovery
Now flash files which you want to flash i.e. gapps and magisk.
Again, Don't flash gapps if the ROM is of Gapps variant
Most of the roms now have implemented FBE (File Based Encryption ). So, you need to format data before rebooting to system. Again, check for specific ROM installation instruction if that is required or not. If you keep data from previous ROM that won't be considered a clean flash so, for proper clean flash format data before rebooting to system.
reboot system

MOVING BETWEEN DIFFERENT VERSION OF SAME CUSTOM ROM
Dirty flash or OTA ​
Most of the newer ROMs have seamless update ( even the unofficial ones ). The OTA update is simple. Just go to updater ( in settings > system or native app, depends upon the rom). If your ROM is of vanilla version then make sure gapps and/or magisk which you have installed, your ROM and custom recovery all support addon.d survival script. If they don't then you may have to flash everything again after update process is complete.
If custom recovery itself doesn't support update then you may need to choose different recovery or dirty flash ROM from the recovery. Don't worry most of the roms and both the recoveries for daisy support OTA and addon.d survival.
DIRTY FLASH​The process of flashing a ROM on top of existing one keeping the /data partition intact is known as dirty flashing. Such flashing must be done only on different builds of same ROM and it isn't recommended to flash build of lower version on top of higher version.
The steps for dirty flashing:
Download the update package.
Reboot to recovery
Enter password for decryption if encrypted.
Flash the update.zip package.
Reboot recovery, if recovery/rom doesn't support survival of recovery then flash recovery before rebooting to recovery.
If gapps and/or magisk survival isn't supported then flash gapps and magisk, make sure gapps is of the same type which was flashed before.
reboot system

Hi @user-001 thanks for this.
I'm on a stock A2 lite thats never had anything done to it , am i right in thinking i follow the clean flash section ?
You mention in there
We have to change current slot even if we don't want to flash anymore things.
Click to expand...
Click to collapse
I'm not fully sure what that involves could you break it down the steps a little for me.
I've downloaded all the files and am set up but i'm unsure on the Flashing fastbbot section where you say to use these files..
Execute flash_all.bat script for windows PC.
Click to expand...
Click to collapse
Is this a section i can bypass ? if not where can i get them from ?
Cheers

steve.loveday said:
Hi @user-001 thanks for this.
I'm on a stock A2 lite thats never had anything done to it , am i right in thinking i follow the clean flash section ?
You mention in there
I'm not fully sure what that involves could you break it down the steps a little for me.
I've downloaded all the files and am set up but i'm unsure on the Flashing fastbbot section where you say to use these files..
Is this a section i can bypass ? if not where can i get them from ?
Cheers
Click to expand...
Click to collapse
1) Yes you should follow clean flash instructions.
2)Changing of slot is done in custom recovery. Precisely in the reboot menu. But newer recoveries automatically switch the slot after flashing the rom , just be sure to reboot to recovery after flashing the recovery zip file.
3) the flash_all.bat script will be inside the extracted rom(fastboot rom) folder. You can use xiaomiflash too for flashing through fastboot.

user-001 said:
1) Yes you should follow clean flash instructions.
2)Changing of slot is done in custom recovery. Precisely in the reboot menu. But newer recoveries automatically switch the slot after flashing the rom , just be sure to reboot to recovery after flashing the recovery zip file.
3) the flash_all.bat script will be inside the extracted rom(fastboot rom) folder. You can use xiaomiflash too for flashing through fastboot.
Click to expand...
Click to collapse
Hi thanks for the reply,
I'm getting confused with all the various guides all seem to want you to do it a different way.
As i'm wanting Lineage thier instructions are...
Installation:
Download the latest build from here
Download LinkBoi00's version of TWRP here
Reboot to bootloader (adb reboot bootloader)
Fastboot into TWRP recovery (fastboot boot twrp*.img)
Do a factory reset in TWRP
Flash the latest build of Lineage OS
Boot into your new phone
Click to expand...
Click to collapse
Theres no mention of the edl or fastboot flashing and also the fastbot rom i downloaded doesnt have the flash_all.bat script in the zip file.
So do i follow thier instructions or these ones ?
Cheers

steve.loveday said:
Theres no mention of the edl or fastboot flashing and also the fastbot rom i downloaded doesnt have the flash_all.bat script in the zip file.
So do i follow thier instructions or these ones ?
Cheers
Click to expand...
Click to collapse
This guide deals with how to do something rather than what to do, meaning you should always do what particular rom suggests but the way to do this is mentioned here.
edl or fastboot flashing comes under clean flashing with new base, most of the time you aren't required to do this.
The script should be clean_all.bat or something similar just don't execute script with lock in the name(it will lock the bootloader)
And if you're already on the recommended base you don't have to flash the fastboot rom.

First of all, thank you very much for the detailed guide. What you have done here took a lot of work to do but it will help a lot of people (including me) to understand, albeit rudimentarily, the structures and functions of the devices etc.
For all that, thanks again.
When I start using the guide, I will update this post with any questions, such as :
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
why not doing below? (For those who, like me, are not very familiar with linux.)
1. > adb push <twrp.img> /sdcard or same adb push "C:\platform-tools\twrp-3.5.2_9-2-daisy-unofficial.img" /sdcard
( which means push <file> from "adb|platform-tools\ folder" (eg. C:\platform-tools\)
into the root of <internal storage> | /storage/emulated/0 )
2. Reboot from adb to fastboot:
> adb reboot bootloader
3. Boot the image from <internal storage>:
> fastboot boot /sdcard/twrp-3.5.2_9-2-daisy-unofficial.img
What is the "Red" pointed and "Yellow" addresses"?
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'

I followed your "EDL FLASHING" post (#2) and it worked exactly as you mention!
In short, I was comming from unsuccessful flashing... but this is out of topic.
For me, did not worked the first time (after restarts) but the other day worked perfect.
The point is, most of times, it's becase windowz drivers.
We have to point that windowz needs their time to take the drivers in place. So, be patient and leave windowz to (not forced) restart(s).

AntonyMan said:
What is the "Red" pointed and "Yellow" addresses"?
fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img'
Click to expand...
Click to collapse
That must be your terminal representing different type of character in different colors.
Or, Are you talking about something else ?

steve.loveday said:
Theres no mention of the edl or fastboot flashing and also the fastbot rom i downloaded doesnt have the flash_all.bat script in the zip file.
So do i follow thier instructions or these ones ?
Cheers
Click to expand...
Click to collapse
For future references, the extracted fastboot ROM should be like this and you need to execute flash_all.bat or flash_all.sh script depending upon your OS or terminal.

user-001 said:
That must be your terminal representing different type of character in different colors.
Or, Are you talking about something else ?
Click to expand...
Click to collapse
Of course I'm talking about something else. lol
I was talking about that 'strange' address. fastboot boot '/media/user001/storage (1)/daisy/twrp/twrp-3.5.2_9-2-daisy-unofficial.img' (explained in post #11)
There is not such a directories in my miA2Lite phone. Obviously, it's because you are on Linux or Mac (UNIX). On Windowz 'command prompt' syntax it's slightly different.
Thus, I typed fastboot boot "/sdcard/twrp-3.5.2_9-2-daisy-unofficial.img"
* /sdcard is the root of <internal storage> directory.
** On Windows, double quote the address, if it's include spaces.

AntonyMan said:
Of course I'm talking about something else. lol
I was talking about that 'strange' address. There is not such a directories in my miA2Lite phone.
Thus, I typed fastboot boot "/sdcard/twrp-3.5.2_9-2-daisy-unofficial.img"
* /sdcard is the root of <internal storage> directory.
** On Windows, double quote the address, if it's include spaces.
Click to expand...
Click to collapse
The twrp image was on my pc(linux) i was booting directly from pc's terminal. And if you use only adb(or fastboot) then the paths are pc's absolute paths.

[GUIDE] Pixel 5 "redfin": Unlock Bootloader, Update, Root, Pass SafetyNet

If you are looking for my guide on a different Pixel, find it here:
Pixel 3
Pixel 3XL
Pixel 3a
Pixel 3aXL
Pixel 4
Pixel 4XL
Pixel 4a
Pixel 4a (5G)
Pixel 5a
Pixel 6
Pixel 6 Pro
For best results, use the latest stable Magisk release.
Discussion thread for migration to 24.0+.
Note: Magisk prior to Canary 23016 does not incorporate the necessary fixes for Android 12+.
WARNING: YOU AND YOU ALONE ARE RESPONSIBLE FOR ANYTHING THAT HAPPENS TO YOUR DEVICE. THIS GUIDE IS WRITTEN WITH THE EXPRESS ASSUMPTION THAT YOU ARE FAMILIAR WITH ADB, MAGISK, ANDROID, AND ROOT. IT IS YOUR RESPONSIBILITY TO ENSURE YOU KNOW WHAT YOU ARE DOING.
Prerequisites:
Latest SDK Platform Tools - if Platform Tools is out of date, you WILL run into problems!
USB Debugging enabled
Google USB Driver installed
I recommend using Command Prompt for these instructions; some users have difficulty with PowerShell.
Make sure the Command Prompt is running from your Platform Tools directory!
Android Source - Setting up a device for development
Spoiler: Downloads
Pixel OTA Images
Pixel Factory Images
Magisk Stable, Magisk Canary - Magisk GitHub
Spoiler: Unlock Bootloader
Follow these instructions to enable Developer Options and USB Debugging.
Enable OEM Unlocking. If this option is grayed out, unlocking the bootloader is not possible.
Connect your device to your PC, and open a command window in your Platform Tools folder.
Ensure ADB sees your device:
Code:
adb devices
If you don't see a device, make sure USB Debugging is enabled, reconnect the USB cable, or try a different USB cable.
If you see "unauthorized", you need to authorize the connection on your device.
If you see the device without "unauthorized", you're good to go.
Reboot to bootloader:
Code:
adb reboot bootloader
Unlock bootloader: THIS WILL WIPE YOUR DEVICE!
Code:
fastboot flashing unlock
Select Continue on the device screen.
Spoiler: Initial Root / Create Master Root Image
Install Magisk on your device.
Download the factory zip for your build.
Inside the factory zip is the update zip: "device-image-buildnumber.zip". Open this, and extract boot.img
Copy boot.img to your device.
Patch boot.img with Magisk: "Install" > "Select and Patch a File"
Copy the patched image back to your PC. It will be named "magisk_patched-23xxx_xxxxx.img". Rename this to "master root.img" and retain it for future updates.
Reboot your device to bootloader.
Flash the patched image:
Code:
fastboot flash boot <drag and drop master root.img here>
Reboot to Android. Open Magisk to confirm root - under Magisk at the top, you should see "Installed: <Magisk build number>
Spoiler: Update and Root Automatic OTA
Before you download the OTA, open Magisk, tap Uninstall, then Restore Images. If you have any Magisk modules that modify system, uninstall them now.
Take the OTA update when prompted. To check for updates manually, go to Settings > System > System Update > Check for Update
Allow the update to download and install. DO NOT REBOOT WHEN PROMPTED. Open Magisk, tap Install at the top, then Install to inactive slot. Magisk will then reboot your device.
You should now be updated with root.
Spoiler: Update and Root OTA Sideload
Download the OTA.
Reboot to recovery and sideload the OTA:
Code:
adb reboot sideload
Once in recovery:
Code:
adb sideload ota.zip
When the OTA completes, you will be in recovery mode. Select "Reboot to system now".
Allow system to boot and wait for the update to complete. You must let the system do this before proceeding.
Reboot to bootloader.
Boot the master root image (See note 1):
Code:
fastboot boot <drag and drop master root.img here>
Note: If you prefer, you can download the factory zip and manually patch the new boot image, then flash it after the update. Do not flash an older boot image after updating.
Your device should boot with root. Open Magisk, tap Install, and select Direct Install.
Reboot your device. You should now be updated with root.
Note: You can use Payload Dumper to extract the contents of the OTA if you want to manually patch the new boot image. However, I will not cover that in this guide.
Spoiler: Update and Root Factory Image
Please note that the factory update process expects an updated bootloader and radio. If these are not up to date, the update will fail.
Download the factory zip and extract the contents.
Reboot to bootloader.
Spoiler: Update bootloader if necessary
Compare bootloader versions between phone screen and bootloader.img build number
Code:
fastboot flash bootloader <drag and drop new bootloader.img here>
If bootloader is updated, reboot to bootloader.
Spoiler: Update radio if necessary
Compare baseband versions between phone screen and radio.img build number
Code:
fastboot flash radio <drag and drop radio.img here>
If radio is updated, reboot to bootloader.
Apply update:
Code:
fastboot update --skip-reboot image-codename-buildnumber.zip
When the update completes, the device will be in fastbootd. Reboot to bootloader.
Boot the master root image (See note 1):
Code:
fastboot boot <drag and drop master root.img here>
Note: If you prefer, you can manually patch the new boot image, then flash it after the update. Do not flash an older boot image after updating.
Your device should boot with root. Open Magisk, tap Install, and select Direct Install.
Reboot your device. You should now be updated with root.
Note: If you prefer, you can update using the flash-all script included in the factory zip. You will have to copy the script, bootloader image, radio image, and update zip into the Platform Tools folder; you will then have to edit the script to remove the -w option so it doesn't wipe your device.
The scripted commands should look like this:
Code:
fastboot flash bootloader <bootloader image name>
fastboot reboot bootloader
ping -n 5 127.0.0.1 > nul
fastboot flash radio <radio image name>
fastboot reboot bootloader
ping -n 5 127.0.0.1 > nul
fastboot update --skip-reboot <image-device-buildnumber.zip>
Once this completes, you can reboot to bootloader and either boot your master patched image, or if you patched the new image, flash it at this time.
Spoiler: Update and Root using PixelFlasher <<RECOMMENDED FOR NOVICES>>
PixelFlasher by @badabing2003 is an excellent tool that streamlines the update process - it even patches the boot image for you.
The application essentially automates the ADB interface to make updating and rooting much easier. However, it is STRONGLY recommended that you still learn the "basics" of using ADB.
For instructions, downloads, and support, please refer to the PixelFlasher thread.
Spoiler: Update and Root using the Android Flash Tool
Follow the instructions on the Android Flash Tool to update your device. Make sure Lock Bootloader and Wipe Device are UNCHECKED.
When the update completes, the device will be in fastbootd. Reboot to bootloader.
Boot the master root image (See note 1):
Code:
fastboot boot <drag and drop master root.img here>
Note: If you prefer, you can download the factory zip and manually patch the new boot image, then flash it after the update. Do not flash an older boot image after updating.
Your device should boot with root. Open Magisk, tap Install, and select Direct Install.
Reboot your device. You should now be updated with root.
Spoiler: Pass SafetyNet/Play Integrity
SafetyNet has been deprecated for the new Play Integrity API. More information here.
In a nutshell, Play Integrity uses the same mechanisms as SafetyNet for the BASIC and DEVICE verdicts, but uses the Trusted Execution Environment to validate those verdicts. TEE does not function on an unlocked bootloader, so legacy SafetyNet solutions will fail.
However, @Displax has modified the original Universal SafetyNet Fix by kdrag0n; his mod is able to force basic attestation instead of hardware, meaning that the device will pass BASIC and DEVICE integrity.
Mod available here. Do not use MagiskHide Props Config with this mod.
This is my configuration that is passing Safety Net. I will not provide instructions on how to accomplish this. Attempt at your own risk.
Zygisk + DenyList enabled
All subcomponents of these apps hidden under DenyList:
Google Play Store
GPay
Any banking/financial apps
Any DRM media apps
Modules:
Universal SafetyNet Fix 2.3.1 Mod - XDA post
To check SafetyNet status:
YASNAC - GitHub
To check Play Integrity status:
Play Integrity Checker - NOTE: MEETS_STRONG_INTEGRITY will ALWAYS fail on an unlocked bootloader.
I do not provide support for Magisk or modules. If you need help with Magisk, here is the Magisk General Support thread. For support specifically with Magisk v24+, see this thread.
Points of note:
The boot image is NOT the bootloader image. Do not confuse the two - YOU are expected to know the difference. Flashing the wrong image to bootloader could brick your device.
While the Magisk app is used for patching the boot image, the app and the patch are separate. This is what you should see in Magisk for functioning root:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
"Installed" shows the version of patch in the boot image. If this says N/A, you do not have root access - the boot image is not patched, or you have a problem with Magisk.
"App" simply shows the version of the app itself.
If you do not have a patched master boot image, you will need to download the factory zip if you haven't already, extract the system update inside it, then patch boot.img.
If you prefer updating with the factory image, you can also extract and manually patch the boot image if desired.
Some Magisk modules, especially those that modify read only partitions like /system, may cause a boot loop after updating. As a general rule, disable these modules before updating. You are responsible for knowing what you have installed, and what modules to disable.
Credits:
Thanks to @badabing2003 , @pndwal , @Displax , @Az Biker , @ipdev , @kdrag0n , @Didgeridoohan , and last but not least, @topjohnwu for all their hard work!

V0latyle said:
As many of you know by now, in order to run a patched boot image on Android 12 requires disabling Android Boot Verification.
On Android 12, disabling verity and verification will require a data wipe if it hasn't been done before. What seems to "lock" the state of boot verification is booting into system; so, if you perform an update, or flash vbmeta without the disable flags, then reboot into Android, you have essentially enabled boot verification and will require a wipe to disable it again. Confusing, I know.
Here is the appropriate update process. DO NOT take the automatic OTA if you are rooted. If you allow the phone to reboot after an update without disabling boot verification, you will have to wipe in order to disable it again, as you would need to for a patched boot image.
***Note***: The boot image doesn't have to be patched before you perform the update. Some have found it works better to update, THEN patch the boot image.
OTA Sideload:
1. Download both the OTA and the factory zip.
2. Extract vbmeta.img and boot.img from the factory zip.
3. Patch the boot image and copy it back to your computer.
4. Reboot to recovery and sideload the OTA: select Apply Update via ADB, then on your PC:
Code:
adb sideload ota.zip
5. When the OTA completes, you will be in recovery mode. DO NOT REBOOT TO SYSTEM. Select "Reboot to bootloader".
6. Reflash vbmeta to disable boot verification:
Code:
fastboot flash vbmeta --disable-verity --disable-verification --slot=all vbmeta.img
7. Flash patched boot image:
Code:
fastboot flash boot --slot=all magisk_patched-23xxx_xxxxx.img
8. Reboot to system.
Factory update:
1. Download the factory zip.
2. Extract boot.img
3. Patch the boot image and copy it back to your computer.
4. Reboot to bootloader.
5. Apply update:
Code:
fastboot update --disable-verity --disable-verification --skip-reboot image-codename-buildnumber.zip
6. Flash patched boot image:
Code:
fastboot flash boot --slot=all magisk_patched-23xxx_xxxxx.img
7. Reboot to system.
Android Flash Tool:
1. Download the factory zip.
2. Extract boot.img
3. Patch the boot image and copy it back to your computer.
4. Reboot to bootloader.
5. Follow the instructions on the Android Flash Tool to update your device. The ONLY boxes you should check are "Disable Verity" and "Disable Verification"
6. When the update completes, the phone will reboot to system without root.
7. Reboot to bootloader and flash patched boot image:
Code:
fastboot flash boot --slot=all magisk_patched-23xxx_xxxxx.img
8. Reboot to system.
REMEMBER: The most critical part of this is making sure verity and verification are disabled during the update process before the phone reboots. If you forget to patch the boot image, that's OK - you don't have to flash /boot right after update.
If you have trouble with the patched boot image, simply flash /boot back to stock and allow Android to boot, then re-patch and re-flash the boot image.
You can also, if you want, boot the patched image instead of flashing it:
Code:
fastboot boot magisk_patched-23xxx_xxxxx.img
This is considered "temporary boot" as it loads the image from your PC rather than from device storage. You can use this to confirm root works, and if you so desire, you can then perform Direct Install in Magisk.
Click to expand...
Click to collapse
You Sir are all over these forums spreading helpful advice, and knowledge. I would just like to say Thank You for all you do here. It's so greatly appreciated. You are one of the many people who make this place so special.
Also, Thank You for your service to our country.

@V0latyle can you link me to a web page that would list every adb and fastboot command that we as android modders would use. What I mean is I couldn't find a Google search that listed the fastboot command with --slot=all among other adb and fastboot commands

Krsmqn said:
You Sir are all over these forums spreading helpful advice, and knowledge. I would just like to say Thank You for all you do here. It's so greatly appreciated. You are one of the many people who make this place so special.
Also, Thank You for your service to our country.
Click to expand...
Click to collapse
I agree with @Krsmqn, @V0latyle THANK YOU FOR YOUR SERVICE !!!!! in the military and for your service in the xda community

I used the Android Flash Tool method to update to the November build, and followed the instructions precisely. It worked flawlessly. My deny list is exactly the same in Magisk, and all my modules are working perfectly. I didn't even have to disable them. I think I will use this method from now on.

Krsmqn said:
You Sir are all over these forums spreading helpful advice, and knowledge. I would just like to say Thank You for all you do here. It's so greatly appreciated. You are one of the many people who make this place so special.
Also, Thank You for your service to our country.
Click to expand...
Click to collapse
elong7681 said:
I agree with @Krsmqn, @V0latyle THANK YOU FOR YOUR SERVICE !!!!! in the military and for your service in the xda community
Click to expand...
Click to collapse
Thanks guys, I appreciate it.
elong7681 said:
@V0latyle can you link me to a web page that would list every adb and fastboot command that we as android modders would use. What I mean is I couldn't find a Google search that listed the fastboot command with --slot=all among other adb and fastboot commands
Click to expand...
Click to collapse
Boy, I wish I had that handy, because I could sure use it too! I don't have your answer but hopefully someone else does, because believe me I'll be bookmarking it!

Will this work on Android Pixel 5a?

Rafiul Bari Chowdhury said:
Will this work on Android Pixel 5a?
Click to expand...
Click to collapse
Yes. The root process is exactly the same for the 4a 5g, 5, and 5a. The update process is the same across all Pixel devices.

I patched the boot.img. Magisk 23 did not report errors. But size of the patched file is zero. This looks not promising...

nostromo12 said:
I patched the boot.img. Magisk 23 did not report errors. But size of the patched file is zero. This looks not promising...
Click to expand...
Click to collapse
What version of Magisk did you use?

The stabil one

Will this work on Android Pixel 5a?
V0latyle said:
Yes. The root process is exactly the same for the 4a 5g, 5, and 5a. The update process is the same across all Pixel devices.
Click to expand...
Click to collapse
Okay. But Should I Remove Magisk Fully before upgrading through ADB/Fastboot/AFT?

H,
I'm on Android 11 pixel 5, can I use this tutorial ?

I think it's safer to unroot/remove Magisk and modules when going from 11 to 12 right? Some modules might not be compatible with 12 causing bootloops.

thecompany said:
I think it's safer to unroot/remove Magisk and modules when going from 11 to 12 right? Some modules might not be compatible with 12 causing bootloops.
Click to expand...
Click to collapse
You're going to have to wipe /data anyway if you intend to root on Android 12. Unless you're willing to try an idea I have.

Thanks V0latyle !!
I follow the flash tool method for update from october to november on my pixel 5
Perfect update, no issues and all data ok

nico22320 said:
Thanks V0latyle !!
I follow the flash tool method for update from october to november on my pixel 5
Perfect update, no issues and all data ok
Click to expand...
Click to collapse
Did you use Magisk canary? It is not necessary to check wipe in the android flash tool?
I use standard Magisk and can not change the update path to canary

nostromo12 said:
Did you use Magisk canary? It is not necessary to check wipe in the android flash tool?
I use standard Magisk and can not change the update path to canary
Click to expand...
Click to collapse
No i use the beta version of magisk.
You need wipe only for update from Android 11 to Android 12.
Just follow the guide for update to november and enjoy

nico22320 said:
No i use the beta version of magisk.
You need wipe only for update from Android 11 to Android 12.
Just follow the guide for update to november and enjoy
Click to expand...
Click to collapse
I want to upgrade from 11 (oktober) to 12
In the first message from this thread concerning the flash tool there was no wipe mentioned.
I want to update keeping my data ! How to proceed?

The best way: save yours photos etc with your Google account and make a fresh install with Factory image on Android 12 ( with disable verity and vérification)
It's long for set up device but 100% of chance of work with no issues for futurs update
Sûre you Can try to update without wipe and disable verity and vérification but maybe bootloops or not