Related
I have the official Nexus One dock and it randomly disconnects from the phone while it's still docked. BT disconnects and it stops charging. It seems to happen more often when the phone gets hotter.
I have a feeling it's software related because it usually re-connects as soon as I change the orientation or un-dock re-dock really quick.
The only other thing that I can think of is that maybe it needs a better ground since I hardwired it into my car's power wiring.
Anyone else experience this?
Ive been meaning to make a thread similar to this but i guess its more appropriate not to waist threads...
The touch sensitivity dies when the screen is on for prolonged periods of time. for example when its in the gps dock, i will sometimes try to interact with the app and it wont register any touches at all or will get them completely off. but right when i turn off the screen then turn it back on again (even if its quickly) it'll go back to normal. Why? is it because of the heat being created? the phone does get hot when i use the gps for a long time.
I blame poor connections. Every now and again i have to wiggle the base of the dock where the contact pins are to seat the contacts
The screen is supposed to auto recalibrate, it doesn't seem to do a very good job of it. My phone is hopeless on winter mornings, about 30 seconds after turning it on in the morning I have to turn the display off and on again to force it to recalibrate or the bottom 1/3 of the screen stops working.
The issue is much less pronounced with the CM firmware than it is with the stock firmware though.
My fix for the Nexus dock
I also had this problem when I was using the phone in the horizontal position but when I turned it to vertical it started working again... not an ideal fix but it worked for me... also I found a small crack in the dock that makes the tab at the top stiff, it eventually broke through and I used a piece of shrink tubing to repair it back to help it push down on the prongs at the bottom.
On the other topic this screen sensitivity problem should be marked critical since I can't answer my phone without turning the screen off and back on again, I can't even count the amount of times I hung up on someone while fumbling to answer the phone.
Mobiper.com
The CurveFish OnOff widgets were the first widgets I downloaded when I got my new Motorola DROID. I needed to have complete control over my connections to save on battery life, and found a few little fun widgets along the way. And to have found a publisher that has released multiple widgets of the same theme excites the OCD inside me.
mobiper said:
The CurveFish OnOff widgets were the first widgets I downloaded when I got my new Motorola DROID. I needed to have complete control over my connections to save on battery life, and found a few little fun widgets along the way. And to have found a publisher that has released multiple widgets of the same theme excites the OCD inside me.
Click to expand...
Click to collapse
Which of the widgets fixes the dock calibration issues?
Finally got my app up and running on the Market and being a die hard Galaxy Note and xda user, I thought it would only be appropriate to post it here for fellow users to enjoy. =)
IntelliCover is a utility which uses your device’s proximity sensor to control its display and allow fast and efficient access to your phone or tablet.
It turns the screen turns off automatically when you put your device in your pockets, close its flip cover, store the device in a bag, or even just leave the device facing down on a table. As soon as the device is back in your hand the proximity sensor is triggered again, the screen turns back on and your phone is instantly ready for use.
IntelliCover is more feature-filled than any other similar application on the market. And the best part? It's FREE!
Click here to visit the market page and download the app for free
P.S. If you find a bug, I'd appreciate if you could report it to me before giving a bad rating because it usually only takes me less than a day to fix.
*** Features ***
Calibration:-
Proximity Sensor Delay – Add a delay to the time takes to trigger the sensor and turn the screen off.
Application Settings:-
Automatic Unlock – Automatically dismiss the Unlock Screen, provided there is no password. *Experimental*
Disable in Landscape Mode – Disable the proximity sensor when an application is in landscape mode.
Go to Home Screen – Show the home screen when the screen turns on.
Screen Off Only – The screen will turn off but not on when the proximity sensor is triggered.
Screen On Only – The screen will turn on but not off when the proximity sensor is triggered.
Start on Boot – Automatically start the IntelliCover service when the device turns on.
Notifications:-
Proximity Warning – Vibrate every time the proximity sensor is triggered.
Status Bar Notification – Show an ongoing notification in the status bar.
Screen On and Off Actions:-
Airplane Mode – Enable or disable airplane mode.
Auto Rotate (will be removed) – Activate or deactivate.
Auto Sync – Activate or deactivate auto-sync.
Bluetooth – Enable or disable Bluetooth.
Haptic Feedback (will be removed) – Activate or deactivate haptic feedback.
Ringer Mode – Switch ringer mode to Normal (Sound with Vibration), Vibrate or Silent.
Wi-fi – Enable or disable wi-fi.
*** Frequently Asked Questions ***
Q) Is it really free? Where are the ads?
Ans) IntelliCover is completely free and has no ads whatsoever!
Q) Do I require a rooted device to use IntelliCover?
Ans) Nope. IntelliCover works on all supported phones and tablets, rooted or unrooted.
Q) Doesn’t using the proximity sensor consume a lot of battery?
Ans) Actually, the proximity sensor consumes minimal power, almost little enough to be insignificant.
Q) What are the ‘Screen On’ and ‘Screen Off’ actions?
Ans) IntelliCover allows you to set events to be triggered when the screen turn on or off. For example, by setting wi-fi to turn on when your screen turns on and setting it to turn off when the screen turns off, you could save a huge amount of battery power.
Q) Can I request a feature?
Ans) Of course! Head over to the Contact section to drop me an e-mail.
Q) Why does IntelliCover keep running in the background?
Ans) It has to run in the background to know when the proximity sensor is triggered.
Q) How can I uninstall the application?
Ans) First you must go into Security settings and remove IntelliCover from System Administrator. Then it can be uninstalled like any other application.
Q) Can I donate to the developer?
Ans) Not yet but hopefully I’ll have something set up soon.
*** Permissions Required ***
INTERNET - Required for error logging (to send crash reports)
WAKE_LOCK - Required to unlock screen
WRITE_SETTINGS - Required to toggle ringer mode
VIBRATE - Required to vibrate phone
RECEIVE_BOOT_COMPLETED - Required to detect phone boot
WRITE_SYNC_SETTINGS - Required to toggle autosync
READ_SYNC_SETTINGS - Required to toggle autosync
BLUETOOTH - Required to toggle bluetooth
BLUETOOTH_ADMIN - Required to toggle bluetooth
ACCESS_WIFI_STATE - Required to toggle WiFi
UPDATE_DEVICE_STATS - Required to toggle WiFi
CHANGE_WIFI_STATE - Required to toggle WiFi
*** Contact ***
Feel free to contact me at [email protected] with any issues, bug reports, feature requests, suggestions or queries. Please read the FAQ above before sending an e-mail to avoid redundancy.
Click here to visit the market page and download the app for free
Nice one mate.really good work.
Keep it up:thumbup:
Sent from my GT-N7000 using xda app-developers app
awsome app . really good
but need some work as ... i may close the phone an put it over the table ..... need option to not turn on the screen when its turn off manual
what happen when my hand somehow moves to the proximity sensor?
shivg86 said:
Nice one mate.really good work.
Keep it up:thumbup:
Sent from my GT-N7000 using xda app-developers app
Click to expand...
Click to collapse
Thanks! It's my first app so hearing from happy users is really exciting and inspiring.
engfantom said:
awsome app . really good
but need some work as ... i may close the phone an put it over the table ..... need option to not turn on the screen when its turn off manual
Click to expand...
Click to collapse
Oh I get it. Thanks for pointing that out. I'll try to fix it as soon as possible. I have exams right now but after that (in a week probably) I'll release a fixed, updated version. And thanks also for the rating. With a new app, it really helps to get good ratings
meethere said:
what happen when my hand somehow moves to the proximity sensor?
Click to expand...
Click to collapse
Well there is a delay option. So you could set a delay of 2-3 seconds or more so that if you move your hand by mistake to the proximity sensor, it won't just turn off, it'll be delayed. Or you could set the vibrate function on so if your hand goes there, the phone will vibrate to warn you about it. :good:
Downloaded and voted with five stars.
Thanks mate. :laugh:
Downloading rite now..
good idea ! But, it's not working with flip cover.
Indeed, the screen turn off when the flip cover is at 5mm of the sensor but it turns on again when completely closed!!!
can you fix that?
keep on the good work ...
Sent from my GT-N7000 using xda app-developers app
samvox said:
good idea ! But, it's not working with flip cover.
Indeed, the screen turn off when the flip cover is at 5mm of the sensor but it turns on again when completely closed!!!
can you fix that?
keep on the good work ...
Sent from my GT-N7000 using xda app-developers app
Click to expand...
Click to collapse
Hmm...not sure. It works with my flip cover. Almost all phones (like Galaxy Note) have a proximity sensor that only detects FAR or NEAR. So even though I've told the application to turn the screen off when an object comes to a certain distance, either the hardware itself or the phone's firmware doesn't have the ability to detect the distance. Proximity sensors are only made to be used when on a call so it doesn't really need to detect distance in its regular everyday usage I guess.
I did have a similar problem to yours when testing with a sort of snake-skin leather Zenus case because it had some tiny ridges in it, but in most test cases it worked. I'll try my best to see if I can dig up a solution. =)
If I remember well, it depends on the color of the cover.
Darker means that the proximity doesn't work very well.
I have another proximity app, I'll switch to this one very soon, and I have to put a little white stripe on the cover,where the sensor is, to make it work correctly.
If I'm not wrong,is an issue with all the sensors and not a program fault.
Inviato dal mio GT-N7000 con Tapatalk 2
raistlin74 said:
If I remember well, it depends on the color of the cover.
Darker means that the proximity doesn't work very well.
I have another proximity app, I'll switch to this one very soon, and I have to put a little white stripe on the cover,where the sensor is, to make it work correctly.
If I'm not wrong,is an issue with all the sensors and not a program fault.
Inviato dal mio GT-N7000 con Tapatalk 2
Click to expand...
Click to collapse
Now that I think about it, that actually makes alot of sense. I don't know what it is with ALL sensors and black but they do tend to freak out. I even have an amazing Logitech mouse that works on mirrors and glass and see-through plastic and anywhere else except for on pitch black surfaces lol. The only crude fix I could think of is to use a combo of proximity sensor and light sensor somehow but it would be a waste of battery in my opinion.
Just tried your app, but didn't really worked : when I flip my (black) cover (or when I hide the sensor with my finger), the screens goes off but just for few seconds before getting on again. I'm using WidgetLocker btw, I don't know if it affects your app or not.
Edit : if you need logs or anything, feel free to ask
Sine. said:
Just tried your app, but didn't really worked : when I flip my (black) cover (or when I hide the sensor with my finger), the screens goes off but just for few seconds before getting on again. I'm using WidgetLocker btw, I don't know if it affects your app or not.
Edit : if you need logs or anything, feel free to ask
Click to expand...
Click to collapse
Hi! I'm still searching into it but it would seem that darker colors do not work well with the proximity sensor. Since this doesn't really have much to do with the actual programming itself I'm not sure I can do much about that.
BUT it should work when you use your finger. WidgetLocker shouldn't make a difference, it just works like any other lockscreen so it won't affect the functionality of my app. The fact that it turns on after a while baffles me though, because programmatically it doesn't make sense to me.
If you don't mind, could you please try putting the phone down on a surface or putting it in your pocket to test it? The proximity sensor is pretty sensitive so if you'd moved your finger even a bit it could have gotten triggered. Let me know if it still doesn't work and then we can move on to the messy part.
*yawn* Time for bed
This is happening right now!
Sorry, was just shocked when I actually saw the posting dates/time, I always assume apps have been around and had the bugs worked out, but I see this is newly born! So, for an i717 Note (AT&T Branded) this should essentially work the same, right? I mean there are no processor specific requirements or such? I am a releatively new Note owner - just a few days, and I have rooted, flashed a nice ROM, and ordered an awesome leather cover (NOT the cheesy flip cover) and I went looking for a proximity sensor based "cover detection app" - this sounds good, nice options to fine tune, and the dev sounds really into making this work well. Sounds like a winner. I will grab this now, but will not have my cover till Monday. It is NOT black, LOL, so I will test and report how well it works soon after i get my cover. I also got the Samsung branded car mount (I am going broke getting these, for my HTC phones, then GSII, then GSII Skyrocket (slightly larger) and now Note (LOTS LARGER, LOL!) Oh, so why am I telling you about my car dock? Because it's awesome, LOL!!! Nah, just kidding, (but it IS awesome) - I am wondering if being in a darkened car, like at night might trip the proximity sensors threshold for available light and kill the screen. Anyway, if you don't know that's okay. If it does trip the sensor, I will let you know.
Thanks again for a quality app, with no ads, and free. Always a pleasure - gonna put a price on it when it's perfect? If so remember your testers, hehe.
awsome app, nice job !:good:
SmartAs$Phone said:
Sorry, was just shocked when I actually saw the posting dates/time, I always assume apps have been around and had the bugs worked out, but I see this is newly born! So, for an i717 Note (AT&T Branded) this should essentially work the same, right? I mean there are no processor specific requirements or such? I am a releatively new Note owner - just a few days, and I have rooted, flashed a nice ROM, and ordered an awesome leather cover (NOT the cheesy flip cover) and I went looking for a proximity sensor based "cover detection app" - this sounds good, nice options to fine tune, and the dev sounds really into making this work well. Sounds like a winner. I will grab this now, but will not have my cover till Monday. It is NOT black, LOL, so I will test and report how well it works soon after i get my cover. I also got the Samsung branded car mount (I am going broke getting these, for my HTC phones, then GSII, then GSII Skyrocket (slightly larger) and now Note (LOTS LARGER, LOL!) Oh, so why am I telling you about my car dock? Because it's awesome, LOL!!! Nah, just kidding, (but it IS awesome) - I am wondering if being in a darkened car, like at night might trip the proximity sensors threshold for available light and kill the screen. Anyway, if you don't know that's okay. If it does trip the sensor, I will let you know.
Thanks again for a quality app, with no ads, and free. Always a pleasure - gonna put a price on it when it's perfect? If so remember your testers, hehe.
Click to expand...
Click to collapse
lol Well let's get one thing out the way. This app is and will be free (and ad-free) forever. So don't worry about that. Who knows, maybe a long way into the future I might release a paid app to earn a little cash but I don't plan on doing so anytime soon, and surely not to this app.
As for compatibility, as long as your phone has a proximity sensor the app should work (though I'm working out some problems on the smaller phones) so yes, it should work on your phone, no problem. Just hope it works out with your cover though. My cover is sort of a really dark deep brown and it doesn't work at times so I tend not to use that one. I do alot of coding and testing at night btw, and it doesn't just trigger the proximity sensor, so I strongly doubt a darkened car would trigger it.
Good luck with your Note btw. I really think you made the right choice. I've had mine for a year now. I'm just in college so I can't buy Note 2 or I would have. The way Samsung talks about Note 2 though makes me believe I'll have the chance to grab a Note 3 sometime in the future. =)
YES! FINALLY! Fix for all Gingerbread devices coming soon. Should be up within a day or two after some testing. Then I'll work on widgets and optimization and other stuff after I'm done with exams.
i installed this app. but when i close the flip cover, it just locks the screen . opening the cover does nothing
it doesn't properly works
I don't know why, but when I put my finger on sensor it works, with my black cover don't
nokiamodeln91 said:
i installed this app. but when i close the flip cover, it just locks the screen . opening the cover does nothing
Click to expand...
Click to collapse
Could you please give me a little more information? Just basic stuff like the device model and Android version and whatever else you think is important, and I'll look into the issue.
Giopon said:
I don't know why, but when I put my finger on sensor it works, with my black cover don't
Click to expand...
Click to collapse
Yes, unfortunately this isn't a problem with the application. Proximity sensors don't work well on darker colors. That's why it might work with your finger and maybe in your pocket but not with a black cover. Sorry, this is a problem with hardware, not with the app, so I can't fix that. Only thing I can tell you is that you're not alone. Pretty much all proximity sensors have trouble with black, not just yours.
So apparently on Samsungs official news site , the AOD display has a sensor that will disable the AOD when it's placed inside a pocket or a bag (Why would your watch be in your pocket or bag instead of your wrist?). You would think this would also work if say you're wearing a long sleeve shirt. I have been unable to trigger this via long sleeve shirts and I don't have thin enough clothing to test the pocket, nor do I own a bag to test.
"The device’s 3-inch circular Super AMOLED display has a resolution of 360 x 360. Its 16 million colors, full color Always On Watch continuously shows the time rather than fading to black. The ambient light sensor helps to adjust the brightness of displayed information and works to automatically disable the Always On Watch when users can’t see the screen, such as when the watch is in a pocket or a bag. Users can opt to personalize their Always On Watch with customizable, interactive watch faces."
Who's willing to help me test this feature?
Naturesretard said:
So apparently on Samsungs official news site , the AOD display has a sensor that will disable the AOD when it's placed inside a pocket or a bag (Why would your watch be in your pocket or bag instead of your wrist?). You would think this would also work if say you're wearing a long sleeve shirt. I have been unable to trigger this via long sleeve shirts and I don't have thin enough clothing to test the pocket, nor do I own a bag to test.
"The device’s 3-inch circular Super AMOLED display has a resolution of 360 x 360. Its 16 million colors, full color Always On Watch continuously shows the time rather than fading to black. The ambient light sensor helps to adjust the brightness of displayed information and works to automatically disable the Always On Watch when users can’t see the screen, such as when the watch is in a pocket or a bag. Users can opt to personalize their Always On Watch with customizable, interactive watch faces."
Who's willing to help me test this feature?
Click to expand...
Click to collapse
Someone already posted on the forums about how their AOD wasn't working, and they found out it was because their strap was blocking their wrist from making contact with the sensor. I'm guessing that the heart rate sensor didn't sense a pulse and turned off the screen completely, or some other sensor all together.
Here's the link:
http://forum.xda-developers.com/gear-s3/help/problems-feature-t3507324/page2
My AOD also turns off when the watch determines that I'm sleeping and then requires a security pin.
Sent from my SM-G935P using Tapatalk
optimummind said:
My AOD also turns off when the watch determines that I'm sleeping and then requires a security pin.
Click to expand...
Click to collapse
My AOD works just fine. But it will not turn off when sleeping or covered. It senses my heartbeat just fine. Perhaps my unit is defective? How did you get it to turn it when sleeping, anything special?
Naturesretard said:
My AOD works just fine. But it will not turn off when sleeping or covered. It senses my heartbeat just fine. Perhaps my unit is defective? How did you get it to turn it when sleeping, anything special?
Click to expand...
Click to collapse
Nothing special. My Classic began to track my sleep automatically out of the box. After I wake up, I press a button or rotate the bezel then put in my pin. Shortly afterwards, I get an alert on the watch and it shows in numbers & a graph how long I slept and also shows me how long I was motionless, how long I had a little bit of movement, and how long I was restless.
When the watch is simply covered up by my longsleeve shirt or a jacket, my AOD doesn't turn off.
Sent from my SM-G935P using Tapatalk
It won't turn off AOD with long sleeves, because it knows you're wearing it. It only turns off if it's NOT on your wrist. Or when you're sleeping.
Did anyone install the new PK7 watch update on their Gear S3? Any issues with AOD? Like AOD not working or turning off despite the AOD setting being on?
Sent from my SM-G935P using Tapatalk
I just got my Frontier today, and I came here now looking for answers on the AOD feature i have been hearing about but have not witnessed as of yet... My watch goes completely black every time after about 4 to 5 second of inactivity. Like i said i was coming here now to XDA to find out if this was a config problem or what?? Two things I have seen here that may be an issue for me, 1 - i always wear long sleeve shirts, and 2 - i have always had trouble with the smart watch heart rate monitors getting a good pulse on my wrist. (This is my 5th smartwatch, 4th samsung) I did do all of the updates today when initially using watch. I have been wearing it about 8 hours. Hope this helps.
S1CAR1US said:
I just got my Frontier today, and I came here now looking for answers on the AOD feature i have been hearing about but have not witnessed as of yet... My watch goes completely black every time after about 4 to 5 second of inactivity. Like i said i was coming here now to XDA to find out if this was a config problem or what?? Two things I have seen here that may be an issue for me, 1 - i always wear long sleeve shirts, and 2 - i have always had trouble with the smart watch heart rate monitors getting a good pulse on my wrist. (This is my 5th smartwatch, 4th samsung) I did do all of the updates today when initially using watch. I have been wearing it about 8 hours. Hope this helps.
Click to expand...
Click to collapse
Settings > Style > Always on. Have you turned that on?
Also, it won't work if the watch isn't on your wrist.
Is there a way to increase the brightness of the AOD? Mine is hard to see unless I'm in a fairly dark room.
lyall29 said:
Is there a way to increase the brightness of the AOD? Mine is hard to see unless I'm in a fairly dark room.
Click to expand...
Click to collapse
No, I just kept gesture motion on.
kronium said:
No, I just kept gesture motion on.
Click to expand...
Click to collapse
That's my set up also.
lyall29 said:
Is there a way to increase the brightness of the AOD? Mine is hard to see unless I'm in a fairly dark room.
Click to expand...
Click to collapse
Try Settings, Display, Brightness.
gpmg762 said:
Try Settings, Display, Brightness.
Click to expand...
Click to collapse
Thanks, this does seem to be the only way to make the AOD brighter.
"Samsung Flaunt" is a widget you can install, i installed it on mine (you have to select it from widget once installed) as i found certain faces i have time out into a default (black face white hands and red second hand) i didnt want this, i wanted a face of my selection be it downloaded or a pre-installed face to remain on at all times especially if i go out, if you select the "Frontier" face (pre-installed) and have AOD Turned on you lose very little in quality / dimming when the time out kicks in, with "Samsung Flaunt" you install the widget and this then allows you to have the watch face on for up to 30 mins, However it will eat your battery, but then i can live with day to day charging, I like the idea of going out for a meal or a beer with pals and my face being on, i like the idea of a smart watch simulating a "real" watch look, as we all know there are thousands of faces we can select to show off.
S1CAR1US you can change the time out by going settings/Display/Screen Timeout/ then theres a choice of 15 seconds, 30 seconds, 1 minute or 5 minutes, if you select the desired time out, and go back to your normal face, by clicking your bezel one click left (notifications) and one click right (watch face) your face should remain on for that length of time, if this isn't long enough (wasn't for me) i used the "Samsung Flaunt" widget.
Rgds
Is it possible or not to set automatique disable AOD for exemple every day at 23 h to 07 h ?
[email protected] said:
Is it possible or not to set automatique disable AOD for exemple every day at 23 h to 07 h ?
Click to expand...
Click to collapse
Would be very useful, but it is not possible.
I mean you can't set it in system settings, but it is possible to use a "complication" in Gear Watch Designer.
I designed a couple of watch faces setting a complication to turn off AOD every night, was very simple.
slimsta said:
"Samsung Flaunt" is a widget you can install, i installed it on mine (you have to select it from widget once installed) as i found certain faces i have time out into a default (black face white hands and red second hand) i didnt want this, i wanted a face of my selection be it downloaded or a pre-installed face to remain on at all times especially if i go out, if you select the "Frontier" face (pre-installed) and have AOD Turned on you lose very little in quality / dimming when the time out kicks in, with "Samsung Flaunt" you install the widget and this then allows you to have the watch face on for up to 30 mins, However it will eat your battery, but then i can live with day to day charging, I like the idea of going out for a meal or a beer with pals and my face being on, i like the idea of a smart watch simulating a "real" watch look, as we all know there are thousands of faces we can select to show off.
S1CAR1US you can change the time out by going settings/Display/Screen Timeout/ then theres a choice of 15 seconds, 30 seconds, 1 minute or 5 minutes, if you select the desired time out, and go back to your normal face, by clicking your bezel one click left (notifications) and one click right (watch face) your face should remain on for that length of time, if this isn't long enough (wasn't for me) i used the "Samsung Flaunt" widget.
Rgds
Click to expand...
Click to collapse
Where did u install it from.. Cannot find it in playstore store nor Samsung stire
Sent from my Nexus 6P
I went into samsung gear app/samsung Galaxy apps/searched for flaunt, installed and it should sync to widgets on your s3 gear, hope this helps?
Secret section gear 3
lyall29 said:
thanks, this does seem to be the only way to make the aod brighter.
Click to expand...
Click to collapse
if you guys trying fix all the lil things like brightness and touch and sound go settings_gear info_about device_software version when you infront of this click 5x and that will bring up dialer on there then just press *#0*# from here you can mess with brightness and all sorts of stuff if you figure wat *#0011# will help me out been trying bunch old codes from my s3 s5 days alot work on this lil thing and also if anyone figures out how too turn on dev mode cuz of thizzz pm me thanks....
Hi guys,
Is there really no way to extend the amount of time the cover screen is active? It seems crazy for the display to turn off in the middle of scrolling a notification!
Cheers,
Ffiren
Agree! Not giving the option to "always on" and "timout" limits the z flip by far!!
how has no one came up with a solution for this?!
I would just like the name of the caller - when it switches to answer or reject I can no longer see who I am rejecting...phone in the pocket it's too late at that point. Very frustrating.
Not sure if this is possible, but thought I would ask. I have AOD off (save battery) but would love to have just the yellow notification dot appear when I have an email or text. Anyway to make that happen?
Thanks
ghebb_ns said:
Not sure if this is possible, but thought I would ask. I have AOD off (save battery) but would love to have just the yellow notification dot appear when I have an email or text. Anyway to make that happen?
Thanks
Click to expand...
Click to collapse
Settings -> Cover screen -> Turn on screen for notifications
twistedumbrella said:
Settings -> Cover screen -> Turn on screen for notifications
Click to expand...
Click to collapse
Thanks but does that keep the dot on or just for 15 seconds? What I would like is to be able to look down at my phone (even if I have left it for awhile) and see if I have a message.
I was literally just thinking this! I also have AoD off to save battery. Would love to have a pixel(s) that flash around the screen randomly if/when you have a notification.
Not sure about that. Possibly an app? I don't know that edge lighting is "smart" in that it swaps to the cover.
There are a few apps in the playstore that do this but for regular phones. Will try a couple and see if they can be used on the cover screen
D4rk4 said:
I was literally just thinking this! I also have AoD off to save battery. Would love to have a pixel(s) that flash around the screen randomly if/when you have a notification.
Click to expand...
Click to collapse
Tap on AOD should use very little battery in standby. On my N10+ it's around .5%@hr with internet/phone enabled.
Quiet time is healthy for you... being available 24/7 is no blessing at all. After I go to bed I rarely look at the phone.
Audible/tactile notifications may be an option in standby too.
There's Edge lighting but that was always less than reliable even with the display on
D4rk4 said:
There are a few apps in the playstore that do this but for regular phones. Will try a couple and see if they can be used on the cover screen
Click to expand...
Click to collapse
As long as none of them target a specific display, it should be possible.
Might be worth taking a look at the fold or previous flip to see if they had a solution. Basically any phone that has a cover screen
I found this on the first flip thread:
Notification light in cover display
Hi people, got notification light working on Z Flip with Tasker :) You can modify icon and text its showing. Basically notification of your choice (WA, Telegram, etc. ) triggers it, then Tasker issues notification in every 2 sec. as long as...
forum.xda-developers.com
It is almost one year, since my first Flip 5G, I am trying to find a solution to have a permanent dot notification on outer screen, no party.
Now with Flip 3, same story.
I do not understand why a developer isn't willing to create an app for that.
I would pay and others would do, as me...
Just tap the screen once and you'll see the dot, double tap to fully wake it up.
I wrote "permanent", meaning that the dot is continuously blinking even with screen off in case of a notification.
In the oneui4 release notes it says it can turn the AOD ON when there is a notification. Im hoping that does what it sounds like because I miss this as well.
The app aodnotify works on the Z Flip3, at least enough to be useful.
Basically you set it up so always on display is off unless a notification is received. Then set it so the screen will turn on and stay on for however long you want. That will make the exterior screen turn on (assuming the phone is closed) for the time you set. I set mine to 2 min and it hasn't had any real effect on battery life. If the phone is open then it can still do edge lighting, blinking dot etc on the main display.
If it wasn't for aodnotify I'd never know when I have a notification unless I stared at the phone all day but with the screen staying on for 2 min I usually notice because I'll catch it in my peripheral vision or when I glance at it.
Recently someone posted code to control the exterior display. It's located here..
Cover Screen Support Campaign
Samsung has done it again with the proprietary meta-data and added their own requirements on using apps on the cover screen, not unlike their silly tags for VR and multi-window. Do you use an app that wouldn't cause any privacy concerns on the...
forum.xda-developers.com
I'm hoping @Jawomo (dev of aodnotify) will use it to add support for the z Flip3 and future versions of this phone so we can get edge lighting on the exterior screen.