After using this tool you will have the chinese rom installed. (H2OS = Hydrogen OS)
Instructions how to use can be found: HERE
There is only one difference. To boot into Qualcomm download mode you need to press Volume up + Volume down when phone is powered off.
There is also a guide on YouTube. --> LINK
You can easily go to OxygenOS with official Updater app.
Just download OxygenOS OTA.zip and choose it with updater.
After reboot i personally would factory reset the phone.
Downloadlink MSMTOOL:
MEGA
Thread for OTA.zip:
Oneplus 7 Repo Oxygen OS builds
Feel free to report about your experience!
Thanks:
@Titokhan - for the Update.zip files
@Thyson - for testing the MSM Tool and reporting
@jmax91 - for the tip (tool)
@LloydSmallwood - for the unbrick guide
Finally MsmDownloadTools for our OnePlus 7. Has anyone tried it yet?
Confirmed, an XDA partner has already used it and revived his OnePlus 7 !!!
Link from partner's message:
https://forum.xda-developers.com/showpost.php?p=79989363&postcount=32
Kollachi said:
After using this tool you will have the chinese rom installed. (H2OS = Hydrogen OS)
You can easily go to OxygenOS with official Updater app.
Just download OxygenOS OTA.zip and choose it with updater.
After reboot i personally would factory reset the phone.
Downloadlink MSMTOOL:
MEGA
Thread for OTA.zip:
Oneplus 7 Repo Oxygen OS builds
Note: I didnt test it! @Thyson tried it and reported its working. Feel free to report guys.
Thanks:
@Titokhan - for the Update.zip files
@Thyson - for testing the MSM Tool and reporting
@jmax91 - for the tip (Tool)
Click to expand...
Click to collapse
Hello friend, add to your thread the steps that mark the original link of this MsMDownloadTool:
Link: https://repairmymobile.in/flash/oneplus-7-flash-file/amp/
How to Flash OnePlus 7:
1- Install Qualcomm Driver.
2- Make sure your device getting identified in device manager as Qualcomm HS-USB Diagnostic 9008.
3- Use both Volume as boot key.
4- Run MSM Download tool.
5- Click on verify, if it display message ok then you are ready to go.
6- Click on start to Flash.
7- Download Progress will be displayed.
8- When completed, Download complete will be displayed.
tURkOsANsE said:
1- Install Qualcomm Driver.
2- Make sure your device getting identified in device manager as Qualcomm HS-USB Diagnostic 9008.
3- Use both Volume as boot key.
4- Run MSM Download tool.
5- Click on verify, if it display message ok then you are ready to go.
6- Click on start to Flash.
7- Download Progress will be displayed.
8- When completed, Download complete will be displayed.
Click to expand...
Click to collapse
I think the steps should be clear. It's always the same since OnePlus 3/T. There is only one little different thing.
Kollachi said:
I think the steps should be clear. It's always the same since OnePlus 3/T. There is only one little different thing.
Click to expand...
Click to collapse
Hi friend, what is that different thing you say? Some is the first time we have a OnePlus, so we do not know.
Another question I have is that my OnePlus 7 works fine, but I wanted to see if this program recognizes me my OnePlus in case I ever need it, how can I enter the necessary mode to be detected by this program?
I press volume up and volume down and then I connect the cable, at that moment the program makes me "connected" (see attached image, left side), but after a few seconds it appears that "disconnected" and the phone restarts and OSS starts .
When I connect it, the images "Qualcomm HS-USB QDLoader 9008 (COM3) appear in the device manager.
I do not understand why my mobile when I connect it by pressing the volume buttons and without touching anything of the program it appears that connected and after a few seconds it disconnects itself and OOS restarts.
Regards, and thank you very much.
tURkOsANsE said:
Hi friend, what is that different thing you say? Some is the first time we have a OnePlus, so we do not know.
Another question I have is that my OnePlus 7 works fine, but I wanted to see if this program recognizes me my OnePlus in case I ever need it, how can I enter the necessary mode to be detected by this program?
I press volume up and volume down and then I connect the cable, at that moment the program makes me "connected" (see attached image, left side), but after a few seconds it appears that "disconnected" and the phone restarts and OSS starts .
When I connect it, the images "Qualcomm HS-USB QDLoader 9008 (COM3) appear in the device manager.
I do not understand why my mobile when I connect it by pressing the volume buttons and without touching anything of the program it appears that connected and after a few seconds it disconnects itself and OOS restarts.
Regards, and thank you very much.
Click to expand...
Click to collapse
The different part is you need to press volume up and volume down. With the older phones there was only one button. Don't remember volume up or down.
Not sure why your phone disconnecting automatically.
Kollachi said:
The different part is you need to press volume up and volume down. With the older phones there was only one button. Don't remember volume up or down.
Not sure why your phone disconnecting automatically.
Click to expand...
Click to collapse
Hi friend, could you try if the same thing happens to you?
Made the mistake of locking my bootloader directly and bricked the hell out of my standard 7. I kept getting "Your device is corrupt and it can't be trusted". No Recovery accessible, only bootloader.
Followed the steps here and everything is back to normal now!
GoToNap said:
Made the mistake of locking my bootloader directly and bricked the hell out of my standard 7. I kept getting "Your device is corrupt and it can't be trusted". No Recovery accessible, only bootloader.
Followed the steps here and everything is back to normal now!
Click to expand...
Click to collapse
Hello friend, could you help me to know why when I connect my device appears as connected and after 10 seconds it automatically restarts the OOS operating system? My phone works well, it's just a test to know if one day I have a brick to know that this program works in my case.
I would need (now that your device works, like mine) to start in a way that the program detects and looks "connected", then wait a moment and without pressing any button on the program or phone to see if it restarts alone. I am thinking that if the phone works well, the program when connected only starts the system automatically.
Read some messages above in case I have not explained myself well.
Could someone who has a good phone confirm this? Can the program attempt to automatically restart the device if the "Start" button of MsmDownloadTool is not pressed within 10 seconds?
Thanks greetings.
tURkOsANsE said:
Hi friend, could you try if the same thing happens to you?
Click to expand...
Click to collapse
Yep, same here. Maybe it's because device isn't bricked. I'm not sure about that. Never tried MSMTool when my device wasn't bricked.
Kollachi said:
Yep, same here. Maybe it's because device isn't bricked. I'm not sure about that. Never tried MSMTool when my device wasn't bricked.
Click to expand...
Click to collapse
hello, thanks for trying it, then that happens, if it is not locked it restarts, or maybe the EDL mode restarts for security if you don't press Start on the Msm tool.
---------- Post added at 12:20 PM ---------- Previous post was at 12:10 PM ----------
Indeed we have already resolved the doubt about why EDL mode is disconnected after 10 seconds. It is a security system, you have 10 seconds to press Start. here another partner who has tried it and that happened to him, until he hit start and flashed everything well.
Comrade comment: https://forum.xda-developers.com/showpost.php?p=79997414&postcount=54
tURkOsANsE said:
Hello friend, could you help me to know why when I connect my device appears as connected and after 10 seconds it automatically restarts the OOS operating system? My phone works well, it's just a test to know if one day I have a brick to know that this program works in my case.
I would need (now that your device works, like mine) to start in a way that the program detects and looks "connected", then wait a moment and without pressing any button on the program or phone to see if it restarts alone. I am thinking that if the phone works well, the program when connected only starts the system automatically.
Read some messages above in case I have not explained myself well.
Could someone who has a good phone confirm this? Can the program attempt to automatically restart the device if the "Start" button of MsmDownloadTool is not pressed within 10 seconds?
Thanks greetings.
Click to expand...
Click to collapse
I see that you sent a private message to me also and mentioned that you got into the Bootloader. That is not what you need.
First of all, you will need to install the qualcom drivers from here: https://www.androidjungles.com/qualcomm-hs-usb-qdloader-9008-driver-64-bit-windows/
Afterwards, you will need to hold both volume buttons, and after a few seconds connect your phone to the computer via cable (while still holding the volume buttons).
The phone will be detected as a Qualcom device and you cand start following the tutorial that was provided earlier.
GoToNap said:
I see that you sent a private message to me also and mentioned that you got into the Bootloader. That is not what you need.
First of all, you will need to install the qualcom drivers from here: https://www.androidjungles.com/qualcomm-hs-usb-qdloader-9008-driver-64-bit-windows/
Afterwards, you will need to hold both volume buttons, and after a few seconds connect your phone to the computer via cable (while still holding the volume buttons).
The phone will be detected as a Qualcom device and you cand start following the tutorial that was provided earlier.
Click to expand...
Click to collapse
Hello friend, I already managed to enter the EDL mode correctly, the doubt is that when I connected it after 10 seconds, the phone disconnected and relapsed. That's why I said that if I could test now that your phone works, it also automatically restarts without touching any Msm program button once connected in EDL mode.
Something with EDL mode in OP7 is currently wrong.
As the predecessors wrote, after connecting, it is interrupted after a few seconds and the phone reboots.
I also have OP3, OP6 in them after the EDL mode is switched on the connection is maintained all the time.
Andro_Nicus said:
Something with EDL mode in OP7 is currently wrong.
As the predecessors wrote, after connecting, it is interrupted after a few seconds and the phone reboots.
I also have OP3, OP6 in them after the EDL mode is switched on the connection is maintained all the time.
Click to expand...
Click to collapse
That's what @Thelargeportion wrote at OP7Pro thread:
"Yes, it did on mine. I've just used this tool to recover from root to stock.
Noted that if the program isn't started within 10 seconds, the phone rebooted automatically, I'm guessing as some sort of security lock. Restarted in EDL, connected to the MSMDownloadtool and executed the program as soon as it was connected and it flashed absolutely fine.
Note that after the phone is restarted after a successful flash, it takes about 1-2 minutes to boot again having stuck on the OnePlus boot logo."
Could be true. But nevermind... It works and that's important.:laugh:
Yes, it is the most important thing that it flashes the system image.
However, it does not maintain a permanent session in EDL as
in previous OnePlus models, and that may be worrying.
Andro_Nicus said:
Yes, it is the most important thing that it flashes the system image.
However, it does not maintain a permanent session in EDL as
in previous OnePlus models, and that may be worrying.
Click to expand...
Click to collapse
I can Tell you, after days with a bricked Phone and seeking for a Tool. You really don't Care about permanent Sessions.
Regrads
Thyson
If something works differently, it usually is always puzzling.
That is why all these posts appeared on this subject.
Andro_Nicus said:
If something works differently, it usually is always puzzling.
That is why all these posts appeared on this subject.
Click to expand...
Click to collapse
Hello friend, yes, that happens to all of us, it is not an isolated case, but if once you enter EDL mode and connect the phone to the PC and it appears "connected", you press start and everything works. You must press start in 10 seconds since entering EDL mode, once you press start, it no longer restarts and blinks correctly.
This of the 10 seconds occurs in all OnePlus 7 series (normal and PRO).
Comment where I ask about 10 seconds and colleagues confirm that they used the tool: https://forum.xda-developers.com/showpost.php?p=79997414&postcount=54
Related
I was trying to flash BlissPop. It didn't flash. So, I decided to flash fastboot image of CM11s 44.
I issued this command :
Code:
fastboot flash modem NON-HLOS.bin
fastboot reboot-bootloader
fastboot flash sbl1 sbl1.mbn
fastboot reboot-bootloader
The flash sbl1 command gave an error.
I rebooted bootloader. The phone turned off, but it never turned on.
I don't know how could it brick my phone, because I've done it a few times without any error.
My battery was on 65% when I was doing all this. So, I don't suspect battery has died.
But, I'm charging the phone anyway. There is no lead, but the power bank shows that battery is taking charge.
When I connect the phone to PC, it shows no signs of any device connected. Device manager doesn't show any thing/any refresh.
I've tried to push the power button for about a minute for 5 times, as 1+1 site says.
I've tried vol up + power and vol down + power buttons. It doesn't boot it.
I've no access to fastboot, recovery, OS, anything.
Please, suggest me solutions.
Did you flash the firmware updates before you flashed bliss? There is a toolkit out there, linked in bliss thread, on how to unbrick. I'll see if I can't find it.
Sent from my A0001 using Tapatalk
---------- Post added at 11:49 PM ---------- Previous post was at 11:45 PM ----------
http://forum.xda-developers.com/showthread.php?p=58230647
First look at this perhaps. If not there is a toolkit out there to flash back to stock. Should be able to communicate w the phone if it can turn on at all.
Sent from my A0001 using Tapatalk
http://forum.xda-developers.com/showthread.php?p=58230647
First look at this perhaps. If not there is a toolkit out there to flash back to stock. Should be able to communicate w the phone if it can turn on at all.
Click to expand...
Click to collapse
Thanks. I looked at it.
But, as you said I can't do anything till the phone turns on even once.
BTW, I highly suspect battery drain, because I was in TWRP for long to take backup, flashing MultiROM, etc. TWRP is known to not allow charging, as reported by some people.
Can you tell me whether flashing sbl1 could have bricked it or not? It didn't fail to flash in past and it never caused problem.
I had flashed CM12 firmware update before flashing BlissPop. Could reflashing CM11s fastboot image over it cause problem. I think it should not, because fastboot image replace all things. What's your opinion?
Had the same problem. Try first leave it charging for 12 hours after that plug it in. Then get into fastboot this is not easy. Just hold vol up and power together for atv least 5 Sec.
Sent from my A0001 using XDA Free mobile app
I guess its possible. But I would do what falastine said. Charge it for some time. With a soft brick it may not show anything on the screen but could actually be on. So be patient trying to get the toolkit to find the phone. I've heard in another thread someone's phone did in fact connect but nothing was on the screen
Sent from my A0001 using Tapatalk
any progress on this? i think the exact same thing happened to me. was trying to flash back to CM11s using fastboot, but it died. now i dont get anything at all. no response to the chrager, or the computer or anything.
ive tried holding the power button, holding the vol keys with the pwr button, but no avail.
let me know if you figured it out!
Falastine said:
Had the same problem. Try first leave it charging for 12 hours after that plug it in. Then get into fastboot this is not easy. Just hold vol up and power together for atv least 5 Sec.
Sent from my A0001 using XDA Free mobile app
Click to expand...
Click to collapse
I left the phone in charge for 24 hours using original charger and wire.
Tried long presses for multiple times - nothing happens.
Tried vol up/ vol down combinations with power button for long nothing happens.
I am now waiting for 12 hours and then will plug it again, as some thread said.
In between I'm trying to download a tool from here : http://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851
I hope it detects my phone.
hassan3216 said:
any progress on this? i think the exact same thing happened to me. was trying to flash back to CM11s using fastboot, but it died. now i dont get anything at all. no response to the chrager, or the computer or anything.
ive tried holding the power button, holding the vol keys with the pwr button, but no avail.
let me know if you figured it out!
Click to expand...
Click to collapse
There is no progress.
It appears that we are in same situation.
I highly suspect dead battery, instead of dead phone. Anyway, I'll post updates.
Please, share if anything works for you.
I had the same problem and had to restore the phone with this tool:
https://forums.oneplus.net/threads/...ol-restore-stock-cm11s-fix-bricks-etc.237827/
I had many problems with the drivers and i had tot install the qualcom drivers http://sciencespaces.com/search/Qualcomm+HS-USB+Android+DIAG+9018/
The topic said that there is an issue with the modem and you have tot flash it manually but i don't have problems so far.
michaeldepotter said:
I had the same problem and had to restore the phone with this tool:
https://forums.oneplus.net/threads/...ol-restore-stock-cm11s-fix-bricks-etc.237827/
I had many problems with the drivers and i had tot install the qualcom drivers http://sciencespaces.com/search/Qualcomm+HS-USB+Android+DIAG+9018/
The topic said that there is an issue with the modem and you have tot flash it manually but i don't have problems so far.
Click to expand...
Click to collapse
@michaeldepotter
Thanks for writing here.
I'm following the thread mentioned by you.
But, the problem is that I don't know how to get the phone in Qualacom mode.
I don't whether my phone is on or off. So, I've tried to connect it with PC and pressing key mentioned in the thread. It didn't work.
If you could share your experience with me, it will be kind of you.
I've windows 8.1 64 bit.
I'm at work now but in a couple of hours i can give you more info how i did it
Sent from my A0001 using XDA Free mobile app
michaeldepotter said:
I'm at work now but in a couple of hours i can give you more info how i did it
Sent from my A0001 using XDA Free mobile app
Click to expand...
Click to collapse
@michaeldepotter,
Sure, no problem.
I'll be eagerly waiting.
mahastat said:
@michaeldepotter
Thanks for writing here.
I'm following the thread mentioned by you.
But, the problem is that I don't know how to get the phone in Qualacom mode.
I don't whether my phone is on or off. So, I've tried to connect it with PC and pressing key mentioned in the thread. It didn't work.
If you could share your experience with me, it will be kind of you.
I've windows 8.1 64 bit.
Click to expand...
Click to collapse
open your device manager in your pc and use volume up and power button while connected to pc to get into qualcom mode.most probably it would be detected as android fastboot interface just click on it and update the driver to qualcom usb serial interface then use http://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851 this tool to recover
wilbur2brooks said:
open your device manager in your pc and use volume up and power button while connected to pc to get into qualcom mode.most probably it would be detected as android fastboot interface just click on it and update the driver to qualcom usb serial interface then use http://forum.xda-developers.com/oneplus-one/general/tool-oneplusrecovery-tool-v1-0-restore-t2991851 this tool to recover
Click to expand...
Click to collapse
@wilbur2brooks
Thanks for writing.
I could understand that once my phone is detected as even unknown device, I can install drivers and try to recover through the tool you mentioned.
But, the problem is that my phone is not recognized as anything. The Device Manager shows no reaction when I connect the phone to computer.
I have disabled driver signature on my Windows 8.1 64 bit. I've Qualacom drivers installed. Rebooted computer in disabled signature mode.
I've connected my device through official cable and I've tried the key combination mentioned.
My other devices show up when connected to PC, but 1+1 doesn't.
Any other thing which I could try.
I had left my phone in charging for 24 hours, but it doesn't wake it up.
Any suggestion is appreciated.
mahastat said:
@michaeldepotter
Thanks for writing here.
I'm following the thread mentioned by you.
But, the problem is that I don't know how to get the phone in Qualacom mode.
I don't whether my phone is on or off. So, I've tried to connect it with PC and pressing key mentioned in the thread. It didn't work.
If you could share your experience with me, it will be kind of you.
I have windows 8.1 64 bit.
Click to expand...
Click to collapse
So this is how i did it.
1. install the drivers from OPO (located in the .zip file from this tool https://forums.oneplus.net/threads/t...ks-etc.237827/ )
2. Open your device manager (Start - right click on computer - properties - devices manager)
3. Press on power + vol up for like 10 sec until you see a device showing up (called QHSUSB_BULK)
4. Download the qualcomdriver ( https://www.dropbox.com/s/vgujdut93m341qm/Qualcomm 2012.rar?dl=0 ). Right click on this devices and click on "Update Driver Software" -> "Browse my computer for driver software" -> locate the Qualcomm 2012\fre\Windows7 8 or vista folder depending on your setup. Update the driver.
5. Now the OPO tool should recognize your device. I turn off all my network connections so the usb device can't find other drivers. (in case windows overwrite the driver).
---------- Post added at 07:29 PM ---------- Previous post was at 07:07 PM ----------
Have you tried another PC?
Sent from my A0001 using XDA Free mobile app
michaeldepotter said:
So this is how i did it.
1. install the drivers from OPO (located in the .zip file from this tool https://forums.oneplus.net/threads/t...ks-etc.237827/ )
2. Open your device manager (Start - right click on computer - properties - devices manager)
3. Press on power + vol up for like 10 sec until you see a device showing up (called QHSUSB_BULK)
4. Download the qualcomdriver ( https://www.dropbox.com/s/vgujdut93m341qm/Qualcomm 2012.rar?dl=0 ). Right click on this devices and click on "Update Driver Software" -> "Browse my computer for driver software" -> locate the Qualcomm 2012\fre\Windows7 8 or vista folder depending on your setup. Update the driver.
5. Now the OPO tool should recognize your device. I turn off all my network connections so the usb device can't find other drivers. (in case windows overwrite the driver).
---------- Post added at 07:29 PM ---------- Previous post was at 07:07 PM ----------
Have you tried another PC?Sent from my A0001 using XDA Free mobile app
Click to expand...
Click to collapse
The hard part is that I could not get the phone detected by PC as anything.
I followed the same key combination which you mentioned. It doesn't help.
Can you tell me if battery is totally depleted, will it be possible for phone to be detected?
I've tried to charge my phone with various chargers and power banks. The battery stays cold, the charger stays cold, power bank blinks and get depleted, but phone is not vibrating even on long press.
I've tried on virtual PC, a XP machine. And on other real XP PC.
Thanks for your help.
If you have some more suggestions based on information given by me, kindly post it again.
mahastat said:
@wilbur2brooks
Thanks for writing.
I could understand that once my phone is detected as even unknown device, I can install drivers and try to recover through the tool you mentioned.
But, the problem is that my phone is not recognized as anything. The Device Manager shows no reaction when I connect the phone to computer.
I have disabled driver signature on my Windows 8.1 64 bit. I've Qualacom drivers installed. Rebooted computer in disabled signature mode.
I've connected my device through official cable and I've tried the key combination mentioned.
My other devices show up when connected to PC, but 1+1 doesn't.
Any other thing which I could try.
I had left my phone in charging for 24 hours, but it doesn't wake it up.
Any suggestion is appreciated.
Click to expand...
Click to collapse
Even if your battery is depleted it should get detected in your machine when u press volume up and power while its connected to your pc.hold it for a minute this combination should show something also keep your pc volume up to hear any port connect discconect sounds.If this doesnt happen then your hardware is dead no other option but try to give it to opo for service.
So, nothing ever comes on the screen? Does the phone vibrate if you hold the power button for 20 seconds? If so, this might be of help, if it sounds like it's bricked: http://forum.xda-developers.com/oneplus-one/help/guide-unbrick-oneplus-one-t3013732
wilbur2brooks said:
Even if your battery is depleted it should get detected in your machine when u press volume up and power while its connected to your pc.hold it for a minute this combination should show something also keep your pc volume up to hear any port connect discconect sounds.If this doesnt happen then your hardware is dead no other option but try to give it to opo for service.
Click to expand...
Click to collapse
I've PC volume UP, device manager in front and phone connect. Key combination brings nothing.
So, I think I'll take it to OPO Service Center now.
Thanks for helping me.
netbuzz said:
So, nothing ever comes on the screen? Does the phone vibrate if you hold the power button for 20 seconds? If so, this might be of help, if it sounds like it's bricked: http://forum.xda-developers.com/oneplus-one/help/guide-unbrick-oneplus-one-t3013732
Click to expand...
Click to collapse
Nothing comes on screen, no vibrations. It's bricked.
Going to OPO Service Center.
Thanks for looking after my problem.
I appreciate all who took part in this thread to help me. Thanks.
Moderators may close this thread now.
Please Help Me!:crying:
My 7 Pro has been bricked.
circumstance：
i press VolUp + Power for a while, there are showed <!> screen (= warn for unlocking) only a few seconds.
but fastboot screen is not displayed. black out.
of course, recovery is the same. (black out)
if i connect 7 Pro to a PC, there is a response for a moment, but it does not appear in the device manager (similar things appear in the "Port").
when i flashed
OnePlus7ProOxygen_21.E.15_OTA_015_all_1907281610_e735c0c31ada4eee.zip
and
Magisk-v19.4.zip
from TWRP, It became current state after this operation.
This is the first time such a brick.
Does anyone have the same situation or have a solution?
MtnOrf said:
Please Help Me!:crying:
My 7 Pro has been bricked.
circumstance：
i press VolUp + Power for a while, there are showed <!> screen (= warn for unlocking) only a few seconds.
but fastboot screen is not displayed. black out.
of course, recovery is the same. (black out)
if i connect 7 Pro to a PC, there is a response for a moment, but it does not appear in the device manager (similar things appear in the "Port").
when i flashed
OnePlus7ProOxygen_21.E.15_OTA_015_all_1907281610_e735c0c31ada4eee.zip
and
Magisk-v19.4.zip
from TWRP, It became current state after this operation.
This is the first time such a brick.
Does anyone have the same situation or have a solution?
Click to expand...
Click to collapse
MSMDownload Tool.
That will get you back to a fresh OS.
MtnOrf said:
Please Help Me!:crying:
My 7 Pro has been bricked.
circumstance：
i press VolUp + Power for a while, there are showed <!> screen (= warn for unlocking) only a few seconds.
but fastboot screen is not displayed. black out.
of course, recovery is the same. (black out)
if i connect 7 Pro to a PC, there is a response for a moment, but it does not appear in the device manager (similar things appear in the "Port").
when i flashed
OnePlus7ProOxygen_21.E.15_OTA_015_all_1907281610_e735c0c31ada4eee.zip
and
Magisk-v19.4.zip
from TWRP,It became current state after this operation.
This is the first time such a brick.
Does anyone have the same situation or have a solution?
Click to expand...
Click to collapse
I actually also bricked mine today and also had to use the msm download tool.
It was fairly easy and I was happy with the process.
No worries ?
tech_head said:
MSMDownload Tool.
That will get you back to a fresh OS.
Click to expand...
Click to collapse
Device manager shows "Qualcomm HS-USB Diagnostics 900E(COM5)".
so(?) there are no responses in MSM tool.
schorrie said:
I actually also bricked mine today and also had to use the msm download tool.
It was fairly easy and I was happy with the process.
No worries
Click to expand...
Click to collapse
thanks.
but, ,my device manager shows "Qualcomm HS-USB Diagnostics 900E(COM5)".
so(?) there are no responses in MSM tool.
Do I need to use an EDL cable...?
I had this exact same problem last night. Plug it in via USB and make sure you have volume on your speakers. Press and hold volume up, down and power and for some reason the bootloader will come up. Pick power off, then press volume up and down at the same time and plug your USB cable into the phone and listen for the connection sound.
Hi, apparently I deleted too much from twrp recovery. Now the phone doesn't shwitch on even.
Only when I hold "Volume up" an press "Power" for some time, the device shows a reaction. it sort of boots up but only shows the warning about "Bootloader unlocked". Then after few seconds it shwitches off again.
When I plug it by USB into a computer, the computer identifies a
"Qualcomm HS-USB Diagnostics 900E".
What can I do to unbrick my device?
Many thanks in advance for any tips or pointers!
Msm download tool. Works like a charm. You will lose everything but if you can't even get into the phone, sounds like it is already lost.
GeekMcLeod said:
Msm download tool. Works like a charm. You will lose everything but if you can't even get into the phone, sounds like it is already lost.
Click to expand...
Click to collapse
sounds interesting; where would I get that tool?
In the meantime I found another solution: Hold Volume Up and Volume Down pressed at the same time and press Power until the System boots up. Voila, fastboot mode running.
heinerich said:
sounds interesting; where would I get that tool?
In the meantime I found another solution: Hold Volume UpandVolume Down pressed at the same time and press Power until the System boots up. Voila, fastboot mode running.
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691
Follow instructions and it should bring you back to 9.5.something. I recommend updating to A10 before root and twrp, it's what I did and everything worked out good.
Hi,
I'm having troubles after following the guide here - https://wiki.lineageos.org/devices/guacamole/install
I initially had stock Android 11 with latest update. I've followed the instructions, all went well until I rebooted to system. It just tries to boot for a few minutes, then it restarts and does this again. Doesn't seem to boot.
Is there a way to fix this?
Also, would be possible to get back to stock rom and how?
Thank you in advance!
Managed to fix, in the end. Was a real headache.
If anyone is having similar problem and they have to unbrick their phone, I suggest this thread - https://forum.xda-developers.com/t/...l-to-restore-your-device-to-oxygenos.3954325/
Follow the steps in that thread. To enter EDL mode, you will have to turn off your device, hold Volume UP and Volume down (without power button) and while holding insert the USB cable into the phone and into your PC. By doing so, it will be detected by the computer and will show up in Device Manager.
The most annoying issue I had was the phone was connecting for a few seconds, then disconnect. What worked for me after many many tries was using a newer image, mine being an international device I used 10.3.8. I opened MSM from the 10.3.8 package and Device Manager, connected the cable to the computer, but not to the phone, I've pressed volume up and down, connected the cable to the phone while holding volume buttons and as soon as Qualcom driver showed up in Ports (COM & LPT), I hit start on MSM.
If it still gives you the error "Sahara Communication Failed. Please try again after power off phone" try with a different package version, for me this one worked, but before that I've tried with a different one and I was getting this error.
Hope it will help someone, at some point. I know how frustrating it is and if I helped you be less frustrated than I was, that's a win.
When I used the Fastboot Enhance tool to flash the payload.bin file, after the flash process finished I try to reboot but unfortunately it was dead.
No Fastboot, no EDL, no recovery, 3 buttons not working, power with up/down not working, when i connect to PC no sound that the pc recognize the phone "OP 8T", when I plug it into charger no info showing, Just black screen.
So it's working now, I'll explain everything here so it might help.
My device is OnePlus 8T DDR5 version
first, I understand what happened to me, I think the tool didn't recognize ram type automatically so it was flash DDR4 on a DDR5 device, so it made a hard brick
at this point, the idea is to connect 2 test points, and you can force your phone to enter to EDL mode, and we can do it in two ways:
1. Rootk1t giude, thax bro Rootk1t
- Removing the back panel by heating it.
- Unplugging battery
- Then use the EDL points on the motherboard to force the device to boot EDL.
- The device immediately will be recognised with just one tap on "enum" now.
- Plugging the battery again and attaching the back panel and rebooting
2. By using deep EDL cable, but not any edl cable, it must be a moded cable so it can be worked with the new security ...... this link will explain
Hydra Tool Gift Xiaomi, Huawei, Redmi Qualcomm EDL Mode New V2 Cable!! - GSM-Forum
Hydra Tool Gift Xiaomi, Huawei, Redmi Qualcomm EDL Mode New V2 Cable!! Hydra Tool New Type-C EDL cable Schematic With this cable you can reboot your
forum.gsmhosting.com
- So i use Hydra EDL Cble V2 , you can buy it from aliexpress
- Be ready and open your MSM tool
- Press the cable button before connecting
- Connect the cable to your phone when you still pressing the button
- Then connect the USB to your PC
- It will automatically put your phone in EDL mode
- Now your phone will show in the MSM tool screen so you can revive it.
Thanks to everyone who tried to help.
Special thanks to Rootk1t , semdoc
Abdo Ismail said:
when I used the Fastboot Enhance tool to flash the payload.bin file, after the flash process finished I try to reboot but unfortunately it was dead.
No Fastboot, no EDL, no recovery, 3 buttons not working, power with up/down not working, when i connect to PC no sound that the pc recognize the phone "OP 8T", when I plug it into charger no info showing, Just black screen.
I don't know what should i do, please anyone help me with this problem.
Thanks in advance
Click to expand...
Click to collapse
Are you sure no EDL? Did you try the msm tool to restore to factory settings?
JedidroidX said:
Are you sure no EDL? Did you try the msm tool to restore to factory settings?
Click to expand...
Click to collapse
I'm sure, and I try MSM , the phone can't connect anymore to PC
Abdo Ismail said:
I'm sure, and I try MSM , the phone can't connect anymore to PC
Click to expand...
Click to collapse
Seem like you flashed the wrong xml for the ram type. There is one for ddr4 and ddr5. If EDL is not working I'm afraid according to several post it's an unrecoverable brick...sorry mate!!!
However keep searching for a solution, you never know maybe a new method of recovery from this disaster may exist. I'll keep searching and if I find anything I'll post it here!
Also have you tried the 3 buttons connected from charger and disconnected? Usually for some reason my phone won't respond with the 3 buttons when connected to usb sometimes.
Also have you used the msm tool before?
JedidroidX said:
Seem like you flashed the wrong xml for the ram type. There is one for ddr4 and ddr5. If EDL is not working I'm afraid according to several post it's an unrecoverable brick...sorry mate!!!
However keep searching for a solution, you never know maybe a new method of recovery from this disaster may exist. I'll keep searching and if I find anything I'll post it here!
Also have you tried the 3 buttons connected from charger and disconnected? Usually for some reason my phone won't respond with the 3 buttons when connected to usb sometimes.
Also have you used the msm tool before?
Click to expand...
Click to collapse
Thanks bro for your cooperation, yes i tried everything and yes i used MSM tool a lot of time.
i'll searh more to fix this prob, thx again
Abdo Ismail said:
Thanks bro for your cooperation, yes i tried everything and yes i used MSM tool a lot of time.
i'll searh more to fix this prob, thx again
Click to expand...
Click to collapse
Just one more thing, when you connect the phone to pc check your device manager to see if the PC reads the phone. If it does than its just a driver issue and reinstalling the qualcom driver for msm maybe needed.
I've found that sometimes I have to reinstall the Qualcomm drivers for EDL. So check that when you connect the phone to the PC in EDL mode there isn't an entry in Device Manager under Ports (COM & LPT)
JedidroidX said:
Just one more thing, when you connect the phone to pc check your device manager to see if the PC reads the phone. If it does than its just a driver issue and reinstalling the qualcom driver for msm maybe needed.
Click to expand...
Click to collapse
when I connect it to PC I can't hear the sound which appears when you connect a new device, and also no changes in the device manager unfortunately
BillGoss said:
I've found that sometimes I have to reinstall the Qualcomm drivers for EDL. So check that when you connect the phone to the PC in EDL mode there isn't an entry in Device Manager under Ports (COM & LPT)
Click to expand...
Click to collapse
I can't know which mode the phone is stuck on, because I have only a black screen, even the Power button with volume up / down not working,
do you think if I keep it for a couple of days the battery will drain and I can use MSM tool with press 2 volume buttons, it's the last thing i think about
Abdo Ismail said:
I can't know which mode the phone is stuck on, because I have only a black screen, even the Power button with volume up / down not working,
do you think if I keep it for a couple of days the battery will drain and I can use MSM tool with press 2 volume buttons, it's the last thing i think about
Click to expand...
Click to collapse
I would open it up and remove the battery instead of waiting for days but that's also an option. It's not that hard to open, I opened mines to replace the usb port. I just held the back of the bottom corners of the phone over the stove until it was hot enough to soften the glue and used an old credit card and my thumb nail to open it. It maybe unrecoverable anyway so its worth a try.
JedidroidX said:
I would open it up and remove the battery instead of waiting for days but that's also an option. It's not that hard to open, I opened mines to replace the usb port. I just held the back of the bottom corners of the phone over the stove until it was hot enough to soften the glue and used an old credit card and my thumb nail to open it. It maybe unrecoverable anyway so its worth a try.
Click to expand...
Click to collapse
yes, I thought to do that, so I keep it to be the last option, I'm still searching for any new ideas.
bro, really I want to thank you for supporting me, I appreciate that
Abdo Ismail said:
I can't know which mode the phone is stuck on, because I have only a black screen, even the Power button with volume up / down not working,
do you think if I keep it for a couple of days the battery will drain and I can use MSM tool with press 2 volume buttons, it's the last thing i think about
Click to expand...
Click to collapse
I've had a totally black screen at times in Qualcomm Crashdump Mode. To get out of it you can use Power+Vol up and then, when the phone buzzes, use the key combination for bootloader or MSM.
BillGoss said:
I've had a totally black screen at times in Qualcomm Crashdump Mode. To get out of it you can use Power+Vol up and then, when the phone buzzes, use the key combination for bootloader or MSM.
Click to expand...
Click to collapse
I tried a lot to press Volume Up + Power & Volume Down + Power & the 3 buttons, but with no response.
I can't feel any buzz, even I tried it when the phone connected to the PC, no sound come from PC prove that the phone is connected
Please keep us updated with any current queries or resolution as I'm very interested in the outcome.
Thank you!
Abdo Ismail said:
when I used the Fastboot Enhance tool to flash the payload.bin file, after the flash process finished I try to reboot but unfortunately it was dead.
No Fastboot, no EDL, no recovery, 3 buttons not working, power with up/down not working, when i connect to PC no sound that the pc recognize the phone "OP 8T", when I plug it into charger no info showing, Just black screen.
I don't know what should i do, please anyone help me with this problem.
Thanks in advance
Click to expand...
Click to collapse
Hello!
If waiting for battery to discharge will not help you, i suggest of:
- Removing the back panel by heating it.
- Unplugging battery
- Then using the EDL points on the motherboard to force the device to boot EDL.
-The device immediately will be recognised by just one tap on "enum" now.
- Plugging the battery again and attaching back panel and rebooting.
JedidroidX said:
Please keep us updated with any current queries or resolution as I'm very interested in the outcome.
Thank you!
Click to expand...
Click to collapse
sure my bro
Rootk1t said:
Hello!
If waiting for battery to discharge will not help you, i suggest of:
- Removing the back panel by heating it.
- Unplugging battery
- Then using the EDL points on the motherboard to force the device to boot EDL.
-The device immediately will be recognised by just one tap on "enum" now.
- Plugging the battery again and attaching back panel and rebooting.
Click to expand...
Click to collapse
thanks my friend for your suggestion, yes I was thinking about this solution, but I keep it to be the last one, I think I will try this method at the weekend as I'm busy with work these days.
I'll tell you after I try this solution.
Thanks for your cooperation
JedidroidX said:
Seem like you flashed the wrong xml for the ram type. There is one for ddr4 and ddr5.
Click to expand...
Click to collapse
I have the same problem now after trying to downgrade to OOS12
I used this, EU version, I cant find another version, which would have been the right one?
https://oxygenos.oneplus.net/4668_sign_KB2003_11_C_OTA_1360_all_86c2c1_01000100.zip
It installed, but now I cant start the ohone in any way.
Any tipps? Did it work for you Abdo Ismail?
SamNeuer said:
I have the same problem now after trying to downgrade to OOS12
I used this, EU version, I cant find another version, which would have been the right one?
https://oxygenos.oneplus.net/4668_sign_KB2003_11_C_OTA_1360_all_86c2c1_01000100.zip
It installed, but now I cant start the ohone in any way.
Any tipps? Did it work for you Abdo Ismail?
Click to expand...
Click to collapse
Similar case
[OP8T][OOS KB05AA/BA/DA] Unbrick tool to restore your device to OxygenOS
Disclaimer: By attempting any of the processes listed in this thread you accept full responsibility for your actions. I will not be held responsible if your device stops working, catches fire, or turns into a hipster and claims to have been...
forum.xda-developers.com
Rootk1t said:
Hello!
If waiting for battery to discharge will not help you, i suggest of:
- Removing the back panel by heating it.
- Unplugging battery
- Then using the EDL points on the motherboard to force the device to boot EDL.
-The device immediately will be recognised by just one tap on "enum" now.
- Plugging the battery again and attaching back panel and rebooting.
Click to expand...
Click to collapse
Thank you so much for this, after spending 16$ on a stupid edl cable that never worked, your guide revived my op8t I appreciate you!