Database Info

[Q] [NEED HELP] How to restore stock ROM to Moto G (Please read desc)

Hi,
I have messed around with my rooted Moto G and edited build.props. I turned on my phone and a message came up saying "error system.ui has stopped"' this message kept repeating every time I pressed OK.
After failing to fix it, I went onto my recovery and wiped the storage, cache and dalvik. Obviously now when I turn on the phone it just stays on the boot image and nothing happens.I put the phone into fast boot by holding power and vol down, then tried to flash 4.4.2 Stock ROM to my phone but all CMD says is "waiting for device". I'm not sure what to do from here.
Can anyone help me at all? I've already posted before but no one seems to help me.
If you need any screenshots etc I will add them
Thanks,
Matt

@barky02
what are you using to try and install your stock rom? are you just in command prompt terminal or using a program?
anyway,,, your phone needs to be in fastboot mode to be able to run adb commands

hhp_211 said:
@barky02
what are you using to try and install your stock rom? are you just in command prompt terminal or using a program?
anyway,,, your phone needs to be in fastboot mode to be able to run adb commands
Click to expand...
Click to collapse
@hhp_211
@Martin3lli
I'm using CMD, and I was following this guide: http://forum.xda-developers.com/showthread.php?t=2542219
I am unsure how to put my phone into fastboot mode, can you show me how? I put the phone into fast boot by holding power and vol down, and thats how I tried to flash the ROM. all command prompt was saying was <waiting for device>
Thanks,
Matt

barky02 said:
I'm using CMD, and I was following this guide: http://forum.xda-developers.com/showthread.php?t=2542219
@hhp_211
I am unsure how to put my phone into fastboot mode, can you show me how?
Thanks,
Matt
Click to expand...
Click to collapse
When your phone is off, push volume down and power button simultaneously for a few seconds, then it should start fastboot. Plug in your USB cable and proceed with other steps as guide says.

Martin3lli said:
When your phone is off, push volume down and power button simultaneously for a few seconds, then it should start fastboot. Plug in your USB cable and proceed with other steps as guide says.
Click to expand...
Click to collapse
@Martin3lli
Sorry I misunderstood, I did put my phone into fastboot but it still didn't work, I updated my previous reply with the details

try this
I don't know if this will work, this is my threat. Hope it helps
http://forum.xda-developers.com/moto...t1032-t2814093

Saphire007 said:
I don't know if this will work, this is my threat. Hope it helps
http://forum.xda-developers.com/moto...t1032-t2814093
Click to expand...
Click to collapse
Thank youu :3
404 error? is it the right link?

I assume you are trying to run "flashall.bat"?
in the command prompt try this
adb kill-server
then type
adb start-server
then try running the commands...
I believe you are a full xt1028 Verizon phone?
I know what I do for 4.4.2 is using the file
CFC-fastboot_falcon_verizon_user_4.4.2_KXB20.9-1.10-1.20_22_release-keys.xml.zip
un-zip [extract] that file,,,
then make sure you copy and paste from the "/windows" folder in the zip
fastboot.exe
AdbWinApi.dll
cAdbWinUsbApi.dll
into the main folder [where your .bat file is]
with phone connected to pc...
then open it up and double click on the .bat file
CFC-fastboot_falcon_verizon_user_4.4.2_KXB20.9-1.10-1.20_22_release-keys.bat
and it will do all the necessary work
.

hhp_211 said:
I assume you are trying to run "flashall.bat"?
in the command prompt try this
adb kill-server
then type
adb start-server
then try running the commands...
I believe you are a full xt1028 Verizon phone?
I know what I do for 4.4.2 is using the file
CFC-fastboot_falcon_verizon_user_4.4.2_KXB20.9-1.10-1.20_22_release-keys.xml.zip
un-zip [extract] that file,,,
then make sure you copy and paste from the "/windows" folder in the zip
fastboot.exe
AdbWinApi.dll
cAdbWinUsbApi.dll
into the main folder [where your .bat file is]
with phone connected to pc...
then open it up and double click on the .bat file
CFC-fastboot_falcon_verizon_user_4.4.2_KXB20.9-1.10-1.20_22_release-keys.bat
and it will do all the necessary work
.
Click to expand...
Click to collapse
I have an english phone, none of the things you have said were in the tutorial, and the xml I am using doesn't come with any of those, only mfastboot.exe
I don't think my PC is recognising my Moto G properly. On the fastboot screen it says USB connected, but in my devices my phone is called "Fastboot Falcon S"

barky02 said:
I have an english phone, none of the things you have said were in the tutorial, and the xml I am using doesn't come with any of those, only mfastboot.exe
I don't think my PC is recognising my Moto G properly. On the fastboot screen it says USB connected, but in my devices my phone is called "Fastboot Falcon S"
Click to expand...
Click to collapse
Yes you have a Verizon Moto G Right [XT1028]? not a converted Boost Mobile [XT1031]?
what is the name of the zip file you have?

hhp_211 said:
Yes you have a Verizon Moto G Right [XT1028]? not a converted Boost Mobile [XT1031]?
what is the name of the zip file you have?
Click to expand...
Click to collapse
I have a T-Mobile Moto G XT1032
The Zip file name is: EE-GB-SL_FALCON_KLB20.9-1.10-1.24-1.1_cid7_CFC_1FF.xml

barky02 said:
I have a T-Mobile Moto G XT1032
The Zip file name is: EE-GB-SL_FALCON_KLB20.9-1.10-1.24-1.1_cid7_CFC_1FF.xml
Click to expand...
Click to collapse
Ahhh... I keep forgetting there are so freakin may versions...
can you show a screenshot of what files you have in there
also did you try the
in the command prompt try this
adb kill-server
then type
adb start-server
this will restart the adb session

Here is a another thread to restore stock
http://forum.xda-developers.com/showthread.php?t=2794271
Sent from my Moto G using XDA Free mobile app

hhp_211 said:
Ahhh... I keep forgetting there are so freakin may versions...
can you show a screenshot of what files you have in there
also did you try the
in the command prompt try this
adb kill-server
then type
adb start-server
this will restart the adb session
Click to expand...
Click to collapse
These are the files in the xml folder - mflashboot was the thing I added
Im not too brainy with cmd, at what time do I put adb kill-server in?

sorry
barky02 said:
Thank youu :3
404 error? is it the right link?
Click to expand...
Click to collapse
Sorry bro, my bad xs hope this works.
http://forum.xda-developers.com/moto-g/help/fix-bricked-xt1032-t2814093

barky02 said:
These are the files in the xml folder - mflashboot was the thing I added
Im not too brainy with cmd, at what time do I put adb kill-server in?
Click to expand...
Click to collapse
thanks
after reading some more up on mfastboot I don't believe you have to use the adb commands...
you should be able to use this file mfastboot.bat.txt as long as you have the mfastboot.exe on your pc
download it and move it into your "EE-GB-SL_FALCON_KLB20.9-1.10-1.24-1.1_cid7_CFC_1FF.xml" folder
then rename it to just mfastboot.bat
and doubleclick that
and follow along
don't worry if you see errors on your device screen, it's normal
this is the contents and the correct flashing order of the bat file
and are for that xml.zip that you have
edit:: edited to remove file and update below code to hopefully work
Code:
SET mfastboot=mfastboot.exe
%mfastboot% flash aboot emmc_appsboot.mbn
%mfastboot% flash partition gpt.bin
%mfastboot% flash motoboot motoboot.img
%mfastboot% flash logo logo.bin
%mfastboot% flash boot boot.img
%mfastboot% flash recovery recovery.img
%mfastboot% flash system system.img_sparsechunk.0
%mfastboot% flash system system.img_sparsechunk.1
%mfastboot% flash system system.img_sparsechunk.2
%mfastboot% flash modem NON-HLOS.bin
%mfastboot% erase modemst1
%mfastboot% erase modemst2
%mfastboot% flash fsg fsg.mbn
%mfastboot% erase cache
%mfastboot% erase userdata

hhp_211 said:
thanks
after reading some more up on mfastboot I don't believe you have to use the adb commands...
you should be able to use this file mfastboot.bat.txt as long as you have the mfastboot.exe on your pc
download it and move it into your "EE-GB-SL_FALCON_KLB20.9-1.10-1.24-1.1_cid7_CFC_1FF.xml" folder
then rename it to just mfastboot.bat
and doubleclick that
and follow along
don't worry if you see errors on your device screen, it's normal
this is the contents and the correct flashing order of the bat file
and are for that xml.zip that you have
Code:
SET mfastboot=mfastboot.exe
%mfastboot% flash aboot emmc_appsboot.mbn
%mfastboot% reboot-bootloader
%mfastboot% flash partition gpt.bin
%mfastboot% flash motoboot motoboot.img
%mfastboot% flash logo logo.bin
%mfastboot% flash boot boot.img
%mfastboot% flash recovery recovery.img
%mfastboot% flash system system.img_sparsechunk.0
%mfastboot% flash system system.img_sparsechunk.1
%mfastboot% flash system system.img_sparsechunk.2
%mfastboot% flash modem NON-HLOS.bin
%mfastboot% erase modemst1
%mfastboot% erase modemst2
%mfastboot% flash fsg fsg.mbn
%mfastboot% erase cache
%mfastboot% erase userdata
%mfastboot% reboot-bootloader
Click to expand...
Click to collapse
@hhp_211
I think this will work but I just need the pc to recognise the device, I have attached screenshots of what the device is coming up as. I have installed Motorola Device Manager, SDK tools and Google USB but it still won't be recognise.
I ran the .bat file but command prompt is still saying <waiting for device>
Thank you so much for your help, I think its nearly fixed
Matt

barky02 said:
@hhp_211
I think this will work but I just need the pc to recognise the device, I have attached screenshots of what the device is coming up as. I have installed Motorola Device Manager, SDK tools and Google USB but it still won't be recognise.
I ran the .bat file but command prompt is still saying <waiting for device>
Thank you so much for your help, I think its nearly fixed
Matt
Click to expand...
Click to collapse
@ barky02
have you also installed the
Moto G USB Drivers (WinXP/7 32Bit-64Bit)
http://forum.xda-developers.com/showthread.php?t=2550635
what os are you running on your pc?
.

hhp_211 said:
@ barky02
have you also installed the
Moto G USB Drivers (WinXP/7 32Bit-64Bit)
http://forum.xda-developers.com/showthread.php?t=2550635
what os are you running on your pc?
.
Click to expand...
Click to collapse
@hhp_211
Windows 7 (just with 98 theme)
I already have that installed, and it still doesn't work. A lot of threads are saying to enable usb debugging, but I can't do that in the phones current state right?
I attached the screenshot of what cmd stays on

barky02 said:
Windows 7 (just with 98 theme)
I already have that installed, and it still doesn't work. A lot of threads are saying to enable usb debugging, but I can't do that in the phones current state right?
Click to expand...
Click to collapse
Ok I thought Win 7, but then other shots were looking different...
well I'll ask anyway...
have you downloaded and installed
the Minimal ADB and Fastboot -- Version 1.1.3
https://docs.google.com/file/d/0B1S0LCuXCnnmSWh6NGJmSE1BUWc/edit?usp=sharing
the mfastboot-v2.zip
http://forum.xda-developers.com/attachment.php?attachmentid=2427667&d=1385958280
[[[and extract the zip then copy mfastboot.exe into the same folder as the stock firmware files (the same folder as the .bin and .img files).]]]
then put the .bat file inside the firmware folder,,, then doubleclick the .bat file while phone is in fastboot mode and attached to pc

Moto G XT1032 boot problem

Hi i use this rom http://forum.xda-developers.com/moto-g/development/stable-aosp-caf-t3284323
and i have a problem , my phone rebooted and stuck after the boot animation in a black screen.
I tried wipe cache , nothing and then i tried fix permission and now i cant go into my recovery , restarts itself, flassed revovery again , same thing.
Now i want to flass the rom with fastboot , what wipe commands i have to do?
I found online this
fastboot erase system -w
fastboot erase boot
fastboot update rom.zip
is this ok?
Thanks

[email protected] said:
Hi i use this rom http://forum.xda-developers.com/moto-g/development/stable-aosp-caf-t3284323
and i have a problem , my phone rebooted and stuck after the boot animation in a black screen.
I tried wipe cache , nothing and then i tried fix permission and now i cant go into my recovery , restarts itself, flassed revovery again , same thing.
Now i want to flass the rom with fastboot , what wipe commands i have to do?
I found online this
fastboot erase system -w
fastboot erase boot
fastboot update rom.zip
is this ok?
Thanks
Click to expand...
Click to collapse
I literally JUST unbricked my Moto G XT1032 after searching for a long while and piecing instructions together. Here's how:
PREPARATIONS
1) Download XT1032_RETAIL-BR-SS_4.4.4_KXB21.14-L1.40_42_cid12_CFC_1FF.xml.zip
This is the stock firmware you need to flash. I haven't tried it with anything else. The instructions that follow are specific to this file, although you should be able to follow the general idea to install different ROMS.
Get the firmware (or a different one) here: http://forum.xda-developers.com/moto-g/general/index-moto-g-falcon-factory-firmware-t3110795
2) Ensure that you also have the correct Motorola drivers for this phone. Download 32-bit or 64-bit versions depending on your PC.
Get them here http://forum.xda-developers.com/showthread.php?t=2550635
3) Download MFastBoot v2
Go to http://forum.xda-developers.com/gen...ng-mfastboot-exe-to-unbrick-motorola-t3203518
or simply download the file at (https://mega.nz/#F!xUh10AAD!5NvRwDf6eAfjE3bUWZfk7g)
Note: From what I've experienced, you CANNOT use normal Fastboot on this phone. You will keep getting errors such as Failed (remote failure). You have to use MFastBoot.
Open the downloaded file. There will be two other zip files inside it. Extract all contents of mfastboot-v2.zip to a folder of your choice.
4) Download TWRP Recovery. It's usually a good idea to have a recovery, even though it's not used to flash the ROM.
Get the highest version of it here: https://dl.twrp.me/falcon/
Extract the .img file to the SAME folder as where you extracted mfastboot and rename it to twrp.img (not really necessary, but it's easier to type into the command prompt).
5) Extract all contents of XT1032_RETAIL-BR-SS_4.4.4_KXB21.14-L1.40_42_cid12_CFC_1FF.xml.zip to the SAME folder as where you extracted mfastboot.
6) Ensure the phone is off. Hold VOL DOWN first, and then press POWER button for about 5 seconds, then release POWER button before releasing VOL DOWN. You should be in fastboot mode. Plug the USB cable into the phone now.
If you see Device is locked. Status 0, follow the instructions in the UNLOCKING THE BOOTLOADER section.
If you see Device is unlocked. Status 3, continue to step 7.
FLASHING THE FIRMWARE
7) Open the folder where everything has been extracted to.
Hold CTRL+Shift and right click in an empty area of the folder. You will see a normally hidden option to "Open Command Window Here". Select that option and a command prompt window will open. If you are not seeing this, you may not have administrative rights on your account.
Type this into the command prompt: mfastboot reboot
I'm unsure if this is required or not, but mfastboot wouldn't work unless I rebooted it from the command prompt before any other instruction.
8) This is the step where the TWRP recovery and ROM files are flashed.
Type the following into the command prompt, pressing enter after each line. Alternatively, just copy each line and right click>paste into the command prompt. Credits to AgentChaos for the following:
mfastboot flash partition gpt.bin
mfastboot flash motoboot motoboot.img
mfastboot flash logo logo.bin
mfastboot flash boot boot.img
mfastboot flash system system.img_sparsechunk.0
mfastboot flash system system.img_sparsechunk.1
mfastboot flash system system.img_sparsechunk.2
mfastboot flash modem NON-HLOS.bin
mfastboot erase modemst1
mfastboot erase modemst2
mfastboot flash fsg fsg.mbn
mfastboot erase cache
mfastboot erase userdata
mfastboot flash recovery twrp.img
If you used normal fastboot at this step, it will fail and give you an error of "Failure (remote failure)". or it will say it could not find or write to some directory.
Hopefully it does not fail, and should say OKAY after writing each file. This step will take several minutes.
If you used a different firmware than I did, you will have to flash the correct files to the correct directories, and they MAY be different than the ones listed above. I think (but I am not sure) that the only difference would be having to flash and additional sparsechunk.3 or 4. I would not suggest doing this if you aren't sure.
After all files have been flashed, do one final mfastboot reboot and press VOL DOWN and select Recovery, then press VOL UP to start it. You should see the TWRP recovery screen. The screen may glitch out but otherwise be operable. You can press REBOOT then SYSTEM to start the phone normally.
I hope this has been helpful.
UNLOCKING THE BOOTLOADER
A) Open the folder where everything has been extracted to.
Hold CTRL+Shift and right click in an empty area of the folder. You will see a normally hidden option to "Open Command Window Here". Select that option and a command prompt window will open. If you are not seeing this, you may not have administrative rights on your account.
Connect the USB and type this into the command prompt: mfastboot oem get_unlock_data
You will see a string of characters that looks like:
(bootloader) 0A40040192024205#4C4D3556313230
(bootloader) 30373731363031303332323239#BD00
(bootloader) 8A672BA4746C2CE02328A2AC0C39F95
(bootloader) 1A3E5#1F53280002000000000000000
(bootloader) 0000000
B) Go to Motorola's unlocking bootloder tool website here:
https://motorola-global-portal.custhelp.com/app/standalone/bootloader/unlock-your-device-b
You will need to create an account with a legitimate email account, which takes 1-2 minutes.
There is a text box on Motorola's site where you need to type the exact combined code you received from top to bottom with symbols included, but don't include "(bootloader)". Agree to their terms and services.
C) You will receive an email with your bootloader unlock code.
Go to the command prompt and type: mfastboot reboot to reboot the device. Alternatively, just reboot it manually.
Type: mfastboot oem unlock UNIQUE_KEY where UNIQUE_KEY is the unlock code you received. The screen should go black and you should see the word "Unlock...". The phone may stop responding at this point, in which case simply wait 1-2 minutes to ensure it is finished doing what it was doing, and then manually reboot it.
Boot into fastboot again and now your device should say "Device is unlocked. Status 3"

Just upgraded to LOS 14.1 unofficial from MM - this is how

Thought I would make a thread, which could help someone.
My bootloader is unlocked
I was using Marshmallow LOS 13 unofficial build by Qbanin.
But these directions should be the same for anyone on MM unlocked.
You will need to know how to use ADB from PC and have platform-tools.
The reason I upgraded to 14.1 unofficial instead of official is because official requires the MM modem, and I had already flashed the stock nougat rom when i started looking for roms to flash.
Download the Nougat Stock Firmware:
https://androidfilehost.com/?fid=889964283620765304
Drop the contents of unzipped stock nougat into your platform-tools folder.
Hit the shift button and right click the mouse and 'open command window here'
Connect your MM device to your pc - booted into your current rom with usb debugging enabled
In the command windows type 'adb devices', you may need to confirm access on the screen of your phone, and try the command again.
Make sure your device is listed and authorized.
Type in the command window 'adb reboot bootloader'
Your device will reboot into the bootloader and is ready to program
Run these commands to flash stock nougat, make sure each command succeeds.
If they do not, run any command that fails multiple times until it succeeds and move on to the next, if a command fails more than 5-10 times in a row, start over from the beginning.
fastboot flash partition gpt.bin
fastboot flash bootloader bootloader.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash system system.img_sparsechunk.5
fastboot flash system system.img_sparsechunk.6
fastboot flash system system.img_sparsechunk.7
fastboot flash system system.img_sparsechunk.8
fastboot flash system system.img_sparsechunk.9
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot flash bluetooth BTFM.bin
fastboot erase cache
fastboot erase userdata -w
fastboot reboot
If your device reboots into bootloader repeatedly run this command:
fastboot oem fb_mode_clear
fastboot reboot
Your device will reboot, wait a while during Nougats first run.
Once Nougat is loaded and you pass setup, enable developer options and then ADB usb debugging.
run 'adb devices' command again and confirm the device is listed and authorized.
Download latest official TWRP 3.2.1.0
https://eu.dl.twrp.me/clark/
rename the file to twrp.img and place in the platform-tools folder
Download LOS 14.1 Unofficial (the latest build 2/23 is for MM modem: avoid)
Grab the 2/18 build or read around the forums for latest compatible build
https://androidfilehost.com/?w=files&flid=131793
Move the file to the root of your external sd card via MTP.
Download ARM64 7.1 OpenGapps and move to root of your external sd card
http://opengapps.org/
Run these commands in the command prompt
adb reboot bootloader
adb flash recovery twrp.img
Press 'down vol' for the recovery option and then press the power button
Phone should reboot into TWRP recovery
Allow TWRP to modify contents by swiping at the bottom.
Remember TWRP makes you swipe if your screen shuts off, so you may need to swipe twice to peform operations, ALWAYS PAY ATTENTION IN TWRP.
Select WIPE in twrp, and then ADVANCED WIPE.
Select the Data checkbox and hit the Repair or Change File System at bottom.
Select CHANGE FILE SYSTEM at bottom right.
Select F2FS and proceed with the format.
Select WIPE (again) from home screen choose to wipe dalvik,system,internal & cache
Select INSTALL from home screen and choose the LineageOS 14.1 build.
You will need to SELECT STORAGE at bottom left and choose your external card.
Add the openGapps 7.1 to the install queue as well.
Swipe to confirm flash and let the new rom and gapps install.
After complete wipe dalvik/cache and reboot.
Enjoy your new rom.
I also flashed systemless root in twrp.
https://drive.google.com/file/d/1GjKdxvoTi9YCU43HIy2XTTcB-bGnNn84/view?usp=sharing
This is for unofficial 14.1 only using the 2/10 or 2/18 build only.
The 2/23 build as I understand is a test build for MM modem only.
All future builds should be verified around the forum with hashbangs notes/recommendations as they do not exist at the time of this post.

How To Flash Global Firmware (( PL2-222E-0-00WW-B02 )) Nokia6.1

How to flash the stock global firmware
Hello guys in this thread i`ll provide you esaier way to flash the stock global firmware that`s available with june security patch
PL2-222E-0-00WW-B02
Required things
1- bootloader unlocked
2- enable usb debugging from developer option
3-adb and fastboot tools
4- use this codes to reboot download mode
Code:
adb shell
Code:
reboot bootloader
5- download the zips provided in the link below unzip it on your desktop
6- brain working
INSTALLATION
1- install OST LA 6.0.4 tool (( double click on LAUNCHER.EXE ))
when installition done go to C driver/program files/OST LA folder then look for this tow files and delete them
a- OnlineUpdateTool.exe
b- OnlineUpdateToolConfiger.exe
2- now from OSTLA patch zip copy OnlineUpdateTool.exe to OST folder in C driver then Run it as administrator / click NEXT / click on 3 dots { ... } to pick up PL2-222E-0-00WW-B02.mlf from where you placed the unpacked firmware
3- reboot your phone to downloade mode (( Bootloader )) or (( Fastboot mode )) and plug it into your PC then click next
installation completed now force your phone to reboot recovery ((keep your phone pluged into pc or charger press and hold 3 buttons at the same time when the phone switched off release volume down and keep holding volume up and power then when the bootloader unlocked message disappear release power button now you`ll get page with yellow robot hold power button then once click on volume up okay good now you are in stock recovery go to factory reset then restart system wait the phone till reboot system it`ll take few minutes be patient now system boot you are totally stock update your system and enjoy
you can relock your bootloader as you like {{NOTICE}} after the last August update the unlock.bin file doesn`t work to unlock blootloader you need to set active the inactive slot ""the one with July patch usually on slot b""
command is
Code:
fastboot --set_active=b
5- please forgive me for my bad English
4- don`t forget to hit thanks button if you like my work
DOWNLOAD
unpacked firmware
https://mega.nz/#!jgAXnSrQ!M_NEBQsoNd48qdYpry2L9ER9-Xm5EebBTLgvopCbwJw
OST LA 6.0.4 tool and patch
https://mega.nz/#!2pBXgKgL!TifBFGYWDsC2TqUWzZvTeJlkzJTo0I4MTthCJxuifN0
Sٍpecial Thanks
@hikari_calyx to his special work for Nokia users
@blackpanther0582 for his stock fw
@heineken78 for his patch

I reuploade the unpacked firmware folder already edited the files inside all what you need is following the steps to success

#reserved

where did you get this firmware and how do i know you didn't put a trojan in it

prg318 said:
where did you get this firmware and how do i know you didn't put a trojan in it
Click to expand...
Click to collapse
It's from the guy i maintained and he is a trusted guy he provided almost all Nokia firmware
If you can't trust me or trust him so please don't flash it and stay on the safe side ?

Maherabed1986 said:
It's from the guy i maintained and he is a trusted guy he provided almost all Nokia firmware
If you can't trust me or trust him so please don't flash it and stay on the safe side
Click to expand...
Click to collapse
Yeah - I understand. I'm more confused about why Nokia doesn't provide stock images and how people are finding them. Does nokia provide these images to retailers or something?

Maherabed1986 said:
How to flash the stock global firmware
Hello guys in this thread i`ll provide you esaier way to flash the stock global firmware that`s available with june security patch
PL2-222E-0-00WW-B02
Required things
1- bootloader unlocked
2- enable usb debugging from developer option
3-adb and fastboot tools
4- use this codes
Code:
adb shell
Code:
reboot bootloader
5- download the zips provided in the link below unzip it on yor desktop
6- brain
INSTALLATION
1- install OST LA 6.0.4 tool (( double click on LAUNCHER.EXE ))
when installition done go to C driver/program files/OST LA folder then look for this tow files and delete them
a- OnlineUpdateTool.exe
b- OnlineUpdateToolConfiger.exe
2- now from OSTLA patch zip copy OnlineUpdateTool.exe to OST folder in C driver then Run it as administrator / click NEXT / click on 3 dots ... to pick up PL2-222E-0-00WW-B02.mlf from where you placed the unpacked firmware
if you get any options " in my case i didn`t get any options " check those option (( Normal Download;Erase user data;Erase error data;Erase FRP;Unlock Screen Lock;Check System AP Status ))
3- reboot your phone to downloade mode (( Bootloader )) or (( Fastboot mode )) and plug it into your PC then click next installation completed you`re done
you can now relock your bootloader as you like {{NOTICE}} after the last August update the unlock.bin file doesn`t work to unlock or relock bl you need to set active the other slot ""the one with July patch""
4- don`t forget to hit thanks button if you like my work
DOWNLOAD
unpacked firmware
https://mega.nz/#!jgAXnSrQ!M_NEBQsoNd48qdYpry2L9ER9-Xm5EebBTLgvopCbwJw
OST LA 6.0.4 tool and patch
https://mega.nz/#!2pBXgKgL!TifBFGYWDsC2TqUWzZvTeJlkzJTo0I4MTthCJxuifN0
Sٍpecial Thanks
@hikari_calyx to his special work for Nokia users
@blackpanther0582 for his stock fw
@heineken78 for his patch
Click to expand...
Click to collapse
Is it work on Ta 1054? chinese varient?

juwelrana091 said:
Is it work on Ta 1054? chinese varient?
Click to expand...
Click to collapse
I have no idea if that will work but i heard before you try that with @hikary

juwelrana091 said:
Is it work on Ta 1054? chinese varient?
Click to expand...
Click to collapse
I have no idea if that will work but i heard before you try that with @hikary

I tried, does not work with TA-1054

Does this work with ta1045
Edit - Yes. I didn't try with the OST tool but did it with fastboot and it worked for my 1045

Make sure your device is unlock before you install the August update. Nokia blocked the ability to unlock with the August update.
Aslo, after you install the Global Firmware, do a factory reset from the recovery menu. After it boots into system, reboot to download mode and boot a patched boot file that was created by Maher, that allows you to install Magisk and have root without flashing TWRP. Flashing TWRP, will cause you not to be able to install future OTAs.
The patched boot it's only to boot it temporarily then install magisk direct to your boot:
Link to Maher's XDA post: https://forum.xda-developers.com/nokia-6-2018/development/root-nokia6-1-devices-t3831682
patched_boot_Nokia6.1_Aug.img
https://mega.nz/#!M8klgYqA!fcQU6Dqs9...PwZ0JTScPIPi1A
Here are the commads:
fastboot boot patched_boot_Nokia6.1_Aug.img
then from magisk manager apk install/install direct after the processes done reboot

If you have issue running OST
Edit the PL2-222E-0-00WW-B02.mlf inside the extracted global firmware and modify these values as shown below lines 7-8 and save:
Code:
INITOPTION = 0x20000
INITDLTYPE = 0x60
SECURITY_VER = 0x0001

Danny1976 said:
If you have issue running OST
Edit the PL2-222E-0-00WW-B02.mlf inside the extracted global firmware and modify these values as shown below lines 7-8 and save:
Code:
INITOPTION = 0x20000
INITDLTYPE = 0x60
SECURITY_VER = 0x0001
Click to expand...
Click to collapse
You are super fast buddy i was going to edit the installation steps
Additional to this delete md5 file inside unpacked fw

Maherabed1986 said:
You are super fast buddy i was going to edit the installation steps
Additional to this delete md5 file inside unpacked fw
Click to expand...
Click to collapse
Just trying to help, since you have helped so much.

prg318 said:
Does this work with ta1045
Edit - Yes. I didn't try with the OST tool but did it with fastboot and it worked for my 1045
Click to expand...
Click to collapse
How did you flash it with fastboot?

nikalus said:
How did you flash it with fastboot?
Click to expand...
Click to collapse
Use the "extracted" image (should have a bunch of .elf, .img, and .mbn files). Then you need to execute a bunch of fastboot commands for each partition.
You'll have to adjust the commands somewhat to work with the image that your flashing but you can get an idea of what needs to be done from this script:
PHP:
@echo off
cls
cd /d %~dp0
fastboot oem alive
fastboot flash xbl_a B2N-0-132E-xbl_service.elf
fastboot flash xbl_b B2N-0-132E-xbl_service.elf
fastboot flash abl_a B2N-0-132E-abl_service.elf
fastboot flash abl_b B2N-0-132E-abl_service.elf
fastboot reboot-bootloader
echo.
echo Waiting for device...
@ping localhost -n 5 >nul
echo.
fastboot flash partition B2N-0-132E-gpt_both0.bin
fastboot flash xbl_a B2N-0-132E-xbl_service.elf
fastboot flash xbl_b B2N-0-132E-xbl_service.elf
fastboot flash abl_a B2N-0-132E-abl_service.elf
fastboot flash abl_b B2N-0-132E-abl_service.elf
fastboot flash tz_a B2N-0-132E-tz.mbn
fastboot flash rpm_a B2N-0-132E-rpm.mbn
fastboot flash hwcfg B2N-0-132E-hwcfg.img
fastboot flash hyp_a B2N-0-132E-hyp.mbn
fastboot flash pmic_a B2N-0-132E-pmic.elf
fastboot flash keymaster_a B2N-0-132E-keymaster64.mbn
fastboot flash cmnlib_a B2N-0-132E-cmnlib.mbn
fastboot flash cmnlib64_a B2N-0-132E-cmnlib64.mbn
fastboot flash dsp_a B2N-0-132E-dspso.bin
fastboot flash devcfg_a B2N-0-132E-devcfg.mbn
fastboot flash sec B2N-0-132E-sec.dat
fastboot flash mdtpsecapp_a B2N-0-132E-mdtpsecapp.mbn
fastboot flash storsec B2N-0-132E-storsec.mbn
fastboot flash systeminfo_a systeminfo.img
fastboot reboot-bootloader
echo.
echo Waiting for device...
@ping localhost -n 5 >nul
echo.
fastboot flash modem_a B2N-1-132E-NON-HLOS.bin
fastboot flash mdtp_a B2N-0-132E-00CN-mdtp.img
fastboot flash boot_a B2N-0-132G-00CN-boot.img
fastboot erase boot_b
fastboot flash system_a B2N-0-132E-00CN-system.img
fastboot flash system_b B2N-0-132E-00CN-system_other.img
fastboot flash bluetooth_a B2N-0-132E-BTFM.bin
fastboot flash persist B2N-0-132E-00CN-persist.img
fastboot erase userdata
fastboot flash sutinfo B2N-00CN-001-sutinfo.img
fastboot flash nvdef_a B2N-0-132E-NV-default.mbn
fastboot flash hidden_a C1N-0-0020-0001-hidden.img.ext4
fastboot flash cda_a B2N-00CN-007-cda.img
fastboot erase ssd
fastboot erase misc
fastboot erase sti
fastboot flash splash_a B2N-00CN-007-splash.img
fastboot erase ddr
fastboot flash KEY_INFO B2N-00CN-006-keyinfo.img
:flash_vendor
fastboot flash vendor_a B2N-0-132E-00CN-vendor.img >log.txt 2>&1
find /i "FAILED" log.txt
if %errorlevel% NEQ 0 (
echo OKAY
) else (
echo WRITE FAILED REFLASHING...
call:flash_vendor
)
fastboot flash xbl_a B2N-0-132E-xbl.elf
fastboot flash xbl_b B2N-0-132E-xbl.elf
fastboot flash abl_a B2N-0-132E-abl.elf
fastboot flash abl_b B2N-0-132E-abl.elf
fastboot oem set_active _a
fastboot oem enable-charger-screen
:flash_e2p_package
fastboot flash e2p_package B2N-0-132E-e2p.tar >log.txt 2>&1
find /i "FAILED" log.txt
if %errorlevel% NEQ 0 (
echo OKAY
) else (
echo WRITE FAILED REFLASHING...
call:flash_e2p_package
)
:flash_e2p_script
fastboot flash e2p_script B2N-0-132E-e2p.sh >log.txt 2>&1
find /i "FAILED" log.txt
if %errorlevel% NEQ 0 (
echo OKAY
) else (
echo WRITE FAILED REFLASHING...
call:flash_e2p_script
)
:flash_md4
fastboot flash md4 md4.dat >log.txt 2>&1
find /i "FAILED" log.txt
if %errorlevel% NEQ 0 (
echo OKAY
) else (
echo WRITE FAILED REFLASHING...
call:flash_md4
)
echo.
echo rebooting device...
echo done!
del log.txt
pause
exit

waiting for device
someone know a solution?

nokia a said:
waiting for device
someone know a solution?
Click to expand...
Click to collapse
Install Nokia Driver

could you send me the drivers that work? nokia ta-1054

General P11 plus 616f installation rom gsi + root

Start by downloading the official stock rom. If you had a problem with the installation or just want to go back to the original usage
Flash SP Tools
- download the latest version of Android sdk platform-tools
- Put in the platform-tools folder your boot.img and vbmeta.img that you have copied from your previously downloaded official rom.
- Then download the generic system image you want to install, put it in the platform-tools folder and rename it GSI.img
- Put your smartphone in developer mode, in the settings press 7 times on the build number
- In the menu Options for developers that appeared, you must enable OEM unlocking, enable USB debugging
- Connect the smartphone to the computer, in Configuration usb choose Connection sharing via usb
accept the requested authorization on your smartphone,
- In the platform-tools folder enter the command
adb reboot bootloader
fastboot flashing unlock Press VOL+ to confirm
fastboot flashing unlock_critical Press VOL+ to confirm
fastboot --disable-verification flash boot boot.img
fastboot --disable-verify flash vbmeta vbmeta.img
fastboot -w
fastboot reboot fastboot The tel switch to FastbootD mode and wait for a moment before entering the following command
fastboot delete system
fastboot delete-logical-partition product_a
fastboot --disable-verity --disable-verification system flash Gsi.img Wait for a moment
fastboot -w
fastboot bootloader
fastboot delete user data
fastboot reboot
Lenovo then logo rom gsi and install
evolutionx rom
Releases · ponces/treble_build_evo
Script and patches for building PHH-Treble Evolution X - ponces/treble_build_evo
github.com
rom lenovo and flashtool 616f
https://mirrors.lolinet.com/firmware/lenovo/Tab_P11_Plus/TB-J616F/TB-J616F_S240155_230210_ROW_SVC.zip
https://mirrors.lolinet.com/firmware/lenovo/Tab_P11_Plus/flashtool/MTK_Flash_Tool_v5.2104_P522.zip
Last tested rom that works
https://private.projectelixiros.com/thirteen/gsi/ProjectElixir_3.6_gsi-13.0-20230223-1108-OFFICIAL.img.xz
Root lenovo 616f
Install the Magisk app to your phone and install
In the Options menu, enable both the Preserve Force Encryption and Recovery Mode options.
Choose Select and Patch a file.
Browse to the extracted boot.img file and select it.
Magisk will now load the boot.img file and start patching.
Then the patched patched boot image file will be saved as magisk_patched.img in Internal Storage Downloads.
The file will be named as magisk_patched.img.
Transfer the magisk_patched.img file to the platform-tools folder.In the platform-tools folder enter the command
adb reboot bootloader
fastboot flash boot magisk_patched.img
fastboot reboot
successfully rooted
Magisk 25.2
https://github.com/topjohnwu/Magisk/releases/download/v25.2/Magisk-v25.2.apk

Can you make a video to review that rom on p11

It has only one flaw,
The PC does not recognize the tablet, it can only be charged, files cannot be transferred and adb does not work either.