Hi All, I have bricked my SCH-I925 (Verizon) And need some help.
What I have done so far:
I unlocked the bootloader with the tool from AdamOutler
http://forum.xda-developers.com/showthread.php?p=41016954
It workt just fine, but after a wile I tried to do a factory reset. After that it was not booting anymore and always ended up in TWRP.
I then decided to do a system repair to factory rom with the Verizon tool, This went wrong and now it is not booting anymore. I can enter ODIN mode but it will not accept any roms, Also the Verizon repair tool is not able to load the factory rom and get stuck on 83% falling back to 66% with the message the device is unexpectedly disconnected.
What I have now is the unencrypted factory rom grabed it from the Verizon tool when it was trying to write it to the device. And a Unit that will not accept any writing of roms.
Does anyone know how to resolve this problem?
I also have access to a RIFF-Box and second working SCH-I925 but unfortunately no info about the JTAG pinout of the device.
hope to help
Hi, I've looking for the tool CASUAL(R478b) everywhere , but I can't find it anymore ,the link has expired. Can you share it to me please. Thank you very much!!!!
Or ,you can email it to me :
[email protected]
Thank you again!
Not sure who you are asking as OP was seven years ago .
Posted an email is liable to get a flood of spam .
Hi everybody,
Ive updated my Mate 9 to Android 8 by FF. I used an aproved update by imei. No bootloader open or rooted phone. just normal update.
Now when i boot, phone shows me the Huawei eRecovery and wants to download the lastest version but I dont know why. I try to download by wifi and says there is a problem...any ideas? That means its bricked?
Please help
Happened to me too in a different updating scenario. I unplugged from usb and booted into recovery. Wiped cache then factory reset phone and it was fixed.
Hi team,
My phone was on MHA-L09C432B198 and today I made a wrong update to -> MHA-L09C185B360(8.0.0.360)
My question is that i dont know which firmware install from HuaweiFunk to revert this...i tried MHA-L09 8.0.0.361(C432) but i gave me error...
Any ideas please?
Thanks,
Hi guys, please help me with huawei id on this phone, i try everything i have found, but nothing of solutions didnt work. Sorry my bad english i hope u understand me and thanks to all who give me answer.
lcanl said:
Hi guys, please help me with huawei id on this phone, i try everything i have found, but nothing of solutions didnt work. Sorry my bad english i hope u understand me and thanks to all who give me answer.
Click to expand...
Click to collapse
Whats your problem?
Lukke2804 said:
Whats your problem?
Click to expand...
Click to collapse
My problem is huawei id, i need to erase id.
clear data for hi APp, Huawei apps etc or just do factory reset all will go away
shashank1320 said:
clear data for hi APp, Huawei apps etc or just do factory reset all will go away
Click to expand...
Click to collapse
Factory reset is done but huawei id dont erase.
lcanl said:
Factory reset is done but huawei id dont erase.
Click to expand...
Click to collapse
Talking about app or app data for it..app wont go with factory reset and need to root and disable manually
shashank1320 said:
Talking about app or app data for it..app wont go with factory reset and need to root and disable manually
Click to expand...
Click to collapse
Sorry but client dont know about this, so he done factory reset without cleaning id and appdata, phone is on activation now.
Unable to Get Phone ID
I am unable to get my Honor 8 phone ID which I require to 'unlock' the bootloader as the phone will NOT start up into Android. It boots to the point where it asks for the Region, then Language, then WiFi, etc and then it goes back to the beginning, THUS Region, Language, WiFi, etc. but it never boots into Android as a result I am not able to check the Phone ID or to enable anything like USB debugging, etc.
What I have done to get to this point:
The phone updated > it seems like the update was unsuccessful as it got stuck in a loop where it would ONLY boot to the Huawei eRecovery.
Then I read a post to 'roll-back' to the earliest version (FRD-AL10...135) which I did and then from the SD Card installed the stock firmware (update.app) by using the Pwr+Volme UP+Volume Down buttons. It succeeded to install the stock firmware and ever since then I am stuck at the Region, Language, WiFi, Terms Agreement,etc - BUT it never gets past the selection - it just loops over and over.
I have again installed the stock firmware as above, but it fails to start and continuously gets stuck at the Region, Language, etc selections.
Could anyone please provide help if possible.
All the other posts I read, I need the 'bootloader' to be unlocked, BUT I am unable to get the Phone ID to get the UNLOCK code.
I have also read some posts which suggests I use 'adb' and 'fastboot' to 'recover' the phone to stock firmware, BUT I constantly get an error - "FAILED - Remote: Command not allowed".
So at this point I am not sure how to go any further.
PS: I have also had the phone to my local Huawei Service Centre, but they refuse to help me with the Honor 8 as I did not buy it in S-Africa.
Equalibrium_tdb said:
I am unable to get my Honor 8 phone ID which I require to 'unlock' the bootloader as the phone will NOT start up into Android. It boots to the point where it asks for the Region, then Language, then WiFi, etc and then it goes back to the beginning, THUS Region, Language, WiFi, etc. but it never boots into Android as a result I am not able to check the Phone ID or to enable anything like USB debugging, etc.
What I have done to get to this point:
The phone updated > it seems like the update was unsuccessful as it got stuck in a loop where it would ONLY boot to the Huawei eRecovery.
Then I read a post to 'roll-back' to the earliest version (FRD-AL10...135) which I did and then from the SD Card installed the stock firmware (update.app) by using the Pwr+Volme UP+Volume Down buttons. It succeeded to install the stock firmware and ever since then I am stuck at the Region, Language, WiFi, Terms Agreement,etc - BUT it never gets past the selection - it just loops over and over.
I have again installed the stock firmware as above, but it fails to start and continuously gets stuck at the Region, Language, etc selections.
Could anyone please provide help if possible.
All the other posts I read, I need the 'bootloader' to be unlocked, BUT I am unable to get the Phone ID to get the UNLOCK code.
I have also read some posts which suggests I use 'adb' and 'fastboot' to 'recover' the phone to stock firmware, BUT I constantly get an error - "FAILED - Remote: Command not allowed".
So at this point I am not sure how to go any further.
PS: I have also had the phone to my local Huawei Service Centre, but they refuse to help me with the Honor 8 as I did not buy it in S-Africa.
Click to expand...
Click to collapse
Dload the same firmware which you had before b135
shashank1320 said:
Dload the same firmware which you had before b135
Click to expand...
Click to collapse
It is impossible to determine which firmware the phone had before it broke as I imported the phone from China, and I did not have a reason to unlock the phone before it broke, hence the reason I did not have a need for the Product ID when the phone functioned properly, it is only after it broke that I had to have access to all this information in an attempt to get it back to a functioning state. That being said, the phone worked perfectly for a week until it did an OTA 'update', when the phone restarted I was presented with all kinds of trouble.
I have since been able to start the phone up in Android after I had to buy DC-Unlocker credits to get the phone to boot properly. UN-locking the phone via DC-Unlocker, unlocked the FRP and only thereafter I was able to unlock the bootloader and root the phone, and get access to USB debugging settings, etc.
Hello
I have a soft bricked (?) p40 pro , after downgrading to a wrong firmware version, the phone booted up normally inside android and was working for a while.
But after trying to OTA update it, the phone went into a bootloop. Failed at installation and restarted.
I can access now only eRecovery and Fastboot modes.
I can't get it recornized by a PC with usb, i dont know if i do something wrong.
eRecovery also doesn't work. It managed to find once a package, downloaded it and while installing the deviced rebooted and went into bootloop again.
Now its stuck to unable to find package info.
Haven't try dload from usb-tongle, because i dont have any usb tongle / adapter. Im willing to get one to try out, if i can flash anything from there.
I went to a service shop, they said they tried with test point and they still didn't find a work around it. Maybe they lack experience on this device.
If someone can help me please, im very desperate
I had the phone only for 4 hours
Thanks
Alex
Hi, i have had for many years this phone and if something went really bad and really didn't have the hassle to open the back of the phone to restore it from test point, i would always go to erecovery and let the phone handle the entire process. But now i'm unable to connect to Erecovery services, every time i try it shows me "Getting package info failed"
I have tried the following:
Reflash the board with testpoint
dload method (which always fails with files and with hisuite proxy)
lock the bootloader
change dns as one thread on the honor 6x forum said
i formatted via original recovery
Nothing seems to work
Is anyone having the same problem i have? Does anyone knows the fix to the problem?
I'm having the same issue on my BLN-L24 (I had no issues until I tried to use a custom ROM without deleting fingerprints... oops), any help?