I need help with my op6.
I was using LOS (Unlocked+rooted) until now and I accidentally brick my device, now it's stuck at the bootloader screen.
It doesn't matter if I'm trying to get into the system/recovery.
These are the steps that I did to get here (as far as I can remember):
Wipe system, data, and cache.
Flash latest OxygenOS (9.0.4) using TWRP (blu_spark_v9.96).
Flash TWRP.
Reboot to TWRP
This time it didn't ask me to unlock it with my pattern, and I saw that all of my files in the sdcard folder are encrypted.
I pressed the other partition (A) manually and reboot to TWRP.
It got stuck on the recovery screen.
I flashed TWRP via ADB.
Now the A partitions files are encrypted, I tried to manually move to partition B again, but stuck at crash dump after reboot.
I flashed TWRP via ADB, this time to B.
And now it's stuck at the bootloader...
I can't use the MsmDownloadTool because it's the bootloader and not the crashdump screen, the tool doesn't recognize the device in order to unbrick it.
I even tried to use this guide, but it didn't help, the msmtool still don't recognize it.
I tried to flash TWRP via ADB and this is what I got:
Code:
C:\Users\Folio\Downloads>fastboot flash recovery twrp-3.2.3-x_blu_spark_v9.96_op
6.img
target reported max download size of 536870912 bytes
sending 'recovery' (28892 KB)...
OKAY [ 0.625s]
writing 'recovery'...
FAILED (remote: (recovery_b) No such partition)
finished. total time: 0.625s
I also tried these commands:
Code:
C:\Users\Folio\Downloads>fastboot getvar current-slot
current-slot: b
finished. total time: -0.000s
C:\Users\Folio\Downloads>fastboot flash boot_b twrp-3.2.3-x_blu_spark_v9.96_op6.
img
target reported max download size of 536870912 bytes
sending 'boot_b' (28892 KB)...
OKAY [ 0.617s]
writing 'boot_b'...
OKAY [ 0.140s]
finished. total time: 0.773s
C:\Users\Folio\Downloads>fastboot boot twrp-3.2.3-x_blu_spark_v9.96_op6.img
downloading 'boot.img'...
OKAY [ 0.608s]
booting...
FAILED (remote: Failed to load/authenticate boot image: Load Error)
finished. total time: 0.640s
But it didn't really do anything...
I'm out of ideas, what should I do next?
just go use the unbrick tool ?
I've been in your situation a lot of times in the beginning when I started to know about A/B partitioning.
Just fastboot the stock rom found here and you will boot easily in OOS.. Although your internal will be formatted every time you do this.
By the way, when you go to OOS from any ROM, you will always have to format internal storage to make OOS boot. (The step you didnt do in mentioned steps)
Fastboot ROM - https://forum.xda-developers.com/oneplus-6/how-to/rom-stock-fastboot-roms-oneplus-6-t3796665
Blunts47 said:
just go use the unbrick tool ?
Click to expand...
Click to collapse
As I mentioned.
Yes, I have tried that already.
Joyarup said:
I've been in your situation a lot of times in the beginning when I started to know about A/B partitioning.
Just fastboot the stock rom found here and you will boot easily in OOS.. Although your internal will be formatted every time you do this.
By the way, when you go to OOS from any ROM, you will always have to format internal storage to make OOS boot. (The step you didnt do in mentioned steps)
Fastboot ROM - https://forum.xda-developers.com/oneplus-6/how-to/rom-stock-fastboot-roms-oneplus-6-t3796665
Click to expand...
Click to collapse
I never saw in any other guide that It's necessary to also wipe the internal storage.
The OP6 imaging prosses is even more agonizing than I thought it is. :crying:
I'll try the guide that you sent me and will update, thanks for that.
lyor said:
As I mentioned.
Yes, I have tried that already.
I never saw in any other guide that It's necessary to also wipe the internal storage.
The OP6 imaging prosses is even more agonizing than I thought it is. :crying:
I'll try the guide that you sent me and will update, thanks for that.
Click to expand...
Click to collapse
I agree with you, the A/B partitioning is just a pain in the back.
Try that guide, just let your phone boot into fastboot, plug in pc and run the batch file in the zip of the rom and let it proceed.
Joyarup said:
I agree with you, the A/B partitioning is just a pain in the back.
Try that guide, just let your phone boot into fastboot, plug in pc and run the batch file in the zip of the rom and let it proceed.
Click to expand...
Click to collapse
WOW, how is this guide is not more popular?
Anyhow, you just saved my as5 man, thank you!
lyor said:
WOW, how is this guide is not more popular?
Anyhow, you just saved my as5 man, thank you!
Click to expand...
Click to collapse
Haha, glad to be useful. I know right, fastbooting ROMs are not popular these days. Everyone just follows the unbrick tool..
Enjoy!!
btw, can I now move freely to any other ROM without touching (flashing) the stock ROM?
lyor said:
btw, can I now move freely to any other ROM without touching (flashing) the stock ROM?
Click to expand...
Click to collapse
Yes, if you are booted to OOS once, you can flash any ROMs now. But remember while flashing back the OOS, you will need to wipe internals.
Joyarup said:
Yes, if you are booted to OOS once, you can flash any ROMs now. But remember while flashing back the OOS, you will need to wipe internals.
Click to expand...
Click to collapse
Oh yes, one last thing.
Will I be able to install them without flashing TWRP every time after them (for both of the A/B slots)?
lyor said:
Oh yes, one last thing.
Will I be able to install them without flashing TWRP every time after them (for both of the A/B slots)?
Click to expand...
Click to collapse
Always flash ROM zip + Twrp
Then reboot to TWRP then flash gapps and magisk(if any).
And never change boot partition through twrp, it will brick you. It's kinda buggy...
Related
Hi Guys,
Hoping you can help me with this.
I was originally running Slimkat 4.4.4 and had the latest TWRP installed.
I downloaded the file for LPX13D and extracted all of the files right down to the Flash-all.bat and the images for bootloader, radio, and the system.
I ran the Flash-all.bat, and it installed everything successfully. The device booted, and voila, I am on 5.0 now.
The problem now, is that when I reboot into recovery, I am instead met with the little android guy laying on his back, with a red triange/exclamation point in his chest.
No problem, I say to myself. I'll just flash TWRP manually.
So I go to the bootloader, and try the command fastboot flash recovery recovery.img (renamed to make it faster to type.)
It goes through the motions, and says it was successful.
But when I go to recovery, it's the same red triange guy still.
I tried pressing volume up, power+volume up, etc. No dice. After about 30 seconds, it reboots on it's own back to system.
When I connect it to the Nexus Root Toolkit, and click on Flash recovery, and then choose TWRP latest, I get a window that pops up that tells me :
______
File Dependency Download
Status: Stock Kernel: Not Present - Need to download (this is in red)
Then a button that says "Download + Update All File Dependencies"
So what's my best option here? Should I let the NRT update the dependencies?
Try to flash cwm and tell me what happens
Isus <3 said:
Try to flash cwm and tell me what happens
Click to expand...
Click to collapse
D:\DOWNLOADS>fastboot flash recovery cwm.img
target reported max download size of 1073741824 bytes
sending 'recovery' (11312 KB)...
OKAY [ 0.561s]
writing 'recovery'...
OKAY [ 0.930s]
finished. total time: 1.491s
D:\DOWNLOADS>fastboot reboot-bootloader
rebooting into bootloader...
OKAY [ 0.001s]
finished. total time: 0.001s
I then selected recovery, and lo and behold, it worked! I'm in CWM.
So then i flashed TWRP again, and now it's working properly too.
I don't know why it refused to work the first time, but now it seems to be okay. How strange.
Thanks for your time and help. I appreciate it.
deleted
Stupendousman2012 said:
D:\DOWNLOADS>fastboot flash recovery cwm.img
target reported max download size of 1073741824 bytes
sending 'recovery' (11312 KB)...
OKAY [ 0.561s]
writing 'recovery'...
OKAY [ 0.930s]
finished. total time: 1.491s
D:\DOWNLOADS>fastboot reboot-bootloader
rebooting into bootloader...
OKAY [ 0.001s]
finished. total time: 0.001s
I then selected recovery, and lo and behold, it worked! I'm in CWM.
So then i flashed TWRP again, and now it's working properly too.
I don't know why it refused to work the first time, but now it seems to be okay. How strange.
Thanks for your time and help. I appreciate it.
Click to expand...
Click to collapse
Twrp is not optimized yet well like cwm is for andorid l
Recovery won't work AT ALL no matter what you do until you reflash a KK userdata.img, which also wipes all data in the process.
Lethargy said:
I flashed the new developer preview for 5 minutes or so then went to revert. Recovery wouldn't boot not matter what I flashed, until I flashed a KK userdata.img. So it seems like the new developer preview changes the internal storage/data partition more then the old one.
Click to expand...
Click to collapse
Don't try getting around it. Nothing to do with anything else.
Isus <3 said:
Twrp is not optimized yet well like cwm is for andorid l
Click to expand...
Click to collapse
What? CWM is outdated.
Lethargy said:
Recovery won't work AT ALL no matter what you do until you reflash a KK userdata.img, which also wipes all data in the process.
Don't try getting around it. Nothing to do with anything else.
What? CWM is outdated.
Click to expand...
Click to collapse
Well, Twrp worked until I rebooted and then tried going back to it. Then bam! back to the error dude with the triangle.
So, I flashed cwm again, and that one seems to be persisting after a reboot, so I guess I'm stuck with cwm for now....
I also flashed the boot.img and the supersu update to get root working, and it seems to be going well now.
Cwm tells me that I may have lost root immediately after flashing the supersu update, but when I reboot, root is actually working. What a weird bunch of crap to go through.
Stupendousman2012 said:
Well, Twrp worked until I rebooted and then tried going back to it. Then bam! back to the error dude with the triangle.
Click to expand...
Click to collapse
Flash userdata.img and your TWRP will work properly.
Stupendousman2012 said:
So, I flashed cwm again, and that one seems to be persisting after a reboot, so I guess I'm stuck with cwm for now....
Click to expand...
Click to collapse
It isn't whether its persisting or not. TWRP just won't boot properly until you reflash a KK userdata.img. I don't know why CWM would even boot up, nor why anyone would want to really use it anyways.
Stupendousman2012 said:
Cwm tells me that I may have lost root immediately after flashing the supersu update, but when I reboot, root is actually working. What a weird bunch of crap to go through.
Click to expand...
Click to collapse
It says that because CWM is outdated.
Lethargy said:
Flash userdata.img and your TWRP will work properly.
It isn't whether its persisting or not. TWRP just won't boot properly until you reflash a KK userdata.img. I don't know why CWM would even boot up, nor why anyone would want to really use it anyways.
It says that because CWM is outdated.
Click to expand...
Click to collapse
Okay:
So I extract the userdata from a 4.4.4 stock image, yes? If not, can you point me in the direction of the correct userdata.img
I assume the correct order and syntax is:
fastboot flash userdata userdata.img
fastboot reboot-bootloader
fastbook flash recovery twrp.img
Fastboot reboot-bootloader
Select recovery
Wipe data/Factory reset, and then and reboot system.
Set up phone as normal.
Have I overlooked anything?
Stupendousman2012 said:
Okay:
So I extract the userdata from a 4.4.4 stock image, yes? If not, can you point me in the direction of the correct userdata.img
I assume the correct order and syntax is:
fastboot flash userdata userdata.img
fastboot reboot-bootloader
fastbook flash recovery twrp.img
Fastboot reboot-bootloader
Select recovery
Wipe data/Factory reset, and then and reboot system.
Set up phone as normal.
Have I overlooked anything?
Click to expand...
Click to collapse
Yeah. Don't need to boot into recovery and wipe data since flashing a .img with fastboot while in bootloader erases it first then flashes. Just make sure you backup your stuff, including internal storage, off to a PC first if you have anything important.
Until L is officially released, we're using the below thread
http://forum.xda-developers.com/show....php?t=2796217
Android "L" Developer Preview Help, Troubleshooting, Q&A
Sent from my Nexus 5 using Tapatalk
Hello All,
I tried many ROMs but somehow now I am not able to boot in TWRP after flashing it.
Not able to add image here.
Command used is fastboot flash recovery twrp-2.8.6.0-bacon.img
target reported max download size of 536870912 bytes
sending recovery (10180 KB)
OKAY [ 0.368s]
writing recovery
OKAY [ 0.186s]
finished total time 0.554s
I can boot in fastboot mode. Any help would be appreciates. Thanks
Sanjay13 said:
Hello All,
I tried many ROMs but somehow now I am not able to boot in TWRP after flashing it.
Not able to add image here.
Command used is fastboot flash recovery twrp-2.8.6.0-bacon.img
target reported max download size of 536870912 bytes
sending recovery (10180 KB)
OKAY [ 0.368s]
writing recovery
OKAY [ 0.186s]
finished total time 0.554s
I can boot in fastboot mode. Any help would be appreciates. Thanks
Click to expand...
Click to collapse
Boot into twrp just after you flash it.And flash latest twrp this time.
I recommend @kutep0v 's twrp.
Mr.Ak said:
Boot into twrp just after you flash it.And flash latest twrp this time.
I recommend @kutep0v 's twrp.
Click to expand...
Click to collapse
hello,
I am getting a error
booting
Failed ( remote:dtb not found)
Sanjay13 said:
hello,
I am getting a error
booting
Failed ( remote:dtb not found)
Click to expand...
Click to collapse
You mean a error while flashing recovery?
Just after flashing, long press volume down plus power button to restart & get into recovery.
In case problem persists, memory could be corrupted.
You might need to start afresh installing cm13 snapshot. That'll wipe your phone internal memory as well.
kapil_dheer said:
Just after flashing, long press volume down plus power button to restart & get into recovery.
In case problem persists, memory could be corrupted.
You might need to start afresh installing cm13 snapshot. That'll wipe your phone internal memory as well.
Click to expand...
Click to collapse
Thanks Kapil. I could resolve the problem myself. I did a instaal cm13 using the below link.
http://tweakguy.com/return-your-oneplus-one-to-full-stock/
Then flashed TWRP and then had the ROM installed. Guess now I can flash anything for OPO.
Well my due credit to TweakGuy and also to DeadlyIndian for the ROM below having the latest Oxygen and Marshmellow
https://forum.xda-developers.com/oneplus-one/development/rom-oxygenos-3-1-2-t3470907
Thanks once again to all who read this.
ttps://forum.xda-developers.com/oneplus-6/themes/magisk-aod-lockscreen-weather-mods-oos-t3847008
OPENBETA3 I installed this module magiskden to my oneplus 6 device installed in rom. I installed the system backup from twrp (bluspark v9.85) before installing.
When I set up the module and restart it, the screen was opened and closed, it was not possible to enter magisk manager.
Twrpye and I said 'restore system'. When the Restore process was completed, I said reboot system and went into fastboot mode.
I can't boot to the phone and write twrp. Fastboot is entering mode every time I restart.
I need to save my data. I don't want to flash fastboot rum.
I think there is no way without msmtool. I had the same problem when I tried to restore backup.
Kollachi said:
I think there is no way without msmtool. I had the same problem when I tried to restore backup.
Click to expand...
Click to collapse
fastboot boot twrp-3.2.1-0-enchilada.img
downloading 'boot.img'...
OKAY [ 0.579s]
booting...
FAILED (remote: Failed to load/authenticate boot image: Load Error)
finished. total time: 0.609s
have you received such an error?
This isn't related to the module and seems to happen whenever I try to restore /boot or /system using TWRP. This is easily fixable by flashing the original boot.img
Is there any other solution than flashing the factory rum? At least if I twrp, I would back up internal storage.
DevrimSeven60 said:
fastboot boot twrp-3.2.1-0-enchilada.img
downloading 'boot.img'...
OKAY [ 0.579s]
booting...
FAILED (remote: Failed to load/authenticate boot image: Load Error)
finished. total time: 0.609s
have you received such an error?
Click to expand...
Click to collapse
Yes I had the same error
Kollachi said:
Yes I had the same error
Click to expand...
Click to collapse
what is the solution? Bluspark twrp flash I do not get error, but twrpye can not enter, although it is completed.
DevrimSeven60 said:
Is there any other solution than flashing the factory rum? At least if I twrp, I would back up internal storage.
Click to expand...
Click to collapse
You can try flash the boot.img like paphonb said. I didn't knew that and used msmtool. But I saved my data before restoring in twrp so I didn't lose anything just a lil bit time
paphonb said:
This isn't related to the module and seems to happen whenever I try to restore /boot or /system using TWRP. This is easily fixable by flashing the original boot.img
Click to expand...
Click to collapse
open beta 3 i have downloaded full rom zip. Is there an img I can use in zip?
My OnePlus 7 Pro keep booting into fastboot mode. Neither I can access recovery nor can start the phone. It's always comes back to recovery.
Please help me getting it done.
Bootloader is unlocked.
You haven't given enough info, tell us step by step how your "Bootloader is unlocked".
We would need to know if you did it properly, you probably need to go into the recovery and perform a "Full wipe". Unlocking the bootloader usually does that anyway.
The normal method is:
Enabled developer settings by pressing the version number in the about section 7 times and entering your pin
Copy the adb developer folder from the mounted OnePlus driver partition you usually get on your computer when attaching the phone, into a folder on your hard drive, and enable adb in developer settings.
In developer settings enable "OEM unlocking"
Reboot into fastboot mode
Open a command window (with admin privileges) in the folder you copied to your hard drive (In Windows, hold down shift and right click inside the folder, then click "Open Command Window..."
Run the command "fastboot oem unlock"
Accept the prompt shown on the phone
This will wipe the phone back to factory reset so ensure you have backed up your data, although you should be doing that before you even start.
Flash the appropriate TWRP recovery partition (which afaik isn't even available yet so I'm not sure why you would unlock the bootloader so soon to be honest
If you didn't perform those steps or performed them in the wrong order then you've done it wrong.
Performing a factory reset in the recovery partition may get it booting again but it's hard to know with the minimal information you've provided.
Although again, why are you unlocking the bootloader when there hasn't been a TWRP version released yet? You won't be able to flash anything, not even Magisk.
I've unlocked bootloader by command of OEM unlocking.
After than the unlock, I rebooted it's again And installed some Magisk file, which made it stuck at fastboot.
I can't access the Recovery nor can restart Phone.
All I can do is switched it off And get back into fastboot again after.
Yeah, you can't flash things with the default recovery (That's just made for flashing the default builds), that's most likely why. Magisk was made to be flashed with TWRP.
Did you use the test TWRP here? If so, then go to that thread for help.
If you can get into the OnePlus recovery you could maybe grab a build from here and flash the default rom back, then start again using the guide I showed you but, tbh, I would wait until a good TWRP build is established and Magisk is confirmed to be working.
That thread also looks like it has the default recovery image too so you can flash that back on the phone with :
fastboot flash recovery filename (Just put the recovery image into the same folder as your adb.exe and fastboot.exe
Then see if you can reboot into it and flash the stock rom back on from the same thread.
How can I get things done back, all I've is fastboot.
It's a New set, please help (
dmishra639 said:
How can I get things done back, all I've is fastboot.
It's a New set, please help (
Click to expand...
Click to collapse
If you have fastboot, I've just told you how to get the default recovery back in above.
---------- Post added at 05:45 PM ---------- Previous post was at 05:28 PM ----------
Reading that thread again, flashing recovery is not as simple as it used to be due to the A/B partition model used now, so you'll need to read the instructions shown for recovery. My guess is that you didn't read them properly and flashed the recovery to the wrong partition. If you have flashed that TWRP then you need to seek support in that thread.
It's not gonna work with me,
Even if I'll download the zip file it's only flashable with a Twrp or Stock recovery. As stock recovery is not working.
Even if I'll try to flash a Twrp recovery it's showing up an error to me :
PS C:\adb> fastboot devices
420bdc60 fastboot
PS C:\adb> fastboot boot C:\adb\recovery.img
downloading 'boot.img'...
OKAY [ 0.585s]
booting...
FAILED (remote: unknown command)
finished. total time: 0.636s
PS C:\adb> fastboot flash recovery C:\adb\recovery.img
target reported max download size of 805306368 bytes
sending 'recovery' (18828 KB)...
OKAY [ 0.575s]
writing 'recovery'...
FAILED (remote: (recovery_b) No such partition)
finished. total time: 0.580s
PS C:\adb>
dmishra639 said:
It's not gonna work with me,
Even if I'll download the zip file it's only flashable with a Twrp or Stock recovery. As stock recovery is not working.
Even if I'll try to flash a Twrp recovery it's showing up an error to me :
PS C:\adb> fastboot devices
420bdc60 fastboot
PS C:\adb> fastboot boot C:\adb\recovery.img
downloading 'boot.img'...
OKAY [ 0.585s]
booting...
FAILED (remote: unknown command)
finished. total time: 0.636s
PS C:\adb> fastboot flash recovery C:\adb\recovery.img
target reported max download size of 805306368 bytes
sending 'recovery' (18828 KB)...
OKAY [ 0.575s]
writing 'recovery'...
FAILED (remote: (recovery_b) No such partition)
finished. total time: 0.580s
PS C:\adb>
Click to expand...
Click to collapse
This will sound stupid, but I had similar issues with the pixel and it was due to drivers and the port. Tried from a different machine and worked. Do you have the luxury to do so ?
Man, I've flashed like tons of Custom ROMs and Twrp from the same machine everytime.
I used to be a Xioami Redmi Note 5 pro user, And I've flashed almost every ROMs And root and everything, and same with my Redmi Note 3.
I don't think the machine have some fault some how.
It was Just like I had unlocked the bootloader And just after I flashed some Magisk ISO file which got flashed completely, And then all I'm stucked with the Fastboot, everything Stopped working, And everytime I'm dragged info fastboot.
And also as I said, can't flash Twrp.
dmishra639 said:
Man, I've flashed like tons of Custom ROMs and Twrp from the same machine everytime.
I used to be a Xioami Redmi Note 5 pro user, And I've flashed almost every ROMs And root and everything, and same with my Redmi Note 3.
I don't think the machine have some fault some how.
It was Just like I had unlocked the bootloader And just after I flashed some Magisk ISO file which got flashed completely, And then all I'm stucked with the Fastboot, everything Stopped working, And everytime I'm dragged info fastboot.
And also as I said, can't flash Twrp.
Click to expand...
Click to collapse
Grab this fastboot rom and flash...
https://forum.xda-developers.com/oneplus-7-pro/how-to/rom-stock-fastboot-roms-oneplus-7-pro-t3931424
Why are you trying to flash recovery partitions when they don't exist on this device? Recovery is on the boot partition.
dmishra639 said:
Man, I've flashed like tons of Custom ROMs and Twrp from the same machine everytime.
I used to be a Xioami Redmi Note 5 pro user, And I've flashed almost every ROMs And root and everything, and same with my Redmi Note 3.
I don't think the machine have some fault some how.
It was Just like I had unlocked the bootloader And just after I flashed some Magisk ISO file which got flashed completely, And then all I'm stucked with the Fastboot, everything Stopped working, And everytime I'm dragged info fastboot.
And also as I said, can't flash Twrp.
Click to expand...
Click to collapse
Since you are familiar with custom rom,unlocked bootloader etc you should had known already that you must NOT flash any kind Magisk staff without having proper and functional twrp.
Even if it flashed successful that doesn't mean will work after reboot and normal restart.
That why you've brick your device.
And on the other hand with A/B partition things has changed dramatically evolving all custom made staff and how they works.
Oneplus device not work the same way as Xiaomi you've described.
Sent from my iPad using Tapatalk Pro
LLStarks said:
Why are you trying to flash recovery partitions when they don't exist on this device? Recovery is on the boot partition.
Click to expand...
Click to collapse
paatha13 said:
Since you are familiar with custom rom,unlocked bootloader etc you should had known already that you must NOT flash any kind Magisk staff without having proper and functional twrp.
Even if it flashed successful that doesn't mean will work after reboot and normal restart.
That why you've brick your device.
And on the other hand with A/B partition things has changed dramatically evolving all custom made staff and how they works.
Oneplus device not work the same way as Xiaomi you've described.
Sent from my iPad using Tapatalk Pro
Click to expand...
Click to collapse
Any post that describe exactly what changed? I havent flashed custom roms/kernels in close to two years due to OOS being satisfying enough. What I have done is fastboot into twrp and flash magisk(I believe). Will I still be able to do that with OP7 Pro?
dmishra639 said:
My OnePlus 7 Pro keep booting into fastboot mode. Neither I can access recovery nor can start the phone. It's always comes back to recovery.
Please help me getting it done.
Bootloader is unlocked.
Click to expand...
Click to collapse
I forget the command, but change the boot slot and try to reboot.
tech_head said:
I forget the command, but change the boot slot and try to reboot.
Click to expand...
Click to collapse
Fastboot flash boot C://path/to/recovery.img
SysAdmNj said:
Any post that describe exactly what changed? I havent flashed custom roms/kernels in close to two years due to OOS being satisfying enough. What I have done is fastboot into twrp and flash magisk(I believe). Will I still be able to do that with OP7 Pro?
Click to expand...
Click to collapse
You can read over here on 6T device details of how thing work with A/B partition.
https://forum.xda-developers.com/on...overy-unofficial-twrp-touch-recovery-t3861482
https://twrp.me/oneplus/oneplus6t.html
https://www.xda-developers.com/how-...ess-updates-affect-custom-development-on-xda/
Also follow this thread about 7 Pro situation and how well work over time
[RECOVERY][3.3.1-2][guacamole]Unofficial TWRP recovery for OnePlus 7 Pro(Testing)
Sent from my iPad using Tapatalk Pro
joemossjr said:
Fastboot flash boot C://path/to/recovery.img
Click to expand...
Click to collapse
Man, thank you so much
You literally made my day,
Wht I've did wrong in a flow was I had given the command: fastboot flash boot and the magisk location.
That was a stupidity, all I forgot was the command.
Now I used the same command and then used oxygen os fastboot flashable all bat file, as suggested by a member.
And here's my phone back. )
Thanks
In case, I'm completely New to OnePlus
It someone suggest me how to Root OnePlus 7 Pro normally, cuz I've to edit the build prop due to some reason.
My bootloader is unlocked but can't flash custom recovery.
dmishra639 said:
In case, I'm completely New to OnePlus
It someone suggest me how to Root OnePlus 7 Pro normally, cuz I've to edit the build prop due to some reason.
My bootloader is unlocked but can't flash custom recovery.
Click to expand...
Click to collapse
I remember when I edit the buildi prob on my v20 to be recognized as a pixel so google assistant can work and that bricked my device.
Robert235 said:
I remember when I edit the buildi prob on my v20 to be recognized as a pixel so google assistant can work and that bricked my device.
Click to expand...
Click to collapse
Man I've a 2gb daily add on (for 3 months), which will only gonna work with my previous device (Redmi note 5 pro).
So, I've to change OnePlus as Note 5 Pro as same.
I've did that tons of time on my past phone,it never did a brick TBH.
I keep trying to flash t.w.r.p via adb but it keeps failing. I try orange and Peter but they don't work and make me get stuck in bootloop. Official 3.3.1 recovery flashes but then when I boot to recovery it only shows the teamwin logo and I have no options to do anything, then on reboot when I trying booting into recovery again it boots into stock recovery like I never even flashed it.
Can someone tell me what I'm doing wrong or tell me correct recovery to flash with this rom? It should be straight forward process to flash t.w.r.p, but I am having trouble for some reason. Thank you.
toyspeed said:
I keep trying to flash t.w.r.p via adb but it keeps failing. I try orange and Peter but they don't work and make me get stuck in bootloop. Official 3.3.1 recovery flashes but then when I boot to recovery it only shows the teamwin logo and I have no options to do anything, then on reboot when I trying booting into recovery again it boots into stock recovery like I never even flashed it.
Can someone tell me what I'm doing wrong or tell me correct recovery to flash with this rom? It should be straight forward process to flash t.w.r.p, but I am having trouble for some reason. Thank you.
Click to expand...
Click to collapse
What's the message that appears in ADB when you flash it?
toyspeed said:
I keep trying to flash t.w.r.p via adb but it keeps failing. I try orange and Peter but they don't work and make me get stuck in bootloop. Official 3.3.1 recovery flashes but then when I boot to recovery it only shows the teamwin logo and I have no options to do anything, then on reboot when I trying booting into recovery again it boots into stock recovery like I never even flashed it.
Can someone tell me what I'm doing wrong or tell me correct recovery to flash with this rom? It should be straight forward process to flash t.w.r.p, but I am having trouble for some reason. Thank you.
Click to expand...
Click to collapse
Did u unlocked the bootloader?
Sent from my Redmi Note 7 Pro using XDA Labs
Naveenthemi said:
What's the message that appears in ADB when you flash it?
Click to expand...
Click to collapse
Just usual message such as:
PS C:\platform-tools> fastboot flash recovery recovery.img
target reported max download size of 536870912 bytes
sending 'recovery' (65536 KB)...
OKAY [ 2.112s]
writing 'recovery'...
OKAY [ 0.355s]
finished. total time: 2.474s
I tried with Black Project also, same story. I don't understand this, I just want to root but I can't!
toyspeed said:
Just usual message such as:
PS C:\platform-tools> fastboot flash recovery recovery.img
target reported max download size of 536870912 bytes
sending 'recovery' (65536 KB)...
OKAY [ 2.112s]
writing 'recovery'...
OKAY [ 0.355s]
finished. total time: 2.474s
I tried with Black Project also, same story. I don't understand this, I just want to root but I can't!
Click to expand...
Click to collapse
Ok someone else who's facing the same problem fixed this by formatting the data partition.
But idk why don't you try reinstalling MIUI(Flashboot it through MiFlash) and then try again?
Naveenthemi said:
Ok someone else who's facing the same problem fixed this by formatting the data partition.
But idk why don't you try reinstalling MIUI(Flashboot it through MiFlash) and then try again?
Click to expand...
Click to collapse
Ok, thanks for advice I'll try formatting data partition. That's exactly what I've been doing, flashing MIUI through MiFlash everything perfect. Then I run into problems after I try flashing recovery so I can root, very weird but I will keep trying.
toyspeed said:
Ok, thanks for advice I'll try formatting data partition. That's exactly what I've been doing, flashing MIUI through MiFlash everything perfect. Then I run into problems after I try flashing recovery so I can root, very weird but I will keep trying.
Click to expand...
Click to collapse
Did it work?
Naveenthemi said:
Did it work?
Click to expand...
Click to collapse
I actually decided to flash Superior OS instead, loving it so far!