Original Thread(s) :
https://goo.gl/Daq3Ut
https://goo.gl/gLSQfm
Why do we have another guide?
I've created this guide to clarify any confusion from other guides.
This guide is a full guide on how to restore your IMEI, no RIY (Research it yourself (Yes, I just made that up XD)).
Notes #1 I'M NOT RESPONSIBLE FOR BRICKING OR DAMAGING YOUR PHONE IN ANY WAY. FOLLOW THIS GUIDE AT YOUR OWN RISK.
Requirements :
A rooted phone
Running stock Nougat ROM
A data transfer cable (stock one works)
Your original IMEI(s) from your box
Some common sense
Required Files :
Nougat ROM* : https://goo.gl/zECMXV
Mi A1 QCN file* : https://goo.gl/LqSJyc
IMEI Converter* : https://goo.gl/NeJf9E
HEX editor : goo.gl/HEXeditor
Platform Tools : https://goo.gl/Cwjo2R
QPST Flash Tool : https://goo.gl/B69twP (Password : qpstflash.com)
Mi Flash Tool : goo.gl/MiFlashTool
Instructions :
Setting up your phone
1. Flash Nougat ROM via Mi Flash. If you're on Pie, then you have to follow a guide to downgrade to Oreo then Nougat, and most importantly, select clean all to keep your bootloader unlocked.
2. Enable USB debugging in developer options.
3. Make sure your phone is rooted properly. Then plug your phone into your PC.
4. Extract Platform tools, in the address bar of the folder type "cmd" then enter. In command prompt, type "adb devices" then enter. Grant access from your phone.
5. After given permission, type "adb shell" and enter. Then type "su" and enter. Grant root access from your phone.
6. Then type "setprop sys.usb.config diag,adb" then enter. You can exit command prompt.
Modifying IMEI(s)
1. Extract IMEI converter and open it.
2. Enter your IMEI's and convert it to hex values. Write the hex values on your Notepad or piece of paper.
3. Extract the QCN file and HEX editor. Open the QCN file with HEX editor.
4. Press "Ctrl+F" and open 'Hex-value' tab and set 'Search Direction' to 'All'. In the tab, search for "08 0A 81 00 25 79 81 67 19" and enter.
5. The hex values should be highlighted. Replace them with your SIM 1's hex values.
6. Once done, repeat step 4, but search for "08 5A 11 40 98 30 21 21 86" and enter.
7. Repeat step 5, but replace it with your SIM 2's hex values.
8. Once replaced correctly. Press 'Save'. *Not Save As*.
9. Rename your saved QCN file to "00000000_0".
Replacing your QCN file
1. On your phone, open the Phone app and dial "*#*#717717#*#*", there should be pop up saying 'diag port enabled'.
2. Install QPST to your PC and open QPST Configuration.
3. Go to Ports/Add New Port, uncheck "Show Serial and USB/QC Diagnostics only", click OK. Unplug and plug your phone to verify which is your COM port.
4. Then go to 'Start Clients' tab and select 'Software Download'. Navigate to 'Restore' tab.
5. Select your phone's port and select your QCN file below it.
6. Check 'Allow phone mismatch', then hit 'Start'.
7. Once done, unplug your phone and restart it.
Verifying your IMEI(s)
1. Open the Phone app and dial "*#06#".
2. Verify that your IMEIs match your box.
Notes #2
If it doesn't show up or doesn't match your box. You must repeat the whole process and wipe your EFS in TWRP by using these commands in the Terminal :
dd if=/dev/zero of=/dev/block/mmcblk0p14
dd if=/dev/zero of=/dev/block/mmcblk0p15
*Files provided by @raaz1431994
Thanks to OP of original threads for providing information.
Created : 4/3/19
Last Updated : 11/5/20
I had to use the dd commands and HxD (instead of the recommended HEX editor) but thank to you by Mi A1 is back on the land of the living.
I have strange issue.
Once i had lost my IMEI while downgrading from pie to oreo. I was not able to restore my IMEI so i went to Mi Service Center and they fixed it.
But after that it has a strange issue. My sim slots are interchanged.
SIM 1 in tray is shown as SIM2 in phone and SIM2 is as SIM1.
Though i have no problem with this as Now PIE support Dual Volte Support.
So just wanted to ask if i interchange my IMEI can this be fixed? My be service center guy misplaced IMEI.
just what I need, thank you OP! Will try to follow the guide and restore IMEI
edit: damn it, I have to find a how-to downgrate to Oreo and then Nougat
twister26 said:
just what I need, thank you OP! Will try to follow the guide and restore IMEI
edit: damn it, I have to find a how-to downgrate to Oreo and then Nougat
Click to expand...
Click to collapse
From Oreo to nougat is straight forward. From pie to nougat requires a guide.
WhatzIt2Ya said:
From Oreo to nougat is straight forward. From pie to nougat requires a guide.
Click to expand...
Click to collapse
Thanks! Do you think downgrading to 8.1 with this tutorial https://forum.xda-developers.com/mi-a1/how-to/tutorial-downgrade-9-0-to-8-1-edl-imei-t3879624 will be enough to get my IMEI back?
twister26 said:
Thanks! Do you think downgrading to 8.1 with this tutorial https://forum.xda-developers.com/mi-a1/how-to/tutorial-downgrade-9-0-to-8-1-edl-imei-t3879624 will be enough to get my IMEI back?
Click to expand...
Click to collapse
No, you have to be on nougat. Plus, that guide made me lose my IMEI. ?
WhatzIt2Ya said:
No, you have to be on nougat. Plus, that guide made me lose my IMEI. ?
Click to expand...
Click to collapse
Dammit!
Can you please link me to a guide you followed to get your IMEI back? I'm on Pie, phone is working even without IMEI. I'd still like to get it back because I'm planning on selling the phone one day and I want IMEI to be present.
twister26 said:
Dammit!
Can you please link me to a guide you followed to get your IMEI back? I'm on Pie, phone is working even without IMEI. I'd still like to get it back because I'm planning on selling the phone one day and I want IMEI to be present.
Click to expand...
Click to collapse
If you already lost it, then you can just follow the downgrade guide.
WhatzIt2Ya said:
If you already lost it, then you can just follow the downgrade guide.
Click to expand...
Click to collapse
Yeah, I'm just a bit afraid to mess up and trying to find a reliable how-to downgrade to 8 and then to 7, restore IMEI and upgrade back to 9. Can you please tell me which guide did you follow to achieve this?
twister26 said:
Yeah, I'm just a bit afraid to mess up and trying to find a reliable how-to downgrade to 8 and then to 7, restore IMEI and upgrade back to 9. Can you please tell me which guide did you follow to achieve this?
Click to expand...
Click to collapse
If you're already on Oreo, just flash the nougat rom with mi flash.
WhatzIt2Ya said:
If you're already on Oreo, just flash the nougat rom with mi flash.
Click to expand...
Click to collapse
I'm on 9 at the moment. Do you think I should be safe if I follow https://forum.xda-developers.com/mi-a1/how-to/tutorial-downgrade-9-0-to-8-1-edl-imei-t3879624 and then follow instructions from the first post?
Thanks for helping me out!
twister26 said:
I'm on 9 at the moment. Do you think I should be safe if I follow https://forum.xda-developers.com/mi-a1/how-to/tutorial-downgrade-9-0-to-8-1-edl-imei-t3879624 and then follow instructions from the first post?
Thanks for helping me out!
Click to expand...
Click to collapse
If you already lost it. Then nothing could get any worse. Just go for it.
Guide updated!
Sorry if anyone couldn't fix their IMEIs. I just refollowed my guide and apparently there are a few flaws in it. All of it has been fixed.
I need to do same process for my Mi 9T, anybody can help me?
Jt380p said:
Original Thread(s) :
https://goo.gl/Daq3Ut
https://goo.gl/gLSQfm
Why do we have another guide?
I've created this guide to clarify any confusion from other guides.
This guide is a full guide on how to restore your IMEI, no RIY (Research it yourself (Yes, I just made that up XD)).
Notes #1 I'M NOT RESPONSIBLE FOR BRICKING OR DAMAGING YOUR PHONE IN ANY WAY. FOLLOW THIS GUIDE AT YOUR OWN RISK.
Requirements :
A rooted phone
Running stock Nougat ROM
A data transfer cable (stock one works)
Your original IMEI(s) from your box
Some common sense
Required Files :
Nougat ROM* : https://goo.gl/zECMXV
Mi A1 QCN file* : https://goo.gl/LqSJyc
IMEI Converter* : https://goo.gl/NeJf9E
HEX editor : goo.gl was discontinued, so no custom URL
Platform Tools : https://goo.gl/Cwjo2R
QPST Flash Tool : https://goo.gl/B69twP (Password : qpstflash.com)
Mi Flash Tool : https://goo.gl/NufKfk
Instructions :
Setting up your phone
1. Flash Nougat ROM via Mi Flash. If you're on Pie, then you have to follow a guide to downgrade to Oreo then Nougat, and most importantly, select clean all to keep your bootloader unlocked.
2. Enable USB debugging in developer options.
3. Make sure your phone is rooted properly. Then plug your phone into your PC.
4. Extract Platform tools, in the address bar of the folder type "cmd" then enter. In command prompt, type "adb devices" then enter. Grant access from your phone.
5. After given permission, type "adb shell" and enter. Then type "su" and enter. Grant root access from your phone.
6. Then type "setprop sys.usb.config diag,adb" then enter. You can exit command prompt.
Modifying IMEI(s)
1. Extract IMEI converter and open it.
2. Enter your IMEI's and convert it to hex values. Write the hex values on your Notepad or piece of paper.
3. Extract the QCN file and HEX editor. Open the QCN file with HEX editor.
4. Press "Ctrl+F" and open 'Hex-value' tab and set 'Search Direction' to 'All'. In the tab, search for "08 0A 81 00 25 79 81 67 19" and enter.
5. The hex values should be highlighted. Replace them with your SIM 1's hex values.
6. Once done, repeat step 4, but search for "08 5A 11 40 98 30 21 21 86" and enter.
7. Repeat step 5, but replace it with your SIM 2's hex values.
8. Once replaced correctly. Press 'Save'. *Not Save As*.
9. Rename your saved QCN file to "00000000_0".
Replacing your QCN file
1. On your phone, open the Phone app and dial "*#*#717717#*#*", there should be pop up saying 'diag port enabled'.
2. Install QPST to your PC and open QPST Configuration.
3. Go to Ports/Add New Port, uncheck "Show Serial and USB/QC Diagnostics only", click OK. Unplug and plug your phone to verify which is your COM port.
4. Then go to 'Start Clients' tab and select 'Software Download'. Navigate to 'Restore' tab.
5. Select your phone's port and select your QCN file below it.
6. Check 'Allow phone mismatch', then hit 'Start'.
7. Once done, unplug your phone and restart it.
Verifying your IMEI(s)
1. Open the Phone app and dial "*#06#".
2. Verify that your IMEIs match your box.
Notes #2
If it doesn't show up or doesn't match your box. You must repeat the whole process and wipe your EFS in TWRP by using these commands in the Terminal :
dd if=/dev/zero of=/dev/block/mmcblk0p14
dd if=/dev/zero of=/dev/block/mmcblk0p15
*Files provided by @raaz1431994
Thanks to OP of original threads for providing information.
Created : 4/03/19
Last Updated : 13/07/19
Click to expand...
Click to collapse
what to do if "*#*#717717#*#*" doesn't work?
This guide worked perfectly for me, thank you very much!
Help me please
when I connect the phone the qpst program does not recognize the usb, but the pc does and I put the code *#*#717717#*#*
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Enviado desde mi Mi A1 mediante Tapatalk
Help
Hi sir i lost my imei and lost my signal like yours. But I restored the imei using qcn file but still the Network is not working please help this problem happens when I tried to flash stock rom using twrp. Please help
after this, if we go to android 8 or 9 does it reset?
Related
Method 1 was discovered by a noob - Dav22. Dazweeja came up with a simple ADB command. Skygear for working it in Terminal Emulator
Method 2 was discovered by sieempi (Links at the bottom), STRING: NOT FOUND workaround found by jackmonter5
Big thanks to xplod4202. Risked his Sensation to see if Methd 2 was safe for us all.
And The simple guide : xl Viper lx : I am simply doing what i do best. getting you a noobproof guide and also simplifying the adb/terminal code
All of us will take credit for the collaborating and making of this thread to help everyone unlock with no cost. What???.....Yes thats right......We broke the FTSE index by providing free unlocks! lol
Also 9 people who voted no in the poll, ad voted before we found method 2 which unlocks every sensation
METHOD 1 - USE THIS FIRST
The SIM-Unlock code location for some sensation's (NOT ALL) has been found and confirmed to work for the few users who tested it. Use method 1 below to find your unlock code
(Method 1 ADB guide in post 2 if you don't want to use Terminal Emulator or you just want to use ADB)
Requirements:
-Rooted simlocked Sensation - Enable USB debugging in Settings > Application ->Development
-Terminal Emulator (Download free from the market) or click here to download and install into your phone
Your IMEI Number (Dial "*#06#" in phone keypad to get it)
GUIDE - Method 1
1. Download Terminal Emulator from the market if you havent already done so and Run it. This should bring you a blue screen. Full screen.
2. enter the command "SU".
3. Click allow when Super user pop up appears to give it root access. (If your keyboard disappears, keep hold of menu button to bring it back up)
4. enter the command "strings -n 8 /dev/block/mmcblk0p6"
5. This should give Output a bunch of numbers like in the screenshot! IF IT SAYS STRING: NOT FOUND MOVE TO POST 2 AND USE ADB!
6. The 8 digit number above your IMEI number is your unlock code. See post 2 on how to enter it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
IF it only brings you a date above your IMEI. Then the unlock code is not present in your device. Move to Method 2
GUIDE - Method 2 - USE IF METHOD 1 FAILED!
Revolutionary achieved radio S-OFF for Sensation (among other devices) which means you can practically do whatever you want with your phone (like actually owning it). This means it makes it vulnerable to all sorts of schemes including sim-unlock. The following method is quite efficient and easy to do and can be done with the need for a computer!
Requirements:
-Rooted simlocked Sensation!
-Clockwork Recovery or Revolutionary Recovery - NEEDED FOR NANDROID BACKUP
-Titanium Backup (Download from the market if you don't have it) - YOU ONLY NEED THIS IF YOU DONT WANT TO OR CAN'T NANDROID BACKUP
WARNING!!!
Backup all your settings/apps/sms/network/APN/Data etc.
Using this method to unlock will wipe your data and apps too! (Factory Resets in other words)
But it's this method that actually resets some other things including your sim-lock status.
Guide - Method 2
1. MAKE A NANDROID BACKUP USING RECOVERY - (Completely switch off your phone, Press Volume down + Power button to get into bootloader, Volume down to recovery then press power button to get into Recovery. Volume down to "Backup and Restore" in recovery. Press Power to backup and your done!
(Make a backup in Titanium backup if you don't want to or can't nandroid backup. Menu > BAtch >Backup systems data + Apps with data)
2. Download PG58DIAG for the Sensation HERE or FROM MULTIUPLOAD
3. Copy the PG58DIAG file into the Root folder of your SD card (The main Folder of your Memory Card)
4. Turn off your phone Fully and reboot into the Bootloader/HBOOT screen (see post 2 on how to get to bootloader screen)
5. Press Volume Down to Enter DIAG - Place the phone horizontally when it asks you too. (Flat)
6. Press power button to select "Clean S58 Data
7. Press power again to "clean S58 Data".
8. POW - your unlocked! Try a SIM card from a different provider!
9. Delete the file from your SD Card (Delete PG58DIAG) and REBOOT!!
Your phone Will set up for the first time, go through it all till you get to your home screen
10. Go back into recovery and restore nandroid backup. same method as step 1 above. but instead of backup, you use restore feature
(Use Titanium Backup to restore if you used it to backup instead of Nandroid backup)(Menu > Batch > Restore System Data + Apps with user data)
Now you’re free to go! Bear in mind, though, in certain circumstances you will lose your data connectivity or network signal. You’ll just need to check your APN, network type etc. and re-enter them; Just run the nandroid restore to get everything back
Thanks to Dav22. for discovery of method 1
Dazweeja for his simple Code to find the unlock
sieempi for Method 2.
Thanks to Team Revolutionary for PG58DIAG and S-off
Don't forget to CLICK THANKS, VOTE and RATE if this guide worked for you.
don't forget to thank the above users too by clicking the links
Method 1 ADB GUIDE
METHOD 1 - ADB GUIDE- Skip steps 1 to 5! if you already have already got ADB and can get to the ADB folder through command prompt/Terminal. If your not sure follow all the steps
1. Download adb tools here: download for Windows or Linux or from attachments in the Sensation S-off guide
2. On your PC click on your local disk C: Drive (or D: drive for some) (WINDOWS users: Start > My computer > Local Disk (C)
3. Create a new folder called "adb" and extract the files from adb.zip into it. Make sure it doesn't create another folder in the adb folder when extracting
4. open command prompt (or terminal for linux) and type "cd" "followed by the path to your adb folder" (windows users can type "cd C:\adb")
5.a Ensure your phone is switched on (regular home screen) and connect it by USB in charging mode (Ensure usb debugging is on settings) OR!!!!
[ IF YOU GOT THE STRING:NOT FOUND ERROR IN METHOD 1 (terminal Emulator) REBOOT INTO RECOVERY AND CONNECT YOUR USB AND CONTINUE (Turn off your phone completely, volume down + power button, then select recovery to get into it!) ]
6. enter the command "adb shell". Your phone should display a hash sign [#] (if it doesn't then you are not rooted! - GO ROOT)
7. enter the command "SU".
8. enter the command "strings -n 8 /dev/block/mmcblk0p6"
9. This should output a bunch of details as shown in the screenshot below
10. The 8 digit number above your IMEI is your unlock code. See post 2 on how to enter it. IF it only brings you a date and your IMEI. Then the unlock code is not present in your device. Move to Method 2 in Post 1
To unlock your GSM phone with the unlock code follow these simple steps:
1. Power on your Sensation with a SIM card from an unsupported network/carrier/provider.
2. If asked, enter the PIN code of your SIM Card.
3. Enter unlock code when prompted!
FOR DUAL CDMA
How to enter the code in dual CDMA - GSM/LTE HTC Phones
1. Power on your Sensation with a SIM card from an unsupported network/carrier/provider.
2. Phone will tell you to insert an allowed SIM card and that the phone will switch back to CDMA mode.
3. Click OK.
4. Click green button to get to the main screen of the phone.
5. Click on settings.
6. Click on all settings.
7. In the personal tab click on security.
8. The phone will ask you to enter the unlock code. Enter it. Done
You hook it up again bro! I love your guides! Noobproof for sure.
Thanks VipeR strikes Again. This has worked on a few Sensations. need to verify it works on more devices and its worth a shot.!
Awesome guide.
Wonder why SH**** serials don't have this.
Wonder what the difference is.
wifiguru said:
Awesome guide.
Wonder why SH**** serials don't have this.
Wonder what the difference is.
Click to expand...
Click to collapse
They do but the location is different. As far as I'm aware I think so far the code has been found on one
Device with sh serial number. Hadn't been confirmed where. I will update if it has been found
Sent from my HTC Sensation Z710e using XDA App
Would love to figure out where.
When I search 355, all I see is what is attached. (erased full numbers just in case)
theinmoe said:
I have TMOUS. Here is dump files. File extension changed from dump to docx, so I can attache here.
Click to expand...
Click to collapse
Your simunlock code is 03139227
Please reply if this worked for you!
wifiguru said:
Would love to figure out where.
When I search 355, all I see is what is attached. (erased full numbers just in case)
Click to expand...
Click to collapse
could u do me a favour?
worked like a charm
Ok, vote Yes then please. need to know how many people this is working for!
Ive got an HT serial number, when I run the dump and search I get this back:
4109712121765 TY15KT509183 HT15VT******
numbers plus 4 letter in front of my serial number??????
joemm said:
Ive got an HT serial number, when I run the dump and search I get this back:
4109712121765 TY15KT509183 HT15VT******
numbers plus 4 letter in front of my serial number??????
Click to expand...
Click to collapse
Hmm this is working for the majority of devices, post your dump files here in a zip file please and the first 5 numbers of your IMEI *#06#
ill take a look! also what network r u on?
Your not searching serial number!
your searching IMEI number in the dumps . normally begins with 355 r something, just type in first few numbers of your IMEI, then search!
infront of your imei number is 8 digit number !
xl VipeR lx said:
Hmm this is working for the majority of devices, post your dump files here in a zip file please and the first 5 numbers of your IMEI *#06#
ill take a look! also what network r u on?
t
Click to expand...
Click to collapse
Here you go , I just edited my IMEI number thats all with five *****
My IMEI number starts with HT15Vt5*****
EDIT: nOOb mistake ..................wrong number in my search
EDIT: GOT it now, i was puting my serial number not IMEI ....been a long day.
joemm said:
Here you go , I just edited my IMEI number thats all with five *****
My IMEI number starts with HT15Vt5*****
Click to expand...
Click to collapse
LOL no.
2011/05/27 86652749 3550660405***** T-MOB010
your unlock code is 86652749, your imei is 3550660405*****, your serial number is HT15Vt5*****
So your unlocked now? if you are reply back and vote!
xl VipeR lx said:
LOL no.
2011/05/27 86652749 3550660405***** T-MOB010
your unlock code is 86652749, your imei is 3550660405*****, your serial number is HT15Vt5*****
So your unlocked now? if you are reply back and vote!
Click to expand...
Click to collapse
WORKED and voting now...
Have a SH S/N here ...How long do u think it would take to unlock us unlucky souls with an SH S/N ??!
Thanks for the guide.
No Love for me ..
Mine says ..
2011/05/27 blank 35506604******* T-MOB010
Weird And I have a HT Serial
trying now. had to turn dump to txt and i found my code.....
UPDATE:
Works it unlocked and rebooted it.
NYCguy2020 said:
Have a SH S/N here ...How long do u think it would take to unlock us unlucky souls with an SH S/N ??!
Thanks for the guide.
Click to expand...
Click to collapse
Not sure, im SH too, but i have a factory unlocked device!
This is to show you how to get Google Play on the Huawei Enjoy 5, which standard Chinese Stock ROM does not have Play store enabled.
Note: when unlocking the phone and installing custom recovery, it might mean that the OTA updates don't work anymore.
Since we have not yet had an update since I installed this, I could not check, but this is what is said in the Huawei unlock site...
Credits: my sincere thanks to andrik22, who guided me through the whole process...
Prerequisites:
Huawei Enjoy 5 phone (TIT-AL00)
Huawei Unlock tool (attached)
ADB drivers (attached)
ADB / Fastboot software (attached)
CWM Recovery file (attached)
GAPPS Pico for ARM64, Android 5.1 --> Download from Opengapps.org
Steps to complete:
1. Install ADB Drivers
2. Unzip ADB software in C:\adb
3. Unzip CWM_Recovery.img in C:\adb
4. Copy the GAPPS file into C:\adb
C:\adb should look like this now:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Now got to the phone and write down:
Settings -->about phone --> Status--> IMEI 1 + Serial Number
6. Connect phone by USB to computer
7. Enable USB debugging on phone --> slide down the notification area and touch "USB connection options", then on the bottom of the screen enable "USB Debugging"
7a. Copy the GAPPS file from C:\adb to the root of the external SD card on your phone
8. Unzip and open the Unlock tool (you might need to disable the virus checker, as this will be flagged and deleted, at least this was the case with me) --> fill in IMEI 1, get Product ID, write that down.
9. Go to the Huawei site to get your unlock code (log in with Facebook, or Huawei ID, fill in the required information product type = Smartphone, product ID = TIT-AL00, serial number from the phone, IMEI code, Product ID). Your unlock code will be below in Red)
10. Startup command prompt (Windows key + R, type cmd, enter)
11. In command prompt, type "cd \adb" to get to the adb directory
12. In command prompt check if device is recognized (typing "adb devices" in the command prompt should show you this)
13. Now reboot the phone into fastboot by typing "adb reboot bootloader"
14. This should reboot the phone into fastboot mode (black screen, only showing "fastboot>" on the bottom
15. In the command prompt, type "fastboot devices" to see if the device is recognized.
Your screen should look something like this:
The next command will unlock your phone AND make a hard reset... if any data or settings would need to be preserved, please make a backup!
16. Now type in the command prompt:"fastboot oem unlock XXXXX" where XXXX is the unlock code you got from the website
17. Then type in command prompt: "fastboot reboot". After this, your phone will reboot and reset.
18. When Phone is rebooted, make sure USB debugging is on again (same as point 7)
19. Now reboot the phone into fastboot by typing "adb reboot bootloader"
20. This should reboot the phone into fastboot mode (black screen, only showing "fastboot>" on the bottom
21. In the command prompt, type "fastboot devices" to see if the device is recognized.
22. Now we are going to flash CWM Recovery: type in command prompt: "fastboot flash recovery CWM_recovery.img"
23. reboot into recovery by typeing into command prompt: " "fastboot reboot" while holding VOL+ on the phone.
24. When the options screen on the phone appears, press VOL- to select the recovery mode. This will boot into CWM recovery.
25. In CWM recovery, select "install ZIP" and select "From Memory card" and select the Open Gapps file we have copied there in step 7a.
26 When flashing is done, type into the command prompt: "adb reboot" to reboot the phone.
This should reboot the phone. first 5 minutes it might be very slow as it is optimizing (Google) apps, but then Google Play store should be working on your phone!
Attention!
When installing SuperSU you can NOT get ROOT!!!
You will receive a cyclic reboot. And for the restoration of the phone need flash original recovery, and then install the firmware version B128 from the official site (update.zip).
Links for firmware version B128:
TWRP recovery
Original Recovery
Official page TIT-AL00
Firmware version C00B128 from the official site and mirror. Size: 1,2 Gb (The Chinese have made a mistake, inside the archive file located in the upgrade "dlaod" - is wrong, the folder should be called dload.)
Firmware version C00B132 from the official site and mirror. Size: 1,2 Gb
Firmware version C00B135 from the official site and mirror. Size: 1,2 Gb
Firmware from the official site installed only from original recovery, so if you have installed CWM recovery, you must first restore the original as it is written above, and already from it to make a clean install.
Can't open the Huawei Unlock tool...
Thanks for the guide but there's a crucial step that seems not to work: the "Huawei Unlocker.zip" tool only contains an adb.exe, fastboot.exe, and a few non-Windows-executable files (busybox and 2 .dll's) so how do we execute this tool?
gordonnorth said:
8. Unzip and open the Unlock tool (you might need to disable the virus checker, as this will be flagged and deleted, at least this was the case with me) --> fill in IMEI 1, get Product ID, write that down
Click to expand...
Click to collapse
=> How to "open the Unlock tool"? It seems to be missing from the .zip file... could you re-upload somehow?
Thanks again!
tomvanbraeckel said:
Thanks for the guide but there's a crucial step that seems not to work: the "Huawei Unlocker.zip" tool only contains an adb.exe, fastboot.exe, and a few non-Windows-executable files (busybox and 2 .dll's) so how do we execute this tool?
=> How to "open the Unlock tool"? It seems to be missing from the .zip file... could you re-upload somehow?
Thanks again!
Click to expand...
Click to collapse
Hi!
I see that I attached the wrong file here. have corrected in the meantime.
Please try the unlocker tool that is attached now.
gordonnorth said:
Hi!
I see that I attached the wrong file here. have corrected in the meantime.
Please try the unlocker tool that is attached now.
Click to expand...
Click to collapse
It worked perfectly now. Google Apps are installed. Thanks a lot, guys!
One more gotcha: the Huawei Unlocker.exe didn't work for me when executed directly from the .zip file, even though it's only one file so I expected that to work... Perhaps it self-extracts... Anyway, you need to unpack the .zip file first and then execute the unlocker .exe
; said:
when I flash the gapps.zip from sdcard.
cwm told me the signature verification faild...
maybe I should try another gapps?
Click to expand...
Click to collapse
; said:
I tried 5 gapps blow but none of them works...
Click to expand...
Click to collapse
Found the problem. and finnaly it works.
The first time of the CWM installation failed. ( but adb told me OK).
so I just flash CWM again to solve the problem.
Many thanks.
so many chinese user also wanna to use gapps, even the Gov. banned google services here.
Hope there's a way to root the device , to delete those useless pre-installed apps.
Thanks again.
different huawei emuı page
hi my friends,
there is a problem about huawei emui page
I check the your advice but When I want to appliacaiton this step, I see different page in web site
and than I can not submit this step I don't take unlock code.
what is the problem pls help me !!
thanks
petere15 said:
hi my friends,
there is a problem about huawei emui page
I check the your advice but When I want to appliacaiton this step, I see different page in web site
and than I can not submit this step I don't take unlock code.
what is the problem pls help me !!
thanks
Click to expand...
Click to collapse
Hi petere15,
did you go to this website? it still seems fine to me?
https://emui.huawei.com/en/plugin.php?id=unlock&mod=detail
The same model TIT-AL00 announced to India with the name of Honor Holly 2 Plus.
Review
This means that you can install the firmware, which has services Googe.
andrik22 said:
The same model TIT-AL00 announced to India with the name of Honor Holly 2 Plus.
Review
This means that you can install the firmware, which has services Googe.
Click to expand...
Click to collapse
Hey Andrik,
do you know where we can download that firmware?
and did you test that already? might be good to have a more westernized ROM available, so also the EMUI badges might work for whatsapp for example...
gordonnorth said:
Hey Andrik,
do you know where we can download that firmware?
and did you test that already? might be good to have a more westernized ROM available, so also the EMUI badges might work for whatsapp for example...
Click to expand...
Click to collapse
Today just announced!
On sale from 15 February. I think the firmware will be closer to the date of sale.
Firmware appear on this page.
The same phone will be sold in Europe, called Huawei Y6 Pro.
http://www.notebookcheck.com/Huawei...er-unteren-Mittelklasse-geleakt.156905.0.html
http://www.allmobilearea.com/huawei-y6-pro/
User guide in English and Mirror.
hi,
im not expert for phones so i need little help. Problem begine on geting unlock key.
My Huawei page look diferent , don't have product type.
Cant paste link coz im new here: h t t p://imgur.com/nGkL3R1.
Any idea what to do next?
in product model i try to write" huawei tit-al00", only "tit-al 00" and i get the same message.
Sorry on my bad english, hope someone will understand my problem.
thx
GONF said:
hi,
im not expert for phones so i need little help. Problem begine on geting unlock key.
My Huawei page look diferent , don't have product type.
Cant paste link coz im new here: h t t p://imgur.com/nGkL3R1.
Any idea what to do next?
in product model i try to write" huawei tit-al00", only "tit-al 00" and i get the same message.
Sorry on my bad english, hope someone will understand my problem.
thx
Click to expand...
Click to collapse
Manufacturer again changed the method of obtaining the unlock code.
You need to go to the phone account Huawei. For example, Huawei club, HiApp or Huawei Cloud+.
The report said that you did not go to these applications for more than 14 days.
The second option - for unlock to write their e-mail data (down - contact us).
thx for answering, first solution didnt work, so i sent mail, hope i will get some positive answer.
Hmm, still no answer from huawei tehnical support.
Anyone have some expirience with them?
Or, is ther any other solution for my problem?
pls anyone.... girl will cut my ..... if i don fix her mobile
GONF said:
Hmm, still no answer from huawei tehnical support.
Anyone have some expirience with them?
Or, is ther any other solution for my problem?
pls anyone.... girl will cut my ..... if i don fix her mobile
Click to expand...
Click to collapse
Unfortunately, there is only a version of the installation software VPN, included in the service with Huawei phone with the expectation of 14 days.
I have not tested it should work in theory.
Perhaps you can write in support of Huawei in your country - that they may request an unlock code from colleagues in China.
Hi, I still have not solved my problem, so I have one question.
Will it be possible in the near future root this device?
Or i can trow it in the trash.
GONF said:
Hi, I still have not solved my problem, so I have one question.
Will it be possible in the near future root this device?
Or i can trow it in the trash.
Click to expand...
Click to collapse
Even if it will be able to get root, too, need to unlock the bootloader on it.
You have tried to write an e-mail?
Send an email to [email protected] Email them the following. They usually email you back and tell you to do go online to unlock your bootloader and it should work on the website, or never email you back:
Hello. I keep getting an error when trying to unlock my phone on the unlock page.
Model: TIT-AL00 (Or whatever model you have)
Serial: Put in your phones serial number here. (You get this in About phone, Status)
IMEI: Put in your phones IMEI number here. (You get this in About phone, Status, it's IMEI1)
Product ID: (Go into your phone dialer and dial *#*#1357946#*#* and it will give you your Product ID, or use Huawei Unlocker)
!!! YOUR WARRANTY IS NOW VOID !!!
THIS TOOL IS FOR CUBOT NOTE PLUS ONLY.
neither I nor the XDA Forum is responsible for your phone brick or your cat triggers an atomic apocalypse. YOU has been responsible for your phone and you are doing everything at your own risk.
This is a tool for rooting the CUBOT NOTE PLUS ONLY.
NOTE: THIS TOOL IS IN ALPHA STAGE
RoCuNo+_v0.3 is online.
Downloads see post 2
This tool can root your Cubot Note Plus and patch your boot.img for working with Magisk.
this tool can make this in seperate steps or All-In-One. For now the bootloader must stay UNLOCKED for root to work.
A guide to doing this by yourself with adb is also in this post.
NOTE: ALL YOUR DATA GET LOST. SAVE YOUR IMPORTANT DATA FIRST. (Videos, Pictures, Music and all you can save.)
What this tool can do:
Unlock/Relock your Bootloader
Root/Unroot your Cubot Note Plus (Unroot dont work for now)
[*]Make a Dump of your Boot Partition as boot.img
Install MagiskManager-v5.4.3 and Magisk-v14.0
Please download the attached zip and unzip it somewhere and rightclick on RoCuNo+_V*.bat and start as Administrator.
Read all carefully and choose your option. Follow the instructions on screen STEP BY STEP!!!
Better way is to choose the AIO because that makes all for you except a few steps.
Downloads see post 2
GUIDE
OEM UNLOCK + ROOT + MAGISKMANAGER APP
01. make sure you have installed ADB drivers
02. enable "Developer Options" Menu ("Menu --> Settings --> About Phone" tap "Built Number" 7 times.)
03. enable "USB DEBUGGING" and "OEM UNLOCKING" (Go to "Menu --> Settings --> Developer Options")
04. enable "UNKNOWN SOURCES" in "Menu --> Settings --> Security"
05. connect USB cable to PHONE and then connect to PC
06. make sure all Drivers are installed.
07. go in RoCuNo+ Directory on PC
08. press Shift + Right Mouse Click
09. Open Command Prompt here
10. type
Code:
adb reboot-bootloader
11. type [ODE]fastboot oem unlock[/CODE]NOTE: ALL YOUR DATA WILL BE DELETED
12. press VOL+ Button on phone to oem unlock
13. type
Code:
fastboot flash boot patched_boot.img
14. type
Code:
fastboot reboot
15. if you have unlocked your bootloader, make your setup
16. enable "Developer Options" Menu ("Menu --> Settings --> About Phone" tap "Built Number" 7 times.)
17. enable "USB DEBUGGING" (Go to "Menu --> Settings --> Developer Options")
18. type
Code:
adb install -r -d -g MagiskManager-v*.*.*.apk (set the Version numbers for *)
OEM LOCK
01. make sure you have installed ADB drivers
02. enable "Developer Options" Menu ("Menu --> Settings --> About Phone" tap "Built Number" 7 times.)
03. enable "USB DEBUGGING" and "OEM UNLOCKING" (Go to "Menu --> Settings --> Developer Options")
04. enable "UNKNOWN SOURCES" in "Menu --> Settings --> Security"
05. connect USB cable to PHONE and then connect to PC
06. make sure all Drivers are installed.
07. go in RoCuNo+ Directory on PC
08. press Shift + Right Mouse Click
09. Open Command Prompt here
10. type "adb reboot-bootloader"
11. type "fastboot oem lock"
12. press VOL+ Button on phone to oem lock
13. type "fastboot reboot"
UNROOT
01. make sure you have installed ADB drivers
02. enable "Developer Options" Menu ("Menu --> Settings --> About Phone" tap "Built Number" 7 times.)
03. enable "USB DEBUGGING" and "OEM UNLOCKING" (Go to "Menu --> Settings --> Developer Options")
04. enable "UNKNOWN SOURCES" in "Menu --> Settings --> Security"
05. connect USB cable to PHONE and then connect to PC
06. make sure all Drivers are installed.
07. Download SP Flashtool and Firmware for Cubot Note Plus
08. Start SP Flashtool and choose the MT6737T_Android_scatter.txt from the Cubot Note Plus Firmware Folder.
09. Turn off the Cubot Note Plus.
10. Click on Downloadbutton and connect the Cubot Note Plus to PC.
NOTE: ALL YOUR DATA WILL BE ERASED. MAKE A BACKUP IF YOU NEED.
11. After Flashing is complete, reboot Phone.
Old Guide
Save your data.
Connect your phone to PC and make sure all drivers are installed. (Boot up to normal system, recovery and fastboot to get sure.)
Open a CMD Prompt on your PC and switch to Directory where you have unzipped the RoCuNo+. (e.g. C:\Users\YourName\Desktop\RoCuNo+ or You can go to RoCuNo+ folder and Shift+Rightclick on empty space and click "open Command Prompt here".)
Type:
Code:
adb reboot-bootloader
Than:
Code:
fastboot oem unlock
NOTE: ALL YOUR DATA WILL BE DELETED
Press VOL+ on Phone if asked
wait for device for unlock
Type:
Code:
fastboot reboot
Setup your phone until you come to system.
Enable "Developer Options" Menu. Go to Menu --> Settings --> About Phone and tap Built Number 7 times until a message appears that you are now an Developer.
Enable USB DEBUGGING and OEM UNLOCKING in Menu --> Settings --> Developer Options.
Enable UNKNOWN SOURCES in Menu --> Settings --> Security
Copy MTK-Engineering-Mode.apk and MagiskManager-v5.4.0.apk on your and install this to apps.
open the MTK-Engineering-Mode app tap on MTK Settings and swipe to Log and Debugging.
Tap on User2Root and than the Root button.
NOTE: UNPLUG AND RECONNECT YOUR PHONE. DONT CLOSE THIS APP OR DO SOMETHING ON THE PHONE. YOU LOSE YOUR ROOT IF YOU DO SOMETHING.
Go back to CMD Prompt on PC and type:
Code:
adb root
adb shell dd if=/dev/block/mmcblk07p of=/sdcard/boot.img
Now open MagiskManager app and tap the Install button.
Choose to inject in boot.img
Point Magisk to the boot.img.
after Magisk has succssesfully patched the boot.img it will copy it to /sdcard/MagiskManager/patched_boot.img.
Copy your boot.img from sdcard AND the patched_boot.img from sdcard/MagiskManager to the RoCuNo+ folder on your PC.
Go to CMD Prompt and type:
Code:
adb reboot-bootloader
than type:
Code:
fastboot flash boot patched_boot.img
when flashing is ready, type:
Code:
fastboot reboot.
on phone go to MagiskManager app and check if Magisk and Root are on green state.
You succssesfully have rooted your Cube Note Plus.
Take care of the boot.img and the patche_boot.img in case we need them on some day.
DONT RELOCK YOUR PHONE BECAUSE YOU CANT WRITE ON /SYSTEM PARTITION WITH LOCKED BOOTLOADER. (for now.)
I hope that helps many people with his/her phone and maybe someone can make TWRP or a Custom Rom for our phone. Now the Door is Open.
if someone found better solution for some tasks here please let us know.
Changelog
RoCuNo+ v0.3
Delet the Unroot Section because it doesent work for now.
update Magisk Manager App to 5.4.3.
Update Guide.
Update patched_boot.img.
RoCuNo+ v0.2
complete rework.
all should now work.
now the original verified-boot.img from Cubot is implemented. so root and unroot works now.
ive patched the original verified-bood.img with magisk so no boot.img dump has to be made.
the tool now detects what state you are and boots the state needed for his job.
only magisk manager app has to be installed on device and the tool do this for you.
the tool detects if you are already oem unlocked or not. so if you already unlocked you dont
need to do that again. it also detects in witch state your phone and boots the right mode.
Credits to XDA-Developer Schwester_Gabi (https://forum.xda-developers.com/member.php?u=5264039) and the Flampinko.IT Team ([email protected])
you can use this tool on your own risk but its not allowed to share this tool in other forums or blogs or something. but you can write about this tool and link
than over to the XDA-Developer Forum under (https://forum.xda-developers.com/android/general/guide-cubot-note-plus-mtk6737t-root-t3695272)
it is also not allowed to copy the code or change anything in this programm. Only Schwester_Gabi or the Flampinko.IT Team is allowed to change the code.
If you have any Ideas to implement in this tool than post it over to XDA-Developers Forum (https://forum.xda-developers.com/android/general/guide-cubot-note-plus-mtk6737t-root-t3695272)
or send us an Email ([email protected]). If you like our work please make a donation to help us.
https://www.paypal.com/cgi-bin/webscr?cmd=_s-xclick&hosted_button_id=ZXVV3MZX2NVK6
please respect the developers work and stick to the rules.
Credits and special thanks to:
topjohnwu for the awesome Magisk
themonsterit for MTK-Engineering-Mode App
Schwester_Gabi for finding the way and coding the RoCuNo+ programm
all the people who write solutions for problems that i read to find the way too root.
XDA-Developer Team to giving us such a great Platform to share our stuff with the world.
Cubot Note Plus Stock Rom:
V8:
Mirror 1
V7:
Mirror 1 / Mirror 2
SP Flash Tool for Cubot Note Plus Stock Rom:
Mirror 1 / Mirror 2
Cubot Note Plus Stock Scatter File for flashing:
Mirror 1 / Mirror 2
RoCuNo+_v0.1(Alpha):
Mirror 1 / Mirror 2
RoCuNo+_v0.2:
Mirror 1 / Mirror 2
RoCuNo+_v0.3:
Mirror 1
Problems:
i got some problems with dumping boot.img. the partiton size is 16M and the dd dump is also 16M but if i try to flash it back fastboot says the file is to large for partition. thats why unroot doesent work for now. Magisk patch the boot.img and resize them to 8M. than flashing works fine and all works. if someone can point me in the right direction would be very nice. if you have some questions please write here or pm me.
if someone can make a scatter file for this phone or had the scatter file it would be nice to share so we can try to backup the phone with SP Flash Tool. thanks.
if you found some bugs please tell it here so i can fix it.
Nice
Thanks for this great work, worked flawlessly. Just wondered, now we've got this root, is there any custom recovery we can install for it? (I realise many things will be available through Magisk's modules already, but still just wondered.)
Matthius said:
Thanks for this great work, worked flawlessly. Just wondered, now we've got this root, is there any custom recovery we can install for it? (I realise many things will be available through Magisk's modules already, but still just wondered.)
Click to expand...
Click to collapse
not now. i hope that someone can make an TWRP or CWM for the Cubot and share it with us.
Matthius said:
Thanks for this great work, worked flawlessly. Just wondered, now we've got this root, is there any custom recovery we can install for it? (I realise many things will be available through Magisk's modules already, but still just wondered.)
Click to expand...
Click to collapse
did you use the RoCuNo+ Programm or have you done all by yourself ? what do you use ? step by step or the AIO routine ?
Schwester_Gabi said:
did you use the RoCuNo+ Programm or have you done all by yourself ? what do you use ? step by step or the AIO routine ?
Click to expand...
Click to collapse
I had already unlocked the bootloader myself prior to this, looking for a way to root it before I saw this article (I gather this is the first available root method for this device), and also manually installed MagiskManager and the MTK-Engineering-Mode apk's and from then on I used the ruCuNo+ bat to complete it.
I followed stage 6, then 7, then 3. Pointed the Magisk to the original boot img, got it patched, sent it to PC and flashed the boot image with ADB. After turning on the phone, Magisk ended up with two green ticks so everything was good to go.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Matthius said:
I had already unlocked the bootloader myself prior to this, looking for a way to root it before I saw this article (I gather this is the first available root method for this device),
Click to expand...
Click to collapse
yes it is. i searched over a week to find a root solution but nothing found. so i make it by my self and want to share this with the world :highfive:
Matthius said:
and also manually installed MagiskManager and the MTK-Engineering-Mode apk's and from then on I used the ruCuNo+ bat to complete it. I followed stage 6, then 7, then 3. Pointed the Magisk to the original boot img, got it patched, sent it to PC and flashed the boot image with ADB. After turning on the phone, Magisk ended up with two green ticks so everything was good to go.
Click to expand...
Click to collapse
thats also a way :good: maybe i implement this for users who already unlockt the bootloader. then the the phone must not be factory reset again. :good: thanks for telling me this way i dont think of bevor
Schwester_Gabi said:
yes it is. i searched over a week to find a root solution but nothing found. so i make it by my self and want to share this with the world :highfive:
thats also a way :good: maybe i implement this for users who already unlockt the bootloader. then the the phone must not be factory reset again. :good: thanks for telling me this way i dont think of bevor
Click to expand...
Click to collapse
No worries, great work - hopefully, we may see some custom recovery to come in the future from someone. Wish this phone actually had its own page on XDA, but I doubt it has enough widespread support for that, who knows.
Matthius said:
No worries, great work - hopefully, we may see some custom recovery to come in the future from someone. Wish this phone actually had its own page on XDA, but I doubt it has enough widespread support for that, who knows.
Click to expand...
Click to collapse
Yes. custom recovery for the phone would be great. if I knew better, I would make one myself. but I've read a lot. maybe I'll try it in future to make one.
i think this phone dont get his own page. but maybe the Cubot vendor get his own where we can put all related Cubot threads together in his own sub section. :good:
i got a error after "fastboot oem unlock" -> "FAILED (remote:Unlock operation is not allowed)". i think, bootloader is not unlocked, what can i do?
oops: had forget "OEM UNLOCKING in DevMenu"
spunky1a said:
i got a error after "fastboot oem unlock" -> "FAILED (remote:Unlock operation is not allowed)". i think, bootloader is not unlocked, what can i do?
oops: had forget "OEM UNLOCKING in DevMenu"
Click to expand...
Click to collapse
yes. that was the point. :good:
I think the sequence in the Guide is a bit wrong. In the Guide I read:
Schwester_Gabi said:
...
Type:
Code:
adb reboot-bootloader
Than:
Code:
fastboot oem unlock
NOTE: ALL YOUR DATA WILL BE DELETED Press VOL+ on Phone if asked wait for device for unlock...
... (this comes now after)
Enable USB DEBUGGING and OEM UNLOCKING in Menu --> Settings --> Developer Options
...
Click to expand...
Click to collapse
If I follow this I get (in very small fonts) as another user here in this thread:
Unlock failed...return to fastboot in 3s
Click to expand...
Click to collapse
And no unlock of the bootloader seems possible.
Because first I need to do OEM UNLOCKING in the Dev. Options, which seems very clear. Only after I can fastboot oem unlock
What I further not quite understand in this post, is it either the Guide or the Batchfile I have to follow? Or is it a mixture of both what I need to do?
As I think the Batchfile cannot enable the Developer Tools in the System, or?
Lastly and most important: on my phone I don't see a mmcblk07p only a mmcblk0p7, so this throws an error:
Schwester_Gabi said:
...
adb shell dd if=/dev/block/mmcblk07p of=/sdcard/boot.img
...
Click to expand...
Click to collapse
I guess that mmcblk0p7 is ment, so I did a dd with mmcblk0p7, and I let patch this file with Magisk to the file: patched_boot.img
But here I am very not sure and if I flash now a wrong img-file with this:
Schwester_Gabi said:
...
fastboot flash boot patched_boot.img
...
Click to expand...
Click to collapse
I strongly guess that is it with my new phone
So could you please confirm that it was just a typo in the first post here?
How can I know which of these files in /dev/block is the boot.img?
Thank!!!
francwalter said:
I think the sequence in the Guide is a bit wrong. In the Guide I read:
...
Type: Than:
If I follow this I get (in very small fonts) as another user here in this thread:
And no unlock of the bootloader seems possible.
Because first I need to do OEM UNLOCKING in the Dev. Options, which seems very clear. Only after I can fastboot oem unlock
Click to expand...
Click to collapse
For this Problem the batch says first enable dev options and OEM unlock and than go to next step.
francwalter said:
What I further not quite understand in this post, is it either the Guide or the Batchfile I have to follow? Or is it a mixture of both what I need to do?
As I think the Batchfile cannot enable the Developer Tools in the System, or?
Lastly and most important: on my phone I don't see a mmcblk07p only a mmcblk0p7, so this throws an error:
I guess that mmcblk0p7 is ment, so I did a dd with mmcblk0p7, and I let patch this file with Magisk to the file: patched_boot.img
But here I am very not sure and if I flash now a wrong img-file with this:
I strongly guess that is it with my new phone
So could you pleas confirm that it was just a typo in the first post here?
How can I know which of these files in /dev/block is the boot.img?
Thank!!!
Click to expand...
Click to collapse
Yes. Its a typo. You can flash it.
Btw i am on the way to rework the whole Programm for better use and better instructions. Give me some time because iam very busy at the moment. But I will update it soon.
And remember its an 0.1ALPHA for now. So its not perfect :angel:
Oh Great! It works
Thank a lot for your work!!!
As a noob, I did not get what to do after installing the Magisk manager. So I have it installed, but it shows no root. How can I then install the root?
I used the "RoCuNo+_v0.2.bat" in admin mode and although I got through the unlock and root, I am stuck on what to do on Magisk in the phone.
I was able to root my galaxy tab, but perhaps I am too noob for these instructions?
(Btw while booting I get the "this phone is unlocked and cannot be trusted" text)
Ran into a bit of an issue here, I received an official OTA so I uninstalled Magisk by clicking uninstall within the APK, now my phone is stuck on the boot logo. I've tried to flash the original boot img, but I can't get into the system to confirm flashing it on the device. It displays under <adb devices> but when issuing the <fastboot flash boot> command it says <waiting for any device> and nothing occurs.
Not sure how to proceed without wiping the whole thing. Anything I can try?
So I did a factory reset and used the "RoCuNo+_v0.2.bat" again as follows:
First enabled developer mode, USB Debugging unknown sources, OEM unlock
Then ran the tool:
1 - unlock bootloader - success
3 - root - success
5 - install magisk - here the phone first boots, then it erases data, then does again all the "setup your phone, wifi, accounts etc"
"Orange state - this device is unlocked..." appears in the boot
Magisk is not installed in the apps.
OEM unlock is greyed out (but enabled)
So the tool worked differently, or I am missing something.
Perhaps there are new versions of this phone?
...aaaand it's rooted.
I did everything again using the adb -command instructions.
So did not use the .bat tool.
Used the step-by-step instructions.
Thanks a lot! Finally I can use macrodroid properly.
Unlike previously released Qualcomm based Nokia phones, Nokia X5 uses MediaTek Helio P60 processor.
However, unlike Nokia 3, it no longer uses authentication file, this will make unbrick easier.
After you read the full guide, you should understand how to unbrick your phone.
This guide should work on both 64-bit Linux distro and Windows operating system.
And this guide is simplified than previous guide to ensure your phone will get newer updates.
中文版教程请看这里：https://hikaricalyx.com/2018/10/25/how-to-convert-nokia-x5-to-global-and-unbrick/
Click to expand...
Click to collapse
What you need to have:
- MTK Smart Phone Flash Tool, which you can download from https://spflashtool.com/download/
- Android Platform Tools
- For Windows users, patched OST LA: https://drive.google.com/open?id=1n91aYT9Di6_v4F3Wjlv8TjfeLc64AcYA and MediaTek USB Port driver, which is easy to find
- Nokia X5 Chinese firmware and Global conversion firmware: https://fih-firmware.hikaricalyx.com/fihsw_en.html
Part 1: DO FULL BACKUP
Because few critical partitions are included in this backup, this will ensure you can restore them.
Download "PDA-114A-0-00WW-B01" and extract it.
Open Smart Phone Flash Tool, choose the Download Agent file and Scatter File in the unpacked PDA-1100 firmware.
DO NOT USE DOWNLOAD AGENT FROM THE FLASH TOOL ITSELF!
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Then pick "Readback" tab, add a category.
Double click this category, and choose the location you want to save the backup.
Use any text editor to open the scatter file, and find "userdata". You'll need the start address of userdata as the length of the full backup.
After it properly set, click "Read Back", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
Disconnect your phone when procedure completed.
Part 2: Flash PDA-1100 global firmware
Return to download tab, choose "Firmware Upgrade" in the download options, click "Download", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
If you just want to unbrick it as Chinese firmware, double click the Location of "lk_a", and choose "PDA-0-102A-00CN-lk.img" before you "Download", or you will unable to install later OTA updates.
Because it flashes service lk by default.
Click to expand...
Click to collapse
Part 3: Modify SKUID and flash lk
Trigger your phone to Fastboot mode.
You can type this command then connect your powered off phone:
Note: If you're using fastboot included in OST LA, use .\fastboot-android instead of .\fastboot
Click to expand...
Click to collapse
Code:
.\fastboot reboot-bootloader
Type this command to confirm your phone's Serial Number, in this example the serial number is PDAGAM0123456789:
Code:
PDAGAM0123456789 fastboot
Google a website to calculate the md5 checksum of the serial number, for example, the md5 checksum of PDAGAM0123456789 is bb1bfc95418f51dc906462554d71313a.
Now type following command to grant service permission:
Code:
.\fastboot --set-active=a
.\fastboot reboot-bootloader
.\fastboot oem dm-verity (your_md5_checksum)
In this example:
Code:
.\fastboot --set-active=a
.\fastboot reboot-bootloader
.\fastboot oem dm-verity bb1bfc95418f51dc906462554d71313a
Type following commands to confirm and modify SKUID. Following commands are case sensitive:
Code:
.\fastboot oem CustomerSKUID get
.\fastboot oem CustomerSKUID set 600WW
.\fastboot oem CustomerSKUID get
Type following commands to reflash stock lk and reboot:
Code:
.\fastboot flash lk_a G:\PDA-114A-0-00WW-B01_unpacked\PDA-0-114A-00WW-lk.img
.\fastboot reboot
Part 4: Install PDA-209B update manually.
Download this package, and rename it to "PDA-209B-0-00WW-B06-update.zip", place it to root directory of internal storage and dial *#*#874#*#* to update.
https://android.googleapis.com/pack.../b1ebc1be5c4b01109fc3c4dea515e8286904fad0.zip
Old ota packages:
https://tpedutw-my.sharepoint.com/:...hBsIjYfYvl9dsBMabfvVPHJU5mJloVo2qIKw?e=TexpIz
That's it.
Is it bootloader unlockable? Still finding out.
Special thanks to:
@blackpanther0582 for PDA-021G firmware
givemerom for PDA-1100 firmware
Someone for Nokia 5.1 Plus firmware dumping
Someone for Nokia X5 device testing
Thank you
Thank you for sharing this tutorial. But how to unlock Nokia x5 bootloader? It needs unlocked bootloader right?
Nokiyem said:
Thank you for sharing this tutorial. But how to unlock Nokia x5 bootloader? It needs unlocked bootloader right?
Click to expand...
Click to collapse
Nope, bootloader unlock is not required.
You can just convert your phone, that's it.
Thanks for your sharing! May I know if I want to convert back to Chinese firmware, only I need to do is finishing "Part 2: Reflash Chinese PDA-021G firmware“ correct?
the first, in step 1, the backup cannot complete and the message show "aborted".
The second, in step 2, I cannot extract the nb0 file. please extract and upload the zip file.
thanks very much!
I want too
wylwddjz said:
Thanks for your sharing! May I know if I want to convert back to Chinese firmware, only I need to do is finishing "Part 2: Reflash Chinese PDA-021G firmware“ correct?
Click to expand...
Click to collapse
I want too, does I need to choose firmware upgrade or download only on part 2?
hikari_calyx said:
Unlike previously released Qualcomm based Nokia phones, Nokia X5 uses MediaTek Helio P60 processor.
However, unlike Nokia 3, it no longer uses authentication file, this will make unbrick easier.
After you read the full guide, you should understand how to unbrick your phone.
This guide should work on both 64-bit Linux distro and Windows operating system.
What you need to have:
- MTK Smart Phone Flash Tool, which you can download from https://spflashtool.com/download/
- Android Platform Tools
- For Windows users, patched OST LA: https://drive.google.com/open?id=1n91aYT9Di6_v4F3Wjlv8TjfeLc64AcYA and MediaTek USB Port driver, which is easy to find
- Nokia X5 Chinese firmware and Global conversion firmware: https://hikaricalyx.box.com/s/z3s5alma4uhqftsbdo5pl072f0ec9t8z
Part 1: DO FULL BACKUP
Because few critical partitions are included in this backup, this will ensure you can restore them.
Download PDA-021G firmware and unpack it by using nb0 utils with this guide: https://forum.xda-developers.com/nokia-7-plus/how-to/workaround-flashing-oreo-firmware-t3793791
Open Smart Phone Flash Tool, choose the Download Agent file and Scatter File in the unpacked PDA-021G firmware.
DO NOT USE DOWNLOAD AGENT FROM THE FLASH TOOL ITSELF!
Then pick "Readback" tab, add a category.
Double click this category, and choose the location you want to save the backup.
Use any text editor to open the scatter file, and find "userdata". You'll need the start address of userdata as the length of the full backup.
After it properly set, click "Read Back", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
Disconnect your phone when procedure completed.
Part 2: Reflash Chinese PDA-021G firmware
Return to download tab, choose "Firmware Upgrade" in the download options, click "Download", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
Part 3: Modify SKUID
Trigger your phone to Fastboot mode.
You can type this command then connect your powered off phone:
Code:
.\fastboot reboot-bootloader
Type this command to confirm your phone's Serial Number, in this example the serial number is PDAGAM0123456789:
Code:
PDAGAM0123456789 fastboot
Google a website to calculate the md5 checksum of the serial number, for example, the md5 checksum of PDAGAM0123456789 is bb1bfc95418f51dc906462554d71313a.
Now type following command to grant service permission:
Code:
.\fastboot oem dm-verity (your_md5_checksum)
In this example:
Code:
.\fastboot oem dm-verity bb1bfc95418f51dc906462554d71313a
Type following commands to confirm and modify SKUID. Following commands are case sensitive:
Code:
.\fastboot oem CustomerSKUID get
.\fastboot oem CustomerSKUID set 600WW
.\fastboot oem CustomerSKUID get
Type following command and disconnect your phone to power off your phone:
Code:
.\fastboot oem HALT
Part 4: Flash Global PDA-101D firmware I provided
Download PDA-101D firmware and extract it.
Open Smart Phone Flash Tool, choose Download Agent and Scatter file in PDA-101D firmware, choose "Firmware Upgrade" in the download options, click "Download", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
That's it.
Is it bootloader unlockable? Still finding out.
Special thanks to:
@blackpanther0582 for PDA-021G firmware
Someone for Nokia 5.1 Plus firmware dumping
Someone for Nokia X5 device testing
Click to expand...
Click to collapse
Android oen is error Update OTA
How to fix pl.thank
I tried.
The same problem.
Android oen is error Update OTA
How to fix pl.thank
4GB RAM/64GB storage
will this work with 4GB/64GB version?
anyone success ?
hi.. i had global version Nokia 5.1 Plus, can i flash it with chinese rom ?
Android Platform Tools Link??? How to install??
please update newer version.. i cant update it with OTA update... :/ i dont know why but its working fine last update is sept.5 2018
hikari_calyx said:
Unlike previously released Qualcomm based Nokia phones, Nokia X5 uses MediaTek Helio P60 processor.
However, unlike Nokia 3, it no longer uses authentication file, this will make unbrick easier.
After you read the full guide, you should understand how to unbrick your phone.
This guide should work on both 64-bit Linux distro and Windows operating system.
And this guide is simplified than previous guide to ensure your phone will get newer updates.
What you need to have:
- MTK Smart Phone Flash Tool, which you can download from https://spflashtool.com/download/
- Android Platform Tools
- For Windows users, patched OST LA: https://drive.google.com/open?id=1n91aYT9Di6_v4F3Wjlv8TjfeLc64AcYA and MediaTek USB Port driver, which is easy to find
- Nokia X5 Chinese firmware and Global conversion firmware: https://tpedutw-my.sharepoint.com/:...dFks--5G6V4vYBGTwLw1BsthbtIuJqMUN3tQ?e=wOfytH
Part 1: DO FULL BACKUP
Because few critical partitions are included in this backup, this will ensure you can restore them.
Download "PDA-1100-0-00WW-B01_unpacked.7z" and extract it.
Open Smart Phone Flash Tool, choose the Download Agent file and Scatter File in the unpacked PDA-1100 firmware.
DO NOT USE DOWNLOAD AGENT FROM THE FLASH TOOL ITSELF!
Then pick "Readback" tab, add a category.
Double click this category, and choose the location you want to save the backup.
Use any text editor to open the scatter file, and find "userdata". You'll need the start address of userdata as the length of the full backup.
After it properly set, click "Read Back", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
Disconnect your phone when procedure completed.
Part 2: Flash PDA-1100 global firmware
Return to download tab, choose "Firmware Upgrade" in the download options, click "Download", then power off your phone and connect your phone to PC with both volume keys pressed and holded.
When you see a progress bar moving, you can release both keys and wait for the procedure complete.
Part 3: Modify SKUID and flash lk
Trigger your phone to Fastboot mode.
You can type this command then connect your powered off phone:
Code:
.\fastboot reboot-bootloader
Type this command to confirm your phone's Serial Number, in this example the serial number is PDAGAM0123456789:
Code:
PDAGAM0123456789 fastboot
Google a website to calculate the md5 checksum of the serial number, for example, the md5 checksum of PDAGAM0123456789 is bb1bfc95418f51dc906462554d71313a.
Now type following command to grant service permission:
Code:
.\fastboot oem dm-verity (your_md5_checksum)
In this example:
Code:
.\fastboot oem dm-verity bb1bfc95418f51dc906462554d71313a
Type following commands to confirm and modify SKUID. Following commands are case sensitive:
Code:
.\fastboot oem CustomerSKUID get
.\fastboot oem CustomerSKUID set 600WW
.\fastboot oem CustomerSKUID get
Type following commands to reflash stock lk and reboot:
Code:
.\fastboot flash lk_a G:\PDA-1100-0-00WW-B01_unpacked\PDA-0-1100-00WW-lk.img
.\fastboot reboot
Part 4: Install PDA-114A update manually.
Download the update package "PDA-114A-0-00WW-B03-1100-0-00WW-B01-update.zip", copy it to root directory of internal storage, then dial *#*#874#*#* to update.
This can be downloaded from here:
https://tpedutw-my.sharepoint.com/:...hBsIjYfYvl9dsBMabfvVPHJU5mJloVo2qIKw?e=TexpIz
That's it.
Is it bootloader unlockable? Still finding out.
Special thanks to:
@blackpanther0582 for PDA-021G firmware
givemerom for PDA-1100 firmware
Someone for Nokia 5.1 Plus firmware dumping
Someone for Nokia X5 device testing
Click to expand...
Click to collapse
how to go back to nokia x5
taovanluc said:
Android oen is error Update OTA
How to fix pl.thank
Click to expand...
Click to collapse
eprot12 said:
please update newer version.. i cant update it with OTA update... :/ i dont know why but its working fine last update is sept.5 2018
Click to expand...
Click to collapse
I've updated the new guide.
Now PDA-1100 build should be able to install newer updates.
hoangkyo555 said:
how to go back to nokia x5
Click to expand...
Click to collapse
Download an unpack the PDA-102A-0-00CN-B07 firmware with nb0 tools developed by @heineken78
When you change the SKUID, change it to 600CN instead of 600WW, and the lk filename is different from global PDA-1100 as you will find out.
hoangkyo555 said:
Android Platform Tools Link??? How to install??
Click to expand...
Click to collapse
This should be the basis of working on Android phones.
https://developer.android.com/studio/releases/platform-tools
thirakun said:
hi.. i had global version Nokia 5.1 Plus, can i flash it with chinese rom ?
Click to expand...
Click to collapse
Yes you can, but you need to unpack PDA-102A-0-00CN-B07.nb0 and follow the guide, but change the SKUID to 600CN instead of 600WW.
And you need to flash a different lk file which you'll find out.
Use this tool to unpack nb0: https://forum.xda-developers.com/android/general/nb0-unpacker-packer-tool-t3699464
hikari_calyx said:
Yes you can, but you need to unpack PDA-102A-0-00CN-B07.nb0 and follow the guide, but change the SKUID to 600CN instead of 600WW.
And you need to flash a different lk file which you'll find out.
Use this tool to unpack nb0: https://forum.xda-developers.com/android/general/nb0-unpacker-packer-tool-t3699464
Click to expand...
Click to collapse
.\fastboot oem dm-verity bb1bfc95418f51dc906462554d71313a
When run command above will show error message in below...
FAILED (remote: unknown command)
Finished. Total time: 0.002s
Is this command required? or I can skip it?
hikari_calyx said:
Yes you can, but you need to unpack PDA-102A-0-00CN-B07.nb0 and follow the guide, but change the SKUID to 600CN instead of 600WW.
And you need to flash a different lk file which you'll find out.
Use this tool to unpack nb0: https://forum.xda-developers.com/android/general/nb0-unpacker-packer-tool-t3699464
Click to expand...
Click to collapse
this one right?
PDA-0-102A-00CN-lk.img
EDIT :
yess it worked!!!
thanks for tutorial.
but...after i try......
i dont like chinese rom lol
i revert back to WW....
can you please tell me how to use fastboot mode... i have already make my phone into fastboot mode but i dont know whats next to do.. its just says fastboot mode on my phone with nothing else
great work
my X5 is running on global rom now thanks very much
Hi
in this thread i will show you how to do each of this:
POCO X3 PRO{vayu}
1.TWRP+ROOT
2.RSA DISABLE
3.DIAG MODE
4.EFS RESET
5.IMEI REPAIR
without Any Box.
----------
***********You Will Do it By Your Responsibility and I'm not Responsible for any damage to your Device,Read Thread Carefully and then Do it and try not to mess your device*********
--------
Requirements:
-Iphone 6 Board for its Resistor
-Xiaomi Imei Tool Link
-Qpst Link
-Twrp + EFS Reset Tool Link
-Magisk 23 zip file Link
-Magisk Manager APP Link
-Stock Firmware Link
-Eng Firmware LINK >>>>File Password is : iaasteam.com<<<<<<
--------
I Did All of this Steps and Job Done this Means Its Tested dont Blame me For Any Damage to Your Device
Do it Just if you know What you Do
Not for Newbies
---------------
Some Poco X3 Pro Devices Bootloop After EFS Reset:
it can caused Becuase of Firmware Security or RSA Encryption of Device Imei:
We Have Two Method For this:
1.Flash ENG Rom Then Continue The Steps 1 to 4 and no need root(Because ENG rom have root access already)
2.Do entire Steps on stock Firmware then if it gives error try method 1
But if Not if this methods Work Problem is with the Step 1.RSA DISABLE and you should Check You Resistor
---------------
1.RSA DISABLE
You Should Disable RSA of the Phone To Write Imei on it.
For this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Remove this resistor and Change it with Picture 2 from Iphone 6 Board 50k resistor
for better Performance of work you can Measure its kohm by ohm meter it should be 45 to 50k by ohm meter
replace the resistor in picture one with this
------------
First Time We do entire of Job on stock Firmware if firmware security Prevent us to do our work then we flash the phone with eng firmware,and eng firmware no need root just need flash twrp
-----------
2.TWRP + ROOT
Download Reqirment TWRP + EFS RESET TOOL
Reboot phone in fastboot and connect it to pc
run .bat file and press key 1
twrp will be flashed
Wipe/factory reset Phone by twrp if storage not shown for installing packages reboot agian to twrp
Download Magisk zip and Apk from reqirement
****Go to Backup Section of TWRP>Check EFS Partition>Back it up and Copy it to PC for Avoid Baseband null***** And then Continue the other Steps
Connect Phone to pc
Copy Magisk23.zip to phone storage and install it by twrp
Reboot phone to system
and install Magisk Manager
Now phone Should Be Rooted.
Each time you reboot your phone from Recovery to system,TWRP recovery will be deleted onm your phone
when you see your phone rooted
----------
3.DiagPort & QCN Backup & Modify
Download QPST in reqirement
Xiaomi Imei Tool in reqirement
Install Xiaomi Imei Tool
View attachment 5515295
Connect phone to pc in normal Mode
Enable USB Debugging and Select File Transfer mode on phone
Click Open Diag Port now your diag prot enabled
***** Do not use Xiaomi Imei tool QPST******
Install QPST from Reqirements Section
Run QPST Configuration(you can search in start menu for it Because it dont have shortcut in desktop)
QPST Configuration Detect Your phone in diag mode then
Click on Start Clinets>Software Download>Backup
Backup QCN And Xqcn Both(QCN is enough but I suggest you to backup both of them)
when you backed up Qcn
Open Xiaomi Imei Tool
And run QCN Editor
View attachment 5515301
1.select Qcn file you Backed Up
2.Select Registration Method on 2Sim Like in picture
3.Write Imei 1 and imei 2
4.Click Create Button and Save our Modified QCN.
--------------------
4.EFS Reset And Modified QCN Restore(Imei Repair)
Warning:You should Backed up your EFS By TWRP in STEP 2 and Copied it in PC And Then Come To This Step
Reboot your Phone to Fastboot
-Open TWRP+EFS reset .bat file you downloaded in step 2
-press 1 and wait untill phone reboots to twrp recovery
-in the .Bat File Menu press key 2 when phone already is in twrp menu
-Reboot Phone to system Again Now Efs Reseted and Phone Dont Have IMEI
*******If You Dont Replaced Correct Resistor in Step 1 then your phone should give you NV Data Corrupted Error in this Step or Phone Restarts Each Time********
-When Phone Comes Up Enable Diag port Again and run QPST
Run QPST Configuration(you can search in start menu for it Because it dont have shortcut in desktop)
QPST Configuration Detect Your phone in diag mode then
Click on Start Clinets>Software Download>Restore
Select Modified Qcn that you Created By Xiaomi Imei Tool in Step 3 and Push Start.
Wait Untill Progress Done And Phone Reboots.
Now You Should Have Poco X3 pro Dual Imei Repaired.
If you Get Any Error Just Read Troubleshooting Section
--------------------------------
*****************Troubleshooting****************
1-After EFS Reset Phone Restarts and dont Work Correct
A:it can caused by two problem: 1- firmware security 2-Resistor Change Problem
For Firmware Security:
-Download ENG Firmware From Requirement section and Flash it by fastboot
-then Reboot To Fastboot again Flash Twrp recovery and do not try to root ENG firmware(Because it have Root Access by default)
-In Twrp Reset EFS Again In Step 4
-Reboot to ENG firmware and Enable Diag Port and Write Modified Qcn
-Flash Global Stock Firmware i have linked to requirement no diffrence at all you can flash any version of global firmware
***If Again Problem Not fixed It's your 50k Resistor Changing Problem and you should check it***
2-When I Enable Diag Port QPST Can not find my phone
A:Just Check You Drivers And Device Manager
--------------------------------
*****In Some Websites Says You Need ENG QCN for imei repair,No need of ENG QCN Just Modify Phones Original QCN******
--------------------------------
Files Uploaded To mega.nz and Links Stays Alive forever.
--------------------------------
Push Thanks Button,Like if this Guide fixed your problem
If you have a question, feel free to ask and I will answer as soon as possible
***********You Will Do it By Your Responsibility and I'm not Responsible for any damage to your Device,Read Thread Carefully and then Do it and try not to mess your device*********
I have a question, if I have a Poco X3 Pro with a blank imei and an unknown baseband, I don't have the EFS backup or the box where the imei comes from, changing the resistance and following the step-by-step guide could I recover the imei?
felixpaz1992 said:
I have a question, if I have a Poco X3 Pro with a blank imei and an unknown baseband, I don't have the EFS backup or the box where the imei comes from, changing the resistance and following the step-by-step guide could I recover the imei?
Click to expand...
Click to collapse
if problem not with the hardware
yes of course you can fix it
when you remove resistance and disable rsa
and write its original imei on it.
Any change in the imei ID of the device is illegal in most countries, please respect the law.and Also respect XDA Law about it.
I've reverted the OP and thread title as they were, as well as unlocking it, and will PM all appropriate users.
Thank you.
roirraW edor ehT said:
I've reverted the OP and thread title as they were, as well as unlocking it, and will PM all appropriate users.
Thank you.
Click to expand...
Click to collapse
Thank you, I took the time to write this
Thank you for your positive management
After removing the resistor can it be re-installed?
Jssdje said:
After removing the resistor can it be re-installed?
Click to expand...
Click to collapse
no then rsa enabled again
Non of one of your attachment are available please update the pictures of resistor pic
Thanks
mosirezaei said:
Non of one of your attachment are available please update the pictures of resistor pic
Thanks
Click to expand...
Click to collapse
Hi thank you for report i have uploaded them but now the attachments deleted
wait untill tomorrow i will fix it
dashti.95 said:
Hi thank you for report i have uploaded them but now the attachments deleted
wait untill tomorrow i will fix it
Click to expand...
Click to collapse
Hello
I still waiting for the attachment photos of resistors
if you can send it to my email will be great
[email protected],com
thanks bro
backup efs eng firmware mode .backup was saved fsc,fsg,modemst1 and modemst2. after reset efs baseband unknown. flash backup partition in fastboot mode. still baseband unknown.
problem solved by write qcn.
alak said:
backup efs eng firmware mode .backup was saved fsc,fsg,modemst1 and modemst2. after reset efs baseband unknown. flash backup partition in fastboot mode. still baseband unknown.
problem solved by write qcn.
Click to expand...
Click to collapse
Can you give me the qcn please....
Mail : [email protected]
kallumama said:
Can you give me the qcn please....
Mail : [email protected]
Click to expand...
Click to collapse
tomorrow i will send you
I repair 2nd Imei of Poco X3 pro Vayu from UMT RSA method in eng Rom. I get backup of QCN. it shows imei1 0 imei2 (86*************12) but when I flash global rom. it shows NV data corrupt. I again flash ENG rom. write that backup QCN it shows Original IMEI's but when I flashed Global Rom It shows nv data error again. although Original imei of that Phone. I erase efs from Fastboot that also doesn't help me. what is the problem & how to solve it.
can I flash custom rom for mobile work normally without sim?
or custom rom doesn't help?
if any firmware that solve my problem & phone work normally (without sim) kindly tell me.
saqibsm said:
I repair 2nd Imei of Poco X3 pro Vayu from UMT RSA method in eng Rom. I get backup of QCN. it shows imei1 0 imei2 (86*************12) but when I flash global rom. it shows NV data corrupt. I again flash ENG rom. write that backup QCN it shows Original IMEI's but when I flashed Global Rom It shows nv data error again. although Original imei of that Phone. I erase efs from Fastboot that also doesn't help me. what is the problem & how to solve it.
can I flash custom rom for mobile work normally without sim?
or custom rom doesn't help?
if any firmware that solve my problem & phone work normally (without sim) kindly tell me.
Click to expand...
Click to collapse
1.What Flasher you using to flash data?
2.give me a list of files in your firmware directory please list it for me.
I need to know because:
In qualcomm series of xiaomi phones you have a file named *NON-HLOS*
You should use NON-HLOS file from eng Rom not the original file from global rom.(NON-HLOS file is eng modem file)
give me info i will help you
dashti.95 said:
1.What Flasher you using to flash data?
2.give me a list of files in your firmware directory please list it for me.
I need to know because:
In qualcomm series of xiaomi phones you have a file named *NON-HLOS*
You should use NON-HLOS file from eng Rom not the original file from global rom.(NON-HLOS file is eng modem file)
give me info i will help you
Click to expand...
Click to collapse
I have a doubt in which directory of the ENG Rom I find the NON-HLOS file and if I can back it up, I "install" it in the global Rom, would the QCN written when it was in the ENG Rom work?
dashti.95 said:
1.What Flasher you using to flash data?
2.give me a list of files in your firmware directory please list it for me.
I need to know because:
In qualcomm series of xiaomi phones you have a file named *NON-HLOS*
You should use NON-HLOS file from eng Rom not the original file from global rom.(NON-HLOS file is eng modem file)
give me info i will help you
Click to expand...
Click to collapse
I have followed the guide, I was able to recover the original imei that came in the box, I have changed the 50ohm resistor, when I go back to stock rom I have baseband, I have both imei, but I have no signal, if I want to call a message appears saying "deactivate the airplane mode to call"
felixpaz1992 said:
I have followed the guide, I was able to recover the original imei that came in the box, I have changed the 50ohm resistor, when I go back to stock rom I have baseband, I have both imei, but I have no signal, if I want to call a message appears saying "deactivate the airplane mode to call"
Click to expand...
Click to collapse
Its because of qcn you used its not compatible with your device.
dashti.95 said:
Its because of qcn you used its not compatible with your device.
Click to expand...
Click to collapse
I used the published QCN ENG and edited it with the imei that I found in the original box of the equipment, now both imei appear in the global Rom but I have the ghost plane mode, absolutely everything works except the mobile radio
felixpaz1992 said:
I have followed the guide, I was able to recover the original imei that came in the box, I have changed the 50ohm resistor, when I go back to stock rom I have baseband, I have both imei, but I have no signal, if I want to call a message appears saying "deactivate the airplane mode to call"
Click to expand...
Click to collapse
two questions:
1.Which NON-HLOS you used?Stock or Eng?
2.What type of Qcn you used?.xqcn or .qcn?