Related
** NOTE **
Files you are going to copy/create by this guide, contain your fingerprint. Do not share them with anyone, also keep them at safe place. No one will be responsible other than you!
What exactly this guide will do ?
It will copy FP data from previous working ROM and paste in current ROM where FP enrollment does not work. In short we are bypassing FP enrollment process to eliminate enrollment error.
We are going to backuo FP data, which is stored at /data/system/users.
Important News: Recently we found, FP Enrollment Error in "O" is ROM related and doesn't require O-Modem, it will get solved soon. Use this method until it get solved.
My little Assumption for not requirement of O-modem is: there is no big difference between N and O, N-modem is compatible with O and that's the reason we don't need O-modem for O-ROMs. Source: rovo89 said same for xposed.
I will keep this workaround here for future android updates with large change.
Let's start bypassing enrollment process...
** Requirements **
- Any N-ROM (Stock/Custom doesn't matter)
- Root Manager: SuperSU / Magisk (if ROM is not preRooted)
- ZipMe for creating flashable zip (take APK after installation), Play Store Link : ZipMe
** GUIDE **
- if O-ROM is installed (Take backup, in TWRP)
- Clean install N ROM (and ROOT it.) (Gapps not needed, if you got apk of ZipMe)
- boot it
- go to, > Settings > security > add security of your choice and add 5 FPs (choose 5 spots of your fingers carefully, once you installed them in O-ROM, you will not be able to edit them, only delete is possible)
- open ZipMe, tap "+" (at bottom) then select folder
- go to, > data > system > users [ tap select]
- you will see "users" folder is added to main screen, then tap "create" (bottom bar) (choose your preferred directory and zip name.)
Now you have successfully got backup zip of FPs.
Now, moving to O-ROM.
- Restore O-ROM backup if made otherwise flash ROM, Gapps and other Mods but don't flash FP zip now
- boot ROM
- go to, > Settings > security > add your preferred security lock (dont add FP, it will only give error)
- reboot to recovery
- flash FP zip
- reboot to system
- congratulations, now you can unlock with FP.
** Points to remember **
* Don't share FP zip / keep it private.
* Flashing in recovery is necessary, as we can't replace those files while system is running (TWRP recovery file manager works for copy&paste, but i haven't mentioned because it will be hard for many one)
* If you delete any FP accidentally, you can flash FP zip instantly, Clean flash or Restore of any backup is not needed.
* If you need to change FPs, then only you have to go through all steps.. otherwise for same FPs, you can use same FP zip for any O-ROM / Future updates / Clean Installation. (So, it is one time procedure to get FP zip, then forget everything )
I have no Idea what are you talking about!?!
what does it do?
siddhesh9146 said:
I have no Idea what are you talking about!?!
what does it do?
Click to expand...
Click to collapse
The actual test builds of Oreo have problems with fp enrollment hence his workaround makes you able to use fp with Oreo by copying your registered fp with nougat over to Oreo.
siddhesh9146 said:
I have no Idea what are you talking about!?!
what does it do?
Click to expand...
Click to collapse
Corrected few things and added important news.
Project Treble - https://forum.xda-developers.com/c/project-treble.7259/
The Android 8.0 release includes Project Treble, a major re-architect of the Android OS framework designed to make it easier, faster, and less costly for manufacturers to update devices to a new version of Android. Treble is for all new devices launching with Android 8.0 and beyond.
Project Treble results in GSI ROMs.
There are quite a few GSI ROMs available, but not all of them are suitable for T30 tablet.
I started this thread to summarize my experience with using different GSI ROMs.
The prerequisite for installing GSI ROM is an unlocked Bootloader.
Description of GSI ROM versions installation file names:
<ARCH>_xyZ
<ARCH> can either be arm, a64 (arm32_binder64) or arm64
x can either be a or b
y can either be v, o, g or f
Z can be N or S
b = a/b
a = a-only
g = gapps
o = gapps-go
v = vanilla (no gapps included)
f = floss (free & open source apps instead gapps)
N = no superuser
S = superuser included
The most suitable GSI ROM for T30:
T30 requires A/B ROM instalation file type and Android 10.
Suitable are files with key "arm64-bgN" or "arm64-bgS" in filename. "g" if you want use GAPPS.
b = a/b
g = gapps
N = no superuser
S = superuser included
HavocOS
-> Installation video guide + download all necessary files
-> tested file: Havoc-OS-v3.8-20200821-Official-GApps-arm64-ab.img.xz
-> in TWRP install "RebootFix.zip" to aviid random restarts from attachment.
LeOS - https://forum.xda-developers.com/t/aosp-11-0-2020-11-27-leos-ungoogled-gsi.4195571/
-> installation, see bellow
-> Download tested file: 20201218-RW-bvN.img.xz
Family of TrebleGSI ROMs:
CAOS - Custom AOSP OS
-> installation, see bellow
-> Download, tested file: caos-v300j-201213-arm64-bgN.img.xz
LOSQ - LineageOS 17
-> installation, see bellow
-> Download, tested file: losq-v224-201017-arm64-bgN.img.xz
cRDrom - crDroid 6.11
-> installation, see bellow
-> Download, tested file: crdrom-v224-201019-arm64-bgN.img.xz
qiDroid - BootleggersROM 5.2
-> installation, see bellow
-> Download, tested file: qidroid-v224-201021-arm64-bgN.img.xz
Bless - BlissROM 12.12
-> installation, see bellow
-> Download, tested file: bless-v224-201015-arm64-bgN.img.xz
Nusantara 2.6 - Nusantara ROM
-> installation, see bellow
-> Download1, Download2 , tested file: Nusantara_v2.6-11-arm64-ab-GApps.img.xz
This is Android 11 ROM which fits to our System partition (file size is 2.7GB ONLY)
----------------------------------------------------------------------------------------------------------------------
How to install GSI ROMs on Teclast T30:
a) use this HavocOS Installation video guide, but use specific GSI ROM System file
b) use instructions from 2nd post
GSI ROMs are not perfect, they have bugs, and on the T30 tablet I noticed the following two:
- The battery charging animation does not work (charging works OK) when the tablet is switched off
- watching youtube videos in Chrome browser sometimes ends with a system restart (youtube application and embeded internet browser usually works OK)
I have tried all the above GSI ROMs and I was most satisfied with HavocOS and LOSQ.
I continue to use LOSQ, because it has the fewest errors and supports the NTFS filesystem on the inserted SD card.
If you want to try GSI ROM on your Teclast T30, choose LOSQ / HavocOS as the first choice.
I would be happy if here will start a discussion about GSI ROMs suitable for Teslast T30.
in any problems with PC and tablet communication (with platform tools or Flashtool), install the drivers "MTK_USB_All_v1.0.8.zip" or "platform-tools_r30.0.5-windows.zip" from attachment in the 2nd post
Alternative way to install GSI ROM:
(Prerequisite for installing GSI ROM is an unlocked Bootloader)
a) Unlock Bootloader
- To make the item "For developers" available on the tablet, in Settings / System / Advanced / Tablet information you need to click on the Build number 8 times
- A new "Developer menu" item will now appear in Settings / System / Advanced, turn on the "unblock OEM" item here
- In the task manager on the PC, check that there is an ADB device
- Turn off the tablet
- Hold down the Vol+ and Power buttons together, until the tablet starts
- Then use the Vol+ key to select the second Fastboot item and press the Vol- key to select it
- Connect the tablet to the PC via USB, in the PC to hear the sound of the connection
- Unzip platform-tools_r30.0.4-windows.zip to drive "C:\platform-tools" on your PC
- On your computer, click Start / Run, enter command "cmd", click OK, will appears black command window
- In the command window go to Platform-tools folder by command:
cd c:\platform-tools
- In the command window, enter:
C: platform-tools> fastboot devices
0123456789ABCDEF fastboot
- numbers may vary.
- If all is well, enter the unlock command:
fastboot flashing unlock
- You will be asked on the tablet whether or not you want to unlock the Bootloader by pressing Vol+ confirm it
- As soon as you confirm the action, what you see on the tablet, it will be unlocked
Next, enter the command:
fastboot reboot
- The tablet will restart (ALL your data will be deleted) and the tablet will return to its original state
- tablet will start initially setup
b) Install Hybrid ROM 1.2a
- in TWRP install GSI ROM image file to System partition
- in TWRP install Boot 1.05 image file to Boot partition (unpack ZIP from attachment, will get IMG file)
- restart System
- done
in any problems with PC and tablet communication (with platform tools or Flashtool), install the drivers "MTK_USB_All_v1.0.8.zip" or "platform-tools_r30.0.5-windows.zip" from attachment.
-> New version of HAvocOS from December 31, 2020
Lineage os is not booting and my tab is stuck on teclast logo.Any fix ??
Lightning Killer said:
Lineage os is not booting and my tab is stuck on teclast logo.Any fix ??
Click to expand...
Click to collapse
I assume you didn't follow the installation instructions exactly.
Maybe you forgot to install the Boot image from ROM 1.05 to Boot patition or you didn't unlock Bootloader.
You need to do install Boot 1.05 image in the end of installation process, after installing Lineage GSI on the System partition. Also, Bootloader must be unlocked (it is mentioned in that installation video)
I added necessary img file to attachment. Install it in TWRP to Boot partition. Then Lineage GSI ROM will boot (Bootloader must be unlocked!!!).
(unpack ZIP from attachment, you will get IMG file)
For everyone, I added a new alternative installation guide to the second post.
I have been using it for a long time HavocOS from December 31, 2020
(Havoc-OS-v3.12-20201230-Official-GApps-arm64-ab.img.xz)
It works well. Of course, it has minor flaws like all GSIs.
This is latest version HavocOS on Android 10.
Newer versions of HavocOS 4.1 are based on Android 11.
Unfortunately, the System image with GAPPS is too large to fit in the system partition of our tablet.
The System IMG size limit is 3GB.
GSI HavocOS 4.12 based on Android 11 available
I used this files:
Havoc-OS-v4.1-20210208-arm64-ab-vndklite-Official.img.xz
NikGapps-basic-arm64-11-20210130-signed.zip
It is necessary to incerase System partition size before install, do tgis steps:
- go to TWRP
- Wipe->Advanced Wipe->Select System->Repair or Change File System->Resize File System
- if errors will apperas, restart to TWRP a repeat the previous step again
It may not work first time for whatever reason, you may also try Repair FIle System there in this case, or just try a reboot
rbt07 said:
GSI HavocOS 4.12 based on Android 11 available
I used this files:
Havoc-OS-v4.1-20210208-arm64-ab-vndklite-Official.img.xz
NikGapps-basic-arm64-11-20210130-signed.zip
It is necessary to incerase System partition size before install, do tgis steps:
- go to TWRP
- Wipe->Advanced Wipe->Select System->Repair or Change File System->Resize File System
- if errors will apperas, restart to TWRP a repeat the previous step again
It may not work first time for whatever reason, you may also try Repair FIle System there in this case, or just try a reboot
Click to expand...
Click to collapse
Hi after installing this, I`m in a boot-loop, What can I do?
H1S8V87 said:
Hi after installing this, I`m in a boot-loop, What can I do?
Click to expand...
Click to collapse
Hi, you have to install Boot.img from ROM 1.05 to Boot partition through TWRP.
File is here in 2nd post.
Unpack ZIP anf install IMG file to Boot partition.
rbt07 said:
Hi, you have to install Boot.img from ROM 1.05 to Boot partition through TWP.
File is here in 2nd post.
Unpack ZIP anf install IMG file to Boot partition.
Click to expand...
Click to collapse
Hi, yeah I`ve done this several times. Nothing helps, I`m back to your Hybrid Rom
It worked for me, but I still preferred to go back to the older Havoc.
H1S8V87 said:
Hi after installing this, I`m in a boot-loop, What can I do?
Click to expand...
Click to collapse
For me it works...
I've found a fix for random reboots !!! Just flash this zip file in twrp
GSI HavocOS 4.5 based on Android 11 available
I used this files (click to download):
HavocOS-4.5-official-arm64-ab-vanilla.img
open_gapps-arm64-11.0-pico-20210713.zip
Links:
Havoc 4.5
arm64-ab-vndklite • Havoc-OS
Havoc-OS Downloads
download.havoc-os.com
OpenGAPPS
The Open GApps Project
OpenGApps.org offers information and pre-built packages of The Open GApps Project. The Open GApps Project is an open-source effort to script the automatic generation of up-to-date Google Apps packages. All Android versions and platforms supported.
opengapps.org
How to install:
- as a base system is my Hybrid ROM 1.2a
- Install GSI System image Havoc4. 5
- then increase System partition, do this steps:
a) go to TWRP
b) Wipe->Advanced Wipe->Select System->Repair or Change File System->Resize File System
c) if errors will apperas, restart to TWRP a repeat the previous step again
If incerasing fails, reboot to TWRP recovery and try again, now it will works now
- install GAPPS.
- reboot System
Add nusantra project gsi to the list !!! It is much more smoother than havoc and lineage os Here's the link for 2.5 (based on android 11 )
[email protected] - Browse /Nusantara-11 at SourceForge.net
sourceforge.net
+ It comes with gapps and can easily be flashed without having to resize the system partition
deleted
Lightning Killer said:
I've found a fix for random reboots !!! Just flash this zip file in twrp
Click to expand...
Click to collapse
Hi, thanks, it reallly work for HavocOS 3.8 GSI ROM.
rbt07 said:
Added to 1st post, thanks for info.
Do you use it? Write somthing about this ROM please.
Click to expand...
Click to collapse
It's the best gsi rom for teclast t30 I have used till date !!! It is very smooth and responsive. There are some customisation settings which crash when using in landscape mode but they work just fine in potrait mode.else this rom works like a charm for me.
Another gsi for teclast t30 that I would recommend is cr droid gsi based on android 11 . Here's the link -
TrebleGSI - Browse /crDRom11/2021.05.21 at SourceForge.net
sourceforge.net
Lightning Killer said:
It's the best gsi rom for teclast t30 I have used till date !!! It is very smooth and responsive. There are some customisation settings which crash when using in landscape mode but they work just fine in potrait mode.else this rom works like a charm for me.
Click to expand...
Click to collapse
I will try soon, thanks.
What is this?
Pixel Experience is an AOSP based ROM, with Google apps included and all Pixel goodies (launcher, wallpapers, icons, fonts, bootanimation)
Our mission is to offer the maximum possible stability and security, along with essential and useful features for the proper functioning of the device
(NOTE YOU CANNOT UPDATE FROM PE 11 WITHOUT SEVERE BUGS BACKUP YOUR DATA WITH NANDROID OR ANOTHER APP AND RESTORE IN 12)
Based on Android 12.0
Disclaimer:- This will void warranty.
You will need to unlock bootloader.
*All your data will be lost*
Read all the steps correctly
BUGS:-
mtp (aka transferring files from phone to pc or vice versa with a cable) will not work with adb (it will freeze phone ) to use mtp disable usb debugging in developer options then once you disable usb debugging click usb settings and choose storage
headphone jack does not work (enable use alternative way to detect headsets in phh settings)
audio volume might be low on some devices install the dsp audio module and
DO NOT let the phone die of battery you will not be able to boot and it will be hard to get back into the system (workaround- in magisk install acca https://github.com/Magisk-Modules-Repo/acc and install this apk after installing https://github.com/MatteCarra/AccA then set profile to default (this will shut down the phone at 5% hence removing the risk of your phone not booting after hitting 0%
You tell me
Links
Rom- Download
Stock Samsung kernel source.
Install-
1.Use twrp 3.5.1 (others did not work for me good luck in testing)
2 Unpack the "xz" archive and put the .img file onto the sd card or internal (if you dont have a sd card do step 3 then transfer the img file to your phone)
3. In TWRP head to factory reset format type yes and hit enter
4. Flash the img file (as system obviously)
5. flash eureka oneui kernel (DONT FLASH THE NON ONEUI ONE ONLY FLASH ONEUI EUREKA KERNEL)
6. flash magisk (it is optional but for best performance you should) (use 21.0 for android 12)
Credits-https://github.com/phhusson/
ponces - Overview
Husband of Rita. Father of Luke. Fan of Android and Linux. There is no place like /home 🤓 - ponces
github.com
Pixel Experience Team, phhusson, AndyYan and eremitein -
Zainullah Boot fix (if you cant boot)
install oneui boot into oneui change date to 3 months from now
check for updates
boot into download mode
flash twrp and vbmeta
boot into twrp
do format data
flash multidisabler
flash rom
flash kernel as boot
do factory reset
reboot
if it boots you into fastboot shutdown flash twrp only and try another factory reset and reboot (In twrp)
(Android 12 )
No gapps needed (after installing update all apps in play store including play store itself)
Camera works but use gcam go mod by greatness https://www.celsoazevedo.com/files/android/google-camera/dev-greatness/f/dl9/
if there is any working gcam mod link it so i can test it
gcam go is way way better than the stock camera with hdr night mode portrait and soon filters
(ultra wide and other cameras do not work for now)
Increase performance without any battery impact or (by feravolt and gloeysik)
Step 1
- Install FDE AI Magisk Module to make it a system app, thus it will work better and removes all kernel locks from OEMs (I'm looking at you, Samsung) https://github.com/feravolt/FDE.AI-docs/releases/download/12.4.1m/FDE.AI-as-system-app.MAGISK.zip
- Update FDE AI to the latest version by downloading the latest APK here, since the fde ai magisk module will only install fde ai 12.4.1, not the latest version: https://github.com/feravolt/FDE.AI-docs/releases
- Move to the bottom of the screen and select AI Chat, then type /advancedai (no space, no uppercase letters). This will going to make the AI more effective, without you having to do anything.
- Go to the settings tab and use the AUTO settings for FDE AI.
Optimized and adjusted Google Play services. Contribute to gloeyisk/universal-gms-doze development by creating an account on GitHub.
github.com
install cloudflaredns4magisk
[MODULE] CloudflareDNS4Magisk
install adaway (optional if you want ads or not) , allow superuser for it download this https://energized.pro/bluGo/formats/filter in adaway click he button in the middle click add click file and add the file then go back to the main menu and click the reload button now https://adaway.org/
Blog
Pixel Experience
Donate
jhenrique09
phhusson
AndyYan
eremitein
ponces
supports A307gt?
yes this is a gsi it works on all a30 and a30s but there might be bugs try on your own risk there is no issues on my a307 -fn
There is a problem in the download link my IDM did not work here!
Please Upload a new link
#Beta_tester
it works try the new link
Is the file name (Pixel experience 11 stable)?
Rafyhasan69 said:
Is the file name (Pixel experience 11 stable)?
Click to expand...
Click to collapse
yes
Rafyhasan69 said:
Is the file name (Pixel experience 11 stable)?
Click to expand...
Click to collapse
tell me how the install goes and if there are any bugs
Zainullahk1234 said:
tell me how the install goes and if there are any bugs
Click to expand...
Click to collapse
PixelExperience_a30-11.0-20210913-0041-UNOFFICIAL.zip Did not flash via TWRP IT Gets Error
Rafyhasan69 said:
PixelExperience_a30-11.0-20210913-0041-UNOFFICIAL.zip Did not flash via TWRP IT Gets Error
Click to expand...
Click to collapse
E3004: This Package is for device: a30,a30dd; this device is a30s.
Updater process ended with error: 1.
how to fix the screen
Rafyhasan69 said:
how to fix the screen
Click to expand...
Click to collapse
yes Go to settings → Phh Treble Settings → Misc features →set Rounded corners to 30
Rafyhasan69 said:
how to fix the screen
Click to expand...
Click to collapse
did it work?
yes it works
hi, does nfc work ?
makadang said:
hi, does nfc work ?
Click to expand...
Click to collapse
yes
Zainullahk1234 said:
What is this?
Pixel Experience is an AOSP based ROM, with Google apps included and all Pixel goodies (launcher, wallpapers, icons, fonts, bootanimation)
Our mission is to offer the maximum possible stability and security, along with essential and useful features for the proper functioning of the device
Based on Android 11.0
Disclaimer:- This will void warranty.
You will need to unlock bootloader.
*All your data will be lost*
Read all the steps correctly
BUGS:- Fingerprint does not work (Can be fixed but is very complex and will not be included in tutorial)
fake corners that cut the screen (fix included in thread)
You tell me
Links
Rom- https://github.com/zainullahk/Pixel-expierence-For-a30-and-a30s-
Stock Samsung kernel source.
Install-
1.Need TWRP 3.4.0 or higher!
2. Unpack the "xz" archive and put the .img firmware file into your storage or sd card
3. Go to TWRP and do wipe data-yes
4. Make Wipe data, cache, cache-Dalvik in advanced wipe
5. Flash our .img file which we threw on the Usb/sdcard/storage
6. If you want flash magisk flash it
7. how to fix the rounded corners issue Go to settings → Phh Treble Settings → Misc features →set Rounded corners to 30
Credits-https://github.com/phhusson/treble_experimentations/releases
(Android 11 )
No gapps needed (after installing update all apps in play store including play store itself)
Camera works but use gcam go mod by greatness https://www.celsoazevedo.com/files/android/google-camera/dev-greatness/f/dl9/
if there is any working gcam mod link it so i can test it
gcam go is way way better with hdr night mode portrait and soon filters
(ultra wide and other cameras do not work)
(if face unlock is not working download the pixel feature drop magisk module and install it this fixed face unlock for me and also added more pixel only features
GitHub - ayush5harma/PixelFeatureDrops: Magisk Module for Pixel Feature Drops that adds the system files for the same and spoof using the latest device fingerprint from Google Pixel .
Magisk Module for Pixel Feature Drops that adds the system files for the same and spoof using the latest device fingerprint from Google Pixel . - GitHub - ayush5harma/PixelFeatureDrops: Magisk Modu...
github.com
(images)
View attachment 5447277View attachment 5447279View attachment 5447281View attachment 5447275
Click to expand...
Click to collapse
new bug fix update
nfc did not work on some devices this is fixed
face unlock fixed
minor performance improvements
Rafyhasan69 said:
yes it works
Click to expand...
Click to collapse
flash this in twrp https://forum.xda-developers.com/t/...flagship-stereo-sound-system-for-a30.4245743/ it will fix sound
Zainullahk1234, good job man. The best firmware for today. Thanks for it.
Works great! Thanks
edit: headphones true jack not working?!
S908B & S908E system-rw Dr.Ketan ROM
Supported device : S918B & S908E/N for Full ROM, All rootable variants for Magisk Module
We do support usually 2-3 years since device launched, but yet no guarantee, We may drop support for any device / any variant/s anytime without any prior notice.
ROM Features
ROM Features varies with version of ROM. For more details, read changelog post. Link available in post #3 for changelog of all versions.
Must read changelog for a version you are going to install, it will have latest information about features, changes, known bug list/fix and Installation guide of respective version.
There are two types of ROM available since OneUI 5.0
1.Full system-rw ROM : Full ROM includes super.img with system-rw capabilities + stock enforcing kernel + ROM Control & Modification
Supported device : S908B & S908E
2.Magisk ROM Module and here explained in details how it is different from full ROM
Supported device : All S22 variants
Credit and Thanks :
@Chainfire - Respected elite developer for supersu and his unbelievable contribution to XDA/Android community. @wanam - Respected elite developer for his awesome contribution and references to his works.
@topjohnwu for Magisk
@xperiacle the amazing developer for reference to his work and tools. @amarullz for aroma installer. @gharrington for 3minit battery and QuickLaunch.
ROM Control source and all credit and thanks goes to @daxgirl and @Wuby986 for their open source project for RomControl.
@AbrahamGC for some ideas samsungvn htcmania & 4PDA for tips and some stock apks.
AbrahamGC and Anan1211 for Secure folder and s-health A12 ianmacd for TWRP @afaneh92 for TWRP, system/vendor rw scripts and modules. @Arteush for bluetooth fix (losing BT pair on reboot) on Android Q, aka_vkl for Dolby digital, kdrag0n for SafetyNet fix @Winb33 for custom font pack. HuskyDG for Bootloop Protector magisk module. MrWeahere for CRB Kitchen
XDA devDB InformationS908 I Dr.Ketan ROM , ROM for the Samsung Galaxy S22 Ultra
Contributors
Dr.Ketan
ROM OS Version: Android 12
ROM Kernel: Stock (pre-rooted). Source code (samsung) here
ROM Firmware Required: Stock Samsung specified version
Version Information
Status: Stable
Created 2022-03-12
Installation, Important Infos & Download
Installation : State of the art Installation procedure.
Detailed installation guide separately available in download area along with ROM files for Full ROM and for magisk module read changelog post.
WARNING
Before you root your device you must be aware that
This will void warranty.
As of now you will lose Samsung Pay and Samsung Pass forever if you root once, even unrooting won't help.
There are many features stop working when you unlock bootloader other than S pay/Pass like Samsung Health, Secure Folder, Galaxy Watch pairing issue, Issue connecting old gear watch (S3 or earlier), Google Pay etc but ROM is patched for all these mentioned features. Still you may trouble using some bank apps and these may fixed by adding these apps to Magisk Hide
There may be some knox features there which you may not able to use but I can't list those as I never used. Just Google It
Patched featurs are working today when writing this, No idea if it may stop working next moment/tomorrow or later
Also to note, once you root, you can't go back to "pre-rooted" state completely. It is one way!
OTA won't work once you root device.
ROOT with caution.
You can unroot & Relock bootloader after flashing stock firmware, but still your warranty flag remain 0x1 and most of countries it still voids warranty. Also after unrooting & relocking bootloader, some knox features never work again.
ROM Tool permission : Files & media - To save and read files, Calendar - Tool needs some time monitoring to avoid using RT immediately after reboot. Special access for accessibility service - Since Android 12 it requires for QS panel custom Toggl e.g. Reboot to recovery
Download : https://drketanrom.com/
ChangeLog for Magisk Module ROM
OneUI 4.0
Spoiler: ChangeLog OneUI 4.1
ChangeLog OneUI 4.1
- S01 - 12.03.2022
- S02 - 14.03.2022
- S03 - 19.03.2022 & S03.1 - 30.03.2022
- S04 - 06.04.2022
- S05 - 27.04.2022
- S06 - 27.05.2022
- S07 - 05.06.2022
- S08 - 18.06.2022
- S09 - 08.07.2022
- S10 - 05.08.2022
- S11 - 15.10.2022
OneUI 5.0
- T01 - 26.10.2022
- T02 - 19.11.2022
- T03 - 14.12.2022
- T04 - 15.01.2023
OneUI 5.1
- T05 - 17.02.2023
- T06 - 11.03.2023
- T07 - 14.04.2023
- T08 - 15.05.2023
- T09 - 20.06.2023
ChangeLog for Full System-RW ROM
OneUI 5.0
- T01 - 07.11.2022
- T02 - 20.11.2022
- T03 - 14.12.2022
- T04 - 17.01.2023
OneUI 5.1
- T05 - 17.02.2023
- T06 - 11.03.2023
- T07 - 11.04.2023
- T08 - 12.05.2023
- T09 - 21.06.2023
How to Root (currently non rooted device) with or without TWRP
Spoiler: Root existing non rooted device
Root with or Without TWRP
1.Root without TWRP :
Unlock Bootloader
You needs to download stock firmware (You can get stock firmware with Frija) and extract AP*.tar.md5 file and patch with magisk. Flash patched file with AP tab of Odin PS : In case root files without TWRP available in download area for your variant, you can use that for AP slot instead of Patching AP
put device in download mode and connect to PC and flash above files
Reboot to recovery and select to format data
Reboot to system → You will see Magisk stub in drawer → Update it. (In case stub not there, Donload magisk app from Download area and intall manually) → Open Magisk - It will ask to complete additionl setup, Let it do. → Reboot device. You are now ready to Intall Dr.Ketan ROM module. Move to next step.
2.Root with TWRP
Unlock Bootloader
Download TWRP, Patched vbmeta and Kernel and system-rw script zip from TWRP thread (Link below)
Select TWRP tar file with AP slot and Patched vbmeta for USERDATA slot of Odin PS : In case root files with TWRP available in download area for your variant, you can use that for AP slot. It contains both TWRP+patched vbmeta
Put device in download mode and connect to PC and flash above files
When Flashing completes, disconnect device and starightway reboot to TWRP
Run multidisabler from TWRP → Advanced → Terminal → and type : multidisabler (it may take few minutes, keep patience)
Wipe Data (Full wipe, that you needs to type YES to continue)
Reboot TWRP and now connect to PC and copy Custom kernel and flash from TWRP as zip
get Latest magisk apk and flash from TWRP
If you want to make system-rw, Get afaneh92_lp_rw_tool_v*.zip from TWRP thread and flash
Reboot device to system Update Magisk from stub if availble OR Install Magisk apk
Now ready to install Dr.Ketan Module, Follow XDA ROM Changelog post to install ROM Module
Thanks & Credit to Afaneh92 for TWRP & Kernel, below are link for OP Exynos and SnapDragon
PS : For detailed instructions about Magisk installation (root) read here. In case still you have question, move to Question forum of S22 section and ask for help. This thread is development thread and any questions related to how to root will be ignored.
How to Update Firmware and Keep root/twrp intact without losing data
PS : We highly recommend to make data backup before trying this as something went wrong and you may lose data.
Spoiler: Update Firmwre with Keeping Root/TWRP/data intact
Read below methods depending on you have root with or without TWRP
1.Rooted S908B/E/N/0 without TWRP
Unlock bootloader
You needs to download stock firmware you want to update (You can get stock firmware with Frija) and extract AP*.tar.md5 file and patch with magisk. Select Patched AP file for AP slot and BL*.tar.md5,CP_tar.md5,Home_CSC*tar.md5 for BL,CP and CSC slot accordingly. (PS : In case root files without TWRP available in download area for your variant, you can use that for AP slot instead of Patching AP, Importnt : Use Home_CSC*tar.md5 if you want to keep data. Selecting CSC*.tar.md5 will Wipe data autometiclly.)
Reboot device → You are now ready to Intall Dr.Ketan ROM module. Move to next step.
2.Rooted S908B/E/N/0 with TWRP
Download latest firmware as per pre-requisite
Disable Auto Reboot option in Odin
Select appropriate slot in Odin for BL,AP,CP and CSC (Using HOME_CSC will keep data, while using CSC* will format data) from stock firmware
Select TWRP file for USEDATA slot . File must include patched vbmeta file. If TWRP doesn't have patched vbmeta included, you have to make one yourself. To make TWRP+Patched vbmeta : Download both the files from TWRP thread and extract it to get recovery.img and vbmet.img. On your PC, select these two .img files and Rt click → select 7zip → Add to archieve → select archieve format "tar" → Select OK and this will create a tar file that have TWRP+Patched vbmeta. Use newly created tar file for Userdat slot of Odin. PS : Incase download area have Rootfiles with TWRP for your device then it contains everything TWRP+patched vbmeta + Kernel, extract zip to get all required files
When Flashing completes, disconnect device and starightway reboot to TWRP. Importnt : At this stage you should be quick to reboot to TWRP, If you flais and device tries to boot to system, you may have to wipe data.
Run multidisabler from TWRP → Advanced → Terminal → and type : multidisabler (it may take few minutes, keep patience)
Wipe Data (If you are already using Afaneh92's TWRP and used multidisabler + Format data, you can select to Factory Reset too (This will preserve media file) OR you can skip wipe option at all in case you want dirty Install.)
Reboot to TWRP In case you have wiped data.
Copy Kernel & Magisk apk/zip to device (Alternatively use USB storage)
Install kernel (Flash Kernel zip from TWRP)
Flash Magisk
If you want to make system-rw, Get afaneh92_lp_rw_tool_v*.zip from TWRP thread and flash
If you don't have magisk app in drawer (in case of clean install), Install manually.
Open Magisk app and complete setup if it asked for
PS : If you are on any other TWRP or Stock recovery, you must FORMAT DATA (That requires to type 'Yes' to confrm wipe)
Now ready to install Dr.Ketan Module, Follow XDA ROM Changelog post to install ROM Module
Thanks & Credit to Afaneh92 for TWRP & Kernel, below are link for OP Exynos and SnapDragon
PS : For detailed instructions about Magisk installation (root) read here. In case still you have question, move to Question forum of S22 section and ask for help. This thread is development thread and any questions related to how to root will be ignored.
Help & Support
We do support only ROM related queries here over XDA thread only, we do not have/encourage any private support over telegram or other media to support ROM related queries.
We do not answer any ROM related question over private chat.
If your queries doesn't have enough information, it will be ignored.
We recommend everyone to read OP,Changelog and Installation guide before you install ROM. If answer to your queries already there in OP, Changelog post or in Installation guide, it will be ignored
Any queries not reated to XDA ROM (e.g. TweaksPro) then you must seek help from developer over mail/privately. Here we discuss only XDA ROM related issue.
For reporting issue/bugs you must provide enough info as said below under "How to report bug/issue"
How to report bugs/Issue?
To report issue, you needs to provide following informations, else it will be ignored. Also if your query is already mentioned on OP/ChangeLogg post, it will be ignored.
1.ROM build number.
2.Dirty/Clean Install. - If you have dirty installed, Then first clean install and report if issue persists.
3.Bug/Issue appears right after installing or later?
4.How to reproduce error.
5.Is there any same reports there on thread on your searching?
6.Is there any mention about same bug on OP or changeLog post?
7.Logs - Attach logs here/Upload to other places where it can be downloaded without registration and doesn't have ad (we recommend dropbox/Gdrive) and post link.
Click to expand...
Click to collapse
Finally! After all the teasers and trailers ... We are getting into serious business !
THANK YOU
All the best and cheers Dr. !
ChangeLog S01
Based on S908EXXU1AVBF Android12 March 2022 security patch OneUI 4.1
ROM Tool on essential fix auto setup zygisk including SafetyNet fix (no needs to change any option manually)
Important Instructions for setting up ROM (NEW)
Prerequisite :
Must have installed firmware S908EXXU1AVBF S22 Ultra
Rooted device with Magisk (Zygisk) Intallled (Follow steps belo in case you have non rooted device)
How to Root device
Unlock bootloader
Download Root_files*.zip (available in download area) - Extract and Flash Root_Files_*.tar.md5 with Odin for AP tab
Reboot to recovery and select to format data (Factory reset option on stock recovery)
Reboot device → You will see Magisk stub in drawer → Update it. (In case stuf not there, Donload magisk app from Donload area and intall manually) → Open Magisk - It will ask to complete additionl setup, Let it do. → Reboot device. You are now ready to Intall Dr.Ketan ROM module. Move to next step.
How to Install Dr.Ketn ROM Module
Download DrKetan_ROM_S*_module.zip and copy to device, We recommend to check MD5 to rule out faulty download
Uninstall any other magisk module you have installed
Open Magisk app → Click on Module → Select Install from storage → Select Module file you have copied to device → Complete Intallation and reboot device
Setting up device first time after Module installation
Open ROM Tool, Apply essential fix and Reboot,
After reboot you can check SafetyNet and should be passed. You can use this app from playstore or This from Github to check SafetyNet
Now you can further setup ROM a per your liking. Also MagikHide is Configure Denylist now and available under Magisk Settings.
Since A12 Stable Magisk not working and new Magisk doesn't have buil-in Module repo, You can get standalone module manager from here For more details and queries about new magisk ref this
PS : Plz don't install any other mods for SafetyNet, All queries related to Magisk/SafetyNet will be ignored if already explained above
TweaksPro version requires 4.1.0 or up
ROM Features (XDA Version)
- Ad Free QS Panel Toggle
- Reboot to recovery QS Panel Toggle
- Native call recorder (Manual) While you are on call - click 3 dot - Record (Should work without CSC restriction)
- Auto Call recorder without CSC restriction (ROM Tool - Mods & Fix)
- High Volume warning disabled
- Pre fixed Titanium freezing while restoring apps
- Probable fix for Titanium Backup schedule
- Internet browser Secret mode
- S Health patch for using with rooted device.
- ROM Tool with following Options
AdFree mode Enable/Disable
Single click install/uninstall custom fonts (on the fly)
YouTube Vanced Installer (No xposed requires)
NonRoot - Requires MicroG to login
Root - Truely alternate to Youtube, Can login to youtube without MicroG (disable Play store update)
You have to click on NonRoot/Root depending on your choice, then you needs to click "Install" tab and latest version of Youtube vanced will get installed.
StatusBar Icons
Show/Hide stock battery
Show/Hide 3minit battery
show/hide stock clock
show/hide 3minit clock
ROM Control - See below
Mods & Fix
Auto Call Record
Titanium backup FC fix
Google Pay Fix
Added camera fix (Certain users reported camera failed issue. This is reported on stock too, here is someworkaroung meanwhile samsung fix it)
SafetyNet Fix
Samsung Health & Private share fix
Update & Fix
- ROM Control (systemUI preferences)
Battery Bar with thickness and color option
Virtual key on statusbar (Lt/Cinter/Rt)
Network meter with Toggle (Lt/Rt/Quick Panel/None) with color option
PS : There may be few more options in ROM control but won't work if those are not mentioned here.
Known Bug/Tips/Fix
3 minit users can use 3minit battery paid version for free. Check this (Thanks to gharrington )
Tips on TWRP and App Backup/Restore Read Here
Download : DrKetanROM.com
PS : This is a fully customized ROM and for end users only, ROM or any part of ROM not allowed to redistribute,modify or to use as base to prepare new ROM.
STATUS : Online
Haleluja, its here!! Great amazing work! OMG I'm so excited! Let's go!!
Thanks alot !!! Finally I can unpack my S22 Ultra ^^ and use it as real Phone
Proud to be the first worldwide to have a Custom ROM, FULL ROOT, Adblock etc on a S22 Ultra Exynos
Community LOVE for you!! ♥♥♥♥♥
EDIT: HERE IS THE GUIDE TO USE FOR EXYNOS (still testing)
Ok, so basically find and download the firmware (S908BXXU1AVC6 for EU - or ask me for the File..) to the phone eather with the Phone itself or trought USB-Cable, install magisk.apk from here, unpack the zip file from Firmware and patch the ap file via magisk, get the files to the pc and use odin to flash the patched Firmware.
of course unlock bootloader before and go to download mode.
Here is how to do that:
Guide to root Galaxy S22 Ultra (B/E/N/0), unlock bootloader and flash official firmware (noob friendly)
Your warranty is now void. If you root your device, Your KNOX status will be tripped. You can still pass the safety net after you root if you follow the instructions. Sorry for USA models, you can't root unless you can unlock your bootloader You...
forum.xda-developers.com
or
https://www.droidwin.com/how-to-unlock-bootloader-on-samsung-galaxy-s22-s22-plus-s22-ultra/
Then follow the other steps from Dr. Ketan
S01 Dr.Ketan Magisk ROM is Online now
Must read changelog above for Installation guide and other Info
Thank you for Support & Trust on this ROM.
no rom, only module
Yaiks. Hopefully it will be available for B variant
iampatricktan said:
Yaiks. Hopefully it will be available for B variant
Click to expand...
Click to collapse
You can try on exynos (only module, no root files). If it doesn't work then maximum you needs is to factory reset.
In that case I may consider to make separate rom
dr.ketan said:
You can try on exynos (only module, no root files). If it doesn't work then maximum you needs is to factory reset.
In that case I may consider to make separate rom
Click to expand...
Click to collapse
I think its much better to make separate only for Exnos variant? So that files for SD will not be included, correct me if I'm wrong about that. Also been using your ROM since my Note 9.
dr.ketan said:
S01 Dr.Ketan Magisk ROM is Online now
Must read changelog above for Installation guide and other Info
Thank you for Support & Trust on this ROM.
.
Click to expand...
Click to collapse
Huge thx my bro
ok, so great news, it works at least for exynos as well!
Safetynet also works!
Problems so far:
Can't change my keyboard - UI restarts
com.android.phone closes down
and it says system is unstable - please do a factory restore - on boot up.
But all in all it seems to work, with root etc.
Thx Dr My bro. Hopefully we can have the Exynos version seperatly if possible and not too much of your time consuming.
beautyangel said:
Thx Dr My bro. Hopefully we can have the Exynos version seperatly if possible and not too much of your time consuming.
Click to expand...
Click to collapse
||||| said:
ok, so great news, it works at least for exynos as well!
Safetynet also works!
Problems so far:
Can't change my keyboard - UI restarts
com.android.phone closes down
and it says system is unstable - please do a factory restore - on boot up.
But all in all it seems to work, with root etc.
Click to expand...
Click to collapse
Will do it later today
Any of you free just inbox me
For S908B EXYNOS Users
I have added Bootlogo error text removal file in Download area. Instructions packed inside.
PS : DON'T USE ON SNAPDRAGON device
.
A thousand thank yous @dr.ketan and to @||||| for your Exynos work
Just need delivery of my S22 from Sammy now
dr.ketan said:
For S908B EXYNOS Users
I have added Bootlogo error text removal file in Download area. Instructions packed inside.
PS : DON'T USE ON SNAPDRAGON device
Huge Huge thx Dr my Bro and @||||| for all Awesome job.
Click to expand...
Click to collapse
Official AOSP for Huawei (prague, mediapad, warsaw, rhone) - LeaOS-PHH
LeaOS is a project which based on AOSP with phhusson's Treble GSI patches. I have added my personnals patches for Huawei devices : Encryption, Signal Strengh, Speed Boot, Assisted GPS, NFC, Media App, Default Sound, MediaScanner fixes etc..) and some eremitein patch
Changelog :
LeaOS-PHH Jun 2022 version
Fix MiraCast / Wifi-Display crash
Pass SafetyNet (Basic + CTS) without Pixel 5 Spoof
Add dynamic root
Add option in TrebleApp to collect adb log and create txt file in sdcard
Add support of 8.0.0.416 with this patch (8-Huawei-PRA-FixPreav-A-v1.0-signed.zip)
LeaOS-PHH May 2022 version
Initial build from PHH AOSP A11-r48 (October)
Add support of data encryption
Add NFC Quick Setting (NFC by default are disabled)
Add Android SPL (Nov, Dec 2021, Jan, Feb, March 2022)
Add Default sound (ringtones, alarm and notification)
Add Huawei bootanimation (no sound)
Add support of multi-user
Pass SafetyNet (enable in TrebleApps setting)
Add several new functions in TrebleApps (dumlog, restartui, run on boot) by eremitein
Fix Signal strenght indicator (and icon)
Fix Media App permission
Fix MediaScanner crash
Fix Slow-Boot
Pre-requisite :
You must have TWRP installed, use this one (make sure to have the unofficial Android 11 one ! ). To install follow this guide "How to unlock Huawei P8 ligt 2017 (en).pdf" or french version "How to unlock Huawei P8 ligt 2017 (fr).pdf"
Installation (crypt or uncrypt)
Download file : "LeaOS-PHH-20220616-iceows-pra.7z" and extract img file
boot to TWRP
Wipe internal storage, format data
flash this file 1-Huawei-DataPrep-DeCrypt-A-v1.0-signed.zip to disable storage encryption or this file 1-Huawei-DataPrep-Crypt-A-v1.0-signed.zip to enable it. This zip change fstab file, wipe data partition and recreate subfolder /data/user*, /data/system* and /data/vendor*)
Wipe system, cache, dalvik/art cache
reboot to bootloader
run: fastboot flash system <drag system.img here>
(optional) flash Siberia kernel : fastboot flash kernel <drag Siberia.img here>
reboot to TWRP
resize system
flash this file 2-Huawei-system-UnCrypt-v1.3-signed.zip to not-allow data encryption or this file 2-Huawei-system-Crypt-v1.3-signed.zip to allow it
(optional only PRA) flash AGPS patch : 7-AGPS-FIX-AltairVendor-v3.6-signed.zip
reboot to System and set up the phone with aosp first start assistant. You can also add most user
(optional) reboot to TWRP to install now Google Apps : Google Apps Lite ([RECOVERY]LiteGapps_arm64_11.0_v2.6_official.zip)
Enjoy !!!
Update (crypt or uncrypt)
Download file : "LeaOS-PHH-20220616-iceows-pra.7z" and extract img file
boot to TWRP
Wipe system, cache, dalvik/art cache
reboot to bootloader
run: fastboot flash system <drag system.img here>
(optional) flash Siberia kernel : fastboot flash kernel <drag Siberia.img here>
reboot to TWRP
resize system
flash this file 2-Huawei-system-UnCrypt-v1.3-signed.zip to not-allow data encryption or this file 2-Huawei-system-Crypt-v1.3-signed.zip to allow it
(optional) flash AGPS patch, Google Apps :
1 - Google Apps lite (LiteGapps_Core_arm64_11.0_v2.5_official.zip)
2 - Enable AGPS (2 - AGPS-FIX-AltairVendor-v3.3-signed.zip)
reboot to System
Enjoy !!!
Source Code:
https://github.com/Iceows
ROM OS Version: Android 11
ROM Kernel: Linux 4.4.x : stock 4.4.26 or Siberia_4.4.302-1.1.zip (this kernel not pass safetynet)
ROM Firmware Required: EMUI 8
Based On: PHH AOSP
Credits:
PHH
eremitein
rakinthegreat
And all the others who tested my patches and helped me improve this ROM
Support Group
reserved
Does syberia kernel work on any hi6250 device? Or it is only for pra?
Btw thanks for the rom...hope volte will work on this
I tried on my p10 lite using the uncrypt and it booted fine but I couldn't install or update apps. I tried to clear storage on play store and download manager it didn't work. When I went back to leaOS I tried this 1.3 version of the uncrypt and the same thing happened so it might be from that.
I tried both LiteGapps and OpenGapps.
Thank you for your dedication! Can this ROM use magisk24? If not, is there any Android 10 or higher ROM that can use magisk24 for hi6250?
Can I make calls normally after flashing the Siberia kernel? I want to use magisk24 on this ROM, how can I do it?
UselessShane said:
Does syberia kernel work on any hi6250 device? Or it is only for pra?
Btw thanks for the rom...hope volte will work on this
Click to expand...
Click to collapse
Siberia work on :
PRA-LX1/PRA-L31
RNE-L03
BLN-LX1
AGS-L03
[KERNEL][EMUI 8][P8 lite 2017] Siberia kernel
SIBERIA KERNEL Disclaimer: Use this kernel at your own risk. Flashing it may brick your device. I'm not responsible for any software/hardware and any kind of damages/losses. NOTE : Use only on EMUI8 base(stock or custom) kernel works on all...
forum.xda-developers.com
zuldorak said:
I tried on my p10 lite using the uncrypt and it booted fine but I couldn't install or update apps. I tried to clear storage on play store and download manager it didn't work. When I went back to leaOS I tried this 1.3 version of the uncrypt and the same thing happened so it might be from that.
I tried both LiteGapps and OpenGapps.
Click to expand...
Click to collapse
Use Only LiteGapps.
To install : GO to TWRP, flash 1.3 version of disk-uncrypt and after flash LiteGApps recovery version. Reboot
ZXGUi said:
Thank you for your dedication! Can this ROM use magisk24? If not, is there any Android 10 or higher ROM that can use magisk24 for hi6250?
Click to expand...
Click to collapse
I haven't tested on my AOSP ROM. Magisk 24 runs on the Lineage version of LeaOS. Use the canary version
ZXGUi said:
Can I make calls normally after flashing the Siberia kernel? I want to use magisk24 on this ROM, how can I do it?
Click to expand...
Click to collapse
Yes on version support by Siberia
If you have dual-sim phone, flash correct EMUI update for dual-sim
AltairFR said:
Siberia work on :
PRA-LX1/PRA-L31
RNE-L03
BLN-LX1
AGS-L03
Click to expand...
Click to collapse
also was-lx1a (my p10 lite 4gb ram)
AltairFR said:
Use Only LiteGapps.
To install : GO to TWRP, flash 1.3 version of disk-uncrypt and after flash LiteGApps recovery version. Reboot
Click to expand...
Click to collapse
I followed every step in the guide and it didn't work but I got it working by installing your leaOS and then this rom again.
Steps:
Stock Rom -> LeaOS-PHH (AOSP) - It didn't work can't install or update apps from store
Stock Rom -> LeaOS-PHH (AOSP) -> LeaOS -> LeaOS-PHH (AOSP) - Everything works
I installed magisk and securize phh to pass safetynet.
Everything is working now, great work!
zuldorak said:
I followed every step in the guide and it didn't work but I got it working by installing your leaOS and then this rom again.
Steps:
Stock Rom -> LeaOS-PHH (AOSP) - It didn't work can't install or update apps from store
Stock Rom -> LeaOS-PHH (AOSP) -> LeaOS -> LeaOS-PHH (AOSP) - Everything works
I installed magisk and securize phh to pass safetynet.
Everything is working now, great work!
Click to expand...
Click to collapse
OK.. Thanks...I will do a test. I just updated my pr to version 8.0.0.416
amonpaike said:
also was-lx1a (my p10 lite 4gb ram)
Click to expand...
Click to collapse
zuldorak said:
I followed every step in the guide and it didn't work but I got it working by installing your leaOS and then this rom again.
Steps:
Stock Rom -> LeaOS-PHH (AOSP) - It didn't work can't install or update apps from store
Stock Rom -> LeaOS-PHH (AOSP) -> LeaOS -> LeaOS-PHH (AOSP) - Everything works
I installed magisk and securize phh to pass safetynet.
Everything is working now, great work!
Click to expand...
Click to collapse
Hi
I have correct the problem, for the moment just format data before flash img
Thanks! Having an alternate OS to choose from is just what I was hoping for! Appreciate all the work you put in Can't wait to test this
AltairFR said:
Non-Official AOSP for Huawei (prague, mediapad, warsaw, rhone) - LeaOS-PHH
LeaOS is a project which based on AOSP with phhusson's Treble GSI patches. I have added my personnals patches for Huawei devices : Encryption, Signal Strengh, Speed Boot, Assisted GPS, NFC, Media App, Default Sound, MediaScanner fixes etc..) and some eremitein patch
Changelog :
LeaOS-PHH May 2022 version
Initial build from PHH AOSP A11-r48 (October)
Add support of data encryption
Add NFC Quick Setting (NFC by default are disabled)
Add Android SPL (Nov, Dec 2021, Jan, Feb, March 2022)
Add Default sound (ringtones, alarm and notification)
Add Huawei bootanimation (no sound)
Add support of multi-user
Pass SafetyNet
Fix Signal strenght indicator (and icon)
Fix Media App permission
Fix MediaScanner crash
Fix Slow-Boot
Pre-requisite :
You must have TWRP installed, use this one (make sure to have the unofficial Android 11 one ! ). To install follow this guide "How to unlock Huawei P8 ligt 2017 (en).pdf" or french version "How to unlock Huawei P8 ligt 2017 (fr).pdf"
Installation (crypt or uncrypt)
Download file : "LeaOS-PHH-20220610-iceows-pra.7z" and extract img file
boot to TWRP
Wipe internal storage, format data
flash this file 1-Huawei-DataPrep-UnCrypt-A-v1.0-signed.zip to disable storage encryption or this file 1-Huawei-DataPrep-Crypt-A-v1.0-signed.zip to enable it. This zip change fstab file, wipe data partition and recreate subfolder /data/user*, /data/system* and /data/vendor*)
Wipe system, cache, dalvik/art cache
reboot to bootloader
run: fastboot flash system <drag system.img here>
(optional) flash Siberia kernel : fastboot flash kernel <drag Siberia.img here>
reboot to TWRP
resize system
flash this file 2-Huawei-system-UnCrypt-v1.3-signed.zip to not-allow data encryption or this file 2-Huawei-system-Crypt-v1.3-signed.zip to allow it
(optional) flash AGPS patch : 2 - AGPS-FIX-AltairVendor-v3.3-signed.zip
reboot to System and set up the phone with Lineage first start assistant. You can also add most user
(optional) reboot to TWRP to install now Google Apps : Google Apps Lite (LiteGapps_Core_arm64_11.0_v2.5_official.zip)
Enjoy !!!
Update (crypt or uncrypt)
Download file : "LeaOS-PHH-20220610-iceows-pra.7z" and extract img file
boot to TWRP
Wipe system, cache, dalvik/art cache
reboot to bootloader
run: fastboot flash system <drag system.img here>
(optional) flash Siberia kernel : fastboot flash kernel <drag Siberia.img here>
reboot to TWRP
resize system
flash this file 2-Huawei-system-UnCrypt-v1.3-signed.zip to not-allow data encryption or this file 2-Huawei-system-Crypt-v1.3-signed.zip to allow it
(optional) flash AGPS patch, Google Apps :
1 - Google Apps lite (LiteGapps_Core_arm64_11.0_v2.5_official.zip)
2 - Enable AGPS (2 - AGPS-FIX-AltairVendor-v3.3-signed.zip)
reboot to System
Enjoy !!!
Source Code:
https://github.com/Iceows
ROM OS Version: Android 11
ROM Kernel: Linux 4.4.x (stock 4.4.26 or Siberia_4.4.302-1.1.zip)
ROM Firmware Required: EMUI 8
Based On: PHH AOSP
Credits:
DarkJoker360
PHH
Andy Yan
Hamido
eremitein
And all the others who tested my patches and helped me improve this ROM
Support Group
Click to expand...
Click to collapse
Hey, can you fix wireless screen cast because if want to enable screen mirriroring on any tvs etc. , my huawei pra lx 1 do a soft reboot. Then it didn't connect :-(
MinhniNG said:
Hey, can you fix wireless screen cast because if want to enable screen mirriroring on any tvs etc. , my huawei pra lx 1 do a soft reboot. Then it didn't connect :-(
Click to expand...
Click to collapse
Hard job, I will try to backport from LeaOS Lineage Version
Hi, I've been using this rom for some days and everything's working fine no reboots or anything I also find it faster than your other LeaOS.
This is just minor stuff but is it possible to add the styles option on the Display settings? I find the style option on phh customization a bit lacking and it doesn't work well. also the huawei animation on boot is faster than usual.
Like I said its minor visual stuff, everything working so far I love how fast this rom is, amazing job!
MinhniNG said:
Hey, can you fix wireless screen cast because if want to enable screen mirriroring on any tvs etc. , my huawei pra lx 1 do a soft reboot. Then it didn't connect :-(
Click to expand...
Click to collapse
Fix, please download Jun version
Why am I getting this error??....
I appricciate your work on the phone oficcialy dead from some time but I'd like to point you on sometihing:
I'm normal guy and I'm not flashing phone on regular basis every day. I do it when I need this, every few monts or years and I've done it few times. What really annoyes me is the fact that your guide for installation is unclear because I'm always following steps VERY CAREFULLY and if installation is unsucessfull after few tries, it's of course because I'm missing something here... Sorry but I already wasted 6 hours of my day off trying to install your rom using your guide so I really appriciate answer for my question: why am I getting this error ???