Related
Hello guys,
I know this might not be a problem for most of you, but for me it is :|
I tried to install a custom rom (Pixel Rom or CM9) but i got stuck. I used a tutorial, and then I tried to install Pixel ROM with TWRP recovery. After installing and rebooting, the phone gets stuck on the ROM's logo. I waited at least 15 minutes for every ROM but it won't pass it..
What can I do ? How can I make my phone work again ?
dsorinn said:
Hello guys,
I know this might not be a problem for most of you, but for me it is :|
I tried to install a custom rom (Pixel Rom or CM9) but i got stuck. I used a tutorial, and then I tried to install Pixel ROM with TWRP recovery. After installing and rebooting, the phone gets stuck on the ROM's logo. I waited at least 15 minutes for every ROM but it won't pass it..
What can I do ? How can I make my phone work again ?
Click to expand...
Click to collapse
did you do a data wipe, factory reset, before flashing one of those roms? try going back and wiping data, then flash one of those roms.
simms22 said:
did you do a data wipe, factory reset, before flashing one of those roms? try going back and wiping data, then flash one of those roms.
Click to expand...
Click to collapse
I did everything, but nothing worked with custom rom, then I flashed an official rom and started all over again with installing CMW, and now I managed to instal Pixel rom.
Anytime you decide to flash a new ROM make sure you follow whatever instructions the ROM developer has laid out. Proper wipe followed by flashing the ROM itself and then Gapps if not included in your ROM.
And never flash a custom kernel until after the first boot.
If you get stuck in a bootloop just pull your battery and hold Volume up + power to boot into your bootloader and select recovery and try again.
thanks for the advice guys I managed to install Pixel Rom
Looking for some input on clean ROM on the TF300T,
This is my second time trying to install it and both times it was successful, however as soon as the boot image loads up it stays stuck loading... I did download the file again thinking it may have been corrupted.
It has been sitting there loading for 20 minutes now.
I am using cwm the latest version and I did not install a kernel still running stock
Any ideas on what could cause this?
chibra said:
Looking for some input on clean ROM on the TF300T,
This is my second time trying to install it and both times it was successful, however as soon as the boot image loads up it stays stuck loading... I did download the file again thinking it may have been corrupted.
It has been sitting there loading for 20 minutes now.
I am using cwm the latest version and I did not install a kernel still running stock
Any ideas on what could cause this?
Click to expand...
Click to collapse
CWM has issues on this unit. Many, many complaints. I use twrp. If you decide to use twrp be sure to choose JB and tf300t version.
Clean ROM is freaking amazing! Seriously just do it I love the mods I can make for it too! Can't wait till I get my volume long press seek mod done! Love this device!
Sent from my SGH-T999
"So I put my phone into airplane mode and threw it... worst transformer ever. -.-" -My friend
tobdaryl said:
CWM has issues on this unit. Many, many complaints. I use twrp. If you decide to use twrp be sure to choose JB and tf300t version.
Click to expand...
Click to collapse
I initially when i first rooted intalled Twrp however i was not able to flash anything at all with it, it would give me errors.... that is the only reason i went to cwm.... I was able to make backups and restores with but ROMs flashing would just fail
chibra said:
I initially when i first rooted intalled Twrp however i was not able to flash anything at all with it, it would give me errors.... that is the only reason i went to cwm.... I was able to make backups and restores with but ROMs flashing would just fail
Click to expand...
Click to collapse
OK. It was just a suggestion since the problem you are experiencing is usually cleared by using twrp.
oryhight sullivan
tobdaryl said:
OK. It was just a suggestion since the problem you are experiencing is usually cleared by using twrp.
Click to expand...
Click to collapse
i m going to give twrp another shot...
i installed http://tinyw.in/5foT
JB version for the TF300T
This is the Rom i m trying to install
http://forum.xda-developers.com/showthread.php?t=2049322
Kernel is still stock and i ve left it that way through the aroma installer
Everytime i flash and reboot i get a boot loop
chibra said:
i installed http://tinyw.in/5foT
JB version for the TF300T
This is the Rom i m trying to install
http://forum.xda-developers.com/showthread.php?t=2049322
Kernel is still stock and i ve left it that way through the aroma installer
Everytime i flash and reboot i get a boot loop
Click to expand...
Click to collapse
I'm sorry it is hard to tell since you have chosen an older twrp to install. The current is five versions later and was updated as the kernels were updated to account for changes. The rom you are flashing is based on 10.4.4.25.
chibra said:
i installed http://tinyw.in/5foT
JB version for the TF300T
This is the Rom i m trying to install
http://forum.xda-developers.com/showthread.php?t=2049322
Kernel is still stock and i ve left it that way through the aroma installer
Everytime i flash and reboot i get a boot loop
Click to expand...
Click to collapse
Use TWRP 2.4.1.0
You are using a very old version of TWRP that has bugs with AROMA installer. So that is most likely where your issues are.
What ROM are you ccoming from? What boot loader are you on.
Sounds to me like you need to upgrade your boot loader and possibly do a full wipe - make sure you are on latest TWRP first otherwise you could brick if you use an older recovery!
sbdags said:
What ROM are you ccoming from? What boot loader are you on.
Sounds to me like you need to upgrade your boot loader and possibly do a full wipe - make sure you are on latest TWRP first otherwise you could brick if you use an older recovery!
Click to expand...
Click to collapse
Wise words. Nobody likes to listen to me so im glad someone else suggested it!
elesbb said:
Use TWRP 2.4.1.0
You are using a very old version of TWRP that has bugs with AROMA installer. So that is most likely where your issues are.
Click to expand...
Click to collapse
Updated the TWRP to the version you mentioned still stuck in boot loop.
sbdags said:
What ROM are you ccoming from? What boot loader are you on.
Sounds to me like you need to upgrade your boot loader and possibly do a full wipe - make sure you are on latest TWRP first otherwise you could brick if you use an older recovery!
Click to expand...
Click to collapse
The only ROM i was able to flash that was fully functioning is cm10.1,
i have also flashed PA 2.9 but had some bugs i couldn't stand (screen rotation not working, extended desktop with no pie)
as for boot loader it says 1.00e by "US _Epad-10.4.2.20-20121228" A03
I just updated the TWRP as recommended on the other post (v2.4.1.0)
on every flash i wipe dalvik / Cache / Factory reset.
Before attempting to boot into Clean Rom i also followed the steps on screen saying to wipe cache and dalvik.
I m hoping PA releases a 3.0 for this device and/or i m able to get Clean rom running
chibra said:
The only ROM i was able to flash that was fully functioning is cm10.1,
i have also flashed PA 2.9 but had some bugs i couldn't stand (screen rotation not working, extended desktop with no pie)
as for boot loader it says 1.00e by "US _Epad-10.4.2.20-20121228" A03
I just updated the TWRP as recommended on the other post (v2.4.1.0)
on every flash i wipe dalvik / Cache / Factory reset.
Before attempting to boot into Clean Rom i also followed the steps on screen saying to wipe cache and dalvik.
I m hoping PA releases a 3.0 for this device and/or i m able to get Clean rom running
Click to expand...
Click to collapse
If you are coming from cm10.1 you will definitely need to do a full wipe as it is non stock. It does say this in the first post. You only do a dalvik and cache wipe when upgrading from the same ROM or in CROMI's case from stock.
Do a data wipe in recovery, make sure you have a titanium backup or equivalent if you want to restore apps.
Success!!!
It worked perfectly fine after i install the back up i did before i flashed my 1st costume rom,
I rooted made a back up at stock/rooted... It just would not install from a full wipe,
it install fine once i flashed that specific backup and dirty flashed then wiped dalvik and cache before booting.
Hi There,
So, I have a Samsung Galax S2 Telus SGH-T989D phone and I decided to root it using the 4.4 KitKat and it went well and everything was great.
However, afterwards to resolve some other issues I was having I decided to make the mistake of loading the gapps which was for another
package into my phone and that messed everything up!
So, I have been struggling with the phone and first it wouldn't let me install another ROM from recovery and kept on giving me error 7 and 6
But, I fixed that and now I can install any ROM from the recovery or Odin (download mode) without any errors.
However:
The phone vibrates , brings up the galaxy logo and then the Koodo logo appears and a bar fills up quickly under it but it never goes away!!!
Phone freezes there and that's that!! Even after taking out the battery I noticed the logo was still stuck on the screen where as normally
it goes blank!!
So, at this point I am not sure what else to do! This is annoying and I'm tired of experimenting. I went through some XDA foroums here and
tried the Super Vipe (taking out the battery has been tried, factory reset and wiping the cache all have been tried)
So, please please please help me out here. I used to have a MyTouch4G which I rooted with CyanogenMod back in the day and it's the most
stable thing ever and all I wanted to do was to perform the same thing on my Galaxy S2 and boom not this time!!!
Awaiting your response and thanks in advance
King-2012 said:
Hi There,
So, I have a Samsung Galax S2 Telus SGH-T989D phone and I decided to root it using the 4.4 KitKat and it went well and everything was great.
However, afterwards to resolve some other issues I was having I decided to make the mistake of loading the gapps which was for another
package into my phone and that messed everything up!
So, I have been struggling with the phone and first it wouldn't let me install another ROM from recovery and kept on giving me error 7 and 6
But, I fixed that and now I can install any ROM from the recovery or Odin (download mode) without any errors.
However:
The phone vibrates , brings up the galaxy logo and then the Koodo logo appears and a bar fills up quickly under it but it never goes away!!!
Phone freezes there and that's that!! Even after taking out the battery I noticed the logo was still stuck on the screen where as normally
it goes blank!!
So, at this point I am not sure what else to do! This is annoying and I'm tired of experimenting. I went through some XDA foroums here and
tried the Super Vipe (taking out the battery has been tried, factory reset and wiping the cache all have been tried)
So, please please please help me out here. I used to have a MyTouch4G which I rooted with CyanogenMod back in the day and it's the most
stable thing ever and all I wanted to do was to perform the same thing on my Galaxy S2 and boom not this time!!!
Awaiting your response and thanks in advance
Click to expand...
Click to collapse
Clean solution: Flash stock firmware via Odin or install custom rom via recovery
LS.xD said:
Clean solution: Flash stock firmware via Odin or install custom rom via recovery
Click to expand...
Click to collapse
Thank you for your reply. However, as I've mentioned before, I've already tried those (from ODIN and through RECOVERY) with multiple different
ROMS and it's not doing anything which is why I am posting this here.
King-2012 said:
Thank you for your reply. However, as I've mentioned before, I've already tried those (from ODIN and through RECOVERY) with multiple different
ROMS and it's not doing anything which is why I am posting this here.
Click to expand...
Click to collapse
Did you perform a FULL wipe? Custom recovery -> format ALL partitions except EFS?
I have tried the Super Vipe off the SD card through the recovery mode and also from recovery I've tried the wipe cache,
factory reset and wipe cache partitions.
I am not sure about "format ALL partitions except EFS" nor am I aware of the procedure.
How would I perform that?
Have you installed a working custom recovery?
Sent from my beloved HTC One S using (most time buggy) Tapatalk
LS.xD said:
Have you installed a working custom recovery?
Sent from my beloved HTC One S using (most time buggy) Tapatalk
Click to expand...
Click to collapse
Yes I'm able to successfully install recovery-clockwork-5.0.2.7-hercules or CWM_Root_Superuser_3.1.3_Busybox_1.20.2
from the recovery without any errors (same if rooted through Odin)
If there's a specific ROM you are thinking about please let me know and I will be more than glad to give it a shot.
You really should use a newer recovery version. But for now go to mounts and storage and format all partitions except EFS. Then try flashing stock firmware via Odin
Here you can get the latest recovery for your device --> TWRP for hercules
LS.xD said:
You really should use a newer recovery version. But for now go to mounts and storage and format all partitions except EFS. Then try flashing stock firmware via Odin
Here you can get the latest recovery for your device --> TWRP for hercules
Click to expand...
Click to collapse
Under mounts and storage and format all partitions except EFS > Don't even see ESF there to begin with..
Do you have a working link for downloading the stock firmware? I have downloaded few and none of them even let me install them (status 0 error)
Any ideas?
Odin is already being used v3.0.7
Format System Data Cache dalvik. Realy... Then flash stock firmware using ODIN!
Sent from my beloved HTC One S using (most time buggy) Tapatalk
LS.xD said:
Format System Data Cache dalvik. Realy... Then flash stock firmware using ODIN!
Sent from my beloved HTC One S using (most time buggy) Tapatalk
Click to expand...
Click to collapse
I was able to finally bring it up!!
Basically I looked for a stock firmware for T-Mobile and after formatting the phones multiple times I tried this ROM
using ODIN and it got rid of the Koodo logo and replaced it with a T-Mobile logo and then it BOOM loaded to start screen finally!! :laugh:
I was about to hammer the phone. So, trust me I was very happy to see it work.
Thank you for your quick and helpful response :good:
Cheers :victory:
Hi all...
I tried to upgrade by Tab 2 7" to KitKat today and failed. I installed Clockworkmod successfully, but then started getting error 7's. I discovered this was because it was outdated. I've tried to install updated clockwork mod which it says has been successful - but doesn't change the original.
I did a backup of my original rom, but this has failed to reinstall. I've tried to put an old version of cyanogen on it, which also has failed, and re-downloaded the stock rom from samsfirmware which passes through ODIN, resets but then the tab 2 hangs on the Samsung screen - flashing.
I can't seem to resolve it.
Has anyone got any ideas? I can't access anything other than clockworkmod - so if you think you know of a way I can successfully upgrade it I may stand half a chance.....
Thanks
Tim
sheltont said:
Hi all...
I tried to upgrade by Tab 2 7" to KitKat today and failed. I installed Clockworkmod successfully, but then started getting error 7's. I discovered this was because it was outdated. I've tried to install updated clockwork mod which it says has been successful - but doesn't change the original.
I did a backup of my original rom, but this has failed to reinstall. I've tried to put an old version of cyanogen on it, which also has failed, and re-downloaded the stock rom from samsfirmware which passes through ODIN, resets but then the tab 2 hangs on the Samsung screen - flashing.
I can't seem to resolve it.
Has anyone got any ideas? I can't access anything other than clockworkmod - so if you think you know of a way I can successfully upgrade it I may stand half a chance.....
Thanks
Tim
Click to expand...
Click to collapse
Use Odin to restore to the stock ROM. Download the stock rom from samfirmware.com and flash it in Odin as PDA. Then, use the latest recovery (either TWRP, CWM, OR PhilZ) from @Android-Andi's recovery thread in the Dev section. You should now be able to flash any ROM you want to. Make sure you do a backup and a wipe system, cache, Dalvik, data, and android secure (if it's an option.)
Sent from my SGH-T989
thanks and....
Thanks so much, does it matter that it won't boot with the stock Roma which I've installed from sams? Will the recovery program still work?
sheltont said:
Thanks so much, does it matter that it won't boot with the stock Roma which I've installed from sams? Will the recovery program still work?
Click to expand...
Click to collapse
What do you mean? Did you flash the stock ROM in Odin?
Sent from my SGH-T989
yep
jrc2 said:
What do you mean? Did you flash the stock ROM in Odin?
Sent from my SGH-T989
Click to expand...
Click to collapse
Yes, I did twice and it's still hung after apparent success installation according to Odin. I've tried it twice.
No success
Thanks
What I've done tonight is reflashed the original Rom - this time it blew away Clockworkmod. It still wouldn't boot. I then put a recovery solution on from your link, which has flashed well. However I've then tried three ROMS and each have hung after installation on the initial boot.
I'll try them again tomorrow night - but do you have any idea why three ROMS plus the stock keep failing?
Thanks
Tim
sheltont said:
Thanks
What I've done tonight is reflashed the original Rom - this time it blew away Clockworkmod. It still wouldn't boot. I then put a recovery solution on from your link, which has flashed well. However I've then tried three ROMS and each have hung after installation on the initial boot.
I'll try them again tomorrow night - but do you have any idea why three ROMS plus the stock keep failing?
Thanks
Tim
Click to expand...
Click to collapse
Did you wipe system, cache, Dalvik cache, and data before flashing and wipe cache and dalvik after flashing? And your tablet will bootloop after a reinstallation in Odin because Odin does not wipe before installation. After flashing in Odin, reboot recovery (make sure tablet is unplugged,) and wipe data, cache, and dalvik cache. Reboot and you should be good to go.
Sent from my SGH-T989
good idea but still no success....
jrc2 said:
Did you wipe system, cache, Dalvik cache, and data before flashing and wipe cache and dalvik after flashing? And your tablet will bootloop after a reinstallation in Odin because Odin does not wipe before installation. After flashing in Odin, reboot recovery (make sure tablet is unplugged,) and wipe data, cache, and dalvik cache. Reboot and you should be good to go.
Sent from my SGH-T989
Click to expand...
Click to collapse
Hi, I've retried all that this morning-i must admit that I didn't know about wiping cache after install, however it's not made any difference, and still hangs on first boot...
Any other ideas? Thanks for all your help.
Happy success
Hi all
Thanks for all your help,especially rcj! I have managed to recover my device using cynagodmod 9 - it wont run 10 or 11 but at least its up and working - even if it's a downgrade from the Android version I was on Really don't care as I can use it again with a lot more memory.
Thanks - without you I would never have found Phils ROM which enabled me to get this far.
Tim
sheltont said:
Hi all
Thanks for all your help,especially rcj! I have managed to recover my device using cynagodmod 9 - it wont run 10 or 11 but at least its up and working - even if it's a downgrade from the Android version I was on Really don't care as I can use it again with a lot more memory.
Thanks - without you I would never have found Phils ROM which enabled me to get this far.
Tim
Click to expand...
Click to collapse
Which version of PhilZ? And I have found that TWRP 2.7.1.0 works better than other versions for KK.
Sent from my SGH-T989
Use latest Philz touch recovery. And use the rom and gapps compatible to your tab. Don't forget to reset to factory setting, clear cache and wipe dalvic cache before flashing the rom and gapps ☺
Sent from my GT-P3100 using XDA Free mobile app
Hi there!
Guys....I need some clues on how to handle with this problem.....
I have my 5.0 LRx210 rooted and installed TWRp recovery by use of Nexus Root Toolkit...the root and the recovery just work fine...
Somehow I managed to try flashing my favorite roms....like Pure White Rom/Xtrasmooth2.4/Cataclysm....and so on..
I have got success only on Pure White Rom...for other roms after successful flashing it just keeps saying: No OS installed are you
sure you wish to reboot. For those roms I have tried both Full Wipe flash and Dirty Flash...but got no success..I don't know why?
Come to the blind end now.... I am just staying on Pure White rom waiting for solution....
hope someone here guide me something...thank you
ayirusp
Thailand
Even if TWRP says no OS try booting up it should work.
Sent from my Nexus 5 using XDA Free mobile app
shri_chanakya said:
Even if TWRP says no OS try booting up it should work.
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
Thank you bro
I did try it already...just stuck on the boot black screen with google logo.....
Although try updating the TWRP recovery to the latest 2.8.2.0, or even CWM recovery....just got the the same result.
The flashing process is mentioned as Successul.., but then when pushing the reboot button it just shows me the above mentioned sentence....
thanks anyway
ayirusp said:
Thank you bro
I did try it already...just stuck on the boot black screen with google logo.....
Although try updating the TWRP recovery to the latest 2.8.2.0, or even CWM recovery....just got the the same result.
The flashing process is mentioned as Successul.., but then when pushing the reboot button it just shows me the above mentioned sentence....
thanks anyway
Click to expand...
Click to collapse
Try flashing TWRP 2.8.1.0 in fastboot and try flashing a rom again, 2.8.2.0 can be quirky for some users.
gee2012 said:
Try flashing TWRP 2.8.1.0 in fastboot and try flashing a rom again, 2.8.2.0 can be quirky for some users.
Click to expand...
Click to collapse
Thank you Bro...
Yes...I do apply root and TWRp recovery 2.8.1.0 via Nexus Root Toolkit 1.9.8....at first.....but it just keeps saying NO OS installed...after finish flashing another rom like Xtrasmoot/Stock5.0 flashable/Cataclysm and bla..bla...bla....(except for Pure White Rom which is my current rom)..and trying to reboot the system.
So I decided to try it with other recoveries like 2.8.2.0 and also the latest CWM recovery....Yet I've got no success till now...that's quite weird
(I have tried flashing with both Full Wipe Flash (Data factory/wipe cache/dalvik cache) and Dirty Flash (wipe cache/dalvik cache)...but as you know...no success....
Thanks anyway...
Thailand
ayirusp said:
Thank you Bro...
Yes...I do apply root and TWRp recovery 2.8.1.0 via Nexus Root Toolkit 1.9.8....at first.....but it just keeps saying NO OS installed...after finish flashing another rom like Xtrasmoot/Stock5.0 flashable/Cataclysm and bla..bla...bla....(except for Pure White Rom which is my current rom)..and trying to reboot the system.
So I decided to try it with other recoveries like 2.8.2.0 and also the latest CWM recovery....Yet I've got no success till now...that's quite weird
(I have tried flashing with both Full Wipe Flash (Data factory/wipe cache/dalvik cache) and Dirty Flash (wipe cache/dalvik cache)...but as you know...no success....
Thanks anyway...
Thailand
Click to expand...
Click to collapse
Well if it we`re me i`d reflash the factory image and start over from scratch, then install TWRP 2.8.1.0 and flash superSU.zip 2.3.5 and flash a custom rom.
gee2012 said:
Well if it we`re me i`d reflash the factory image and start over from scratch, then install TWRP 2.8.1.0 and flash superSU.zip 2.3.5 and flash a custom rom.
Click to expand...
Click to collapse
Yeah...I reflashed it with factory image 5.0 LRX21O downloaded from Official Google Resource and began the whole process of rooting and recovery installation (TWRP 2.8.1.0 and SuperSu.zip..offcourse).....and then started flashing custom roms...the only rom that I could get through with success is Pure White Rom......for other roms it just had been like I mentioned above......
.....I can not figure it out now....why?
Thank you my Bro....
ayirusp said:
Yeah...I reflashed it with factory image 5.0 LRX21O downloaded from Official Google Resource and began the whole process of rooting and recovery installation (TWRP 2.8.1.0 and SuperSu.zip..offcourse).....and then started flashing custom roms...the only rom that I could get through with success is Pure White Rom......for other roms it just had been like I mentioned above......
.....I can not figure it out now....why?
Thank you my Bro....
Click to expand...
Click to collapse
Because some things on your phone are messed up and figuering out what that is/are will probably take longer then starting over imo.