Hi all, I'm writing few lines to guide in the use of a DS4 controller with PS4 Remote Play on Poco F1, and perhaps with any other MIUI based phone.
Starting point: stock Miui 10.1 (Android Pie), stock recovery, rooted with Magisk 18.0 from latest official Twrp just fastbooted.
The requisites are the following:
- install modules Sony Framework v1, 1Controller and SELinuxModeInverter4Magisk v1.0.5A(17000);
- obtain PS4 Remote Play 2.6.0 modded, from another thread here on XDA (latest version 2.7.0 bypasses MagiskHide and detects root, while this modded version doesn't update itself);
- buy and install from Play Store USB/BT Joystick Center 2019 (working substitute for Sixaxis, because MIUI lacks the needed bluetooth drivers and I was not able to have it working over usb);
- use a OTG usb 3.0 cable to connect DS4 and phone.
Now you can map your DS4 with USB/BT JC 2019 in touch emulator mode and enjoy a near-the-original experience playing PS4 Remote Play!
Credits and thanks to all the guys who did the hard work!!!
What about connect my controller with bluetooth?
byjoaxel said:
What about connect my controller with bluetooth?
Click to expand...
Click to collapse
For my experience at the moment it is not possible neither with Sixaxis nor with BT / USB Joystick Center.
It is always possible to install a custom ROM that includes the Bluetooth drivers needed by Sixaxis to work properly.
I'm focused on trying to make Remote Play work at its best on the MIUI stock, just rooted. If I make further progress I will report them here, I hope others will do the same
How did you remove the on screen keypads? Thanks!
This is interesting i have the app set up om my Samsung galaxy tab s3 rooted with magisk. But i can only get it to work on the local network
Sent from my SM-N960U using Tapatalk
ksngdghnt said:
How did you remove the on screen keypads? Thanks!
Click to expand...
Click to collapse
On screen stil there; it's a modded version only to fake version number because the most recent ones do not start with magisk
cdeitrich00 said:
This is interesting i have the app set up om my Samsung galaxy tab s3 rooted with magisk. But i can only get it to work on the local network
Sent from my SM-N960U using Tapatalk
Click to expand...
Click to collapse
Official Remote Play works only over wifi, not strictly over lan.
But you can try a module called Fake Wifi, if your rom allows you to install Xposed framework.
cdeitrich00 said:
This is interesting i have the app set up om my Samsung galaxy tab s3 rooted with magisk. But i can only get it to work on the local network
Sent from my SM-N960U using Tapatalk
Click to expand...
Click to collapse
if you want to do remote play away from home is what you mean, try adding tcp/udp port on your ps4s router
---------- Post added at 05:47 AM ---------- Previous post was at 05:44 AM ----------
BloWer_79 said:
On screen stil there; it's a modded version only to fake version number because the most recent ones do not start with magisk
Click to expand...
Click to collapse
any idea on how to modify the apk to remove the o screen buttons? beeb trying for days. no luck. it sucks specially on my s6. it covers up almost the whole screen. thanks btw
BloWer_79 said:
It is always possible to install a custom ROM that includes the Bluetooth drivers needed by Sixaxis to work properly.
Click to expand...
Click to collapse
Sure it's possible, except those of us who want it can't figure it out, and those who probably know don't care :\
DS4 doesn't work at all in any custom ROM I've tried.
And now, the only way to get DS4 working on stock, is via USB and by buying some app?
I regret buying this phone, I only really got it for gaming :\
CosmicDan said:
Sure it's possible, except those of us who want it can't figure it out, and those who probably know don't care :\
DS4 doesn't work at all in any custom ROM I've tried.
And now, the only way to get DS4 working on stock, is via USB and by buying some app?
I regret buying this phone, I only really got it for gaming :\
Click to expand...
Click to collapse
What app is that
Sent from my SM-N960U using Tapatalk
cdeitrich00 said:
What app is that
Sent from my SM-N960U using Tapatalk
Click to expand...
Click to collapse
Sixaxis something-or-rather, there is a free "test" app.
Hi, I'm also trying to get the app and a controller working but on my Nvidia Shield Tv.
So far I could get the app to work but I couldn't connect any controller to it.
My case is even stranger because the Shield Tv supports many controllers via BT, also DS4 controller. And this controller works in every app without any issues, just not in the ps4 remote play app :/
My ultimate goal would be to use my Xbox one controller for input.
In the app there's the option to register a DS4 controller but it does not work for me..
I did not try sixaxis controller app yet, do you guys think with this app I could register the controller in ps4 remote play app?
And about on screen buttons:
With the help of apps Tasker and AutoInput plugin I could map xbox one controller input to touch input on the coordinates where the on screen buttons are. However if nothing is pressed for a short time, the on screen buttons disappear and my touch input doesn't work until I move mouse cursor and get the onscreen buttons show up again :/
Will they disappear once a DS4 controller is properly connected?
If so, I could then map xbox one controller button presses to the DS4 controller
I just need to get the damn DS4 controller properly connected to the ps3 remote play app -_-
CosmicDan said:
DS4 doesn't work at all in any custom ROM I've tried.
Click to expand...
Click to collapse
It works on resurrection remix but only through bluetooth
ds3 works for me using sixaxis app and this mappinghttps://drive.google.com/file/d/15M1pP_enO5HzWTlJwKAQyku0mQmTzAHy/view?usp=drivesdk
hope it helps. the only problem is that the on screen buttons is still visible. cant see a way to modify the app and remove it
ksngdghnt said:
ds3 works for me using sixaxis app and this mappinghttps://drive.google.com/file/d/15M1pP_enO5HzWTlJwKAQyku0mQmTzAHy/view?usp=drivesdk
hope it helps. the only problem is that the on screen buttons is still visible. cant see a way to modify the app and remove it
Click to expand...
Click to collapse
Which Rom and Kernel are you using ?
Are you using specific magisk modules ?
SerpentSpirale said:
Which Rom and Kernel are you using ?
Are you using specific magisk modules ?
Click to expand...
Click to collapse
im using stock android nougat for my s6
magisk v19.3
magisk manager v7.2
remote play v2.8
Twisted Prime said:
It works on resurrection remix but only through bluetooth
Click to expand...
Click to collapse
Hi, I am in pe custom rom, and I can play with the controller to other games connected to Bluetooth normally. But when in connecte it in the part of the app "register" it doesn't register and I make all that puts in the text, I have redmi note 7. And when I connect normally with Bluetooth the app doesn't recognize it and I only can play with fingers
So maybe you guys can help me. Sorry for resurrecting an older thread but I need some help with this one.
I currently have magisk (v18) and remote play (v2.8) comes on with magisk hide. However no matter what wifi I use, the ps4 will not register to my device. And when I try to use the 8 digit pin, it says failed to register. So what else can I try?
Anyone have any luck using the new one on rooted devices? I always get that 88001003 error. I'm on a rooted OnePlus 7 pro Android 10 stock.
Related
im running cyanogen rom and downloaded the sixaxis app, the checker recognizes the inputs, but i cant get the controller to work with any emulator. what am i doing wrong. i have the checker app and the main app. i changed keyboard input in settings also
Turn off/uninstall the compatibility app
Sent from my Sensation using XDA Premium App
thanx alot, I got fpse to work but nothing else. im able to set the hardware keys up on other emulators, but in-game it doesnt respond for some reason
I've tried using this for gameboid, snesoid and n64oid. I'm able to set up the hardware keys in the settings but while I'm in-game, I get no response. I'm running cyanogen selfkang3 any ideas? Maybe different emulators?
Sent from my Sensation using XDA App
bug
mikaeldalc said:
thanx alot, I got fpse to work but nothing else. im able to set the hardware keys up on other emulators, but in-game it doesnt respond for some reason
Click to expand...
Click to collapse
for some reason the Sixaxis app still has bugs and the DEV said he will fix them in upcoming releases, just stay tune for updates.
k kool that works. what about the wiimote, does that work better at this time?
matury said:
for some reason the Sixaxis app still has bugs and the DEV said he will fix them in upcoming releases, just stay tune for updates.
Click to expand...
Click to collapse
Actually this has nothing to do with any bugs in the Sixaxis app or otherwise. All of the *oid emulators require that you enable Settings->Other Settings->Use Input Method.
Alternatively you can try the new 'Bypass IME' setting under preferences, which will allow you to still use a soft keyboard while the app is running.
sir_earl said:
Actually this has nothing to do with any bugs in the Sixaxis app or otherwise. All of the *oid emulators require that you enable Settings->Other Settings->Use Input Method.
Alternatively you can try the new 'Bypass IME' setting under preferences, which will allow you to still use a soft keyboard while the app is running.
Click to expand...
Click to collapse
well... thats what I got from the DEV in a note I ask the same question and I got that.. thanks for a more detail ver.
Has anyone got a PS3 controller working on their sgs2 skyrocket? I downloaded the app and it keeps force closing on me which makes me think its incompatible. Right now I'm on stock rom with Da_G's 0.3 kernel, are there any roms that support the sixaxis controller for this phone?
Sent from my SGH-I727R using XDA App
Did you try the sixaxis compatibility app? You should use that before buying the controller app.
I downloaded the compatibility app, but haven't tried it yet.
I also downloaded Blues IME, but haven't tried it either.
I got it working with the new update. Works perfectly after some settings changes
Sent from my SAMSUNG-SGH-I727 using xda premium
How did you get it working? I couldn't get it to work at all with either app.
mdz24cavalier said:
How did you get it working? I couldn't get it to work at all with either app.
Click to expand...
Click to collapse
Same. What new update and settings are you referring to?
Anyone else?
Sent from my SAMSUNG-SGH-I727 using XDA App
Downloaded the Sixaxis Compatibility Checker this morning and it seems to pair fine. I'll check my controller when I get home tonight. The Connection type 2 looks to be supported, I'll just need to update the master address with the SixaxisPairTool for it to work. Update later.
Stock (2.3.5) / Rooted
Ok, I tried this all again.
My superuser was not allowing the Sixaxis Compatibility checker to work.
I then downloaded the SixaxisPairTool to set the address of my Dual Shock 3 controller with my PC to XX:XX:XX:00:00:00. The address being what ever your phone list it as in the capability app. This lets the phone see the controller.
I then re-downloaded Bluez IME.
I'm having some trouble staying connected if I set the controller down for a few seconds. Make sure to select "Phonejoy" as the device driver!
I'll update more once I get time to mess around with it more.
Sixaxis controller works perfect for me. Stock Rogers ROM rooted. It's awesome playing street fighter with this!
I am trying to connect a wired Xbox 360 controller to my Samsung Galaxy Tab 2 10.1 tablet (running Samsung's stock Android 4.1.1 ROM) via. an OTG adapter.
When I connect it, the following two messages appear:
"High-power USB device connected."
"Can not access to this device. "Connected device needs power supply."
Due to this, USB/BT Joystick Centre can't detect the controller.
Due to the poor English in the second message, I am presuming it's a Samsung ROM issue, rather than an Android/a tablet hardware issue.
Any ideas?
I have same problem with my tab 2 7.0
Sent from my GT-P3110 using xda premium
I also had this problem.
If you plug the joypad into the OTG connector first and then the OTG into the tablet it should work.
at least it did for me.
hope this helps.
xzodia said:
I also had this problem.
If you plug the joypad into the OTG connector first and then the OTG into the tablet it should work.
at least it did for me.
hope this helps.
Click to expand...
Click to collapse
I can't believe that worked! Thank you.
Now USB/BT Joystick Center detects the hardware, and all keypresses. However, no other apps seem to detect any keypresses (e.g. Mupen64Plus, XBMC 12.0 BETA 2 etc.)
King Mustard said:
I can't believe that worked!
Thank you!
Click to expand...
Click to collapse
Your welcome
King Mustard said:
Now USB/BT Joystick Center detects the hardware, and all keypresses. However, no other apps seem to detect any keypresses (e.g. Mupen64Plus, XBMC 12.0 BETA 2 etc.)
Click to expand...
Click to collapse
Yeah i had the same problem on my tablet which is rooted.
But it works perfectly on my sons which is not rooted.
I read somewhere that it had issues if luckypatcher was installed.
but never looked into it anymore as i use a ps3 pad via sixaxis controller app, which allows me to have the tablet on charge while playing.
My Tab had version 6.41 (cracked)
and my sons had 6.44 (paid for)
not sure if the issue is related to the version number or the fact my sons is not rooted and never had luckypatcher on it.
Either way, if your rooted and can get hold of a ps3 pad that is the best way imo.
Other than that make sure you have switched the IME to joypad before opening the emulator and then go to input settings and bind the controllers.
i have got epsxe, mupen, snesgnes all working with both apps, but on different tablets (1 rooted, 1 not)
hope this info helps you figure it out.
I tried what u said but the remote curcle just flashes but doesnt work!!
Sent from my MT11i using xda premium
mitchellreece said:
I tried what u said but the remote curcle just flashes but doesnt work!!
Sent from my MT11i using xda premium
Click to expand...
Click to collapse
Make sure you use USB/BT Joystick Center from the Play Store.
Anyone know where I can get the configuration for controles found some but.. Not mc3/4 I went to joysick web page but they only have for playstation controller not xbox!! Thanks
Sent from my Neo V UHD using Xda Premium
Anyone???
Sent from my Neo V UHD using Xda Premium
mitchellreece said:
Anyone???
Sent from my Neo V UHD using Xda Premium
Click to expand...
Click to collapse
I've been trying also without succes, i followed some tutorials but didn't end up with a working xbox controller
Now I noticed the changelog of CM10.1 says :
Code:
Changes in 20130131 cm10.1 nightly for p3100
Built on Jan 31st (11:31)
Enable wireless Xbox 360 controller support
MERGED ON JAN 30TH AT 22:01:20 IN ANDROID_VENDOR_CM
So I installed CM10.1 & tested with an usb otg but without succes, so my question : does anybody managed to make a tab2 work with his wireless xbox controller ?
King Mustard said:
I can't believe that worked! Thank you.
Now USB/BT Joystick Center detects the hardware, and all keypresses. However, no other apps seem to detect any keypresses (e.g. Mupen64Plus, XBMC 12.0 BETA 2 etc.)
Click to expand...
Click to collapse
So mate, have you managed to put it to work? Ordered my OTG cable so i might be joining this adventure soon on my 7" galaxy tab
Yes i have it working fine with stock rom!! I just need the control configuration for gta vice city!
Sent from my Neo V UHD using Xda Premium
Need Help
King Mustard said:
I can't believe that worked! Thank you.
Now USB/BT Joystick Center detects the hardware, and all keypresses. However, no other apps seem to detect any keypresses (e.g. Mupen64Plus, XBMC 12.0 BETA 2 etc.)
Click to expand...
Click to collapse
Hi King Mustard what did you do to make it work I have the same problem as yours on my tab this is the otg cable I bought
View attachment 1851908
kirhidemi said:
Hi King Mustard what did you do to make it work I have the same problem as yours on my tab this is the otg cable I bought
View attachment 1851908
Click to expand...
Click to collapse
No 30 pin on this thing bud
King Mustard said:
Make sure you use USB/BT Joystick Center from the Play Store.
Click to expand...
Click to collapse
My joystick center connect to my xbox controller and he stops flashing but I still cannot do anything on it. Can someone help me please?
I have a wired 360 controller, and a otg cable. I have everything all hooked up, but when I go to my Octopus app, it tells me there is no device conected and all my xbox 360 controller does is flash green for a while then it will light up player 1 and when I move the sticks on it, it goes back to flashing green. I tried to use a Xbox One controller, the octopus app days there's a xbox one controller hooked to my phone, but when I go to use it, it just makes stuff happen on my xbox one system. PLEASE HELP! I probably wont be getting on this much so if you can just text my number at 606 280 6727
xxBlueVoid25xx said:
I have a wired 360 controller, and a otg cable. I have everything all hooked up, but when I go to my Octopus app, it tells me there is no device conected and all my xbox 360 controller does is flash green for a while then it will light up player 1 and when I move the sticks on it, it goes back to flashing green. I tried to use a Xbox One controller, the octopus app days there's a xbox one controller hooked to my phone, but when I go to use it, it just makes stuff happen on my xbox one system. PLEASE HELP! I probably wont be getting on this much so if you can just text my number at 606 280 6727
Click to expand...
Click to collapse
There's 1. Some ROM side changes needed (you could check old cm-11.0 source, if I remember right they had it in)
And 2. Some kernel changes needed which means you need to compile your own kernel ( https://github.com/kumajaya/android...mmit/3e18d344759a71d937163930198a4bab1630784e )
Good luck!
https://raw.githubusercontent.com/L....1/data/keyboards/Vendor_045e_Product_028e.kl
You could try saving it in
system/usr/keylayout/Vendor_045e_Product_0719.kl
Make sure giving it proper rights.
Latest Custom ROMs by me have Xpad support enabled by default in it's kernel.
Edit:
https://github.com/LineageOS/android_vendor_cm/commit/918a7eaf8d0ddfad8a2c8f705417076ef74b7bbd
Here, I've coded this in a weekend when I ran out of ideas for my other project, and just wanted to share it with you
What it is?
XPlayR is a remote bluetooth gamepad (no analogs for now!) implementation to be used with the XPERIA Play.
It implements an InputMethodService in the server side to send key events to the controlled application.
As there are no non-rooted way to inject touch events into the UI, i'm not bothering to implement remote touch events (i.e. On-screen controls only games, like games that doesn't fully rely on key events). If anyone knows how to do it, then tell me!
Actually it's designed to support up to 4 clients (a.k.a. 'Controllers') via button mapping at server side (only 3 possible mappings are implemented), tested it with 2 controllers at a time, but don't know what would happen if more than 2 clients are connected, as I saw some lag because it uses bluetooth, there are some keycodes that are available only after SDK 11 (min version is 10) and maybe the device could handle only a number of key events at a time.
Installation
Install the client on the XPlay's that you would like to use as gamepads.
In the server (tablet or somethig like that), you must enable and change the input method to that of 'XPlayR Remote Pad'
Remember to change this setting back after you finish gaming because it doesn't handle text edition for now!
How to use it?
First, you must pair the clients with the server, using the device's own method to do so (i.e. Settings > Connectivity > Bluetooth > Pair device...)
Then in the client, open the menu, and select 'refresh devices', touch the server name, and then wait for it to connect.
Remember, the fastest to connect gets controller 1!
You'll know what controller you got looking at the LEDs on the bottom of the screen.
I could've made this a paid software, but I'm too lazy to do so...
Also, I like to return something to the community because what I get from it (ROMS, KB, and so on) is far expensive than what I'm giving.
Tested it with RetroArch, DraStic, PPSSPP and Mupen64Plus AE on a Galaxy S4 i9500
Server and Client attached.
So, hope you like it
I did what you said to do and then it just keeps getting errors saying unable to connect :/
Sent from my GT-I9300 using XDA Premium 4 mobile app
CloudStrife1901 said:
I did what you said to do and then it just keeps getting errors saying unable to connect :/
Sent from my GT-I9300 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Bluetooth was on? Have you enabled the input method in Android's settings? Tried to re-select it after the error? It gives any exact error? What device(s) are you using it on?
Sorry for so many questions
For xplay gingerbread or ics? Can't install on my gingerbread 2.3.7 parcell error
send from GT-N7000
Couldn't get it to work with retroarch... :/
Gesendet von meinem Nexus 7 mit Tapatalk 4
I installed both server and client in a xperia play, xperia mini, and a galaxy S4, ranging from GB up to JB. they ran fine, just some random FCs when BT was off. I need logs to search for possible bugs in other roms.
Retroarch was hard to configure because it has a somewhat complex input config, it's not very user-friendly atm
Some other emus like the *oid series doesn't correctly catch key events sent from the server, at least on my setup.
Can't redownload, the link is dead? Or maybe my connection error, I'm using gin2jellbean v2.20
send from GT-N7000
biozkop said:
Can't redownload, the link is dead? Or maybe my connection error, I'm using gin2jellbean v2.20
send from GT-N7000
Click to expand...
Click to collapse
The apps are in xda's servers so maybe you got a connection error
Yes, it's okay now ..
send from GT-N7000
Some users just don't know how hard coding a single app could be
Awesome work dude, gonna try this when I get my flex replaced :good:
Sent from my R800i using xda app-developers app
working great, but i rather play emu in my xplay, hehe.. it's awesome if someone can make window pc / laptop version...
send from GT-N7000
Works great but sometimes it doesn't connect
Sent from my R800i using xda app-developers app
biozkop said:
working great, but i rather play emu in my xplay, hehe.. it's awesome if someone can make window pc / laptop version...
send from GT-N7000
Click to expand...
Click to collapse
I second this! I'd love to hook up my xplay to my computer and use it as a gamepad.
So can you make it work on my pc
Please
Sent from my R800i using xda app-developers app
yeah, yeah, im posting, and maybe breaking rulez, but this app is awesome!
i tried it on mi sgTab2 with cm11 and my old and loved xperia play stock+lupusv12full
and works perfect.
Awesome work!
thanks!!!
TYWM!
It works great!
xPlay is gin2kk and it works without problem on Xperia ZL in ppsspp.
Only problem in client (Play) is when in landscape mode (slider open) and when is to much paired devices, i can't scroll down, but once deleted list of other paired devices, i can see and connect without problems.
Thanks again
Sent from my C6502 using xda app-developers app
As some said, what the Xperia Play really needs is an app that allows to use it as a gamepad for PC. THAT would be awesome.
Miles Wolf said:
As some said, what the Xperia Play really needs is an app that allows to use it as a gamepad for PC. THAT would be awesome.
Click to expand...
Click to collapse
there's a app that makes that
https://play.google.com/store/apps/details?id=nemex.nJoy
i have used that, and works perfect!
Anyone tried casting your screen to chromecast ?
I tried using the MirrorEnabler method, but it told me there were some essential files missing, and that I might need to flash a custom ROM to be able to cast it.
Has anyone been successful with casting on the Stock ROM ? If not does anyone know what files i'll need to push, in order to get MirrorEnabler to do its thing ?
Any help appreciated !
Thanks
crazyjc81 said:
Anyone tried casting your screen to chromecast ?
I tried using the MirrorEnabler method, but it told me there were some essential files missing, and that I might need to flash a custom ROM to be able to cast it.
Has anyone been successful with casting on the Stock ROM ? If not does anyone know what files i'll need to push, in order to get MirrorEnabler to do its thing ?
Any help appreciated !
Thanks
Click to expand...
Click to collapse
The stock rom actually has casting built in. Swipe the right menu and all the way on the bottom when your device detects the chromecast should be a icon that says cast screen
TekGodRockinLoud said:
The stock rom actually has casting built in. Swipe the right menu and all the way on the bottom when your device detects the chromecast should be a icon that says cast screen
Click to expand...
Click to collapse
This was not enabled in Kitkat.
Is it tested working in Lollipop? i refer to full chromecast mirroring.
Yeah i couldnt find that option either. Havent updated to Lollipop yet. Hope its enabled on that
Anyone with LP confirm screencasting?
The tile is there but when clicking it it results in no devices found.
bjarnehe said:
The tile is there but when clicking it it results in no devices found.
Click to expand...
Click to collapse
Same for me, cast icon present on official lolipop update but no device found
lioo said:
Same for me, cast icon present on official lolipop update but no device found
Click to expand...
Click to collapse
Same here... is a big bummer for me!!!
Carlos
---------- Post added at 11:46 AM ---------- Previous post was at 11:17 AM ----------
Chaleman said:
Same here... is a big bummer for me!!!
Carlos
Click to expand...
Click to collapse
Well, I just tried tihs and it works... http://forum.xda-developers.com/har...experimental-enable-mirroring-device-t2812193
Although, I tried it on a monitor, not a TV, so I'm not sure if the audio works... I will try it later or perhaps someone can jump ahead before i get home
Carlos
lioo said:
Same for me, cast icon present on official lolipop update but no device found
Click to expand...
Click to collapse
WORKS ! I don't know if an update are come but it's works ! (I'm in testing phase without sd card... i hope is not the reason)
Yup this works now!
Google added chromecast support for the tablet
Tried it today. It's awesome! ?
Sent from my SHIELD Tablet using XDA Free mobile app
Mirror casting with shield tablet using Chromecast sucks. I know Chromecast isnt designed for lagless mirroring. Playing and casting videos from your storage is really laggy.
I wished I bought Microsoft wireless display adapter instead. Based on the reviews, it seems to have the highest chance as a cable free solution to the HDMI cable.
Been looking for 2 things:
1. If anyone's actually tried NST with MS WIDI adapter, how was it?
2. Can a Chromecast be hacked to perform like a WIDI adapter, so that the content streaming won't have to go through WiFi and internet?
Hope someone could help. Thanks​!