Database Info

EDL Mode on Redmi Note 5 Pro

Youtube link for the complete process at the end
Step to get EDL on Redmi Note 5 Pro
1. Disassemble the phone
2. remove the battery Metal bracket
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3. Remove Tape from here
4. EDL Pins are just below that
5. Short pins with twizer and insert USB
6. Qualcomm HS-USB QDLoader 9008 (Com7) detected on device manager (driver required)
7. On Mi flash tool tap refresh
Youtube link:

It recognizes usb, but flashing is not possible.

[email protected] said:
It recognizes usb, but flashing is not possible.
Click to expand...
Click to collapse
what error did you get ?

junioreinstein said:
what error did you get ?
Click to expand...
Click to collapse
It looks like an error due to anti-rollback.I will not buy XiaomiPhone.

yes is work...

hi
my phone is brick, there is no connected to my account on my phone, how can I use it again? Will this solution be good for me too?
sorry bad english

Is this working even with anti rollback brick?

Ra2rd said:
Is this working even with anti rollback brick?
Click to expand...
Click to collapse
You'll get PM on your Miui account. But try to flash 2 days after the deadline even if you dont have reply.
waiting for PM

juve60 said:
You'll get PM on your Miui account. But try to flash 2 days after the deadline even if you dont have reply.
waiting for PM
Click to expand...
Click to collapse
Ok thanks! So i'll just wait and cross my fingers :angel:

This method is not needed for anti roll back, it will automatically be detected as 9008 device in com port, no need to dismantle the phone at all !
all you need to do is wait for your account to be authorized after posting your account number in the forums and you will be able to flash !!

bluerichblue said:
This method is not needed for anti roll back, it will automatically be detected as 9008 device in com port, no need to dismantle the phone at all !
all you need to do is wait for your account to be authorized after posting your account number in the forums and you will be able to flash !!
Click to expand...
Click to collapse
Good morning friend, my phone is dead, I already published my ID in a Russian forum, but still do not give me any answer, you know where I got the message or instructions to revive my phone.
The port QDLoader 9008 appears to me but I can not do anything.
It will be that Xiaomi will send me a password for PM or what they will send.
Thank you for responding and greetings from Colombia

...

Flashing an old stock miui rom(not antirollback)
Hi. After I am confirmed to flash my phone by xiaomi. will I be able to flash an old rom(no anti rollback)?
Thanks

eanaranjo said:
Good morning friend, my phone is dead, I already published my ID in a Russian forum, but still do not give me any answer, you know where I got the message or instructions to revive my phone.
The port QDLoader 9008 appears to me but I can not do anything.
It will be that Xiaomi will send me a password for PM or what they will send.
Thank you for responding and greetings from Colombia
Click to expand...
Click to collapse
As long as you sent the account number before the finish date.
You can post here until 24 July, http://en.miui.com/thread-3254707-1-1.html you only need to post the number of the account and then wait a couple of days.
After you need to sign in to miflash too, so that it can verify your account if it tells you that your computer is bound then you can flash the phone !
The instructions will be sent to you in PM in the MIUI account, you must follow every little detail and it will work.
Do not worry if it shows some errors during flashing, DO NOT stop the process , it continues and gives you success message in the end !
Good Luck !!

Please help me
after unlocking my phone i just installed twrp and install custom rom miui 10 on redmi note 5 global and boom it was dead now i came to know that we have to take permission from the develpers and ive submitted my id to this post but today is 26 and i came to know right now after reading this forum
will i be able to have permission to flash because The deadline for collecting Mi ID was July 24th, 2018?
and if yes then how much time it would take?

cant even flash in edl mode
i cannot even flash my phone in edl mode.. it says .."only nop and sig tag can be received before authentication"

Hello,
Take a look to mi6 forum : https://forum.xda-developers.com/mi-6/help/firehose-t3802143?nocache=1
It might work .
If doesn't ask for auth flash last usable rom , unlock bootloader and flash with dummy.img antirbpass partition if you want to downgrade.
Before downgrade antirbpass partition must be cleared (erased).

AngelescuO said:
Hello,
Take a look to mi6 forum : https://forum.xda-developers.com/mi-6/help/firehose-t3802143?nocache=1
It might work .
If doesn't ask for auth flash last usable rom , unlock bootloader and flash with dummy.img antirbpass partition if you want to downgrade.
Before downgrade antirbpass partition must be cleared (erased).
Click to expand...
Click to collapse
did that work for u?

Deleted

Hello,
First of all even if phone is bricked and is in EDL mode EDL mode needs to be restarted using testpoint.
To be able to flash without xiaomi auth account you need in fastboot rom a non auth programmer.
programmer is prog_emmc_firehose_Sdm660_ddr.elf.
Non auth programmers have about 616KB 617KB size. If it's more it contains auth code and will ask for auth account if using latest mi flash tool.
Download last usable miui fastboot version ( version you have used before brick phone).
Download a old fastboot rom as an example 9.5.6.0 or 9.5.13.0 and get from it programmer file.
Overwrite auth programmer file from version you should flash with non auth programmer 9.5.13.0 or from any previous version.
Download miflash tool 2017.4.25.0 and install it.
Get miflashtool portable (latest) 2018.....
Copy programmer to latest miflash tool and test if programmer is compatible with phone and if sahara protocol is launched through COM port.
Restart EDL mode and test sahara http://en.miui.com/forum.php?mod=viewthread&tid=3576914&highlight=sahara+protocol
If protocol was launched Restart EDL mode and flash using 2017 version as soon as possible after restart of EDL mode.
My phone is not bricked but I have flashed in EDL mode via testpoint without xiaomi auth.
EDL mode restart is very important.
Some mi users has already tried this but they have errors about EDL com port comunication with sahara protocol.
Good luck

I think I killed my brand new phone

I've been running the crDroid OOS 10 OB3 ROM since I got my phone two weeks ago and everything was fine and I updated to OB4 today. Well, after I tried changing system ui themeing my phone stopped displaying any system ui at all so I tried to restore my nandroid backup. My nandroid backup took 4 hours then when it got to bluetooth my battery was dying so I had to stop it.
I rebooted into TWRP and tried to clean flash the rom but it gave me errors about mounting the data partition so I tried changing slots.
Well after I changed slots I am stuck in fastboot mode and can't get back to TWRP and adb wont recognize my phone. There's no bootloader or baseband version displayed on fastboot and the product name/variant is msmnile/SDM UFS, my phone is still unlocked if it matters. Someone in the ROM telegram suggested I try the MSM tool but my phone doesn't seem to want to boot into Qualcomm mode and I'm worried that might be a big issue.

Hi!
I really don't know if this helps because you might have already tried it, but I had a similar problem where the normal fastboot mode didnt work and I had no Recovery. Someone suggested, that I should hold Volume Up, Volume down and the Power button all at the same time and from there I was able to revive the phone with the All-In-One Tool...
I quickly looked up the Qualcomm Mode and MSM-Tool you mentioned but I'm still not sure if that is what I just described, so Im posting this just to make sure you tried it because it was a really easy fix when I thought I bricked my phone
Sorry if you already did it, anyway Good Luck!
David

DvdStrbl said:
Hi!
I really don't know if this helps because you might have already tried it, but I had a similar problem where the normal fastboot mode didnt work and I had no Recovery. Someone suggested, that I should hold Volume Up, Volume down and the Power button all at the same time and from there I was able to revive the phone with the All-In-One Tool...
I quickly looked up the Qualcomm Mode and MSM-Tool you mentioned but I'm still not sure if that is what I just described, so Im posting this just to make sure you tried it because it was a really easy fix when I thought I bricked my phone
Sorry if you already did it, anyway Good Luck!
David
Click to expand...
Click to collapse
Well see the issue is I'm trying to get All in One to recognize my phone but it won't seem to boot into EDL mode. I installed the Qualcomm USB drivers but it's still not showing my phone. When I use the key combo suggested to boot into EDL mode my phone does refresh in device manager giving me the qualcomm device so I assume this is download mode just not displaying the text anymore. If i try the key combo with my phone unplugged it takes awhile but eventually goes into fastboot.

In this case I can't help you, i googled EDL, it is what I meant and it was all I got :-/
Wish you good luck

If your bootloader is unlocked try to flash the fastboot rom from fastboot.
https://forum.xda-developers.com/oneplus-7-pro/how-to/rom-stock-fastboot-roms-oneplus-7-pro-t3931424

Bradl79 said:
If your bootloader is unlocked try to flash the fastboot rom from fastboot.
https://forum.xda-developers.com/oneplus-7-pro/how-to/rom-stock-fastboot-roms-oneplus-7-pro-t3931424
Click to expand...
Click to collapse
When I try flashing anything at fastboot it just hangs waiting

viralhysteria said:
I've been running the crDroid OOS 10 OB3 ROM since I got my phone two weeks ago and everything was fine and I updated to OB4 today. Well, after I tried changing system ui themeing my phone stopped displaying any system ui at all so I tried to restore my nandroid backup. My nandroid backup took 4 hours then when it got to bluetooth my battery was dying so I had to stop it.
I rebooted into TWRP and tried to clean flash the rom but it gave me errors about mounting the data partition so I tried changing slots.
Well after I changed slots I am stuck in fastboot mode and can't get back to TWRP and adb wont recognize my phone. There's no bootloader or baseband version displayed on fastboot and the product name/variant is msmnile/SDM UFS, my phone is still unlocked if it matters. Someone in the ROM telegram suggested I try the MSM tool but my phone doesn't seem to want to boot into Qualcomm mode and I'm worried that might be a big issue.
Click to expand...
Click to collapse
what the problem u are facing while flashing from msm tools?

If you haven't fixed your phone yet just use MSMtool it will fix it, this phones essentially unbrickable.

whoamanwtf said:
If you haven't fixed your phone yet just use MSMtool it will fix it, this phones essentially unbrickable.
Click to expand...
Click to collapse
I installed the qualcomm drivers and it showed up in MSM tool and gave me success after 6 seconds but nothing else happened so I unplugged my phone now it says device descriptor failed when I try to go into qualcomm mode
If i uninstall the drivers and try again same thing and trying to use the qualcomm driver files tells me my driver is already up to date

Well you need to hit start once it's connected. https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691 follow the instructions there with the phone being unplugged and powered off open msm hold volumes while not hitting power at all and wait then plug into the computer.

viralhysteria said:
I installed the qualcomm drivers and it showed up in MSM tool and gave me success after 6 seconds but nothing else happened so I unplugged my phone now it says device descriptor failed when I try to go into qualcomm mode
If i uninstall the drivers and try again same thing and trying to use the qualcomm driver files tells me my driver is already up to date
Click to expand...
Click to collapse
During Installing drivers again choose the option (something of) search from internet. And let the file be downloaded and install. Trust me this method works. I too had same problem

whoamanwtf said:
Well you need to hit start once it's connected. https://forum.xda-developers.com/oneplus-7-pro/how-to/msm-tool-guac-t3934691 follow the instructions there with the phone being unplugged and powered off open msm hold volumes while not hitting power at all and wait then plug into the computer.
Click to expand...
Click to collapse
Okay I got the descriptor issue to stop and MSM is detecting the phone again but its still not booting to anything when I run the tool like the guide said it should. I do upgrade mode right?

viralhysteria said:
I installed the qualcomm drivers and it showed up in MSM tool and gave me success after 6 seconds but nothing else happened so I unplugged my phone now it says device descriptor failed when I try to go into qualcomm mode
If i uninstall the drivers and try again same thing and trying to use the qualcomm driver files tells me my driver is already up to date
Click to expand...
Click to collapse
viralhysteria said:
Okay I got the descriptor issue to stop and MSM is detecting the phone again but its still not booting to anything when I run the tool like the guide said it should. I do upgrade mode right?
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-7-pro/how-to/op7pro-collection-unbrick-tools-t3956595
I meant to send that one, follow those instructions and you'll be good. It's Android 9 but that doesn't matter, you can update from there once your phones working again.

whoamanwtf said:
https://forum.xda-developers.com/oneplus-7-pro/how-to/op7pro-collection-unbrick-tools-t3956595
I meant to send that one, follow those instructions and you'll be good.
Click to expand...
Click to collapse
It says to wait about 5 minutes after starting but I get stuck at this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Where did you get the files you're using? Maybe download one from my link, they're the only ones I've personally used and can say for sure they work

whoamanwtf said:
Where did you get the files you're using? Maybe download one from my link, they're the only ones I've personally used and can say for sure they work
Click to expand...
Click to collapse
Your file does the same thing
The connection status switches to N/A but if i stop it and enum it still detects the phone
I used the drivers provided in your link and it still doesnt seem to work
that status bar at the bottom says Running: Upgrade though but thats just an indicator of the job task, no?

viralhysteria said:
Your file does the same thing
The connection status switches to N/A but if i stop it and enum it still detects the phone
I used the drivers provided in your link and it still doesnt seem to work
that status bar at the bottom says Running: Upgrade though but thats just an indicator of the job task, no?
Click to expand...
Click to collapse
Send a larger screen grab of the MSMtool running, I don't recognize what you sent.

whoamanwtf said:
Send a larger screen grab of the MSMtool running, I don't recognize what you sent.
Click to expand...
Click to collapse

So it sounds dumb but try rebooting your computer and switching USB ports then trying again.

whoamanwtf said:
So it sounds dumb but try rebooting your computer and switching USB ports then trying again.
Click to expand...
Click to collapse
Same thing it just assigned a new COM port

[Hisense A5] How to Enter Hardware EDL mode

Hisense A6, A6L, A5 ... can not unlock bootloader
you can enter A5 hardware edlmode
teardown your phone
jump this point with clip(?)
and connect usb cable
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
if can not enter
you need take off power cable ( right bottom corner)
and retry
you can enter EDL mode
you need A5's QFIL firmware

joygram said:
Hisense A6, A6L, A5 ... can not unlock bootloader
you can enter A5 hardware edlmode
teardown your phone
jump this point with clip(?)
and connect usb cable
if can not enter
you need take off power cable ( right bottom corner)
and retry
you can enter EDL mode
you need A5's QFIL firmware
Click to expand...
Click to collapse
Hi, thanks for the useful information.
Previously I bricked my A5 and was able to re-flash with 6.09.06.
I thought I would be able to issue the "adb reboot edl" command. But it didn't seem to work for me.
If I issue the "adb devices" command, I get the response "List of devices attached" with a number and the word "device".
I can do an "adb shell" command ... works well ... can go in there and put in some linux commands.
But when I issue the "adb reboot edl" command, it appears to work. The phone becomes unresponsive. If I issue the command "adb devices", it says that nothing is there.
But when I go into the QFIL program ... there is "No Port Available".
Any ideas ?

try step.
no adb required.
just jump point and connect power cable.
you should retry until catch QFIL catch port.
CrotteDeChien said:
Hi, thanks for the useful information.
Previously I bricked my A5 and was able to re-flash with 6.09.06.
I thought I would be able to issue the "adb reboot edl" command. But it didn't seem to work for me.
If I issue the "adb devices" command, I get the response "List of devices attached" with a number and the word "device".
I can do an "adb shell" command ... works well ... can go in there and put in some linux commands.
But when I issue the "adb reboot edl" command, it appears to work. The phone becomes unresponsive. If I issue the command "adb devices", it says that nothing is there.
But when I go into the QFIL program ... there is "No Port Available".
Any ideas ?
Click to expand...
Click to collapse

Anybody who knows:
How do you open the device without breaking it?
Ehere to begin to open it?
What tools (i.e. screwdrivers T5?) you need?
Does an Edl-Hardware USB-Cable works with the Hisense to enter Edl-Mode? How?

Yeah, how to open the Hisense A5?

Use something like a guitar pic (plastic plectrum) on the edge of the cover and open the cover carefully i.e. upper front.

lillo9546 said:
Yeah, how to open the Hisense A5?
Click to expand...
Click to collapse
I used just my fingernail. You can start opening from the weakest point which is near the sim card port.

Hi Everyone, thanks you your tips.
I went to a phone repair place and paid them 20 AUD to open the phone.
I am having trouble getting the phone into edl mode, (which I found means Extended Download Mode BTW).
Reading more there is information regarding PCB (printed Circuit Boards) and the test points. These are the points we are mean to be "jumping".
What is the sequence of events ? Do I turn off the phone first ? Do I turn on the phone while having the points jumped ?
Do I connect the phone to the computer via USB first, and then allow debugging ... and THEN jump the points with tweezers or a paperclip ?
Any ideas would be greatly appreciated.

CrotteDeChien said:
I am having trouble getting the phone into edl mode, (which I found means Extended Download Mode BTW).
Any ideas would be greatly appreciated.
Click to expand...
Click to collapse
See after Step 6., but really be careful. Good luck
https://in.c.mi.com/thread-387857-1-0.html

Entered EDL mode after tearing down my phone. Flashed the "prog_emmc_.... .mbn" and "rawprogram_000b....." files with QFil successfully. But my phone just lights up, shows Hisense logo when try to start the device. Same bricked device.
Any idea?

Mehedi34 said:
Entered EDL mode after tearing down my phone. Flashed the "prog_emmc_.... .mbn" and "rawprogram_000b....." files with QFil successfully. But my phone just lights up, shows Hisense logo when try to start the device. Same bricked device.
Any idea?
Click to expand...
Click to collapse
Dear Mehedi,
use the base firmware 6.03.02 for edl-mode flashing in Qfil provided from gowin132
https://drive.google.com/file/d/1LqcR6NVlSqL6gT6y1y1x9r58_LAKBBjd/view?usp=sharing
Then flash this in Qfil see here some general infos
https://forum.xda-developers.com/showpost.php?p=82654769&postcount=79
use "prog_emmc_firehose_8937_ddr_000bf0e1.mbn"
from the package of joygram
Flash each partition in Qfil Partition Manager (Menu Tools)
After that reboot the device and it should work.
Then upgrade to latest 6.09.06 with TFMode (microSD)
https://forum.xda-developers.com/showpost.php?p=82583733&postcount=28

see also here
https://forum.xda-developers.com/an...nfo-thread-t4101945/post82794951#post82794951

JLowe said:
see also here
https://forum.xda-developers.com/an...nfo-thread-t4101945/post82794951#post82794951
Click to expand...
Click to collapse
Successfully unbricked my phone. Thanks everyone [email protected] @joygram @gowin132

Mehedi34 said:
Successfully unbricked my phone. Thanks everyone [email protected] @joygram @gowin132
Click to expand...
Click to collapse
Good to hear that you're successful! You can't soft brick these China Qualcomm Smartphones
Have fun with this great device!

5 Methods to enter EDL mode on any Xiaomi smartphones [Qualcomm]
5 Methods to enter EDL mode on any Xiaomi smartphones [Qualcomm]
1. Boot EDL Mode via ADB Commands
2. Use Fastboot to Boot EDL mode on any Xiaomi smartphones
3. Use Hardware Buttons
===> Turn off your device.
===> Press and hold the Power + Volume Down buttons together and immediately connect the device to the PC.
===> It will automatically boot into EDL mode and LED lights may blink.
4. Use Deep Flash Cable
5. Use PCB Test Points

Well I guess I bricked my phone. I had it rooted with google play services but wanted to reset it. After a factory reset it seems like I'm stuck in a boot loop or something and also can't get into TF mode to flash the original firmware again.
I had many services disabled but nothing uninstalled before the factory reset.
Does anyone know what I can do to unbrick it or get into TF mode?

hammelgammler said:
Well I guess I bricked my phone. I had it rooted with google play services but wanted to reset it. After a factory reset it seems like I'm stuck in a boot loop or something and also can't get into TF mode to flash the original firmware again.
I had many services disabled but nothing uninstalled before the factory reset.
Does anyone know what I can do to unbrick it or get into TF mode?
Click to expand...
Click to collapse
Just follow this here
https://forum.xda-developers.com/android/general/hisense-a5-root-gapps-customizer-t4097951
joygram uploaded a new version R04 which include original Edl firmware 6.09.06. So just flash this in qfil and then reboot to system and then go into qfil for root and flash the modified partitions.
If this doesn't work you can try the old way:
Before the way was as here described you needed first to in qfil 6.03.02 then going into TF-Mode to flash actual 6.09.06, reboot to system and then again Qfil for root,...
https://forum.xda-developers.com/android/help/hisense-a5-info-thread-t4101945
Good luck!

JLowe said:
Just follow this here
https://forum.xda-developers.com/android/general/hisense-a5-root-gapps-customizer-t4097951
joygram uploaded a new version R04 which include original Edl firmware 6.09.06. So just flash this in qfil and then reboot to system and then go into qfil for root and flash the modified partitions.
If this doesn't work you can try the old way:
Before the way was as here described you needed first to in qfil 6.03.02 then going into TF-Mode to flash actual 6.09.06, reboot to system and then again Qfil for root,...
https://forum.xda-developers.com/android/help/hisense-a5-info-thread-t4101945
Good luck!
Click to expand...
Click to collapse
I made a deep flash cable myself but sadly that doesn't seem to work either. Maybe I did something wrong with the cable but it seems all good to me. I can connect another phone with it and it functions normally, so the only thing that can be defect is the switch/button itself which shorts/connects the green and black wire together.
When I plug the Hisense in my computer with the button pressed it "starts normally" into the boot loop or something and when I let go off the button nothing happens.
As far as I read, you press the button, plug the phone into the computer and after about 8 seconds or so you let go off the button and it will boot into edl mode. But it doesn't seem to work for me.
Thank you. Any help would be very appreciated.
Edit: Okay I got it. For some reason I had to press the button on the cable, volume up/down and power button together for a few seconds until it showed up i QFIL.

JLowe said:
Just follow this here
https://forum.xda-developers.com/android/general/hisense-a5-root-gapps-customizer-t4097951
joygram uploaded a new version R04 which include original Edl firmware 6.09.06. So just flash this in qfil and then reboot to system and then go into qfil for root and flash the modified partitions.
If this doesn't work you can try the old way:
Before the way was as here described you needed first to in qfil 6.03.02 then going into TF-Mode to flash actual 6.09.06, reboot to system and then again Qfil for root,...
https://forum.xda-developers.com/android/help/hisense-a5-info-thread-t4101945
Good luck!
Click to expand...
Click to collapse
Same me. I had rooted it but i tried to reflash stock firmware and now has bootloop. How imcan fix? If i flash root it will boot, but i want to go back to stock

Mehedi34 said:
I used just my fingernail. You can start opening from the weakest point which is near the sim card port.
Click to expand...
Click to collapse
I also used my fingernail too, its easy to handle,

Moto One Macro - Bricked Device

Hello folks, please help me ASAP, as I have no other devices in me and both my private and work related things are associated with my phone so...
I was doing this and since im noob I was going step by step so i dont mess something and yet that happened. you can read from there what I was doing and what happened.
Basically I tried to flash firmware by executing line by line of commands and now my phone is dark (nothing can be done with physically clicking the buttons). Its connected with the PC so sometimes i can hear that USB sounds you know.. Anyway, can you please assist me how to proceed and go back to normal ?

Open device manager and look for Qualcomm
if you see that your Device is in EDL Mode.

Try this tool
lolinet mirrors - firmware, software, iso etc.
lolinet mirrors - powered by h5ai
mirrors.lolinet.com

sd_shadow
Nope, nothing with qualcomm in my device manager.
And after running "bank-flash" my device now rebooted to fastboot.

KomitaMKD said:
sd_shadow
Nope, nothing with qualcomm in my device manager.
And after running "bank-flash" my device now rebooted to fastboot.
Click to expand...
Click to collapse
ok, I'm not sure what the flashing problem is.
rerun
Code:
fastboot getvar all

sd_shadow said:
ok, I'm not sure what the flashing problem is.
rerun
Code:
fastboot getvar all
Click to expand...
Click to collapse
I pressed the button to start the mobile and now its stuck/taking too long on the motorola logo.
running the bank flash file in this state gives me this now
Code:
working path= C:\Users\trajk\Downloads\rescuetool_JimnyPlus_64
Loading Da...
Loading Da OK!
Loading Scatter file...
ChecksumLevel = 2!
Loading Scatter file success!
Loading AuthFile...
Loading Auth OK!
Waiting for com port cable insert...
Please insert comport...

KomitaMKD said:
I pressed the button to start the mobile and now its stuck/taking too long on the motorola logo.
running the bank flash file in this state gives me this now
Code:
working path= C:\Users\trajk\Downloads\rescuetool_JimnyPlus_64
Loading Da...
Loading Da OK!
Loading Scatter file...
ChecksumLevel = 2!
Loading Scatter file success!
Loading AuthFile...
Loading Auth OK!
Waiting for com port cable insert...
Please insert comport...
Click to expand...
Click to collapse
Blankflash only works with EDL Mode (black screen)

10 minutes later im still stuck on the Motorola - Powered by Android logo

So, how do I proceed now?

Try this guide, my friend: https://forum.xda-developers.com/t/...your-bricked-motorola-moto-one-macro.4145191/

VD171 said:
Try this guide, my friend: https://forum.xda-developers.com/t/...your-bricked-motorola-moto-one-macro.4145191/
Click to expand...
Click to collapse
Im not sure how to use this
Official Stock Rom by LOLINET: https://mirrors.lolinet.com/firmware/moto/lima/official
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

KomitaMKD said:
So, how do I proceed now?
Click to expand...
Click to collapse
You need to reboot to fastboot mode, unplug USB, and hold the volume button and power, till you see the fastboot screen.

You have
Code:
ro.carrier: reteu

sd_shadow said:
You have
Code:
ro.carrier: reteu
Click to expand...
Click to collapse
Okay that did the work now my phone is off - black after i pressed the buttons...
Now which one should i download? Should i use the Android 10 one or the 9 one you mentoined previously (if its the same). btw before i do anything i had android 9 running with the november patch

I tried that Android 10 and this is what i did.
Extracted Mediatek and the firmware in same folder, did the cmd thing from the xml through the spanish web site, ran the bat file and nothing happened.
Now ill be trying with the android 9 version

Okay guys im not able to successfully run the flashfile.bat

I tried with the (Optional) Automatic BAT file made by Eufracio López and it did the trick!!! I was able to flash Android 10!

KomitaMKD said:
I tried with the (Optional) Automatic BAT file made by Eufracio López and it did the trick!!! I was able to flash Android 10!
Click to expand...
Click to collapse
Nice job, my friend.

I would like to thank you all who spared some of your
VD171 said:
Nice job, my friend.
Click to expand...
Click to collapse
Thanks to you and @sd_shadow , I really appreciate your quick assistance

KomitaMKD said:
Hello folks, please help me ASAP, as I have no other devices in me and both my private and work related things are associated with my phone so...
I was doing this and since im noob I was going step by step so i dont mess something and yet that happened. you can read from there what I was doing and what happened.
Basically I tried to flash firmware by executing line by line of commands and now my phone is dark (nothing can be done with physically clicking the buttons). Its connected with the PC so sometimes i can hear that USB sounds you know.. Anyway, can you please assist me how to proceed and go back to normal ?
Click to expand...
Click to collapse
Hi @KomitaMKD this is vignesh , i am also using Moto One Macro device , Lastweek i have thought to flash my mobile due to some reason first time my device became brick... I am not ble to do anything its come startup failure ! Message .... I felt really bad ... Then almost i tried 8 hrs continuously for recovering my phone.. finally i found it. I recovered my mobile. Below i will give a link just go through it , that will help your mobile to become normal.
[RECOVER][UNBRICK][BLANKFLASH] How unbrick your bricked Motorola Moto One Macro
This script was made by Eufracio López (yehison). Thank you very much ! 1. First, you have to download required contents: Minimal ADB and Fastboot Tool: https://androidmtk.com/download-minimal-adb-and-fastboot-tool Motorola Device Manager...
forum.xda-developers.com

Nokia 1.4 TA-1322 Help

Hello everyone, I need some help.
On november 2021 I purchased Nokia 1.4 and that day when alarm was ringing my phone screen frozen/stopped. Screen sensor and the buttons stopped was not responding. I googled immediately and found the way to turn off forzen Nokia 1.4 by pressing Wolume up + Power off buttons same time (Source: https://www.nokia.com/phones/en_int...-reboot-my-smartphone-when-its-not-responding ).
When my phone turned on again I was happy till the next restarting of my phone. My nokia get Stucked in a Reboot Loop.
Screen lights and when Android GO Logo appears it turns off again and again.
I tried to flash my phone using QFIL Tool but there was unsolved issue of Android ADB Interface driver. The QFIL Tool couldn't detected my device. Mybe it needed different keys combination when connectiong it to PC to boot.
QFIL Tool source: https://androidmtk.com/download-qualcomm-flash-image-loader-qfil
Than I unlocked bootloader using this command:
Code:
fastboot oem unlock-go
I thought it was boot or recovery fail and by the reason I downloaded the firmware from alien9firmware
Source: https://alien9firmware.com/index.php?a=downloads&b=file&id=1325
Because QFIL Tool did not work I flashed boot and recovery via ADB. I moved these two .img files to disk C and ran the following commands
Code:
fastboot devices
fastboot reboot bootloader
fastboot flash recovery c:\recovery.img
fastboot flash boot c:\boot.img
fastboot reboot bootloader
fastboot erase cache
fastboot reboot
Disconnect device
You guess what do you think guys happen
My nokia was still stucked in reboot Loop.
Than I googled smartphones with same Core Qualcome QM 215 and downloaded Nokia 8 and Nokia 6.2 TWRPs from twrp official website.
Source: https://twrp.me/Devices/Nokia/
ADB thrown me an error when I tried to flash Nokia 8 TWRP. "The file is too large and blablabla..."
Then I tried to flashed twrp-3.6.0_9-0-SLD_sprout(nokia6.2) with no errors.
I have never seen anything like that. When I press to "Power button + Volume down" buttons my phone shows the stock recovery again which has no matter.
Then I gooled so many times I and I made a decision that every smartphone with Qualcomm QM215 core has absolutely same bugs.
There are smartphones with this terrible Processor:
Smartphones with Qualcomm Snapdragon 215 processor
List of smartphones that works with Qualcomm Snapdragon 215 processor inside.
www.kimovil.com
Than I found this video. In this video he used dryer and it worked. Unfortunately I have not dryer and... It may works on our devices too, Who knows...
Than someone told me to use MiFlash tool to boot my device. I faced another problem the firmware backup was missing the boot_lock.bat file. I had to download Xiaomi Kenzo global firmware to copy and modify the .bat files to my firmware backup. That trying became my night mare. I accidently erased Bootloader.
Today I was searching how connect How to a connect phone with erased bootloader to pc and I found this:
[guide] repair hard bricked devices with deleted bootloader (sboot)
I'm writing this in android development section because this is only section for both models, i hope this is not a problem. Also i want to say thanks to sataccount from gsmhosting, he found working map at the end. This guide is for hard bricked...
forum.xda-developers.com
Than I connected my phone to pc via usb and opened Device manager. There appeared QHSUSB_BULK device missing driver.
Then I found the driver here: https://fixfirmware.com/qhsusb-bulk-driver/
At least I managed to connect my device to pc again. And now QFIL Tool detects my phone.
Problems never ends. I downloaded 5 firmwares from different websites and the emmc filefouse prog_emmc_firehose *** ddr.mbn and Rawprogram .xml files missing in all of them.
Do someone know where can I fount the emmc Firehose and Rawprogram .xml files?

Oleg69 said:
Problems never ends. I downloaded 5 firmwares from different websites and the emmc filefouse prog_emmc_firehose *** ddr.mbn and Rawprogram .xml files missing in all of them.
Do someone know where can I fount the emmc Firehose and Rawprogram .xml files?
Click to expand...
Click to collapse
Try it

optimusodd said:
Try it
Click to expand...
Click to collapse
I have downloaded the firmware but there is not prog_emmc_firehose.mbn in the archive
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Oleg69 said:
On november 2021 I purchased Nokia 1.4 and that day when alarm was ringing my phone screen frozen/stopped. Screen sensor and the buttons stopped was not responding. I googled immediately and found the way to turn off forzen Nokia 1.4 by pressing Wolume up + Power off buttons same time
Click to expand...
Click to collapse
When it's still under warranty ,why didn't you claim it ?

optimusodd said:
When it's still under warranty ,why didn't you claim it ?
Click to expand...
Click to collapse
It was gifted to me from abroad. You know...

S
Oleg69 said:
It was gifted to me from abroad. You know...O
Click to expand...
Click to collapse
So what was your end result because I'm currently in bootloop with an unlocked bootloader as well but not having much luck with many of the same avenues you spoke of.. anyone?

Absolutely no luck, you gotta take your phone to the service center or buy a new one as I did (another brand)

Absolutely not.. I refuse. If it's an android, there's a way. Thank God this is simply one of 8 phones I've currently got

Does unlocking the bootloader of this device put the device in boot loop. I want to unlock the bootloader coz I want to install custom ROM. Anyone tell me how to unlock the bootloader of this device without putting the device in boot loop.