Related
Hello,
I have phone H600 H640_77v01.01b01 replica for SGS3 (MT6577),but it is briked,when I connect it at my computer,only what can I see it is MTK USB Port (COM 28) in "Manage" ,no light,nothing else!
When I try to flash it with SP Flash tool I got some error after red line,only what can I do it is format.
What can I do to recognize it like MT65xx preloader? I need to press some buttons when I connect it to my computer?
Sorry for my little english!
are you sure this is an MT6577 based smartphone? how do you managed to brick it? flashed wrong firmware? we need some more inforamtions here. "some error" is something i cannot build onto. make a photo of the back of your device (without the battery) to identify your device. you`ll need to get a proper firmware for your device or it will be dead forever.
edit: found this software, this one MAYBE will work: http://4shared.com/file/IAkoq9Z5/
i didn`t looked into it, but is suggest you have to flash it using SP flash tool.
Hi there,
I somehow hard bricked my Jiayu F1 WCDMA smartphone (MTK6572) by flashing a wrong ROM (event though it was supposed to be good).
Now, I can connect the phone to the PC and it get's recognised (the bell rings), but I can't flash anything (nor format) through SP Flash Tool, which keeps bumping the "Enable DRAM FAILED" annoying error, no matter what ROM I'm trying to feed it.
I really could use some help, or at least getting a working scatter file, preloader, etc, just to rule out a fault on the flashed files' side.
Thanks a lot.
barbas66 said:
Hi there,
I somehow hard bricked my Jiayu F1 WCDMA smartphone (MTK6572) by flashing a wrong ROM (event though it was supposed to be good).
Now, I can connect the phone to the PC and it get's recognised (the bell rings), but I can't flash anything (nor format) through SP Flash Tool, which keeps bumping the "Enable DRAM FAILED" annoying error, no matter what ROM I'm trying to feed it.
I really could use some help, or at least getting a working scatter file, preloader, etc, just to rule out a fault on the flashed files' side.
Thanks a lot.
Click to expand...
Click to collapse
1. Uninstall all vcom,preloader and MTK drivers using USBdeview then manually install vcom drivers (you can see how to manually install MT65xx (MediaTek) USB VCOM drivers on Windows if you need help doing this)
2. Once you have vcom drivers installed, delete the SP flash tool folder then re-extract a fresh copy
3. I believe you should have go the correct backup now so go ahead and flash it using sp flash tool. you can try meta mode (flash without battery while holding volume up button) if you're still getting the error
Hello,
I have a new Lenovo A606, that came with a strange ROM (IMEI not recognized, some weird WIFI setup) from 2014. I was able to set it up and correct the problems (thanks to google), but I still had some language issues (the Lenovo Apps including dialer, contacts, sms, etc… were English only). I was able to root it fine, and no working problem.
I decided to install a clean stock ROM, ROW: the A606_USR_S036_1502271022_V3_MP_ROW that is more recent and fully supports multilanguage.
I took a PC with Windows XP, and installed the latest SP Flash Tool, following a tutorial.
I was able to install android adb drivers and the MTK driver from the ROM image. The phone was showing in the devices, then was disappearing, then showing again… I had an error, but then I tried again with the option to update the firmware, and the Flash Tool reached the end and said it flashed succesfully.
Problem: after that, the phone was totally bricked. It would not start at all. When I plug it on the PC, it shows sporadically a device called "VENDOR 0E8D - communication" that disappears very quickly. I cannot flash it again. I just lost my brand new phone…
I tried with SP Flash Tool, and Flash SPMDT, with different ROMs, CN only, ROW, different versions… But nothing. It always says that Flash failed. Even when the phone is not plugged, I have an error with Flash SPMDT, with all ROMs, saying that (1)COM ports number is repetitive or invalid, or (2) Brom and preloader have the same comport number! and it asks me to modify them in INI file or scan again. Of course, scan fails, when I plug the phone pressing vol up + vol down (only way to make the phone recognized by the computer without a battery), the progress goes to 100% then either stays stuck there, or says it failed. SP Flash Tools gives this error: 'BROM ERROR s_ft_enable_dram_fail (4032)'
I tried several drivers, to clean drivers with usbdview, I tried several versions of SP Flash Tools… I don't know what to do anymore. I hope that Lenovo has a warranty and that they could flash it back to normal.
I don't know if it is a problem accessing the META mode on the phone, or bad roms… I tried on one computer with XP, and another with Windows 8.1, and the problem is the same.
ANY HELP would be appreciated, thank you!
Hi, thank you for using XDA Assist. It sounds like you've tried everything possible. Since it sporadically shows up on your pc try a different USB cable. If that doesn't work then I think it is bricked and you'll have to check with whomever you purchased the device from to see if they can fix it.
Thread closed.
It took me days trying to make Doogee send me these files. I managed to unbrick my device with this firmware.
So I decided to post it here so anyone can unbrick ther Y100X.
It must be used with SP Flash Tool, here is the link to the thread: Flash Tool
This is the firmware :laugh: (extract with 7zip): --files removed--
For me it worked with the Format All + Download option.
-The firmware is stock and provided by Doogee. I got nothing to do with the making of the files. I also do not get paid for providing these files. I just wanna help others. -
Link sharing is on now. Sorry for forgetting about this.
thanks for el firmware, now how to get the root ... xD. My smartphone is underway yet, cost me $ 70
Root can be achieved through kingroot. But it is an app I personally hate, so I used some KingRoot to SuperSU apps and they worked,so good luck!
Many thanks for the original Firmware :highfive:
I hope there will upgrade to 5.1 or a dream.
Hello
i got trouble with that Y100X, tried to root it with KingoRoot, then i want to replace Kinguser with SuperSu, after that it ended up in Bootloop (showing DooGee logo then reboots). SP Flash Tool won't start (also tried to find Phone with adb but it always reboot to fast and don't connect)
Any thing i can do?
nickless07 said:
Hello
i got trouble with that Y100X, tried to root it with KingoRoot, then i want to replace Kinguser with SuperSu, after that it ended up in Bootloop (showing DooGee logo then reboots). SP Flash Tool won't start (also tried to find Phone with adb but it always reboot to fast and don't connect)
Any thing i can do?
Click to expand...
Click to collapse
Excuse for machine translation.
Took the information from 4pda.ru on this phone.
I quote: "Yesterday did the same thing, got the same) to the office. Site doogee rocked tools for model valencia 2. Including VCOM driver and flasher. The drivers stood on XP vlёt. Ask insertion of a cap according to the instructions of the threads about Flash Tool. Read the instructions and firmware itself took less time than the jump firmware) So do not be scared) is Ruth will not put. How then do not need to.
Briefly: 1 swing tools here https___drive.google.com/file/d/0B-eEVUUoOlT4QzZwZE54LTVFWms/edit?pli=1
2 swing firmware from the link in the header of the topic and its extract 7zip archiver;
3 Turn off the phone, connect it to a computer, manually set VCOM driver from the archive with the tools, disconnect the phone;
4 launch Flash Tool, look for a file scatter in the folder where you unzipped firmware
5 remove the checkbox PRELOADER
6 click DOWNLOAD, connect the cable to the computer off the phone and wait for the flashing 100%
7 disconnect the phone from the computer, and run the long wait until the turn
8 all
I hope that helps
ps in reference to replace ___ :// - new users can not link
ariss77 said:
Excuse for machine translation.
Took the information from 4pda.ru on this phone.
I quote: "Yesterday did the same thing, got the same) to the office. Site doogee rocked tools for model valencia 2. Including VCOM driver and flasher. The drivers stood on XP vlёt. Ask insertion of a cap according to the instructions of the threads about Flash Tool. Read the instructions and firmware itself took less time than the jump firmware) So do not be scared) is Ruth will not put. How then do not need to.
Briefly: 1 swing tools here https___drive.google.com/file/d/0B-eEVUUoOlT4QzZwZE54LTVFWms/edit?pli=1
2 swing firmware from the link in the header of the topic and its extract 7zip archiver;
3 Turn off the phone, connect it to a computer, manually set VCOM driver from the archive with the tools, disconnect the phone;
4 launch Flash Tool, look for a file scatter in the folder where you unzipped firmware
5 remove the checkbox PRELOADER
6 click DOWNLOAD, connect the cable to the computer off the phone and wait for the flashing 100%
7 disconnect the phone from the computer, and run the long wait until the turn
8 all
I hope that helps
ps in reference to replace ___ :// - new users can not link
Click to expand...
Click to collapse
SP Flashtool don't find phone. All drivers installed. Phone goes in fastboot or stock revocery only.
I wish i could get adb shell :crying:
Is there any way to flash system partition in Fastboot or sideload?
thank you
Hi brother
Thank you very much for the ROM, it help me a lot.
nickless07 said:
SP Flashtool don't find phone. All drivers installed. Phone goes in fastboot or stock revocery only.
I wish i could get adb shell :crying:
Is there any way to flash system partition in Fastboot or sideload?
Click to expand...
Click to collapse
Try to flash without the battery, rather than simply turned off the phone.
You my friend are a saviour.
Tried rooting and bricked my phone, Kingroot wouldn't work so tried the Kingo apk which bricked it.
Back to square one now so will wait for a verified root
Thanks :good::good::good::good::good::good::good:
Hi can with this repair an bootlop on the doogee nova y 100x .when i turnt off the phone ??
Sent from my Valencia2_Y100pro using XDA Free mobile app
Got my mother in law a doogee y100x. Apparently Google plus won't install on it. Did anyone face this? Is there a workaround?
Hi.
I had the bootloop problem, and I've solved with this firmware. (Many thanks TheSpecialNoob)
In order to FlashTool detects the phone, needs to be power off, without enter in FlashTool mode.
Select a scatter file, choose "Format All + Download" and press Download.
Thats all.
Custom recovery Doogee Nova Y100X
By the way, someone has managed to stick a custom recovery??? like the CWM or TWRP. If so, could you explain how you did, or upload the recovery.img file for the FlashTool?.
Thank you
zagzag99 said:
Got my mother in law a doogee y100x. Apparently Google plus won't install on it. Did anyone face this? Is there a workaround?
Click to expand...
Click to collapse
It's a problem on all Y100X devices. Doogee must have messed something up in the build.prop I hope they release an official fix.
Carliv Touch Recovery v3.3 for Doogee Nova Y100X
fanjul said:
By the way, someone has managed to stick a custom recovery??? like the CWM or TWRP. If so, could you explain how you did, or upload the recovery.img file for the FlashTool?.
Thank you
Click to expand...
Click to collapse
I auto-answer.
I found a Russian website, which explain how to install a custom recovery (Carliv Touch Recovery v3.3). :good:
I leave the link to the page. http://4pda.ru/forum/index.php?s=&showtopic=669833&view=findpost&p=42555995
If someone is not able to install it , I can try to explain it.
Also I have kept all the necessary files.
Regards
greetings from Spain
Thanks for giving us the original ROM.
I followed your steps and selecting "Format All + Download" I deleted the imeis and as I have read on the internet, also the NVRAM.
As I can do to permanently leave imeis? every time I have restored the ROM to modify and not know if I deleted more things to do a "Format ALL"
Someone I can pass the "NVRAM.bin" to upload it to my phone? Any other suggestions?
[email protected]
Regards
Yeah, I have the same problem. After restoring the stock rom, I have lost NVRAM settings.
Someone who has not restored the phone to stock, can upload the file nva.bin phone.
Thank you
revolut app is not available for custom roms...
how to completely remove twrp, custom rom and revert back to stock?
i don't have sd card.
model ver: redmi 9a M2006C3LG
people can't find simple solutions...
look https://forum.xda-developers.com/t/...-relock-the-bootloader.3876887/#post-78372719
Information is scattered all over the Internet, there is no one guide that covers everything. For example here they write that i can't use Xiaomi Flash Tool because i have mediatek cpu... i have to use sp flash tool, why there is no good guide in xda? https://androidmtk.com/use-mi-flash-pro-download-xiaomi-firmware
followed this
and my redmi 9a is now competely dead... black screen all the time... so good support, shiity sites, a lot tutorials with different files etc. so nice...
all these hardbrick methods not working because now phone is not recognized by pc, installed everything, volume+ and connecting and errors, no device in libusb - removed before.
python stuck on [2023-04-26 21:52:11.289733] Waiting for device
what to do with this phone? move to trash?
omg thank god it worked -.-
"Avoid stupid test point stuff. All you need to do is disconect the battery and reconnect it back again." - https://forum.xda-developers.com/t/...ecovery-no-fastboot-no-signs-of-life.3534512/
please good tutorial how to do that without this mediatek bypass and sp flash tool... so many bad tutorials or just give link to good guide.
i'm talking with myself
ok so i need only fastboot stock rom from https://www.getdroidtips.com/xiaomi-redmi-9a-stock-firmware-flash-file/
and flash with Mi Flash Tool. Easy, but what are that mediatek bypass tutorials, and sp flash tool so bad -.- so many brick problems.
https://www.reddit.com/r/Xiaomi/comments/pbk7fp
mar1732 said:
omg thank god it worked -.-
"Avoid stupid test point stuff. All you need to do is disconect the battery and reconnect it back again." - https://forum.xda-developers.com/t/...ecovery-no-fastboot-no-signs-of-life.3534512/
please good tutorial how to do that without this mediatek bypass and sp flash tool... so many bad tutorials or just give link to good guide.
Click to expand...
Click to collapse
Yea because you failed to flash with Sp Flash Tool
mar1732 said:
i'm talking with myself
ok so i need only fastboot stock rom from https://www.getdroidtips.com/xiaomi-redmi-9a-stock-firmware-flash-file/
and flash with Mi Flash Tool. Easy, but what are that mediatek bypass tutorials, and sp flash tool so bad -.- so many brick problems.
https://www.reddit.com/r/Xiaomi/comments/pbk7fp
Click to expand...
Click to collapse
Well, you can use MiFlashTool, create a folder named *logs*( idk if it's logs or log but try logs first) inside the MiFlashTool folder if you don't have it ( because u will see errors). Open the tool, select your rom, connect your phone in fastboot, click refresh to scan again, and click flash
P.S. If your device can boot to fastboot you can use MiFlashTool method
-----------------------------------------------------------------
My bad, I didn't read all of that.
Let's see , you need some tools, Mediatek bypass tool ( I used The app not the python one) , sp flash tool, and ... LibUsb first time, nothing else i think. Ok so :
1. Open lib usb and do your thing yk what I mean. ( Skip this if u did that )
2. Open Sp flash tool and bypass tool
3. Load your rom in sp Flash tool app, if you have blackscreen or something press firmware upgrade, if not just download, and deselect the preloader??
4. On bypass app, press bypass button, connect phone holding the volume up and power button i think, you can try another combination if it doesn't work ( try holding for ~2 seconds more after bypassing ). It should work.
5. Back to Sp Flash Tool, open settings, go to connections( idk i forgot the name, but u should , and change from USB to uport or smth, to your phone port.
6. Flash .
If you need help, just give me your discord? I don't remember all the things and yeah.....