Related
Hi,
My Honor 6 (Indian Version) was stuck in boot loop post OTA upgrade from B822 to B831. In order to fix this issue, I went through many forums available online and then decided to use the Multi Tool to downgrade to Android L & EMUI 3.1.
To get this done I have followed the below steps:
1. Unlock bootloader
2. Extract BOOT, CUST, RECOVERY and SYSTEM files from the update package downloaded from Honor.in site. //(Honor 6_Firmware_H60-L04_Android 5.1.1_EMUI 3.1_C675B570_India_Flipkart)//
3. Used Multi Tool to unbrick.
Post this the phone is not able to get into recovery mode; it's stuck at the logo screen. It doesnot recognise the 3 button command to boot into recovery mode.
I have tried using the 'boot to recovery' command in Multi Tool but it throws error "daemon not running starting on port 5037".
I have also tried adb command but for some reason my computer does not recognise my mobile.
i.e. adb devices --> doesnot show my device. (yes, I have updated the abb drivers). So I am not able to use any adb commands.
Then i tried installing/flashing CWM & TWRP recovery. None helped. :crying:
Now I am here, out of options and do not know how to proceed.
Could someone in this forum help me fix the current issue? Please.
In addition, I would like to know a few things:
a. How to install a new OS/ROM on a dead phone? (Healthy hardware with corrupt software)
b. How to format any phone and start a fresh installation?
c. How to read internal memory of a phone which has no ROM or corrupt software?
I am new to all this. Please bear with me.
Thanks,
Sampath
sampathnayak09 said:
Hi,
My Honor 6 (Indian Version) was stuck in boot loop post OTA upgrade from B822 to B831. In order to fix this issue, I went through many forums available online and then decided to use the Multi Tool to downgrade to Android L & EMUI 3.1.
To get this done I have followed the below steps:
1. Unlock bootloader
2. Extract BOOT, CUST, RECOVERY and SYSTEM files from the update package downloaded from Honor.in site. //(Honor 6_Firmware_H60-L04_Android 5.1.1_EMUI 3.1_C675B570_India_Flipkart)//
3. Used Multi Tool to unbrick.
Post this the phone is not able to get into recovery mode; it's stuck at the logo screen. It doesnot recognise the 3 button command to boot into recovery mode.
I have tried using the 'boot to recovery' command in Multi Tool but it throws error "daemon not running starting on port 5037".
I have also tried adb command but for some reason my computer does not recognise my mobile.
i.e. adb devices --> doesnot show my device. (yes, I have updated the abb drivers). So I am not able to use any adb commands.
Then i tried installing/flashing CWM & TWRP recovery. None helped. :crying:
Now I am here, out of options and do not know how to proceed.
Could someone in this forum help me fix the current issue? Please.
In addition, I would like to know a few things:
a. How to install a new OS/ROM on a dead phone? (Healthy hardware with corrupt software)
b. How to format any phone and start a fresh installation?
c. How to read internal memory of a phone which has no ROM or corrupt software?
I am new to all this. Please bear with me.
Thanks,
Sampath
Click to expand...
Click to collapse
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
How to return back to Stock Recovery & Install Stock Rom.
muradulislam said:
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
Click to expand...
Click to collapse
I am in a bit different situation, let me explain.
Till day before yesterday I was on B570 Rom, then I upgraded over OTA to B831, then Unlocked Bootloader, Rooted, Installed Latest TWRP Recovery & Installed Latest Xposed Framework, everything went successfull & My phone is running fine.
But the question that arises to me is that none of the Stock Marshmallow update for Honor 6 - H60-L04 has been stable as compared to Lollipop Version & I found B570 super stable & the possibility of myself reverting back to B570 is more. What would be the procedure to revert back to B570.. I think first of all I would have to revert back to stock recovery & then flash the rom package, but how to do this successfully.
Kindly advice.
muradulislam said:
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
Click to expand...
Click to collapse
Thank you for your response. :good:
I have flashed all the files using the fastboot mode, but my phone does not recognise the 3 button command.
It either displays the Honor logo or restarts with a quick vibration. the only command it recognised is 'Vol Down + USB plugged into a computer' (for fastboot).
When flashed with Honor Custom or CWM recovery the phone does not recognise:
1. Vol up + Vol down + Power - for recovery mode
2. Vol down + Power - for hard reset/clear cache partition
When flashed with TWRP recovery the phone only recognises: Power + Vol Up button which boots into recovery mode; however this works only when connected to a power source, the moment I disconnect the power cable the phone switches off.
I tried to install Honor 6 custom ROM EMUI4.0 using TWRP. Need guidance on the below two scenarios.
1. TWRP only recognises .zip files. HONOR custom ROMs are in .app format. What should I do?
2. As a work around, I have downloaded 'Honor 6_Firmware_H60-L04_Andriod 6.0_EMUI 4.0_C432B820_Channel-Others.zip' from xda forum and tried installing it, but TWRP throws a 'no md5 file found' error.
To address this I tried using WinMD5.exe to get the MD5 code and manually created a .MD5 file, but TWRP did not recognise it. Please guide.
Thanks,
Sampath
sampathnayak09 said:
Thank you for your response. :good:
I have flashed all the files using the fastboot mode, but my phone does not recognise the 3 button command.
It either displays the Honor logo or restarts with a quick vibration. the only command it recognised is 'Vol Down + USB plugged into a computer' (for fastboot).
When flashed with Honor Custom or CWM recovery the phone does not recognise:
1. Vol up + Vol down + Power - for recovery mode
2. Vol down + Power - for hard reset/clear cache partition
When flashed with TWRP recovery the phone only recognises: Power + Vol Up button which boots into recovery mode; however this works only when connected to a power source, the moment I disconnect the power cable the phone switches off.
I tried to install Honor 6 custom ROM EMUI4.0 using TWRP. Need guidance on the below two scenarios.
1. TWRP only recognises .zip files. HONOR custom ROMs are in .app format. What should I do?
2. As a work around, I have downloaded 'Honor 6_Firmware_H60-L04_Andriod 6.0_EMUI 4.0_C432B820_Channel-Others.zip' from xda forum and tried installing it, but TWRP throws a 'no md5 file found' error.
To address this I tried using WinMD5.exe to get the MD5 code and manually created a .MD5 file, but TWRP did not recognise it. Please guide.
Thanks,
Sampath
Click to expand...
Click to collapse
@DigiGoon
@sampathnayak09
You need to flash stock recovery first, by executing this command:
Code:
fastboot flash recovery recovery.img
@sampathnayak09
Make sure your power button is working correctly. If the files can be flashed successfully, you should be able to boot into recovery.
Honor firmware can only be flashed using three button method. You can search online for making .zip from .app but I am not sure that will solve your problem.
---------- Post added at 04:10 AM ---------- Previous post was at 04:06 AM ----------
mahadikrs said:
I am in a bit different situation, let me explain.
Till day before yesterday I was on B570 Rom, then I upgraded over OTA to B831, then Unlocked Bootloader, Rooted, Installed Latest TWRP Recovery & Installed Latest Xposed Framework, everything went successfull & My phone is running fine.
But the question that arises to me is that none of the Stock Marshmallow update for Honor 6 - H60-L04 has been stable as compared to Lollipop Version & I found B570 super stable & the possibility of myself reverting back to B570 is more. What would be the procedure to revert back to B570.. I think first of all I would have to revert back to stock recovery & then flash the rom package, but how to do this successfully.
Kindly advice.
Click to expand...
Click to collapse
There are rollback packages for going back. I have read those threads on XDA but could not find them again. Will look for them and will send you a link as soon as I found one.
muradulislam said:
@sampathnayak09
Make sure your power button is working correctly. If the files can be flashed successfully, you should be able to boot into recovery.
Honor firmware can only be flashed using three button method. You can search online for making .zip from .app but I am not sure that will solve your problem.
---------- Post added at 04:10 AM ---------- Previous post was at 04:06 AM ----------
There are rollback packages for going back. I have read those threads on XDA but could not find them again. Will look for them and will send you a link as soon as I found one.
Click to expand...
Click to collapse
Thanks for the reply.
If I extract the recovery.img from the B831 Rom Package & flash the same using the below command will it give me back my stock recovery.
fastboot flash recovery recovery.img
And if once I am on Stock Recovery I hope I can again Install a full fresh copy of the B831 Package which will be with Stock Recovery i.e NO TWRP Recovery & root free. And after that when I get the rollback package I can revert back to B570. Pls advice am I going right or is there any possibility that I will brick my phone.
sampathnayak09 said:
Thank you for your response. :good:
I have flashed all the files using the fastboot mode, but my phone does not recognise the 3 button command.
It either displays the Honor logo or restarts with a quick vibration. the only command it recognised is 'Vol Down + USB plugged into a computer' (for fastboot).
When flashed with Honor Custom or CWM recovery the phone does not recognise:
1. Vol up + Vol down + Power - for recovery mode
2. Vol down + Power - for hard reset/clear cache partition
When flashed with TWRP recovery the phone only recognises: Power + Vol Up button which boots into recovery mode; however this works only when connected to a power source, the moment I disconnect the power cable the phone switches off.
I tried to install Honor 6 custom ROM EMUI4.0 using TWRP. Need guidance on the below two scenarios.
1. TWRP only recognises .zip files. HONOR custom ROMs are in .app format. What should I do?
2. As a work around, I have downloaded 'Honor 6_Firmware_H60-L04_Andriod 6.0_EMUI 4.0_C432B820_Channel-Others.zip' from xda forum and tried installing it, but TWRP throws a 'no md5 file found' error.
To address this I tried using WinMD5.exe to get the MD5 code and manually created a .MD5 file, but TWRP did not recognise it. Please guide.
Thanks,
Sampath
Click to expand...
Click to collapse
If the phone keeps going off you tried charging for a while? Battery might not be charging due to no OS.
Sent from my H60-L04 using XDA Labs
mahadikrs said:
Thanks for the reply.
If I extract the recovery.img from the B831 Rom Package & flash the same using the below command will it give me back my stock recovery.
fastboot flash recovery recovery.img
And if once I am on Stock Recovery I hope I can again Install a full fresh copy of the B831 Package which will be with Stock Recovery i.e NO TWRP Recovery & root free. And after that when I get the rollback package I can revert back to B570. Pls advice am I going right or is there any possibility that I will brick my phone.
Click to expand...
Click to collapse
Try out this thread...
http://forum.xda-developers.com/hon...wngrade-eu-h60-l04-indian-b810-t3367031/page1
My honor 6 bricked about a month ago so can not verify this method but to get out of bootloop, always keep a nandroid backup of your device somewhere safe.
You can make a nandroid backup using twrp. Save it to SD card and then copy it to your PC to keep it safe.
muradulislam said:
Try out this thread...
http://forum.xda-developers.com/hon...wngrade-eu-h60-l04-indian-b810-t3367031/page1
My honor 6 bricked about a month ago so can not verify this method but to get out of bootloop, always keep a nandroid backup of your device somewhere safe.
You can make a nandroid backup using twrp. Save it to SD card and then copy it to your PC to keep it safe.
Click to expand...
Click to collapse
Thanks for your response.
I was able to do as per the steps I mentioned in my earlier post & now I have successfully Downgraded to B570, With Unlocked Bootloader, Rooted, TWRP & Xposed Installed. So its time for me to change my signature.
P.s : Also Updated TWRP to the Latest Version i.e TWRP 3.0.2-0
DigiGoon said:
@sampathnayak09
You need to flash stock recovery first, by executing this command:
Code:
fastboot flash recovery recovery.img
Click to expand...
Click to collapse
Hi,
I did flash the stock recovery, but my phone keeps rebooting and doesn't get into recovery mode.
I am sure it has sufficient battery charge. (Close to 90%).
Is there a way to do a clean install on Android phones? Like the way we install Windows OS on computers. Format hard disks, create partitions and then install a fresh OS?
Thanks
mahadikrs said:
Thanks for your response.
I was able to do as per the steps I mentioned in my earlier post & now I have successfully Downgraded to B570, With Unlocked Bootloader, Rooted, TWRP & Xposed Installed. So its time for me to change my signature.
P.s : Also Updated TWRP to the Latest Version i.e TWRP 3.0.2-0
Click to expand...
Click to collapse
Hi,
Could you please provide links to
1. The downgrade transition package.
2. Latest TWRP version.
Also plz help me understand the benifits of TWRP when it cannot be used to install the stock ROM?
sampathnayak09 said:
Hi,
Could you please provide links to
1. The downgrade transition package.
2. Latest TWRP version.
Also plz help me understand the benifits of TWRP when it cannot be used to install the stock ROM?
Click to expand...
Click to collapse
Find attached below the required links for Rollback package & TWRP.
1) https://club.hihonor.com/in/honor6.217/downgrade-link-from-marshmallow-b831-to-lollipop-b570.7935
2) https://twrp.me/devices/huaweihonor6.html
Regarding TWRP, it lets you install custom roms & other apps which cannot be installed thru stock recovery e.g Xposed Framework. Further TWRP is useful for restoring the phone as it allows to restore the phone by using Nandroid backups taken earlier, provided the Nandroid backups are stored in SD Card. There may be more advantages which I am still trying to find out.
mahadikrs said:
Find attached below the required links for Rollback package & TWRP.
1) https://club.hihonor.com/in/honor6.217/downgrade-link-from-marshmallow-b831-to-lollipop-b570.7935
2) https://twrp.me/devices/huaweihonor6.html
Regarding TWRP, it lets you install custom roms & other apps which cannot be installed thru stock recovery e.g Xposed Framework. Further TWRP is useful for restoring the phone as it allows to restore the phone by using Nandroid backups taken earlier, provided the Nandroid backups are stored in SD Card. There may be more advantages which I am still trying to find out.
Click to expand...
Click to collapse
Thank you for providing the links. Let me try installing these.
muradulislam said:
First of all hold and press power + vol down to boot into bootloader mode and type
Fastboot devices
After connecting your phone to PC and opening a command window in platform-tools. Your device should be listed.
adb devices works only when your phone is already booted into Android or running twrp.
Copy and paste the four image files to platform-tools folder and fire these commands
Fastboot flash boot boot.img
Fastboot flash recovery recovery.img
Fastboot flash system system.img
Fastboot flash cust cust.img
And then use the 3 button command.
(Platform-tools folder can be downloaded after installing latest Android SDK software)
Click to expand...
Click to collapse
goldfinv said:
If the phone keeps going off you tried charging for a while? Battery might not be charging due to no OS.
Sent from my H60-L04 using XDA Labs
Click to expand...
Click to collapse
Phone has 75% + charge as shown in TWRP recovery.
sampathnayak09 said:
Phone has 75% + charge as shown in TWRP recovery.
Click to expand...
Click to collapse
Maybe try flashing one of the custom EMUI ROMs via TWRP?
Sent from my H60-L04 using XDA Labs
@mahadikrs @muradulislam @goldfinv
Thank you for your input guys. I am now able to enter stock recovery mode (3 button mode); however, the installation stops at 5%.
Any suggestions?
sampathnayak09 said:
@[email protected]@goldfinv
Thank you for your input guys. I am now able to enter stock recovery mode (3 button mode); however, the installation stops at 5%.
Any suggestions?
Click to expand...
Click to collapse
Give it a couple of tries. Users have suggested that it usually gets stuck somewhere but trying for 2,3 times gets the job done.
Sent from my PLK-L01 using XDA Labs
sampathnayak09 said:
@mahadikrs @muradulislam @goldfinv
Thank you for your input guys. I am now able to enter stock recovery mode (3 button mode); however, the installation stops at 5%.
Any suggestions?
Click to expand...
Click to collapse
Let me know which Rom version is your phone running now & which version you are trying to migrate to.
Also if 3 button Force update is not working then you can try the project menu option.
But first let me know what state your phone is currently in.
The issue I am having is that my honor 8 (FRD-L14) is stuck on "your device is booting now.." and it does not shut down. If I hold the power button until it shuts down then it restarts by itself and it keep doing the same thing over and over.
When it first starts and the blue screen and the logo come up the phone vibrate twice and then it displays "your device is booting now..." and it gets stuck there
Here is what I can and cant do:
I can go into fastboot and it shows that the phone is unlocked and the FRP is unlocked
I can flash TWRP from there and I can go into TWRP
When I check in TWRP for partitions I can see CUST or DATA and it shows that the INTERNAL STORAGE size is ZERO
I was able to create the system partition but I am not sure if I did it right.
the dload folder on the SD Card has the role back but the three finger thing (vol+ and vol- and power does not start the system restore from update.app) instead it gets stuck on " your device is booting now..."
I tried Huawei_Multi-Tool and I chose the "unbrick option"...I extracted system.img, boot.img, recovery.img and cust.img and the tool was able to push all images to the device but still the device does not start.
The original stock recovery is not accessible either even if I flash the stock recovery image from TWRP
Any tips on how to resolve this?
Thanks in advance guys
fidzi_1981 said:
The issue I am having is that my honor 8 (FRD-L14) is stuck on "your device is booting now.." and it does not shut down. If I hold the power button until it shuts down then it restarts by itself and it keep doing the same thing over and over.
When it first starts and the blue screen and the logo come up the phone vibrate twice and then it displays "your device is booting now..." and it gets stuck there
Here is what I can and cant do:
I can go into fastboot and it shows that the phone is unlocked and the FRP is unlocked
I can flash TWRP from there and I can go into TWRP
When I check in TWRP for partitions I can see CUST or DATA and it shows that the INTERNAL STORAGE size is ZERO
I was able to create the system partition but I am not sure if I did it right.
the dload folder on the SD Card has the role back but the three finger thing (vol+ and vol- and power does not start the system restore from update.app) instead it gets stuck on " your device is booting now..."
I tried Huawei_Multi-Tool and I chose the "unbrick option"...I extracted system.img, boot.img, recovery.img and cust.img and the tool was able to push all images to the device but still the device does not start.
The original stock recovery is not accessible either even if I flash the stock recovery image from TWRP
Any tips on how to resolve this?
Thanks in advance guys
Click to expand...
Click to collapse
You said you can go into TWRP right. Just rebrand the device to L19 :angel:
First format data
Then flash the rebrand.zip
Then reboot and if it doesn't boot first go into recovery and factory reset then let it boot up again.
Try flashing stock recovery.img using fastboot. Can you now enter into the 3-button combination mode?
wasiq224 said:
Try flashing stock recovery.img using fastboot. Can you now enter into the 3-button combination mode?
Click to expand...
Click to collapse
He said he tried to enter recovery with no luck, and he also tried the 3 button dload method.
wasiq224 said:
Try flashing stock recovery.img using fastboot. Can you now enter into the 3-button combination mode?
Click to expand...
Click to collapse
I tried flashing the stock recovery but it does not work. I also tried the 3-buttons and it did not work either
when I go into TWRP it shows that the size of the internal storage is ZERO
damenbm said:
You said you can go into TWRP right. Just rebrand the device to L19 :angel:
First format data
Then flash the rebrand.zip
Then reboot and if it doesn't boot first go into recovery and factory reset then let it boot up again.
Click to expand...
Click to collapse
Where can I find the rebrand.zip file?
Here are the full instructions :victory:
https://forum.xda-developers.com/honor-8/how-to/guide-honor-8-to-frd-l19-t3632220
damenbm said:
Here are the full instructions :victory:
https://forum.xda-developers.com/honor-8/how-to/guide-honor-8-to-frd-l19-t3632220
Click to expand...
Click to collapse
Thanks. I will give it a try and flash it and see if it can re-create the missing partitions :fingers-crossed::fingers-crossed:
fidzi_1981 said:
Thanks. I will give it a try and flash it and see if it can re-create the missing partitions :fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
Best of luck :angel: let me know how it goes please!
damenbm said:
He said he tried to enter recovery with no luck, and he also tried the 3 button dload method.
Click to expand...
Click to collapse
Yes, but he tried the dload method before flashing stock recovery, and he was flashing stock recovery using twrp rather than fastboot.
Thanks but I tried dload after I flashed the stock recovery.
And I tried flashing the stock recovery using facebook and twrp and neither ways succeeded
fidzi_1981 said:
Thanks but I tried dload after I flashed the stock recovery.
And I tried flashing the stock recovery using facebook and twrp and neither ways succeeded
Click to expand...
Click to collapse
Did the rebrand work? Did it make you go back to stock?
damenbm said:
Did the rebrand work? Did it make you go back to stock?
Click to expand...
Click to collapse
Not yet. I'm at work. I'll give it a go tonight
For me it worked after trying to get my FRD-L09 back to work again after I couldnt flash system and not boot anywhere but twrp.
Thanks for the help!
fidzi_1981 said:
Not yet. I'm at work. I'll give it a go tonight
Click to expand...
Click to collapse
I had the same exact issue 5 days ago.
Here's what I did to solve it
NOTE - This is FRD-L14 SPECIFIC
First, Download these files -
1) FRD-L04 Original Recoveries and Boot Image
2) FRD-04 Rollback Package from Huawei
3) FRD-L04 Official MM ROM from Huawei
4) FRD-L14 Specific Stock MM ROM Update.zip
Assuming Bootloader is unlocked
Here's what you should do
-Unzip the Recoveries and Boot image folder
-Unzip Rollback Package
-Make a folder called "dload" (without the quotes) in the root of your SD Card
-Place the Update.app from the Rollback Package in there
-Make sure you have ADB and Fastboot installed - Installer
-Boot into fastboot by Plugging in your USB Cable and Holding Power + Volume Down. This may take multiple tries and multiple reboots to get it right depending on the reboot loop.
-Once phone is in Fastboot, go into the Recoveries and Boot folder, hold Shift and right Click. Click on open Command Window Here.
-If the option says "Powershell" instead, open Command prompt manually, and cd to that directory, or change this option in your settings.
-With command prompt open, do -
Code:
fastboot flash recovery recovery.img
Code:
fastboot flash recovery2 recovery2.img
Code:
fastboot flash boot boot.img
IMPORTANT - Make sure you unplug the cable from the phone and are ready to press both volume buttons at the same time after it reboots
If you dont get it the first time,hold all 3 buttons at the same time to make it reboot and go into that mode.
Code:
fastboot reboot
-Remove cable, press both Buttons at the same time
-It should go into stock recovery and start flashing the Rollback package
-Wait for it to finish, it should reboot automatically
-After it reboots, you should notice that it went back to the same state it was, so reboot into fastboot and flash recovery, recovery2, and the boot image again.
-This time, put the Update.app from the Official L04 Rom you downloaded from the Huawei website in the "dload" folder of the SDCard
-Fastboot Reboot, Remove cable, and Press buttons again. This time it will flash the Official ROM, so it will take longer.
-If it says error right at 99%, reboot, it flashed correctly but it displays an error.
-If it says error anytime before the end of flash, reboot and try again.-After it reboots, you will notice you are able to boot again. BUT, you are not able to update due to it being branded as L04, sooooo
-Place the Update.app from the 4th link (L14 Specific ROM) in the "dload" folder of SD Card
-Three button method into the recovery flash again.
-It will start to flash the L14 Specific ROM on top of the L04 one.
-After it flashes it and reboots, reboot one more time once you are inside android so it encrypts the ROM.
-(Optional) Update to Nougat, apply other updates after that (There's like 3 Updates I think)
-At this point you have a 100% Stock FRD-L14 Honor 8 but, you can also
-(Optional) Reunlock Bootloader
-Profit?
JvaOneShotzXprX said:
I had the same exact issue 5 days ago.
Here's what I did to solve it
NOTE - This is FRD-L14 SPECIFIC
First, Download these files -
1) FRD-L04 Original Recoveries and Boot Image
2) FRD-04 Rollback Package from Huawei
3) FRD-L04 Official MM ROM from Huawei
4) FRD-L14 Specific Stock MM ROM Update.zip
Assuming Bootloader is unlocked
Here's what you should do
-Unzip the Recoveries and Boot image folder
-Unzip Rollback Package
-Make a folder called "dload" (without the quotes) in the root of your SD Card
-Place the Update.app from the Rollback Package in there
-Make sure you have ADB and Fastboot installed - Installer
-Boot into fastboot by Plugging in your USB Cable and Holding Power + Volume Down. This may take multiple tries and multiple reboots to get it right depending on the reboot loop.
-Once phone is in Fastboot, go into the Recoveries and Boot folder, hold Shift and right Click. Click on open Command Window Here.
-If the option says "Powershell" instead, open Command prompt manually, and cd to that directory, or change this option in your settings.
-With command prompt open, do -
Code:
fastboot flash recovery recovery.img
Code:
fastboot flash recovery2 recovery2.img
Code:
fastboot flash boot boot.img
IMPORTANT - Make sure you unplug the cable from the phone and are ready to press both volume buttons at the same time after it reboots
If you dont get it the first time,hold all 3 buttons at the same time to make it reboot and go into that mode.
Code:
fastboot reboot
-Remove cable, press both Buttons at the same time
-It should go into stock recovery and start flashing the Rollback package
-Wait for it to finish, it should reboot automatically
-After it reboots, you should notice that it went back to the same state it was, so reboot into fastboot and flash recovery, recovery2, and the boot image again.
-This time, put the Update.app from the Official L04 Rom you downloaded from the Huawei website in the "dload" folder of the SDCard
-Fastboot Reboot, Remove cable, and Press buttons again. This time it will flash the Official ROM, so it will take longer.
-If it says error right at 99%, reboot, it flashed correctly but it displays an error.
-If it says error anytime before the end of flash, reboot and try again.-After it reboots, you will notice you are able to boot again. BUT, you are not able to update due to it being branded as L04, sooooo
-Place the Update.app from the 4th link (L14 Specific ROM) in the "dload" folder of SD Card
-Three button method into the recovery flash again.
-It will start to flash the L14 Specific ROM on top of the L04 one.
-After it flashes it and reboots, reboot one more time once you are inside android so it encrypts the ROM.
-(Optional) Update to Nougat, apply other updates after that (There's like 3 Updates I think)
-At this point you have a 100% Stock FRD-L14 Honor 8 but, you can also
-(Optional) Reunlock Bootloader
-Profit?
Click to expand...
Click to collapse
Thanks! i will give this a try since flashing the rebranding zip file that was suggested in one of the posts did not work out for me.
However, do you think that this w=method will work despite the fact that I do not have a valid DATA or CUST partitions?
Thanks again for responding to my post!!
fidzi_1981 said:
Thanks! i will give this a try since flashing the rebranding zip file that was suggested in one of the posts did not work out for me.
However, do you think that this w=method will work despite the fact that I do not have a valid DATA or CUST partitions?
Thanks again for responding to my post!!
Click to expand...
Click to collapse
No problem!
That shouldn't matter, this will get you to 100% stock, so all of those partitions will be reflashed.
JvaOneShotzXprX said:
No problem!
That shouldn't matter, this will get you to 100% stock, so all of those partitions will be reflashed.
Click to expand...
Click to collapse
It worked!!!
Thanks a lot!
but this is what happened:
After i flashed recovery, recovery2 and boot images, I rebooted the phone and it went straight to stock recovery and it asked me download stock firmware and stock recovery which was 1.66GB so I allowed and it downloaded it and flashed everything and did a reset and the phone booted normally.
The stock firmware that it downloaded and flashed was B122 MM.
One question though, does the flashing sequence of the recovery, recovery2 and boot matter?
Before you posted your post, I had tried flashing these three files in the following order: boot, then recovery then recovery2 but it never worked.
Also, the three images that tried to flash were extracted from the update.app from this firmware (FRD-L14C567B162_FULL) so I was not sure what was going wrong.
Thanks again for your help!! :victory::good::highfive:
fidzi_1981 said:
It worked!!!
Thanks a lot!
but this is what happened:
After i flashed recovery, recovery2 and boot images, I rebooted the phone and it went straight to stock recovery and it asked me download stock firmware and stock recovery which was 1.66GB so I allowed and it downloaded it and flashed everything and did a reset and the phone booted normally.
The stock firmware that it downloaded and flashed was B122 MM.
One question though, does the flashing sequence of the recovery, recovery2 and boot matter?
Before you posted your post, I had tried flashing these three files in the following order: boot, then recovery then recovery2 but it never worked.
Also, the three images that tried to flash were extracted from the update.app from this firmware (FRD-L14C567B162_FULL) so I was not sure what was going wrong.
Thanks again for your help!! :victory::good::highfive:
Click to expand...
Click to collapse
It shouldn't matter, but I included it because sometimes those get corrupted like what happened to me. I'll probably be testing it out completely and making a guide. Looks like you had it better than I did though! I'm glad you got it fixed! :highfive:
JvaOneShotzXprX said:
It shouldn't matter, but I included it because sometimes those get corrupted like what happened to me. I'll probably be testing it out completely and making a guide. Looks like you had it better than I did though! I'm glad you got it fixed! :highfive:
Click to expand...
Click to collapse
Thanks for the help again. I would not have been able to rescue the phone without your tips. :good::highfive:
I have a Honor 6x (BLN-L24) with EMUI 5+, Android Nougat, all updated. It is the U.S. edition. I unlocked the Bootloader, installed ADB / Fastboot tools and can flash the correct TWRP recovery image (3.1.1-0-berlin.img) but everytime I try to reboot into recovery, the standard EMUI recover overwrites TWRP and I just end up in the EMUI recovery.
I've looked at every forum I can find, articles, etc... but can't wrap my head around this one. If anyone with a similar experience and/or with a solution could help, I'd be most grateful.
Thank you!
I agree with with Rommco05. He IS correct, as I wondered the same thing till I realized to try unplugging it. Also make sure its the Power AND up buttons at same time. If you happen to hold only the up button it will take you to the erecovery feature where it trys hooking to WiFi for updates , which wont help you either.
Still doesn't work
Thanks for the responses. Unfortunately, unplugging doesn't do it either with the key combination you suggested. The following article is helpful for key combinations but alas, it still won't load into TWRP.
It is really strange as I can't even get past "Your device has been unlocked and can't be trusted" screen now. It just stays there...
Super frustrating. I didn't know if it had anything to do with my model being the BLN-L24 US version. I bought it at BestBuy unlocked.
Also, when I try to download "Latest Version and Recovery" from "Huawei eRecovery", I'm getting "Getting package info failed". I
Try OpenKirin twrp from recoveries section here on 6X forums
etmartinkazoo said:
Super frustrating. I didn't know if it had anything to do with my model being the BLN-L24 US version. I bought it at BestBuy unlocked.
Click to expand...
Click to collapse
That's not the cause. My phone is also a BLN-L24 purchased from Best Buy and I have no issues using TWRP. What did you do after you install TWRP? Did you let the phone just reboot or did you try to go into TWRP before rebooting?
This is straight from TWRP website:
"Note many devices will replace your custom recovery automatically during first boot. To prevent this, use Google to find the proper key combo to enter recovery. After typing fastboot reboot, hold the key combo and boot to TWRP. Once TWRP is booted, TWRP will patch the stock ROM to prevent the stock ROM from replacing TWRP. If you don't follow this step, you will have to repeat the install."
Key combination timing?
galapagos said:
That's not the cause. My phone is also a BLN-L24 purchased from Best Buy and I have no issues using TWRP. What did you do after you install TWRP? Did you let the phone just reboot or did you try to go into TWRP before rebooting?
This is straight from TWRP website:
"Note many devices will replace your custom recovery automatically during first boot. To prevent this, use Google to find the proper key combo to enter recovery. After typing fastboot reboot, hold the key combo and boot to TWRP. Once TWRP is booted, TWRP will patch the stock ROM to prevent the stock ROM from replacing TWRP. If you don't follow this step, you will have to repeat the install."
Click to expand...
Click to collapse
This is helpful, thank you. I found a page "Key Combinations Clarified for Honor 6x" which has a number of key combinations but nothing is helpful in my case that I know of. Do I use these key combinations imediately after the flash?
Is there a specific tutorial or guide that was helpful for you? I'd be grateful for any further assistance.
Thanks.
Rommco05 said:
You need enter to recovery? TWRP?
Click to expand...
Click to collapse
That is the problem, I'm unable to enter TWRP after flashing it, unplugging the usb cable, holding power/volume up...
Finally got Twrp installed. Rooted and installed custom Rom (lineageos) but when I reboot after flash screen, it's just blank...
If I were you, I would go completely back to stock and start over. Once you fastboot flash TWRP, it is imperative that you reboot back into TWRP before booting into the OS. Also, bootloaders don't overwrite recoveries. They are separate partitions, so your title is a bit misleading.
Regardless, you must still have stock recovery on your device since it is "defaulting" to that instead of TWRP. Like I said, it is extremely important to boot into recovery after you first flash it.
fastboot flash recovery recovery.img
let it do it's thing.
fastboot reboot recovery OR you can do it manually in TWRP right after the flash.
Have you tried rebooting to recovery from the system?
Connect your device to your computer, enable USB Debugging, and run
Code:
adb reboot recovery
from Windows CMD or Linux Shell, or any other one you prefer.
If this works, then you are doing the recovery key combination wrong.
Cheers
I'm having the same issue as OP. I have a BLN-L24 from Best Buy in the US. Reverted to emui 4.1 and android 6, unlocked bootloader, flashed twrp-3.2.1-0-berlin.img, and it keeps booting into huawei erecovery.
I didn't get any info on what the OP actually did to get twrp installed.
FWIW, there is no "fastboot reboot recovery"
FWIW2, you can't turn off the honor 6x from the bootloader. the best you can do is a hard reboot.
etmartinkazoo said:
That is the problem, I'm unable to enter TWRP after flashing it, unplugging the usb cable, holding power/volume up...
Click to expand...
Click to collapse
I'm having your exact same problem. I can get into fastboot mode, flash TWRP berlin, but I cannot enter TWRP after flash. It just goes back to the normal warning screen "this phone is unlocked", boot normally or go to EMUI recovery.
What worked for you?
hexag1 said:
I'm having your exact same problem. I can get into fastboot mode, flash TWRP berlin, but I cannot enter TWRP after flash. It just goes back to the normal warning screen "this phone is unlocked", boot normally or go to EMUI recovery.
What worked for you?
Click to expand...
Click to collapse
RedSkull fixed my problem!
Model: BLN L-24
I am stuck in error mode with
Func NO: 11 (recovery image)
Error NO: 2 (failed load!)
I have tried to re-flash several custom recovery I have used in the past, however none seem to work and end with the same result.
I have also tried flashing the stock recovery2.img from the Update.app for my model, but that also doesn't work and ends with a FAILED (remote: Partition Error)
I have run into troubles before, but I'm stumped with this one, I can at least still boot into fastboot.
Any help would be appreciated.
Hyperweasle said:
Model: BLN L-24
I am stuck in error mode with
Func NO: 11 (recovery image)
Error NO: 2 (failed load!)
I have tried to re-flash several custom recovery I have used in the past, however none seem to work and end with the same result.
I have also tried flashing the stock recovery2.img from the Update.app for my model, but that also doesn't work and ends with a FAILED (remote: Partition Error)
I have run into troubles before, but I'm stumped with this one, I can at least still boot into fastboot.
Any help would be appreciated.
Click to expand...
Click to collapse
What's your Android version. What were you trying to do. What recoveries have you tried and what's the command you're using. I had the same error yesterday because I flashed wrong TWRP. Fixed it by reflashing correct image.
Mannan Qamar said:
What's your Android version. What were you trying to do. What recoveries have you tried and what's the command you're using. I had the same error yesterday because I flashed wrong TWRP. Fixed it by reflashing correct image.
Click to expand...
Click to collapse
The version was Android 8 Oreo
I started out trying to go back to EMUI 8.0 from Open Kirin RROS Beta 2. So I followed this guide https://forum.xda-developers.com/honor-6x/how-to/update-bln-l22c675-emui-5-x-x-to-emui-8-t3819317
I tried the TWRP from download in the guide that was in the HWOTA8_BLN folder along with the TWRP from here https://forum.xda-developers.com/honor-6x/development/rom-emui-8-0-0-honor-6x-dual-sim-t3794079
The command I was using to flash the recoveries I believe is correct also which is the fastboot flash recovery_ramdisk "name of image" command. That command will flash successfully with the custom recoveries, however it will still bring up the error mode despite pressing +vol button.
The stock recoveries I extracted from the update.app file, I downloaded from here: https://pro-teammt.ru/firmware-database/?firmware_model=bln-L24&firmware_page=0. Which are the stock recoveries that end up with the FAILED (remote: Partition Error) Message.
Hyperweasle said:
The version was Android 8 Oreo
I started out trying to go back to EMUI 8.0 from Open Kirin RROS Beta 2. So I followed this guide https://forum.xda-developers.com/honor-6x/how-to/update-bln-l22c675-emui-5-x-x-to-emui-8-t3819317
I tried the TWRP from download in the guide that was in the HWOTA8_BLN folder along with the TWRP from here https://forum.xda-developers.com/honor-6x/development/rom-emui-8-0-0-honor-6x-dual-sim-t3794079
The command I was using to flash the recoveries I believe is correct also which is the fastboot flash recovery_ramdisk "name of image" command. That command will flash successfully with the custom recoveries, however it will still bring up the error mode despite pressing +vol button.
The stock recoveries I extracted from the update.app file, I downloaded from here: https://pro-teammt.ru/firmware-database/?firmware_model=bln-L24&firmware_page=0. Which are the stock recoveries that end up with the FAILED (remote: Partition Error) Message.
Click to expand...
Click to collapse
You tried to use HWOTA 8 to go back to stock? Dude. Use Hurupdater. Now, to fix. First of all search XDA for TWRP for hi6250. You can use Elemental but try this one first. Flash it via PowerShell. Does that give any errors? Now once it's flashed, don't reboot. Disconnect phone from PC and hold Volume Up and Power button simultaneously. You should boot into TWRP. What does bootloader say. Phone Locked or Unlocked? What about FRP? The stock recovery didn't work cause you used the BLN-L24 one which is for EMUI 5. You're on EMUI 8. Try to boot into TWRP
Mannan Qamar said:
You tried to use HWOTA 8 to go back to stock? Dude. Use Hurupdater. Now, to fix. First of all search XDA for TWRP for hi6250. You can use Elemental but try this one first. Flash it via PowerShell. Does that give any errors? Now once it's flashed, don't reboot. Disconnect phone from PC and hold Volume Up and Power button simultaneously. You should boot into TWRP. What does bootloader say. Phone Locked or Unlocked? What about FRP? The stock recovery didn't work cause you used the BLN-L24 one which is for EMUI 5. You're on EMUI 8. Try to boot into TWRP
Click to expand...
Click to collapse
https://forum.xda-developers.com/p8.../recovery-twrp-3-2-3-0-huawei-hi6250-t3859959
Ok so I flashed this one with Powershell, and it didn't show up any errors. However I still can't seem to boot into recovery and it continues to show up error mode, even while doing as you say and pressing the vol+ and power in fastboot. Also both FRP and Phone are unlocked
Hyperweasle said:
https://forum.xda-developers.com/p8.../recovery-twrp-3-2-3-0-huawei-hi6250-t3859959
Ok so I flashed this one with Powershell, and it didn't show up any errors. However I still can't seem to boot into recovery and it continues to show up error mode, even while doing as you say and pressing the vol+ and power in fastboot. Also both FRP and Phone are unlocked
Click to expand...
Click to collapse
Use Huawei multi tool 8 to unbrick your device it's easier and just use the firmware that you were in before
Hyperweasle said:
https://forum.xda-developers.com/p8.../recovery-twrp-3-2-3-0-huawei-hi6250-t3859959
Ok so I flashed this one with Powershell, and it didn't show up any errors. However I still can't seem to boot into recovery and it continues to show up error mode, even while doing as you say and pressing the vol+ and power in fastboot. Also both FRP and Phone are unlocked
Click to expand...
Click to collapse
Try Dload
hamid1999 said:
Use Huawei multi tool 8 to unbrick your device it's easier and just use the firmware that you were in before
Click to expand...
Click to collapse
Mannan Qamar said:
Try Dload
Click to expand...
Click to collapse
I tried both of those things and still couldn't get it working.
dload doesn't pop up and multi tool fails to flash the recovery_ramdisk.img when trying to unbrick it.
I do remember before any of this happened that I was having a problem with my internal storage as I didn't have access to it. All file mangers I tried couldn't access it and showed it up as blank and TWRP showed it with 0mb.
I have a feeling that my internal storage is screwed up and that's why all attempt to flash anything have failed. I may just have face the fact that it's dead.
Hyperweasle said:
I tried both of those things and still couldn't get it working.
dload doesn't pop up and multi tool fails to flash the recovery_ramdisk.img when trying to unbrick it.
I do remember before any of this happened that I was having a problem with my internal storage as I didn't have access to it. All file mangers I tried couldn't access it and showed it up as blank and TWRP showed it with 0mb.
I have a feeling that my internal storage is screwed up and that's why all attempt to flash anything have failed. I may just have face the fact that it's dead.
Click to expand...
Click to collapse
As long as it turns on it isn't dead. Did you try DC unlocker? That often works. Try it and if it fails go to service center and play dumb. Say it happened like this after a update.
Edit. Let it power off. When it turns on hold Volume Up
What I have done
I unlocked the bootloader of my Honor 6x using the testpoint method
I installed TWRP and Magisk
I decided that I was not satisfied with the stock OS and wanted to install a custom ROM
I forgot to make a backup using TWRP before flashing
I tried to flash LineageOS but it did not work and caused a bootloop (the boot animation shows for about 5 minutes and then reboots)
Using Huawei eRecovery to restore the device was not possible, and it returns the message of "Getting package info failed".
This is likely due to the website "http://update.hicloud.com/" being down
Cannot download any stock ROMs as the downloads I found are all from "http://update.hicloud.com/"
This is the only thread I found about the website being down: link
After some digging I found an old ROM (EMUI 4) that I can use, and flashed it using TWRP
The system booted up just fine after that, but the system looked really old and I wanted to update it
I found an update file and tried to install it using the dload method, which installed through the Huawei recovery just fine.
The phone rebooted and now bootloops to the Huawei eRecovery everytime.
I thought of flashing TWRP again so that maybe I can flash the old rom again, but it does not work and returns the following errors.
command: fastboot flash recovery twrp.img
error: Writing 'recovery' FAILED (remote: 'image verification error')
fastboot flash recovery_ramdisk twrp.img
error: Writing 'recovery_ramdisk' FAILED (remote: 'partition length get error')
Questions
What can I do in this situation with only have access to fastboot commands and the Huawei eRecovery?
Should I just wait for the update website to come back up so that the eRecovery will work and I can install the latest OS from there? Will that ever happen?
hey i can help ! which version of twrp are you trying to flash ?
lmaohelp said:
What I have done
I unlocked the bootloader of my Honor 6x using the testpoint method
I installed TWRP and Magisk
I decided that I was not satisfied with the stock OS and wanted to install a custom ROM
I forgot to make a backup using TWRP before flashing
I tried to flash LineageOS but it did not work and caused a bootloop (the boot animation shows for about 5 minutes and then reboots)
Using Huawei eRecovery to restore the device was not possible, and it returns the message of "Getting package info failed".
This is likely due to the website "http://update.hicloud.com/" being down
Cannot download any stock ROMs as the downloads I found are all from "http://update.hicloud.com/"
This is the only thread I found about the website being down: link
After some digging I found an old ROM (EMUI 4) that I can use, and flashed it using TWRP
The system booted up just fine after that, but the system looked really old and I wanted to update it
I found an update file and tried to install it using the dload method, which installed through the Huawei recovery just fine.
The phone rebooted and now bootloops to the Huawei eRecovery everytime.
I thought of flashing TWRP again so that maybe I can flash the old rom again, but it does not work and returns the following errors.
command: fastboot flash recovery twrp.img
error: Writing 'recovery' FAILED (remote: 'image verification error')
fastboot flash recovery_ramdisk twrp.img
error: Writing 'recovery_ramdisk' FAILED (remote: 'partition length get error')
Questions
What can I do in this situation with only have access to fastboot commands and the Huawei eRecovery?
Should I just wait for the update website to come back up so that the eRecovery will work and I can install the latest OS from there? Will that ever happen?
Click to expand...
Click to collapse
The update website isn't going to come back anytime soon. But if you just don't mind opening your device again(you need to access the test point), there's a fix. this method doesn't just need anything. even if your device is hard bricked, it can get you back running. This was described in a youtube video with working links based on a forum on xda.
link : click here
I got a similar problem recently but I flashed update.zip of emui 8 - > Bootlooped - > factory reset with twrp - > successfully booted but doesn't get past the setup screen. Fix : flashed a gsi treble image(based on android 10) - > working perfect except for camera and volte.
Venkata Lochan Nune said:
The update website isn't going to come back anytime soon. But if you just don't mind opening your device again(you need to access the test point), there's a fix. this method doesn't just need anything. even if your device is hard bricked, it can get you back running. This was described in a youtube video with working links based on a forum on xda.
link : click here
I got a similar problem recently but I flashed update.zip of emui 8 - > Bootlooped - > factory reset with twrp - > successfully booted but doesn't get past the setup screen. Fix : flashed a gsi treble image(based on android 10) - > working perfect except for camera and volte.
Click to expand...
Click to collapse
The update website is there. Its https://www.firmfinder.ml/ . No need to install any gsi
King_of_Android said:
The update website is there. Its https://www.firmfinder.ml/ . No need to install any gsi
Click to expand...
Click to collapse
My bad , I thought the update website to be huawei's official one(something like update.hicloud and all isn't it?). Well, thanks for the information but I still prefer gsi. It's buttery smooth .
And one more thing, if you follow the youtube video I mentioned, you don't need any gsi. You can get your device back on stock EMUI 5.
King_of_Android said:
hey i can help ! which version of twrp are you trying to flash ?
Click to expand...
Click to collapse
Hey I have a doubt... Will the recoveries we find in twrp official website / app work on EMUI 8? I wanted to try them but I'm afraid I might brick my device again. Getting it back is a hectic thing and I already had to face it thrice. LOL .
King_of_Android said:
The update website is there. Its https://www.firmfinder.ml/ . No need to install any gsi
Click to expand...
Click to collapse
Hi, thanks for trying to help! I am using the website to install the firmware but I am having problems with it currently, and I made a post about it, if you could help me with that it would be greatly appreciated.
lmaohelp said:
Hi, thanks for trying to help! I am using the website to install the firmware but I am having problems with it currently, and I made a post about it, if you could help me with that it would be greatly appreciated.
Click to expand...
Click to collapse
I tried using that website but I wasn't able to figure out how to use it. So just left it. Did you try the method which I described earlier?
Venkata Lochan Nune said:
I tried using that website but I wasn't able to figure out how to use it. So just left it. Did you try the method which I described earlier?
Click to expand...
Click to collapse
I haven't tried to use the method you posted yet, because it is a bit more lengthy and complicated. If the method I was using does not work I'll use the video and let you know how it goes. Thanks!
lmaohelp said:
I haven't tried to use the method you posted yet, because it is a bit more lengthy and complicated. If the method I was using does not work I'll use the video and let you know how it goes. Thanks!
Click to expand...
Click to collapse
Well, just clear these things:
Is your bootloader still unlocked?
Did you try using another recovery image instead of the one you are getting error for?
Venkata Lochan Nune said:
Well, just clear these things:
Is your bootloader still unlocked?
Did you try using another recovery image instead of the one you are getting error for?
Click to expand...
Click to collapse
My bootloader is still unlocked, yes. However, I did not try to flash another recovery image, as I was not sure where I could find one that worked. I forgot which image I used at first but it had worked the first time, so that was why I did not bother finding a different recovery. Do you have a suggestion for a recovery to install?
lmaohelp said:
My bootloader is still unlocked, yes. However, I did not try to flash another recovery image, as I was not sure where I could find one that worked. I forgot which image I used at first but it had worked the first time, so that was why I did not bother finding a different recovery. Do you have a suggestion for a recovery to install?
Click to expand...
Click to collapse
I'm attaching one that works with emui 8 try using it (Remember you have to flash it to recovery_ramdisk).
Well after reading your post 1 again, I think there's no such partition as recovery_ramdisk(because it will be there only from android 8). So find a recovery in google which works on hi6250 devices with emui 4. That should work. Update me with the result
lmaohelp said:
What I have done
I unlocked the bootloader of my Honor 6x using the testpoint method
I installed TWRP and Magisk
I decided that I was not satisfied with the stock OS and wanted to install a custom ROM
I forgot to make a backup using TWRP before flashing
I tried to flash LineageOS but it did not work and caused a bootloop (the boot animation shows for about 5 minutes and then reboots)
Using Huawei eRecovery to restore the device was not possible, and it returns the message of "Getting package info failed".
This is likely due to the website "http://update.hicloud.com/" being down
Cannot download any stock ROMs as the downloads I found are all from "http://update.hicloud.com/"
This is the only thread I found about the website being down: link
After some digging I found an old ROM (EMUI 4) that I can use, and flashed it using TWRP
The system booted up just fine after that, but the system looked really old and I wanted to update it
I found an update file and tried to install it using the dload method, which installed through the Huawei recovery just fine.
The phone rebooted and now bootloops to the Huawei eRecovery everytime.
I thought of flashing TWRP again so that maybe I can flash the old rom again, but it does not work and returns the following errors.
command: fastboot flash recovery twrp.img
error: Writing 'recovery' FAILED (remote: 'image verification error')
fastboot flash recovery_ramdisk twrp.img
error: Writing 'recovery_ramdisk' FAILED (remote: 'partition length get error')
Questions
What can I do in this situation with only have access to fastboot commands and the Huawei eRecovery?
Should I just wait for the update website to come back up so that the eRecovery will work and I can install the latest OS from there? Will that ever happen?
Click to expand...
Click to collapse
hi
can you boot into recovery (must be TWRP) at the moment? then try the following...click the link in post 3 and in youtube expand the info...then click the unbrick link and download the oeminfo.
on the phone (TWRP) recovery flash the oeminfo in to the oeminfo partion...reboot to erecovery and then download the stock rom....after this reboot into system
i had unbrick some huawei devices with this method and it helps e´very time
solong
speedson
speedson said:
hi
can you boot into recovery (must be TWRP) at the moment? then try the following...click the link in post 3 and in youtube expand the info...then click the unbrick link and download the oeminfo.
on the phone (TWRP) recovery flash the oeminfo in to the oeminfo partion...reboot to erecovery and then download the stock rom....after this reboot into system
i had unbrick some huawei devices with this method and it helps e´very time
solong
speedson
Click to expand...
Click to collapse
His problem us with twrp.
He can only access fastboot but isn't able to flash twrp...
Venkata Lochan Nune said:
Well after reading your post 1 again, I think there's no such partition as recovery_ramdisk(because it will be there only from android 8). So find a recovery in google which works on hi6250 devices with emui 4. That should work. Update me with the result
Click to expand...
Click to collapse
So I have tried many different recoveries, such as ones for EMUI 4 and 5 and flashing directly to recovery, which gave me an error "image verification failed", and flashing an EMUI 8 to ramdisk would give me the same error as before. I think the partitions on this device is really messed up lol. Also, when I type fastboot reboot recovery, it would just get stuck at the loading screen, so does that mean there is no working recovery installed?
lmaohelp said:
So I have tried many different recoveries, such as ones for EMUI 4 and 5 and flashing directly to recovery, which gave me an error "image verification failed", and flashing an EMUI 8 to ramdisk would give me the same error as before. I think the partitions on this device is really messed up lol. Also, when I type fastboot reboot recovery, it would just get stuck at the loading screen, so does that mean there is no working recovery installed?
Click to expand...
Click to collapse
Maybe yes. Did you try directly booting the image without flashing?
Code:
fastboot boot recovery.img
Venkata Lochan Nune said:
Maybe yes. Did you try directly booting the image without flashing?
Code:
fastboot boot recovery.img
Click to expand...
Click to collapse
Yup, I tried that as well, and it told me "invalid command"
lmaohelp said:
Yup, I tried that as well, and it told me "invalid command"
Click to expand...
Click to collapse
Well as you said, you partitions must have been really messed up. I have no other ideas except the test point method.
Are you trying anything else?
Ok we have some option that could help you...
Im read in the 4PDA (the russian XDA xD) forum that it should be possible to flash the oeminfo by fastboot command. So just download the HWOTA_BLN_Eng and expand it. Then go to 7 or 8 Folder and there you go to oeminfo folder. There you choose the right one for your Device and local area...for example BLN-L21 (Device) C432 (European Area)
Extract the file to your desktop and rename it to BLN-L21C432.img
--->be sure that you have the right Device driver installed and the right ADB driver for your device to<---
ok now Copy and Paste the BLN-L21C432.img to ADB folder and start command with admin rights
start the phone into fastboot mode
--->bootloader must be unlocked<---
in the command
fastboot flash oeminfo BLN-L21C432.img
wait for the result and it can not hurt to pray a bit in this moment...hihi
if this have success...you type in command
fastboot reboot
wait to the screen you can press 3 seconds Vol+ to go into erecovery....connect to wlan and it should work step by step like it should.
after download and recover the stock rom reboot and go again to erecover by press Vol+ for 3 seconds and now go to the second option...wipe data/factory reset and write yes+enter
in stock recovery wipe Data after that wipe Cache...reboot and wait that system boot the initial boot for first setup.
If this will not working...tell me what honor 6x you have and wich local area you are from and wich firmware you stock had before you doing wronng
good luck bro
solong
speedson