Requirements :
ADB Drivers
Fastboot
Moto G Stock Firmware
Downlaods :
ADB & Fastboot Setup - https://drive.google.com/file/d/0BxE4PACUiwQqVkxCOTJBZ29WNnc/view?usp=sharing
Unbrick Zip - https://drive.google.com/file/d/0BxE4PACUiwQqN0xvOGpJMUg5MVU/view?usp=sharing
CWM Touch Recovery - https://drive.google.com/file/d/0BxE4PACUiwQqbXFpU25Eb3lIWkE/view?usp=sharing
PAC-MAN ROM with GApps - http://forum.xda-developers.com/showthread.php?t=2667834
Credits : Firmware Team
CWM
Carlos Spitzer
If your phone doesn't turn on after the battery dies, then keep the power button pressed till you see the battery icon. Always connect to a wall charger if the battery is dead after the phone is hard bricked.
Method :
To Enter Fastboot :
1) When your phone is turned off, press the power key and volume down button for around 5-10 seconds and let it go.
2) Connect your phone to your pc via usb.
3) Install the setup provided in the link and press "y" in the window.
To Flash Firmware :
3) Extract the zip which contains a batch file "unbrick.bat", 5.0.2 Firmware & Fastboot.
4) Run the batch file "unbrick.bat"
If your phone is still stuck in a bootloop, I would recommend you to first flash the CWM Recovery using fastboot.
Then, you can sideload a ROM (I used PAC-MAN) using ADB. Then just flash the ROM in CWM. If you need stock, then follow the above steps after successfully booting into PAC-MAN ROM. I have provided all the links above.
That's it, you are done!
The Only Worked Tutorial
this is the only worked tutorial for me. i have tried many tutorials it seems not workin at all.luvd it:good:
I'm glad it worked
Sent from my XT1033 using XDA Free mobile app
Major problems with my XT1033
Hello, please help. I have tried to follow your instructions to unbrick my Moto G XT1033 but I just get the message in the Command Prompt that fastboot is not recognised.
I think my phone was accidently disconnected from the pc when I was trying to flash back to stock firmware from CM11. Since then the phone will not shut down & only shows 0% battery when connected to the mains. It only charges the battery when connected to the PC. I can get to the fastboot screen (please see attached images) & as can be seen the phone confirms usb is connected but the phone is not recognised by the PC. Please help. I have tried all other methods without any success.
Regards
Brian
You did it for me
:good:
Eventually I managed to get fastboot recognised & followed your instructions even though the first few commands seemed to FAIL I continued and I now have a fully working Moto G XT1033
THANK YOU
THANK YOU
THANK YOU
YOU ARE THE BEST. I SHOULD HAVE TRIED YOUR INSTRUCTIONS FIRST BECAUSE I WAS SO DISAPPOINTED I COULDN'T UNBRICK MY MOTO G I BOUGHT A 2ND GEN MOTO G.
Kind Regards
Brian
I need a help, I am using PA and I can't get gps lock.
could anybody upload/send me NON-HLOS.bin from 4.4.4 stock image?
I lived in third world country so...... it will be a pain in the a** to download the full stock image.
edit: Got it
bfc9999 said:
:good:
Eventually I managed to get fastboot recognised & followed your instructions even though the first few commands seemed to FAIL I continued and I now have a fully working Moto G XT1033
THANK YOU
THANK YOU
THANK YOU
YOU ARE THE BEST. I SHOULD HAVE TRIED YOUR INSTRUCTIONS FIRST BECAUSE I WAS SO DISAPPOINTED I COULDN'T UNBRICK MY MOTO G I BOUGHT A 2ND GEN MOTO G.
Kind Regards
Brian
Click to expand...
Click to collapse
Never lose hope
Great Tutorial. But I had Network issue and that's why i flashed it.
It was not fixed.
But reset works fine.
Clicked Thanks
please help
:crying::crying::crying::crying::crying::crying::crying::crying:
preflash validation failed....please help....ive followed the tutorial correctly but i still end up in a bootloop.........u r my only hope
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>fastboot flash partition gpt.bin
target reported max download size of 536870912 bytes
sending 'partition' (32 KB)...
OKAY [ 0.016s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.297s
C:\Users\DRAVYA\Desktop\stock>fastboot flash motoboot motoboot.img
target reported max download size of 536870912 bytes
sending 'motoboot' (1940 KB)...
OKAY [ 0.094s]
writing 'motoboot'...
(bootloader) Motoboot: Preflash validation for tz
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.359s
C:\Users\DRAVYA\Desktop\stock>fastboot flash logo logo.bin
target reported max download size of 536870912 bytes
sending 'logo' (619 KB)...
OKAY [ 0.063s]
writing 'logo'...
OKAY [ 0.031s]
finished. total time: 0.094s
C:\Users\DRAVYA\Desktop\stock>fastboot flash boot boot.img
target reported max download size of 536870912 bytes
sending 'boot' (10240 KB)...
OKAY [ 0.379s]
writing 'boot'...
OKAY [ 0.666s]
finished. total time: 1.045s
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>fastboot flash recovery recovery.img
target reported max download size of 536870912 bytes
sending 'recovery' (10240 KB)...
OKAY [ 0.378s]
writing 'recovery'...
OKAY [ 0.618s]
finished. total time: 0.996s
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>fastboot flash system system.img_sparsechunk.0
target reported max download size of 536870912 bytes
erasing 'system'...
(bootloader) Erase allowed in unlocked state
OKAY [ 0.031s]
sending 'system' (262142 KB)...
OKAY [ 8.476s]
writing 'system'...
OKAY [ 8.609s]
finished. total time: 17.117s
C:\Users\DRAVYA\Desktop\stock>fastboot flash system system.img_sparsechunk.1
target reported max download size of 536870912 bytes
erasing 'system'...
(bootloader) Erase allowed in unlocked state
OKAY [ 0.047s]
sending 'system' (237949 KB)...
OKAY [ 7.706s]
writing 'system'...
OKAY [ 7.076s]
finished. total time: 14.829s
C:\Users\DRAVYA\Desktop\stock>fastboot flash system system.img_sparsechunk.2
target reported max download size of 536870912 bytes
erasing 'system'...
(bootloader) Erase allowed in unlocked state
OKAY [ 0.047s]
sending 'system' (243326 KB)...
OKAY [ 7.856s]
writing 'system'...
OKAY [ 16.026s]
finished. total time: 23.929s
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>fastboot flash modem NON-HLOS.bin
target reported max download size of 536870912 bytes
sending 'modem' (47476 KB)...
OKAY [ 1.584s]
writing 'modem'...
OKAY [ 0.772s]
finished. total time: 2.356s
C:\Users\DRAVYA\Desktop\stock>fastboot erase modemst1
erasing 'modemst1'...
OKAY [ 0.047s]
finished. total time: 0.063s
C:\Users\DRAVYA\Desktop\stock>fastboot erase modemst2
erasing 'modemst2'...
OKAY [ 0.047s]
finished. total time: 0.063s
C:\Users\DRAVYA\Desktop\stock>fastboot flash fsg fsg.mbn
target reported max download size of 536870912 bytes
sending 'fsg' (102 KB)...
OKAY [ 0.047s]
writing 'fsg'...
OKAY [ 3.179s]
finished. total time: 3.242s
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>fastboot erase cache
******** Did you mean to fastboot format this partition?
erasing 'cache'...
OKAY [ 0.047s]
finished. total time: 0.047s
C:\Users\DRAVYA\Desktop\stock>fastboot erase userdata
erasing 'userdata'...
OKAY [ 0.063s]
finished. total time: 0.063s
C:\Users\DRAVYA\Desktop\stock>echo
ECHO is on.
C:\Users\DRAVYA\Desktop\stock>fastboot reboot
rebooting...
finished. total time: -0.000s
C:\Users\DRAVYA\Desktop\stock>
facing a problem ....please help
D:\Moto G\failsafe>fastboot flash partition gpt.bin
target reported max download size of 536870912 bytes
sending 'partition' (32 KB)...
OKAY [ 0.031s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.328s
I'm updating this thread with Lollipop 5.0.2 firmware and a batch file.
I have made changes to OP to include Lollipop Firmware and to make it easier. Hope it solves your issue.
my phone's dead
no bootloader,
no logo,
nothing
Hi I'm tryin to follow this thread after the other unbrick and restore posts didn't help.
Moto G XT1033 booting to the android logo with a traingle on top of it. Recovery doesn't work and the adb window states waiting for device although I have tried many adb drivers along with moto drivers and mfast and rdlite among other things.
Win 10, Unlocked bootloaded with no recovery and no USB debugging enabled.
Any help would e highly appreciated
C:\Program Files\Minimal ADB and Fastboot>fastboot getvar all
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
(bootloader) version: 0.5
(bootloader) version-bootloader: 411A
(bootloader) product: falcon
(bootloader) secure: yes
(bootloader) hwrev: 0x83C0
(bootloader) radio: 0x5
(bootloader) emmc: 16GB Toshiba REV=06 PRV=01 TYPE=17
(bootloader) ram: 1024MB Samsung S4 SDRAM DIE=4Gb
(bootloader) cpu: MSM8226 CS
(bootloader) serialno: TA93301I18
(bootloader) cid: 0x0007
(bootloader) channelid: 0x00
(bootloader) uid: EA25A8020F000000000000000000
(bootloader) unlocked: yes
(bootloader) iswarrantyvoid: yes
(bootloader) mot_sst: 3
(bootloader) max-download-size: 536870912
(bootloader) reason: Volume down key pressed
(bootloader) imei:
(bootloader) meid:
(bootloader) date:
(bootloader) sku:
(bootloader) iccid:
(bootloader) cust_md5:
(bootloader) max-sparse-size: 268435456
(bootloader) current-time: "Wed Apr 1 0:38:33 UTC 1959"
(bootloader) ro.build.fingerprint[0]: motorola/falcon_asia_ds/falcon_umt
(bootloader) ro.build.fingerprint[1]: sds:5.1/LPB23.13-56/55:user/releas
(bootloader) ro.build.fingerprint[2]: e-keys
(bootloader) ro.build.version.full[0]: Blur_Version.221.21.56.falcon_umt
(bootloader) ro.build.version.full[1]: sds.AsiaRetail.en.03
(bootloader) ro.build.version.qcom[0]: AU_LINUX_ANDROID_LNX.LA.3.5.1_RB1
(bootloader) ro.build.version.qcom[1]: .04.04.02.048.045
(bootloader) version-baseband: MSM8626BP_1032.3116.98.00R EMEA_DSDS_CUST
(bootloader) kernel.version[0]: Linux version 3.4.42-g89906d6 ([email protected]
(bootloader) kernel.version[1]: ilclbld32) (gcc version 4.8 (GCC) ) #1 S
(bootloader) kernel.version[2]: MP PREEMPT Mon Aug 17 10:37:16 CDT 2015
(bootloader) sdi.git: git=MBM-NG-V41.1A-0-gdc5aeaf
(bootloader) sbl1.git: git=MBM-NG-V41.1A-0-g199f3c5
(bootloader) rpm.git: git=MBM-NG-V41.1A-0-g8b7736e
(bootloader) tz.git: git=MBM-NG-V41.1A-0-g99c1a7c
(bootloader) aboot.git: git=MBM-NG-V41.1A-0-g80481ae
(bootloader) qe: qe 0/1
(bootloader) ro.carrier: unknown
all: listed above
finished. total time: 0.316s
C:\Program Files\Minimal ADB and Fastboot>
---------- Post added at 04:28 PM ---------- Previous post was at 04:27 PM ----------
my device only stuck motorola bootloader unlock
Hey
Hi Folks,
Model :- Motorola XT1033, Asia Retail.
Firmware :- Stock android 5.0.2.
My phone has been soft bricked after a reboot. I am just able to enter into fastboot mode and recovery mode.
I have tried with :-
===============
--> Installing TWRP recovery image and followed following steps. But after reboot it is not entering into TWRP recovery.
SHAVARSH-M-X1SR:Fastboot shavarsh$ fastboot flash recovery twrp-3.0.2-1-falcon.img
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
(bootloader) has-slot:recovery: not found
target reported max download size of 536870912 bytes
sending 'recovery' (9522 KB)...
OKAY [ 0.332s]
writing 'recovery'...
OKAY [ 0.172s]
finished. total time: 0.504s
SHAVARSH-M-X1SR:Fastboot shavarsh$ fastboot reboot
(bootloader) slot-count: not found
(bootloader) slot-suffixes: not found
(bootloader) slot-suffixes: not found
rebooting...
--> I tried with going into recovery from fastboot and tried to use adb sideload to install some custom ROM but it is showing "siganture verification failed".
--> I tried with solution given at this link.
http://forum.xda-developers.com/showthread.php?t=2700502
I am facing following issue.
Z:\Documents\softwares\windows\Fastboot>mfastboot.exe flash partition gpt.bin
target max-sparse-size: 256MB
sending 'partition' (32 KB)...
OKAY [ 0.037s]
writing 'partition'...
(bootloader) Preflash validation failed
FAILED (remote failure)
finished. total time: 0.197s
Z:\Documents\softwares\windows\Fastboot>
Please help me to recover my device.
Thanks and regards
Shashank
Hi there and welcome to assist,
Here is all you need for unbrick your device:
[HOW TO] Unbrick Moto G 2013! [Falcon, Peregrine] [Lollipop guide]
[HOW TO] Unbrick hard bricked Moto G (for Android 4.4.4 (5.x now available))
You'll have to create an account to post in the main forums if you have any other questions.
> Moto G > Moto G Q&A, Help & Troubleshooting
Good luck
Hi, I have been testing the SafetyNet api and I made a serious mistake, I decided to close the bootloader of my Moto Maxx, but I did not take into consideration that although I had the last published rom of my region installed, I did install an update via OTA, which I understand prevents me from installing the rom I have, since it seeks to install the rom + update, even worse, forget to click on the option "allow oem unlock" so I can not reopen the bootloader, the last rom published for my region is the XT1225_QUARK_RETLA_6.0.1_MPGS24.107-70.2-2_cid12_subsidy-DEFAULT_CFC.xml, but it does not let me flash it, I have tried all published so far, but I have only been partially lucky with the rom QUARK_VERIZON_6.0.1_MCG24 .251-5-5_cid2_subsidy-DEFAULT_CFC.xml, which I believe already comes with the security OTA update and lets me flash gpt.bin, but since it is from another region it does not let me flash recovery or system.img, will there be someone who have the last Latin American rom or at least the recovery.img to try to revive my smartphone?, sorry for my clumsy English and thanks in advance.
Well, I finally found a ROM that fix my error, if someone else goes through the same thing you can download it in
http://ftpeil.eil.com.br/vip/motoro...S24.107-70.2-7_cid12_subsidy-DEFAULT_CFC.xml/
terenos said:
Well, I finally found a ROM that fix my error, if someone else goes through the same thing you can download it in
QUARK_RETBR_6.0.1_MPGS24.107-70.2-7_cid12_subsidy-DEFAULT_CFC.xml
http://ftpeil.eil.com.br/vip/motoro...S24.107-70.2-7_cid12_subsidy-DEFAULT_CFC.xml/
Click to expand...
Click to collapse
I could have pointed you to this version by @bhb27 here:
XT1225_QUARK_RETBR_6.0.1_MPGS24.107-70.2-2_cid12_subsidy-DEFAULT_CFC.xml.zip
https://www.androidfilehost.com/?fid=385035244224403573
Fast download. But I thought you wanted RETLA version.
Looking again, the one you found may be slightly newer than what @bhb27 has posted? @bhb27, is that one he found newer?
70.2-7 (his) vs 70.2-2. (yours)
See the difference?
BUILD REQUEST INFO:
SW Version: quark_retbr-user 6.0.1 MPGS24.107-70.2-7 7 release-keysMDM9625_104438.245.02.85R
MBM Version: 70.96
Modem Version: MDM9625_104438.245.02.85R
FSG Version: UNKNOWN
Build Fingerprint: motorola/quark_retbr/quark_umts:6.0.1/MPGS24.107-70.2-7/7:user/release-keys
VERSION INFO FOUND UNDER 'ABOUT PHONE' SCREEN:
System Version: 24.211.7.quark_retbr.retbr.en.BR
Model number: Moto Maxx
Android Version: 6.0.1
Baseband Version: MDM9625_104438.245.02.85R
Build Number: MPGS24.107-70.2-7
Build Date: Tue Jan 17 04:30:18 CST 2017
OTHER MISC VERSION INFO:
Subsidy Lock Config: slcf_rev_b_default_v1.0.nvm
Regulatory Info (eLabel): None
Blur Version: Blur_Version.24.211.7.quark_retbr.retbr.en.BR
Version when read from CPV: quark_retbr-user 6.0.1 MPGS24.107-70.2-7 7 release-keys
Click to expand...
Click to collapse
ChazzMatt said:
I could have pointed you to this version by @bhb27 here:
XT1225_QUARK_RETBR_6.0.1_MPGS24.107-70.2-2_cid12_subsidy-DEFAULT_CFC.xml.zip
https://www.androidfilehost.com/?fid=385035244224403573
Fast download. But I thought you wanted RETLA version.
Looking again, the one you found may be slightly newer than what @bhb27 has posted? @bhb27, is that one he found newer?
70.2-7 (his) vs 70.2-2. (yours)
See the difference?
Click to expand...
Click to collapse
Sorry for that, I thought I needed the specific ROM of my region, but finally it was not like that, anyway thank you very much.
On the other hand, it seems that the version I found is a bit newer.
terenos said:
Well, I finally found a ROM that fix my error, if someone else goes through the same thing you can download it in
http://ftpeil.eil.com.br/vip/motoro...S24.107-70.2-7_cid12_subsidy-DEFAULT_CFC.xml/
Click to expand...
Click to collapse
Thanks. Same Here. Flash with RSD Lite and all OK. Thanks!!!
I flashed the full stock rom with RSD Lite and relock the bootloader, but the message warning bootloader unlocked already shows... Please, How to remove this message?
MelquiXDA said:
I flashed the full stock rom with RSD Lite and relock the bootloader, but the message warning bootloader unlocked already shows... Please, How to remove this message?
Click to expand...
Click to collapse
Not sure why you relocked your bootloader when you can use Magisk to hide that.
But it's easy to replace the unlocked bootloader warning. How do you want to do it -- via ADB (fastboot) or TWRP? Besides which method, choose which boot logo below you wish to replace the warning? The warning is just a graphic, and you will replace it with another graphic -- like one of the Motorola logos below.
Here's some custom boot logos from my Moto Maxx/Moto Turbo guide. Works on all Quarks -- Droid Turbo/Moto Turbo/Moto Maxx. Your choice of colors of the Motorola M logo. Very classy.
Install either via ADB (fastboot) or TWRP. Both choices are offered.
____________
BOOT LOGOS
You can just reflash your choice of boot logo to replace the unlocked warning screen. It's just a static image Motorola insists on showing you that your bootloader is unlocked.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I know, I UNLOCKED it on purpose!
Here's boot logos (not to be confused with boot animation -- the boot logo is what you see before the boot animation starts) you can flash with ADB. Various colors of the Motorola M logo.
Remove annoying bootloader unlocked warning
* ADB FLASHABLE BOOT LOGOS
http://forum.xda-developers.com/showpost.php?p=68538894&postcount=2
And here's the same boot logos you can flash with TWRP:
* TWRP FLASHABLE BOOT LOGOS
http://forum.xda-developers.com/showpost.php?p=68579272&postcount=5
Works for all Quarks (XT1254/XT1250/XT1225).
* Black and White
* Black and Teal
*White and Teal
* Black and Red
(The last three with color are custom graphics made by @fenix3nk0r3 .
* added another boot logo to my Quark guide... posts #2 (ABD) and post #5 (TWRP flashable) to include Dark Google ATAP:
Thanks to @XDleader555 for the splash logo I found in Moto X Pure forum -- but I adapted it for our Quarks so it would not be upside down. The other bundled elements are taken from the Black & Teal boot logo file ("recovery", "bootloader", etc) but the splash screen is this black artistic Motorola logo. For the TWRP flashable file I utilized @bhb27's excellent logo flasher app. Post #3 is ADB, post #5 is TWRP flashable.
ChazzMatt said:
Not sure why you relocked your bootloader when you can use Magisk to hide that.
But it's easy to replace the unlocked bootloader warning. How do you want to do it -- via ADB (fastboot) or TWRP? Besides which method, choose which boot logo below you wish to replace the warning? The warning is just a graphic, and you will replace it with another graphic -- like one of the Motorola logos below.
Here's some custom boot logos from my Moto Maxx/Moto Turbo guide. Works on all Quarks -- Droid Turbo/Moto Turbo/Moto Maxx. Your choice of colors of the Motorola M logo. Very classy.
Install either via ADB (fastboot) or TWRP. Both choices are offered.
____________
BOOT LOGOS
You can just reflash your choice of boot logo to replace the unlocked warning screen. It's just a static image Motorola insists on showing you that your bootloader is unlocked.
I know, I UNLOCKED it on purpose!
Here's boot logos (not to be confused with boot animation -- the boot logo is what you see before the boot animation starts) you can flash with ADB. Various colors of the Motorola M logo.
Remove annoying bootloader unlocked warning
* ADB FLASHABLE BOOT LOGOS
http://forum.xda-developers.com/showpost.php?p=68538894&postcount=2
And here's the same boot logos you can flash with TWRP:
* TWRP FLASHABLE BOOT LOGOS
http://forum.xda-developers.com/showpost.php?p=68579272&postcount=5
Works for all Quarks (XT1254/XT1250/XT1225).
* Black and White
* Black and Teal
*White and Teal
* Black and Red
(The last three with color are custom graphics made by @fenix3nk0r3 .
* added another boot logo to my Quark guide... posts #2 (ABD) and post #5 (TWRP flashable) to include Dark Google ATAP:
Thanks to @XDleader555 for the splash logo I found in Moto X Pure forum -- but I adapted it for our Quarks so it would not be upside down. The other bundled elements are taken from the Black & Teal boot logo file ("recovery", "bootloader", etc) but the splash screen is this black artistic Motorola logo. For the TWRP flashable file I utilized @bhb27's excellent logo flasher app. Post #3 is ADB, post #5 is TWRP flashable.
Click to expand...
Click to collapse
Thanks. I flashed the logo.bin with locked bootloader sussessfully.
I used the 01 file of this site:
https://maxximizar.wordpress.com/2016/06/24/logos-moto-maxx-droid-turbo-moto-x-style/
MelquiXDA said:
Thanks. I flashed the logo.bin with locked bootloader sussessfully.
I used the 01 file of this site:
https://maxximizar.wordpress.com/2016/06/24/logos-moto-maxx-droid-turbo-moto-x-style/
Click to expand...
Click to collapse
OK. That's very close to the White/Teal above - just a lighter shade of teal.
terenos said:
Well, I finally found a ROM that fix my error, if someone else goes through the same thing you can download it in
http://ftpeil.eil.com.br/vip/motoro...S24.107-70.2-7_cid12_subsidy-DEFAULT_CFC.xml/
Click to expand...
Click to collapse
Sorry to bump the thread. Someone have a mirror to this version?
I made the same mistake and now I need a 23.107-70.2-7 image.
Regards
I have Indian moto turbo xt1225. Till now I am using different Rom after boot loader unlocked lastyear. Last week I have planned to sell my phone. so I decided to relock boot loader. So I put command OEM lock in fast boot and bootloader got locked. The sad thing that I have forgotten to tick allow OEM unlock in developer option before doing this. Now my phone is bricked and bootloader is in locked condition. I can't push any Rom or recovery via adb or fast boot because of locked bootloader. I googled how to unlock bootloader in fast boot mode, but no solution is seen. Sombody says flashing factory firmfare via rsd lite solve the problems as it doesn't need uncloked bootloader. But when I flashing mtoturbo lollipop Indian factory version given in this forum, flashing failed message came in rds lite .flashing failed boot.img like errors. Kindly help
sreenash said:
I have Indian moto turbo xt1225. Till now I am using different Rom after boot loader unlocked lastyear. Last week I have planned to sell my phone. so I decided to relock boot loader. So I put command OEM lock in fast boot and bootloader got locked. The sad thing that I have forgotten to tick allow OEM unlock in developer option before doing this. Now my phone is bricked and bootloader is in locked condition. I can't push any Rom or recovery via adb or fast boot because of locked bootloader. I googled how to unlock bootloader in fast boot mode, but no solution is seen. Sombody says flashing factory firmfare via rsd lite solve the problems as it doesn't need uncloked bootloader. But when I flashing mtoturbo lollipop Indian factory version given in this forum, flashing failed message came in rds lite .flashing failed boot.img like errors. Kindly help
Click to expand...
Click to collapse
Searching in the web i found the latest firmware for xt1225 (is retbr, but its ok for india and other LA moto):
https://drive.google.com/file/d/1slulWTBMw833L30PMbVEFKf6XRoJuLQK/view?usp=sharing
if you need the mfastboot and "automated" flash, here is the folder i used:
https://drive.google.com/file/d/1-KrMlXplGWzMx7BWutXePNxqRmOQip50/view?usp=sharing
I hope it helps you.
Pls see the flash screen. It didnt work for me
C:\ADB>echo off max-sparse-size: 268435456 finished. total time: 0.000s target max-sparse-size: 256MB sending 'partition' (32 KB)... OKAY [ 0.016s] writing 'partition'... (bootloader) This may take a few seconds, if a (bootloader) different partition table is being (bootloader) flashed since we need to backup (bootloader) and restore a few partitions (bootloader) Flashing primary GPT image... (bootloader) Flashing backup GPT image... OKAY [ 0.172s] finished. total time: 0.187s target max-sparse-size: 256MB sending 'motoboot' (2163 KB)... OKAY [ 0.078s] writing 'motoboot'... (bootloader) flashing sbl1 ... (bootloader) flashing aboot ... (bootloader) flashing tz ... (bootloader) flashing sdi ... (bootloader) flashing rpm ... OKAY [ 0.452s] finished. total time: 0.530s target max-sparse-size: 256MB sending 'radio' (85620 KB)... OKAY [ 2.777s] writing 'radio'... (bootloader) flashing modem ... (bootloader) flashing mdm1m9kefs1 ... (bootloader) flashing mdm1m9kefs2 ... (bootloader) flashing mdm1m9kefs3 ... OKAY [ 1.420s] finished. total time: 4.196s target max-sparse-size: 256MB sending 'logo' (2712 KB)... OKAY [ 0.094s] writing 'logo'... OKAY [ 0.062s] finished. total time: 0.156s target max-sparse-size: 256MB sending 'boot' (16384 KB)... OKAY [ 0.515s] writing 'boot'... (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 0.811s target max-sparse-size: 256MB sending 'recovery' (16400 KB)... OKAY [ 0.515s] writing 'recovery'... (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 0.811s target max-sparse-size: 256MB sending 'system' (262143 KB)... OKAY [ 8.315s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 8.424s target max-sparse-size: 256MB sending 'system' (239764 KB)... OKAY [ 7.628s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 7.644s target max-sparse-size: 256MB sending 'system' (250695 KB)... OKAY [ 7.940s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 7.956s target max-sparse-size: 256MB sending 'system' (255001 KB)... OKAY [ 8.081s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 8.096s target max-sparse-size: 256MB sending 'system' (257746 KB)... OKAY [ 8.174s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 8.190s target max-sparse-size: 256MB sending 'system' (261982 KB)... OKAY [ 8.284s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 8.284s target max-sparse-size: 256MB sending 'system' (262140 KB)... OKAY [ 8.299s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 8.315s target max-sparse-size: 256MB sending 'system' (247037 KB)... OKAY [ 7.784s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 7.800s target max-sparse-size: 256MB sending 'system' (262140 KB)... OKAY [ 8.284s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 8.299s target max-sparse-size: 256MB sending 'system' (219553 KB)... OKAY [ 6.942s] writing 'system'... (bootloader) Invalid signed image (bootloader) Preflash validation failed FAILED (remote failure) finished. total time: 6.942s erasing 'cache'... OKAY [ 0.031s] finished. total time: 0.031s erasing 'userdata'... OKAY [ 0.203s] finished. total time: 0.203s erasing 'clogo'... OKAY [ 0.031s] finished. total time: 0.031s ... OKAY [ 0.016s] finished. total time: 0.016s ... OKAY [ -0.000s] finished. total time: -0.000s ------------------------------------------------------------------------- please scroll up and check your flash for any errors ------------------------------------------------------------------------- Press any key to continue . . .
---------- Post added at 10:11 AM ---------- Previous post was at 09:48 AM ----------
Is this because of invalid signed image
sreenash said:
I have Indian moto turbo xt1225. Till now I am using different Rom after boot loader unlocked lastyear. Last week I have planned to sell my phone. so I decided to relock boot loader. So I put command OEM lock in fast boot and bootloader got locked. The sad thing that I have forgotten to tick allow OEM unlock in developer option before doing this. Now my phone is bricked and bootloader is in locked condition. I can't push any Rom or recovery via adb or fast boot because of locked bootloader. I googled how to unlock bootloader in fast boot mode, but no solution is seen. Sombody says flashing factory firmfare via rsd lite solve the problems as it doesn't need uncloked bootloader. But when I flashing mtoturbo lollipop Indian factory version given in this forum, flashing failed message came in rds lite .flashing failed boot.img like errors. Kindly help
Click to expand...
Click to collapse
With locked bootloader you have to flash the same or newer firmware for your region than what you had. Every firmware release, no matter how minor, has a new bootloader version.
With an UNLOCKED bootloader you can fastboot all the way back to other region Kitkat 4.4.4 if you wish. Moto Turbo XT1224 launched with Lollipop but Latin America countries had Kitkat for their XT1225. You can flash any region, any version of XT1225 firmware -- IF the bootloader is unlocked, as long as you exclude GPT.bin from your flash commands.
With locked bootloader, you can only flash the region for your XT1225 (India) and only the latest date firmware ever installed or you can update to even newer.
The problem is in India, the "most recent" firmware which was delivered via OTA was NEVER released as full image file. Most are looking for this file: The problem is Motorola apparently never publicly released the India (RETEU) "GS" region full image version of this firmware. They only released the partial image OTA.
XT1225_QUARK_RETEU_6.0.1_MPGS24.107-70.2_cid7_subsidy-DEFAULT_CFC.xml
So, you have to go to a Motorola Service Center for them to install it for you. See here for more information.
https://forum.xda-developers.com/showpost.php?p=77072321&postcount=5
ChazzMatt said:
With locked bootloader you have to flash the same or newer firmware for your region than what you had.
Click to expand...
Click to collapse
Can I flash it in fastboot with twrp stock image backup taken earlier
sreenash said:
Can I flash it in fastboot with twrp stock image backup taken earlier
Click to expand...
Click to collapse
No, not in fastboot you cannot flash TWRP images.
Hello,
OP6 OOS 9.0.9 OTA 34. rooted.
I wanted to upgrade to OOS 10... I see install last magisk and twrp... so...
I wanted to install a new version of blu_spark (zip version) directly since old blu_spark recovery... and when I wanted to restart ... (so i make a big mystake)
I started reading the tutorials this morning around 9:00 am.
It's 3:30pm and I haven't found anything or rather I've found things that don't work. :crying:
Phone is locked in fastboot mode... no issu. no logo, no recovery...
When i want to flash in ADB I have "Failed to load/authenticate boot image: Load Error"
Phone is reconised bye windows on "android bootloader interface"
I see tuto for MSMdowloadtools 4... but my last W10 don't want to boot in test mode
Is the only way to unbrick?
I think, bootloader is corrupt, so it's possible to reinstall the correct bootloader? (version for OOS 9 and not 10...)
fastboot oem device-info
(bootloader) Verity mode: false
(bootloader) Device unlocked: true
(bootloader) Device critical unlocked: false
(bootloader) Charger screen enabled: true
(bootloader) enable_dm_verity: true
(bootloader) have_console: false
(bootloader) selinux_type: SELINUX_TYPE_INVALID
(bootloader) boot_mode: NORMAL_MODE
(bootloader) kmemleak_detect: false
(bootloader) force_training: 0
(bootloader) mount_tempfs: 0
(bootloader) op_abl_version: 0x0
(bootloader) cal_rebootcount: 0x31
OKAY [ 0.087s]
finished. total time: 0.110s
When I try : fastboot flash recovery twrp-3.3.1-x_blu_spark_v9.107_op6.zip
I have:
target reported max download size of 536870912 bytes
sending 'recovery' (16225 KB)...
OKAY [ 0.372s]
writing 'recovery'...
FAILED (remote: (recovery_b) No such partition)
finished. total time: 0.380s
I test:
fastboot flash boot twrp-3.2.1-0-enchilada.img
target reported max download size of 536870912 bytes
sending 'boot' (26748 KB)...
OKAY [ 0.622s]
writing 'boot'...
OKAY [ 0.158s]
finished. total time: 0.788s
OK !
Now, I have a black screen with QUALCOMM Crashdump mode
So?
Download the fastboot rom and put your phone in bootloader mode and flash
vuittion said:
Download the fastboot rom and put your phone in bootloader mode and flash
Click to expand...
Click to collapse
Hello !
Yes, can you be more detailed? :angel:
ps: phone is on QUALCOMM CrashDump Mode and I can't have nothing else...
I managed to reboot to my old recovery and then to the A partition. :laugh:
I go to OOS 9.0.8
So, It's possible to move to OOS 10 now? without problem?
https://forum.xda-developers.com/oneplus-6/how-to/rom-stock-fastboot-roms-oneplus-6-t3796665
vuittion said:
https://forum.xda-developers.com/oneplus-6/how-to/rom-stock-fastboot-roms-oneplus-6-t3796665
Click to expand...
Click to collapse
Thks.
Why this way don't work? >
[Dirty Flash] For Users with an Unlocked Bootloader and TWRP Recovery coming from Stable OxygenOS, OxygenOS Open Beta
Download the full ROM zip and TWRP recovery from the downloads section above
Transfer the full ROM zip and TWRP recovery to the root of your device's internal storage
Reboot to TWRP recovery and take a nandroid backup of your existing ROM
From the TWRP menu, Install > Select full ROM zip > Swipe to flash
From the TWRP menu, Install > Select TWRP recovery zip > Swipe to flash
Reboot to TWRP recovery
Flash the latest stable Magisk in case you want to root
Reboot to System
?