Database Info

leagoo t5 wont boot after unlocking bootloader

Had a bad idea this morning and decided to try to root the phone, leagoo t5. The last time Im going to go messing with a phone that wasnt broken! after spending 10hrs trying to sort it! I downloaded adb tools and and twrp. I unlocked the bootloader with fastboot and installed twrp. However when I rebooted the phone it just booted straight into twrp. I cant get it to boot normally. I reinstalled the firmware but it will still not boot. I can get into recovery and factory modes but thats it. what can I do? Thanks

pcfreeze said:
Had a bad idea this morning and decided to try to root the phone, leagoo t5. The last time Im going to go messing with a phone that wasnt broken! after spending 10hrs trying to sort it! I downloaded adb tools and and twrp. I unlocked the bootloader with fastboot and installed twrp. However when I rebooted the phone it just booted straight into twrp. I cant get it to boot normally. I reinstalled the firmware but it will still not boot. I can get into recovery and factory modes but thats it. what can I do? Thanks
Click to expand...
Click to collapse
Have you tried factory resetting in recovery?

ktmom said:
Have you tried factory resetting in recovery?
Click to expand...
Click to collapse
Yes I did. No Joy. When I power on I just get the leagoo logo coming on and off repeatedly. Pressing the power button then will not turn the phone off again. I can switch it off by pressing vol- and pwr together though.
Is the problem caused by unlocking the bootloader with fastboot or that the firmware I installed is not suiting? Rebooting the phone after unlocking the bootloader before reflashing the firmware caused the leagoo logo to come on and off repeatedly accompanied by this message in very small text "Orange State - Your device has been unlocked and can't be trusted, Your device will boot in 5 seconds". After flashing the firmware with Sp Flash Tool this message is not being shown. Does reflashing firmware undo the action of unlocking the bootloader?

What your are describing is a bootloop. It sounds like the device can not find the system kernel to boot to. Did you boot the device after unlocking but before doing anything else?
Where did you get the TWRP recovery from?
Isn't this a mediatek chipset? If so, I think you need to use SP Flash Tool*to install.
I would look for a stock ROM for this device to revert to.
I'm not experienced on mediatek devices, but maybe @SubwayChamp could help.

pcfreeze said:
Yes I did. No Joy. When I power on I just get the leagoo logo coming on and off repeatedly. Pressing the power button then will not turn the phone off again. I can switch it off by pressing vol- and pwr together though.
Is the problem caused by unlocking the bootloader with fastboot or that the firmware I installed is not suiting? Rebooting the phone after unlocking the bootloader before reflashing the firmware caused the leagoo logo to come on and off repeatedly accompanied by this message in very small text "Orange State - Your device has been unlocked and can't be trusted, Your device will boot in 5 seconds". After flashing the firmware with Sp Flash Tool this message is not being shown. Does reflashing firmware undo the action of unlocking the bootloader?
Click to expand...
Click to collapse
Then to unlock bootloader is not normal that Android refuses to boot normally but when you flash a custom recovery or modify other partition this usually could happen so either or both you have to do a factory resetting/format data as @ktmom said or/and flash a kind of DM-verity for your device, this last avoids that bootloader checks the integrity of the partitions and can boot normally to system.
The warning message is normal then to unlock bootloader and reflashing the stock rom doesn´t relock it, you have to relock it at similar way that you unlocked it via fastboot command, most commom is "fastboot oem relock" but there are other variants and keep in mind that you have to return completely to stock before to apply it.

SubwayChamp said:
Then to unlock bootloader is not normal that Android refuses to boot normally but when you flash a custom recovery or modify other partition this usually could happen so either or both you have to do a factory resetting/format data as @ktmom said or/and flash a kind of DM-verity for your device, this last avoids that bootloader checks the integrity of the partitions and can boot normally to system.
The warning message is normal then to unlock bootloader and reflashing the stock rom doesn´t relock it, you have to relock it at similar way that you unlocked it via fastboot command, most commom is "fastboot oem relock" but there are other variants and keep in mind that you have to return completely to stock before to apply it.
Click to expand...
Click to collapse
I relocked the boot loader with the command "fastboot flashing lock". small white text dialogue on phone screen stated bootloader was locked successfully. rebooted phone then and it was still stuck in the boot loop. For a few seconds in between the leagoo logo a strange circular graphic was displayed on the phone with word "erasing" under it. What does this mean?
Can you tell me more about how to flash DM-verity?

pcfreeze said:
I relocked the boot loader with the command "fastboot flashing lock". small white text dialogue on phone screen stated bootloader was locked successfully. rebooted phone then and it was still stuck in the boot loop. For a few seconds in between the leagoo logo a strange circular graphic was displayed on the phone with word "erasing" under it. What does this mean?
Can you tell me more about how to flash DM-verity?
Click to expand...
Click to collapse
Ok, then to relock bootloader I guess that you did successfully boot to system again, right?
When you unlocked bootloader first then device is formatted to avoid a new user can access to the user´s data and when you relock it again the same happens.
As for DM-verity, newer devices strictly since nougat can´t boot to system after any partition was modified like happened when you flashed a custom recovery on it, here is when DM-verity can be useful, is used to avoid bootloader checks the integrity and allow a modified device can perform a reboot and more custom actions not officially permitted. You had to flash it through a custom recovery, sometimes flashing only Magisk is enough but not always.

You *might* be able to use this universal dm-verify script. It can be flashed only in a custom recovery and I'm not certain that is available to you.

ktmom said:
You *might* be able to use this universal dm-verify script. It can be flashed only in a custom recovery and I'm not certain that is available to you.
Click to expand...
Click to collapse
Good news and bad news! I got the phone to boot! I reinstalled twrp and the "magisk","no verity opt encrypt" and "disable dm verity" zips from the ext sdcard with fastboot. Twrp stated the zips installed ok but there were also some red line failure lines in the dialogue as they were being installed. I rebooted the phone via fastboot but this just resulted in it booting direct to twrp as before. I tried normal boot from twrp but it still booted straight back to twrp. I then tried selecting normal boot from the fastboot, normal, recovery option menu accessed on the Leagoo T5 by powering off the phone and then pressing the pwr and vol+ buttons together but this still resulted in it booting straight to twrp. I then decided to uninstall twrp by flashing the stock firmware recovery image to try to boot from stock recovery. I did same and rebooted from fastboot and it booted to system.
The bad news is there is an imei failure message and the sim is not connecting to the network.I googled imei failure and saw that its can happen when firmware is changed. I installed the "mobileuncle" app but according to a youtube video I watched, when I tap "Engineer Mode" there should be 2 further options available, one being MTK Mode. I am only getting one option "Engineering Mode (Android) which when I select just results in being returned to the previous menu. please say this is not a major problem!

@pcfreeze you quoted me, but as I said earlier, I'm not experienced with mediatek devices. You'd be better off quoting @SubwayChamp

pcfreeze said:
Good news and bad news! I got the phone to boot! I reinstalled twrp and the "magisk","no verity opt encrypt" and "disable dm verity" zips from the ext sdcard with fastboot. Twrp stated the zips installed ok but there were also some red line failure lines in the dialogue as they were being installed. I rebooted the phone via fastboot but this just resulted in it booting direct to twrp as before. I tried normal boot from twrp but it still booted straight back to twrp. I then tried selecting normal boot from the fastboot, normal, recovery option menu accessed on the Leagoo T5 by powering off the phone and then pressing the pwr and vol+ buttons together but this still resulted in it booting straight to twrp. I then decided to uninstall twrp by flashing the stock firmware recovery image to try to boot from stock recovery. I did same and rebooted from fastboot and it booted to system.
The bad news is there is an imei failure message and the sim is not connecting to the network.I googled imei failure and saw that its can happen when firmware is changed. I installed the "mobileuncle" app but according to a youtube video I watched, when I tap "Engineer Mode" there should be 2 further options available, one being MTK Mode. I am only getting one option "Engineering Mode (Android) which when I select just results in being returned to the previous menu. please say this is not a major problem!
Click to expand...
Click to collapse
It could be many reasons why device didn´t boot to system. Then to flash it you had to format data + flash DM-verity. Also is possible that this TWRP version is not completely suitable for your device or is unable to mount/unmount partitions correctly, you have to check from where you downloaded it and if some users are experiencing similar issues with it.
As per you IMEI lost, better is ever take a backup of the NVRAM through TWRP before to go further then it´ll be easy to recover it. In almost all firmwares for mediatek devices you´ll fnd inside the zips SPFT and SN Writer that is to recover your IMEI. Your IMEI is not really lost only got actually covered by blank codes due to a bad/incorrect flashing/wrong sequence firmware, so be careful what you do with Mobile Uncle tool if you´re not experimented with otherwise you´ll lost permanently.

SubwayChamp said:
It could be many reasons why device didn´t boot to system. Then to flash it you had to format data + flash DM-verity. Also is possible that this TWRP version is not completely suitable for your device or is unable to mount/unmount partitions correctly, you have to check from where you downloaded it and if some users are experiencing similar issues with it.
As per you IMEI lost, better is ever take a backup of the NVRAM through TWRP before to go further then it´ll be easy to recover it. In almost all firmwares for mediatek devices you´ll fnd inside the zips SPFT and SN Writer that is to recover your IMEI. Your IMEI is not really lost only got actually covered by blank codes due to a bad/incorrect flashing/wrong sequence firmware, so be careful what you do with Mobile Uncle tool if you´re not experimented with otherwise you´ll lost permanently.
Click to expand...
Click to collapse
I got into engineering mode via dialer code. CDS option was missing from connectivity. I installed https://m.apkpure.com/cds-mobile/com.doubleapaper.cds.cds_mobile but CDS is still missing from engineering mode

pcfreeze said:
I got into engineering mode via dialer code. CDS option was missing from connectivity. I installed https://m.apkpure.com/cds-mobile/com.doubleapaper.cds.cds_mobile but CDS is still missing from engineering mode
Click to expand...
Click to collapse
Sorry, just realised that this is the wrong app! nothing to do with cds in engineering mode! I triedhttps://apkcombo.com/common-data-service/com.mediatek.connectivity/
but got message that the file was corrupted and it would not install

Phone is Cycling between Bootloader Unlocked Screen and Motorola Sp

I just tried rooting my phone. The phone is cycling back and forth between the bootloader is unlocked screen and the Motorola splash screen.
To repeat some steps from a prior post.
My phone had QPR30.80-58-3 .
I downloaded that ROM and extracted the boot.img file.
I downloaded the latest Magisk Manager and installed it on my phone.
I ran through the patching process for boot.img.
I requested an unlock code from Motorola and unlocked the bootloader.
I flashed the patched boot image which patched partition b.
I flashed the patched boot image to partition a.
I rebooted which began the cycle.
I tried holding down the power button but it returns to the cycle.
I can get back to the bootloader with the Volume Down and Power buttons.
Any suggestions on what could get me back to a functioning phone, rooted or not rooted?

I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.

dafunk60 said:
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
Click to expand...
Click to collapse
I checked that the image I patched was from the QPR30.80-58-3 ROM which matched the level after the phone was updated.
I flashed that original boot image which flashed partition a and then rebooted. I did not flash partition b.
It first came up with the unlock warning screen. It sat on the Motorola splash screen for a noticeable amount of time followed by a yellow screen with a circle around the Motorola symbol. Finally it ended up on a blue Hello there screen with a yellow start button.
This screen was unresponsive. Eventually through various cyclings through all this I ended up on a screen that said Android could not boot and gave me an option of a factory reset. I did that but it did not help getting past the Hi there screen.
I went back and flashed the QPR30.80_58 image on both partitions a and b. This got me back to setting up the phone again. The phone is at QPR30.80_58. I am considering just rooting at this level.

So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.

DougPeterson said:
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
Click to expand...
Click to collapse
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.

dafunk60 said:
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
Click to expand...
Click to collapse
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?

DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If you want to get into recovery, boot into the bootloader than do
Code:
fastboot reboot fastboot
That'll boot you into fastbootd which has an option to go to the real recovery

DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If adb isn't showing any devices connected that would explain why the rescue software cannot find your phone. Perhaps you don't have the correct driver installed. Windows Device Manager shows the phone as a Motorola ADB Device on my PC.
View attachment 5061327
Another possibility is that you have multiple versions of adb on your PC. Older versions won't work but the adb.exe in "C:\Program Files (x86)\Rescue and Smart Assistant" works for sure. With your phone booted into android & unlocked, plug it into your PC. Do you see the "USB debugging connected" on the phone? If you don't I would re-check that USB debugging is enabled. If you do see the debugging notification, on your PC, open a command prompt and navigate to "C:\Program Files (x86)\Rescue and Smart Assistant". Run
Code:
adb devices
Does adb find your phone?

Factory mode formats ALL data? Start up failed, only bootlader problem?

Hello guys, I try to explain myself as best as I can.
I have a Motorola Moto G7 power NOT rooted.
I tried to clean the cache from the menu that appears with Volume down+Power on. I chose "Recovery mode" but no menu appeared. So I chose "Factory mode", I thought that various voices appeared, but from that moment the phone hasn't started up anymore and he tells me:
Code:
start up failed
your device didn't start up successfully
use the Software Repair Assistant on computer to repair your device
AP Fastboot Flash Mode (Secure)
No bootable A/B slot
Failed to boot Linux, falling back to fastboot
Fastboot reason: Fall-through from normal mode
I downloaded that software but it will flash the device.
I have already tried:
- "restart bootlader": it remains on recovery mode.
- "recovery mode": for half a second, the Motorola logo appears and then:
Code:
start up failed etc
No bootable A/B slot
Failed to boot Linux, falling back to fastboot
Boot up failed
- "start": same error above
Now, beyond the fact that I ****ed up and I am aware of it, can I recover only the bootloader? When I chose "Factory mode" none writing appeared, so... it's possibile that my phone was completely formatted in one second? I thought the data, settings, etc are still there but it just screwed the bootloader, is it possible? And how to fix it? I found only guide to flash the phone.
Thanks.

Solved!
Luckily, "factory mode" did not cancel my data, I searched better on the forum and found a way to flash the original firmware without losing data. The Software Repair Assistant flashes only with complete formatting, so you have to change a string of a flashfile.xml before flash with the Software Repair.
Thanks to here and here for the instructions, here a summary:
(The program does not have the download progress bar. You can see the full download from:
- the Rescue now button turns orange
or
- the complete file in C: \ ProgramData \ LMSA \ Download \ RomFiles \ YOUR_FILE.xml )
Once the firmware is downloaded, don't continue with flashing.
Open C:\ProgramData\LMSA\Download\RomFiles
Select the firmware for the device you want to flash
Open the flashfile.xml with a text editor like notepad++ (https://notepad-plus-plus.org/) (I used standard notepad)
Delete this line
Code:
<step operation="erase" partition="userdata"/>
save the changes
Continue the flashing with LMSA
Click to expand...
Click to collapse
At the end, the phone turned on as I left it, apps, data, settings, everything
PS: you can find the Software on the official lenovo support
https://support.lenovo.com/in/en/downloads/ds101291

Sbubba said:
Hello guys, I try to explain myself as best as I can.
I have a Motorola Moto G7 power NOT rooted.
I tried to clean the cache from the menu that appears with Volume down+Power on. I chose "Recovery mode" but no menu appeared. So I chose "Factory mode", I thought that various voices appeared, but from that moment the phone hasn't started up anymore and he tells me:
Code:
start up failed
your device didn't start up successfully
use the Software Repair Assistant on computer to repair your device
AP Fastboot Flash Mode (Secure)
No bootable A/B slot
Failed to boot Linux, falling back to fastboot
Fastboot reason: Fall-through from normal mode
I downloaded that software but it will flash the device.
I have already tried:
- "restart bootlader": it remains on recovery mode.
- "recovery mode": for half a second, the Motorola logo appears and then:
Code:
start up failed etc
No bootable A/B slot
Failed to boot Linux, falling back to fastboot
Boot up failed
- "start": same error above
Now, beyond the fact that I ****ed up and I am aware of it, can I recover only the bootloader? When I chose "Factory mode" none writing appeared, so... it's possibile that my phone was completely formatted in one second? I thought the data, settings, etc are still there but it just screwed the bootloader, is it possible? And how to fix it? I found only guide to flash the phone.
Thanks.
Click to expand...
Click to collapse
Edit:
I'm not sure why selecting factory mode would cause such a problem.
Glad you got it working again.
Sent from my Moto E (4) using Tapatalk

Redmi note 7 stuck in a bootloop. Can only access stock recovery, is it fixable?

Good morning!
While attempting to flash a stock MIUI 10 ROM into my Xiaomi Redmi Note 7, to downgrade back to Android 9.0 due to some app compatilibty issue, I messed up big time and my phone is now stuck in a loop where the screen turns on, nothing shows up, then it restarts, going off for a few seconds and turning on again.
Power Button + Volume UP successfully brings me to the stock recovery 3.0 from xiaomi.
Power Button + Volume DOWN fails to bring me to the fastboot mode.
If I select the Connect with MIAssistant in the recovery the phone will show up as "sideloaded" after using the command adb devices, but the MIPCSuite app does not see it and the command adb restart bootloader also fails to bring up the fastboot mode, it just gets stuck in the loop again.
More context on what went wrong and caused this: I followed an online tutorial to flash a rom using the MIFlash app, so I unlocked the bootloader and tried to flash the rom usin xiaomi's tool. I got a failed to check sparse crc error code and it went downhill from there when I tried to fix things reading multiple threads on the issue. I tried deleting some lines from the flash_all.bat file and tried to flash it again but then the flashing process went seemingly forever so I aborted the operation and now this loop happens. I tried a few more times but with no success.
The first time I tried to use the tool I used the clean all and lock option so I'm not certain if the miflash tool locked the bootloader regardless of the outcome of the flashing attempt.
Is there hope? Can I fix this phone if I only have access to stock recovery and nothing else (although it shows up in adb devices but can't get into fastbootmode) ?
Thanks a lot to anyone who took the time to read and possibly help.

Both ADB and Fastboot are Android-side launched by device's bootloader. If you can't enter Fastboot mode then my guess is there is something is wrong with curently installed Android.
BTW: If you lock device's bootloader then bootloader attempts to load device's Stock ROM.

jwoegerbauer said:
Both ADB and Fastboot are Android-side launched by device's bootloader. If you can't enter Fastboot mode then my guess is there is something is wrong with curently installed Android.
BTW: If you lock device's bootloader then bootloader attempts to load device's Stock ROM.
Click to expand...
Click to collapse
I see.
What can I do to try to fix this issue?

I finally managed to fix it through the Emergency Download Mode (EDL). It requires Xiaomi Authentication which I bypassed using this guide: https://www.droidwin.com/fix-mi-account-authorization-unbrick-xiaomi-edl-mode/
With that setup I flashed a stock rom using the MiFlash tool.

Pixel 2: Slot Unbootable: Load Error

I have a pixel 2 which is stuck in bootloader due to "Slot Unbootable: Load Error".
So far I tried to flash / wipe the device with https://flash.android.com/ but the process can't be started due to "Device Unlock Disabled".
Anyone got some hints for me?

Unfortunately your options are rather limited because the bootloader is locked, and because OEM Unlocking is off (get_unlock_ability=0), unlocking it is not possible. This is one of those shortcomings I think should be addressed in Pixel devices but that's another conversation for another time.
Are you able to boot into recovery or Download Mode?
I'll break out my old Pixel 2 when I get home and see if I can figure something out.

Trying to boot into Recovery Mode gives the same Load Error. Trying to boot into Download Mode gives: "ERROR: Operation Denied" .

50g said:
Trying to boot into Recovery Mode gives the same Load Error. Trying to boot into Download Mode gives: "ERROR: Operation Denied" .
Click to expand...
Click to collapse
Yeah, I had the same result on my Pixel 2.
Rescue Mode unfortunately wasn't introduced until the Pixel 3.
Unfortunately I don't think there is any way to fix your device beyond taking it to a repair center and having them replace the mainboard...unless you can find someone who has both the Qualcomm Product Support Tool as well as the necessary files. It's not possible to flash the device via bootloader when bootloader is locked; the prescribed method to update outside of system is via recovery (ADB sideload).
Sorry I couldn't be of more help.

I was concerned that might be the case. Appreciate your efforts.