Hi all,
Stock rom, was listening to youtube on the road, thought I hit a dead zone but then signal never came back. Now i get "error while searching for networks" if i hit setting and search under the network operators setting.
Network type is correct,
Tried sim in another phone, sim works just fine in different phone.
WiFi calling still works in the problem phone.
I dialed *#*#4636#*#* ... It tried to call that number "this call cannot be completed as dialed" .
Apn is correct.
Did my antenna just die out of the blue? Thats a thing?
It was hot in the car YESTERDAY, but it has been working fine all day the next day. Screen glue also failing... Maybe it's time to replace but the issues thus far were only cosmetic.
Cell radios can just suddenly die?
Ok. Somehow whilest viewing a youtube video the wifi calling setting got flipped to ONLY USE WIFI, NEVER CELLULAR!
Go figure......
Tmobile tech support figured it out. I checked everything except that setting!
Related
First this only happens where I work in the basement where only certain providers (eg Verizon) have some signal in only part of the room. I did not get signal on AT&T or T-Mobile Pay as you Go down here.
I noticed especially after I flashed the new radio which gives me better service overall that I get phone signal down in the basement, but it is GPRS of Unknown Network and says emergency calls only. I get up to 3 bars. If I scan for available networks I get the name 31064.
Does anyone know what network that is or what is going on?
Anyone have any ideas? (I will take wild speculation as well)
i wouldn't be alarmed by it. I experience this at my office since I work in the basement...haha
It's possible your basement just won't read a signal like mine. install a window by your desk, maybe that'll help, but there shouldn't be anything wrong with your handset.
Sounds reasonable. I would agree with no problems with my handset. I do get better signal than my nokia e51, so maybe it's picking up a slight signal where the nokia could not.
From what I've noticed, my Nexus S acts this way whenever T-Mobile (my provider) does not have coverage wherever I am, but AT&T (not my provider) does. You can check this by going into "settings" -> "wireless & network settings" -> "mobile networks" -> "network operators" .....it will then search for & tell you what network has coverage where you are. Every time I've had bars & it says "emergency calls only" & I've checked the above, it's always been when I had coverage from AT&T but not T-Mobile.
Thus, it seems to me like an "enable roaming for emergency calls only" kinda thing.
Emergency calls only
ha ha....lol... i also have the same issue on my brand new i747M S3. im confused.
i try the all methods for resetting phone.
i noticed when im on long way, i dont know my handset is goning emergency calls only. but when im restsart phone its fine.
i do everything but not fixed it. firmware update, downgrade, rom change,and unroot. but not fixed, and also try factory reset the rom by falllowing the samsung secret code *#197328640# > UMTS>COMMON>NV REBUILD and restart and do again CDMA>COMMON>NEXTPAGE>REBUILD and restart., thhis is the code of full factory reset the rom and EFS. but not solve........
i change the hand set to international i9305 brandnew one. i used it 2 sady without issue.... day after morning when i wakeup, i see the massege,,,,emergency calls only,,im confused becouse this is a brandnew one...after i called the friend he also got the i9305. i asked about this issue. he said me he didnt face to this type of issue.. im confused he said me try sim change.. i do it... problem solved....:victory:
problem is the SIM card......i changed it to new one... and used i week no emergency calls issue... when im going to low signals areas.. its show no network and automaticallly change to the network....im very happy for fixing this problem.....:laugh::laugh::laugh:
Hi,
I am actually on holiday, and for the first few days my nexus s (running masters deodexed 2.3.3 with voodoo kernel) was working fine. However for the last day and half, it has been stuck on Emergency Calls only. I have tried everything to fix it, switching to airplane mode, full reboot, going into settings, wireless and networks and manually selecting a network but it still only remains in Emergency mode only.
I pressed *#*#4636#*#* and under phone information, GSM service says Emergency Calls Only
I have tried switching off and on the radio and fiddling with the preferred network type but nothing seems to work. I dont know if this is a roaming issue (i dont think it is because it was working fine initially abroad) but any help will be most appreciated.
Thanks,
Hi, I am having this same problem too. I have the Nexus S from Koodo and it seems like it doesn't "like" my simcard. I also have a fido simcard on me and the Nexus S works fine on my Fido simcard. Today i went to a Koodo store and tried another one of the simcards and it didn't work either. So far I think my Nexus S is defective. You can PM me your email if you like if you want to see if i fix it.
[Not Fixed] see bottom of this post.
It is fairly easy to install a new D6603 to work completly on the AT&T network. It is not so easy to find the answer of how to do it in the threads and posts. I tried many suggestions and wasted a lot of time. Hopefully this will save you from that fate.
First you must know that you can't use the IMEI number of your new phone if you want it to work completly as it should. If you use the Z3 IMEI you will have trouble with data of various sorts and the phone will go off line when on LTE after 20 or 30 minutes and you will not receive calls or SMS messages. I do not know why but it has been suggested that the AT&T network does not recognise this phone so it causes trouble.
If you have an AT&T nano-sim from your old phone then just put it in the phone. (Cut downs work but can cause other problems some say.) When the SIM is inserted for the first time into a new phone there is a prompt that asks if you want to download the APN. Hit 'yes' and the phone downloads the APN itself.
If it does not ask then go to Settings>More>Mobile Networks>Prefered Network Type and be sure LTE (Preferred) is selected. Then connect your phone to the internet and then go to Settings>More>Internet Settings and select AT&T. You should be good to go.
If you need to get a nano-sim then go to the AT&T store or call and they will give you one or send you one for free. You will need to use the IMEI number from a LTE phone that is already on the AT&T system. You can use your old phone or borrow the number from someone. If the rep installs the sim in the Z3 with the 6603 IMEI don't worry. Just call support later and tell them you sent your new phone back and want to go back to your old IMEI or have a new IMEI (from an existing AT&T phone). They will enter it and off you go. The phone from the IMEI will show in the picture on your account page. Big deal!
Update: This worked for hours last night but this morning it is back to not receiving calls. Simply turning wifi off and it began to receive calls as GPRS was switched back on. My wifi was on which has been said to cause problems. I will test with wifi off and report back. Had "no service" instead of AT&T on upper left of lock screen. A full shut down for several minutes than re-boot solved that.
YMMV. I've been on ATT with a Z3 purchased from Sony store for several months and it was registered in an ATT store by scanning the IMEI off the box followed by updating Internet settings in Setup. ATT online shows unknown model but everything works including LTE and MMS. There is something else involved when problems like this occur probably some setting not getting reset. I registered the Z3 on a new line with a new Sim card because I wanted to take my time moving stuff off my old phone--this may have avoided the problems.
JudH said:
YMMV. I've been on ATT with a Z3 purchased from Sony store for several months and it was registered in an ATT store by scanning the IMEI off the box followed by updating Internet settings in Setup. ATT online shows unknown model but everything works including LTE and MMS. There is something else involved when problems like this occur probably some setting not getting reset. I registered the Z3 on a new line with a new Sim card because I wanted to take my time moving stuff off my old phone--this may have avoided the problems.
Click to expand...
Click to collapse
I've also had no problems with my Z3 on AT&T. Works great, receives sms/mms immediately, etc..
esheesle said:
I've also had no problems with my Z3 on AT&T. Works great, receives sms/mms immediately, etc..
Click to expand...
Click to collapse
AT&T's system sometimes takes a while to get updated with new IMEIs that trigger LTE provisioning for a users' account.
Once your account is provisioned for LTE you never have to worry about it again, but sometimes if you have a phone the system doesn't recognize, it is a pain to get AT&T to properly provision your account. Supposedly properly trained in-store reps can do it - the key being "properly trained" - Never try to do anything "unusual" by calling AT&T customer service, and NEVER use a franchise/kiosk in-person for service - make sure you're at a corporate-owned store! Even then, some stores might have incompetent staff. I've been lucky that all of my local corporate stores are pretty well staffed.
So you are saying that your Z3's with wifi and LTE on with AT&T are working as they should?
With LTE off my phone responds normally with wifi on. With LTE and wifi on it will not respond to calls after a 30 minute sleep. It does not show missed calls. Calls go straight to voice mail after 2 rings. Could you tell me what level your LTE dBm's are? Thanks!
I was told not to give them my imie# but, after recvng the minisim I had to call them in order to 'provision' it to work at all and they needed that #. I have never had any problems personally and am assuming this may be because you gave them the wrong #. Again I am only guessing. Oth, if I had had a different imie to give, I would have done so myself.
It is very strange and I am feeling it is more signal strength related than how you provision your phone. (Once it is provisioned correctly.) It seems that more people have less problems when they already have a nano-sim and just plunk it in the new phone. This might indicate that they already had a strong signal from the get go. My old HTC One + get's a better signal than the Sony in the same locations with the same (new) SIM. With the Devilcase bumper on it gets 5% less. My very limited tests yesterday seemed to indicate that it was signal strength related. I am not enough of a conspiracy theorist to imagine that AT&T would program their system to not function correctly with sims that are provisioned with these Sony phones which they are obviously ignoring for some reason. Or am I?
I had all kinds of problems with the Z3 on AT&T. The IMEI caused an issue since AT&T linked it to a flip phone and therefore couldn't provision LTE. I changed it to an old AT&T LTE device and then I was able to get LTE but was having the same issue with calls going directly to voicemail and texts showing up hours later in bunches. I found the solution was to switch off LTE in the quick settings menu. All calls and texts came through and on time while LTE was off. If I needed a data boost to stream, I turned it back on until I was finished streaming. This was while on KitKat. After upgrading to Lollipop, I was able to keep LTE turned on and calls and texts still arrived on time.
I use data rarely. Mostly wifi. If I don't leave LTE on, my phone reverts to wcdma preferred. And why can't LTE just work without me having to constantly turn it back on? What bugs me is having the APN settings greyed out. I want to be able to turn it off. If anything it seems the phone itself is preventing me from accessing the sim. It feels like I'm borrowing something which contains lots of MY private data. I know my phonebook is stored locally but I also noticed there is no option of specifying the sim or not. Anybody know how to switch APN on and off? In fact, overall even rooted, I still feel like I have almost no power over it. I can't even disable the cellular connection without going full on airplane mode and I do not trust that. I don't even fly so that needs work for sure. Dumb question but could I buy a working nanosim from say 7-eleven that my apn switch will work with?
"Anybody know how to switch APN on and off?"
On my Z3 on OTA stock Lollypop I have an icon in quick settings to turn LTE on and off. Drag two fingers down from the top of the screen. If no LTE icon then select the pencil icon at the top and select the LTE icon. There is also a mobile data icon switch there.
To turn off your radio completly you can get the Advanced Signal Status app and select additional info at the bottom and click phone information and turn off radio. Probably a number of ways to do it but that is one.
Sim contact storage was a way to move information from phone to phone. You can still do it but not really necessary with cloud backup and storage. Google does it for me without me having to do anything which I like. I still save contacts to the sim just because I can. Export and import in your contacts app menu.
johnboatcat said:
So you are saying that your Z3's with wifi and LTE on with AT&T are working as they should?
With LTE off my phone responds normally with wifi on. With LTE and wifi on it will not respond to calls after a 30 minute sleep. It does not show missed calls. Calls go straight to voice mail after 2 rings. Could you tell me what level your LTE dBm's are? Thanks!
Click to expand...
Click to collapse
Works fine here. I don't pay attention to the dBm estimates since these aren't measured with calibrated test equipment and vary widely. Those numbers are basically worthless.
The only valid comparison is data performance in a given environment (ideally a difficult weak-signal one) - and at my desk with very weak signal, every phone I've ever used performs similarly to the Z3.
"Those numbers are basically worthless."
True, but we have narrowed this down to the possibility that it might be signal related so it is worth a shot. If people whose phones are working fine would measure the LTE dBm on Advanced Signal Status at the location where their phone sits and works well the most we might possibly see some measure of difference in the phones that are not working. Most of the non-working phones seem to work sometimes so signal strength is the next best parameter to rule out. Thanks!
Here are the screen shots of my phone with LTE on, LTE and wi-fi and LTE off and wi-fi.
How do the working phones compare? Does your CDMA (voice) also go to 0% when LTE is on and GSM = n/a?
Thanks. I think adv sig nfo actually works. I'm amazed actually. I can't find the phone's native greyed out apn switch anyways which really makes no sense.
I've been using Three on my OPO for a couple of weeks now after I transferred from Giffgaff.
I am trying to avoid speaking to the support at three as they are notoriously bad. I've tried emailing them twice about settings after I searched everywhere for APN settings and advice. Eventually I managed to get a basic APN from a post on here along with instructions on how to change the preferred network type. However I am unsure I have covered everything and I have been having issues with the reception dropping out.
When it does drop out it keeps telling me there is no network (giffgaff) even though I think I've got it set up for 3, which is confusing me.
Other than the APN and selecting the network, is there a setting I've missed somewhere?
I'm still having issues with my phone dropping signal. I don't know if it is three or the phone. Is there any way to check this?
While sitting at my desk at work, I go from having H+ or LTE to having nothing with the "emergency calls only" notification.
Can anyone help?
a few days ago I switched from cm to AEX 7.1.2 on my moto g. Whether that has anything to do with it I don't know.
Anyway last night the phone was working fine then this morning I see that the cell network is disconnected and the phone doesn't see the simcard. However when I put in another simcard from a different network it works normally. I switch back to my sim and it works for about 20 seconds where I can make a call or text then it shuts down again and dowsn't recognize the sim then does again once I have switched the sims but only for 20 seconds. I don't understand what is happening to the phone and why it is doing this. I need help. I have tried picking different network modes from the list after inserting this code #*#*4636#*#* nothing has worked so far. I haven't systematically gone through each one at a time yet and the list is quite long. I haven't seen a list of modes that long before there are over 10 of them from auto prl to scdma etc... Some of them I have never heard of like the scdma one. wif and bluetooth are working ok if that means anything. Thanks for any help
Also when I go into settings the network section is greyed out and under prefered network type it says Invalid Network Mode (-1) Ignore. I only tried changing the modes when this problem arose my changing these modes was not the cause
i've had similar issues, when i skipped using mobile data for a long time, my non-data SIM would dropout intermittently. i changed SIM slots didn't solve it either. other SIM was fine in either slot. just before replacing what i thought was a faulty SIM, without turning mobile data on, i just set the problematic SIM for data. that solved mys issue. however, running mobile data on back on the original setting didnt cause any more issues either.