Database Info

[Q] Moto G Stuck on Boatloader Unlocked Screen

I need help!!! i have unlock my boatloader then rooted and install CWM while using the CWM i have flash each and everything in my phone like, wipe factory data reset, dalvik cache, format sd card, format system etc and then i restart my phone its stuck on bootloader unlocked screen what should i do please help me! Even its not connecting to Mass storage so then i can place the ROM in SD Card please help !!!:crying:

You don't factory reset with custom recoveries like that, it's not a good idea. Put your phone in fastboot mode and then flash stock firmware from here. READ THOROUGHLY.

Which version of Phone and Android you were running on?
Haris Salam said:
I need help!!! i have unlock my boatloader then rooted and install CWM while using the CWM i have flash each and everything in my phone like, wipe factory data reset, dalvik cache, format sd card, format system etc and then i restart my phone its stuck on bootloader unlocked screen what should i do please help me! Even its not connecting to Mass storage so then i can place the ROM in SD Card please help !!!:crying:
Click to expand...
Click to collapse
Which version of Phone and Android you were running on?

Dont worry, you can reflash your ROM... Which model you are having?

padhu1989 said:
Dont worry, you can reflash your ROM... Which model you are having?
Click to expand...
Click to collapse
i have same problem too....
got stuck on bootloop after flash cm11 , spining forever
i have xt1032 single sim , 16 gb , global gsm
any advice for me....
thank you

kucingbaik2 said:
i have same problem too....
got stuck on bootloop after flash cm11 , spining forever
i have xt1032 single sim , 16 gb , global gsm
any advice for me....
thank you
Click to expand...
Click to collapse
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219

Moto G
deej_roamer said:
Which version of Phone and Android you were running on?
Click to expand...
Click to collapse
I was using 4.4.2 on Moto G Dual Sim, 16 GB.

padhu1989 said:
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Click to expand...
Click to collapse
thank you i will try it
lucky me, i was backup my original stock rom..., if i failed flash CM11 , i will restore my backup, and worked
---------- Post added at 10:56 AM ---------- Previous post was at 10:52 AM ----------
Haris Salam said:
I was using 4.4.2 on Moto G.
Click to expand...
Click to collapse
i have same version too...

You need to follow This guide!
Haris Salam said:
I was using 4.4.2 on Moto G Dual Sim, 16 GB.
Click to expand...
Click to collapse
You need to follow This guide! if your version is asian retail!
[Stock][Firmware Package][XT1033] Asia Retail - Alt. Link [4.4.2][Lock Bootloader]

Moto G
deej_roamer said:
You need to follow This guide! if your version is asian retail!
[Stock][Firmware Package][XT1033] Asia Retail - Alt. Link [4.4.2][Lock Bootloader]
Click to expand...
Click to collapse
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.

Moto G
Haris Salam said:
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Click to expand...
Click to collapse
If the phone version is Asian retial, so is it necessary to install the Asian firmware and rom? or we can install the Europe or US firmwares as well?
cause in Asian retail firmware there are some signal data loss issues. Please Advice.

Both
Haris Salam said:
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Click to expand...
Click to collapse
It is for both, guide has an option to lock bootloader if you want to, i guess which is useless for you.
So just skip 4.1 and 4.3 steps and you will be fine, or download Retail_AS.zip, your choice!

Moto G Dual Sim
padhu1989 said:
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Click to expand...
Click to collapse
I am going to follow these steps. If a found any sort of difficulty or problem will tell u thn. Thanks Friend!:good:

Installing
deej_roamer said:
It is for both, guide has an option to lock bootloader if you want to, i guess which is useless for you.
So just skip 4.1 and 4.3 steps and you will be fine, or download Retail_AS.zip, your choice!
Click to expand...
Click to collapse
Thanks for the support friend! im going to install this.

Haris Salam said:
Is this for locked devices? or for both? cause my phone bootloader is unlocked now.
Click to expand...
Click to collapse
If you don't want to lock your boot loader, you need to skip 4.1 & 4.3 steps...
Sent from my XT1032 using XDA Premium 4 mobile app

You can install other local roms as well, US Global or GB will work fine for you
Haris Salam said:
If the phone version is Asian retial, so is it necessary to install the Asian firmware and rom? or we can install the Europe or US firmwares as well?
cause in Asian retail firmware there are some signal data loss issues. Please Advice.
Click to expand...
Click to collapse
You can install other local roms as well, US Global or GB will work fine for you
But the signal drop issues i am not sure are only related to asian firmware! it has something to with the bandwidth operation problem here!

Haris Salam said:
If the phone version is Asian retial, so is it necessary to install the Asian firmware and rom? or we can install the Europe or US firmwares as well?
cause in Asian retail firmware there are some signal data loss issues. Please Advice.
Click to expand...
Click to collapse
Goahead and flash GB version.. I'm using the GB version in xt1033 and I didn't face any issues so far.. Before flashing custom recovery, there is one recent system update 176.4.1 update which fixes signal issues.. ... Update it first and flash a custom recovery if you want and play with it
Sent from my XT1032 using XDA Premium 4 mobile app

How to get that update
padhu1989 said:
Goahead and flash GB version.. I'm using the GB version in xt1033 and I didn't face any issues so far.. Before flashing custom recovery, there is one recent system update 176.4.1 update which fixes signal issues.. ... Update it first and flash a custom recovery if you want and play with it
Sent from my XT1032 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
So how can i get that update which fixes signals issues. Can you tell me the procedure please.

Flash the GB version first... Reboot the phone.. You will get the update automatically... Or check it manually.. Settings- About phone - system update. Download it and install.. Once the update successfully installed.. Flash the custom recovery... Don't flash any custom recovery before installing G an update..
You need wifi I think to receive the update...
Sent from my XT1032 using XDA Premium 4 mobile app

padhu1989 said:
step1: Download the firmwware from the below link
http://sbf.droid-developers.org/download.php?device=14&file=817
step2: once download extract the zip file using winrar in to a folder..
step 3: Download adb files and extract in to the same folder
To download adb, here is the link
http://forum.xda-developers.com/attachment.php?attachmentid=2599339&d=1393312447
Step 4 then download Retail_GB.rar from the below link and extract it to the same folder where you extracted your downloader firmware.
http://goo.gl/gxSlMW
step 5: boot your phone in to bootloader mode by pressing "Power button + Volume Up" button for 10 seconds and release
step 6: once you entered in to the boot load, connect your phone connected to PC via USB. You can see the message in the boot loader like "USB connected"
Step 7: go the extracted folder, open the command prompt from the extracted folder by pressing shift key + right click and select command prompt...
step 8: Type "Retail_GB" (without Quote and Press Enter)...
once all command completed, select "Normal powerup" in boot loader... (to select "press UP button" not power button..)
this is the rough guide... if you face any issues, let me know...
reference : http://forum.xda-developers.com/showthread.php?t=2542219
Click to expand...
Click to collapse
thank you is work like charm
thank you

[Resolved] One Plus 3 OxygenOs 3.2.2 Installation failed

Hi, I have been using One plus 3 for a week now. Today I received new update 3.2.2 After downloading it, started the update. However after some time, the installation window is saying "Installation failed" with only reboot option given. I am really confused right now. Note : This phone is Chinese variant and was given OxygenOS while purchasing. Any help regarding this would be much appreciated.

farhan37 said:
Hi, I have been using One plus 3 for a week now. Today I received new update 3.2.2 After downloading it, started the update. However after some time, the installation window is saying "Installation failed" with only reboot option given. I am really confused right now. Note : This phone is Chinese variant and was given OxygenOS while purchasing. Any help regarding this would be much appreciated.
Click to expand...
Click to collapse
Same issue. i thought it may be a security with my unlocked bootloader so i reflashed stock recovery and relocked the bootloader. Still failed.
Trying adb sideload now. Will let you know if it works
---------- Post added at 07:04 AM ---------- Previous post was at 07:01 AM ----------
mayerlench said:
Same issue. i thought it may be a security with my unlocked bootloader so i reflashed stock recovery and relocked the bootloader. Still failed.
Trying adb sideload now. Will let you know if it works
Click to expand...
Click to collapse
Success!! Adb sideload the full oxygenos 3.2.2 full rom(1.3gb) and youll be up and running.
Let me know if you need help.

mayerlench said:
Same issue. i thought it may be a security with my unlocked bootloader so i reflashed stock recovery and relocked the bootloader. Still failed.
Trying adb sideload now. Will let you know if it works
---------- Post added at 07:04 AM ---------- Previous post was at 07:01 AM ----------
Success!! Adb sideload the full oxygenos 3.2.2 full rom(1.3gb) and youll be up and running.
Let me know if you need help.
Click to expand...
Click to collapse
Thats great ! However, I am newbie to these things ! Could you please suggest a step by step guide for the procedure ? Thanks a lot in advance.

farhan37 said:
Thats great ! However, I am newbie to these things ! Could you please suggest a step by step guide for the procedure ? Thanks a lot in advance.
Click to expand...
Click to collapse
First you need adb on your computer.
1. Download the ADB For Windows from here :- https://drive.google.com/open?id=0B0...VB1elljU2NPR0k
2. Run the .exe file downloaded from above as Administrator.
3. Press 'Y' every time the installer asks.
4. Continue Driver Installation.
Now,ADB and Fastboot have been installed on your PC. Great
1. Now, go to settings>aboutphone>click buildnumber 10 times to activate developer options.
2. Settings>developer options>enable usb debugging
3. Dowbload the update to your pc fron here: https://mega.nz/#!o4EhnCDZ!lG3IrVdAc6ceIbSLQRRvOzZrzGhL-DObCg0oBtncgDc
4. Connect phone to pc. and boot phone into recovery by powering down phone and booting back up while holding volume down and power button. Using volume buttons navigate to recovery. Use power button as select.
Now go to advanced and click the adb option while in recovery mode.
5. Open command prompt on your pc. Type "adb sideload (Update file zip)".
Type without the quotes and the update zip file is the big file you downloaded, just drag and drop it onto the command prompt window without the parentheses obviously.
Hopefully this helps
let me know if you need more help

Easy Flash to Nougat Tutorial (Unlocked Retail Devices)

Easy Flash to Nougat Tutorial (Unlocked Retail Devices)
Prerequisites:
Download RSD lite XML to Batch Script from https://www.androidfilehost.com/?fid=24651430732235266
Download ROGERS_MPL24.246-45 from https://mega.nz/#!nssGEDiT!hhLkcTM106hmqbH_fiWfAytEV-fgdlYOhUwpcd_sGJY
Download Nougat firmware from https://mega.nz/#!608HGYqB!kKTc1196PhimDtVte6OdCWF6aXSWGSNLToEkvUePymE
Steps:
Unpack RSDLite XML to Batch Script to a folder on your computer
Unpack Rogers 24.246-45 firmware to the SAME folder
Run 2-rsd-flash-flashfile-windows.bat
Batch File #2 will convert the flashfile.xml file (included in Rogers zip) to a Batch file
Run flashfile.bat which will flash the Rogers firmware to your device (WILL WIPE EVERYTHING EXCEPT MICRO SD CARD)
Wait till its done!
Your device should now have Rogers 24.246-45 Firmware.
From the Bootloader, select Recovery Mode.
If you see No Command don't panic! That's normal. Press the power button for a couple seconds and press volume up or down (not sure if you need volume buttons but I always do anyway)
Once it displays on screen, Select ADB Sideload
From an adb capable command prompt, enter ADB Sideload <name and location of Nougat.zip> (minus the <> obviously)
This will take time. Leave it alone!
Once complete, simply reboot from recovery and let the device start like normal.
TROUBLESHOOTING:
If ADB Sideload gives you a Can't Read error, try these steps:
1. Download Large Address Awareness from here https://www.techpowerup.com/forums/threads/large-address-aware.112556/
2. Download ADB from here http://forum.xda-developers.com/showthread.php?t=2588979
3. Start Task Manager and kill adb.exe if its running
4. Load the adb.exe file from Large Address Awareness and check the flag button
5. Continue on with adb sideload
I've tested this process multiple times today and it should work well. Let me know if you have any trouble!
I want to mention I have had NO success backing up with TWRP and restoring after this. Something changed with Nougat and any modification to System causes a soft brick (it did for me anyway). Do not attempt to flash system mode TWRP or flash the TurboZ kernel. They don't work and they will cause a boot loop.
UPDATE:
This method might not be for everyone, and if you're not interested in sticking with stock 7.0 and potentially want to roll around to other ROMs you should follow this guide instead; http://forum.xda-developers.com/moto-z/development/android-nougat-moto-z-versions-t3506342

Great thank you! Question:
Will all the radio bands (T-MOBILE) still work as normal?
Have you try this out with Google Day Dream VR yet?
I had the note 7 and the Galaxy VR., Kinda of miss that.

dallas90733 said:
Great thank you! Question:
Will all the radio bands (T-MOBILE) still work as normal?
Have you try this out with Google Day Dream VR yet?
I had the note 7 and the Galaxy VR., Kinda of miss that.
Click to expand...
Click to collapse
Daydream works from what I can tell. Also I'm on att so I haven't checked T-Mobile bands but im assuming they work fine. I know there's an app to check which bands your device supports. I'll try downloading it and let you know

So I get to the point to sideload the nougat update and it always says "can't read..." I've done factory resets and everything else I could think of, still no go for me.

Prfndhatrdofman said:
...
I want to mention I have had NO success backing up with TWRP and restoring after this. Something changed with Nougat and any modification to System causes a soft brick (it did for me anyway). Do not attempt to flash system mode TWRP or flash the TurboZ kernel. They don't work and they will cause a boot loop.
Click to expand...
Click to collapse
So... are you of the opinion that recovering a Nougat boot+system TWRP backup on a MM phone would cause a soft brick too?
What type of soft brick do you faced exactly?

Prfndhatrdofman said:
Easy Flash to Nougat Tutorial (Unlocked Retail Devices)
Prerequisites:
Download RSD lite XML to Batch Script from https://www.androidfilehost.com/?fid=24651430732235266
Download ROGERS_MPL24.246-45 from https://mega.nz/#!nssGEDiT!hhLkcTM106hmqbH_fiWfAytEV-fgdlYOhUwpcd_sGJY
Download Nougat firmware from https://mega.nz/#!608HGYqB!kKTc1196PhimDtVte6OdCWF6aXSWGSNLToEkvUePymE
Steps:
Unpack RSDLite XML to Batch Script to a folder on your computer
Unpack Rogers 24.246-45 firmware to the SAME folder
Run 2-rsd-flash-flashfile-windows.bat
Batch File #2 will convert the flashfile.xml file (included in Rogers zip) to a Batch file
Run flashfile.bat which will flash the Rogers firmware to your device (WILL WIPE EVERYTHING EXCEPT MICRO SD CARD)
Wait till its done!
Your device should now have Rogers 24.246-45 Firmware.
From the Bootloader, select Recovery Mode.
If you see No Command don't panic! That's normal. Press the power button for a couple seconds and press volume up or down (not sure if you need volume buttons but I always do anyway)
Once it displays on screen, Select ADB Sideload
From an adb capable command prompt, enter ADB Sideload <name and location of Nougat.zip> (minus the <> obviously)
This will take time. Leave it alone!
Once complete, simply reboot from recovery and let the device start like normal.
I've tested this process multiple times today and it should work well. Let me know if you have any trouble!
I want to mention I have had NO success backing up with TWRP and restoring after this. Something changed with Nougat and any modification to System causes a soft brick (it did for me anyway). Do not attempt to flash system mode TWRP or flash the TurboZ kernel. They don't work and they will cause a boot loop.
Click to expand...
Click to collapse
I did up until this
From the Bootloader, select Recovery Mode.
If you see No Command don't panic! That's normal. Press the power button for a couple seconds and press volume up or down (not sure if you need volume buttons but I always do anyway)
Once it displays on screen, Select ADB Sideload
From an adb capable command prompt, enter ADB Sideload <name and location of Nougat.zip> (minus the <> obviously)
But when I boot up i have no wifi and I am unable to get the no command to go away to select sideload any ideas?

pieman13 said:
So I get to the point to sideload the nougat update and it always says "can't read..." I've done factory resets and everything else I could think of, still no go for me.
Click to expand...
Click to collapse
Same here, did you find a fix? Tried re-downloading Blur_Version.24.21.46.griffin.retail.en.US.zip and got the same error...

pixelens said:
Same here, did you find a fix? Tried re-downloading Blur_Version.24.21.46.griffin.retail.en.US.zip and got the same error...
Click to expand...
Click to collapse
This happened to me as well. I think it came down to being an ADB Driver issue for me. I reinstalled a different set of ADB drivers and it had no issue after that.

enetec said:
So... are you of the opinion that recovering a Nougat boot+system TWRP backup on a MM phone would cause a soft brick too?
What type of soft brick do you faced exactly?
Click to expand...
Click to collapse
Didn't work for me. As soon as the system partition was mounted R/W My device would boot loop. Could be a symptom of something else but im not sure.

Prfndhatrdofman said:
This happened to me as well. I think it came down to being an ADB Driver issue for me. I reinstalled a different set of ADB drivers and it had no issue after that.
Click to expand...
Click to collapse
Interesting... I'm using the adb drivers from Android Studio.
---------- Post added at 02:27 PM ---------- Previous post was at 02:16 PM ----------
Tried using the ADB drivers from Minimal ADB and Fastboot, same result. Oh well.

pixelens said:
Interesting... I'm using the adb drivers from Android Studio.
---------- Post added at 02:27 PM ---------- Previous post was at 02:16 PM ----------
Tried using the ADB drivers from Minimal ADB and Fastboot, same result. Oh well.
Click to expand...
Click to collapse
Yeah i struggled for about 3 hours trying to get sideload to work. I dunno why but after i completely deleted the driver, rebooted, reinstalled from ADB it finally worked. Its definitely not your device or the image its just ADB being a pain in the ass. I even tried multiple versions of ADB. One guy just tried on a different computer and it worked. I dunno why

Prfndhatrdofman said:
Yeah i struggled for about 3 hours trying to get sideload to work. I dunno why but after i completely deleted the driver, rebooted, reinstalled from ADB it finally worked. Its definitely not your device or the image its just ADB being a pain in the ass. I even tried multiple versions of ADB. One guy just tried on a different computer and it worked. I dunno why
Click to expand...
Click to collapse
Yah, I've had similar experiences in the past - been ages since I've done this though (Samsung Galaxy SII Skyrocket days) so just wanted to make sure I wasn't missing something.
Quick question though, title says "unlocked retail devices" - does that mean the bootloader has to be unlocked? Or will this work with a locked bootloader? Cheers.

pixelens said:
Yah, I've had similar experiences in the past - been ages since I've done this though (Samsung Galaxy SII Skyrocket days) so just wanted to make sure I wasn't missing something.
Quick question though, title says "unlocked retail devices" - does that mean the bootloader has to be unlocked? Or will this work with a locked bootloader? Cheers.
Click to expand...
Click to collapse
I specifically meant network unlocked. Really just any device purchased directly from Motorola.
But yeah i think you might need to have an unlocked bootloader as well.

pixelens said:
Same here, did you find a fix? Tried re-downloading Blur_Version.24.21.46.griffin.retail.en.US.zip and got the same error...
Click to expand...
Click to collapse
Fix was I went back to my pixel and sold the Z.

Mine has unlocked bootloader. Unlocked thru Motorola's website since the first hour I got it

Got the Nougat update to sideload (yay!) - tried a different computer that had no adb drivers installed, used the ones from Minimal ADB and Fastboot and they worked no problem.
Is it possible to lock the bootloader after the Nougat update? I tried and received "(bootloader) still require signed boot.img" message.

pixelens said:
Got the Nougat update to sideload (yay!) - tried a different computer that had no adb drivers installed, used the ones from Minimal ADB and Fastboot and they worked no problem.
Is it possible to lock the bootloader after the Nougat update? I tried and received "(bootloader) still require signed boot.img" message.
Click to expand...
Click to collapse
Dunno. I get the same error.

Thank you for this guide!

Prfndhatrdofman said:
Easy Flash to Nougat Tutorial (Unlocked Retail Devices)
Prerequisites:
Download RSD lite XML to Batch Script from https://www.androidfilehost.com/?fid=24651430732235266
Download ROGERS_MPL24.246-45 from https://mega.nz/#!nssGEDiT!hhLkcTM106hmqbH_fiWfAytEV-fgdlYOhUwpcd_sGJY
Download Nougat firmware from https://mega.nz/#!608HGYqB!kKTc1196PhimDtVte6OdCWF6aXSWGSNLToEkvUePymE
Steps:
Unpack RSDLite XML to Batch Script to a folder on your computer
Unpack Rogers 24.246-45 firmware to the SAME folder
Run 2-rsd-flash-flashfile-windows.bat
Batch File #2 will convert the flashfile.xml file (included in Rogers zip) to a Batch file
Run flashfile.bat which will flash the Rogers firmware to your device (WILL WIPE EVERYTHING EXCEPT MICRO SD CARD)
Wait till its done!
Your device should now have Rogers 24.246-45 Firmware.
From the Bootloader, select Recovery Mode.
If you see No Command don't panic! That's normal. Press the power button for a couple seconds and press volume up or down (not sure if you need volume buttons but I always do anyway)
Once it displays on screen, Select ADB Sideload
From an adb capable command prompt, enter ADB Sideload <name and location of Nougat.zip> (minus the <> obviously)
This will take time. Leave it alone!
Once complete, simply reboot from recovery and let the device start like normal.
I've tested this process multiple times today and it should work well. Let me know if you have any trouble!
I want to mention I have had NO success backing up with TWRP and restoring after this. Something changed with Nougat and any modification to System causes a soft brick (it did for me anyway). Do not attempt to flash system mode TWRP or flash the TurboZ kernel. They don't work and they will cause a boot loop.
Click to expand...
Click to collapse
Hello
I flashed the rogers 45 firmware, but when I go to recovery mode I can't get the ADB menu to appear. I've held power and down, power and up, nothing, etc. Am I missing something? I did the rogers install, then went to homescreen, then powered off.
EDIT
after restarting my phone like 10 times in 5 minutes (rest in peace...) I finally figured it out. Now my issue is that I can't seem to get the sideload to work. I am going to try uninstalling android studio and start again. Did you guys figure out why it says * cannot read ' blur.....' * ?

I found how to fix the adb problem about being unable to read from another thread on XDA
1. Download Large Address Awareness from here https://www.techpowerup.com/forums/threads/large-address-aware.112556/
2. Download ADB from here http://forum.xda-developers.com/showthread.php?t=2588979
3. Start Task Manager and kill adb.exe if its running
4. Load the adb.exe file from Large Address Awareess and check the flag button
5. Continue on with adb sideload
---------- Post added at 09:42 AM ---------- Previous post was at 09:40 AM ----------
Porcelainfog said:
Hello
I flashed the rogers 45 firmware, but when I go to recovery mode I can't get the ADB menu to appear. I've held power and down, power and up, nothing, etc. Am I missing something? I did the rogers install, then went to homescreen, then powered off.
Click to expand...
Click to collapse
Do you see the "No command" picture after choosing Recover Mode? Once you get to that, I hold down power and tap volume up and down again and again

ROOT NOKIA 3 TA-1032 Android 8.0

Hi !
I tried to root my Nokia 3 TA-1032 with Android Oreo following the instructions on supersu.com/gettingstarted#recovery
My problem is that I can't access to recovery mode and don't know how to activate it. How can i access it ? Or have you an another simplest way to root it ?
Thanks

>Taps< said:
Hi !
I tried to root my Nokia 3 TA-1032 with Android Oreo following the instructions on supersu.com/gettingstarted#recovery
My problem is that I can't access to recovery mode and don't know how to activate it. How can i access it ? Or have you an another simplest way to root it ?
Thanks
Click to expand...
Click to collapse
What about adb reboot recovery?

redweaver said:
What about adb reboot recovery?
Click to expand...
Click to collapse
Hi !
I will try adb and reply after it.

anybuddy please help me my Nokia 3 android 8.0 I am trying to unlock bootloader in fastboot mode but fastboot command window always give me error wrong command I tried almost commands like fastboot oem unlock, I 2x0b4ed oem unlock, fastboot oem unlock codekey etcs but always keep getting massage wrong command I already enabled usb debugging and unlock oem in developers option I have ta1032 model.

redweaver said:
What about adb reboot recovery?
Click to expand...
Click to collapse
Ok, so, adb reboot recovery don't work, it just normaly reboot the phone.
How can i fix it ?

>Taps< said:
Ok, so, adb reboot recovery don't work, it just normaly reboot the phone.
How can i fix it ?
Click to expand...
Click to collapse
I hope you didn't unplug your phone from your PC when rebooting. Phone has to be plugged in to enter recovery

I hadn't unplug my phone during the reboot

>Taps< said:
I hadn't unplug my phone during the reboot
Click to expand...
Click to collapse
or you can use usual method:
connect phone to charger/PC and turn off your phone. Hold power + vol up button and counting will begin. When counting ends, hold for 2 sec more and it should boot to recovery.

SkaboXD said:
or you can use usual method:
connect phone to charger/PC and turn off your phone. Hold power + vol up button and counting will begin. When counting ends, hold for 2 sec more and it should boot to recovery.
Click to expand...
Click to collapse
Yes but it doesn't work I have the error "No command" I tried also power +vol - but it's just the fastboot mode.

>Taps< said:
Yes but it doesn't work I have the error "No command" I tried also power +vol - but it's just the fastboot mode.
Click to expand...
Click to collapse
When you get to the no command screen you have to press power + volume up. There's a trick to it, I don't get it all the time either.

redweaver said:
When you get to the no command screen you have to press power + volume up. There's a trick to it, I don't get it all the time either.
Click to expand...
Click to collapse
I just tried and it worked I arrived in the recovery mode but I did not find " install" ?

>Taps< said:
I just tried and it worked I arrived in the recovery mode but I did not find " install" ?
Click to expand...
Click to collapse
What exactly are you trying to install?
One other thing, if you want to root your phone on Oreo, this is the way to go:
https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768

redweaver said:
What exactly are you trying to install?
One other thing, if you want to root your phone on Oreo, this is the way to go:
https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768
Click to expand...
Click to collapse
Ok I will try it and reply after

>Taps< said:
Yes but it doesn't work I have the error "No command" I tried also power +vol - but it's just the fastboot mode.
Click to expand...
Click to collapse
I too got same no command on my phone too, try this it will work 99% press power and volume+ same time then Nokia logo flash just release power button only not volume+ you will enter on no command screen then now the trick is to press both button at same time volume+ and power for 2-3 sec release buttons again press both buttons and release do this simultaneously you will get into recovery mode.

redweaver said:
What exactly are you trying to install?
One other thing, if you want to root your phone on Oreo, this is the way to go:
https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-flash-twrp-magisk-t3785768
Click to expand...
Click to collapse
Ok,I tried the flash way and tried the two different steps :
For the one - Step 2,
*I'm blocked, I don't know when start the phone, click on download... and sometimes i have an error about the authentication file
For the two -Step 2
*Magisk Manager don't want to download zip and create patched boot image. Nothing happens
I really don't know.

>Taps< said:
Ok,I tried the flash way and tried the two different steps :
For the one - Step 2,
*I'm blocked, I don't know when start the phone, click on download... and sometimes i have an error about the authentication file
For the two -Step 2
*Magisk Manager don't want to download zip and create patched boot image. Nothing happens
I really don't know.
Click to expand...
Click to collapse
This is how I do mine, click on download, then if the phone is on, shut it down. It doesn't always work but sometimes it does. You have to finish that step before the next.
What version of spflashtool did you download?

redweaver said:
What version of spflashtool did you download?
Click to expand...
Click to collapse
I use the version 5.1804.
redweaver said:
This is how I do mine, click on download, then if the phone is on, shut it down. It doesn't always work but sometimes it does. You have to finish that step before the next.
Click to expand...
Click to collapse
What's next ?

>Taps< said:
I use the version 5.1804.
What's next ?
Click to expand...
Click to collapse
Did the progress bar change? If not try unplugging your phone then plugging it back. If that doesn't work, start the phone again and shutdown
By the way what did you try to flash?

I didn't see any bar progress ??*
I want to flash TWRP to install magisk or supersu

>Taps< said:
I didn't see any bar progress ??*
I want to flash TWRP to install magisk or supersu
Click to expand...
Click to collapse
So the download button is still greyed out? Start phone and try again

I really screwed up flashing a rom. PLZ HELP.

Hi y'all
So I was flashing my oneplus 7 pro with pixel experience.
To do it I followed a guide by get droid tips ( i cant post the link this is my first post.)
But now my oneplus is stuck on the google logo and if I go into recovery mdoe I get a message saying no command.
I also get the bootloader is unlocked message before booting up, but nothing happens if press the power button.

Use MSM download tool

I honestly have no idea what to tell you for that specific situation BUT you can always use the tool-all-in-one for op7pro and flash oos back to stock OR use the tool to boot twrp then flash OOS from there
Sent from my OnePlus7Pro using XDA Labs

RicardoDimm said:
Use MSM download tool
Click to expand...
Click to collapse
Do you have a guide i could use

spart0n said:
I honestly have no idea what to tell you for that specific situation BUT you can always use the tool-all-in-one for op7pro and flash oos back to stock OR use the tool to boot twrp then flash OOS from there
Sent from my OnePlus7Pro using XDA Labs
Click to expand...
Click to collapse
My pc can't recognize my phone.

Download here: https://forums.oneplus.com/threads/...ide-for-a-hard-bricked-oneplus-7-pro.1041896/
Start tool on PC
Turn phone off. Hold volume up & down at the same time, then connect phone to PC.
Press start in the tool and the tool does is all for you.

RicardoDimm said:
Download here: https://forums.oneplus.com/threads/...ide-for-a-hard-bricked-oneplus-7-pro.1041896/
Start tool on PC
Turn phone off. Hold volume up & down at the same time, then connect phone to PC.
Press start in the tool and the tool does is all for you.
Click to expand...
Click to collapse
I tried it but my pc doesn't recognize my phone at all.

RicardoDimm said:
Download here: https://forums.oneplus.com/threads/...ide-for-a-hard-bricked-oneplus-7-pro.1041896/
Start tool on PC
Turn phone off. Hold volume up & down at the same time, then connect phone to PC.
Press start in the tool and the tool does is all for you.
Click to expand...
Click to collapse
Are you sure you meant Volume up AND down, not volume up and the power button.

Does Adb working?
Sent from my GM1911
---------- Post added at 06:21 PM ---------- Previous post was at 06:20 PM ----------
I had an issue and i booted twrp img via adb
Sent from my GM1911

In your situration, I would do the following: (assuming you're on Windows)
Install Android USB driver from: https://developer.android.com/studio/run/win-usb and install them
Download the the platform tools: https://developer.android.com/studio/releases/platform-tools and put them into a folder somewhere
Boot your phone to the bootloader by turning it off (make sure it's turned off) then press volume up and volume down at the same time until you get into the bootloader screen, then release them both. EDIT: press the power button as well to turn it on.
Open the folder where you put the platform tools you downloaded earlier. Make sure you have a file named fastboot(.exe) in there, if not find it. Hold the shift key on your keyboard and then right click in an empty space in the window (not on a file or folder) and click open command prompt here.
In the command prompt type 'fastboot devices' (without the quotes) and see if your phone is listed, it should be. If not, go to device manager (right click on the windows icon in the bottom left corner -> device manager) and find an Android or something like Unknown device and try to install the USB driver for it.
When your phone is listed by fastboot, then you're good. Download TWRP from here: https://twrp.me/oneplus/oneplus7pro.html and put the .img file in the same folder as your platform tools and rename the file to recovery.img
EDIT: correction:
redpoint73 said:
You need to fastboot boot TWRP.img. From there, you can flash the TWRP installer zip (reference instruction from the TWRP developer here: https://forum.xda-developers.com/on...nt/recovery-unofficial-twrp-recovery-t3931322).
Click to expand...
Click to collapse
At this point you download a ROM, put it on your phone and flash it. If it doesn't boot, you will probably have to perform a factory reset in TWRP and loose your data.

First, don't panic and breath. Panicking is what causes mistakes and can make the problem more stressful.
Second, more than likely, the reason your PC can't recognize it is because of drivers. You want to ensure you remove previous drivers and install fresh ones. The Qualcomm drivers can be found in the unbrick tool thread that was listed above. With that, your PC should be able to see your phone from there.

QUBiCA said:
In your situration, I would do the following: (assuming you're on Windows)
Install Android USB driver from: https://developer.android.com/studio/run/win-usb and install them
Download the the platform tools: https://developer.android.com/studio/releases/platform-tools and put them into a folder somewhere
Boot your phone to the bootloader by turning it off (make sure it's turned off) then press volume up and volume down at the same time until you get into the bootloader screen, then release them both.
Open the folder where you put the platform tools you downloaded earlier. Make sure you have a file named fastboot(.exe) in there, if not find it. Hold the shift key on your keyboard and then right click in an empty space in the window (not on a file or folder) and click open command prompt here.
In the command prompt type 'fastboot devices' (without the quotes) and see if your phone is listed, it should be. If not, go to device manager (right click on the windows icon in the bottom left corner -> device manager) and find an Android or something like Unknown device and try to install the USB driver for it.
When your phone is listed by fastboot, then you're good. Download TWRP from here: https://twrp.me/oneplus/oneplus7pro.html and put the .img file in the same folder as your platform tools and rename the file to recovery.img
In the command prompt you have open, type, again without the quotes 'fastboot flash recovery recovery.img'. When that's done you should have TWRP installed and working.
At this point you download a ROM, put it on your phone and flash it. If it doesn't boot, you will probably have to perform a factory reset in TWRP and loose your data.
Click to expand...
Click to collapse
After holding the volume and down buttons for about a minute, the bootloader didnt pop up.

QUBiCA said:
[*]In the command prompt you have open, type, again without the quotes 'fastboot flash recovery recovery.img'. When that's done you should have TWRP installed and working.
Click to expand...
Click to collapse
This is not the correct way to install TWRP on this device. You need to fastboot boot TWRP.img. From there, you can flash the TWRP installer zip (reference instruction from the TWRP developer here: https://forum.xda-developers.com/on...nt/recovery-unofficial-twrp-recovery-t3931322).
This phone does not even have a recovery partition to which your command is trying to flash the img to (recovery resides on boot.img partition on this device).
---------- Post added at 09:53 AM ---------- Previous post was at 09:49 AM ----------
taransingh2001 said:
After holding the volume and down buttons for about a minute, the bootloader didnt pop up.
Click to expand...
Click to collapse
With power off, hold vol up and vol down, and then hold power button. The phone should boot to bootloader after several seconds.

redpoint73 said:
This is not the correct way to install TWRP on this device. You need to fastboot boot TWRP.img. From there, you can flash the TWRP installer zip (reference instruction from the TWRP developer here: https://forum.xda-developers.com/on...nt/recovery-unofficial-twrp-recovery-t3931322).
This phone does not even have a recovery partition to which your command is trying to flash the img to (recovery resides on boot.img partition on this device).
Click to expand...
Click to collapse
Made some edits, thanks! I blindly assumed it would be the same as with my previous OnePlus 3T.

QUBiCA said:
Made some edits, thanks! I blindly assumed it would be the same as with my previous OnePlus 3T.
Click to expand...
Click to collapse
Thanks for correcting your previous post. I came from the 3T as well. A lot has changed (with the 7 Pro) due to the A/B partition scheme.