hi,
i was using garmin vivosmart HR for my training, the screen was always on so i could watch over my pulse.
now with the Gear S3 i can see my pulse during training if i start a s-health training and i also got the HR application from the samsung store but both cannot override the watch configuration and always stay on.
if i choose always on, when my hand is on the eliptical (where i run) the watch shows the watch face, not the HR.
only if i get my hand up - i see the HR.
any hack for this?
There is an app called: I am alive. It let's you to keep the display on. Battery drainer though.
While I had my my AT&T S3 Frontier LTE watch set to "Always On" I was getting something like a "Screensaver" which consisted of just the hour and minutes hands in white on a black background. It came on after the watch display dimmed and after the display time out. This happened while using the Chronograph+ (default) watch face. It was a distinctive + useful screen face that probably saved me some battery life. Now the displays dims after the time out and then it turns completely off (black). After I power cycled the S3 yesterday, I stopped getting this "Screensaver" and can't find the settings combination that will get this "screensaver" back. Does anyone know what I'm talking about and how to get it back?
tamanaco said:
While I had my my AT&T S3 Frontier LTE watch set to "Always On" I was getting something like a "Screensaver" which consisted of just the hour and minutes hands in white on a black background. It came on after the watch display dimmed and after the display time out. This happened while using the Chronograph+ (default) watch face. It was a distinctive + useful screen face that probably saved me some battery life. Now the displays dims after the time out and then it turns completely off (black). After I power cycled the S3 yesterday, I stopped getting this "Screensaver" and can't find the settings combination that will get this "screensaver" back. Does anyone know what I'm talking about and how to get it back?
Click to expand...
Click to collapse
Enable Settings -> Style -> Watch Always On
tamanaco said:
While I had my my AT&T S3 Frontier LTE watch set to "Always On" I was getting something like a "Screensaver" which consisted of just the hour and minutes hands in white on a black background. It came on after the watch display dimmed and after the display time out. This happened while using the Chronograph+ (default) watch face. It was a distinctive + useful screen face that probably saved me some battery life. Now the displays dims after the time out and then it turns completely off (black). After I power cycled the S3 yesterday, I stopped getting this "Screensaver" and can't find the settings combination that will get this "screensaver" back. Does anyone know what I'm talking about and how to get it back?
Click to expand...
Click to collapse
I don't think I've really ever used the default faces. I know in a lot of the Watchmaker faces you can get a toned down face with maybe just the numbers and hands glowing when using AOD mode but I don't know about the default faces. In display settings there's a setting for auto low brightness that may affect that.
10urshin said:
Enable Settings -> Style -> Watch Always On
Click to expand...
Click to collapse
If you read the first sentence of my post you'd see that I'm already using this setting.
tamanaco said:
If you read the first sentence of my post you'd see that I'm already using this setting.
Click to expand...
Click to collapse
Yea i have read it. Not just first sentence but I also read the whole thing, you must admit it is not really making much sense. "Screensaver"? There is no such thing on this watch, only AOD and "Now the displays dims after the time out and then it turns completely off (black)." this sentence perfectly describes the AOD off behavior. So i thought it worth mentioning.
Only other thing that comes to my mind is default analog AOD watchface(attachment) which is something watch shows if the current watchface does not support AOD. But since you stated that you were getting your "screensaver" on Chronograph+ which supports AOD, it doesn't really make sense either.
Anyway hope you'll find your answer.
I also saw this "screensaver" mode in a review video somewhere, but I have not been able to locate it again. Once I find it, I'll post a screenshot of it.
tamanaco said:
While I had my my AT&T S3 Frontier LTE watch set to "Always On" I was getting something like a "Screensaver" which consisted of just the hour and minutes hands in white on a black background. It came on after the watch display dimmed and after the display time out. This happened while using the Chronograph+ (default) watch face. It was a distinctive + useful screen face that probably saved me some battery life. Now the displays dims after the time out and then it turns completely off (black). After I power cycled the S3 yesterday, I stopped getting this "Screensaver" and can't find the settings combination that will get this "screensaver" back. Does anyone know what I'm talking about and how to get it back?
Click to expand...
Click to collapse
Thinking more about it, I don't think the AOD is even supposed to remain on all the time. That has been a major complaint, the AOD mode not being actually AOD. What you're experiencing now isn't normal and there should be no setting to change that. If you want to set up the watch again, you might try resetting it. That's assuming you've already tried just restarting it.
What comes to my mind with "Watch always on" (or "Always On Display", AOD) and having screen completely black is if watch thought at some point that you weren`t wearing it - only in that case should the screen go completely black with AOD set, otherwise it should, well, keep "always on display", that`s the point of the setting
When you take the watch off your hand, then it goes blank even though AOD setting is still active - watch is "playing it smart" to preserve battery life in case where you`re not actively using it.
But, it`s possible for the watch to (wrongly) think that you`re not wearing it even when you do, thus turning the screen off when it should otherwise be in AOD mode (as set). For example, it can happen when your wrist band is a bit loose so the heart rate sensor has issues reading your pulse, or when the heart rate sensor itself is smudgy or otherwise blocked to make the valid reading - some people with tattoos reported that AOD doesn`t really work for them, having the screen constantly turning off (tattoo effectively confusing the heart rate sensor reading).
This is especially troublesome if you`re using "Samsung Pay", where the watch asks for you PIN in order to unlock itself every-single-time, as it`s thinking that you didn`t wear it in the meantime...
All this said, from what you described, it looks like AOD doesn`t work for you at all anymore, as what you seem to call "Screensaver" is actually AOD - a dimmed and more simple version of the watch, whose main purpose is to spare the battery while still providing a bit more realistic feel, having the watchface shown all the time.
There is additional "trick" to trigger AOD mode (once you have the setting configured), besides simply waiting for some (configured) time to pass by - just cover the watch with your palm for a few seconds, and it should fall back to AOD mode. If the screen goes blank instead, you might have an issue with the watch.
It would be good to have some default watchface in use when you`re trying AOD (like mentioned Chronograph+), just to opt out a possibly "broken" third-party watchface, and you could also check if "S Health" heart-rate reading works for you, starting a heart-rate readout manually (you can use a widget for that as well).
If the issue is still there, you may try restarting the watch again, or eventually soft (or factory) resetting might be a thing to go for, too, though you`ll have to setup the watch again, as already mentioned.
I have seen the exact same behavior. My AOD will suddenly become black and white, while normally it is full color, and any app icons that are usually on the AOD disappear. When the watch is active (by turning wrist or touching the screen), the full color face returns and looks normal - it is only the AOD that is always B&W. The difference for me is that I don't like it and I would like to figure out how to get it to stop happening.
I've had the watch for about 2 months and it has happened to me 3 times with different watch faces. It lasts from several hours to more than a day. I have changed every related face setting, changed faces, changed face settings, AOD settings, restarted, and reset the watch completely (and restore), but it still happens. The only thing that I've noticed may help (may be coincidence) is that it will stay indefinitely until I power cycle the watch. After restarting, the AOD remains black and white for a few hours and then suddenly the color AOD will return. Next time it happens I will take a pic.
I'm actually somewhat relieved that I'm not the only one who has seen this because my googling revealed next to nothing. I don't know if I would call this a screensaver, but it would be nice to be able to control it.
annulation said:
I'm actually somewhat relieved that I'm not the only one who has seen this because my googling revealed next to nothing. I don't know if I would call this a screensaver, but it would be nice to be able to control it.
Click to expand...
Click to collapse
I knew I was not seeing things... please take a picture if it happens again, so that we can have a reference image. I'll do the same if it happens to me again. In certain situations... I actually like just having the hour and minute hands in "brightish" white on black background. Like you, I would also like to control it. I thought it was a "screensaver-like" feature as the watch face turns mostly black. But as you say, it might be a glitch... it has not happened to me since I last power cycled the S3.
Low Color AOD
I finally figured it out.
The behavior is called "Low Color AOD" and "High Color AOD". It is controllable by swiping from the right side of the screen near 5 o'clock straight up. This consistently toggles it for me, and a popup message shows a message saying either "Low Color AOD" or "High Color AOD". See pics attached (sorry, don't know how to rotate them).
Pics:
1. Low Color AOD
2. High Color AOD
3. popup message Low Color AOD
4. popup message High Color AOD
Only some faces support this behavior. For me, "Low Color AOD" always means monochrome B&W and no app icons.
PS - this face is called "Stylish Set" and the creator gives free coupons for it if you email him. It is one of the few faces I've found that shows day/date, with temperature and battery.
As mentioned, the function described is dependent on the functionality of each watch face independent of the watch itself. If a given watch face supports it, it can be accessed. The "always on" function also depends on the capabilities of each watch face. Some have customized always on displays, and some do not (generic). The watch will go black if it senses it is not against the skin (the sensor on the back). This will also cause the watch to lock again and require the security code to re-activate. If a band is too loose, the watch can falsely think it has been taken off. The time that the watch face itself is on can be extended with an app called "Flaunt" available from the Galaxy app store. It can extend the original watch face active time to 30 minutes. It can then be re-activated to extend for other 30 minute time periods. Of course it does impact the battery life.
Hi all,
Since last week i bought the gear sport. It's a nice watch and keeps good track.
There is only one thing i find strange is that when i start
t an activity,after some seconds it goes back to the default clock. I have to press an button or wind the gear to show the statistics.
How can I make sure the activity is shown instead of the clock? I already set the display to be on, and the timeout to 5 minutes.
Help would be appreciated
I want to switch from my Moto 360 because when I use StayLit Wear to set the display to remain indefinitely on, the battery drains completely in three hours. I want a smartwatch with a display lit constantly (with automatic brightness, so it's bright enough to be visible in daylight and dim enough to not attract attention in darkly lit environments) that can still last me 24 hours, running the default watch face.
I use a Bluetooth headset connected to my phone to attend to calls all day long and I want the watch primarily to show me the time, alert me to calls and look good while doing it. I'll try to use the health stuff and the sleep tracking and the notifications, but they're not terribly important. Can I get that from the Samsung Gear S3 Frontier (with the latest battery draining update installed)?
Upon doing some Googling, I found that the watch face will dim after a specific timeout even with AOD enabled, and that I need to install either Flaunt or I Am Alive to get it to truly remain always on. So I guess my question is, with the display set to always on via either of these apps, can I expect it to last me a full day of use?
Yes the AOD dims but is still readable and depending on the watchface still quite bright. The watch has auto low light and auto outside modes to cover the extremes. With the wrist gestures, the watch brightens to your set brightness. I don't think you would be disappointed. The battery still gives me a full day 05.15 - 22.00 with 25-30% left with Tizen 3.0.0.2
I got a question. On my old Gear S3 when i enabled auto workout detection and started running, after 10 minutes my watch said "Keep it up!" And i could track how long i was running and stuff. Is there a way to have this on my Watch 4? Cause it does auto track my workouts but i cannot track em trough my watch and it does not pop up after running for 30minuted and stuff while i'm exercising. Thanks for the help!
Nobody?
I was using this option long time ago. If I remember well you can switch on Auto detect Activities in Settings - Samsung Health . Watch detects only walking and running, after ~10 minutes. Tracking screen should pop up or there will be small Activiti icon at screen bottom. Just touch it to see full tracking.