Hi all,
I have a OnePlus One that's hardbricked (it doesn't show any forms of life).
I followed this guide, but I'm stuck. I installed QPST Drivers, and Qualcomm 2012 Drivers (although after installing this one, I get a message stating that the newest drivers are already installed.).
At the moment, my device is recognized in device manager as "Qualcomm HS-USB- QDLoader 9008 (COM10)" and sometimes it doesn't get recognized at all. The device manager will then say "unknown device".
When the device is recognized as "Qualcomm HS-USB- QDLoader 9008 (COM10)", it doesn't get recognized by the OnePlusRestoreTool (even if I run it in administrator mode).
I'm using Windows 7.
Could any of you perhaps help me find a solution?
Thanks in advance!
Robert
Related
Hello OPO owners.
I need some help in unbricking my device. I followed the tutorial with color.zip. Driver installation went without problem device manager showed as QDloader 9008 and msm8974downloadtool recognized the device and started flashing. so far no problem.
Problems start after device change to Qualcomm HS-USB Diagnostics 9006 (as it should be). in this state my OPO seems to "disconnect" every 8-10 seconds. in msm8974downloadtool and device manager it disappears for about half a second and the reappears for another 8 seconds. So the tool starts flashing and by the time it reaches system.img disconnect and the flashing starts again. kind of a bootloop
already tried different cables, usb-ports, computers (win 7 and win xp) without success. the disconnecting only appears in 9006 state, in 9008 state all is good.
any idea is welcome
Try this thread:
http://forum.xda-developers.com/one...overy-tool-v1-0-restore-t2991851/post57934891
tropenfrucht said:
Hello OPO owners.
I need some help in unbricking my device. I followed the tutorial with color.zip. Driver installation went without problem device manager showed as QDloader 9008 and msm8974downloadtool recognized the device and started flashing. so far no problem.
Problems start after device change to Qualcomm HS-USB Diagnostics 9006 (as it should be). in this state my OPO seems to "disconnect" every 8-10 seconds. in msm8974downloadtool and device manager it disappears for about half a second and the reappears for another 8 seconds. So the tool starts flashing and by the time it reaches system.img disconnect and the flashing starts again. kind of a bootloop
already tried different cables, usb-ports, computers (win 7 and win xp) without success. the disconnecting only appears in 9006 state, in 9008 state all is good.
any idea is welcome
Click to expand...
Click to collapse
I used the LG Flash Tool 2014 for my device to try to recover from a bricked phone. And I think i made it worse after using the kdz file and it completed 100%. I took the battery out and unplugged the phone when it was done. It wont even show anything on the screen now or go into recovery mode. But I do show RELINK HS-USB QDLoader 9008 (COM5) under the device options in my device manager when I connect the phone to the computer. Also it does make the device connected sound when I plug it in the computer. What can I do to get out of this mess? Thanks in the advance for any help that I can get.
Any help will be appreciated. THanks.
[Q] Bricked. Erased/messed up bootloader. Win recognized as "HS-USB QDLoader 9008".
Hello.
Finally I hard bricked my Photon Q. I think I erased an unlocked bootloader. Right now phone cannot boot into fastboot mode. Power+Vol up, Power+Vol down held long do nothing. After connecting to Windows PC, phone is recognized as "HS-USB QDLoader 9008". I found drivers on the net. RSDlite recognizes device, but flashing fails with message that it cannot switch phone from download mode. I found QPST service software used to flash bootloader. Right now I think the problem is that I don't have proper bootloader images for Photon Q, and to be honest, I don't really know what options to use (the software seems quite complicated).
Has anyone encoutered (and solved) similar issues? Do you have any ideas, what to do? I tried some generic Qualcomm files, but couldn't flash them.
Anyone, please, help me, if you can.
Chris
Hello everyone,
When flashing stock firmware, my phone suddenly went non-responsive during the reboot and now it seems to be bricked pretty bad. When looking in the device manager, the only weird thing I see is that the device is coming up as Qualcomm HS-USB QDLoader 9006.
From what I have seen, I need a package called an EMMC, but I have no idea where to get that. Does anyone have any suggestions for me?
I get no response, no bootloader, no logo, no recovery, and buttons do not work. I have other Razer 2 devices to test from to get this working and will do any suggestions to unbrick this device.
thank you,
SITUATION:
hello , My phone is an asus x014d. recently I switched it off , and it just would not boot up again.
when i press the power on button it shows "powered by android" then the "asus" logo.
PROBLEMS:
- I CANNOT ENTER RECOVERY MODE (by doing the power on + vol up)
- I CANNOT ENTER TO FASTBOOT
- Device manager only identifies device as "qualcomm hs-usb diagnostics 9006" instead of "qualcomm hs-usb diagnostics 9008"
- when QFIL for unbricking it yields error "sahara fail"
- when using eMMC software Download the errors i get are "timeout waiting" , box dialog "cookie(if present) not received"
- managed to get into qualcomm hs-usb diagnostics 9008 mode but i can only manage to do that after getting to 9006 then flashing stock rom with RAW HDD TOOL then i am able to get into 9008.
TL;DR - DESCRIPTION (**NOOB ALERT**)
after research , i found out that my phone is bricked. i learnt that i have to get my phone identified by the computer through the "qualcomm usb drivers" then flash through "QFIL" a tool used for unbricking devices that have qualcomm processors.
i was able to successfully install the drivers , and plug my phone to the pc it shows that it is charging so i press the power plus volume up , then phone switches off and device manager never shows me the "qualcomm hs-usb diagnostics 9008" unless after switching off i immediately press volume down then device manager shows me "qualcomm hs-usb diagnostics 9006".
QPST will not flash the device if it is on "qualcomm hs-usb diagnostics 9006" so i learnt how to format the eMMC with raw HDD tool and whenever i formatted the eMMC with the stock rom , the pc would identify the device under PORTS > "qualcomm hs-usb diagnostics 9008"
when using QPST i am given the error "sahara fail" , and when using eMMC software downloader i get the error "cookie not received" and sometimes timeout.
i cannot attempt to get my phone to revive my phone (it sticks on a logo and when it is completely off and plugged in it shows a battery charging animation).
- any insight on how to solve this?
- Is it a Software issue that can be solved without the intervention of hardware? is my issue strictly a hardware issue? (e.g malfunctioning logic board)?
i am ready to provide images and files or any further clarification if needed.
any help or guide into this issue would be greatly appreciated thanks for investing time into helping me and others.
AdelTheConfused said:
SITUATION:
hello , My phone is an asus x014d. recently I switched it off , and it just would not boot up again.
when i press the power on button it shows "powered by android" then the "asus" logo.
PROBLEMS:
- I CANNOT ENTER RECOVERY MODE (by doing the power on + vol up)
- I CANNOT ENTER TO FASTBOOT
- Device manager only identifies device as "qualcomm hs-usb diagnostics 9006" instead of "qualcomm hs-usb diagnostics 9008"
- when QFIL for unbricking it yields error "sahara fail"
- when using eMMC software Download the errors i get are "timeout waiting" , box dialog "cookie(if present) not received"
- managed to get into qualcomm hs-usb diagnostics 9008 mode but i can only manage to do that after getting to 9006 then flashing stock rom with RAW HDD TOOL then i am able to get into 9008.
TL;DR - DESCRIPTION (**NOOB ALERT**)
after research , i found out that my phone is bricked. i learnt that i have to get my phone identified by the computer through the "qualcomm usb drivers" then flash through "QFIL" a tool used for unbricking devices that have qualcomm processors.
i was able to successfully install the drivers , and plug my phone to the pc it shows that it is charging so i press the power plus volume up , then phone switches off and device manager never shows me the "qualcomm hs-usb diagnostics 9008" unless after switching off i immediately press volume down then device manager shows me "qualcomm hs-usb diagnostics 9006".
QPST will not flash the device if it is on "qualcomm hs-usb diagnostics 9006" so i learnt how to format the eMMC with raw HDD tool and whenever i formatted the eMMC with the stock rom , the pc would identify the device under PORTS > "qualcomm hs-usb diagnostics 9008"
when using QPST i am given the error "sahara fail" , and when using eMMC software downloader i get the error "cookie not received" and sometimes timeout.
i cannot attempt to get my phone to revive my phone (it sticks on a logo and when it is completely off and plugged in it shows a battery charging animation).
- any insight on how to solve this?
- Is it a Software issue that can be solved without the intervention of hardware? is my issue strictly a hardware issue? (e.g malfunctioning logic board)?
i am ready to provide images and files or any further clarification if needed.
any help or guide into this issue would be greatly appreciated thanks for investing time into helping me and others.
Click to expand...
Click to collapse
Try with official ASUS drivers or, try to use the com port mounted on the back of the motherboard, maby.. i wouldnt suggest it to use to com port. it would require some hardware knowledge