Credit goes to eugene373 and attn1. These are mostly their instructions, but I did change, clarify, and add a few steps. If you can't get any of the other methods working, try this one.
Prerequisites...
Note: If you're in Linux, you only need to do Step 4, Step 6, and Step 7.
Step 0.
Download and install HTC Sync: http://www.htc.com/us/support/aria-att/downloads/
Step 1.
Download and unzip the Android SDK: http://developer.android.com/sdk/index.html
Step 2.
Go into the folder where you unzipped the Android SDK and open "SDK Setup.exe".
If you aren't greeted with a failed to fetch URL error, proceed to Step 3. If you did receive this error, go to Settings in the "Choose Packages to Install" window and check "Force https;//... sources to be fetched using http://..."
Close and re-open "SDK Setup.exe".
Step 3.
When the "Choose Packages to Install" window pops up, make sure the package "Usb Driver package, revision x" is checked. You can uncheck everything else. Click Install. After it downloads and installs, close "Android SDK and AVD Manager".
Step 4.
With your device unplugged from your computer, go to Settings > Application > Development on your device and turn on USB Debugging.
Step 5.
Now plug your device in to your computer. This is just to make sure the USB drivers are installed.
Once they are installed, unplug your device and turn it off.
Step 6.
This step is optional, but it may prevent an error later on in the process. If you've never formatted your SD card from a computer, remove it from the phone and format it in Windows or OSX with an external card reader. Then place the formatted card back in your phone, but leave the phone off.
Step 7.
Download the updated Root.zip from eugene373's guide: Root the Slide & Other HTC Devices*6/15/2010* How-To Updated 6/29/2010
Now let's get started...
Step 0.
Unzip Root.zip
Step 1.
Place the contents ("update.zip", "ota.zip", and "loop") into the Android SDK tools folder.
Step 2.
Open Command Prompt or Terminal and CD to the SDK tools directory.
Step 3.
Power on your device into the bootloader by holding the "Volume Down" key and simultaneously pressing Power.
Once you're in the bootloader, wait about 30 seconds until some diagnostic checking is done.
Press "Volume Down" to highlight Recovery, but do not push Power to execute just yet.
Step 4.
Now run your loop file from the prompt (either type "loop" in Windows or "./loop.sh" in Linux) (refer to ice3186's post for Mac instructions)
Note: The loop does nothing but show you the connection status of your phone. It's not technically required, but we'll use it in this guide.
Step 5.
Once the loop is running in your prompt, get ready to connect the phone to the computer with the USB cable, but don't connect one end quite yet. With Recovery still highlighted on your phone, you will need to push the Power button and then immediately plug in the other end of the USB cord.
Step 6.
After a few seconds, you should see your device listed in the loop.
Step 7.
Unplug the USB cable from the bottom of your phone and plug it back in. You probably don't need to do this, but let's be safe. Wait for your device to show up in the loop again. Hit CTRL-C to terminate the loop.
Step 8.
You should see a triangle/exclaimation over a phone graphic.
Hold the "Volume Up" key (note it's Volume UP this time) and simultaneously press Power.
After the menu comes up, use the volume and power buttons to select and run update.zip. (This will fail, but we already know that! Select it anyway.)
Step 9.
Paste the following command into your prompt and press Enter.
adb push ota.zip /sdcard/update.zip (*OSX users add a ./ in front of all terminal commands please)
Step 10.
This is very important!! Have this next command ready in your prompt before running update.zip again!!
This is the command. Paste it into your prompt, but DO NOT press Enter yet.
adb push update.zip /sdcard
Step 11.
Run update.zip and as soon as you see a faint progress bar appear behind the text at the bottom of the screen, push Enter to execute the command in your prompt.
Step 12.
If successful, you should see Clockwork Recovery and you now have Su and Superuser.apk installed! You can now reboot your phone into the OS to verify. If unsuccessful, repeat steps 11 and 12.
Step 13.
This step is optional, but it will save you the pain of going through all of these steps again in the future.
Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!)
I think some trouble shooting comments should be mentioned, so I'll just write a few things I noticed while rooting my device (for 7 frustration filled hours).
If you cannot see your device show up in 'adb devices' in recovery, boot into the OS normally and see if it shows up. If it does not, then it's a safe bet that you have one of two problems - you do not have all the drivers installed, or you do not have 'usb debugging' enabled. This can be enabled in 'settings->applications->development->usb debugging'. To avoid driver issues, it's highly recommended that you do this process in linux or osx.
If, on the other hand, your phone DOES show up in Android but not in recovery, or if it just blips on the screen for a second (when running the loop) as an offline device, then it might be the formatting of your sd card. Do NOT format your sd card from your phone or within Android. The ONLY time I managed to get the phone to show up in recovery without disappearing immediately was by removing the sd card, formatting it in windows or osx with an external card reader, copying the files over (new rom or rooting files), and then replacing it in the phone while the phone is off. After putting the card back in your phone, try the procedure again - go to the bootloader->hboot->recovery (while the cable is unplugged), then press the power button and immediately after plug the cable in (usually works when you plug the cable in about .2-.5 seconds later). If it does not show up at all, reboot the phone and try again, but do NOT let it boot back to Android. You can get back in to the bootloader by waiting until the 'HTC quietly brilliant' screen shows up and typing 'adb reboot bootloader' with the usb cable attached.
It took me a really long time to figure that out. I don't think the type of sd card matters so much as the formatting of it. I actually used the 2gb card that came with the phone, and it worked almost every single time after I reformatted the card.
Also, if you manage to get it working and root the phone, do yourself a huge favor and install the custom Unrevoked recovery image mentioned in the original rooting thread, so you never have to deal with this nonsense ever again.
Also also, if you get to the step where you do 'adb push ota.zip /sdcard/update.zip' and you get an error:0, installation aborted message, you did something wrong. The problem is that you aren't actually supposed to flash ota.zip. What you're supposed to do is push ota.zip to your phone as update.zip, and leave it there. Don't touch anything else. What you will do after that is type 'adb push update.zip /sdcard/update.zip' in the command prompt (WITHOUT hitting enter yet, just get ready to). You will then select 'sdcard:update.zip' and press power and IMMEDIATELY AFTER pressing power, you will press enter on the command prompt to execute your adb push command. What this does is causes recovery to read the ota.zip file you uploaded and recognize it as a legit update, but you replace it with update.zip before it actually gets extracted (if your timing is good). So recovery reads the signature of ota.zip, but actually extracts the stuff in update.zip and runs that instead.
Hope that helps with some common problems I observed. Good luck, dudes.
okay so I think I the only one using a Mac in this rooting process. A few things I have learned and may already be known but I thought I would clarify.
1.) to get a loop to run on the mac i had to re-write the file loop.bat
this is the code that works for me and how to do it.
a.) rename the file to end in .sh not .bat the way it came
b.) open the file with TextEdit
c.) delete all of the text in it and write this in there
Code:
while [ "0" ]
do
{
./adb devices
}
done
d.) save the file back in the sdk/tools folder
e.) in terminal the command once you cd to the folder is ./loop.sh
2.) i have yet to be successful in the attempt to root so anyone knowing anything to help would be appreciated! But i am still cracking i think i am going to wear out the plug before i am done though.
it should be pointed out that the loop does nothing except tell you if you have a connection or not. When you plug in the usb port, it will respond after a few seconds, or it won't. Try again.
gtg465x said:
Credit goes to eugene373 and attn1. These are mostly their instructions, but I did change, clarify, and add a few steps. If you can't get any of the other methods working, try this one.
Prerequisites...
Step 0.
Download and install HTC Sync: http://www.htc.com/us/support/aria-att/downloads/
Step 1.
Download and unzip the Android SDK: http://developer.android.com/sdk/index.html
Step 2.
Go into the folder where you unzipped the Android SDK and open "SDK Setup.exe"
When the "Choose Packages to Install" window pops up, make sure the package "Usb Driver package, revision x" is checked. You can uncheck everything else. Click Install. After it downloads and installs, close "Android SDK and AVD Manager".
Step 3.
With your device unplugged from your computer, go to Settings > Application > Development on your device and turn on USB Debugging.
Step 4.
Now plug your device in to your computer. This is just to make sure the USB drivers are installed.
Once they are installed, unplug your device and turn it off.
Step 5.
Download Root.zip from eugene373's guide: http://forum.xda-developers.com/showpost.php?p=6820344&postcount=1
Now let's get into it...
Step 0.
Unzip Root.zip
Step 1.
Place the contents ("update.zip", "ota.zip", and "loop") into the Android SDK tools folder.
Step 2.
Open Command Prompt or Terminal and CD to the SDK tools directory.
Step 3.
Power on your device into the bootloader by holding down the "Volume Down" key and simultaneously pressing Power.
Once you're in the bootloader, wait about 30 seconds, until some diagnostic checking is done.
Press "Volume Down" to highlight Recovery, but do not push Power to execute just yet.
Step 4.
Now run your loop file from the prompt (either type "loop" in Windows or "./loop.sh" in a *nix like) ( ./ Is used For OSX )
Step 5.
Once the loop is running in your prompt, get ready to connect the phone to the computer with the USB cable, but don't connect one end quite yet. With Recovery still highlighted on your phone, you will need to push the Power button and then immediately plug in the other end of the USB cord.
Step 6.
After a few seconds, you should see your device listed in the loop.
Step 7.
Unplug your USB cable from the bottom of your phone and plug it back in. You probably don't need to do this, but let's be safe. Wait for your device to show up in the loop again. Hit CTRL-C to terminate the loop.
Step 8.
You should see a triangle/exclaimation over a phone graphic.
Hold down the "Volume Up" key (note it's Volume UP this time) and simultaneously press Power.
After the menu comes up, use the volume and power buttons to select and run update.zip. (This will fail, but we already know that! Select it anyway.)
Step 9.
Paste the following command into your prompt and press Enter.
adb push ota.zip /sdcard/update.zip (*OSX users add a ./ in front of all terminal commands please.)
Step 11.
This is very important!! Have this next command ready in your prompt before running update.zip again!!
This is the command. Paste it into your prompt, but DO NOT press Enter yet.
adb push update.zip /sdcard
step 12.
Run update.zip and as soon as you see a faint progress bar appear behind the text at the bottom of the screen, push Enter to execute the command in your prompt.
Step 13.
If successful, you should see Clockwork Recovery and you now have Su & Superuser.apk installed! You can now reboot your phone into the OS to verify.
If unsuccessful, repeat steps 11 & 12.
Click to expand...
Click to collapse
This isn't complete - this just gets you to clockwork and you haven't installed anything yet. You need to add steps to add root acces or flash a rom that is rooted. Also, make sure to reference the unrevoked tool to install Clockwork after root so this whole ordeal can be avoided next time.
Yes! The secret was formatting the sd card outside of the phone. I am now rooted and liberated! Thanks for plugging along with all the advice guys!
modest_mandroid said:
I think some trouble shooting comments should be mentioned, so I'll just write a few things I noticed while rooting my device (for 7 frustration filled hours).
If you cannot see your device show up in 'adb devices' in recovery, boot into the OS normally and see if it shows up. If it does not, then it's a safe bet that you have one of two problems - you do not have all the drivers installed, or you do not have 'usb debugging' enabled. This can be enabled in 'settings->applications->development->usb debugging'. To avoid driver issues, it's highly recommended that you do this process in linux or osx.
If, on the other hand, your phone DOES show up in Android but not in recovery, or if it just blips on the screen for a second (when running the loop) as an offline device, then it might be the formatting of your sd card. Do NOT format your sd card from your phone or within Android. The ONLY time I managed to get the phone to show up in recovery without disappearing immediately was by removing the sd card, formatting it in windows or osx with an external card reader, copying the files over (new rom or rooting files), and then replacing it in the phone while the phone is off. After putting the card back in your phone, try the procedure again - go to the bootloader->hboot->recovery (while the cable is unplugged), then press the power button and immediately after plug the cable in (usually works when you plug the cable in about .2-.5 seconds later). If it does not show up at all, reboot the phone and try again, but do NOT let it boot back to Android. You can get back in to the bootloader by waiting until the 'HTC quietly brilliant' screen shows up and typing 'adb reboot bootloader' with the usb cable attached.
It took me a really long time to figure that out. I don't think the type of sd card matters so much as the formatting of it. I actually used the 2gb card that came with the phone, and it worked almost every single time after I reformatted the card.
Also, if you manage to get it working and root the phone, do yourself a huge favor and install the custom Unrevoked recovery image mentioned in the original rooting thread, so you never have to deal with this nonsense ever again.
Also also, if you get to the step where you do 'adb push ota.zip /sdcard/update.zip' and you get an error:0, installation aborted message, you did something wrong. The problem is that you aren't actually supposed to flash ota.zip. What you're supposed to do is push ota.zip to your phone as update.zip, and leave it there. Don't touch anything else. What you will do after that is type 'adb push update.zip /sdcard/update.zip' in the command prompt (WITHOUT hitting enter yet, just get ready to). You will then select 'sdcard:update.zip' and press power and IMMEDIATELY AFTER pressing power, you will press enter on the command prompt to execute your adb push command. What this does is causes recovery to read the ota.zip file you uploaded and recognize it as a legit update, but you replace it with update.zip before it actually gets extracted (if your timing is good). So recovery reads the signature of ota.zip, but actually extracts the stuff in update.zip and runs that instead.
Hope that helps with some common problems I observed. Good luck, dudes.
Click to expand...
Click to collapse
Really good tips. I hope you don't mind - I am going to link to this to my original thread.
Troubleshooting Tip on Prerequisite Step 2: If you're working behind a firewall, router, or proxy server, you're going to have to configure SDK Setup to use an open port on that device, in order to download updates.
I won't go through the exact steps here, but if SDK setup is hanging, this is the most likely culprit.
Regards,
Corporate Dog
Corporate Dog said:
Troubleshooting Tip on Prerequisite Step 2: If you're working behind a firewall, router, or proxy server, you're going to have to configure SDK Setup to use an open port on that device, in order to download updates.
I won't go through the exact steps here, but if SDK setup is hanging, this is the most likely culprit.
Regards,
Corporate Dog
Click to expand...
Click to collapse
get a copy of linux livecd and then you don't have to actually set up the SDK or worry about any drivers.
attn1 said:
This isn't complete - this just gets you to clockwork and you having installed anything yet. You need to add steps to root or flash a rom that is rooted. Also, make sure to reference the unrevoked tool to install Clockwork after root so this whole ordeal can be avoided next time.
Click to expand...
Click to collapse
If you made it to clockwork using this method then you're rooted. Check eugene's updated instructions. Look at the 6/29/2010 update on his original post... http://forum.xda-developers.com/showpost.php?p=6820344&postcount=1
I will add a reference to the unrevoked tool.
modest_mandroid said:
If, on the other hand, your phone DOES show up in Android but not in recovery, or if it just blips on the screen for a second (when running the loop) as an offline device, then it might be the formatting of your sd card. Do NOT format your sd card from your phone or within Android. The ONLY time I managed to get the phone to show up in recovery without disappearing immediately was by removing the sd card, formatting it in windows or osx with an external card reader, copying the files over (new rom or rooting files), and then replacing it in the phone while the phone is off. After putting the card back in your phone, try the procedure again - go to the bootloader->hboot->recovery (while the cable is unplugged), then press the power button and immediately after plug the cable in (usually works when you plug the cable in about .2-.5 seconds later). If it does not show up at all, reboot the phone and try again, but do NOT let it boot back to Android. You can get back in to the bootloader by waiting until the 'HTC quietly brilliant' screen shows up and typing 'adb reboot bootloader' with the usb cable attached.
It took me a really long time to figure that out. I don't think the type of sd card matters so much as the formatting of it. I actually used the 2gb card that came with the phone, and it worked almost every single time after I reformatted the card.
Click to expand...
Click to collapse
Excellent troubleshooting tips. I added a note about formatting your SD card to the prerequisites.
ice3186 said:
okay so I think I the only one using a Mac in this rooting process. A few things I have learned and may already be known but I thought I would clarify.
1.) to get a loop to run on the mac i had to re-write the file loop.bat
this is the code that works for me and how to do it.
a.) rename the file to end in .sh not .bat the way it came
b.) open the file with TextEdit
c.) delete all of the text in it and write this in there
Code:
while [ "0" ]
do
{
./adb devices
}
done
d.) save the file back in the sdk/tools folder
e.) in terminal the command once you cd to the folder is ./loop.sh
2.) i have yet to be successful in the attempt to root so anyone knowing anything to help would be appreciated! But i am still cracking i think i am going to wear out the plug before i am done though.
Click to expand...
Click to collapse
Thanks. Added a reference to your post.
attn1 said:
it should be pointed out that the loop does nothing except tell you if you have a connection or not. When you plug in the usb port, it will respond after a few seconds, or it won't. Try again.
Click to expand...
Click to collapse
Noted in the original post.
Corporate Dog said:
Troubleshooting Tip on Prerequisite Step 2: If you're working behind a firewall, router, or proxy server, you're going to have to configure SDK Setup to use an open port on that device, in order to download updates.
I won't go through the exact steps here, but if SDK setup is hanging, this is the most likely culprit.
Regards,
Corporate Dog
Click to expand...
Click to collapse
Thanks. Added the workaround.
attn1 said:
get a copy of linux livecd and then you don't have to actually set up the SDK or worry about any drivers.
Click to expand...
Click to collapse
Thanks. Added a note to the top of the prerequisites.
gtg465x said:
Step 12.
If successful, you should see Clockwork Recovery and you now have Su and Superuser.apk installed! You can now reboot your phone into the OS to verify. If unsuccessful, repeat steps 11 and 12.
Step 13.
This step is optional, but it will save you the pain of going through all of these steps again in the future.
Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!)
Click to expand...
Click to collapse
In no way, shape or form are you done after set 12.
You need to do more than just get into Clockwork. That alone doesn't root the phone.
gtg465x said:
If you made it to clockwork using this method then you're rooted. Check eugene's updated instructions. Look at the 6/29/2010 update on his original post... http://forum.xda-developers.com/showpost.php?p=6820344&postcount=1
I will add a reference to the unrevoked tool.
Click to expand...
Click to collapse
My mistake. He not only updated his instructions, he updated his update.zip. That should do it.
Good job!
I was just wondering If I have device issues after it is rooted, is it possible to remove the root and flash everything back to factory defaults for warranty purposes like the windows phones or is it once the warranty is gone it is gone?
steezee said:
I was just wondering If I have device issues after it is rooted, is it possible to remove the root and flash everything back to factory defaults for warranty purposes like the windows phones or is it once the warranty is gone it is gone?
Click to expand...
Click to collapse
Dunno if you can reflash the stock recovery again if you replaced it with clockwork, but you can definitely flash the stock ATT rom again. You can download it from HTC's site: http://member.america.htc.com/download/Web_materials/Manual/HTC_Aria_ATT/HTCAriaOriginalShipROM.exe
Banging my head on the wall. Got it to detect device once on loop. Never again after that. Phone shows up in device manager. Formatted 8gb and 2 gb cards several times.
urge growing. ... want to . . break.. . . .. . .random objects. . .
attn1 said:
My mistake. He not only updated his instructions, he updated his update.zip. That should do it.
Good job!
Click to expand...
Click to collapse
Sorry, I should have mentioned that he updated his update.zip.
You guys are right , there are missing step in the tutorial to fully root Aria.
after i get in to the clockwork from the step above. i have to install the custom rom that can be found in the forum.
when i try to install "Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!) " . the process goes throught but the recovery is still the same HTC blue color recovery screen.
so before you insert your sd card into the phone after you format the sd card. remember to copy the rooted rom into the sd card so when you successfully get into the clockwork. you want to install the rom then your aria is rooted with superuser icon on the application.
after then you do the "Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!) step .
There are no steps missing from the first post. I rooted my Aria using that method. Just make sure you have the latest Root.zip from eugene's thread. He updated it the other day and if you try to use the older version of Root.zip with this method it will not work.
What you are doing is installing a custom rom, which is fine, but it's not required to root the Aria.
i was trying to get the clockwork to install and it only work after i load the liberated_aria_b003_signed.zip
before i load liberated_aria_b003_signed.zip , it still give me the default HTC recovery screen.
after i load liberated_aria_b003_signed.zip and install "Unrevoked team: Recovery reflash tool (updated - Now for Aria/Liberty!) " . i get the clockwork screen as the recovery screen .
i still can't get the side loading to show after i follow the step from here
•COMMON:
•Enable USB debugging (settings > applications > development > USB Debugging)
•adb remount
•adb pull /data/data/com.android.providers.settings/databases/settings.db settings.db
Linux/OS X:
•echo "update secure set value = 1 where name = 'install_non_market_apps';"|sqlite3 settings.db
WINDOWS:
•echo update secure set value = 1 where name = 'install_non_market_apps';|sqlite3 settings.db
COMMON:
•adb push settings.db /data/data/com.android.providers.settings/databases/settings.db
•Reboot phone and sideloading works. (thanks to fluffyarmada)
.
I've read a couple dozen of the pages from http://forum.xda-developers.com/showthread.php?t=1905674&page=95 titled
Nabi2 root and Gapps install
Click to expand...
Click to collapse
.
Using Win7 x64. Nabi2 version: 1.9.37 recently updated.
Can't post to above thread because this is my first post (restricted to "General" forums).
In "Jmz Nabi Recovery Installer" window it is always stuck in the "If stuck here drivers are not installed" step.
Prior to installing "PdaNet for Android" from http://junefabrics.com/index.php,
I had 2 devices in Control Panel under "Other devices" with a yellow '!'. One of the looked like the Nabi device. The other is named "MTP".
After installing PdaNet, only MTP remains with the yellow exclamation point.
What should the Nabi look like in the Control Panel if its properly configured with a driver and where would it be?
And what is MTP?
Apparently I'm still having a driver/connection problem from adb.
USB Debugging is on in the Nabi.
Put the nabi in 'fastboot' mode
Open a CMD Prompt and browse to the 'files' folder within 'jmzrootpackage'
Then type:
adb.exe
fastboot devices
It should return a value (fastboot working and drivers are installed)
Let me know how it goes.
Put the nabi in 'fastboot' mode
Open a CMD Prompt and browse to the 'files' folder within 'jmzrootpackage'
Then type:
adb.exe
Click to expand...
Click to collapse
Part of this command is missing right? Without input parms it just outputs the "uses" message.
fastboot devices
Click to expand...
Click to collapse
Unfortunately this returned nothing for me.
I'm glad you responded. Other suggestions?
Here is how i done it using Windows 8 x64
I done 3 nabi2's this way but had a lot of trouble first so here is what worked for me:
Sadly, i don't have any nabi2 with me now to explain exactly how i done it
1) First boot the Nabi2 normally and turn off usb debugging.
2) When fully booted connect USB cable.
3) Check device manager and drivers should be installed.
4) Unplug USB cable and turn on USB Debugging and Unknown Sources.
5) Reconnect USB Cable.
6) Drivers should install.
7) Install PDA Net on Laptop/PC
8) Select Samsung device from option screen when installing.
9) Wait for install to complete and drivers to install
10) Shut down Nabi2
11) Boot Nabi in fastboot (Hold + and Power buttons)
12) Select fastboot protocol
13) Here i seen Windows 8 take about 60 seconds installing fastboot drivers
To make sure fastboot drivers are installed i went to this thread
Code:
http://forum.xda-developers.com/showthread.php?t=1590800
and download ADB (save it to C:\SDK\platform-tools) and read over the helpful instructions in the thread.
Open command Prompt
Type the following (shown in RED) in the CMD window the opened:
cd\
cd C:\SDK\platform-tools
adb.exe (a list of options should be listed)
fastboot devices (it should list a number after you enter this)
If number displayed then you are good to go.
Reboot Nabi2 and wait to complete
Go to the location you saved jmzrootpackage
Go to files folder inside jmzrootpackage
Double click install.bat
Follow on screen prompts ( I took option 1)
TWRP recovery installs
I had trouble installing GAPPS.zip with an error being displayed about unable to mount /data
I copied GAPPS.zip to a SD Card and inserted to Nabi2
i install zip from EXT-SD Card even though it gives a load of errors about not able to mount /data
Wipe Cache/Dalvik
Reboot Nabi2
Go to daddy/mommy mode and you should have Google Apps installed.
Any problems let me know.
I'm using Windows 7 x64.
Your instructions with selecting "Samsung" for PdaNet install appears
to have done something right. So maybe I'm a little closer.
It completed the PdaNet install successfully and when I reconnect the
Nabi I see a message popup on Windows saying PdaNet connected something.
(It was too quick.)
So maybe I'm not doing the "Fastboot" portion correctly.
On Nabi hold <Power> and <Vol+> down at same time to turn it on.
Resulting Menu:
Boot Normally
Fastboot Protocol
Recovery Kernel
Forced Recovery
Use <Vol-> to move the selected item.
Moved selected item down to "Fastboot Protocol".
Use <Vol+> to "enter" selected item.
New Menu:
Bootloader
Continue
Reboot-bootloader
Reboot
Poweroff
Selected "Continue", and entered(<Vol+>).
At this point the Nabi boots up.
On PC in adminstrator mode for command window and with ALL anti-virus
security turned off:
> adb.exe kill-server
> adb.exe start-server
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
> fastboot.exe devices
Nothing. (sigh)
After looking at Victoria Antonio's youtube of this process I'm convinced the driver install is still not correct.
Somehow it gets mucked up when I use PdaNet. Not sure how or why.
To make this picture clearer I posted some screen shots on my website: http <colon, 2 forward slashes>skippyvondrake.com
I hope someone can tell me how to unmuck what I've mucked.
skippyV said:
Selected "Continue", and entered(<Vol+>).)
Click to expand...
Click to collapse
Don't press Continue on the Nabi after selecting fastboot protocol
After selecting fastboot protocol leave it.
skippyV said:
> fastboot.exe devices
Click to expand...
Click to collapse
The command is:
fastboot devices
not
fastboot.exe devices
Thanks for telling me about when I'm in fastboot mode.
I DO get a device number when in fastboot mode and from 'fastboot devices'
But adb still cannot "see" the device. All commands using adb result in:
error: device not found
Regardless of what mode the Nabi is in.
SOLVED
I finally decided to try this with a different computer. Same OS and architecture.
But this computer didn't have various android development "kits" installed previously.
And it worked without a hitch.
The youtube by Victoria Antonio pointed out a few nuances I didn't know.
And you helped too, BBKGTTDi, so giving you "thank you" points.
Chow!
Glad you got it work SkippyV
I just need to figure out now, when i download a game to the Nabi2 from the playstore, how to get it so show in the kids mode
BBKGTTDi said:
Glad you got it work SkippyV
I just need to figure out now, when i download a game to the Nabi2 from the playstore, how to get it so show in the kids mode
Click to expand...
Click to collapse
When I get there - if I figure it out - I'll send you a private email sense that would be a different "thread'. There are other nuances I've noticed too...
show game in Nabi mode after rooting
@BBKGTTDi, I thought there would be a way to send private messages/emails on this forum - but I don't see it.
I ran into the same problem after rooting the Nabi. The "Add Apps" app doesn't work as its supposed to.
It worked prior to rooting.
It does list the newly installed apps, but selecting them for Nabi-Mode, rebooting, and they aren't there.
Only visible in Mommy/Daddy mode.
So if you figure it out please let me know!
The "Add Apps" app is working correctly now. Don't know what happened before.
I must be getting "Nabi-ed out".
Let me know if you're still having troubles.
skippyV said:
I'm using Windows 7 x64.
Your instructions with selecting "Samsung" for PdaNet install appears
to have done something right. So maybe I'm a little closer.
It completed the PdaNet install successfully and when I reconnect the
Nabi I see a message popup on Windows saying PdaNet connected something.
(It was too quick.)
So maybe I'm not doing the "Fastboot" portion correctly.
On Nabi hold <Power> and <Vol+> down at same time to turn it on.
Resulting Menu:
Boot Normally
Fastboot Protocol
Recovery Kernel
Forced Recovery
Use <Vol-> to move the selected item.
Moved selected item down to "Fastboot Protocol".
Use <Vol+> to "enter" selected item.
New Menu:
Bootloader
Continue
Reboot-bootloader
Reboot
Poweroff
Selected "Continue", and entered(<Vol+>).
At this point the Nabi boots up.
On PC in adminstrator mode for command window and with ALL anti-virus
security turned off:
> adb.exe kill-server
> adb.exe start-server
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
> fastboot.exe devices
Nothing. (sigh)
Click to expand...
Click to collapse
I ve got the same problem using windows xp, 7 or 8.1 after OTA update to jellybean.
Any ideas of what is going on?
arvati said:
I ve got the same problem using windows xp, 7 or 8.1 after OTA update to jellybean.
Any ideas of what is going on?
Click to expand...
Click to collapse
I did have those problems last year. Still think they were driver related.
I use mehtuus's package now. He has a useful install script.
http://forum.xda-developers.com/showthread.php?t=2172843
And when I want to use adb in "manual" mode I just launch a command prompt from his
'adb' directory (package is named 'mn2ri-v1.5.0-beta2.zip').
Try playing with his installer. And see if anything is displayed using:
Code:
adb devices
Thanks skippyV. I got it in fastboot last week with ubuntu and installed TWRP sucessfully.
hi all
i have got the eu pro 2 image files downloaded but i dont klnow how to create a bootable USB stick with these files so i can boot from it on my pro and reinstall from scratch.
Any guides anywhere ???
thanks
paul
Haven't tried it with a recovery image specifically, but I've done this plenty with an install image. There are tools, but I do it semi-manually:
1. Locate suitable flashdrive whose contents you can erase (back them up if needed) and plug it in.
2. Run CMD or Powershell (as Administrator).
3. Run "diskpart" (all commands are given in quotes and should be typed without quotes) and accept the UAC prompt if needed.
4. In diskpart, type "list disk" to see the list of disks, then type "sel dis [#]" (replace [#] with the disk number for the flashdrive).
5. Type "lis par" to see all partitions on the disk (typically only one) then "del par [#]" for each one to delete them.
6. Type "create par primary" to create a new partition spanning the whole flashdrive, then "lis par" to make sure it's selected (star next to it).
7. Type "format quick" to create a file system on the new partition, then "assign" to give it a drive letter.
8. Type "active" to make the new partition the one the OS will attempt to boot from, when booting off that drive.
9. Assuming everything succeeded, you can now exit diskpart ("exit").
10. Either unpack (using a program like 7-Zip) or mount (Win8 can do this automatically, or there's lots of software for older Windows versions) the disk image.
11. Copy the entire contents of the disk image (you can just use Explorer for this part if you mounted it) to the flashdrive.
Congrats, you have a bootable flashdrive containing a Windows installation (or recovery) image.
GoodDayToDie said:
Haven't tried it with a recovery image specifically, but I've done this plenty with an install image. There are tools, but I do it semi-manually:
1. Locate suitable flashdrive whose contents you can erase (back them up if needed) and plug it in.
2. Run CMD or Powershell (as Administrator).
3. Run "diskpart" (all commands are given in quotes and should be typed without quotes) and accept the UAC prompt if needed.
4. In diskpart, type "list disk" to see the list of disks, then type "sel dis [#]" (replace [#] with the disk number for the flashdrive).
5. Type "lis par" to see all partitions on the disk (typically only one) then "del par [#]" for each one to delete them.
6. Type "create par primary" to create a new partition spanning the whole flashdrive, then "lis par" to make sure it's selected (star next to it).
7. Type "format quick" to create a file system on the new partition, then "assign" to give it a drive letter.
8. Type "active" to make the new partition the one the OS will attempt to boot from, when booting off that drive.
9. Assuming everything succeeded, you can now exit diskpart ("exit").
10. Either unpack (using a program like 7-Zip) or mount (Win8 can do this automatically, or there's lots of software for older Windows versions) the disk image.
11. Copy the entire contents of the disk image (you can just use Explorer for this part if you mounted it) to the flashdrive.
Congrats, you have a bootable flashdrive containing a Windows installation (or recovery) image.
Click to expand...
Click to collapse
I've been building windows deployment images for years and I build my boot drives similarly to how you describe. The problem I've had is in getting a uefi bootable drive which I can use to take a drive image before I deploy a new one. In the past I've used tools like Make PE3 to make some useful boot drives but i'm not having nay luck with the newer pe4 or getting an older pe3 image to boot.
Secure boot is off, windows detects the drive and lsit it in the boot menu it just doesn't boot. Any suggestions?
Will_nonya said:
I've been building windows deployment images for years and I build my boot drives similarly to how you describe. The problem I've had is in getting a uefi bootable drive which I can use to take a drive image before I deploy a new one. In the past I've used tools like Make PE3 to make some useful boot drives but i'm not having nay luck with the newer pe4 or getting an older pe3 image to boot.
Secure boot is off, windows detects the drive and lsit it in the boot menu it just doesn't boot. Any suggestions?
Click to expand...
Click to collapse
Try pressing VOL - (I think its -, might be +) as it boots with the flash drive plugged in
lopezk38 said:
Try pressing VOL - (I think its -, might be +) as it boots with the flash drive plugged in
Click to expand...
Click to collapse
Thanks friend but that is not the issue. I can initiate the boot from USB but none of the boot images I've used in the past or that I've create new successfully boot. This problem is limited just to the surface pro.