========================================ACHTUNG===================
=================WARNING==========================================
=====================================================PELIGRO=======
AS WITH ANY UNSUPPORTED SYSTEM MODIFICATIONS, USING THIS MAY LEAD TO A BRICK
IF YOU DON'T KNOW WHAT YOU ARE DOING ( HAVEN'T BRICKED MY SYSTEM YET! ) PLEASE
BE AWARE THAT NO ONE ON THE INTERNET IS RESPONSIBLE FOR ANY DAMAGE TO YOUR
UNIT. ANY PROBLEMS WILL BE CONSIDERED ACTS OF WHATEVER GOD YOU BELIEVE IN.
======PELIGRO=======================================================
================================WARNING============================
===ACHTUNG=========================================================
For FYT SoM (5009/6011/6021/6022/6023) based JOYING / Intel SoFIA units ONLY!
Hello, here is a custom rom based on the SYU Stock Build [sofia3gr_car_64-userdebug 6.0.1 MMB29M eng.bsp.20180110.181524 release-keys]
Your Head Unit MUST ALREADY BE ROOTED! You must be able to obtain Super User access within Android!
Due to Bluetooth, WiFi, and as well as nvram patches in the ROM and bootloader, you must be running Joying 6.0 firmware dated 2017_12_15 or later to install this ROM.
Why this ROM? Simple answer: It's makes your Head Unit faster than running the stock ROM's, has updated Google Apps, and has the bloat removed! It's pre-rooted also!
INSTALLATION INSTRUCTIONS:
Step 1: Unzip the contents to the root of your USB flash drive on your computer, then plug the flash drive into the Joying unit via USB.
Step 2. Use the Android helper application "custom" to install. Download from link below, either on the Head Unit itself, OR on PC and transfer using ADB. Once installed, open the program, and grant superuser privileges when prompted, you'll be presented with screen as here:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Step 3: Click INSTALL CUSTOM. Wait for output to say recovery successfully installed!
If you wish to preserve your /data, AKA dirty-flash, click on "Do not wipe data" at this point to prevent your data partition from being wiped.
ALL EXISTING DATA ON UNIT WILL BE ERASED. THIS IS A CLEAN INSTALLATION!
Step 4: click REBOOT TO INSTALL GTX ROM - Your Joying unit will reboot, and installation will automatically proceed through TWRP.
(NOTE! The ROM automatically re-installs stock recovery during installation, so if something goes wrong, you can always restore to the original JOYING firmware.)
Recovery options:
RESTORE STOCK - Restores the original stock recovery
INSTALL CUSTOM - Installs superdave's custom recovery (needed to install this ROM)
VERIFY RECOVERY - tells you which recovery you have installed
Rom Utilities:
(all options on this menu work only if you have custom recovery installed)
"Do Not Wipe Data" Switch - enable this to prevent your /data partition from being wiped when installing the ROM. (Your results may vary. Works for me!)
REBOOT TO TWRP - Reboots to TWRP home screen allowing you to do things
INSTALL GTX ROM- installs joying_gtx stock rom from installation media
Exit - exit custom
Code:
====Includes====
xposed v87 x86
open gapps x86 Nano Feb 2018
ViPER4ANDROID FX
precompiled dalvik cache (first boot 2 minutes)
enabled eth0 at boot at 192.168.65.100 for debugging
ADB enabled
SeSuperuser built-in
Included [custom] app to manage superdavex's custom recovery for easy installation and maintenance
RightCamera (front cam app) modified APK
AOSP android boot animation
Interactive cpu governor:
go_highspeed_load set at 70% CPU load
titanium backup
nova launcher
GVC CallHandler 4 Joying
Amaze File Manager
Xposed modules:
boot manager
gravitybox
no overlay warning
immsersive mode forcer
app settings
fake wifi
GPSSpeedFix
======Removed======
[I]Debug Services:[/I]
usbactive
sqldebug
pekallfmrserver
watchdog
ap_logfs
apk_logfs
log-watch
crashlogd
adbusbmuxd
adbec
bootwatcher
shcmd
fmd
[I]Removed Apps:
[/I]
BasicDreams
BluetoothMidiService
Exchange2
Galaxy4
HoloSpiralWallpaper
LiveWallpapers
LiveWallpapersPicker
NoiseField
OpenWnn
PhaseBeam
PrintSpooler
GooglePinyinIME
RKUpdateService
CaptivePortalLogin
WAPPushManager
[I]removed from /system-priv-app
[/I]ManagedProvisioning
CallLogBackup
OemTelephonyApp
DeviceTest
StressTest
WallpaperCropper
GoogleFeedback
ProxyHandler
CellBroadcastReceiver
[I]Removed FYT APPS[/I] ( these slow the system down considerably, even when not in use )
SYU-1-C9-Calculator-V1.0
Sofia-1-C9-TV-V1.0
JY-1-C9-Video-V1.0
JY-1-C9-TimeWeather-V1.0
SYU-1-FileManager-V1.0
SYU-1-C9-Update-V1.0
Sofia-1-C9-ExDvr-V1.0
SYU-1-C5009-DVR-V1.0
Sofia-1-C9-Gallery-V1.0
JY-1-C9-MUSIC-V1.0
ZBox
note, this is a test release intended for developer users only. no support other than this post is offered. A final version will follow soon once initial testing has been completed.
Download Links
Installer ( unzip, this will help you install the ROM on a STOCK, un-rooted Head Unit ) :
xxxxx Mod Edit
custom V4_9
xxxxxxx Mod Edit
source code
Firmware Download:
V9 ALPHA 3
xxxxxx Mod Edit
Reserved for TWRP instructions.
Q / A:
Q: Do I need to worry about what MCU version I have before I use your rom?
A: Maybe, GTX ROM doesn't touch the MCU, which shouldn't be re-flashed with each install anyway as it usually doesn't change. Whatever MCU version you have, this ROM will work for you, as long as you have an FYT based SoM unit. If you encounter errors, you might need to change the "ro.build.fytmanufacturer" property in /system/app/fyt.prop to match whatever your unit ORIGINALLY came with.
Q: I have a RK3066/RK3188/PX3/PX5 based head unit. Will this ROM work for me?
A: NO! This ROM ONLY works on FYT based head units. This means all Joying Intel units, as well as some from other brands.
Q: I like Live Wallpapers. How do I enable them?
A: Use the built in terminal. type su and hit enter. You now have root. then type in:
Code:
cp -R /system/vendor/oem/LiveWall* /system/app
hit enter again, then reboot!
Q: I don't want to use this ROM anymore, what do i do?
A: Use the helper application, custom, open the program, and click RESTORE STOCK. This will restore the STOCK RECOVERY. Go on Joying's website [link], download the firmware of your choice, and follow their instructions.
Q: Can I use google voice to make hands free calls?
A: You sure can. Use the "Voice Search" app to dial a number using your voice, once at the Google App screen, click on the hamburger menu, and then select GV CallHandler 4 Joying. Make sure your unit is set to a DPI of at least 161dpi or greater, and then clear data on the google app. After you reboot, you should be able to make calls.
Q: How do I view my front camera?
A: If you are using the analog RCA video input, on the back of the unit, you can use the RIGHT CAMERA app to view. Note, than unlike the AUX program, this one will NOT mute the system audio.
Q: How can I fix my GPS speed to calculate 1/kmh or 1/mph steps instead of the default 4 steps?
A: Go to XPOSED INSTALLER, and enable the GPSSpeedFix module. Reboot, and the steps will be fixed.
Q: How can I enable different DPI settings for each application?
A: Go to XPOSED INSTALLER, and enable the App Settings module. Exit the installer, and open the App Settings to make your adjustments. Reboot, and your changes will be visible.
Q: This ROM is fast, but I want more speed, what do I do?
A: Add a fan to your unit, preferably a FAN + Heatsink. Then download an app like SetCPU to lock your CPU to MAX speed. Be careful.
Q: How do I re-assign the hard keys on my unit? Joying says that DVD and EJECT don't work! Is this a lie?
A: Yes! There is a way to re-assign keys, and the DVD and EJECT keys do actually work, the software that comes with the unit is not very good. Check @surfer63's XSofiaTweaker thread for more info on how this works.
Q: I want to send and receive my text messages on my Joying unit...is this possible?
A: Sure! Use third party app like Pulse, or Pushbullet. Works like a charm. I personally use Pulse, it's got the look and feel of a stock SMS app.
Q: Installing the Joying Factory Rom takes like an hour...multiple reboots, then it starts over, then it reboots, then it optimizes apps, then it starts over, again. jeez. How long does your ROM take to install?
A: Installation is less than 4 minutes. First boot is timed at one minute 53 seconds, and there are no crashes or reboots. It just works.
Q: Xposed says there is an update available! Is it safe to update Xposed?
A: NO! Do NOT update Xposed, it will make your unit non-functional! Just say NO!
Q: Am I able to "upgrade" from an earlier version of the ROM to a newer without loosing my data and apps?
A: Yes, read the first post on what option to select in custom. Many others and I have tested, and it works for almost all people, still there is a chance that it could not work.
Q: I need to download the stock Joying firmware so I may use your ROM! Where do I get the latest updates?
A: See here: https://drive.google.com/open?id=1nF5Pgn95_WWGk8S2byb8rR5ko0ss5F_S
Q: is there a video where I can see you install the ROM?
A:
Issues:
-Unable to send text message via google voice app using Pulse SMS, error is "Message couldn't be sent" // If anyone has a fix for this, please let us know
-Google Assistant doesn't work, launching activity manually results in "The Google Assistant doesn't work on this device" / You can fix this by changing the resolution to at least 720. use the command wm size to change the screen resolution or another tool that can change DPI
Release History:
custom helper:
V4_1: Fixed installation issue from micro sd cards.
V4_2: Check OS build fingerprint, will deny install unless you are on 20171215 or later.
V4_3: Updated text on installation screen for easier reading, Updated build detection logic
V4_4: Fixed bug in build detection logic
V4_5: Added no_data_wipe, translations included.
V4_6: fixed reboot to twrp not extracting recovery ota.
V4_7: lbug fixed
V4_8: script improvements
V4_9: prepare for re-write, added performance mode
ROM:
V4: Replaced opengapps with nano version
V5: Updated to 01-10 AOSP Base, Added bluetooth build property from @surfer63, more optimizations.
V6: Added Navi APK, more optimizations, CANBUS firmware included, various stability fixes, ability to "dirty flash", mcud included to prevent bootloops during app optimization, works with 800x600 units now, fixed overlay bug, faster first boot, added ViPER4ANDROID, added USB audio policy modifications.
V7: Fixed LED issues and AMP Options. Updated GAPPS base to 20180226, might need to optimize apps on first boot if you are dirty flashing. Added fyt.prop to /system/app fix various issues.
V8: Changes in the way the installer handles re-installation of stock recovery for disaster recovery situations in which the installation fails and custom recovery remains installed, changed installation logic to to compensate for faulty installation media, twrp bug fixes, fixed twrp restart loop, clear FYT flags on twrp start.
V9 alpha 1:
updated recovery busybox to 1.27
fixed SYU file manager not found in CM Settings
fixed right camera not displaying
updated MCUd build to co-exist with sofia server
eliminate audio pops during rebooting
updated gtx_installer
updated dalvik cache
fixed recovery_maintenance.sh in system and recovery envrionments
recovery maintenance.sh is now functional from recovery console
updated clean_rom.sh
permissions overlay fixed
fixed script logic in install-recovery on 6021 units
include terminal app APK
added nano x86 editor
added network_up.sh to ensure debug network access and SU daemon is always run
v9_alpha_2:
fixed drm video black screen issue
added rom version information to fyt_build.prop
sofiaserver runs audio through all channels during call
v9_alpha_3:
xposed module to prevent xposed from updating framework causing bootloops
added remount command to path
added display calibration app to launcher
include both 5_25 and 9_20 versions of McuUpdateAll.bin in /system/mcu/ (copy the corresponding version to /system/mcu)
keep JET and other apps as user to ease upgrade
V3 Rom link not working?
Just finished upload, Try now.
gtxaspec said:
Just finished upload, Try now.
Click to expand...
Click to collapse
Yes, works fine. Sorry for clicking the links too early
I can't do anything with it now, but a link is so easily clicked.
my joying head units have an internal amp, can I use this ROM?
usa911g said:
my joying head units have an internal amp, can I use this ROM?
Click to expand...
Click to collapse
Yes, no problem at all. If there are bugs we will share them all. Nothing specific for amp or no-amp models.
surfer63 said:
Yes, no problem at all. If there are bugs we will share them all. Nothing specific for amp or no-amp models.
Click to expand...
Click to collapse
because the EQ app for amp or non-amp models is different, so I concern that
usa911g said:
because the EQ app for amp or non-amp models is different, so I concern that
Click to expand...
Click to collapse
Actually it is one and the same app with different screen-layouts and functionality depending on the hardware.
The digital amp software is included.
Reserved.
As soon as I have time I will try this rom
the russian hackers at 4pda are using the following build.prop mods, anyone care to chime in? if they actually do something, I will include them.
Code:
ro.rk.install_non_market_apps=true
net.tcp.buffersize.default=4096,87380,256960,4096,16384,256960
net.tcp.buffersize.wifi=4096,87380,256960,4096,16384,256960
net.tcp.buffersize.umts=4096,87380,256960,4096,16384,256960
net.tcp.buffersize.gprs=4096,87380,256960,4096,16384,256960
net.tcp.buffersize.edge=4096,87380,256960,4096,16384,256960
persist.telephony.support.ipv4=1
persist.telephony.support.ipv6=1
persist.sys.purgeable_assets=1
ro.wifi.channels=14
media.stagefright.enable-http=true
media.stagefright.enable-player=true
media.stagefright.enable-meta=true
media.stagefright.enable-scan=false
I have no idea about the build props.
The custom V3 app did install the recovery image in one go. I do not know whether you improved something or the previous time was a glitch on my system when it gave that verification error.
I installed the V3 ROM. It works fine. It seems indeed faster than the original joying stock rom.
From what date are the GAPPS? The unit is trying to update all gapps. It is not really useful to have everything pre-odexed for a quick start (and it really is a quick start), when it immediately starts updating once you have finished the Google account setup.
(I myself also prefer the GAPPS micro package. I don't need and want google photos, youtube, google fit, etc. on my head unit.)
My JET apk is only partly working. At this moment I do not know why.
Replacing apps with mods (radio, BT, sofiaserver) works again now the apps are installed in /system/app
Copying the launcher.sh to /data does work. The launcher.sh works with the SofiaServer keymod as well as with the Xposed module sofiaservercustomkeymod (the one that uses the launcher.sh).
Installing a newer version ór installing one of the xposed modules currently doesn't work as it requires the package installer. The default package installer has been replaced by the googlepackageinstallers from the gapps. As such I can easily work around it by simply writing the apps to their folder in /system/apps. As soon as I upload my modules to the global xposed repository it is no problem anymore anyway as the Xposed installer can install it. I will still looking into why that one can install and my app not. I will also uninstall the google installer and replace it with the default package installer and see what happens.
And with regard to the customkeymod xposed module with settings screen: The settings screen itself works fine, but I still can't use the settings from my app. They stay empty.
Ok, if you think the microgapps is lighter I can cook that in.
gtxaspec said:
Ok, if you think the microgapps is lighter I can cook that in.
Click to expand...
Click to collapse
You might even consider nano or pico gapps and let users just install whatever else they need manually.
I'll do nano on v4 release which will be out tonight.
gtxaspec said:
I'll do nano on v4 release which will be out tonight.
Click to expand...
Click to collapse
Is Viper4Android working on this ROM?
Some time ago you said that you will investigate why is not working on the stock Joying but you never returned with an answer, can you please share your findings if you have any?
Thank you !
---------- Post added at 07:05 AM ---------- Previous post was at 07:03 AM ----------
surfer63 said:
(I myself also prefer the GAPPS micro package. I don't need and want google photos, youtube, google fit, etc. on my head unit.)
Click to expand...
Click to collapse
I second this .... I also prefer things kept extremely simple !
haven't tested viper. I will install it tonight and test it tomorrow morning on my drive.
Related
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
KatKiss ROM
MarshMallow 6.0.1 ReleaseAsus TF101
Please note that this version is made for and tested on the TF101 model.
This rom is an aosp based rom with my own additions on top of it.
The main motto of the rom being Kiss. Even though the Meerkat could give you a kiss, it stands for Keeps it Sweet and Simple too
Which means that just like the other K.A.T stuff, the rom's main goal is efficiency, speed/res ponsiveness,
while not adding bloated features that will slow things down
DOWNLOADS:
Latest Rom Version: KatKiss-6.0_034.zip | Mirror
[*] Gapps: opengapps pico
SuperSU: SuperSU BETA 2.52
Sound improvements & gps quick fix : K.A.T App
SL101 Compatibility Pack: KatKiss-6.0-sl101-compat-V5.zip (To flash after the rom for the Asus Slider SL101 only, DO NOT flash for the TF101 model)
Install Instructions:
These builds are designed to be installed with a recent recovery.
TWRP 2.8.1 is recommended: available here
Older versions of TWRP like 2.3.x won't work.
Backup everything !
Go to recovery
[*]The first time you install: Format /data (full wipe doesn't format)
(you can skip this step if you're already on the same main version of KatKiss, if ever you encounter a problem redo a full clean install and format /data and try again before reporting )
Then *EVERYTIME* flash (all together):
rom zip
SuperSU zip
[*]gapps zip
Wipe cache/dalvik
Reboot
Rom Main Features:
MultiWindow Support with 2, 3 or 4 panes setup
High speed and responsive oriented
High performance and overclocked KatKernel included
Dock keyboard Support with full special/function keys support
Global Keyboard Shortcuts / KeyOverride Macro association (See post #2 for more info)
HDMI Support
Battery Level Indicator & Dock Battery support + Mods (icon/Text/%)
CIFS, ext4, NTFS, ExFat support
RRO Theme Engine - Themes & more info
Native Android FSTRIM + Manual scripts for Database optimization and fstrim (see post #2)
Media Scanner Filters
Navbar with left, balanced (PixelC like) or middle aligned buttons.
All Wifi channels support
Integrated cpu & io performance settings panel
Custom Navbars buttons long press actions
Advanced power menu with reboot options.
User Immersive mode and actions with automode when docked setting
Advanced per application permission management (AppOps)
Ethernet-auto support
Misc utils Busybox, rsync...
Custom Quick Settings tiles
ChangeLog: http://public.timduru.org/Android/KatKiss/6.0/ChangeLog.html
Rom Source: https://github.com/timduru (branch katkiss-6.0)
Credits:
Original banner concept by i9apps, Bootanimation by mgeniusm, original drawing by BBF
Chainfire for SuperSU
WebPage
How to report
What to include in the report
Disclaimer: The usual
Use at your own risk, I won't be responsible for any damages caused to your Transformer or to yourself.
In most cases if something breaks, flashing a rom on top should fix it.
XDA:DevDB Information
KatKiss-MarshMallow, ROM for the Asus Eee Pad Transformer
Contributors
timduru
Source Code: https://github.com/timduru
ROM OS Version: 6.0.x Marshmallow
ROM Kernel: Linux 2.6.x
Based On: AOSP
Version Information
Status: Stable
Created 2016-02-19
Last Updated 2018-10-19
Tips
First Install
Make sure you do a format /data the first time you install the rom
(backup your internal storage first if you want to keep something)
The first boot after a rom flash can take a few minutes as ART is slower than dalvik to optimize the applications, but is faster after the 1st time.
(First boot takes ~4-5 minutes without gapps and 10+ minutes with gapps)
Also keep in mind that after a fresh install, it might take a bit of time to get up to full speed as media scanner & google are checking/scanning and restoring stuff.
Bluetooth
Bluetooth might require to be turned on twice before it scans and displays the available devices.
Wallpaper Modes
Different Wallpaper modes have been added in Settings => Display
** Normal (regular android mode)
** Disable System Wallpaper rendering (set as default)
** Disable Wallpaper service
2nd setting will prevent the wallpaper being rendered by the system making things faster and also freeing resources
That's the recommended setting you want to use if you are using a launcher that has internal wallpaper rendering
The Default included Launcher3 has internal rendering
For Nova: Go to its Settings => Desktop => Wallpaper Scrolling => Force, then set a wallpaper.
(You will see a black wallpaper if you're not using a launcher that can do internal rendering, If wallpaper is important and that you want to keep your current launcher, then switch back to the 1st setting)
Youtube
Depending on your network and tablet load, 720p videos might not play or take longer to buffer.
Switch to 480p in that case.
Some videos are also 720p60fps so you might need to switch back to 480p for these too.
You can also try an older youtube version and disable auto updates: youtube-v5.0.21
Google Play Movies
Our current Widevine DRM libs are not compatible in MM.
So you can't play a movie on the tablet with Google Play Movies as it requires that.
Starting a movie to play on chromecast should be fine as the drm will be the chromecast one in that case.
Now On Tap
Now On Tap requires the nano opengapps version, however our default /system partition is too small to accommodate them.
So if you want to install the nano or bigger opengapps version, you'll need to repartition the storage space first using Bigwheelie for extended partitions
Then activate Now on Tap from google now settings
Hardware keyboard layouts
More languages have been added in the default asusec keyboard
Set the keyboard layout through Settings => Language & Input => asusec => setup keyboard layouts
These also allow live switching without reboot with ctrl + space
Global Key Override/Shorcut Mecanism
Available in Settings => Dock => Add Key Override Actions
This will allow you not only to redefine function keys assignment, and other special keys actions,
but you'll also be able to assign global macro actions / app launch to any key + Meta key combination (shift Left or Right , ctrl..)
You can also add multiple actions to one key combination, simply click again on the "+" button for the same key combination.
For example if you want to assign to one key combination a list of action to run before going to bed for example, like: turn wifi off, Bluetooth off, mute sound, and turn screen off, you can do that
Note that starting multiple applications with one key is kinda a miss and hit for the moment due to some mecanism in android that seems to prevent applications to start too close to each others.
Storage (fstrim) and Database optimization:
Fstrim is native since 4.3 and will happen in the background if your tablet is idle / sleeping and that your battery is > 70%
There is also a script to run it manually in the rom: /etc/kat/optimizestorage
To optimize the Database: /etc/kat/optimizedb
To run both, open a terminal and run:
su
/etc/kat/optimize
MultiWindow
Multiwindow allows you to split the screen in 2, 3 or 4 panes
you can switch an app back and forth between multiwindow mode and regular mode while it's running
NavBar:
- To switch between full screen and split View you can use the
NavBar Buttons
The app that currently has the focus (or the latest used app if you're on the Desktop) will be used for the main pane (left and/or top depending on the mode and rotation)
And it will lay the remaining most recently used apps in the rest of the available 1-2-3 panes depending on the icon you click
- If you press a multiwindow icon again when in splitview mode, it'll bring the focused app back to fullscreen mode.
- To swap the 2 latest focused apps location / pane , long press on the
NavBar Button
- To change focus simply Tap on the app or use the
NavBar Button
That button can also be used in non multiwindow mode to switch quickly between the 2 most recent apps.
Global Actions:
Actions to switch the app between fullscreen / splitview 2-3-4 panes, swap, or switch between the 2 most recent apps have been added
so you can bind them to a key / key combination with the Global KeyOverride or long press on navbar button too.
Note: Most apps works ok in splitview mode, but some of them might crash or not refresh correctly sometime.
To manually position an app in one of the pane:
For the moment either reorder your apps before clicking on an auto mode icon,
or you can also activate the default Marshmallow Multiwindow mode to get extra icons to positions an app in a specific pane (activate it in developer options )
Then position the apps with the icons from the Recents screen. (default MM recents icons are for 2 or 4 panes)
Banners
First
Many thanks, Tim, for keeping the Tf101 alive!
I'm a little afraid to try, but I know I will
Officially my Transformer is one of the oldest devices I own and should really show its age.
But it just doesn't, it sets itself apart from the two other Tegra 2 devices (Notion Ink Adam and Acer Iconia) by being a thoroughly enjoyable device, which reacts very promptly to all input and still is mechanically perfect with great battery life.
Some hardware ingredients like DRAM and Flash seem to be made of better stuff (some benchmark show twice the memory bandwidth than Acer Iconia and NI Adam and the eMMC is lots better than Acer (Adam is notoriously terrible)), but mostly it must be the constant tweaking you (and Google?) have put in, because the performance only got better and better, even if the applications typically got fatter and fatter and 1GB of DRAM is no longer as plenty as it used to be with Android 2.2.
I surely can't say the same for my Nexus 7, which started being somewhat snappier than the Transformer and turned out pretty bad with LP even after turning off the journalling on ext4.
Marshmallow has disappointed me so far (only Nexus 10 migrated yet), mostly because my standard launcher SPB shell 3D no longer works on it and I just like it better than stock or any other.
And then I just don't see any significant improvements beyond Lollipop or rather CM 12 with all the privacy stuff already included. And I just love the fast task switching, which is part of the multiwindow support and which I have on a keyboard shortcut (hope it comes soon).
Somehow I also doubt that Nougat will be better in any sense except "better" Google integration.
But since I'm very much afraid of operating anything without the latest security patches, I'll just have to make the switch.
And I'm sure it will be as perfect as the current LP by the time Nougat comes out.
Thanks Timduru for making it possible
Link is ready, downloading :good:
Thank you. what I've failed to understand, do you need to install a separate root tool? Or is it included in the recommended recovery tool? It's still as i bought it in 2011... Thanks!
Thanks so much Tim gonna test this out
cwouter said:
Thank you. what I've failed to understand, do you need to install a separate root tool? Or is it included in the recommended recovery tool? It's still as i bought it in 2011... Thanks!
Click to expand...
Click to collapse
Just follow the procedure from the 1st post:
once you have the recovery installed:
the first time: format /data
then install all 3 zips at once: rom + supersu + gapps
then reboot.
Thank you Tim! Awesome as always. Gonna try ASAP.
One question...
What is the downside of not having omx codecs working?
xbs said:
Thank you Tim! Awesome as always. Gonna try ASAP.
One question...
What is the downside of not having omx codecs working?
Click to expand...
Click to collapse
No omx codecs means no gpu video acceleration, so it'll use cpu to decode instead.
Wait a bit before trying, 019b is coming fixing the reboots with some apps
New Version #019b
New rom version available: KatKiss-6.0_019b.zip
ChangeLog:
TF101:
- Fix reboots caused by some apps(ES file explorer, play music, youtube...)
- Fix ExFat support
TF101 KatKernel 122:
- net: Handle 'sk' being NULL in UID-based routing
- add native ExFat FS support
timduru said:
Just follow the procedure from the 1st post:
once you have the recovery installed:
the first time: format /data
then install all 3 zips at once: rom + supersu + gapps
then reboot.
Click to expand...
Click to collapse
It sounds so easy... First I don't really know how to install the recovery (hence, i have been spending 'only' app 7 hours on topic by now). I would assume from PWR+VOL- then Vol+ goes to recovery mode, but the device gets stuck with a android red expression mark. I then tried to install the Easyflasher 0.8.3 and managed to first delete the drivers and installed new universal ones. Rebooted and continue to follow the procedure and the Easyflasher on my Windows tells me i have successfully unbricked my Asus Stock. However, when i reboot, it looks all exactly the same, no data lost, no new installation. Then I could, or should?, flash a recovery. However, if i try to do it from the Easyflasher there is only the old TWRP 2.2.1. available and i fail to make use of the downloaded TWRP 2.8.1.1. CLick the Root, doesn't work either.
Then, the frustration goes up and the progress goes down... please advise and push me in the right direction! MUch appreciated!
cwouter said:
It sounds so easy... First I don't really know how to install the recovery (hence, i have been spending 'only' app 7 hours on topic by now). I would assume from PWR+VOL- then Vol+ goes to recovery mode, but the device gets stuck with a android red expression mark. I then tried to install the Easyflasher 0.8.3 and managed to first delete the drivers and installed new universal ones. Rebooted and continue to follow the procedure and the Easyflasher on my Windows tells me i have successfully unbricked my Asus Stock. However, when i reboot, it looks all exactly the same, no data lost, no new installation. Then I could, or should?, flash a recovery. However, if i try to do it from the Easyflasher there is only the old TWRP 2.2.1. available and i fail to make use of the downloaded TWRP 2.8.1.1. CLick the Root, doesn't work either.
Then, the frustration goes up and the progress goes down... please advise and push me in the right direction! MUch appreciated!
Click to expand...
Click to collapse
Installing the recovery is not really the focus of this thread, and it has been a really long time since I installed on mine
But what I would do, since you seem to have easyflasher and drivers working:
- Install TWRP 2.2.1 from easyflasher
- reboot to that TWRP 2.2.1
- Install the TWRP 2.8.1.1 flashable zip from TWRP 2.2.1
- reboot to the recovery and it should now be TWRP 2.8.1.1
Flashed all 3 zip ROM+su+pico but can't boot to Android.
After the Asus logo screen turns black and nothing happens.
Any ideas?
xbs said:
Flashed all 3 zip ROM+su+pico but can't boot to Android.
After the Asus logo screen turns black and nothing happens.
Any ideas?
Click to expand...
Click to collapse
sounds as if the new kernel didn't flash or something.
What recovery are you using ?
Even if the screen goes black you should get adb working after a few minutes, it's still doing things in the background normally.
Try to grab me a logcat + dmesg at that point.
EDIT: Found the problem, yeah kernel not flashing:
Flash it separatly for the moment: Tim_KatKernel_122_MM6.0.zip
that will be fixed in the next version.
xbs said:
Flashed all 3 zip ROM+su+pico but can't boot to Android.
After the Asus logo screen turns black and nothing happens.
Any ideas?
Click to expand...
Click to collapse
Unfortunately me too.
The only step from install note was the "Format" because of lack of time and data cable to copy everything from internal sd to my pc (only way for me is over the air with My Phone Explorer right now).
Tried 19 & 19b together with SuperSu 2.52 and gapps-arm-pico in one flash.
Backlight of screen is on, but then nothing happens over an hour.
---------- Post added at 13:46 ---------- Previous post was at 13:45 ----------
timduru said:
sounds as if the new kernel didn't flash or something.
What recovery are you using ?
Even if the screen goes black you should get adb working after a few minutes, it's still doing things in the background normally.
Try to grab me a logcat + dmesg at that point.
EDIT: Found the problem, yeah kernel not flashing:
Flash it separated for the moment: Tim_KatKernel_122_MM6.0.zip
that will be fixed in the next version.
Click to expand...
Click to collapse
Will do immediately!
---------- Post added at 14:00 ---------- Previous post was at 13:46 ----------
Just booted fine, into MM
New Version #019c
New rom version available: KatKiss-6.0_019c.zip
ChangeLog:
TF101:
- Fix Kernel not being installed
timduru said:
Installing the recovery is not really the focus of this thread, and it has been a really long time since I installed on mine
But what I would do, since you seem to have easyflasher and drivers working:
- Install TWRP 2.2.1 from easyflasher
- reboot to that TWRP 2.2.1
- Install the TWRP 2.8.1.1 flashable zip from TWRP 2.2.1
- reboot to the recovery and it should now be TWRP 2.8.1.1
Click to expand...
Click to collapse
Sounds like a plan, i tried and Easyflasher tells me it runs Wheelie,NV Flash then 'finished new reboot into recovery'. I do so, but android gets stuck in the recovery with an red expression mark, then it'll boot normal again.
Might it be that root access is blocking it? The Easyflasher root access tells me to first falsh recovery and put the superuser on sd.
I have installed both TWRP and SuperSu but both run into issues: the first tells me 'root is required' then closes, the second tells me 'no SU binary installed' then closes.
I then decided to go for a very crappy 1-click root access, see http://forum.xda-developers.com/showthread.php?t=1689193, with an even worse http://www.4shared.com/postDownload/ja5cFLAL/1-Click_Transformer_Root_11.html. This seems to have succeeded and i got root access (!) and the above described issues on TWRP and SuperSu were not gone.
Then in TWRP i couldn't select the zipfile TWRP 2.8.1, and after telling TWRP i had a TF101 i could select an older version like 2.3, which he was going to download. I had to confirm a path but decided to abort. I then tried to boot recovery but unfortunately, and not as i expected, it run into the same red expression mark. I then decided to run APX mode again and see if easyflasher could access root now. Also negative. Then run normal ABD mode and checked if i could do something with SuperSu, also negative.
So it seems my problem is that TWRP doesn't allow me to select the right zip file and as a result i can't run any recovery... any idea?
UPDATE: going back to apx flash the default TWRP2.2.1 then reboot to recovery succeeds in Easyflasher but the same red expression mark with Android. so also negative
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
V 3.0 - EMUI 8.0DONOT COPY MY WORK, Ask for Permissions
Code:
- I am not responsible for the damage of your cell phone if you do not correctly perform the steps
- loser warranty
- if you are not sure better not to touch and leave this page
COMPATIBLE WITH
with all versions, P20 lite, remember to know your original compilation if at any time you want to return to stock for example ANE-LX3C25 with this data you can return to stock.
This version is based on the official modification of EMUI, activating functions that are in the high-end versions, adding some modifications for their better performance.
REQUIREMENTS:
- EMUI 8.0.0
- Activate the OEM unlocking, which is in adjustment / developer options and leave it so forever to avoid conflict.
- unlock the bootloader.
- install the recovery that I will leave, automated from windows-linux
Guard the rom in an external memory.
Turn off the cell phone press the plus and power buttons until you have the TWRP window
Press WIPE
Press FORMAT DATA
Write the word "yes" without quotes and accept, just do the work
Press BACK to go back several times to the main window.
Press WIPE, then ADVANCE WIPE
Verify that the partition DATA this in the f2fs extension
Mark: Dalvik, cache, data, internal storage, system
IMPORTANT !: do not mark "micro sdcard".
Once you have marked, slide the "swipe to wipe" arrow to clear it.
Go back to the main sale, press INSTALL
Press SELECT STORAGE
Switch to Micro SDCard to find the rom.
Look for the MORFUZ rom and flash
At the end of the installation press "wipe davilk-cache", wait for it to finish.
Reboot system.
Congratulations now will start the rom MORFUZ
It seems that Huawei modified the modem partition in the September-October patch and the MORFUZ kernel does not work incoming and outgoing calls.
-IMPORTANTonly install this module from the root Magisk options if incoming and outgoing calls do not work.
https://mega.nz/#!F7oXzSRZ!8uuSCIx4UTbuWkTEYoFmTXTCwvIr6Reuc1vyq6OIhw0
Rom Siriuz
https://mega.nz/#!tYBjTQhC!yPbPXkazpQUy7bzLdm33rEapihBB8iVmSGlGxy1RweI
TWRP Mod by catuva21 - VERSION 2
unzip, the file is automatic
https://mega.nz/#!uD4FlCqL!ERBzP4ZWa2sR8f_wnn15F_cOFCdYVKgfYETjiehQkkQ
TELEGRAM GROUP
https://t.me/joinchat/ERAhfQ8kyF6_iH5nMun5dg
Contributors:
CATUVA21
Credits:
- Openkirin Recovery TWRP
- Alexxx1
- Chisetdel31260
ROM OS Version: ANE-L
ROM Kernel: Stock
ROM Firmware Required: EMUI 8.0.0
Version Information:
Status: Stable
Created on: 2018-06-30
Last Updated on: 2018-09-10
DESCRIPTION ROM SIRIUZDETAILS OF THE ROM
SIRIUZ 3.0
- Base firmware P20 lite (security patch for September).
- Custom kernel MorfuZ now works wifi and bluetooth.
- Huawei ID integrated and running.
- New bootanimation.
- New bootlogo.
- Percentage activated from start, for other models.
- Activated the font change in themes.
- New topics.
- 7 themes to change the font customization.
- Yorreciones de camara.
- Youtube advance updated.
- Adaway ad blocker.
- VolTe Activated.
- Magisk 17.1
SIRIUZ 2.6
- P20 lite base firmware (August security patch).
- MorfuzKernel 2.1 selinux Permissive.
- Turbo GPU.
- Added support init.d.
- Added busybox.
- Huawei ID back.
- Boot profile for the Darknnes-Blu_Active kernel within init.d improves performance.
- Change of the MTweaks auditor kernel application.
- Added Lent AR fun camera function.
- Magisk 16.7.
- Increase bitrate of photos and video, improve quality.
- Application of return mail.
- Youtube Mod Updated.
- New Gboard keyboard.
SIRIUZ 2.4
-Base firmware P20 lite(security patch jun).
-Activated Dual Speaker.
-Added DolbyAtmos in Music.
-New Boot logo.
-Added custom watermark for the P20 lite.
-Now without patches.
-Installation mode AROMA-INSTALLER.
-Music: stock or crack.
-Camera: stock, Mate10Pro or P20Pro.
-Root: Magisk or Supersu.
-Navbar, Use the fingerprint sensor as a navigation bar.
-Solid explorer, Kernel Auditor, Quick Reboot.
-MxPlayer.
-Sony Music.
-Eliminated the data space.
-Deodexed (improves optimization).
-Improvements in the quality of photos, video and sound..
-It eliminated unnecessary google applications.
-Added Call Recorder.
-Added Youtube Mod (function in the background).
-Activated multi-user X5.
-Keyboard change, google.
-Reduction of size of icons.
-Activated glove mode.
-Mtu 1500.
-Explored files improved.
-Added main screen design 5x5,5x6,6x5.
-Added more applications of social networks of Twin cloning.
. * facebook, faceboot lite
. * messenger, messenger lite
. * whatsapp, whatsapp mod
. * instagram
. * snapchat
. * telegram
. * twitter
. * mega
. * creativefrends
. * microsoft office
r2
when i go to security options settings app crashes
cant setup fingerprint id
oh now it works after playing with the instalation settings
I got an error during installation and start bootlooping, latter with more time I'll try again.
Thanks to share your work with us.
Error finishing the installation:
set_perm: some changes failed
Other problems:
-Does not detect micro sd
-You can not configure a screen lock method (settings close when you try to enter that section)
-Developer options can not be activated (the settings are closed when you press compile)
Those problems are what happened to me, I followed the installation instructions exactly as it says in the post
same problem with me
brandox0 said:
Error finishing the installation:
set_perm: some changes failed
Other problems:
-Does not detect micro sd
-You can not configure a screen lock method (settings close when you try to enter that section)
-Developer options can not be activated (the settings are closed when you press compile)
Those problems are what happened to me, I followed the installation instructions exactly as it says in the post
Click to expand...
Click to collapse
The rom is working or not?
thanks for the rom!
followed the install instructions except i didn't install the TWRP321_OREO_P20LITE.rar because i previously installed it following these instructions.
chose to install the custom kernel and SuperSU. not sure right now what else. i will write it down when i try the next build.
i encountered the following issues:
-error finishing the installation: set_perm: some changes failed during flashing (could this be because i didn't install your modded TWRP?)
-unable to set the lockscreen options
-unable to set up fingerprintid
-settings crashes when attempting to enable dev options
-sd card isn't detected within the fw
once i saw the sdcard isn't detected, i tried to recover from my latest backup but TWRP wasn't able because /system was only mounted as read-only (could this be as well because i didn't install your modded TWRP?).
ended up having to reflash stock from erecovery, rerooting and reinstalling TWRP in order to restore from my last backup (maybe i did something wrong?).
after reading the features list, i personally would use it as my main rom. i'd love to see it with viper4android included and with an all dark theme though but that's just me.
thanks for your work! looking forward to more!
luigi997 said:
The rom is working or not?
Click to expand...
Click to collapse
Well, if you eliminate the fact that the fingerprint reader or any other screen lock method does not work, you can not use the micro sd and the developer options are not available. So yes, the rom works.
You can try to urge it, maybe you're lucky and do not have mistakes.
brandox0 said:
Well, if you eliminate the fact that the fingerprint reader or any other screen lock method does not work, you can not use the micro sd and the developer options are not available. So yes, the rom works.
You can try to urge it, maybe you're lucky and do not have mistakes.
Click to expand...
Click to collapse
If i try to uninstall an app, the system reboot.
I've installed the modded kernel
Anyone with no issues? Can be used as a daily driver?
Please report back testers ^_^
[email protected] said:
Anyone with no issues? Can be used as a daily driver?
Please report back testers ^_^
Click to expand...
Click to collapse
Nope, so far I haven't seen anyone reporting positively. No fingerprintid and no security features makes the rom pretty much unusable as far as I've tested and seen on the thread. I'm awaiting to see how this develops..
Success
This rom is working prefectly.. i have keep on trying to re install the rom.I always follow the exact instruction, and i have found out. You will have a set_perm: some changes failed. IF you mark check the navbar, and status bar while in aroma installer.. I have able to use everything. Ill try to make a screenshot of it.
riorabel12 said:
This rom is working prefectly.. i have keep on trying to re install the rom.I always follow the exact instruction, and i have found out. You will have a set_perm: some changes failed. IF you mark check the navbar, and status bar while in aroma installer.. I have able to use everything. Ill try to make a screenshot of it.
Click to expand...
Click to collapse
Awesome! I'll try again!
Did you flash the recovery included in the post?
What do you mean with "If you mark check the navbar, and status bar while in aroma installer"?
Thanks for the feedback!
madalone said:
Awesome! I'll try again!
Did you flash the recovery included in the post?
What do you mean with "If you mark check the navbar, and status bar while in aroma installer"?
Thanks for the feedback!
Click to expand...
Click to collapse
YES. I HAVE FLASH THE RECOVERY. AND WHEN YOU FIRST DO THAT... AND YOU SHOULD PUT THE ROM INTO YOUR SD CARD..
YES, IF YOU MARK CHECK THE NAVBAR ANF STATSBAR. WHILE CHOOSING YOUR DESIRED APPS. YOU WILL SEE THAT IN THE VERY LAST PAGE OF THE AROMA INSTALLER. WHERE YOU HAVE THE OPTIONS. NAVBAR STATSBAR, SOLID EXPLORER, KERNEL AUDIATOR, AND the QUICK REBOOT. SO JUST MARK CHECK THE SOLID EXPLORER,KERNELAUDITOR,AND QUICK REBOOT..
SO TRY IT NOW. AND GIVE ME SOME FEEDBACK IF IT WORKS IN YOU. ALSO KINDLY TRY TO DO A SCREENSHOT. I DONT HAVE OTHER PHONE TO TAKE A SHOT ON IT. KUDOS THANKS
ok so i flashed the provided recovery and the rom following the instructions with the following options in aroma installer:
Kernel: Morfu2kernel
Root: SuperSU
Camera: P20 Pro
Music: Stock
Kernel Auditor
Quick Reboot
the installation went through except bootimage patcher failed at decompressing ramdisk (failure, aborting).
edit1: after a cache wipe, i rebooted the phone. the phone boots but no root.
tried to flash SuperSU through TWRP but failed.
wiped data/cache/dalvik/system & reflashed rom with Stock kernel & Magisk no bootimage patcher errors. after a cache wipe, rebooted & phone has root :victory:
brandox0 said:
I also want to try again, but I'm still not sure.
So far, how is the rom working? Is there a fault signal mentioned above?
Click to expand...
Click to collapse
so far i'm still getting all my apps installed. i'll letcha know how i get on with it.
edit2: as i am stubborn, i reflashed the rom with the custom kernel and Magisk. root is on and the phone seems to run smoothly.
madalone said:
ok so i flashed the provided recovery and the rom following the instructions with the following options in aroma installer:
Kernel: Morfu2kernel
Root: SuperSU
Camera: P20 Pro
Music: Stock
Kernel Auditor
Quick Reboot
the installation went through except bootimage patcher failed at decompressing ramdisk (failure, aborting). is that the kernel failing to install?
after a cache wipe, i rebooted the phone. the phone boots as expected.
Click to expand...
Click to collapse
I also want to try again, but I'm still not sure.
So far, how is the rom working? Is there a fault signal mentioned above?
madalone said:
ok so i flashed the provided recovery and the rom following the instructions with the following options in aroma installer:
Kernel: Morfu2kernel
Root: SuperSU
Camera: P20 Pro
Music: Stock
Kernel Auditor
Quick Reboot
the installation went through except bootimage patcher failed at decompressing ramdisk (failure, aborting).
edit1: after a cache wipe, i rebooted the phone. the phone boots but no root.
tried to flash SuperSU through TWRP but failed.
wiped data/cache/dalvik/system & reflashed rom with Stock kernel & Magisk no bootimage patcher errors. after a cache wipe, rebooted & phone has root :victory:
so far i'm still getting all my apps installed. i'll letcha know how i get on with it.
Click to expand...
Click to collapse
I worked perfectly, the only problem is that mobile became very slow.
rapza4 said:
I worked perfectly, the only problem is that mobile became very slow.
Click to expand...
Click to collapse
i had that plus overheating but after what i did in edit2 it was gone and the phone runs smoothly.
on another note: is it possible to make this rom have init.d support somehow? it'd be cool for stuff like Liveboot..
Custom firmware for FiiO M6, FiiO M7 and FiiO M9
Hi everone,
My hobby is modding and building ROMs so now I mod FiiO M6 and M7 firmware.
Why? Now you can install playstore and activate third party players like PowerAmp and Neutron or use streaming apps like Spotify or Tidal.
I hope you will enjoy my ROM
Installer Features
Installing MicroGapps and Playstore to download and activate third-party players (Requires my firmware to work)
Magisk Installer (Requires my firmware to work)
Mixplorer (File Manager)
Dark Theme Installing
Xpossed Framework Installer
Optimized Fiio Music App
Optional Tidal Installing
My Firmware Features
Improved sound (Editing system configurations, Alsa, Updated SoundLibs)
Optimized system resources
Magisk (Root)
Activated WiFi item in settings
Updated FiiO Music App
Fake Signatures support
Activated Init.d
Useful build.prop tweaks
Another Bootanimation
Changed font to Russia font (Ubuntu + Samsung One)
And many other improvements
How to install firmware: Youtube Instructions
M7 Firmware link: M7 Firmware
M6 Firmware link: M6 Firmware
M9 Firmware link: M9 Firmware
If you want to thank me financially:
Bitcoin: 1MeMen1FHZ5iut5KYmdJrQKBgk2e8hts7f
Ethereum: 0x4C90b19a78f19a6fbaA191C58cF0E87751588d3c
PayPal: http://paypal.me/antonixo
QIWI: https://my.qiwi.com/Konstantyn-YFrx47iPqT
Installation Instructions
1. Download my firmware and copy it to sd card
2. Go to recovery by off player and turning it on pressing next track and power if you use M7 or volume down and power for M6.
3. Wipe data using vol+ vol- and power buttons select "Wipe data/factory reset" paragraph
4. Press yes and reboot to recovery.
5. Go "Install update from sd card" and select archive with my firmware.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
6. Now Aroma installer starts. To controll in aroma installer use combination of pressing Power+Vol+ Power+Vol- and Power.
7. Go next page by using Power+Vol+ and select any paragraph you need.
8. Power+Vol+ to start installation.
9. After installation press power and reboot to the system (First loading will take about 3-7 minutes)
FAQA: Player becomes laggy!
B: I cannot fix bad processor of FiiO M7. Lags because you start use player another way. You update FiiO Music, install Playstore. Apps require more performance hardware. Try reinstall with old FiiO Music and without Gapps
A: How to go back to original firmware
B: You can easily go back flashing stock rom for FiiO M7 from here - M7 Firmware or for fiio M6 from here - M6 Firmware. Just flash it from recovery like my firmware
A: Why, when entering Magisk, there is a notification about an additional installation?
B: Since the magisk was installed "by hand", he did not unpack the files he needed to the Data section. To fix the problem without the module and install this module
A: Why is there only only my language in the keyboard?
B: Settings - Language & input - Virtual keyboard - Simple keyboard - Language
Uncheck the system languages and put them in the languages you need
A: Stuck on logo/bootloop!
B: Hold the power and pause button, after the screen turns off, press the button down, in recovery, select Wipe data.
Thanks for this, though I've been meaning around with it, magisk doesn't provide proper root, no root apps request and get granted root ever. Am I missing something?
Mentalmuso said:
Thanks for this, though I've been meaning around with it, magisk doesn't provide proper root, no root apps request and get granted root ever. Am I missing something?
Click to expand...
Click to collapse
Did you select magisk app in installer? You have M6 or M7?
tried this on a m9 and no luck im afraid, just stuck at the fiio logo on bootup, left for 30 mins, rebooted to recovery and wiped data again, left for an hour and no difference.
AntonIXO said:
Did you select magisk app in installer? You have M6 or M7?
Click to expand...
Click to collapse
M6, it seems userdata doesn't mount so the magisk data files don't install. You have the correct platform etc for mounting, but I'm not sure why it fails. Otherwise it all works great.
dubsflyt said:
tried this on a m9 and no luck im afraid, just stuck at the fiio logo on bootup, left for 30 mins, rebooted to recovery and wiped data again, left for an hour and no difference.
Click to expand...
Click to collapse
Flash stock firmware through recovery
AntonIXO said:
Flash stock firmware through recovery
Click to expand...
Click to collapse
Yeah sorry should have said, got it working again by flashing stock, but this rom didnt work unfortunately, happy to test again if you release another build or something
dubsflyt said:
Yeah sorry should have said, got it working again by flashing stock, but this rom didnt work unfortunately, happy to test again if you release another build or something
Click to expand...
Click to collapse
I've update rom. Try again.
cannot make it work even with new update:-(
unfortunately same result with the new update on the m9
any news?
installed on my M6 working great, the only thing I cant get working is magisk, I read above about the module zip but can't understand how to install it, apart from that everything is perfect, keep up the great work.
Paris333 said:
installed on my M6 working great, the only thing I cant get working is magisk, I read above about the module zip but can't understand how to install it, apart from that everything is perfect, keep up the great work.
Click to expand...
Click to collapse
Go to magisk, press cancel in window and install module from module menu
Please please update for m9...
Any news ?
m9 업데이트 해주세요 ... 제발 ..
Just tried today's version but it dows not install.
after installing statrs after 2 or 3 seconds it reboots
I seem to have the same issue as Mentalmuso and Paris333; Magisk isn't giving out root permissions on the M6. When I try to flash module.zip via the modules tab in the magisk manager app I get:
Code:
! Unsupported/Unknown image format
! Installation failed
The magisk debug log is only full of:
Code:
su: request from pid={XXXXX}
su: request from uid={XXXXX}
su: request rejected (XXXXX)
for all of the root applications I tried to test it with
but when I go to the "superuser" tab it aggravatingly says "No app has asked for superuser permission yet."
My magisk app is the default non-updated version installed via the proshi_m6_en aroma installer. I did do full factory reset via the debug menu and followed all instructions, so the installation is very clean. Everything that doesn't need root works perfectly fine, xposed even shows up as active. I've tried a few things, like updating to the new v22 magisk app via the v22 magisk manager, but I always just run into the same boot.img unsupported error as above. Maybe I've missed something, let me know if you need anything tested, as I do have a few M6 to play around with that I don't mind bricking.
On an unrelated note: your paypal says you are not accepting payments.
Admiral_Face said:
I seem to have the same issue as Mentalmuso and Paris333; Magisk isn't giving out root permissions on the M6. When I try to flash module.zip via the modules tab in the magisk manager app I get:
Code:
! Unsupported/Unknown image format
! Installation failed
The magisk debug log is only full of:
Code:
su: request from pid={XXXXX}
su: request from uid={XXXXX}
su: request rejected (XXXXX)
for all of the root applications I tried to test it with
but when I go to the "superuser" tab it aggravatingly says "No app has asked for superuser permission yet."
My magisk app is the default non-updated version installed via the proshi_m6_en aroma installer. I did do full factory reset via the debug menu and followed all instructions, so the installation is very clean. Everything that doesn't need root works perfectly fine, xposed even shows up as active. I've tried a few things, like updating to the new v22 magisk app via the v22 magisk manager, but I always just run into the same boot.img unsupported error as above. Maybe I've missed something, let me know if you need anything tested, as I do have a few M6 to play around with that I don't mind bricking.
On an unrelated note: your paypal says you are not accepting payments.
Click to expand...
Click to collapse
try installing magisk manager v7.5.1 , im using that one with success. Getting root access now. I think half of it is actually the super lag we are getting with having play store, i have put together a very stripped down version of the stock firmware, removed a load of useless apps that all take up precious ram. I am simply downloading my preferred streaming app (deezer) and a couple of other useful apps (terminal, root explorer, magisk manager) and storing them all on my ext sdcard to install after clean install. I seem to be having a pretty fluid experience now.
anyone can fix da M9 file? it does not install any file to the device...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today
Features:
https://github.com/crdroidandroid/crdroid_features/blob/11.0/README.mkdn
Flashing Instructions:
Flox is how LineageOS has chosen to name the repartitioned version of flo, which means that if you haven't repartitioned your Nexus 7 2013 you must repartition it before even trying to flash this. Please read LineageOS instructions here before trying anything.
Pre-installation:
Recovery (TWRP Lineage Recovery)
gapps arm (MindTheGapps OpenGapps)
Sources:
ROM: https://github.com/crdroidandroid
Kernel: https://github.com/mantinan/android_kernel_google_msm
Device: https://github.com/LineageOS/android_device_asus_flox
Download:
ROM
Known issues:
When scanning the face unlock the camera shows left side of video Ok but right side darkened, cameras seem to work ok on other apps.
Visit official website @ crDroid.net
crDroid Community Telegram
crDroid Updates Channel
Donate to help our team pay server costs
bestiatester said:
Code:
*** Disclaimer
I am not responsible for any damage you made to your device
You have been warned
crDroid is designed to increase performance and reliability over stock Android for your device also attempting to bringing many of the best features existent today
Features:
https://github.com/crdroidandroid/crdroid_features/blob/10.0/README.mkdn
Flashing Instructions:
Flox is how LineageOS has chosen to name the repartitioned version of flo, which means that if you haven't repartitioned your Nexus 7 2013 you must repartition it before even trying to flash this. Please read LineageOS instructions here before trying anything.
Pre-installation:
Recovery (TWRP Lineage Recovery)
ROM (Download from here)
gapps arm (MindTheGapps OpenGapps)
Sources:
ROM: https://github.com/crdroidandroid
Download:
ROM
Known issues:
Battery is shown as charging at 0 mA.
When scanning the face unlock the camera shows left side of video Ok but right side darkened, cameras seem to work ok on other apps.
Visit official website @ crDroid.net
crDroid <device> Telegram
crDroid Community Telegram
Donate to help our team pay server costs
Click to expand...
Click to collapse
OH MY GAWD I'M IN LOVE everything working great here. This rom is surprisingly smooth with MicroG installed. Long live the Nexus 7!
Mr.Conkel said:
OH MY GAWD I'M IN LOVE everything working great here. This rom is surprisingly smooth with MicroG installed. Long live the Nexus 7!
Click to expand...
Click to collapse
Can you share the steps you used to get microG to work? I am having a hard time getting them to work on LOS 18.1 and This ROM as well!
GeekyTanuj said:
Can you share the steps you used to get microG to work? I am having a hard time getting them to work on LOS 18.1 and This ROM as well!
Click to expand...
Click to collapse
Well the steps can be different on Los 18.1 because Signature spoofing is not built in to Los but it is on Crdroid which makes it was less of a pain because you don't need Xposed for things to work correctly.
So starting with Crdroid go about your normal setup and install Magisk per normal. Afterwards you're going to need to select a package from this link normally minimalAP or the Standard package should be just fine. These packages have everything you need to get MicroG working with the Google Play store the only difference between minimal is Aurora Services and the location backends which a tablet doesn't necessarily need but it depends on what you use it for.
After flashing this through recovery follow these steps..
Initial Setup:
- Complete the setup wizard actions as you prefer
- Open the app drawer and long-press on Play Store to choose the App Info button
- Go to Permissions, then Additional permissions and change Spoof package signature to Allow, go back to home screen afterward
- Run the microG Settings app — The rest of these instructions are taken almost directly from https://gitlab.com/Nanolx/NanoDroid/-/blob/master/doc/microGsetup.md
- Choose Self-Check at the top of the list, and start tapping on the second item, System grants signature spoofing permission which should prompt a permission request
- Everything should now be checked on the Self-Check screen, go back to main microG Settings screen
- Choose Google device registration and enable the Register device switch, then go back
- Choose Cloud Messaging and enable the Receive push notifications switch, then go back
- SafetyNet doesn't actually work or pass right now, but you can try enabling it in the same manner as above
- Choose Location modules and enable at least one "Network-based Geolocation module" and one "Address lookup module". I usually only turn on Deja Vu Location Service from the top list; it seems to work well enough for driving directions here, and of course choose Nominatim from the lower list because it's the only one there
- This is important: Reboot now before you add a Google account or do anything else to the Play Store app
- After rebooting, go back into microG Settings app and make sure that all of the Self-Check items are still checked, and then make sure that Google Device Registration, Cloud Messaging, and SafetyNet are still enabled — if they were not, enable them.
- Now get app info for Play Store, clear cache (yes, again), then launch the app
- Add your Google account, and verify that it will show your app library — Purchased apps won't show as paid-for yet, this will take approximately 24 hours until Google decides it likes your new Android ID
- Open Settings app, then Accounts then choose your Google account, then chose Personal info & privacy, and make sure Allow apps to find accounts is enabled
- That should be everything!
Then after a few hours (a day or so) you should have complete access to you paid apps and you're good to go. Let me know if you need anything else!
Mr.Conkel said:
Well the steps can be different on Los 18.1 because Signature spoofing is not built in to Los but it is on Crdroid which makes it was less of a pain because you don't need Xposed for things to work correctly.
So starting with Crdroid go about your normal setup and install Magisk per normal. Afterwards you're going to need to select a package from this link normally minimalAP or the Standard package should be just fine. These packages have everything you need to get MicroG working with the Google Play store the only difference between minimal is Aurora Services and the location backends which a tablet doesn't necessarily need but it depends on what you use it for.
After flashing this through recovery follow these steps..
Initial Setup:
- Complete the setup wizard actions as you prefer
- Open the app drawer and long-press on Play Store to choose the App Info button
- Go to Permissions, then Additional permissions and change Spoof package signature to Allow, go back to home screen afterward
- Run the microG Settings app — The rest of these instructions are taken almost directly from https://gitlab.com/Nanolx/NanoDroid/-/blob/master/doc/microGsetup.md
- Choose Self-Check at the top of the list, and start tapping on the second item, System grants signature spoofing permission which should prompt a permission request
- Everything should now be checked on the Self-Check screen, go back to main microG Settings screen
- Choose Google device registration and enable the Register device switch, then go back
- Choose Cloud Messaging and enable the Receive push notifications switch, then go back
- SafetyNet doesn't actually work or pass right now, but you can try enabling it in the same manner as above
- Choose Location modules and enable at least one "Network-based Geolocation module" and one "Address lookup module". I usually only turn on Deja Vu Location Service from the top list; it seems to work well enough for driving directions here, and of course choose Nominatim from the lower list because it's the only one there
- This is important: Reboot now before you add a Google account or do anything else to the Play Store app
- After rebooting, go back into microG Settings app and make sure that all of the Self-Check items are still checked, and then make sure that Google Device Registration, Cloud Messaging, and SafetyNet are still enabled — if they were not, enable them.
- Now get app info for Play Store, clear cache (yes, again), then launch the app
- Add your Google account, and verify that it will show your app library — Purchased apps won't show as paid-for yet, this will take approximately 24 hours until Google decides it likes your new Android ID
- Open Settings app, then Accounts then choose your Google account, then chose Personal info & privacy, and make sure Allow apps to find accounts is enabled
- That should be everything!
Then after a few hours (a day or so) you should have complete access to you paid apps and you're good to go. Let me know if you need anything else!
Click to expand...
Click to collapse
Thanks for this guide! Really helped me get things going smoothly! Love this ROM.
Hi,
I need dt2w but i can't activate it, does thé kernel support it?
Can you Hello me please?
Thanks you
jojo33680 said:
Hi,
I need dt2w but i can't activate it, does thé kernel support it?
Can you Hello me please?
Thanks you
Click to expand...
Click to collapse
you need to use the Exkernel to enable dt2w. Here's the latest one: Link.
I am running an old 7.0 Resurrection ROM on my N7.
TWRP is installed & bootloader unlocked so I suspect I would just need to repartition & install?
No clue why ADBgives me these errors in powershell.
fastboot : The term 'fastboot' is not recognized as the name of a cmdlet, function, script file, or operable program.
Check the spelling of the name, or if a path was included, verify that the path is correct and try again.
At line:1 char:1
+ fastboot
+ ~~~~~~~~
+ CategoryInfo : ObjectNotFound: (fastboot:String) [], CommandNotFoundException
+ FullyQualifiedErrorId : CommandNotFoundException
For those who have partition with a different method like me that is NOT flox so they can flash other ROMs, replace this in the ROM zip. All I did was remove assert get prop that checks to make sure your tablet is the right one for the ROM. It won't flash if you're not using flox repartition so I changed it to allow it to flash. I have 1.6gb of system space and am able to flash this ROM, opengapps pico, magisk and custom kernel with no issues running a non flox repartition.
updater-script
drive.google.com
Hi!
In the known issues I descrived:
When scanning the face unlock the camera shows left side of video Ok but right side darkened, cameras seem to work ok on other apps.
Can anybody please confirm that this is happening also for you?
And if you know why it is failing or even better, how to fix it... that would be great
Thanks in advance.
bestiatester said:
Hi!
In the known issues I descrived:
When scanning the face unlock the camera shows left side of video Ok but right side darkened, cameras seem to work ok on other apps.
Can anybody please confirm that this is happening also for you?
And if you know why it is failing or even better, how to fix it... that would be great
Thanks in advance.
Click to expand...
Click to collapse
I confirm I have the same problem
Hello all,
I follow the guides and the installation went smoothly, thanks for the really good job you've done.
I'm new in the crDroid world so sorry if the question seems stupid: As the power button of the Nexus 7 is not easy to access, how can I activate the double tap to wakeup ?
Some years ago the tablet was installed with aicp, and the DT2W was working. So I'm a little bit disappointed if it is not working now.
Thanks.
Davidtre07 said:
DT2W
Click to expand...
Click to collapse
This material will help you: 01 ... 02 ... 03 ... 04
lyushiK said:
This material will help you: 01 ... 02 ... 03 ... 04
Click to expand...
Click to collapse
With Anykernel installed works like a charm !
Thanks.
Davidtre07 said:
With Anykernel installed works like a charm !
Thanks.
Click to expand...
Click to collapse
If you have a patch or pointer to the code that makes it work... just let me know and I'll try to add it.
I'm testing a patch for the charge current to be shown ok, seems to work, if all the tests are ok I'll ship it in with the next release.
No I don't have any patch to propose, I just followed the links provided by @lyushiK.
As far I understood, to work you have to recompile a kernel with DT2W hability and you have to activate it with the right flag in the kernel.
From my side what I've done:
Installed Magisk (patched boot.img)
Installed this kernel: https://androidfilehost.com/?fid=7161016148664820402
And to finish added to magisk this module: https://github.com/ipdev99/mModule_dt2w
Reboot and it works !
In Magisk I see the module is looking in /sys/ for "doubletap*" or "dt2w*" or "wake_gesture".
If it found one of the files then activate it (echo 1 in the file)
But still, you have to have the right kernel !
Thanks very much, this Rom is so smooth and running great. The only thing I've noticed is that the icon size and text is very small when using the tablet in landscape mode but fine in portrait mode. Any changes I make to the icon size from the settings apply in portrait but when switched to landscape stay as really small, is there any setting I have missed to enlarge them?
Thank you for the great work!
Just for feedback: I can confirm the camera issue, too, though it doesn't bother me.
Another small thing I noticed: during the initial setup my device was called Pixel 6 Pro (first I thought, I chose the wrong image) but in the settings it says correctly "Nexus 7".
What is this?
Pixel Experience is an AOSP based ROM, with Google apps included and all Pixel goodies (launcher, wallpapers, icons, fonts, bootanimation)
Our mission is to offer the maximum possible stability and security, along with essential and useful features for the proper functioning of the device
Based on Android 12.0 (11 is available but 12 has no difference in terms of issues and is faster an the better ui and everything else of course)
Disclaimer:- This will void warranty.
You will need to unlock bootloader.
*All your data will be lost*
Read all the steps correctly
BUGS:- bluetooth ear/headphones do not work workaround- ( go into phh treble settings misc features and enable force-disable a2dp offload (thanks to @Lil_Boudy for figuring it out!)
If bluetooth crashes your system disable media recommendations under Sound & Vibration > Media > Show media recommendations
mtp not working (mtp does work in twrp and in some custom kernels the one linked here does not fix mtp as it is not changing too many things compared to other custom kernels which brick some phones)
sim 1 incoming and outgoing does not work (you can revieve calls and call but you wonth hear anything nor will your mic go trying to fix) (workaround is to put your sim into slot 2) (i have heard that other people dont have this issue so i guess try your luck)
DO NOT let the phone die of battery you will not be able to boot you can get back by holding volume down and power (workaround- in magisk install acca https://github.com/Magisk-Modules-Repo/acc and install this apk after installing https://github.com/MatteCarra/AccA then set profile to default (this will shut down the phone at 5% hence removing the risk of your phone not booting after hitting 0%
You tell me
Links
Source (Kernel Source)
https://github.com/topjohnwu/Magisk/files/7819803/app-debug.zip (magisk)
Rom download.
1.Need TWRP 3.4.0 or higher!
2. Unpack the "xz" archive and put the .img file onto the sd card or internal (if you dont have a sd card do step 3 then transfer the img file to your phone)
3. In TWRP head to factory reset format type yes and hit enter
4. Flash the img file (as system obviously)
5 install magisk (the one linked above only) (optional but you should as a lot of modules are listed here are very important (ie the acc module and the fast charging module)
5.5.Reboot and enjoy!
Zainullah Boot fix (if you cant boot)
install oneui boot into oneui change date to 3 months from now
check for updates
boot into download mode
flash twrp 3.6.0 and vbmeta
boot into twrp
do format data
flash multidisabler
flash rom
flash kernel as boot
do factory reset
reboot
if it boots you into fastboot shutdown flash twrp only and try another factory reset and reboot (In twrp)
Install Gcam go by greatness from here
https://www.celsoazevedo.com/files/android/google-camera/dev-greatness/f/dl9/
also enable extra cameras in phh treble settings - samsung settings for ultrawide
Increase performance without any battery impact or (by feravolt and gloeysik)
Step 1
- Uninstall ANY OTHER KERNEL MANAGER app including smartpack/Ktweaks to avoid conflict, since this app uses AI and machine learning to dynamically boost performance when needed
- Install FDE AI Magisk Module to make it a system app, thus it will work better and removes all kernel locks from OEMs (I'm looking at you, Samsung) https://github.com/feravolt/FDE.AI-docs/releases/download/12.4.1m/FDE.AI-as-system-app.MAGISK.zip
- Update FDE AI to the latest version by downloading the latest APK here, since the fde ai magisk module will only install fde ai 12.4.1, not the latest version: https://github.com/feravolt/FDE.AI-docs/releases
- Move to the bottom of the screen and select AI Chat, then type /advancedai (no space, no uppercase letters). This will going to make the AI more effective, without you having to do anything.
- Go to the settings tab and use the AUTO settings for FDE AI.
Optimized and adjusted Google Play services. Contribute to gloeyisk/universal-gms-doze development by creating an account on GitHub.
github.com
install cloudflaredns4magisk (install both ipv4 and ipv6 versions) (this will switch you to cloudflares faster and more secur dns
Cloudflare dns magisk download
install adaway (optional if you want ads or not) , allow superuser for it download this https://energized.pro/bluGo/formats/filter in adaway click he button in the middle click add click file and add the file then go back to the main menu and click the reload button now https://adaway.org/
(you get better battery and performance in adaway)
also enable extra cameras in phh treble settings - samsung settings for ultrawide
install universal safteynet fix zygsik (magisk)to get safteynet working
enable denylist for apps you want to hide root from (dont enable it for google play services as it is not needed)
ALL credit goes to phusson , ponces and rest of the devs
Blog
Pixel Experience
Donate
jhenrique09
phhusson
AndyYan
eremitein
ponces
.
.
Reserved
You set it for as a question xD. Also for what model is this made?
Thanks for your work.
LAST_krypton said:
You set it for as a question xD. Also for what model is this made?
Thanks for your work.
Click to expand...
Click to collapse
it works on all models
Zainullahk1234 said:
What is this?
Pixel Experience is an AOSP based ROM, with Google apps included and all Pixel goodies (launcher, wallpapers, icons, fonts, bootanimation)
Our mission is to offer the maximum possible stability and security, along with essential and useful features for the proper functioning of the device
Based on Android 12.0 (11 is available but 12 has no difference in terms of issues and is faster an the better ui and everything else of course)
Disclaimer:- This will void warranty.
You will need to unlock bootloader.
*All your data will be lost*
Read all the steps correctly
BUGS:- bluetooth ear/headphones do not work workaround- ( go into phh treble settings misc features and enable force-disable a2dp offload (thanks to @Lil_Boudy for figuring it out!)
If bluetooth crashes your system disable media recommendations under Sound & Vibration > Media > Show media recommendations
mtp not working (mtp does work in twrp and in some custom kernels the one linked here does not fix mtp as it is not changing too many things compared to other custom kernels which brick some phones)
sim 1 incoming and outgoing does not work (you can revieve calls and call but you wonth hear anything nor will your mic go trying to fix) (workaround is to put your sim into slot 2) (i have heard that other people dont have this issue so i guess try your luck)
DO NOT let the phone die of battery you will not be able to boot you can get back by holding volume down and power (workaround- in magisk install acca https://github.com/Magisk-Modules-Repo/acc and install this apk after installing https://github.com/MatteCarra/AccA then set profile to default (this will shut down the phone at 5% hence removing the risk of your phone not booting after hitting 0%
You tell me
Links
Source (Kernel Source)
https://github.com/topjohnwu/Magisk/files/7819803/app-debug.zip (magisk)
Rom download.
1.Need TWRP 3.4.0 or higher!
2. Unpack the "xz" archive and put the .img file onto the sd card or internal (if you dont have a sd card do step 3 then transfer the img file to your phone)
3. In TWRP head to factory reset format type yes and hit enter
4. Flash the img file (as system obviously)
5 install magisk (the one linked above only) (optional but you should as a lot of modules are listed here are very important (ie the acc module and the fast charging module)
5.5.Reboot and enjoy!
Zainullah Boot fix (if you cant boot)
install oneui boot into oneui change date to 3 months from now
check for updates
boot into download mode
flash twrp 3.6.0 and vbmeta
boot into twrp
do format data
flash multidisabler
flash rom
flash kernel as boot
do factory reset
reboot
if it boots you into fastboot shutdown flash twrp only and try another factory reset and reboot (In twrp)
Install Gcam go by greatness from here
https://www.celsoazevedo.com/files/android/google-camera/dev-greatness/f/dl9/
also enable extra cameras in phh treble settings - samsung settings for ultrawide
Increase performance without any battery impact or (by feravolt and gloeysik)
Step 1
- Uninstall ANY OTHER KERNEL MANAGER app including smartpack/Ktweaks to avoid conflict, since this app uses AI and machine learning to dynamically boost performance when needed
- Install FDE AI Magisk Module to make it a system app, thus it will work better and removes all kernel locks from OEMs (I'm looking at you, Samsung) https://github.com/feravolt/FDE.AI-docs/releases/download/12.4.1m/FDE.AI-as-system-app.MAGISK.zip
- Update FDE AI to the latest version by downloading the latest APK here, since the fde ai magisk module will only install fde ai 12.4.1, not the latest version: https://github.com/feravolt/FDE.AI-docs/releases
- Move to the bottom of the screen and select AI Chat, then type /advancedai (no space, no uppercase letters). This will going to make the AI more effective, without you having to do anything.
- Go to the settings tab and use the AUTO settings for FDE AI.
Optimized and adjusted Google Play services. Contribute to gloeyisk/universal-gms-doze development by creating an account on GitHub.
github.com
install cloudflaredns4magisk (install both ipv4 and ipv6 versions) (this will switch you to cloudflares faster and more secur dns
Cloudflare dns magisk download
install adaway (optional if you want ads or not) , allow superuser for it download this https://energized.pro/bluGo/formats/filter in adaway click he button in the middle click add click file and add the file then go back to the main menu and click the reload button now https://adaway.org/
(you get better battery and performance in adaway)
also enable extra cameras in phh treble settings - samsung settings for ultrawide
install universal safteynet fix zygsik (magisk)to get safteynet working
enable denylist for apps you want to hide root from (dont enable it for google play services as it is not needed)
ALL credit goes to phusson , ponces and rest of the devs
Blog
Pixel Experience
Donate
jhenrique09
phhusson
AndyYan
eremitein
ponces
Click to expand...
Click to collapse
Whre is the ROM?
leonardo07746 said:
Whre is the ROM?
Click to expand...
Click to collapse
GitHub - zainullahk/universal-pixelexperience-samsung: this is pixel experience by ponces think of this as a mirror but tailored to samsung devices
this is pixel experience by ponces think of this as a mirror but tailored to samsung devices - GitHub - zainullahk/universal-pixelexperience-samsung: this is pixel experience by ponces think of th...
github.com
Zainullahk1234 said:
it works on all models
Click to expand...
Click to collapse
HI.. Filthy iOS user here with minimal experience loading custo roms - I have the newer A13 that appears to be the A12 in a newer housing.. Will this work?
This Samsung bloat is is ridiculous
Sean2e said:
HI.. Filthy iOS user here with minimal experience loading custo roms - I have the newer A13 that appears to be the A12 in a newer housing.. Will this work?
This Samsung bloat is is ridiculous
Click to expand...
Click to collapse
u have an a13 and it says its an a12 doesnt make sense
dav1234444 said:
u have an a13 and it says its an a12 doesnt make sense
Click to expand...
Click to collapse
I meant in terms of hardware, My A13 uses the same exynos 850 & Mali gpu as the A12.
Compare Samsung Galaxy A12 (India) vs. Samsung Galaxy A13 - GSMArena.com
m.gsmarena.com
can someone send a screenshot of this rom?
sigpurnomo said:
can someone send a screenshot of this rom?
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Hidden User said:
Click to expand...
Click to collapse
hi I unlock boot loder my samsung a12 and flash twrp officall but i can not login to recovery for install this rom. now This page is displayed for me
imirsay said:
hi I unlock boot loder my samsung a12 and flash twrp officall but i can not login to recovery for install this rom. now This page is displayed for me
Click to expand...
Click to collapse
You should also flash vmbeta
Sheepmister said:
You should also flash vmbeta
Click to expand...
Click to collapse
ok thanks.
[AOSP-11] [OFFICIAL] Samsung SM-A125F TWRP
DISCLAIMER: I WAS NEVER, HAVE NEVER BEEN, AND WILL NEVER BE RESPONSIBLE OF ANY DAMAGES AGAINST YOUR DEVICES BY YOUR OWN MIS-OPERATIONS Install instructions: 1. Download an arbitrary SM-A125F firmware zip package on SamMobile.com, whose Android...
forum.xda-developers.com
imirsay said:
hi I unlock boot loder my samsung a12 and flash twrp officall but i can not login to recovery for install this rom. now This page is displayed for me
Click to expand...
Click to collapse
I installed TWRP by rooting then installing TWRP Official on the Play Store
Zainullahk1234 said:
Zainullahk1234 said:
install universal safteynet fix zygsik (magisk)to get safteynet working
enable denylist for apps you want to hide root from (dont enable it for google play services as it is not needed)
ALL credit goes to phusson , ponces and rest of the devsi
Click to expand...
Click to collapse
Click to expand...
Click to collapse
status bar and swip to unlock screan doesn't work and it gets fixed after a few seconds
Zainullahk1234 said:
What is this?
Pixel Experience is an AOSP based ROM, with Google apps included and all Pixel goodies (launcher, wallpapers, icons, fonts, bootanimation)
Our mission is to offer the maximum possible stability and security, along with essential and useful features for the proper functioning of the device
Based on Android 12.0 (11 is available but 12 has no difference in terms of issues and is faster an the better ui and everything else of course)
Disclaimer:- This will void warranty.
You will need to unlock bootloader.
*All your data will be lost*
Read all the steps correctly
BUGS:- bluetooth ear/headphones do not work workaround- ( go into phh treble settings misc features and enable force-disable a2dp offload (thanks to @Lil_Boudy for figuring it out!)
If bluetooth crashes your system disable media recommendations under Sound & Vibration > Media > Show media recommendations
mtp not working (mtp does work in twrp and in some custom kernels the one linked here does not fix mtp as it is not changing too many things compared to other custom kernels which brick some phones)
sim 1 incoming and outgoing does not work (you can revieve calls and call but you wonth hear anything nor will your mic go trying to fix) (workaround is to put your sim into slot 2) (i have heard that other people dont have this issue so i guess try your luck)
DO NOT let the phone die of battery you will not be able to boot you can get back by holding volume down and power (workaround- in magisk install acca https://github.com/Magisk-Modules-Repo/acc and install this apk after installing https://github.com/MatteCarra/AccA then set profile to default (this will shut down the phone at 5% hence removing the risk of your phone not booting after hitting 0%
You tell me
Links
Source (Kernel Source)
https://github.com/topjohnwu/Magisk/files/7819803/app-debug.zip (magisk)
Rom download.
1.Need TWRP 3.4.0 or higher!
2. Unpack the "xz" archive and put the .img file onto the sd card or internal (if you dont have a sd card do step 3 then transfer the img file to your phone)
3. In TWRP head to factory reset format type yes and hit enter
4. Flash the img file (as system obviously)
5 install magisk (the one linked above only) (optional but you should as a lot of modules are listed here are very important (ie the acc module and the fast charging module)
5.5.Reboot and enjoy!
Zainullah Boot fix (if you cant boot)
install oneui boot into oneui change date to 3 months from now
check for updates
boot into download mode
flash twrp 3.6.0 and vbmeta
boot into twrp
do format data
flash multidisabler
flash rom
flash kernel as boot
do factory reset
reboot
if it boots you into fastboot shutdown flash twrp only and try another factory reset and reboot (In twrp)
Install Gcam go by greatness from here
https://www.celsoazevedo.com/files/android/google-camera/dev-greatness/f/dl9/
also enable extra cameras in phh treble settings - samsung settings for ultrawide
Increase performance without any battery impact or (by feravolt and gloeysik)
Step 1
- Uninstall ANY OTHER KERNEL MANAGER app including smartpack/Ktweaks to avoid conflict, since this app uses AI and machine learning to dynamically boost performance when needed
- Install FDE AI Magisk Module to make it a system app, thus it will work better and removes all kernel locks from OEMs (I'm looking at you, Samsung) https://github.com/feravolt/FDE.AI-docs/releases/download/12.4.1m/FDE.AI-as-system-app.MAGISK.zip
- Update FDE AI to the latest version by downloading the latest APK here, since the fde ai magisk module will only install fde ai 12.4.1, not the latest version: https://github.com/feravolt/FDE.AI-docs/releases
- Move to the bottom of the screen and select AI Chat, then type /advancedai (no space, no uppercase letters). This will going to make the AI more effective, without you having to do anything.
- Go to the settings tab and use the AUTO settings for FDE AI.
Optimized and adjusted Google Play services. Contribute to gloeyisk/universal-gms-doze development by creating an account on GitHub.
github.com
install cloudflaredns4magisk (install both ipv4 and ipv6 versions) (this will switch you to cloudflares faster and more secur dns
Cloudflare dns magisk download
install adaway (optional if you want ads or not) , allow superuser for it download this https://energized.pro/bluGo/formats/filter in adaway click he button in the middle click add click file and add the file then go back to the main menu and click the reload button now https://adaway.org/
(you get better battery and performance in adaway)
also enable extra cameras in phh treble settings - samsung settings for ultrawide
install universal safteynet fix zygsik (magisk)to get safteynet working
enable denylist for apps you want to hide root from (dont enable it for google play services as it is not needed)
ALL credit goes to phusson , ponces and rest of the devs
Blog
Pixel Experience
Donate
jhenrique09
phhusson
AndyYan
eremitein
ponces
Click to expand...
Click to collapse
When I unlock the screen with my fingerprint. The touch screen does not work for a few moments.
Zainullahk1234 said:
DO NOT let the phone die of battery you will not be able to boot you can get back by holding volume down and power (workaround- in magisk install acca https://github.com/Magisk-Modules-Repo/acc and install this apk after installing https://github.com/MatteCarra/AccA then set profile to default (this will shut down the phone at 5% hence removing the risk of your phone not booting after hitting 0%
Click to expand...
Click to collapse
If the phone is turned off, will the data be deleted?
Can you explain more for beginners like me?
I turned on the phone screen in this video. See the delay in execution.