I tried to install superSu via samsung odin, but it says there is no pit partition. Someone told me that I need pit file for recovering it. Where can I find it?
Are there anyother solution for this?
kegang said:
I tried to install superSu via samsung odin, but it says there is no pit partition. Someone told me that I need pit file for recovering it. Where can I find it?
Are there anyother solution for this?
Click to expand...
Click to collapse
There is no pit partition. The pit file is a file that describes the partitions on your phone for Odin. It's stored inside your Bootloader but you don't have to worry about that.
If your flashing from Odin it will use your current pit for flashing. If you are installing a new stock rom a pit file comes with it inside the CSC .tar.md5
partcyborg said:
There is no pit partition. The pit file is a file that describes the partitions on your phone for Odin. It's stored inside your Bootloader but you don't have to worry about that.
If your flashing from Odin it will use your current pit for flashing. If you are installing a new stock rom a pit file comes with it inside the CSC .tar.md5
Click to expand...
Click to collapse
I tried to flash a new stock rom, but same problem.
Should I try for another stock rom?
kegang said:
I tried to flash a new stock rom, but same problem.
Should I try for another stock rom?
Click to expand...
Click to collapse
I don't follow what you mean. Please reread what I said. Pit files are in every single stock rom, inside the CSC_OYM archive
partcyborg said:
I don't follow what you mean. Please reread what I said. Pit files are in every single stock rom, inside the CSC_OYM archive
Click to expand...
Click to collapse
I think the problem is solved. I flashed another version of rom and, everything is good thank you!
Related
PDA/PHONE/CSC files
Hello, I was following the instructions one by one to flash my phone.
Also downloaded the latest firmware from sammobile.com/firmware
The firmware consists of a .tar.m5 file of size around 350mb.
but now they ask me to browse to the CSC, PDA AND PHONE files.
Which are these? and where can I get those?
Thanks.
If your rom have one file then flash with odin as PDA.
Here is instruction http://forum.xda-developers.com/showthread.php?t=1133787
umarian said:
If your rom have one file then flash with odin as PDA.
Here is instruction http://forum.xda-developers.com/showthread.php?t=1133787
Click to expand...
Click to collapse
The rom i downloaded has two files in it,
one is
I9003DDKP2_I9003ODDKPH_I9003DDKP4_HOME.tar.md5
and other is
SS_DL.dll
I'm naive to this.
Please help.
Thanks.
This file : I9003DDKP2_I9003ODDKPH_I9003DDKP4_HOME.tar.md5 put in PDA with Odin and push start. NO select in odin Re-Partition.Again say NO select Re-Partion
umarian said:
This file : I9003DDKP2_I9003ODDKPH_I9003DDKP4_HOME.tar.md5 put in PDA with Odin and push start. NO select in odin Re-Partition.Again say NO select Re-Partion
Click to expand...
Click to collapse
I don't have to do the step having the PIT file thing then?
shalin99 said:
I don't have to do the step having the PIT file thing then?
Click to expand...
Click to collapse
Now currently which firmware are you using...?
Just put the .tar file in pda and flash it with re-partition unchecked.
Pit file is for base version of gb which is xxkpe. Here you dont need this.
please click thanks if you helped me.... ( oops sorry if i held you )
got new galaxy i9003 on replacement.....
ddkp2/ext4/cwm 5
Thanks guys. Successfully flashed my phone.
shalin99 said:
PDA/PHONE/CSC files
Hello, I was following the instructions one by one to flash my phone.
Also downloaded the latest firmware from sammobile.com/firmware
The firmware consists of a .tar.m5 file of size around 350mb.
but now they ask me to browse to the CSC, PDA AND PHONE files.
Which are these? and where can I get those?
Thanks.
Click to expand...
Click to collapse
ffrm can in download those files?
Hi. Obviously i did something wrong with flashing cwm (wiping made my tab confused? ) and now i need the 3 Part Firmware. I flashed the Firmware with odin but it doesnt boot.
Thanks for your help
Anybody?
i found a Honey Comb 3-Part Firmware...
... can i flash it over my f.... uped ICS....???? Thanks a million
siqChris said:
... can i flash it over my f.... uped ICS....???? Thanks a million
Click to expand...
Click to collapse
just out of curiousity, what is this 3 part firmware?
i have a file called P6200XXLQ1_P6200OXALQ1_ATO.zip which contains a file called P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5 that can be flashed with odin.
wingie6200 said:
just out of curiousity, what is this 3 part firmware?
i have a file called P6200XXLQ1_P6200OXALQ1_ATO.zip which contains a file called P6200OXALQ1_P6200XXLQ1_P6200XXLQ1_HOME.tar.md5 that can be flashed with odin.
Click to expand...
Click to collapse
The 3 part Firmware contains pit, modem etc
Flashing the one part FW (maybe the one you´ve got) is successfull. So it might be a problem with pit...
unfortunately i´m not quite sure if i explain it right...
actually.. the tar.md5 is the actual firmware that you need to flash via odin.
The pit file is called the partition information table. This contains the information that odin needs to repartition your device if it has some major issues with it.
during the flashing procedure for upgrading to HC or ICS the pit file is not really needed - there is no repartitioning necessary (if your tab is working properly)...
its only needed in a dead device for recovery purposes (to my understanding at least).
Thats the problem: the Tablet is not working. I can flash the 1 Part Firmware with the download mode but it doesnt boot. Somebody told me, that i need a 3 Part Firmware
How to go back to my old ddlf2 firmware from new cm9 EXT4 partition.......
Flash pit.latona file first. then xxkpe and then ddlf2....
Full flashing info is hereforum.xda-developers.com/showthread.php?t=1133787.
Only problem is that i dont know whether to flash pit file with re-partition or without re-partition.
Where is the pit.latona file
androman1507 said:
Flash pit.latona file first. then xxkpe and then ddlf2....
Full flashing info is hereforum.xda-developers.com/showthread.php?t=1133787.
Only problem is that i dont know whether to flash pit file with re-partition or without re-partition.
Click to expand...
Click to collapse
Where is the link for pit.latona file file??????????
^^ It's in the xxkpe zip file. You'll see 4 files. You'll need to follow the guide to flash all 4 files using ODIN.
Everything was fine. tried the minuit (or however you spell it) mod. Ended up in a boot loop. i can get into download mode fine. Downloaded the stock firmware to odin back and start over, but when i try, it checks the MD5 just fine. starts the "setupconnection" then i get a fail "can't open the serial(COM) port.
Am i doing something wrong here? Any help at all would be greatly appreciated!
What firmware version were you on before bootloop and what version are you trying to ODIN?
jlaholton said:
Everything was fine. tried the minuit (or however you spell it) mod. Ended up in a boot loop. i can get into download mode fine. Downloaded the stock firmware to odin back and start over, but when i try, it checks the MD5 just fine. starts the "setupconnection" then i get a fail "can't open the serial(COM) port.
Am i doing something wrong here? Any help at all would be greatly appreciated!
Click to expand...
Click to collapse
You need odin 3.10.6 and make sure you downloaded the latest stock firmware .tar. when flashing, don't move the phone, cord or laptop (if thats what you have).
Sent from my SM-G925P using XDA Free mobile app
Me too. The odin stuck at <ID:0/010> NAND Write Start!!
My stock ROM is OE2 and want to flash OF7, the original stock ROM has been rooted and TWRP installed.
lwang9 said:
Me too. The odin stuck at <ID:0/010> NAND Write Start!!
My stock ROM is OE2 and want to flash OF7, the original stock ROM has been rooted and TWRP installed.
Click to expand...
Click to collapse
Wipe system and try again
Soooperstar said:
Wipe system and try again
Click to expand...
Click to collapse
TWRP has been replaced to the original recovery firmware. It couldn't read the internal storage.
lwang9 said:
TWRP has been replaced to the original recovery firmware. It couldn't read the internal storage.
Click to expand...
Click to collapse
Are you able to factory reset from stock recovery?
Soooperstar said:
Are you able to factory reset from stock recovery?
Click to expand...
Click to collapse
I failed to use ODIN flash the entire stock ROM which is over 3gb tar.md5 file. Could I download the stock recovery only and flash by ODIN? Also, I am not sure if PIT file helps. I couldn't find PIT file download yet.
lwang9 said:
I failed to use ODIN flash the entire stock ROM which is over 3gb tar.md5 file. Could I download the stock recovery only and flash by ODIN? Also, I am not sure if PIT file helps. I couldn't find PIT file download yet.
Click to expand...
Click to collapse
Not completely understanding you. Are you saying Odin is failing when trying to Odin latest firmware?
Yes, I failed to flash the latest firmware by ODIN 3.10. I read another post mentioned PIT file to flash to avoid this issue. However, I don't know where I could download the PIT file for this phone.
lwang9 said:
Yes, I failed to flash the latest firmware by ODIN 3.10. I read another post mentioned PIT file to flash to avoid this issue. However, I don't know where I could download the PIT file for this phone.
Click to expand...
Click to collapse
Are you on the latest Odin version and are you using the correct firmware?
Yes, I did.
lwang9 said:
Yes, I did.
Click to expand...
Click to collapse
What Odin version are you using? What phone do you have, and what firmware version are you trying to use? What firmware are you on now?
Soooperstar said:
Are you on the latest Odin version and are you using the correct firmware?
Click to expand...
Click to collapse
My Odin version is 3.10 and the firmware I downloaded from Sammobile.
sammobile.com/firmwares/download/50549/G925PVPU2BOF7_G925PSPT2BOF7_SPR/
lwang9 said:
My Odin version is 3.10 and the firmware I downloaded from Sammobile.
sammobile.com/firmwares/download/50549/G925PVPU2BOF7_G925PSPT2BOF7_SPR/
Click to expand...
Click to collapse
And you have the sprint s6 edge? You didn't answer all my questions
used one of these when i had recent problem.
edit: try to use the same firmware your currently on (what i did) and the thing that worked for me was using an older sammy usb cable. Beleive it or not the original one kept failing on me. i had a thicker black one that was from my s4 maybe or note 2 i think and used that one and boom went thru. good luck
los82 said:
edit: try to use the same firmware your currently on (what i did) and the thing that worked for me was using an older sammy usb cable. Beleive it or not the original one kept failing on me. i had a thicker black one that was from my s4 maybe or note 2 i think and used that one and boom went thru. good luck
Click to expand...
Click to collapse
Thanks!!! It worked. Just grab another USB cable. The original one kept failing on me either. The issue has been solved. Thanks again.
Hello XDA!
I have a S3 I535 bricked on the "downloading mode", no matter what I do it always ends on the download screen, no way to access to recovery. I have tried with Odin, Heimdall and all advices in this and other forums.
The error is always the same:
Heimdall
=======
Without repartition:
ERROR: Failed to receive PIT file size!
ERROR: Failed to download PIT file!
With repartition:
ERROR: Failed to confirm end of PIT file transfer!
ERROR: PIT upload failed!
Odin
====
With and without repartition:
<ID:0/010> Get PIT for mapping..
<ID:0/010> There is no PIT partition.
In the phone: "Odin : flash read failure"
I'm using the right SCH-I535 PIT file (16Gb)
As I understand, these programs need the PIT information to write at the right address in the memory map of phone. Right? But for some reason my cell can't provide it or change it. However there are ways to "read" the PIT file and get the "base address" for a specific partition. The question: there is a way to force Odin, Heimdall or fastboot to flash a particular image partition to its known address?
Something like this:
heimdall flash --recovery recovery.img --base 0x1234abcd
Is it possible, would it works and solve my problem?
Thanks!!
what tar.md5 are you trying to flash? I hardbricked one of these a while back and had to use the debrick.img to fix it, but if you can get to DL mode, then you shouldnt be THAT boned... yet...
youdoofus said:
what tar.md5 are you trying to flash? I hardbricked one of these a while back and had to use the debrick.img to fix it, but if you can get to DL mode, then you shouldnt be THAT boned... yet...
Click to expand...
Click to collapse
A 4.4.2 stock rom from: gsm-file
I already tried debrick images, nothing changes. It always fail on PIT step.
Thanks
mikefncu said:
A 4.4.2 stock rom from: gsm-file
I already tried debrick images, nothing changes. It always fail on PIT step.
Thanks
Click to expand...
Click to collapse
youre trying to odin a tar.md5 built for a different phone? i ask because i dont understand what you mean by "from: gsm-file"
youdoofus said:
youre trying to odin a tar.md5 built for a different phone? i ask because i dont understand what you mean by "from: gsm-file"
Click to expand...
Click to collapse
Sorry, gsm-file is a website with stockroms, google it, I can't put the link because Im a new member.
mikefncu said:
Sorry, gsm-file is a website with stockroms, google it, I can't put the link because Im a new member.
Click to expand...
Click to collapse
oh, no worries. have you tried getting the file from www.sammobile.com/firmwares ? its the most legit source for the file, takes FOREVER, but its from the source. You might have bad downloads