Related
Purchased an Lg Gpad 7 Wifi tablet (v400) 2 weeks ago. Came with preinstalled Lollipop android so i couldnt install a recovery rom to flash any other custom roms. Downgraded to Kitkat version following the instructions on Xda forums and succesfully installed Twrp. When i installed Cyanogenmod 12.1 through Twrp i got stuck in fastboot screen.
Any suggestions and / or solutions would be greatly appreciated.
I had a similar problem.. Only mine was stuck at the bootloader. Go in TWRP and repair /data and other partitions. My data partition gave me an error since F2FS is a little flaky and some ROMs corrupted it (claimed they supported it). I would recommend erasing the system, cache and data partition if you can't get into TWRP.
The problem is i cant get out of fastboot whatever i try. It says start on bootloader but the tablet just restarts on an empty screen doing nothing.
Hakalai said:
The problem is i cant get out of fastboot whatever i try. It says start on bootloader but the tablet just restarts on an empty screen doing nothing.
Click to expand...
Click to collapse
if you have an sd card, try removing that, then reboot.
if that doesnt work, try entering fastboot command, fastboot continue
Tried without sdcard and i get the same fastboot screen.
How can i give any commands? The only options i have are Restart Bootloader / Restart / Power off. Tried restarting bootloader but i get nothing in return tablet just stays on with nothing on screen.
Hakalai said:
Tried without sdcard and i get the same fastboot screen.
How can i give any commands? The only options i have are Restart Bootloader / Restart / Power off. Tried restarting bootloader but i get nothing in return tablet just stays on with nothing on screen.
Click to expand...
Click to collapse
you said it was stuck on fastboot, if thats the case, install any needed drivers on your pc, connect device to it, open a terminal in the fastboot dir (after you go get fastboot), then try those commands i gave. you could also try, fastboot reboot dont think i mentioned that before.
bweN diorD said:
you said it was stuck on fastboot, if thats the case, install any needed drivers on your pc, connect device to it, open a terminal in the fastboot dir (after you go get fastboot), then try those commands i gave. you could also try, fastboot reboot dont think i mentioned that before.
Click to expand...
Click to collapse
Did as you said but every command i gave gives me an error message in adb terminal. There are new lines in fastboot menu in tablet now. Bottom two are SECURE BOOT - enabled & LOCK STATE - locked.
Hakalai said:
Did as you said but every command i gave gives me an error message in adb terminal. There are new lines in fastboot menu in tablet now. Bottom two are SECURE BOOT - enabled & LOCK STATE - locked.
Click to expand...
Click to collapse
hmm, ok, im guessing it would have said that normally, when not broken. all the command does is try to release it past where its stuck. it doesnt actually flash, lock, unlock, or change anything.
imo, this seems good, because now we know fastboot is working.
i own lg devices, but not your specific device. i would hate to give you some bad advice and make your tablet broken more, but if it were me in this situation, i would try to flash the factory KK firmware you used to downgrade with odin or however you did it. hopefully, that will clean everything up and let it boot properly.
if for whatever reason you cant do that, we could try extracting the factory file, and just flashing recovery and system, those should be the only things that got changed putting on twrp and cm normally.
Sorry, I have the serious proplem wtih my LG pad V400, I rooted it and using <LG Flash Tool 2014> with <V40010c_00.kdz> to downgrate the firmware but their is error then my LG pad stuck in fastboot menu as with just turn off, restart and restart bootloader. if i seclect one one them the tablet just logged again the fastboot menu
it stuck on the fastboot menu and i cannot do nay think with it. I can restart with factory restore mode but when select yes to restore, it will restart and log in fastboot menu again.
I downloaded adb and fastboot program and put in one folder <Minimal ADB and Fastboot> in C:\Program Files (x86)\Minimal ADB and Fastboot
I dont have recovery image so i download file <cm-13.0-20160421-NIGHTLY-v400-recovery.img> form your link to download TWRP file
move it to folder of fastboot programe and changed its name to <recovery.img>
I turn on the tablet and it waited at fastboot menu
when i run the command <fasboot flash recovery recovery.img> and they said some thing wrong like in picture
please help me
So I had an unlocked H8 with LOS. As I wanted to install EMUI, I put the proper restore Update.app into the dload folder and started Huawei's recovery. Everything went well, I formated data and wanted to install the EMUI 4.1 ROM using the same method.
Unfortunately my H8 is bootlooping and there is now way into erecovery nor any other recovery. It simply reboots on every single known vol up or down key pressing combination. The only thing I can go to is fastboot mode when holding down vol down and plugging in usb wire. But, it says frd locked and I can't install nor boot twrp. It's simply gone and reboots all the time.
Any hints? I can't even turn it off.
I wanted to give away that phone that's the reason. Last time I did it this way, I could flash the EMUI 4.1 since it's signed. But not this time.
Interesting part is, that although fastboot says frd locked, I still get the "phone unlocked" warning on every reboot. dload method isn't working, as it simply keeps rebooting.
It's my hardest brick so far I ever encountered
the same thing happened to me.....on my phone lock/unlocked frp and bootloader were tweaked for some reason(I mean that what was written wasn't the reality) so how did I fix it? I kept on to flash rollback package many times and I tried to unlock/relock bootloader again, at the end the phone let me to flash the firmware, I didn't know how but the phone allowed me to flash things throw recovery(using dload method). At the begin I only could access to erecovery and fastboot. I suppose that I broke system and data partition and while I looked/unlocked the bootloader, the wipe fixed the partition table. Sorry I'm tired and I know that my English sucks, I hope you understand what I have written.
How did you enter erecovery as this isn't working for me.... What did you flash over fastboot?
Have you tried flashing the firmware separately using adb on computer?
For this you just need to extract the Update.app using the firmware extractor for huawei. Then flash them individually using adb commands in cmd.
I can't access any state that would allow to do adb.
faeArai said:
How did you enter erecovery as this isn't working for me.... What did you flash over fastboot?
Click to expand...
Click to collapse
sorry. I'll try to explain better, however on Huawei/honor devices there are not one but two recoveries, so one is the normal recovery flashed in recovery partition, the second one is the Huawei recovery that is flashed in recovery2 partition, so if you didn't touch recovery2 partition, your erecovery is still there, now, if you press VOL+ VOL- and POWER it will reboot to recovery2 and it starts to flash something from dload in your sd card, so in my opinion you should do this things, first try this method to flash rollback package(this is the transition package from 7 to 6 and you will find it on honor site) if this is still not working try locking and unlocking again your bootloader(I hope this fix partitions of your device) then try to enter recovery and do a wipe and then boot your device, if this doesn't work flash rollback package(now it would work) and then flash an emui 4 full firmware image, always using dload method. trust me... I did the same... and it worked for me. let me know if it works for you :good:
faeArai said:
So I had an unlocked H8 with LOS. As I wanted to install EMUI, I put the proper restore Update.app into the dload folder and started Huawei's recovery. Everything went well, I formated data and wanted to install the EMUI 4.1 ROM using the same method.
Unfortunately my H8 is bootlooping and there is now way into erecovery nor any other recovery. It simply reboots on every single known vol up or down key pressing combination. The only thing I can go to is fastboot mode when holding down vol down and plugging in usb wire. But, it says frd locked and I can't install nor boot twrp. It's simply gone and reboots all the time.
Any hints? I can't even turn it off.
Click to expand...
Click to collapse
I ran into this issue not that long ago. What you have to do is relock your bootloader using ADB. The ADB commands and instructions can be found in this thread.
Just a FYI, do not use the links to the software listed in that thread as it is a little outdated. The method still works but the software will probably not work. Just be sure to get the most recent/appropriate version of SuperSU and TWRP via their official threads (This is if you want to re-root). There are Honor 8 specific TWRP files if I remember correctly, so be sure to check around the Honor 8 forums for the correct files.
A quick summary of what I did:
1) Power your phone off and then boot into fastboot by holding Vol down + Power; as soon as it boots up, plug your phone into your combuter via your usb cord.
2) With ADB running, type:
Code:
fastboot oem relock [COLOR="LightBlue"]################[/COLOR]
NOTE: The '#' should be replaced with your unique unlock code that you obtained to unlock your bootloader.
3) Wait for it to format and reset your phone and go through the setup. BE SURE TO BYPASS all google registration; skip everything you can to get into the phone itself. If you do register, it will reactivate FRP and you'll have to start over again.
4) Turn on USB Debugging and every other setting that enables developer administrative navigation and control just to be safe. USB Debugging being the most important one, though.
5) Restart your phone and boot into fastboot again using Vol down + Power.
6) Unlock your phone again with:
Code:
fastboot oem unlock [COLOR="LightBlue"]################[/COLOR]
7) Once the command is entered, it'll reset your phone once more and - as stated before - bypass/skip all google (FRP) registration.
8) Enable developer options and USB debugging again and make sure that OEM Unlocked is checked and grayed out.
9) Reboot into fastboot mode to confirm that FRP is disabled and you should be able to install TWRP now via ADB.
@Numerics thanks. The thing is, that I can't boot anything. I can't even go into eRecovery. Nor can I flash a stock EMUI 4.1. It just boot loops all the time and I can only access fastboot.
If you can flash twrp..........Install los or other Rom ..................Go back to stock.......you must flash b360 ober adb...... because los is 7.1...............if you on b360 you can usw the rollback for emui 4.1........,..............sry for bad english
I can easily go to fastboot. But I can't flash anything. I extracted the img from the update.app but can't flash. It simply says that it's not permitted.
faeArai said:
I can easily go to fastboot. But I can't flash anything. I extracted the img from the update.app but can't flash. It simply says that it's not permitted.
Click to expand...
Click to collapse
With my method, you don't need to flash anything. Just relock your bootloader via adb in fastboot mode and let it reset. Unless I'm not understanding your issue entirely.
@Numerics as I said, in won't boot anything as it is constantly boot looping. There is no way to access any kind of recovery nor erecovery. There is no boot into Android. The only thing accessible right now is fast boot (which is not ADB). But even in fast boot I can't do anything als operations are not permitted.
after boot looping and starting fast boot mode, I can see a "Android reboot reason" section saying:
AP_S_PANIC
data is invalid
There is still a lineageos installed on system as firmware but as I tried to get rid of it by going back to stock EMUI, I guess Huawei's rollback did something wrong and killed recovery (although I did it in the past successfully).
I tried to run HiSuite to recover my phone, but it just says, that my phone is not supported.
Speaking of this, Huawei messed up with that whole fastboot locking bull****.
faeArai said:
@Numerics as I said, in won't boot anything as it is constantly boot looping. There is no way to access any kind of recovery nor erecovery. There is no boot into Android. The only thing accessible right now is fast boot (which is not ADB). But even in fast boot I can't do anything als operations are not permitted.
after boot looping and starting fast boot mode, I can see a "Android reboot reason" section saying:
AP_S_PANIC
data is invalid
There is still a lineageos installed on system as firmware but as I tried to get rid of it by going back to stock EMUI, I guess Huawei's rollback did something wrong and killed recovery (although I did it in the past successfully).
I tried to run HiSuite to recover my phone, but it just says, that my phone is not supported.
Speaking of this, Huawei messed up with that whole fastboot locking bull****.
Click to expand...
Click to collapse
No, I know ADB isn't Fastboot. What I'm trying to say is that you should be able to still run ADB via CMD on Windows when you're in fastboot mode to relock your bootloader with the directions I gave in my previous post. It'll force-restore your phone to a non-bricked/vanilla state. At least that is how I fixed mine.
Like... You can't even try using the 'fastboot oem relock ################' function via the ADB console while in fastboot?
yes boy trust us, you haven't a working OS so it is a normal thing that your phone reboot, you cannot access to recovery because some partitions are corrupted (data partition) , so these are the steps that could help you:
1) using fastboot, relock your boot loader
2)using fastboot, unlock your boot loader (partition table would be ok now, and you would be able to use load method to flash things trow stock recovery)
4)put inside your sd card \dload\update.app(use rollback package)
3) press all the buttons while your device is rebooting(do this before the blue screen logo appear), your phone is now looking for something inside your sd card
5) if the next step doesn't work do a factory reset from recovery that now would be working
6) put inside your sd card a full android 6 (emus 4) update.app and pressing all buttons it will install the firmware
7) your device now is locked and back to stock, maybe without cust partition or maybe in test mode but it is certainly alive
8) do a factory reset and reinstall the firmware
9) your phone is now ok
You don't lock the bootloader via ADB but via fastboot.
As I said, northing was restored and nothing is booting and I can't unlock my bootloader again. As I said, recovery is not working so the file in dload is not loaded and used. Which is strange.
Locking bootloader didn't do anything besides locking the bootloader. Device is still dead and I still can only access fastboot.
faeArai said:
You don't lock the bootloader via ADB but via fastboot.
As I said, northing was restored and nothing is booting and I can't unlock my bootloader again. As I said, recovery is not working so the file in dload is not loaded and used. Which is strange.
Locking bootloader didn't do anything besides locking the bootloader. Device is still dead and I still can only access fastboot.
Click to expand...
Click to collapse
Which model do u own?
Sent from my Honor 8 using XDA Labs
The European one.
faeArai said:
You don't lock the bootloader via ADB but via fastboot.
As I said, northing was restored and nothing is booting and I can't unlock my bootloader again. As I said, recovery is not working so the file in dload is not loaded and used. Which is strange.
Locking bootloader didn't do anything besides locking the bootloader. Device is still dead and I still can only access fastboot.
Click to expand...
Click to collapse
This is not the truth.....locking bootloader will erase all your data and fix partitions....and with fixed partition you can access to recovery ......trust me the only thing that you can do is to lock your bootloader......you can't flash anything from fastboot and boot recovery or system now...... lock your bootloader and then unlock it again, try using "fastboot OEM lock *****" or "fastboot OEM relock *******" (try cmd runned as admin, people say that this makes the difference) then unlock your device again and .....magic your recovery will boot......the same thing happened to me and I fixed my phone using this trick, however, even if you had frp unlocked it would say you that isn't possible to write anything because you broke some partition, and that's the reason why you can't boot recovery, wait one second and think: why doesn't my recovery boot?
It has nothing to do with trust. I did it and device is still a full stone brick. Nothing changed by locking the bootloader besides that now I can't unlock the bootloader anymore.
Hello
I have a Google pixel 128 GB device but recently it got bricked after an ota update. Unfortunately my phone is not rooted or unlocked. So I could not do anything under fastboot, also adb is crashed.
So the phone is bricked. But it can be rectified using QPST is edl mode I suppose. But as of now there is no such development for qpst for Google pixel.
But there are many users they face the same issue recently.
Is there any chance of development for it?
you said bootloader ! you mean the phone can boot into bootloader mode ! after that you said edl mode ? i dont understand. please explain. i may help !
*The Phone Goes into Fastboot with no problems.
*In Fastboot Mode if i try to go to Recovery, The Phone Reboots and does not go to the Recovery But it Keeps on Rebooting.
So the Recovery Partition of the Phone might be Corrupted.
So im looking for ways to Flash the Recovery partition with QPST or any other methods.
Fastboot Doesn't Help Because the Bootloader is locked.
senthil19 said:
*The Phone Goes into Fastboot with no problems.
*In Fastboot Mode if i try to go to Recovery, The Phone Reboots and does not go to the Recovery But it Keeps on Rebooting.
So the Recovery Partition of the Phone might be Corrupted.
So im looking for ways to Flash the Recovery partition with QPST or any other methods.
Fastboot Doesn't Help Because the Bootloader is locked.
Click to expand...
Click to collapse
Download factory image, open up the .sh script as text, copy the fastboot commands about wiping and clearing userdata, cache , etc into a terminal using fastboot
Xdevillived666 said:
Download factory image, open up the .sh script as text, copy the fastboot commands about wiping and clearing userdata, cache , etc into a terminal using fastboot
Click to expand...
Click to collapse
I do believe I've tried this to no avail on a Verizon g-2pw4100-022-b (the "b" probably stands for "brickable").
I'm stuck in the same situation:
Power+vol down - bootloader
Bootloader to recovery - boot loop
Bootloader to barcodes - barcodes show
Edit: power on only leads to constant screen flashing unless you hold volume down for bootloader, at which point you can vol up once and power down.
Can't flash a recovery, can't flash an OTA since that requires adb sideload, which is part of recovery, and can't flash a factory image with the bootloader locked, which is only unlocked under development tools.
One thing to note is that in the bootloader screen, both "b/l" and the one below it (radio?) both say "n/a", which leads me to believe the December update from Verizon could be the cause.
Suggestions as to how to proceed are greatly appreciated.
senthil19 said:
Hello
I have a Google pixel 128 GB device but recently it got bricked after an ota update. Unfortunately my phone is not rooted or unlocked. So I could not do anything under fastboot, also adb is crashed.
So the phone is bricked. But it can be rectified using QPST is edl mode I suppose. But as of now there is no such development for qpst for Google pixel.
But there are many users they face the same issue recently.
Is there any chance of development for it?
Click to expand...
Click to collapse
I have a Reddit thread how to activate qpst .
You can also "adb reboot edl" if your PC can recognize your phone at least.
If not, power button and volume up(or down, I don't remember) for at least forty seconds sometimes brings it up
But then you'd need firmware to flash with qpst and I'm not sure how to go about doing that
---------- Post added at 07:44 AM ---------- Previous post was at 07:42 AM ----------
PoXFreak said:
I do believe I've tried this to no avail on a Verizon g-2pw4100-022-b (the "b" probably stands for "brickable").
I'm stuck in the same situation:
Power+vol down - bootloader
Bootloader to recovery - boot loop
Bootloader to barcodes - barcodes show
Edit: power on only leads to constant screen flashing unless you hold volume down for bootloader, at which point you can vol up once and power down.
Can't flash a recovery, can't flash an OTA since that requires adb sideload, which is part of recovery, and can't flash a factory image with the bootloader locked, which is only unlocked under development tools.
One thing to note is that in the bootloader screen, both "b/l" and the one below it (radio?) both say "n/a", which leads me to believe the December update from Verizon could be the cause.
Suggestions as to how to proceed are greatly appreciated.
Click to expand...
Click to collapse
Can you fastboot boot twrp ?
Are there any solutions to enter EDL Mode in google pixel without adb?
I just tried rooting my phone. The phone is cycling back and forth between the bootloader is unlocked screen and the Motorola splash screen.
To repeat some steps from a prior post.
My phone had QPR30.80-58-3 .
I downloaded that ROM and extracted the boot.img file.
I downloaded the latest Magisk Manager and installed it on my phone.
I ran through the patching process for boot.img.
I requested an unlock code from Motorola and unlocked the bootloader.
I flashed the patched boot image which patched partition b.
I flashed the patched boot image to partition a.
I rebooted which began the cycle.
I tried holding down the power button but it returns to the cycle.
I can get back to the bootloader with the Volume Down and Power buttons.
Any suggestions on what could get me back to a functioning phone, rooted or not rooted?
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
dafunk60 said:
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
Click to expand...
Click to collapse
I checked that the image I patched was from the QPR30.80-58-3 ROM which matched the level after the phone was updated.
I flashed that original boot image which flashed partition a and then rebooted. I did not flash partition b.
It first came up with the unlock warning screen. It sat on the Motorola splash screen for a noticeable amount of time followed by a yellow screen with a circle around the Motorola symbol. Finally it ended up on a blue Hello there screen with a yellow start button.
This screen was unresponsive. Eventually through various cyclings through all this I ended up on a screen that said Android could not boot and gave me an option of a factory reset. I did that but it did not help getting past the Hi there screen.
I went back and flashed the QPR30.80_58 image on both partitions a and b. This got me back to setting up the phone again. The phone is at QPR30.80_58. I am considering just rooting at this level.
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
DougPeterson said:
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
Click to expand...
Click to collapse
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
dafunk60 said:
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
Click to expand...
Click to collapse
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If you want to get into recovery, boot into the bootloader than do
Code:
fastboot reboot fastboot
That'll boot you into fastbootd which has an option to go to the real recovery
DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If adb isn't showing any devices connected that would explain why the rescue software cannot find your phone. Perhaps you don't have the correct driver installed. Windows Device Manager shows the phone as a Motorola ADB Device on my PC.
View attachment 5061327
Another possibility is that you have multiple versions of adb on your PC. Older versions won't work but the adb.exe in "C:\Program Files (x86)\Rescue and Smart Assistant" works for sure. With your phone booted into android & unlocked, plug it into your PC. Do you see the "USB debugging connected" on the phone? If you don't I would re-check that USB debugging is enabled. If you do see the debugging notification, on your PC, open a command prompt and navigate to "C:\Program Files (x86)\Rescue and Smart Assistant". Run
Code:
adb devices
Does adb find your phone?
Good morning!
While attempting to flash a stock MIUI 10 ROM into my Xiaomi Redmi Note 7, to downgrade back to Android 9.0 due to some app compatilibty issue, I messed up big time and my phone is now stuck in a loop where the screen turns on, nothing shows up, then it restarts, going off for a few seconds and turning on again.
Power Button + Volume UP successfully brings me to the stock recovery 3.0 from xiaomi.
Power Button + Volume DOWN fails to bring me to the fastboot mode.
If I select the Connect with MIAssistant in the recovery the phone will show up as "sideloaded" after using the command adb devices, but the MIPCSuite app does not see it and the command adb restart bootloader also fails to bring up the fastboot mode, it just gets stuck in the loop again.
More context on what went wrong and caused this: I followed an online tutorial to flash a rom using the MIFlash app, so I unlocked the bootloader and tried to flash the rom usin xiaomi's tool. I got a failed to check sparse crc error code and it went downhill from there when I tried to fix things reading multiple threads on the issue. I tried deleting some lines from the flash_all.bat file and tried to flash it again but then the flashing process went seemingly forever so I aborted the operation and now this loop happens. I tried a few more times but with no success.
The first time I tried to use the tool I used the clean all and lock option so I'm not certain if the miflash tool locked the bootloader regardless of the outcome of the flashing attempt.
Is there hope? Can I fix this phone if I only have access to stock recovery and nothing else (although it shows up in adb devices but can't get into fastbootmode) ?
Thanks a lot to anyone who took the time to read and possibly help.
Both ADB and Fastboot are Android-side launched by device's bootloader. If you can't enter Fastboot mode then my guess is there is something is wrong with curently installed Android.
BTW: If you lock device's bootloader then bootloader attempts to load device's Stock ROM.
jwoegerbauer said:
Both ADB and Fastboot are Android-side launched by device's bootloader. If you can't enter Fastboot mode then my guess is there is something is wrong with curently installed Android.
BTW: If you lock device's bootloader then bootloader attempts to load device's Stock ROM.
Click to expand...
Click to collapse
I see.
What can I do to try to fix this issue?
I finally managed to fix it through the Emergency Download Mode (EDL). It requires Xiaomi Authentication which I bypassed using this guide: https://www.droidwin.com/fix-mi-account-authorization-unbrick-xiaomi-edl-mode/
With that setup I flashed a stock rom using the MiFlash tool.