Hi Friends I Own Lava Iris 406Q,
Someone here gave me stock firmware of my device i used to flash by device with "c230wLAVA_fastboot_flash_all.bat" file provided by him in the firmware folder in a single click. But yesterday i wrongly clicked on"EraseAll.bat" command which have following instructions;-
@ECHO on
@ECHO Please switch to fastboot mode
@ECHO If the system started, run adb reboot-bootloader
adb reboot bootloader
fastboot erase modem
fastboot erase sbl1
fastboot erase sdi
fastboot erase aboot
fastboot erase rpm
fastboot erase boot
fastboot erase tz
fastboot erase system
fastboot erase cache
fastboot erase recovery
fastboot erase splash
fastboot erase usbmsc
fastboot erase userdata
fastboot erase misc
fastboot reboot
pause"Now my device isn't vibrating on pressing the power key, not showing anything its like in a switch off state. PC and adb are not recognizing it but windows recognize it as QHSUSH_BULK only, on using QFIL am unable to flash it with error message as "unable to switch it to Emergency Download Mode".
Is the repair possible to my device by these ordinary softwares like QPST, QFIL Or Any Other Softwares ???? Or am i missing some firmware components? Can Service centres repair my device?? How much it will cost?
If someone knows how to repair the device effectively, please respond.. Or just reply with whether my device is repairable or not.
Thanks
What phone do u have ??
bsaptarsi669 said:
What phone do u have ??
Click to expand...
Click to collapse
OP said "Lava Iris 406Q"
Lava Iris 406Q - Full phone specifications
www.gsmarena.com
Related
Hi all,
Since Sunday I try to solve the hard brick of my Moto G XT1032. I was on a rom GPE in 4.4.4 (EU) and by making the MAJ Lollipop during the sunday, the tel reboot on the logo Motorola and nothing more.
I tested severals tutos on XDA and many french websites, as:
Http: // forum.xda-developers.com / showthread.php? T=2633272
http: // forum.xda-developers.com/moto-g/help/mo to-g-hard-brick-lollipop-t2998124
And a lot of the others...but nothing!
Well, I said myself it doesn't matter because mototool repair the tel with no problems, as usual. But not, many errors when I try of downgrade in 4.4.2 or in 4.4.4 with it. I tried to flash (cache/ system / data / Dalvik) with CWM and TWRP with one tens of versions all in all and impossible to make no anything to put back. I tried to install many rom's, always the same.
I have errors as " remote failure ", impossible of mount the partitions system/cache, hab check failed and more more more, i don't remember the other's errors...
I cannot copy files (like a rom) via ADB to the tel in mode bootloader and I don't know what to do anymore of the whole...
If you have an idea, I am interested because there I think that except the SAV ... i'am in bull***t. :silly:
Thanks to all of your help and good week!
(sorry for my poor english)
Try manually flashing a stock 4.4.4 ROM , not a 4.4.2 ROM, for your phone. You may not be able to flash motoboot if the bootloader on your phone is newer than the bootloader you are trying to flash.
audit13 said:
Try manually flashing a stock 4.4.4 ROM , not a 4.4.2 ROM, for your phone. You may not be able to flash motoboot if the bootloader on your phone is newer than the bootloader you are trying to flash.
Click to expand...
Click to collapse
I try but the problem it's adb, because it's impossible to synchronize my phone with it.
When i try "adb reboot-bootloader" in a shell, i have the error "device not found".
And it's impossible to continue the tutorial :
Code:
mfastboot flash partition gpt.bin
mfastboot flash motoboot motoboot.img
mfastboot flash logo logo.bin
mfastboot flash boot boot.img
mfastboot flash recovery recovery.img
mfastboot flash system system.img_sparsechunk.0
mfastboot flash system system.img_sparsechunk.1
mfastboot flash system system.img_sparsechunk.2
mfastboot flash system system.img_sparsechunk.3
mfastboot flash modem NON-HLOS.bin
mfastboot erase modemst1
mfastboot erase modemst2
mfastboot flash fsg fsg.mbn
mfastboot erase cache
mfastboot erase userdata
mfastboot reboot
What is the solution for this?
adb reboot bootloader works if your phone is booted and you have debugging enabled.
ADB commands don't work when the phone is in fastboot mode.
Put your phone into fastboot mode, connect it to your computer, type in "fastboot devices" and your's phone serial # should appear on screen.
audit13 said:
adb reboot bootloader works if your phone is booted and you have debugging enabled.
ADB commands don't work when the phone is in fastboot mode.
Put your phone into fastboot mode, connect it to your computer, type in "fastboot devices" and your's phone serial # should appear on screen.
Click to expand...
Click to collapse
OK. I have a phone serial who appear on screen (with the command "fastboot devices"), but with the command "adb devices", i have no serial, so no devices attached...
EDIT : Into TWRP Recovery, i have the adb serial too
ok, now it's good I the phone turn on a retail rom 4.4.4.
For all those who have experienced the problem (a GPE 4.4.2 update to 4.4.4 and 5.0.1), the procedure is "simple".
Install adb+fastboot and copy the rom into the folder.
Fisrt, put your phone into bootloader mode and check the command 'fastboot devices"; you must have a serial into the shell. Boot on the TWRP recovery (2.7.1.1) and type the command into the shell "adb devices"; again, you must have a serial. If it's OK, format cache/system/data/dalvik and reboot the phone into the bootloader.
In my case, i use the rom RETAIL-FR_4.4.4 OTA.
Code:
fastboot flash partition gpt.bin
fastboot flash modem NON-HLOS.bin
fastboot flash fsg fsg.mbn
fastboot erase modemst1
fastboot erase modemst2
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot erase cache
fastboot erase userdata
fastboot reboot
IF this does not work , it is still possible to achieve a different manipulation .
Take CWM recovery (Philz Touch for example) and try to push a rom with adb.
@+
You can't use adb commands when the phone is in fastboot mode. THis is why adb devices returns nothing.
Glad you got it working.
Hi, this is my first time making a post, ok here's the thing, a couple of days ago my phone run out of battery, when i come back to charge the phone, this just get stuck in the Motorola logo and don´t turn on, i never make nothing like root or flashing roms, the phone os was all stock Android 5.1; so i look in the internet for possible cause and i find that it was a bootloop, i try to get in to the fastboot flash mode to make a reset with the factory option but just get directly to the motorola logo and dont do nothing, so a try with the recovery option and gets in to the android system recovery <3e> and try the wipe data/factory reset but doesn´t work. I try even via computer using the minimal adb and fastboot to erase the cache and the userdata with the commands and doesn't work, still appearing the motorola logo. so i found that i have to install the original rom again but first ill have to unlock the bootloader for my device, so i did it, i unlock the bootloader and now appear <Device is UNLOCKED. Status Code: 3> and now appear the poster WARNING BOOTLOADER UNLOCKED instead of the motorola logo; then i search for the stock rom for my device and i find this one XT1040_PEREGRINE_RETBR_5.1_LPB23.13-8_cid12_CFC.xml.zip (i know that my device is peregrine because i remember saw it before in the settings but not remeber the hole name), so i make the installation with adb tools like the post say and make this commands:
fastboot flash partition gpt.bin
fastboot flash motoboot motoboot.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot reboot
when its over i press fastboot reboot, but then appears again the WARNING BOOTLOADER UNLOCKED poster, i try to make it again, bus still appearing, i try more than 10 times, but still appearing.
sorry if the post is too large but i try to explain everything so you guys can help me because im desesperate with this, thanks.
HanSolo97 said:
Hi, this is my first time making a post, ok here's the thing, a couple of days ago my phone run out of battery, when i come back to charge the phone, this just get stuck in the Motorola logo and don´t turn on, i never make nothing like root or flashing roms, the phone os was all stock Android 5.1; so i look in the internet for possible cause and i find that it was a bootloop, i try to get in to the fastboot flash mode to make a reset with the factory option but just get directly to the motorola logo and dont do nothing, so a try with the recovery option and gets in to the android system recovery <3e> and try the wipe data/factory reset but doesn´t work. I try even via computer using the minimal adb and fastboot to erase the cache and the userdata with the commands and doesn't work, still appearing the motorola logo. so i found that i have to install the original rom again but first ill have to unlock the bootloader for my device, so i did it, i unlock the bootloader and now appear <Device is UNLOCKED. Status Code: 3> and now appear the poster WARNING BOOTLOADER UNLOCKED instead of the motorola logo; then i search for the stock rom for my device and i find this one XT1040_PEREGRINE_RETBR_5.1_LPB23.13-8_cid12_CFC.xml.zip (i know that my device is peregrine because i remember saw it before in the settings but not remeber the hole name), so i make the installation with adb tools like the post say and make this commands:
fastboot flash partition gpt.bin
fastboot flash motoboot motoboot.img
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot reboot
when its over i press fastboot reboot, but then appears again the WARNING BOOTLOADER UNLOCKED poster, i try to make it again, bus still appearing, i try more than 10 times, but still appearing.
sorry if the post is too large but i try to explain everything so you guys can help me because im desesperate with this, thanks.
Click to expand...
Click to collapse
If your goal is to re-lock the bootloader: try the command: fastboot oem lock
However, I don't see that solving your problem and may compromise your ability to restore to stock. Instead check this link and follow the install directions EXACTLY:
http://forum.xda-developers.com/moto-g/4g-development/rom-stock-motorola-4g-lollipop-rom-t3142816
eg. for Canada choose: XT1040 (Note: for Rogers/Fido - confirmed)
Retail Canada 5.1 ROM (Untouched) (531mb) [Download]
i.e., you want the untouched version for your specific region.
Good luck. S
Recently I rooted my phone and flash the resurrection remix naught in moto g3 xt1550....
For some reason I start to flash firmware ROM .....but it is not flashing.... Shows " preflash validation failed " and on system image " invalid image" .......... I tried many times but it didn't flash......when I skip the partition gpt file then every image file start flashing and phone start..,..
But their is no network......
After that whenever I switch off or reboot or go to recovery rather than that it start boot loader....
Then I flashed the resurrection remix again..... When I press reboot after flashing then it goes to boot loader......
At boot loader I press power on then it start booting and there is no network in this ROM too......
What can I do now ...... Please help.........
To clear the Fastboot mode, in fastboot enter "fastboot oem fb_mode_clear" and after that it should start the OS without going into fastboot each time.
The fact this is happening leads me to believe your other problem is related... meaning you didn't flash the stock images properly. If you have no network then you need to reflash the radio stack and boot.img file, they must match and you have to erase the modemstX partitions for the radios to work properly.
yes U will get the error of "preflash validation failed" cause of the security update which motorola released for the month of October, January and recent April.... Do one thing again flash the appropriate stock rom according to ur mobile But skip these two steps/Files >>> 1) fastboot flash partition gpt.bin and 2) fastboot flash bootloader bootloader.img and enter the remaining command/or follow the whole procedure but skip these two file mentioned above U will succed:fingers-crossed::good:
For ur simplicity im providing u commands and plz CHECK UR SPARSECHUNK Files it varies according to mobile I have 7 thats y 7 sparsechunk files DO CHECK URs ok>>>>
fastboot oem fb_mode_set
fastboot flash logo logo.bin
fastboot flash boot boot.img
fastboot flash recovery recovery.img
fastboot flash system system.img_sparsechunk.0
fastboot flash system system.img_sparsechunk.1
fastboot flash system system.img_sparsechunk.2
fastboot flash system system.img_sparsechunk.3
fastboot flash system system.img_sparsechunk.4
fastboot flash system system.img_sparsechunk.5
fastboot flash system system.img_sparsechunk.6
fastboot flash system system.img_sparsechunk.7
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize
fastboot erase clogo
fastboot oem fb_mode_clear
fastboot reboot
Do it ur own risk Im not responsible for any damage :laugh:
everything went well except my network .........i checked in about phone < status < imei no is " 0 ".......how to restore that...........i think thats why the network isn't showing.......................
acejavelin said:
To clear the Fastboot mode, in fastboot enter "fastboot oem fb_mode_clear" and after that it should start the OS without going into fastboot each time.
The fact this is happening leads me to believe your other problem is related... meaning you didn't flash the stock images properly. If you have no network then you need to reflash the radio stack and boot.img file, they must match and you have to erase the modemstX partitions for the radios to work properly.
Click to expand...
Click to collapse
where I find radio stack...... I don't know........and I didn't flash the stock images correctly because I have to skip the partition gpt and bootloader......
give me something else to solve it......
btw thanks sir......:good:
heisenberg1546 said:
where I find radio stack...... I don't know........and I didn't flash the stock images correctly because I have to skip the partition gpt and bootloader......
give me something else to solve it......
btw thanks sir......:good:
Click to expand...
Click to collapse
The "radio stack" is the relevant radio portions of the firmware image...
Code:
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
It is not uncommon that they don't take the first time, repeat it and the boot.img command. Verify EVERY command returns an OKAY response, if not, repeat it.
And do not copy and paste the commands all at once, type them out and look at the response, or at least copy and paste each command individually.
acejavelin said:
The "radio stack" is the relevant radio portions of the firmware image...
Code:
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
It is not uncommon that they don't take the first time, repeat it and the boot.img command. Verify EVERY command returns an OKAY response, if not, repeat it.
And do not copy and paste the commands all at once, type them out and look at the response, or at least copy and paste each command individually.
Click to expand...
Click to collapse
isn't working sir........
I did without copy paste.........
boot img command gives preflash validation failed....
heisenberg1546 said:
It is not uncommon that they don't take the first time, repeat it and the boot.img command. Verify EVERY command returns an OKAY response, if not, repeat it.
And do not copy and paste the commands all at once, type them out and look at the response, or at least copy and paste each command individually.
isn't working sir........
I did without copy paste.........
boot img command gives preflash validation failed....
Click to expand...
Click to collapse
You didn't do the boot.img... but Might want to look at the IMEI 0 recovery thread... I don't have any more ideas.
acejavelin said:
You didn't do the boot.img... but Might want to look at the IMEI 0 recovery thread... I don't have any more ideas.
Click to expand...
Click to collapse
After those commands ...... I flash again all img's including the boot.img......
How to restore the imei file ..... Like in mediatek device ,,, we can write by sn tools .....
heisenberg1546 said:
After those commands ...... I flash again all img's including the boot.img......
How to restore the imei file ..... Like in mediatek device ,,, we can write by sn tools .....
Click to expand...
Click to collapse
I don't know... There is a thread here specifically about it, you will have to look there.
I want to keep the custom rom (RR-O-v6.0.0-20180511-ospreyl) with all networks
acejavelin said:
To clear the Fastboot mode, in fastboot enter "fastboot oem fb_mode_clear" and after that it should start the OS without going into fastboot each time.
The fact this is happening leads me to believe your other problem is related... meaning you didn't flash the stock images properly. If you have no network then you need to reflash the radio stack and boot.img file, they must match and you have to erase the modemstX partitions for the radios to work properly.
Click to expand...
Click to collapse
Hey, I have installed RR-O-v6.0.0-20180511-osprey on Moto G(3rd Generation), and now the error is: "No sim Detected ", IMEI number is fine. I want to flash radio firmware in this custom Rom. Will flashing radio stack of stock rom 6.0.1 (Moto G3 x1550) work?
adb reboot bootloader
fastboot flash modem NON-HLOS.bin (That must of Moto G3?)
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot flash boot boot.img (Is it to be of RR or of Moto?)
fastboot reboot
Is there any other option or solution then please mention.
You need to flash stock firmware first then your network problem solved then you can install custom roms?
Good Luck!
Hello friends ... My device XT 1550 is Booting into The Bootloader mode when i switch on/reboot my device. This started Happen when i decided to return back to Stock 6.0.1 . Before Installing the custom rom i was April Security Update on Stock MM .
Everything was going perfectly file While Flashing the stock but when I started typing these commands fastboot flash system system.img_sparsechunk.7
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize ... Error Arises ... I got affraid ... I flashed the custom Rom Again and after that every time i switch on my device it first boot into Bootloader mode and then i press the power button it boots normally ...
And one hour before i connected my device to pc when it was Switched on it is detected by pc but when im on bootloader pc does not detect the device ie Status Show : Battery is OK instead of charging ... adb also show waitng for device help me guyzzz :crying:
Use this -
Code:
fastboot oem fb_mode_clear
BTW, that looks like a modded USB cable, can you use the oem one to ensure that the cable is not the problem? It should charge nonetheless.
Broadcasted from Zeta Reticuli
i have try the different cable ... but message shown in bootloader : Please Connect USB cable ... What to do ?
abhi8939 said:
Hello friends ... My device XT 1550 is Booting into The Bootloader mode when i switch on/reboot my device. This started Happen when i decided to return back to Stock 6.0.1 . Before Installing the custom rom i was April Security Update on Stock MM .
Everything was going perfectly file While Flashing the stock but when I started typing these commands fastboot flash system system.img_sparsechunk.7
fastboot flash modem NON-HLOS.bin
fastboot erase modemst1
fastboot erase modemst2
fastboot flash fsg fsg.mbn
fastboot erase cache
fastboot erase userdata
fastboot erase customize ... Error Arises ... I got affraid ... I flashed the custom Rom Again and after that every time i switch on my device it first boot into Bootloader mode and then i press the power button it boots normally ...
And one hour before i connected my device to pc when it was Switched on it is detected by pc but when im on bootloader pc does not detect the device ie Status Show : Battery is OK instead of charging ... adb also show waitng for device help me guyzzz :crying:
Click to expand...
Click to collapse
Bro type all the commands for stock firmware
Search xda for stock firmware flashing of osprey xt1550
And before that stock flashing
Please type
Fastboot flash bootloader bootloader.img
Then type fastboot reboot-bootloader
Then type all the stock flashing instructions except that
Bootloader flashing one
Hope it helps an about adb adb wont detect adb works only when your device is booted and also usb debuging is on from settings
Thank You All for Ur Kind Response .... But The problem Has Been Solved ... MotoRola minimal adb driver were not installed bcz my laptop got corrupted previously and all motorola minimal driver / adb were not installed ... So i connected my device to pc and install the software through web ... yepiee ... I successfully reverted back to stock ...
I wanted to install custom recovery system on my phone.
So I tried fastboot with recovery image
what I did is this
1. Download recovery image
2. fastboot oem unlock
3. fastboot flash recovery recovery.img
then again it seems I got an error
the error was
Your device is corrupt. It can't be trusted and may not work properly
so I tried to reinstall OS
the step was this
1. fastboot erase boot
fastboot erase cache
fastboot erase recovery
fastboot erase system
fastboot erase userdata
fastboot oem unlock
fastboot flash bootloader ~(img file download it from google)
but suddenly it doesn't work anymore
doesn't work any button....
what should I do now..