[HELP]Water got in the phone - Moto G 2015 Q&A, Help & Troubleshooting

So, it's me again.. As the title says, water somehow got in the phone. I can see some humidity on both cameras. I noticed this problem when I tried to make a call and the device couldn't detect the sim card. So, I opened the back only to find water in the SIM slot. The SIM is working fine now as i managed to dry it out but now I have two more problems.. A) For whatever reason the devices overheats by itself way too aggressively and B) the touch screen is really messed up..
Safe mode seems to ease the touchscreen issue a bit but the phone is still useless..
And yes, i have used rice to dry it..
It's fully stock btw except the unlocked bootloader..
If anyone knows what to do I will be really REALLY glad as I dont have a backup device right now..
Thanks in advance.

mike.... said:
So, it's me again.. As the title says, water somehow got in the phone. I can see some humidity on both cameras. I noticed this problem when I tried to make a call and the device couldn't detect the sim card. So, I opened the back only to find water in the SIM slot. The SIM is working fine now as i managed to dry it out but now I have two more problems.. A) For whatever reason the devices overheats by itself way too aggressively and B) the touch screen is really messed up..
Safe mode seems to ease the touchscreen issue a bit but the phone is still useless..
And yes, i have used rice to dry it..
It's fully stock btw except the unlocked bootloader..
If anyone knows what to do I will be really REALLY glad as I dont have a backup device right now..
Thanks in advance.
Click to expand...
Click to collapse
Is the water visible under the LCD? If not then you might be able to save it. If water got into the LCD backlight, like my previous phone, the damage would be irreversible.
Your best bet would be to take it to a technician and disassemble the phone. Maybe try to get warranty claim if still applicable. Overheating means the motherboard is shorted and the battery needs to be disconnected as soon as possible. Also, disassembly is recommended to clean up any water residue to prevent further corrosion.
Now, may I ask, how did the water got in there? Did the gasket fail or you've made some mistake like not putting on the back cover securely?

The problem was the plastic covering the sim and sd slots. As soon as pulled out the cover that plastic fell down on the floor like it was never glued whereas the other plastic for the second sim was just fine. I will get a technician to fix it in the next few days but until then its staying in rice 24/7. BTW the touch screen does have some problems and it keeps on pressing stuff by it self, although i can fix it for a few seconds by placing my hand all over the screen when active and then closing the screen. When I open it back up the problems are gone for about 10 seconds. Also the is a wierd mark on the bottom of the screen that seems like water but it doesnt affect visibility that much.

Quick update: So, water seems to be in there after all those days as the screen gets worse every day that passes. The wierd thing is that I downgraded to lollipop because I thought that the 5.0 display drivers might be better for such a screen and.. Well the screen doesnt respond at all to touches.. Tech support will see the phone today or tomorrow but I dont think its worth to repair. :/

Best way to "dry" the pone is to turn it off, remove the battery if possible, and leave the phone in a bowl with RICE (yes rice) in it, fully covering.
Rice will suck up all the humidity close.

Related

Possibly water damaged Captivate half-working

I may have possibly water damaged my Captivate last night. It was in my pocket when water spilled on my lap, and I didn't immediately take it out. Very stupid of me. The USB port was open so I'm thinking liquid may have gotten into there... Also, there were water beads on the inside of the camera lens.
My recourse was to take it apart and try to let it dry out. Initially it wouldn't do anything upon being plugged in to the charger, so naturally I thought it was bricked. I've let it sit all day on a dry window sill next to the radiator. After putting the battery back in and plugging it in a little bit ago, the phone surprisingly booted up. Here's where I'm at now:
The phone boots normally, however if I plug it in to the charger I get an error stating Battery Temperature too high or something, so charging is paused. Does anybody know what this indicates?
Secondly, after being on for a minute or so, the screen gets screwy. Dark transparent overlays start flashing over everything and it gets unresponsive... I haven't left it on like this long b/c I was afraid something worse would happen - I usually rip the battery out of the back to shut it off.
My phones currently pulled apart and drying in the window sill. Whatever water got on/in it is not visibly there, however I understand some parts might still be wet.
Any advice? Also, I believe the water indicator on the battery and near the pins where the battery dock in the phone are both fine. They're white squares and haven't changed color. Any chance there are other indicators?
The phone isn't insured and I bought it back in August. Would warranty possibly cover this or will they know about the water damage?
jmusso said:
I may have possibly water damaged my Captivate last night. It was in my pocket when water spilled on my lap, and I didn't immediately take it out. Very stupid of me. The USB port was open so I'm thinking liquid may have gotten into there... Also, there were water beads on the inside of the camera lens.
My recourse was to take it apart and try to let it dry out. Initially it wouldn't do anything upon being plugged in to the charger, so naturally I thought it was bricked. I've let it sit all day on a dry window sill next to the radiator. After putting the battery back in and plugging it in a little bit ago, the phone surprisingly booted up. Here's where I'm at now:
The phone boots normally, however if I plug it in to the charger I get an error stating Battery Temperature too high or something, so charging is paused. Does anybody know what this indicates?
Secondly, after being on for a minute or so, the screen gets screwy. Dark transparent overlays start flashing over everything and it gets unresponsive... I haven't left it on like this long b/c I was afraid something worse would happen - I usually rip the battery out of the back to shut it off.
My phones currently pulled apart and drying in the window sill. Whatever water got on/in it is not visibly there, however I understand some parts might still be wet.
Any advice? Also, I believe the water indicator on the battery and near the pins where the battery dock in the phone are both fine. They're white squares and haven't changed color. Any chance there are other indicators?
The phone isn't insured and I bought it back in August. Would warranty possibly cover this or will they know about the water damage?
Click to expand...
Click to collapse
well you want to put in rice, so that the moisture is gone
rice it for sure. but warranty WILL not cover it UNLESS the tabs on the battery and phone are white (It might not have gotten wet if it was in your pocket)
if they are still white, or if your phone is white and battery red (then buy another battery) and get to the store and tell them you don't know what is wrong with it. The only indication that it is water damaged is if it is red and those tags are notoriously faulty so you could always argue your way through it if you have an account in good standing.
best of luck.
I know someone who "claimed' that insurance was supposed to be added to the phone when he got it and noticed that the person didn't do it properly (the guy was new so it helped his cause) and the manager of the cor store told him that they'd do a courtesy replacement and charged him the 125$ for a new device.
you could go that route should you need too...
I don't have access to rice at the moment... Would it do any good even if I absolutely can see no water anywhere in/on the phone?
Am I doing my phone any harm/potential harm by trying to turn it on every once in a while, or should I just let it be for a few days?
Take the phone apart and focus the strongest fan you have on it over night. It's probably best to not turn it on for awhile. Maybe if you focus a blow drier on it for perhaps several hours, air will find flow through the small openings within the case.
You may not be able to dry some parts of it unless you do a complete dismantle, but that may require special tools
Consider shipping it to get repaired only as a last resort, as I've read some bad reports about that.
Rice or some other dessicant is the way to go - it will pull moisture out. Also, turning it on (even putting the battery in) is bad - you are powering circuits and possibly creating shorts where water is present. You may have already done permanent damage.
If you get electronics wet, the best course of action is to remove the battery and put it in a bag of rice for a few days.
Now that You have the phone apart get an alcohol pad and gentley scrub the main board. Sometimes when liquid touches the main board you will get a white looking residue. If you see anything like that simply wipe it off. I dropped my phone into a trash can at a very popular teriyaki restaurant here in Las Vegas my phone was submerged into a deep bath of teriyaki sauce. I quickly pulled the phone from the can and wiped it down vigorously. I was excited to see that it was initially working unfortunately this was not the case by the time I got home. The phone would not turn on for a whole week, until I decided that I was going to open her up. I found a tutorial on line describing a complete break down of the captivate. Upon opening it I found I was able to see exactly where the teriyaki had interacted with the electronics due to the remnants of an oxidized white film that was present on various parts of the main board. I grabbed a alcohol pad out of my first aid kit and began wiping it down to remove all of the white stuff,put the phone back together and to my surprise it turned on. Hope this helps!
Thanks for the info guys.
How would I go about getting to the "main board"? Taking out the battery and looking inside it only reveals where the battery connects, where the SD card and sim cards can go... I'm assuming if I remove the little screws around that fixture I can get to the "main board"?
I think I can see some minor corrosion around where the sim card connects, but I think I *should* be able to clean that with some alcohol.
The phone seems to be working fine (I've yet to put my SIM back in it, though, so no idea if the corrosion around there is affecting it at all). I just booted it up and was able to get on the web (wifi), run apps, everything just fine. Didn't get the flashy screens I mentioned earlier. However, if I plug in the USB charger, it still gives me the temperature error. I didn't keep it plugged in, however it did make me realize something:
The errors I was getting before, where the screen went all wacky, only happened if the phone was plugged in to the wall. Is it possible my battery is busted, or do you think the USB charger is busted? Remember that port was open when it happened.
Any thoughts? New battery? Or do you think I won't be able to charge the phone via USB charger any more?
jmusso said:
I don't have access to rice at the moment... Would it do any good even if I absolutely can see no water anywhere in/on the phone?
Am I doing my phone any harm/potential harm by trying to turn it on every once in a while, or should I just let it be for a few days?
Click to expand...
Click to collapse
yes you are, because if there is water or moisture internal, it can short circuit, also rice will help dry up the phone completely
jmusso said:
Thanks for the info guys.
How would I go about getting to the "main board"? Taking out the battery and looking inside it only reveals where the battery connects, where the SD card and sim cards can go... I'm assuming if I remove the little screws around that fixture I can get to the "main board"?
I think I can see some minor corrosion around where the sim card connects, but I think I *should* be able to clean that with some alcohol.
The phone seems to be working fine (I've yet to put my SIM back in it, though, so no idea if the corrosion around there is affecting it at all). I just booted it up and was able to get on the web (wifi), run apps, everything just fine. Didn't get the flashy screens I mentioned earlier. However, if I plug in the USB charger, it still gives me the temperature error. I didn't keep it plugged in, however it did make me realize something:
The errors I was getting before, where the screen went all wacky, only happened if the phone was plugged in to the wall. Is it possible my battery is busted, or do you think the USB charger is busted? Remember that port was open when it happened.
Any thoughts? New battery? Or do you think I won't be able to charge the phone via USB charger any more?
Click to expand...
Click to collapse
If you've never taken apart a smart phone before, and reading your first question, I'm going to assume that's the case, then I strongly advise you not attempt it unless you are willing to either A) buy a replacement after you break it or B) invest time/money into repairing mistakes you've made. This phone is not as difficult to disassemble as some, but I wouldn't want to break that $150 amoled screen.
No, removing the screws will not simply get you to the mainboard. It's more complicated and nuanced than that.
I'm a new user so I can't post the link but if you google Tech Republic Captivate tear down [/B]there is a website that will show you step by step how take the phone apart. There are two screws under the clip you pull down to take the back cover off. Be careful when pulling it back to expose the screws. I tugged on it pretty hard with no problems, but I imagine it could be broken if you pull too hard. Good Luck! It's actually really easy to take apart and the various ribbon connectors on the main board are really easy to unplug and plug back in after cleaning it.
So what do you guys think I should do if I'm still getting the battery error with the thermometer and yellow caution sign? Buy a new battery? Or do you think its the USB jack? Has anybody seen this before - the battery was working fine as long as it was not charging.
I'm trying to decide between a) buying a new battery, or b) buying a wall-mounted battery charger since the USB won't charge the phone.
Anybody have any experience?
Meguro2006 said:
I'm a new user so I can't post the link but if you google Tech Republic Captivate tear down [/B]there is a website that will show you step by step how take the phone apart. There are two screws under the clip you pull down to take the back cover off. Be careful when pulling it back to expose the screws. I tugged on it pretty hard with no problems, but I imagine it could be broken if you pull too hard. Good Luck! It's actually really easy to take apart and the various ribbon connectors on the main board are really easy to unplug and plug back in after cleaning it.
Click to expand...
Click to collapse
I think you need to be careful about who you encourage to dissect their device. This guy asked how to get to the mainboard. Clearly, he hasn't opened a smart phone before. Telling him it's "actually really easy" is disingenuous at best. Performing smart phone repairs properly requires experience. I'm certainly not suggesting that noobs not try to fix their phones, only that they are made fully aware of the risks.
My Captivate was fully submerged in dirty water. I followed some instructions online and it's been working fine for over a month now. If your water-detection stickers are already red anyway, and rice isn't working, I recommend it:
1) Remove battery, SIM card, SD card
2) Submerge in a bowl of distilled water and gently agitate. This helps clean the insides. Distilled water (not spring water) does not conduct electricity.
3) Next, submerge in a bowl of high-quality rubbing alcohol (~95% pure) and gently agitate. Rubbing alcohol displaces water, removes corrosion, and evaporates quickly. (It's also flammable, so have good ventilation and no open flames nearby)
4) Leave it out to dry for two days or until it no longer smells of alcohol.
BTW I wouldn't dry it too close to a radiator, the heat may damage it.
jatkins09 said:
If you've never taken apart a smart phone before, and reading your first question, I'm going to assume that's the case, then I strongly advise you not attempt it unless you are willing to either A) buy a replacement after you break it or B) invest time/money into repairing mistakes you've made. This phone is not as difficult to disassemble as some, but I wouldn't want to break that $150 amoled screen.
No, removing the screws will not simply get you to the mainboard. It's more complicated and nuanced than that.
Click to expand...
Click to collapse
Not really. Once the screws are removed..including the two hidden by the battery cover lock slider...you can carefully pry the cover apart using your fingernail to get to the the internals. I have done it several times and am no expert by any means. Just don't yank like you are opening a present on Christmas morning.
Although I am mystified by the op stating they have no access to rice?! That should always be the second thing one does after a moisture incident...right after pulling the battery and sim. I guess in this case a trip to the store with a couple bucks may have pushed that to step three though..
sent from my captivate disguised as an i9000 running cyanogen

[Q] Got my phone wet. Everything still works but charging is unreliable

Hey everyone,
I wish I wasn't here under these circumstances, but yesterday my phone got drenched by the faucet when I accidentally dropped it in the sink. I turned it off right away and tried to dry it by blowing out all the holes/buttons/etc. with canned air. then (maybe stupidly) I turned the phone back on and used it the rest of the day, not really noticing that it wasn't charging when I plugged it in until later when the battery got very low and I plugged it in again and noticed that the charging symbol didn't appear.
Ultimately, what I found DID work, (at least temporarily, sometimes it still stops charging) was turning the phone off, then plugging it in, then turning it back on . When I did this, usb (and wireless) charging work, as well as the USB connection for getting files off the phone on my computer.
It's a bit odd that this is what worked, but so far, it seems to. I'm just not quite sure if there's anything else I can do other than maybe send the phone to LG for repair, or find a local shop that might be cheaper...
Just looking for any suggestions or information anyone may have to help me fix this. thanks in advance!
shorty6049 said:
Hey everyone,
I wish I wasn't here under these circumstances, but yesterday my phone got drenched by the faucet when I accidentally dropped it in the sink. I turned it off right away and tried to dry it by blowing out all the holes/buttons/etc. with canned air. then (maybe stupidly) I turned the phone back on and used it the rest of the day, not really noticing that it wasn't charging when I plugged it in until later when the battery got very low and I plugged it in again and noticed that the charging symbol didn't appear.
Ultimately, what I found DID work, (at least temporarily, sometimes it still stops charging) was turning the phone off, then plugging it in, then turning it back on . When I did this, usb (and wireless) charging work, as well as the USB connection for getting files off the phone on my computer.
It's a bit odd that this is what worked, but so far, it seems to. I'm just not quite sure if there's anything else I can do other than maybe send the phone to LG for repair, or find a local shop that might be cheaper...
Just looking for any suggestions or information anyone may have to help me fix this. thanks in advance!
Click to expand...
Click to collapse
You should have not used the phone but put it turned off in a bowl of uncooked rice for a few days. Optional also removed the back and the battery if possible. You will have corrossion now and maybe worse electrical damage.
gee2012 said:
You should have not used the phone but put it turned off in a bowl of uncooked rice for a few days. Optional also removed the back and the battery if possible. You will have corrossion now and maybe worse electrical damage.
Click to expand...
Click to collapse
Yeah, I recognize that it was a bad idea... but there's not much I can do about that now. I'm just trying to figure out what my best course of action going forward is.
shorty6049 said:
Yeah, I recognize that it was a bad idea... but there's not much I can do about that now. I'm just trying to figure out what my best course of action going forward is.
Click to expand...
Click to collapse
Try to remove the back and battery and place it in a bowl of uncooked rice asap for 2-3 days, this will limit the damage. Your warranty will also be voided i`am afraid as the moisture indicators are colored now.
gee2012 said:
Try to remove the back and battery and place it in a bowl of uncooked rice asap for 2-3 days, this will limit the damage. Your warranty will also be voided i`am afraid as the moisture indicators are colored now.
Click to expand...
Click to collapse
what do you think the chances of the moisture indicators NOT being colored would be?
I had the phone inside a bumper case which covers the sides of the phone and the back. Some water got inside the case, but maybe not enough to wet the indicators.. I'd hate to open the phone and then realize they weren't colored. I hate opening phones if possible, but that'd be the only way to know for sure , I guess...
I'm working on getting my hands on a back up phone to use currently , but I hate to see the condition of this one get worse... (my nexus 4 that I was going to use as a backup hasn't wanted to power on in a couple months after I botched Rom flashing attempt and subsequent failure to accept a charge)
shorty6049 said:
what do you think the chances of the moisture indicators NOT being colored would be?
I had the phone inside a bumper case which covers the sides of the phone and the back. Some water got inside the case, but maybe not enough to wet the indicators.. I'd hate to open the phone and then realize they weren't colored. I hate opening phones if possible, but that'd be the only way to know for sure , I guess...
I'm working on getting my hands on a back up phone to use currently , but I hate to see the condition of this one get worse... (my nexus 4 that I was going to use as a backup hasn't wanted to power on in a couple months after I botched Rom flashing attempt and subsequent failure to accept a charge)
Click to expand...
Click to collapse
Water goes through the tiniest cracks and openings so i guess the indicators are colored. Only one sure way to find out and that is looking inside the phone. Look on YouTube for a Nexus 5 iFixit dissasembly video.
Opening up the phone doesn't really void the warranty. Breaking something while opening it does. You still had the headphone jack and the usb port open right? That means water got in and tripped the sensors. This is pretty much guaranteed. IMO, those sensors are too sensitive. Just using the phone in a humid place (bathroom while shower is running) trips them.
If everything works fine just try a wireless charger
Sent from my Nexus 5 using Tapatalk
The fact that your charging doesn't work reliably anymore probably means the moisture indicators would be coloured... I've had phones where the water didn't damage it at all and they still were
Sent from my Nexus 5 using Tapatalk

[Q] Water Damaged Nexus 5 Boot Loop Suggestions

Hi all,
First off I would like to thank anyone and everyone that reads this thread, it helps me out if you have any information that could help me out here.
About a week or so ago my girlfriend dropped her Nexus 5 in water, and removed it almost immediately then brought it to me. Sadly the damage was already done and the screen was black. I got the back off and got as much water out as I could shake gently, and the screen still had haptic feedback when I touched it, so I messaged it and it displayed the notification light. This led me to believe the battery was ok, so we left the back off and let it dry for a while, and over time the screen and sound came back. We placed the phone overnight in dry rice, and for the meantime we put her SIM in an old S2. The next morning there was obvious water damage on the screen but less than before, and everything seemed to be working fine, games ran, music played, messages came and went on Hangouts, and when we plugged it in to charge it worked like a charm, so we believed we had gotten lucky, put it back in the rice overnight again and the next day tried putting the SIM card back in the phone.
The Nexus at this point asked to restart and we obliged, but this is when the problem started. It would get to the Google boot screen, hang, then restart, over and over. I tried going into recovery and I could, but no further than that. I am not an expert so don't know what would cause this, but I am led to believe that the battery and everything else is all in working order otherwise it wouldn't have been working and charging while it was on. I wonder if maybe there is a separate part of the phone used for BIOS bootup and it got damaged? Any suggestions or ideas on how to fix the issue would be met with extreme gratitude. Thanks for reading all this.
TL;DR Phone was dropped in water, aired out and worked fine, restarted for SIM card and get stuck in endless boot loop.
QyuBurt said:
Hi all,
First off I would like to thank anyone and everyone that reads this thread, it helps me out if you have any information that could help me out here.
About a week or so ago my girlfriend dropped her Nexus 5 in water, and removed it almost immediately then brought it to me. Sadly the damage was already done and the screen was black. I got the back off and got as much water out as I could shake gently, and the screen still had haptic feedback when I touched it, so I messaged it and it displayed the notification light. This led me to believe the battery was ok, so we left the back off and let it dry for a while, and over time the screen and sound came back. We placed the phone overnight in dry rice, and for the meantime we put her SIM in an old S2. The next morning there was obvious water damage on the screen but less than before, and everything seemed to be working fine, games ran, music played, messages came and went on Hangouts, and when we plugged it in to charge it worked like a charm, so we believed we had gotten lucky, put it back in the rice overnight again and the next day tried putting the SIM card back in the phone.
The Nexus at this point asked to restart and we obliged, but this is when the problem started. It would get to the Google boot screen, hang, then restart, over and over. I tried going into recovery and I could, but no further than that. I am not an expert so don't know what would cause this, but I am led to believe that the battery and everything else is all in working order otherwise it wouldn't have been working and charging while it was on. I wonder if maybe there is a separate part of the phone used for BIOS bootup and it got damaged? Any suggestions or ideas on how to fix the issue would be met with extreme gratitude. Thanks for reading all this.
TL;DR Phone was dropped in water, aired out and worked fine, restarted for SIM card and get stuck in endless boot loop.
Click to expand...
Click to collapse
Take the device apart, remove the motherboard. Get some rubbing alcohol and a tooth brush.
Remove any shields that can be taken off to expose more components. Then start scrubbing!!! Continue until you get all of the green/white corrosion. If there are any black scorch marks on the connections, take a eraser and it will remove the burn mark, then continue to clean with alcohol. Also the flex cable connections would need to be cleaned also.
The next step is up to you, if you feel comfortable with it. Make sure all plastic and rubber pieces are off the motherboard. Then stick it in the oven on 400F for 30 min to reflow some of the solder that may have gotten damaged.
Put back together, you may have to factory reset if the software got corrupted.
It is still highly possible to recover the device.
Good luck!
oOflyeyesOo said:
Take the device apart, remove the motherboard. Get some rubbing alcohol and a tooth brush.
Remove any shields that can be taken off to expose more components. Then start scrubbing!!! Continue until you get all of the green/white corrosion. If there are any black scorch marks on the connections, take a eraser and it will remove the burn mark, then continue to clean with alcohol. Also the flex cable connections would need to be cleaned also.
The next step is up to you, if you feel comfortable with it. Make sure all plastic and rubber pieces are off the motherboard. Then stick it in the oven on 400F for 30 min to reflow some of the solder that may have gotten damaged.
Put back together, you may have to factory reset if the software got corrupted.
It is still highly possible to recover the device.
Good luck!
Click to expand...
Click to collapse
I wouldn't go so far as reflowing solder for a dry-out.
http://www.amazon.com/o/ASIN/B000BXOGNI?tag=adapas02-20
can be attained at your local auto supply, simply disassemble the boards and give them a once-over spray and wipe-down. Reassemble, and then troubleshoot the bootloop, which may require a full stock flash. Good luck!
wideasleep1 said:
I wouldn't go so far as reflowing solder for a dry-out.
http://www.amazon.com/o/ASIN/B000BXOGNI?tag=adapas02-20
can be attained at your local auto supply, simply disassemble the boards and give them a once-over spray and wipe-down. Reassemble, and then troubleshoot the bootloop, which may require a full stock flash. Good luck!
Click to expand...
Click to collapse
I am not reflowing to dry it, sometimes solder on the connections/components need to be reflowed when they got WD or the device will not function correctly.I have seen it more time that I can count.
oOflyeyesOo said:
I am not reflowing to dry it, sometimes solder on the connections/components need to be reflowed when they got WD or the device will not function correctly.I have seen it more time that I can count.
Click to expand...
Click to collapse
There wouldn't be solder damage when OP acted almost immediately to dry it out. A cleaning, further drying should be all that's needed. One should NEVER turn on electronics until fully disassembled, cleaned and dried in any event.
wideasleep1 said:
There wouldn't be solder damage when OP acted almost immediately to dry it out. A cleaning, further drying should be all that's needed. One should NEVER turn on electronics until fully disassembled, cleaned and dried in any event.
Click to expand...
Click to collapse
The second the device hits air corrosion starts to build. Rice does nothing, it pulls a little bit of the water from the charge port and headset jack, basically what drips out. There is possibility that there is still water inside the device. He needs to open it up to scrub it down with a tooth brush and alcohol at least.The connections may break in time even after cleaning, that is why I suggest a reflow.
oOflyeyesOo said:
The second the device hits air corrosion starts to build. Rice does nothing, it pulls a little bit of the water from the charge port and headset jack, basically what drips out. There is possibility that there is still water inside the device. He needs to open it up to scrub it down with a tooth brush and alcohol at least.The connections may break in time even after cleaning, that is why I suggest a reflow.
Click to expand...
Click to collapse
I don't disagree most of this up to the point of reflow, which should be an absolute, last-ditch exercise. If corrosion is a major concern, after cleaning with solvent, a Caig deoxit treatment would be my next advice, but I think reflow is best left to the experienced.
wideasleep1 said:
I don't disagree most of this up to the point of reflow, which should be an absolute, last-ditch exercise. If corrosion is a major concern, after cleaning with solvent, a Caig deoxit treatment would be my next advice, but I think reflow is best left to the experienced.
Click to expand...
Click to collapse
Thanks to both of you for your advice on this. I will go and get some of the cleaning spray you suggested and give all the components a good clean, and will look for any scorch marks that may have occured when it was damaged. I would try flashing the OS as well but I'm not entirely sure how to do that when the phone has not been set up for USB Debugging. I attempted to flash it after unlocking the bootloader, but that didn't seem to work either. I will report back when I have performed the steps and let you know if there has been any progress.
Thanks =)
QyuBurt said:
Thanks to both of you for your advice on this. I will go and get some of the cleaning spray you suggested and give all the components a good clean, and will look for any scorch marks that may have occured when it was damaged. I would try flashing the OS as well but I'm not entirely sure how to do that when the phone has not been set up for USB Debugging. I attempted to flash it after unlocking the bootloader, but that didn't seem to work either. I will report back when I have performed the steps and let you know if there has been any progress.
Thanks =)
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2513701
And to the guy above, sorry if it seemed I was arguing. A few too many drinks at that point.

[Q] Water Damaged LG G2 Works But Won't Show Image On Screen

So like the title suggests, I have a water damaged LG G2 that won't fully work. A little back-story, I went swimming one day at the pool and while I was swimming I totally forgot my phone was still in my pocket. I was only in the water for a few minutes and realized my mistake so I quickly drove home and disassembled it. I immediately soaked it in rice for a few days but unfortunately its fried so I decided to do some tests to see if i could fix it myself. I played with it for a while, scrubbed off the corrosion, replaced the battery and the phone works now but the screen wont display an image. I put in another replacement screen but to no avail so I'm assuming it has something to do with the logic board although I'm not for sure. If anyone could shed some light on what might be the problem or help me with a solution it would be greatly appreciated :good:
thanks
irootbeer said:
So like the title suggests, I have a water damaged LG G2 that won't fully work. A little back-story, I went swimming one day at the pool and while I was swimming I totally forgot my phone was still in my pocket. I was only in the water for a few minutes and realized my mistake so I quickly drove home and disassembled it. I immediately soaked it in rice for a few days but unfortunately its fried so I decided to do some tests to see if i could fix it myself. I played with it for a while, scrubbed off the corrosion, replaced the battery and the phone works now but the screen wont display an image. I put in another replacement screen but to no avail so I'm assuming it has something to do with the logic board although I'm not for sure. If anyone could shed some light on what might be the problem or help me with a solution it would be greatly appreciated :good:
thanks
Click to expand...
Click to collapse
Well, you seem to have already done the things I would have suggested. If you've already dropped in a replacement glass/digitizer/LCD assembly and it still isn't working, then I got nothing. I'd send it in to someone to have it fixed or get a new phone. That said, I was actually replacing that assembly myself this weekend after being dumb/inebriated and having my phone fall out of my pocket, cracking the glass and digitizer. One thing I noticed that I didn't expect is that even if everything is completely assembled, if you take off the back cover and turn the phone on, the phone will boot up and respond to touch, but the screen will not turn on. Looking more closely at the back cover, there are a few contacts on there so apparently you have to have the cover on for the screen to work. You could double check to see if there might still be some corrosion on the back cover on those contacts. That's about all I got though.

Few drops of water

Hi All,
Last night few drops of water dropped on my one mini and it started getting stuck and asking me to send report.
It gets stuck from time and then I have to restart it. Also the phone restarts by itself.
There was not more than few drops of water but as I use a case, the water remained in the case for an hour lets say. The lens on the back camera was also blurred a bit but today its gone. What worries me is that the plastic bezzel has cracks ( known problem for the mini I think) and I assume some water might have went inside the phone.
Is it possible that this is causing the phone to freeze and restart and such things or not? It was working flawlesly up till last night.
I've just placed it in a bag of rice hoping to remove all water inside.
Really need your advise.
Thanks
raperot said:
Hi All,
Last night few drops of water dropped on my one mini and it started getting stuck and asking me to send report.
It gets stuck from time and then I have to restart it. Also the phone restarts by itself.
There was not more than few drops of water but as I use a case, the water remained in the case for an hour lets say. The lens on the back camera was also blurred a bit but today its gone. What worries me is that the plastic bezzel has cracks ( known problem for the mini I think) and I assume some water might have went inside the phone.
Is it possible that this is causing the phone to freeze and restart and such things or not? It was working flawlesly up till last night.
I've just placed it in a bag of rice hoping to remove all water inside.
Really need your advise.
Thanks[/QUOTE/]
Anyone?
Click to expand...
Click to collapse
raperot said:
raperot said:
Hi All,
Last night few drops of water dropped on my one mini and it started getting stuck and asking me to send report.
It gets stuck from time and then I have to restart it. Also the phone restarts by itself.
There was not more than few drops of water but as I use a case, the water remained in the case for an hour lets say. The lens on the back camera was also blurred a bit but today its gone. What worries me is that the plastic bezzel has cracks ( known problem for the mini I think) and I assume some water might have went inside the phone.
Is it possible that this is causing the phone to freeze and restart and such things or not? It was working flawlesly up till last night.
I've just placed it in a bag of rice hoping to remove all water inside.
Really need your advise.
Thanks
Click to expand...
Click to collapse
Anyone?
Click to expand...
Click to collapse
Can you please share some advice?
Is it possible that the phone gets stuck closes apps, asks me to send reports because of the humidity inside?
Sadly yes, it is possible to be producing errors due to the humidity.
It might be temporary ( stop once every single bit of humidity/water is out ) or permanent ( stay like that forever ).
Leave it dipped in rice for another 24 hours, and try again.
If it continues giving you errors, backup your data, and install a new ROM afresh ( clean install a ROM ) and see if it works ok.
htc_one_mini_m4 said:
Sadly yes, it is possible to be producing errors due to the humidity.
It might be temporary ( stop once every single bit of humidity/water is out ) or permanent ( stay like that forever ).
Leave it dipped in rice for another 24 hours, and try again.
If it continues giving you errors, backup your data, and install a new ROM afresh ( clean install a ROM ) and see if it works ok.
Click to expand...
Click to collapse
Thanks a lot for your advice.
I left it again for allmost 12 h in rice but its the same I'm afraid.
I'll give it a shot with installing a new/stock rom.
Damn, it was just few drops .... unbelieveable.
No success so far.
I've left it at repair shop but the guy is not able to instal any rom.
Its just stuck at HTC logo and doesnt want to boot up now.
The strange thing is that I can go into recovery, go up and down the menu no probelm, and it never shuts down and restarts when in recovery but it doesnt want to boot up.
Guy in the shop says that it perhaps has some corrosion and this causes the problem. Due to the plastic lines cracks he doesnt want to open the phone and try to clean it. He says if he tries to open the plastic frame will break totaly.
Any solution or I should just give up??? Really desperate here
I just finished repairing a one mini with cracks on every side. It was a pita but it can be done without damaging the frame. I had to into it 3 times for various reasons, and it did not damage the frame. I think the guy at the repair shop just doesn't want to bother with it, and I'd take it (and my money) elsewhere.
I managed to open it as well without damaging the frame. It comes of fairly easily. A nice tutorial here
http://www.youtube.com/watch?v=cXb3l47qicI
Now to the repaire shot for the guy to check if this one can be saved.

Categories

Resources