Database Info

Samsung galaxy S 4G can't back to stock

please help !! i have tried to update the kernel and my phone was bricked.
i have tried to back to stock, everything is fine until odin said PASS! then the phone dosen't start in recovery mode , but he says Samsung Virant and he stay like that !

mouadm said:
please help !! i have tried to update the kernel and my phone was bricked.
i have tried to back to stock, everything is fine until odin said PASS! then the phone dosen't start in recovery mode , but he says Samsung Virant and he stay like that !
Click to expand...
Click to collapse
What phone do you have exactly? This forum is for the Galaxy S 4G, not the Vibrant. Also, what did you try to flash with ODIN?

i have samsung galaxy S 4G , i tried to back to stock .

mouadm said:
i have samsung galaxy S 4G , i tried to back to stock .
Click to expand...
Click to collapse
Sounds like you tried to put a Vibrant ROM on it, though, which is why it goofed. Can you get it into download mode by:
Power off the phone
Plug in the USB cable to the phone and computer
Hold down the volume up & volume down keys at the same time
Press and release the power button
Press the volume up button to get into download mode
or
Power off the phone
Remove the battery
Plug in the USB cable to the phone and computer
Hold down the volume up & volume down keys at the same time
Insert the battery while holding those keys
Press the volume up button to get into download mode

yes i can get into download mode , can yuou give me the right stock

mouadm said:
yes i can get into download mode , can yuou give me the right stock
Click to expand...
Click to collapse
Yeah, give this one from Whitehawkx a shot if you want the original Froyo KD1 ROM. If you want the latest Gingerbread 2.3.6, use this one from RaverX3X.
Both are flashed via ODIN & both contain the proper boot loaders. Let me know if you need any help with that.

Thanks ,, with Froyo KD1 how can i add the "Modded 3e Recovery"

mouadm said:
Thanks ,, with Froyo KD1 how can i add the "Modded 3e Recovery"
Click to expand...
Click to collapse
No worries, I hope you get it going again. If you're wanting the CWM recovery for Froyo I would suggest krylon360's [RECOVERY]CWM FINAL for the SGS4G - FROYO ONLY.
Another way would be to flash a kernel that has it built in. I believe the Bali kernel has it built in. Check out the [REF]{BIBLE} Galaxy S 4G (12/25/11) <10:00pm cst>. It has a lot of information and links that can help you out.

i tried to flash it with odin he says FAIL! several times

You have to get the phone into download mode first. You can do that a few ways and here are a couple:
Power off the phone
Plug in the USB cable to the phone and computer
Hold down the volume up & volume down keys at the same time
Press and release the power button
Press the volume up button to get into download mode
or
Power off the phone
Remove the battery
Plug in the USB cable to the phone and computer
Hold down the volume up & volume down keys at the same time
Insert the battery while holding those keys
Press the volume up button to get into download mode
Once it's in download mode & ODIN sees it, you should be able to flash.
Note the download is a .rar file, which is an archive. You'll need to un-rar it (I think 7Zip does this and there are other un-rar utilites) then put the un-archived file in the PDA section of ODIN and it should work.

it's exactly what i do , >>> FAIL! he stop in MODEM step

mouadm said:
it's exactly what i do , >>> FAIL! he stop in MODEM step
Click to expand...
Click to collapse
Can you copy & paste the whole log here? It's possible it's a bad download, too. Maybe re-download the file and try again.

<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T959VUVKJ6-REV00-home-low-CL694130.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> Sbl.bin
<ID:0/007> cache.rfs
<ID:0/007> factoryfs.rfs
<ID:0/007> modem.bin
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Thanks for the log. Interesting. What version of ODIN are you using? I recommend 1.85 as I think it's the latest available. Also, re-download the file to make sure it's a good file.

Keep Odin open on the computer, keep the usb cable plugged into the computer
Pull out your battery and usb cable from the phone
Put the battery back in
Hold vol + and -, keep holding them.
Plug the usb cable into the phone.
Try flashing with Odin again once it detects your phone.

i downloaded odin 1.85 and i redownloaded the file but the same result .
when i try the stock (samsung vibrant) odin work , but he diden't boot in recovery mode , so it's blocked in the first screen ' samsung vibrant"

Pull out the battery on the phone and copy down everything it says on the white sticker and post it here.

he dosen't show anything

mouadm said:
he dosen't show anything
Click to expand...
Click to collapse
I think FB is trying to verify the model of the phone you have. Beneath the battery is a white sticker that should show you the model number and other information. Does the model number show SGH-T959V?

sorry i haven't understood you , yes the model is SGH-T959V ,
i think the problem is the file isn't the right one for my phone .

[Q] soft bricked tablet tab 2 p5113/pp5110? Firmware upgrade encountered an issue.

I have a samsung galaxy tab 2 10.1. It came to me as a pt 5113. When I rooted it and updated the software to 4.3 using cmworld nightly it changed to p5110.
I wanted to downgrade because I wasn't able to use a lot of things and felt limited. However, my tablet won't turn off until it runs out of battery and I'm trying to just return it to the way it was before I tried to downgrade but it's not letting me. So I think it might be bricked. I don't know if it's a soft brick or a hard brick... I'm just so lost. Can anyone help me find how to straighten everything out if it can or provide me with step by step instructions.
Is there a way where I can just start fresh and just turn my tablet back to the way it was when I first bought it?
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
I am now stuck on the "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again." However, Kies won't recognize my tablet cause it's rooted and stuff. So I can't do that.
I tried using these websites:
http://forum.xda-developers.com/show....php?t=2258628
http://www.infamousdevelopment.com/i...890#msg890)*
they are essentially the same. I'm on odin right now and it won't go further than
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUAMDL_M919TMBAMDL_M919UVUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
my screen won't go into download mode or recovery mode.
I believe it's soft bricked but everything I find won't work. What should I do?
I also tried plugging it in and out with the odin screen up because some people said it helped but that didn't help me.
I tried doing the adb command window but my computer doesn't show a list of devices indicating that my tablet isn't connected... but it is..
What should I do? Dang Nabbit! :crying:

You can force the tablet to power off by holding in the power button about 10 seconds. It will then cold boot after a few seconds if you do nothing.
As soon as it powers off, try going into recovery by pressing the power and volume down keys until the Samsung 10.1 logo appears. If that fails, force power off again and try going into download mode, pressing power and volume up keys. If you can get into the download mode, connect to your PC and try installing TWRP with Odin.
Just a reminder, volume down is next to the power switch. Also remember to unplug the power or you can't get into either download or recovery modes!
Installing TWRP Recovery:
I use TWRP, some good instructions are here You already have the drivers and Odin installed, so skip that part, and go to where he installs TWRP Recovery with Odin.
- Go to ODIN window and click PDA. Browse your PC for the TWRP Recovery .tar file and then load it into ODIN.
- Don’t change any default settings of ODIN. Press the START button when you’re ready for the installation process.
- After the install is complete you will notice that ODIN says PASS and the tablet restarts.
- Wait for the tablet to reboot and then it will load the Android OS. This means that the installation was successful and you can disconnect the Galaxy Tab 2 10.1 from your PC.
Click to expand...
Click to collapse
See if that gets you going. Then you can try flashing a stock ROM.
Or try flashing this ROM It is a rooted version of stock 4.2.2 with busybox.
Be sure and wipe Data/Cache/Dalvik Cache as he instructs. This should get you back to a stock, rooted ROM.

No fix found so far
ron12 said:
You can force the tablet to power off by holding in the power button about 10 seconds. It will then cold boot after a few seconds if you do nothing.
As soon as it powers off, try going into recovery by pressing the power and volume down keys until the Samsung 10.1 logo appears. If that fails, force power off again and try going into download mode, pressing power and volume up keys. If you can get into the download mode, connect to your PC and try installing TWRP with Odin.
Just a reminder, volume down is next to the power switch. Also remember to unplug the power or you can't get into either download or recovery modes!
Installing TWRP Recovery:
I use TWRP, some good instructions are here You already have the drivers and Odin installed, so skip that part, and go to where he installs TWRP Recovery with Odin.
See if that gets you going. Then you can try flashing a stock ROM.
Or try flashing this ROM It is a rooted version of stock 4.2.2 with busybox.
Be sure and wipe Data/Cache/Dalvik Cache as he instructs. This should get you back to a stock, rooted ROM.
Click to expand...
Click to collapse
Ok, what does one do if one can't get to download OR recovery? It's starting to really P5113 me off!! I have been reading for two days now and still can't get this thing running. I've tried so many things I can't even remember them all. A friend wants to buy my tab 2, but I can't sell her a messed up tab. Somebody please help me out. I haven't been able to use Odin, no d/l mode. Can't even flash a recovery! Still can't get back to the basics and root the damn thang! There has to be a way to recover from this error "Firmware upgrade has encountered an issue". I'm ready to give it an issue of my own!

tab 2 10.1
after updating my tab2 10.1 using odin it failed and im in firmware upgrade encountered and the bad thing is i cant enter download or boot loader and also pc cant recognize it .please help .thxxxx

Sorry to necro bump, but did anyone find a fix to this? In the same situation. Thanks.

im in the same boat

Has anybody resurrected an Tab 2 when the Recovery Mode wont boot?
I bought a Tab 2 on Ebay, seemed he try´d to root it, and failed or the wrong Firmware.
Now i have it here, disassembled so i can cut of battery power and still, after an hard reset with no battery, i cant get with power + Volume up (or down) into download or recovery mode.
Is there any chance left or has the seller killed the nand flash partitions?
--
Lord Pinhead

Any Help Appreciated (softbricked Samsung Galaxy S III)

Several months ago I decided to root my phone, I installed cyanogenmod 11 I believe on my phone.
However today I decided I wanted the phone back to stock, so I backed up the files I wanted to keep (music and photos) and went to work.
I downloaded odin 3.07 connected my phone, set the device to download mode (volume down+power+home) and installed a stock ROM I found on sammobile.com
the ROM I used was "I9300XXUGMK6_I9300OXAGMK6_BTU".
The only ticked fields in odin were auto reboot and f.reset time.
I loaded the ROM into odin as a PDA.
The rom installed successfully (as far as i know) the phone when turning on no longer displays the cyanogenmod logo but now shows the samsung logo, however the phone never boots it's just stuck on the samsung logo.
Thankfully the phone can still be put into download mode, I thought maybe I installed the wrong ROM? So I went back to sammobile.com and installed "I9300XXUGNH4_I9300VFGGNH2_VOD" yet I still get the same result being stuck on the samsung logo.
I'm not bothered about having the phone stock anymore (I'll install a custom ROM if it comes to it) I just want my phone back!
I've had the phone for several years now, I live in the UK and have owned the phone from new, I bought it from a vodafone shop.
Any help here would be highly appreciated, thanks for reading and sorry mods if this is in the wrong section.

So after finding this thread http://forum.xda-developers.com/showthread.php?t=2426426
"Make sure phone is off. Boot into download mode. To do so, hold down the Volume Down, Home and then the Power buttons together until a Warning!! message is displayed on the screen. Here, press Volume Up to enter download mode. A green Android and the text Downloading will be displayed on the screen.
Now, open Odin by clicking on the Odin3 v3.07.exe file in the Odin307 folder which you obtained after extracting Odin307.zip
In Odin, click on the PDA button, then select the VRALEC.bootchain.tar.md5 file that you downloaded.
Important Untick every option under the “Option” section (on the top left of Odin), except F. Reset Time. Check the screenshot below for reference.
Then, connect the phone to the computer with the USB cable and wait for Windows to finish installing drivers. Odin will say Added!! in the message box on the bottom left if the phone is detected successfully. If not, make sure the drivers are installed and also try using a different USB port – preferably a USB port on the back if using a desktop computer.
Click on Start to start flashing the VRALEC.bootchain.tar.md5 file on the phone.
Wait till flashing is complete and you get a PASS message in Odin. When that happens, disconnect the phone from the computer, but DON’T turn it off and let it stay in download mode. Also close Odin.
Reconnect your phone to the computer (while it is in download mode). Open Odin again.
This time, click the PDA button and select the BOOTLOADER_I535VRALF2_618049_REV09_user_low_ship.t ar.md5 file that you download
Also, again untick every option except F. Reset Time in Odin. Then, click on the Start button to start flashing the BOOTLOADER_I535VRALF2_618049_REV09_user_low_ship.t ar.md5 file on the phone.
When flashing is complete and you get a PASS message, disconnect the phone and close Odin. But keep the phone in download mode, don’t turn it off.
Open Odin again and also reconnect the phone to the computer.
Click the PDA file and select the stock.vzw_root66.tar file that you Downloaded
[Important] Select the following three options in Odin on the top left: Auto Reboot, F. Reset Time, Nand Erase All. Check the screenshot below for reference.
Click Start to start the flashing process. Once the flashing is complete and you get a PASS message, the phone will automatically reboot. Disconnect the phone from the computer.
The phone will still not boot up completely. Now, remove the battery on the phone, then re-insert it. Don’t turn it on.
Now, boot into recovery. To do so, press and hold the Volume Up + Home + Power buttons together till the screen turns on, then let the buttons go. The phone will boot into recovery in a few seconds. You will see a few error messages in recovery, which is normal.
In recovery, use the volume buttons to scroll up/down and the home button to select options.
Select wipe data/factory reset, then select Yes on next screen to confirm. Wait a while till the data wipe is complete (this will NOT delete your personal files on the SD cards).
Select wipe cache, confirm, then wait for cache wipe to be completed.
Then, select reboot system now to reboot the phone.
The phone will now boot up properly into Android and is fixed, and you will be able to use it now."
I've looked into samsung galaxy s3 section and tried flashing VRALEC.bootchain.tar.md5 making sure only to tick f.reset time. However now odin appears to be stuck on NAND write start. Below is the output from odin:
"<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> VRALEC.bootchain.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!! "

S6 suddenly stuck at Samsung logo, impossible to enter recovery mode

My S6 suddely stopped working normally and gets stuck at the samsung logo. It was running with stock firmware, it was rooted and running very stable. (KNOX counter is tripped by doing that). Never had a sudden restart. I was running tomtom Go on it and during driving it happened. At home, I tried everything listed in the forums but without success.
I can run the recovery function from kies or smart switch via download mode, but after that, it does not get past samsung logo, and there is no way to enter recovery mode, no matter what key's I press during reboot.
Also, it seems it is not charging. Since I cannot switch off the phone (keys are not working), I can wait until it runs out of juice. When I connect a cable, or put in on a wireless charger, the samsung logo appears again and does not disappear. Unless I let it die, or unless I enter download mode.
When I disconnect my S6 from the cable, it stops very soon, so it seems the battery does not charge. Is there any suggestion to either enter recovery mode or to proof the battery is dead.

pwel said:
My S6 suddely stopped working normally and gets stuck at the samsung logo. It was running with stock firmware, it was rooted and running very stable. (KNOX counter is tripped by doing that). Never had a sudden restart. I was running tomtom Go on it and during driving it happened. At home, I tried everything listed in the forums but without success.
I can run the recovery function from kies or smart switch via download mode, but after that, it does not get past samsung logo, and there is no way to enter recovery mode, no matter what key's I press during reboot.
Also, it seems it is not charging. Since I cannot switch off the phone (keys are not working), I can wait until it runs out of juice. When I connect a cable, or put in on a wireless charger, the samsung logo appears again and does not disappear. Unless I let it die, or unless I enter download mode.
When I disconnect my S6 from the cable, it stops very soon, so it seems the battery does not charge. Is there any suggestion to either enter recovery mode or to proof the battery is dead.
Click to expand...
Click to collapse
bro , if you can't to enter to recovery you must reflash your firmware to get stock recovery or flash twrp recovery only by odin , the battery may be is too low you can try to charge device sometime when it is stuck on samsung logo

shiko2007 said:
bro , if you can't to enter to recovery you must reflash your firmware to get stock recovery or flash twrp recovery only by odin , the battery may be is too low you can try to charge device sometime when it is stuck on samsung logo
Click to expand...
Click to collapse
thx, I tried to get stock recovery and twrp recovery by Odin, both does not help. Also charging does not work: when I leave it on the charger for a full night (with Samsung screen on), it will switch off within 5 minutes. So it does charge only a bit.

i had a something like this happen, try this with the cable connected and charging hold volume down and power and menu button all at the same time until the logo hopefully goes of then let go of the buttons ( not the phone ) wait about 20 seconds to make sure the phone does not come back on and then press the volume up, power and menu buttons and keep holding till you see recover start
let me know if that helps

you can try to charge device when it in download mode

MrWolfman said:
i had a something like this happen, try this with the cable connected and charging hold volume down and power and menu button all at the same time until the logo hopefully goes of then let go of the buttons ( not the phone ) wait about 20 seconds to make sure the phone does not come back on and then press the volume up, power and menu buttons and keep holding till you see recover start
let me know if that helps
Click to expand...
Click to collapse
no, it always jumps back to Samsung logo. Also when I press the volume up/power/menu during restart it always gets back to the logo

Try do access download mode, reflashed the fw
After that it was fixed for me.

shiko2007 said:
you can try to charge device when it in download mode
Click to expand...
Click to collapse
I tried to charge in download mode but when I disconnect after 1 hr, it immediately turns off. Also with samsung screen it does not charge

pwel said:
I tried to charge in download mode but when I disconnect after 1 hr, it immediately turns off. Also with samsung screen it does not charge
Click to expand...
Click to collapse
ok bro, you can try to charge device also on warning page that come before enter to download mode ,
bro ,are the flashing process can complete when u connect device or when you begin to start flashing ,the device die quickly ?
can you post log of odin ?

shiko2007 said:
ok bro, you can try to charge device also on warning page that come before enter to download mode ,
bro ,are the flashing process can complete when u connect device or when you begin to start flashing ,the device die quickly ?
can you post log of odin ?
Click to expand...
Click to collapse
yes it completes and dies quickly. The log is:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1101)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Removed!!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)

ok bro , can you enter to recovery ? if yes , so do factory reset and wipe cash , if you can not access to recovery flash twrp recovery and make cf-root

Samsung j+J415FN Bricked after try root and TWRP (even download mode didnt start)

Hi i tryed root my j4+ and upload TWRP from
https://forum.xda-developers.com/galaxy-j4+/development/recovery-twrp-3-2-3-1-galaxy-j4-j415f-t3876876
First download from sammobile newest ROM
Samsung firmware for the Galaxy J4+ SM-J415FN with product code PRT from Poland (Play). This firmware has version number PDA J415FNXXU4BSF6 and CSC J415FNPRT4BSG1
unpack and flash by ODIN.
Everything was ok, phone boot normaly I did this 3 times and every time everything was ok., but still cant flash
twrp_3.2.3-1_sm-j415f_30319
so i dont know why again try flash ROM but this time in ODIN i flash
J415FXXU4BSF7_patched_boot
over orginal BL and this destroy my phone.
Phone start only when i press VOL+ + VOL- POWER, show logo Samsung, after about 5s i see droid robot for about 0,5s some error on screen but phone off then.
Can enter download mode.
I tryed every combination VOLs and POWER, nothing.
Only one time i enter download mode get msg than system is corrupted or smtg like that and press VOL+ do enter bl or VOL- to restart. But when i press + i enter bl mode but for about 1s and phone off.
<ID:0/003> Added!!
<ID:0/003> Removed!!
Click to expand...
Click to collapse
What can i do
Vid how start my Samsung
Sorry for baaaad quality but dont have anything good for record vids

GeoEgbA said:
Hi i tryed root my j4+ and upload TWRP from
https://forum.xda-developers.com/ga...ecovery-twrp-3-2-3-1-galaxy-j4-j415f-t3876876
First download from sammobile newest ROM
Samsung firmware for the Galaxy J4+ SM-J415FN with product code PRT from Poland (Play). This firmware has version number PDA J415FNXXU4BSF6 and CSC J415FNPRT4BSG1
unpack and flash by ODIN.
Everything was ok, phone boot normaly I did this 3 times and every time everything was ok., but still cant flash
twrp_3.2.3-1_sm-j415f_30319
so i dont know why again try flash ROM but this time in ODIN i flash
J415FXXU4BSF7_patched_boot
over orginal BL and this destroy my phone.
Phone start only when i press VOL+ + VOL- POWER, show logo Samsung, after about 5s i see droid robot for about 0,5s some error on screen but phone off then.
Can enter download mode.
I tryed every combination VOLs and POWER, nothing.
Only one time i enter download mode get msg than system is corrupted or smtg like that and press VOL+ do enter bl or VOL- to restart. But when i press + i enter bl mode but for about 1s and phone off.
What can i do
Vid how start my Samsung
Sorry for baaaad quality but dont have anything good for record vids
Click to expand...
Click to collapse
That's not download mode.
You're releasing the buttons too early. Hold POWER + VOL UP + VOL DOWN with USB cable inserted and attached to the PC.
DO NOT release until you see the download mode screen then release all buttons except vol up.
Also some things to note:
Details are very sketchy, what is meant by cannot flash TWRP?
Why are you flashing the older TWRP version?
Second, did you enable OEM UNLOCK and disable RMM lock?
Lastly, flashing a kernel cannot in anyway corrupt the bootloader.
If the bootloader was corrupted the device wouldn't even turn on.

ashyx said:
That's not download mode.
You're releasing the buttons too early. Hold POWER + VOL UP + VOL DOWN with USB cable inserted and attached to the PC.
DO NOT release until you see the download mode screen then release all buttons except vol up.
Also some things to note:
Details are very sketchy, what is meant by cannot flash TWRP?
Why are you flashing the older TWRP version?
Second, did you enable OEM UNLOCK and disable RMM lock?
Lastly, flashing a kernel cannot in anyway corrupt the bootloader.
If the bootloader was corrupted the device wouldn't even turn on.
Click to expand...
Click to collapse
Yes i Hold POWER + VOL UP + VOL DOWN with USB cable inserted and attached to the PC but its same like on movie, over and over even if I don't release the buttons, i hold buttons for 3min and over and over again the same as in the movie.
ODIN sad some error but rly dont remember what was that. I flashed twrp_3.2.3-1_sm-j415f_30319 from [RECOVERY][ROOT]TWRP 3.3.1-1 Galaxy J4+/J415F/FN/G/DS
Yes i enabled oem in Developer options which ended factory reset.
I also remember that I enabled Nand Erase in ODIN, maybe it will help something.

GeoEgbA said:
Yes i Hold POWER + VOL UP + VOL DOWN with USB cable inserted and attached to the PC but its same like on movie, over and over even if I don't release the buttons, i hold buttons for 3min and over and over again the same as in the movie.
ODIN sad some error but rly dont remember what was that. I flashed twrp_3.2.3-1_sm-j415f_30319 from [RECOVERY][ROOT]TWRP 3.3.1-1 Galaxy J4+/J415F/FN/G/DS
Yes i enabled oem in Developer options which ended factory reset.
I also remember that I enabled Nand Erase in ODIN, maybe it will help something.
Click to expand...
Click to collapse
Why did you enable Nand erase? That was probably a bad move.
Can you show a screenshot of the error in odin?
Again you haven't explained what the issue was flashing twrp?

ashyx said:
Why did you enable Nand erase? That was probably a bad move.
Can you show a screenshot of the error in odin?
Again you haven't explained what the issue was flashing twrp?
Click to expand...
Click to collapse
Yeah now i know that was baaaad idea to check it, but i dont know why i did that it seems to me that I have read somewhere that it is sometimes good to do a nand format because it can help. And about twrp error i will not help you i dont have screen with error and rly dont remember what was about.
So is there any chance to brink back to life my phone? is there any way to get chance flash ROM and PIT files?

Ok i download PIT for my J415FN/DS
J4PRIMELTE_CIS_OPEN.pit
Click to expand...
Click to collapse
newest ROM via SamFirm
SM-J415FN_1_20190801184101_lhpojveop9_fac
Click to expand...
Click to collapse
oraz ver 8.1
[up_vnROM.net]_J415FNXXU1ARIK_J415FNOXM1ARIK_DBT_8.1_FULL
Click to expand...
Click to collapse
But i cant enter download mode.
Ok so I noticed one interesting thing. namely, when I leave the phone not connected to the computer / charger and for about 20-30 min min I do not try to do anything, e.g. start the download mode after pressing vol + and vol- download mode starts, a window pops up asking whether to start the download mode and when I press vol + how to connect the download cable the mode turns on for a moment about 1s and restarts and could not turn it on again unless I wait the next 20 min
w ODIN dostaje log
<ID:0/008> Added!!
<ID:0/008> Removed!!
Click to expand...
Click to collapse

GeoEgbA said:
Ok i download PIT for my J415FN/DS newest ROM via SamFirm oraz ver 8.1
But i cant enter download mode.
Click to expand...
Click to collapse
Have you tried booting to Recovery mode? Hold POWER + VOL UP

try this. open Odin, then fill all files except home csc,then try to flash firmware. before you connect device push both vol+ and vol- and power button on same time then connect usb cable, and dont do anything untill you see download mode..i brick my device so many time and ALWAYS can flash firmware no metter what i screw. so try it.btw i have same device. just for Croatia sell.

ashyx said:
Have you tried booting to Recovery mode? Hold POWER + VOL UP
Click to expand...
Click to collapse
Yes, i did this at film in 1 post. First show logo Samusng then for about 1s show robot and phone go power off

rudi021 said:
try this. open Odin, then fill all files except home csc,then try to flash firmware. before you connect device push both vol+ and vol- and power button on same time then connect usb cable, and dont do anything untill you see download mode..i brick my device so many time and ALWAYS can flash firmware no metter what i screw. so try it.btw i have same device. just for Croatia sell.
Click to expand...
Click to collapse
Ok will do this in 20 min
O so in ODIN i set
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
and
now i waiting for start DL mode

GeoEgbA said:
I tried it but automatically after 1 second the phone reboots, I won't be able to click start. I will record a movie from the desktop and ODINA as it looks
Click to expand...
Click to collapse
yes i see your video,but i tell you dont connect usb BEFORE you push all buttons,so again first push all buttons(vol+,vol-,power button) and THEN connect usb.

rudi021 said:
yes i see your video,but i tell you dont connect usb BEFORE you push all buttons,so again first push all buttons(vol+,vol-,power button) and THEN connect usb.
Click to expand...
Click to collapse
Ok will do that, ODIN set set as in the pictures from the previous post

One more thing when i push all buttons and get warning when should push vol+ to continue first push and then connect usb?

GeoEgbA said:
Ok will do that, ODIN set set as in the pictures from the previous post
Click to expand...
Click to collapse
dont mess with odin and dont especially mess with PIT file. dont touch anything just open odin as admin as you wish,and fill up files and press start and press buttons then connect usb.thats it.no mess with anything. if you do something wich you dont understand you can use your device as paper weight.

rudi021 said:
dont mess with odin and dont especially mess with PIT file. dont touch anything just open odin as admin as you wish,and fill up files and press start and press buttons then connect usb.thats it.no mess with anything. if you do something wich you dont understand you can use your device as paper weight.
Click to expand...
Click to collapse
I did as you say and i was abble to flash, but in about 50% smtg happend
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1301)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 4267 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> aboot.mbn
<ID:0/009> sbl1.mbn
<ID:0/009> rpm.mbn
<ID:0/009> tz.mbn
<ID:0/009> devcfg.mbn
<ID:0/009> cmnlib.mbn
<ID:0/009> keymaster.mbn
<ID:0/009> apdp.mbn
<ID:0/009> msadp.mbn
<ID:0/009> NON-HLOS.bin
<ID:0/009> lksecapp.mbn
<ID:0/009> sec.dat
<ID:0/009> boot.img
<ID:0/009> recovery.img
<ID:0/009> vendor.img.ext4
<ID:0/009> system.img.ext4
<ID:0/009> __XmitData_Write
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
and now when i press vol + - and power phone ask do enter download mode but when press vol+ again phone enter download mode and about 1s after restat and flash on screen error " Use the Emergency recovery function in the Smart Switch PC software" and restart over and over. Now even when i connect the charger to the phone this error show and phone are restarting over and over. Also when i press vol + and - and power when show warning about enter download mode and then press power i get this
Now whether it connects the charger cable or the computer i get error with Smart Swith PC restart and again and again
To enter Download mode must press vol+ vol- and power then plug usb cable then show warning and when press vol+ phone start restarting over and over

GeoEgbA said:
I did as you say and i was abble to flash, but in about 50% smtg happend
and now when i press vol + - and power phone ask do enter download mode but when press vol+ again phone enter download mode and about 1s after restat and flash on screen error " Use the Emergency recovery function in the Smart Switch PC software" and restart over and over. Now even when i connect the charger to the phone this error show and phone are restarting over and over. Also when i press vol + and - and power when show warning about enter download mode and then press power i get this
Now whether it connects the charger cable or the computer i get error with Smart Swith PC restart and again and again
To enter Download mode must press vol+ vol- and power then plug usb cable then show warning and when press vol+ phone start restarting over and over
Click to expand...
Click to collapse
You have an issue with your cable. Use a different cable and ensure it is short.
Also when entering download mode release all buttons except VOL UP when you see the blue screen.
Pretty much the issue here is dodgy cables and pilot error.

ashyx said:
You have an issue with your cable. Use a different cable and ensure it is short.
Also when entering download mode release all buttons except VOL UP when you see the blue screen.
Pretty much the issue here is dodgy cables and pilot error.
Click to expand...
Click to collapse
I tried to connect the phone as you requested on 2 different computers and 1 laptop using 4 different USB cables including 1 Samsung original cable always the same result. Also, connecting the phone to different chargers using different cables gives the same result. The phone turns on and off. It also behaves the same when connected to a computer

GeoEgbA said:
I tried to connect the phone as you requested on 2 different computers and 1 laptop using 4 different USB cables including 1 Samsung original cable always the same result. Also, connecting the phone to different chargers using different cables gives the same result. The phone turns on and off. It also behaves the same when connected to a computer
Click to expand...
Click to collapse
I was referring to the Xmit_data_Write error. That is usually due to a faulty cable/USB port.

ashyx said:
I was referring to the Xmit_data_Write error. That is usually due to a faulty cable/USB port.
Click to expand...
Click to collapse
Ok i did it. finally I was able to upload a new rom. The phone switches on the operator logo and suddenly a prompt appears asking for the security code. What code? The message is telephone is encrypted for security
ok wipe data help. Thx a loooot!!

GeoEgbA said:
Ok i did it. finally I was able to upload a new rom. The phone switches on the operator logo and suddenly a prompt appears asking for the security code. What code? The message is telephone is encrypted for security
ok wipe data help. Thx a loooot!!
Click to expand...
Click to collapse
Good stuff.