Lava Iris X5 4G
- Android Lollipop 5.1 {Upgrade TO Marshmallow + VoLTE Support}
- 1.3 GHz MediaTek Quad Core Processor MT6735
- 2GB RAM With 16GB ROM
- Display 1280x720 pixels
- 5 Inch HD IPS Touchscreen Display With 296 PPI
- Dual SIM
- 13 MP Rear Camera With LED Flash
- 8 MP Front Camera With LED Flash
- 4G/WiFi/Bluetooth/FM
- 2500 MAh Battery.
Now we will go through a couple different methods that you can use to install the TWRP recovery. Before we get started, go ahead and enable USB Debugging on your device.
Download ADB FastBoot https://drive.google.com/file/d/0B0MKgCbUM0itNVB1elljU2NPR0k/view
Install ADB and Fastboot drivers
Enable USB Debugging In Your Phone
To enable USB debugging, navigate to Settings > Developer Options > USB Debugging
Install via ADB
Open the folder where your TWRP Recovery .img file is saved.
Then open a CMD window inside that folder. To do that, Shift + Right click on any empty white space inside the folder and then select Open command window here.
Connect your Android device to the PC. Type the following into the command window to boot your device into bootloader/fastboot mode:
"adb reboot bootloader"
If your asks for permission to “Allow USB debugging”, tap OK.
Once your device boots into bootloader mode, type this into the command line.
"fastboot flash recovery twrp-2.8.x.x-xxx.img"
{ Here modify twrp.img with the name of your TWRP recovery .img file.}
Once TWRP is successfully flashed on your device, type this final command to reboot your device.
"fastboot reboot"
Download TWRP
https://drive.google.com/open?id=0B6pSRZ7FopoYLVlSaTVtTlZlUEU
Hit Thanx If You Like
Credit Goes To @ Esiada
it worked thanks,, the only twrp which worked. flashed it with Magisk and worked.
Related
WALTON PRIMO H1 SPECS
CPU: Quad-core 1.2 GHz Qualcomm Snapdragon S4
GPU: Andreno 203
Rear camera: 8 MP
Front camera: 2 MP
RAM: 1 GB DDR
ROM: 4 GB
Display: 4.7 inch OGS IPS
Resolution: 960 x 540 pixel
Root Walton primo H1
Lets do this:
Download the Framaroot.apk from here . install it on your phone, Click Gandlaf to root. Reboot your Phone
Isn't it very simple !!!! to root your primo H1
Note: It may void your warranty, i will not responsible for your any kind of damage of your phone
CWM recovery for walton primo H1
# Install driver
Driver installation
1) Install AP part driver
Power off handset, press “Power key + Voice Up key” until the screen shows green, plug in usb cable, PC will remind you of installing new hardware. Unzip “ Driver”, select adb driver file, install AP driver.
Path: Right click on My computer>Manage>Device manager>Android(Yellow notification)>Update driver software>browse path> select adb folder >Continue anyway>finish
When you install AP driver successfully, you will find “Fastboot interface” in device manager.
2) Install BP part driver
(i) Power off handset, press “Power key + Voice down key” until the screen shows QPST mode, plug in 5Pin USB cable, Unzip “Driver”, select HK11-VB717-27_1.0.56 driver file, install BP driver.
Path: Right click on My computer>Manage>Device manager>Tiyanyu HS-USB Driver (Yellow notification)>Update driver software>browse path> HK11-VB717-27_1.0.56\Win32\x86\free >Continue anyway>finish.
(ii) When your BP driver is installed successfully, you will find Qualcomm HS-USB ports in device manager.
2nd step: download ” recovery.img “ and “Android AIO Flasher” file from here
4. Go to Fastboot mode in your phone by pressing Volume up + power key together ( Green Screen)
5. Connect your phone into PC via USB cable
3. Open “Android AIO Flasher”
5. Select recovery > Select file > Flash
Done!!! CWM recovery is successfully installed in your Walton Primo H1
i will not responsible for your any kind of damage of your phone
siva aggzz said:
WALTON PRIMO H1 SPECS
CPU: Quad-core 1.2 GHz Qualcomm Snapdragon S4
GPU: Andreno 203
Rear camera: 8 MP
Front camera: 2 MP
RAM: 1 GB DDR
ROM: 4 GB
Display: 4.7 inch OGS IPS
Resolution: 960 x 540 pixel
Root Walton primo H1
Lets do this:
Download the Framaroot.apk from here . install it on your phone, Click Gandlaf to root. Reboot your Phone
Isn't it very simple !!!! to root your primo H1
Note: It may void your warranty, i will not responsible for your any kind of damage of your phone
CWM recovery for walton primo H1
# Install driver
Driver installation
1) Install AP part driver
Power off handset, press “Power key + Voice Up key” until the screen shows green, plug in usb cable, PC will remind you of installing new hardware. Unzip “ Driver”, select adb driver file, install AP driver.
Path: Right click on My computer>Manage>Device manager>Android(Yellow notification)>Update driver software>browse path> select adb folder >Continue anyway>finish
When you install AP driver successfully, you will find “Fastboot interface” in device manager.
2) Install BP part driver
(i) Power off handset, press “Power key + Voice down key” until the screen shows QPST mode, plug in 5Pin USB cable, Unzip “Driver”, select HK11-VB717-27_1.0.56 driver file, install BP driver.
Path: Right click on My computer>Manage>Device manager>Tiyanyu HS-USB Driver (Yellow notification)>Update driver software>browse path> HK11-VB717-27_1.0.56\Win32\x86\free >Continue anyway>finish.
(ii) When your BP driver is installed successfully, you will find Qualcomm HS-USB ports in device manager.
2nd step: download ” recovery.img “ and “Android AIO Flasher” file from here
4. Go to Fastboot mode in your phone by pressing Volume up + power key together ( Green Screen)
5. Connect your phone into PC via USB cable
3. Open “Android AIO Flasher”
5. Select recovery > Select file > Flash
Done!!! CWM recovery is successfully installed in your Walton Primo H1
i will not responsible for your any kind of damage of your phone
Click to expand...
Click to collapse
how to install CWM on walton primo x1?
i just ported twrp 3.1.1-1 from libra to aqua, and it suport for OTA update
how to install :
- with adb fastboot :1. turn ur HH to fastboot mode
2. plug ur usb
3. open cmd on ur adb file directory
4. write "fastboot flash recovery twrp-3.1.1-1-aqua.img"
5. fastboot reboot
- with twrp(if u have installed twrp before)
1. save the recovery to ur sdcard
2. turn your recovery mode (press volume up + power button)
3. tap on install
4. tap on image
5. select the new recovery
*if u have stuck on logo install this
1. turn ur hh to fastboot mode
2. on cmd write "fastboot flash boot boot.img"
3. write on cmd "fastboot reboot"
ported by me, tell me if u have some trouble
link bellow
:laugh::silly::good::good:
twrp and boot image:
New TWRP 3.1.1-1-aqua (support OTA update)
en(dot)miui.com/thread-753595-1-1(dot)html
(Source: Xiaomi MIUI Official Forum)
Here is correct way to root your android P developers preview builds for one plus 6 without bricking anything and also enable pixel navigation gestures.
This is video guide for tutorial for easy uder standing
https://youtu.be/fwwZXQ9cn1w
Download :
1) twrp 3.2.1.0 img file(poot it on any folder on computer and rename it to simple twrp. Img) donts use any version except this.
https://dl.twrp.me/enchilada/twrp-3.2.1-0-enchilada.img.html
2)download magisk 16.7 zip and twrp 3.2.1.0 installer zip and olace them on sd card of one plus 6( use only this magisk version)
https://forum.xda-developers.com/ap...systemless-t3473445/post77108384#post77108384
Now boot your phone in fastboot mode using volume up and power long press
Connect phone to computer
No click shift+mouse right click and select open command frompt here vua drop down menu
Then type these commands.
Fastboot devices enter
Fastboot boot twrp.img
Then your phone will boot in twrp in twrp flash twrp installer first then flash magisk 16.7
Then reboot.
2) enabling pixel gestures :
Fisrt enable usb debugging via developers option
Then connect device via cable to computer.
Then type and enter these commands
adb devices
adb shell settings put secure swipe_up_to_switch_apps_enabled 1
Now reboot your phone
Go to button and gestures in setting and enable fixed navigation bar.
Thats it
After the command to enable the gestures my phone keeps telling me ''Oneplus launcher has stopped'' when trying to use it
tristanva said:
After the command to enable the gestures my phone keeps telling me ''Oneplus launcher has stopped'' when trying to use it
Click to expand...
Click to collapse
It it will happen for few sec then it works as normal. Or you can clear data for laungher and see
*C.M FLARE S7 CMW/PHILZ TOUCH CUSTOM RECOVERY*
[Tutorial]
Root not necessary*
No need to: ro.secure = 0 /off
REQUIREMENTS LISTED BELOW:
*Enable Developer Options [Turn On*]
*OEM Unlock [Optional*]
*Enable USB Debugging [Turn On*]
*Download C.M Flare S7 Recovery [Complete Set*]: https://drive.google.com/open?id=1SzTbVQ_dIiWdqj7cuB_17b9P5J1la4-C
------------------
Option 1: [Through SP FLASH]
Step1: Open SP FLASH Flash_tool.exe make sure to run as Administration.
Step2: On Scatter loading file, Choose MT6739_Android Scatter.txt file.
Step3: Select Download Only.
Step4: Uncheck all and Check the recovery only
Step5: Locate and Choose custom recovery.img file
Step6: After selecting the recovery.img file, press the DOWNLOAD button
Step7: Power off your phone and then remove the battery
Step8: Connect the phone USB cable and wait for 30 seconds
Step9: if the flashing has been successful, disconnect the cable then Press VOLUME UP + POWER Button.
Option 2: [Through ADB]
Step1: You should Enable USB Debugging mode before using adb
(Located in "Settings", "System", and tap 'About Phone' 7 times)
Go back to System Settings
Turn on: DEVELOPER OPTIONS.
Turn on: OEM UNLOCK & USB DEBUGGING.
Step 2: On your Computer, install "ADB-Setup-1.4.3" then after this software has been installed
Before you can use ADB you should Unlock the BOOTLOADER before flashing (this will wipe or reset the phone)
*make sure that the "OEM UNLOCK" is turned on*
On you computer open 'CMD' command.
-----------------------
Unlocking the OEM BOOTLOADER to enable the Flash feature on Fastboot*
you can use VOLUME UP + POWER BUTTON to go to Fastboot by selecting BootLoader Or ADB.
Option 1: using adb
Type:
adb devices
(Phone id will pop up in cmd with the list of 'DEVICES' attached)
adb reboot bootloader
(*in Fastboot type*)
fastboot oem unlock
(*Message will pop-up on your phone then Press VOLUME UP*)
(*To enable Flashing Custom Recovery Type command *)
fastboot flashing unlock_critical
(*Again Press VOLUME UP to enable*)
fastboot flashing get_unlock_ability
(*Queries bootloader to see if the device is unlocked*)
-----------------------
after unlocking the fastboot and oem bootloader
you can now Flash the Custom Recovery [CWM/Philz Touch 6]
in C.M FLARE S7 Folder Locate the CWM-Philz Touch 6 Custom Recovery
and copy the recovery.img file then
Type:
fastboot flash recovery recovery.img
(after flashing succeeded*)
Type:
fastboot reboot
(it will automatically reboot your phone)
-------------------------
*[End of tutorial]*
Tutorial
I flash it via flashify and ends with successful.
But i have notice that the recovery not working on touch button, anyway thanks for making this recovery.
How to fix?
Sir please tell me on How to fix Can't mount data on this custom recovery. I try to full backup using this recovery but its ended can't mount data. Sorry for my bad english I hope you can help me sir.
This is official tutorial on how to root your BLU Vivo XI (V0320VV) with Magisk.
Device Information::
Model: BLU Vivo XI (V0320VV) (https://www.gsmarena.com/blu_vivo_xi-9314.php)
Android Version: 8.1.0
(BLU promised they will push OTA update for Android 9.0 if that happen and you're running Android 9.0 don't follow this tutorial)
Baseband Version: MOLY.LR12A.R3.MP.V21
Kernel: 4.9.77
Requirement::
•Download
A. Unlock Bootloader
1. Make sure you have enabled "USB Debugging" on Developer options
2. Turn phone off.
3. Hold down VOL+ and then hold down Power key wait for phone to vibrate now release holding down Power key.
4. Now using VOL+ to scroll to the list and VOL- to select . Select "Fastboot Mode".
5.. Plug in phone via USB cable to your PC.
6.. Open ADB and type the following (Download ADB here)
Code:
fastboot devices
Code:
fastboot oem unlock
7. Wait for ADB to say "finished"
8. Now type the following
Code:
fastboot reboot
9. Your phone should restart and your bootloader is now unlock.
A. It's Magisk time
1. Install Magisk Manager and open it.
2. It should say "Magisk is not installed" now Click "Install"
3. Use "Select and Patch a file" as our method and then browse for the boot.img (provided from this thread)
4. Wait for Magisk to say "All done!"
5. Plug in phone via USB cable to your PC.
6. Now goto "My Computer" and Browse your phone "Internal Memory > Download" folder .
7. Now from the "Download folder" copy "magisk_patched.img" into your ADB installation folder.
8. Turn phone off.
9. Hold down VOL+ and then hold down Power key wait for phone to vibrate now release holding down Power key
10. Now using VOL+ to scroll to the list and VOL- to select . Select "Fastboot Mode".
11.. Open ADB and type the following
Code:
fastboot devices
Code:
fastboot flash boot magisk_patched.img
12. Wait for ADB to say "finished"
13. Now type the following
Code:
fastboot reboot
14. Your BLU Vivo XI should restart and now Rooted!
BlueTooth and WiFi No longer working
Sooo I rooted my Blu Vivo XI+ with Magisk and after reboot it factory reset my phone (Which is normal.) But what wasn't normal is that my wifi bluetooth and i believe cellular network no longer works. I also keep getting a message saying bluetooth has stopped working and bluetooth sharing has stopped working. anyone else having this issue?
I have the same issue.
same thing just happened to me. anyone got a fix? @Developerforbluvivios
brikinphones said:
same thing just happened to me. anyone got a fix? @Developerforbluvivios
Click to expand...
Click to collapse
Ok what is happening for some reason. When you flash magisk.. It wipes the imei number from the system for some reason. But the way to fix it copy down the original imei. Number if you can find it. If not look on the box. Then google imei fixer for mediatek I forgot what it is called but it's some where on xda . It's just like using the spflash tool. And/or to some ppl finding the rel.zip u flash with magisk for the Blu vivo xi+. But I don't understand what happens when u flash magisk and I had similar problems when I flashed the universal dmverity.zip.
Blu Vivo XI and BLU Vivo XI+ ARE 2 DIFFERENT PHONE ...
This guide is for Blu Vivo XI.
ineedroot69 said:
This is official tutorial on how to root your BLU Vivo XI (V0320VV) with Magisk.
Device Information::
Model: BLU Vivo XI (V0320VV)
Android Version: 8.1.0
(BLU promised they will push OTA update for Android 9.0 if that happen and you're running Android 9.0 don't follow this tutorial)
Baseband Version: MOLY.LR12A.R3.MP.V21
Kernel: 4.9.77
Requirement::
•boot.img
A. Unlock Bootloader
1. Turn phone off.
2. Hold down VOL+ and then hold down Power key wait for phone to vibrate now release holding down Power key
3. Now using VOL+ to scroll to the list and VOL- to select . Select "Fastboot Mode".
4.. Plug in phone via USB cable to your PC.
5.. Open ADB and type the following
Code:
fastboot devices
Code:
fastboot oem unlock
6. Wait for ADB to say "finished"
7. Now type the following
Code:
fastboot reboot
8. Your phone should restart and your bootloader is now unlock.
A. It's Magisk time
1. Install Magisk Manager and open it.
2. It should say "Magisk is not installed" now Click "Install"
3. Use "Select and Patch a file" as our method and then browse for the boot.img (provided from this thread)
4. Wait for Magisk to say "All done!"
5. Plug in phone via USB cable to your PC.
6. Now goto "My Computer" and Browse your phone "Internal Memory/ Download" folder .
7. Now from the Download folder copy "magisk_patched.img" into your ADB installation folder.
8. Turn phone off.
9. Hold down VOL+ and then hold down Power key wait for phone to vibrate now release holding down Power key
10. Now using VOL+ to scroll to the list and VOL- to select . Select "Fastboot Mode".
11.. Open ADB and type the following
Code:
fastboot devices
Code:
fastboot flash boot magisk_patched.img
12. Wait for ADB to say "finished"
13. Now type the following
Code:
fastboot reboot
14. Your BLU Vivo XI should restart and now Rooted!
Click to expand...
Click to collapse
Any chance you can get me a copy of that firmware? The link to it is not good anymore. I cannot get my Vivo to work with Verizon because I have the incorrect firmware, and BLU just can't seem to push it to my device. I have the Vivo XI. Thank you in advance.
For upload this method ..First Test your self !!!!
I have Vivo Xi too, and this **** broked my wifi and bluethoot
ineedroot69 said:
Blu Vivo XI and BLU Vivo XI+ ARE 2 DIFFERENT PHONE ...
This guide is for Blu Vivo XI.
Click to expand...
Click to collapse
I have Vivo Xi
Ok People, all OK
Flash VENDOR.IMG from 330ww or 320vv firmware Blu Vivo XI with ADB and the wife and Bluethoot back again !!!!!
Download any 2 firmware and unzip the same, copy de vendor.img to ADB carpet and Flash
Reuploaded the file and fixed some thread typos sorry for late reply ...
also i can't upload "system.img" do to the reason it's 2GB in size you just dump it once you have rooted your own phone anyway ...