Help! Moto Maxx XT1225 bricked "qualcomm 9008 mode" - Moto Maxx Q&A, Help & Troubleshooting

Hi everyone; my device is "bricked", only is recognized how to: "qualcomm 9008" mode.
I tried using "turbo unbrick" but i have errors; I attached one screenshot of error that appear.
I tried tutorials but not good results for me ..
I wait for your answers & help, many thanks, cheers!

try to flash a stock rom with RSDlite

NeoWave said:
try to flash a stock rom with RSDlite
Click to expand...
Click to collapse
Does not start in "fastboot" mode, it's dead; only "Qualcomm 9008" mode... I read about EMMC problem when commands fails, maybe "box JTAG" is the only solution.. I'm locked, i don't know, i not have more ideas; ¿"factory cable"?..
Thanks for your answer, cheers.

how did you brick it?

NeoWave said:
how did you brick it?
Click to expand...
Click to collapse
After unlocking the bootloader, flashing version was "QUARK_RETBR_5.0.2_LXG22.33-12.13_cid12" via "fastboot command", I do not remember where I got command message "failure", was extinguished and relit not ...

Related

[HELP]Hard bricked my HTC E8

I have hard bricked my E8 (China mobile single SIM version) by flashing the hboot:crying:
It can be recognized as Qualcomm HS-USB QDLoader 9008 in my computer
I cannot enter the download/recovery/fastboot mode
Anyway to unbrick the phone? Many thanks:crying:
tommychu said:
I have hard bricked my E8 (China mobile single SIM version) by flashing the hboot:crying:
It can be recognized as Qualcomm HS-USB QDLoader 9008 in my computer
I cannot enter the download/recovery/fastboot mode
Anyway to unbrick the phone? Many thanks:crying:
Click to expand...
Click to collapse
Hi,
Your situation looks very bad, mess up with boot partition and I only know earlier model HTC One M7 and sensation have tool to fix this problem. But unfortunately not available yet for M8/E8.
Please try to get information from the following thread :
http://forum.xda-developers.com/showthread.php?t=2770684
http://forum.xda-developers.com/showthread.php?t=1522351
http://forum.xda-developers.com/showthread.php?t=1674226
Or you can start to do unbrick project for E8?
Good Luck!
tommychu said:
I have hard bricked my E8 (China mobile single SIM version) by flashing the hboot:crying:
It can be recognized as Qualcomm HS-USB QDLoader 9008 in my computer
I cannot enter the download/recovery/fastboot mode
Anyway to unbrick the phone? Many thanks:crying:
Click to expand...
Click to collapse
You need a compatible good HBOOT in Hex format, which you can write using QPST.. That is what 3-4 minutes of searching tells me.
buggerman said:
You need a compatible good HBOOT in Hex format, which you can write using QPST.. That is what 3-4 minutes of searching tells me.
Click to expand...
Click to collapse
i have another working E8, but how can i back up my good hboot?
many thanks:crying:
tommychu said:
i have another working E8, but how can i back up my good hboot?
many thanks:crying:
Click to expand...
Click to collapse
Honestly, I have no idea..
But I'm sure you can backup your working phone using QPST and use the files from there.. You need to search more for "how to backup using QPST" or something..

hard brick my D838

afther install OTA my phone
- No Download mode
- No recovery mode
- Secure booting error
- but no recognized on device manager
any solution without disassemble the phone?
yulianov25 said:
afther install OTA my phone
- No Download mode
- No recovery mode
- Secure booting error
- but no recognized on device manager
any solution without disassemble the phone?
Click to expand...
Click to collapse
Was the device with root?
Did you used OTA from custom ROM
enkhtwshn said:
Was the device with root?
Did you used OTA from custom ROM
Click to expand...
Click to collapse
yes my device was rooted and has OTA from custom ROM
yulianov25 said:
yes my device was rooted and has ota from custom rom
Click to expand...
Click to collapse
that is a total gg
enkhtwshn said:
that is a total gg
Click to expand...
Click to collapse
any solution?
yulianov25 said:
any solution?
Click to expand...
Click to collapse
Have you tried the LG pc suite? I got out of many messes using it with my LG G3 similar to your problem, even when the pc didn't appear to recognise it. Look for the option in the menu : Repair upgrade errors.
Before you try this, plug your device into the pc and look in device manager and see if it shows up as:
QUALCOMM HS-USB QDLOADER 9008 (COM4) device
If it does, it's well and truly bricked I'm afraid and can only be repaired under warranty. This is not as bad news as it may seem, as if this has happened, they will not be able to tell that you have rooted your device or anything else for that matter.
bobsie41 said:
Have you tried the LG pc suite? I got out of many messes using it with my LG G3 similar to your problem, even when the pc didn't appear to recognise it. Look for the option in the menu : Repair upgrade errors.
Before you try this, plug your device into the pc and look in device manager and see if it shows up as:
QUALCOMM HS-USB QDLOADER 9008 (COM4) device
If it does, it's well and truly bricked I'm afraid and can only be repaired under warranty. This is not as bad news as it may seem, as if this has happened, they will not be able to tell that you have rooted your device or anything else for that matter.
Click to expand...
Click to collapse
I get same problem, my phone can not go to download mode and can not connect with PC after I flashed 5.0.1 by KDZ file (in Connectivity option of phone, I can not see and any option for USB connect).
Please kindly help me. Thank you very much!

Hard Bricked XT1032 QHSUSB_DLOAD

Hi.. Em.. I just bricked my phone.. I had CM12 and i tried to flash CM12.1 with that solution for 1+1
/watch?v=1J7nqguhTZ8
And i bricked my Moto G.. I flashed that file and tried to flash CM12.1 nightly 11/05, i saw again "Executed.. blablabla" so i pushed "reboot to system".. and my telephone.. Ya know..
Now in Device Meneger in Windows i only see "QHSUSB_DLOAD" what should i do? Guys.. Please :crying:
//Edit
I.. Do.. Something and now i've got "Qualcomm Qload 9008" and i know now i should usw blank flash, but.. It says me "could not open device"..
karacz105 said:
Hi.. Em.. I just bricked my phone.. I had CM12 and i tried to flash CM12.1 with that solution for 1+1
/watch?v=1J7nqguhTZ8
And i bricked my Moto G.. I flashed that file and tried to flash CM12.1 nightly 11/05, i saw again "Executed.. blablabla" so i pushed "reboot to system".. and my telephone.. Ya know..
Now in Device Meneger in Windows i only see "QHSUSB_DLOAD" what should i do? Guys.. Please :crying:
//Edit
I.. Do.. Something and now i've got "Qualcomm Qload 9008" and i know now i should usw blank flash, but.. It says me "could not open device"..
Click to expand...
Click to collapse
Well, a little more information would be helpful..
But if you have a working custom recovery installed, your phone is far from being hard bricked.
Just get hold of an USB otg cable:
http://www.amazon.de/BIGtec-micro-B...e=UTF8&qid=1431587181&sr=8-1&keywords=USB+otg
All you have to do is download the ROM of your choice (must be compatible with your bootloader) and copy it onto an USB stick and than boot into recovery (hold power + volume down button > select recovery).
From here you can do all the necessary wipes, backups etc (please search through XDA forum, you' ll find all the info).
Mount your USB stick and copy/flash ROM..
Again do some more reading first - it's all there..
Good luck!

I messed my S7 up... PLEASE HELP

Hi, I wasn't sure where to post this.
I was using Odin to reinstall the stock firmware for the Verizon S7, and then it won't turn on... In device manager, I see it is called qualcomm HS-usb qdloader 9008 (COM6)
Thank you for your help!
HuhhooXDA said:
Hi, I wasn't sure where to post this.
I was using Odin to reinstall the stock firmware for the Verizon S7, and then it won't turn on... In device manager, I see it is called qualcomm HS-usb qdloader 9008 (COM6)
Thank you for your help!
Click to expand...
Click to collapse
You cant even go in bootloader?
Us3rNam3d said:
You cant even go in bootloader?
Click to expand...
Click to collapse
No
Download samsung smartswitch and try to recover your phone from there.
Us3rNam3d said:
Download samsung smartswitch and try to recover your phone from there.
Click to expand...
Click to collapse
My phone doesn't turn on....
HuhhooXDA said:
My phone doesn't turn on....
Click to expand...
Click to collapse
Is it charged?
HuhhooXDA said:
Hi, I wasn't sure where to post this.
I was using Odin to reinstall the stock firmware for the Verizon S7, and then it won't turn on... In device manager, I see it is called qualcomm HS-usb qdloader 9008 (COM6)
Thank you for your help!
Click to expand...
Click to collapse
That sounds like you entered Qualcomm's download mode. Had encountered issues like that with HTC devices which ended with the device being sent back to HTC. Search around the HTC forums here on XDA. As before, the methods are device specific. But, maybe you'll get an idea. According to what I've read a long time ago, this happens when the device loses drivers for the chip or something. What happened exactly?

(Xiaomi MIX3) how to boot into EDL or 9008 mode?

MIX3 TestPoint method easy to damage the back cover,is there any other ways to boot into EDL or 9008 mode?
Thanks fpr ur help!or mail me:[email protected]
No Sir,
The only way is to open backcover
Some twrp versions can. The One from the Xiaomi EU Rom thread can,
Hunter6308 said:
MIX3 TestPoint method easy to damage the back cover,is there any other ways to boot into EDL or 9008 mode?
Thanks fpr ur help!or mail me:[email protected]
Click to expand...
Click to collapse
Not sure about perseus, but i had a problem with arb on my rn5pro. Was bricked after trying to install older version. Anyway many ppl said its necessary to open the back cover to enter 9008, but it wasnt.
Do you see the phone in the device manager? Or can you hear a sound if connected to pc?
I cant remember exactly, but i remember the flashing was simply a question of timing. I had to hit the flash button exactly at the point where u hear the "connected sound" on windows, cause the screen was black all the time, so speakers need to be on. I suggest you to google for "miui arb" or similar, do not try to open the back cover yet
phabet said:
Not sure about perseus, but i had a problem with arb on my rn5pro. Was bricked after trying to install older version. Anyway many ppl said its necessary to open the back cover to enter 9008, but it wasnt.
Do you see the phone in the device manager? Or can you hear a sound if connected to pc?
I cant remember exactly, but i remember the flashing was simply a question of timing. I had to hit the flash button exactly at the point where u hear the "connected sound" on windows, cause the screen was black all the time, so speakers need to be on. I suggest you to google for "miui arb" or similar, do not try to open the back cover yet
Click to expand...
Click to collapse
Thanks for ur reply! Xiaomi mix3 should be forbided to boot into EDL and 9008 port,i tried many tools finded on net,it does`t works now.
Hunter6308 said:
Thanks for ur reply! Xiaomi mix3 should be forbided to boot into EDL and 9008 port,i tried many tools finded on net,it does`t works now.
Click to expand...
Click to collapse
Sorry, but does it or doesn't it work now?

Categories

Resources