[Mt6580]Help needed in ROM porting - General Questions and Answers

I ported an aosp ROM (6.0.1) to my mt6580 phone following the online porting guides.everything works fine except that the screen sometimes flicker,and sometimes screen turns on 10-20 sec late after I press the power button I replaced opengles lib files,replaced zimage and vendor files but problem persists.what other files drive the display and how can I solve this problem?

What is name of your device? Do you have twrp recovery?

Related

Flashing Sapphire with Dream Images

I managed to flash a old proto (origional button config) with a image designed for the dream
http://forum.xda-developers.com/showthread.php?t=507151
The device boots fine but issue I have is that the touch screen now doesnt work...
Any ideas?
Flashed the device by downloading TheDudeAbides0.6.zip.signed
Renamed update.zip
Placed on root of MicroSD
Entered recovery mode (home + menu when restarting)
Pressed home + manu again and it started updating
When it the boots (takes ages), the tough screen is now working - Roller and hardware buttons are, just no touch screen.
You're not giving a very detailed explanation...
Does logcat tell you something about init problems?
What about syslog (dmesg)?
Have you checked that it included the hardware interface for that touch-screen? (It's a dream build afterall)
Also tried the Origional Sapphire images which have been used to build the Dream images - same problem.
Where are hardware drivers stored - Which *.img contain drivers? hboot or boot?
"boot" is the partition that stores kernel and ramdisk ("hboot.img" is the radio if i recall correctly).
Touchscreen driver are different for Dream and Magic. Can you try to add at your update.zip the boot.img from http://www.htc.com/www/support/android/adp.html ,twice driver are compiled, and don't forget to sign your zip file before install.

FaaastJB v2.5 running on Hipstreet Flare (Easy fix)

Hello there, for anyone with a Hipstreet FLARE (HS-9DTB4) who has had the nightmare of trying to find a ROM for it, I have a solution!
These models typically come from Canada, like myself, although I don't know if it's exclusive. I spent many hours modding operating system files when I almost accidently came up with a MUCH easier solution.
This instructional assumes you have installed your USB drivers and have a copy of ADB
1: BACK UP YOUR ROM
(if you're like me and you lost the original you can probably skip this)
2: Follow the instructions at A13 ROM JB 4.2.2 + DRIVERS and install FaaastJB v2.5 (4.2.2).
Once installed, your touchscreen and gsensor will NOT work
3: Download the TS driver from the installation link: - ft5x_ts, goodix_ts, gslX680, nt11003+mxc32x0
4: Unzip the file to your ADB directory
5: Open the file 'setupsensors.sh'
Remove this line: insmod /system/vendor/modules/mxc32x0.ko
6: Insert this:
Code:
#9inch
insmod /system/vendor/modules/ft5x_ts.ko
insmod /system/vendor/modules/goodix_ts.ko
insmod /system/vendor/modules/nt11003.ko
# insmod /system/vendor/modules/ssd253x_ts.ko
# insmod /system/vendor/modules/ssd2533_ts.ko
insmod /system/vendor/modules/gslX680.ko
#7inch
# insmod /system/vendor/modules/gt811.ko
# insmod /system/vendor/modules/gsl1680.ko
# insmod /system/vendor/modules/ssd253x_ts.ko
# insmod /system/vendor/modules/sitronix_ts.ko
# insmod /system/vendor/modules/pixcir_touch_811.ko
# insmod /system/vendor/modules/gslX680.ko
#insmod G-sensor driver
insmod /system/vendor/modules/mma7660.ko
# insmod /system/vendor/modules/mecs.ko
# insmod /system/vendor/modules/mxc622x.ko
# mkdir /data/misc/sensors 0777 system system
-- Loading these modules into other A13 ROM is possible but I couldn't for the life of me get the WIFI working (properly), except in FaaastJB.
7: Connect your Hipstreet FLARE via USB and execute the 'run.bat' that came with the TS modules.
8: Enjoy having Google Play on your (crappy) Hipstreet Flare
Not sure if I like the new launcher, but thanks for pointing me toward the newer faastjb.. dunno if I like the bootscreen either..
ANYHOW.. In the past, on my Hipstreet Flare, I was using the gt_828 ? driver.. and it seemed to work, however, I never bothered getting the sensors working/etc.. However I would like the camera to work, and, it doesn't seem to with these drivers / this rom .. (crashes when opening cam app)
Mucho thanks for posting the drivers to use with the Flare, touch and gsensors seem to be working fine.
And many thanks to Toxicro for making the rom etc !
As a newbie to flashing android, I thought I might point out that when you edit the 'setupsensors.sh' file, do NOT use notepad.
Notepad++ seems to work fine (it is compatible with this file format).
I used Livesuit 2 to flash, and did have trouble getting the driver to load. Best I could get was a USB - unknown device showing in device manager.. but from there it was easy enough to argue with Win7 and finally manage to manually point to the Livesuit/driver folder.
One thing I noticed, is that you can still get into a recovery mode with FAAST-JB.
In the stock Flare, from power off, you hold the Vol- and Power until the unit responds, then start pressing Power repeatedly (while holding Vol-). With Faast-JB loaded, you have to hold the Vol+ instead (since the keys are reversed in the flash, no biggie).
This now brings up a CWM recovery screen.
I would think that Backup and Restore probably work fine.
But what about "Install zip from sd card" ?
Would this work for further flashing, or would that not be recommended due to the odd structure of these A10/13 devices ?
Any original rom to Hipstreet FLARE HS-9DTB4-4GB
Dave
Thanks a lot, first i use notepad to edit and G-sensor dont go... now user notepad++ y i am back the g-sensor.
However, i lost the camera i read about edit some BIN file, mi tablet is a oldie Hipstreet FLARE HS-9DTB4-4GB without Google Play, i flashing to get this market and now have the problem, i need solve the camera problem or almost get the original ROM to this model .
* what program edit script.bin??
Thanks again
DaveCarp said:
Mucho thanks for posting the drivers to use with the Flare, touch and gsensors seem to be working fine.
And many thanks to Toxicro for making the rom etc !
As a newbie to flashing android, I thought I might point out that when you edit the 'setupsensors.sh' file, do NOT use notepad.
Notepad++ seems to work fine (it is compatible with this file format).
I used Livesuit 2 to flash, and did have trouble getting the driver to load. Best I could get was a USB - unknown device showing in device manager.. but from there it was easy enough to argue with Win7 and finally manage to manually point to the Livesuit/driver folder.
One thing I noticed, is that you can still get into a recovery mode with FAAST-JB.
In the stock Flare, from power off, you hold the Vol- and Power until the unit responds, then start pressing Power repeatedly (while holding Vol-). With Faast-JB loaded, you have to hold the Vol+ instead (since the keys are reversed in the flash, no biggie).
This now brings up a CWM recovery screen.
I would think that Backup and Restore probably work fine.
But what about "Install zip from sd card" ?
Would this work for further flashing, or would that not be recommended due to the odd structure of these A10/13 devices ?
Click to expand...
Click to collapse
Please, can you send me the file. I got bootloop in every variant. I flashed tousends times.
Thanks!
Edit: Sorry, I quoted wrong post.
HipStreet Flare 1 working firmware 95%
HS 9dtb4-8GB Hipstreet Flare (1) running on
MaPan_MX913_DC_Jelly_Bean_4.1os_Root_
Firmware_D201 30601_UP
Only missing top inch of TS, looking here about injecting just the TS driver, or can someone tell me how to ajust my TS touching surface.

[GUIDE][CM Port][ MT6589 only] Port CyanogenMod 10.2/11 for all MT6589 devices

@chrmhoffmann compiled first ever CyanogenMod for his Wiko Stairway which is a MT6589 device and made it possible for other MT6589 users to taste CM. Since then many are porting it to their MT6589 device and many are requesting to make a port for their device. So, I have made a guide here to make it easier for them to port themselves. You should give proper credits to respected developers and hit thanks before posting on XDA.
NOTE:I have made a list of already ported CM roms in #2 post below , if your device is not listed there download any of the ported CM rom and follow this guide to port it to your device
This is the guide to port CM 10.2/11 for all MT6589 devices.Read carefully and follow each step correctly otherwise CM won't boot
Tools Required:
1) Archive Manger (winrar,winzip,7zip)
2) boot.img Unpack Repack Tools
http://forum.xda-developers.com/showthread.php?t=1587411(For Linux)
http://forum.xda-developers.com/showthread.php?t=2036528(For Windows)
NOTE:
For CM 11 the same proceedure is followed but the stock boot.img must be having kernel with binder.c patched and SELinux enabled (This feature can be bypassed but binder.c patch is must otherwise CM 11 won't boot)
Guide:
1) First get your stock rom and download any ported CM 10.2/11 rom from #2 post below
2) Get boot.img from your phone(stock rom) and boot.img from downloaded CM-ROM.zip
3) Unpack both of them to get ramdisk and kernel of both.
4) Repack CM's ramdisk and stock kernel (your phone's) to get a new boot.img
5) Extract system folder from your phone(stock rom) and system folder from downloaded CM-ROM.zip
6) Copy and replace these files from stock to CM,
=> /lib/modules/ -> all files
=> /framework/ -> CustomProperties.jar
mediatek-common.jar
mediatek-framework.jar
mediatek-op.jar
secondary-framework.jar
=> Also all the files mentioned in the below link ( A great thanks to Kashifmin for providing this )
https://github.com/kashifmin/android_device_micromax_a116/blob/master/proprietary-files.txt
7) Now take the modified CM system folder and the new boot.img and make a zip archive with normal deflate compression ( are default in 7zip)
8) Open the newly created zip archive and downloaded CM-rom.zip .Now drag and drop the META-INF and file_contexts from downloaded CM-rom.zip to newly created zip archive.
9) Now flash the new zip using recovery (CWM/TWRP)
10) Enjoy !!
CREDITS:
@michfood for his Boot unpack/repack utils for WINDOWS.
@bgcngm for his Boot unpack/repack scripts for LINUX.
@kashifmin for his proprietary-files.txt
@kashifminfor guiding me.
@chrmhoffmann For bringing the first ever CM10.2 for an MT6589 device.
@XpLoDWilD
@Dr-Shadow
OmniROM project.
Available CM port builds for MT6589
CM 10.2 builds:
Wiko Stairway / MMX Canvas 4 (A210) -> http://forum.xda-developers.com/showthread.php?t=2467400
MMX Canvas HD (A116) -> http://forum.xda-developers.com/showthread.php?t=2673367
XOLO Q700/Q700i -> http://forum.xda-developers.com/showthread.php?t=2675963
LAVA 458Q / XOLO Q600 / CROSS A88 -> http://forum.xda-developers.com/and...-cross-a88-t2814034/post54103404#post54103404
CUBOT GT99 / Cherry Apollo / XYZ X1 -> http://forum.xda-developers.com/and...cubot-gt99-t2834832/post54542482#post54542482
CM 11 builds:
Wiko Stairway / MMX Canvas 4 (A210) -> http://forum.xda-developers.com/showthread.php?t=2676086
MMX Canvas HD (A116) -> http://forum.xda-developers.com/showthread.php?t=2676896
ACER liquid e2 v370 -> http://forum.xda-developers.com/showthread.php?t=2766290
MMX Canvas Magnus (A117) -> http://forum.xda-developers.com/canvas-magnus/development/rom-cyanogenmod-11-canvas-magnus-a117-t2790957
MMX Canvas 2+ (A110Q) / Fly IQ450 -> http://forum.xda-developers.com/mic...-2-cyanogenmod-11-port-canvas-2-plus-t2750867
MMX Canvas Turbo (A250) -> http://forum.xda-developers.com/canvas-turbo/development/rom-cyanogenmod-11-canvas-turbo-t2780905
If CM for any MT6589 device is missing here , PM me. I will add here.
i try but always stuck on boot splash, no boot up.. pleash help thanks
Uhm.... I guess I can't port cm10.2 over stock jb4.2.1 rom, right?
I ask because I first looked for cm10.1 to port, but to my surprise, I didn't find any cm10.1 builds for any mt6589 on google.
@polfrank you can port CM 10.2 using stock 4.2.1 rom. First you have to download any CM 10.2 Rom from above and follow guide to port. You can even port above CM 11 Roms if you have a working kernel source for your device
Sent from my iris458Q using XDA mobile app
@limam27 boot loop occurs if 1) boot.IMG is badly repacked 2) any file is missing from your device stock rom which has to be copied to CM ROM as mentioned in the guide. Check them first . Also Check whether you are getting errors during unpack and repack of boot.IMG.
Sent from my iris458Q using XDA mobile app
Hmm, I'm stuck on my brand's splash screen too. I don't get to see the boot animation, and as you mention I get errors during both unpacking and repacking. But it said that the file was copied though.... I 'll search for another way to upack and repack on Google and come back.
Edit: pfff, seems like the only way to do it on windows was the one you provided...
Which CM version you are trying to port ?
If have Linux use unpack scripts to unpack/repack boot.img
Windows always gave me errors.
Sent from my iris458Q using XDA mobile app
4shreyas said:
Which CM version you are trying to port ?
If have Linux use unpack scripts to unpack/repack boot.img
Windows always gave me errors.
Sent from my iris458Q using XDA mobile app
Click to expand...
Click to collapse
I chose the CM10.2 from Wiko Stairway.
Yes, I'm now setting a Virtual Machine with Linux 14. And I'll try the unpack scripts from there. Let's see...
UPDATE:
OK, i ended up doing a clean install of ubuntu.
I upacked both images SUCCESS.
I repacked using stock kernel.img and CM ramdisk folder, SUCCESS.
I Install boot.img through CWMrecovery, it now gets past boot logo(Cubot white screen) but I think that before it would enter bootanimation the screen becomes a weird mass of colours, as if the screen was broken. It lasts for 1 second, then it restarts.
ps. I can successfully go to recovery with power+volUP If i like..
Any ideas?
You should get CM boot animation even if you use stock boot.img but won't boot. Did u correctly replace all required files in rom ? Do a clean one. Check if you can get logcat. Send me the logs
Sent from my iris458Q using XDA Premium 4 mobile app
4shreyas said:
You should get CM boot animation even if you use stock boot.img but won't boot. Did u correctly replace all required files in rom ? Do a clean one. Check if you can get logcat. Send me the logs
Sent from my iris458Q using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I think I used wrong kernel.img. I repacked, will flash soon and come back to report.
EDIT: Are you sure that I have to use the META-INF folder from the CM rom? It gives me status 7 error.... (I also used the META-INF from a rom for my device, unfortunatelly it uses aroma, but it seems to install properly..)
EDIT2: I think that now I repacked the correct components of boot.img. It seems to get past the Cubot white splash screen, but after this, I get a black screen, but I can see that the screen is on, I can see the backlight. [I will try again with the CM META-INF-->still fails]
ps. Seems like I have to learn how to get a logcat if I wanna make use of your help... I'll be back in some hours.
----------------------------------------------------------------------
To sum up:
I have packed the new boot.img and replaced the needed files in the rom.
1) With the CM's META-INF folder I can't install, status 7 error.
Finding update package...
Opening update package...
Installing update...
assert failed: getprop("ro.product.device") == "stairway || getprop("ro.build.product") == "stairway"
E: Error in /sdcard/experiment/cm102last.zip
(Status 7)
Installation aborted.
Click to expand...
Click to collapse
2) With the stock rom's META-INF it seems to install propperly.
After reboot from recovery it goes to a black screen and stays there. I tried to logcat (adb logcat -v long > port.txt) but it just says:
[email protected]:/home/pol/Documents/sdk/platform-tools# adb logcat -v long > port.txt
- waiting for device -
Click to expand...
Click to collapse
If i write adb devices it says :
[email protected]:/home/pol/Documents/sdk/platform-tools# adb devices
List of devices attached
0123456789ABCDEF offline
Click to expand...
Click to collapse
When I am on recovery I get:
[email protected]:/home/pol/Documents/sdk/platform-tools# adb devices
List of devices attached
CWM-ZTE-V967S recovery
Click to expand...
Click to collapse
---------------------------------------------------------------------------------------------------------------
CONCLUSION: I managed to install the new boot.img and rom but it stops on a black screen, right after it passes from the white logo screen. And now, I need your ideas...
ps. I repeated the porting process from the beginning to make sure that I didn't make any mistakes... again, the same result.
--------------------------------------------------------------------------------------------------------------
NEW UPDATE: IT BOOTED!! but how....? Here it is........
I just replaced the boot.img from the wiko stairway flashable zip with the boot.img I created with repacking my phone's kernel and CM's ramdisk.
SO, I just changed the boot.img !!!! Testing.......
-------------------------------------------------------------------------------------------------------------
Testing results: buggy mobile network and sound not working. I guess this is why all those files are needed to be copied. I think I ll start copying..... But I wonder...what did I do wrong earlier while copying,,,?
You will get status 7 error because it is a security feature which doesn't allow to flash one device's ROM to other. You have to edit using any text editor and remove first line in the update-script found in meta-inf/com/Google/android/
Also don't use other rom's meta-inf as they have different symbolic links which may not boot the device.
Your phone's modules will be different from wiko's. That's why you got buggy audio and network. Replace all the mentioned files.
sent from my iris458Q using XDA mobile app
Okay, after some hours of trial and error I copied all the porting files provided in the op, except 2:
-libjpeg.so - When I port this from stock, Cm boots, but cannot show images, every single image, including the bootanimation is black.
-libmedia.so - When I port this from stock, Cm stays in the bootanimation forever. (No bootloop, just bootanimation forever)
-------------------------------------------------------------------------------------------------------------------------------------
The "extra" bugs that I have are:
1. No sound from the speaker (but yes in the headphone).
2. Weak signal. I don't know if this is normal. It has 1 bar and sometimes it has 0 and says no service. Also, the name of the tile in the QuickSettings is 20201 (weird...). I also get a message when the rom boots and it says: "Restricted Access changed. Data service is blocked." This appears sometimes at random too.
3. USB storage doesn't work through Android.... ( I don't know if this is normal too). When I plug it on PC it just charges. (Note: I now see that other devices have this problem too. I found a partial workaround in the MMX Canvas HD cm10.2 section)
PS. Would logcat help in any of these problems?
--------------------------------------------------------------------------------------------------------------------------------
I moved on, and took some adb logcats.
1. I took the audio.txt as follows: started logcat, pressed play on the apollo widget, pressed pause, stopped logcat
2. I took the signal.txt as follows: started logcat (while on Airplane mode), disable Airplane mode (from quickSettings tiles), enable mobile data, disable mobile data, enable Airplane mode, stop logcat
I'll look at logs meanwhile I never had problem with signal, speaker audio and images. To get USB storage working add these lines to build.prop and reboot
persist.sys.usb.config=mass_storage,adb
persist.sys.usb.config=mtp,adb
For signal issue , did u replace your modem.IMG in CM ROM ?
For image issue try those 2 files from wiko ROM.
Edit:
Try to freshly port CM once again as given in guide with some changes in meta-inf and build.prop as I gave. If you still have problems then report here.
I couldn't debug audio log but in signal log > network is disconnected as data is enabled and even it's saying messaging settings are false. There may be issue with modem.img
sent from my iris458Q using XDA mobile app
Thanks for the USB storage tip. At least the internal SD can be seen now by the computer.
Images are OK now with the lib of CM.
For signal issue I copied modem.IMG from stock into the CM rom, and still having problems.
Btw, I just created a new thread for my device, I hope this is not a problem.
http://forum.xda-developers.com/and...cubot-gt99-t2834832/post54542482#post54542482
Cheers !! I'll add your device in the ported list. As I said previously all necessary files should be replaced in CM to be bug free except major BT,camera,hwcomposer,FM,GPS,2nd Sim bugs.
Also USB storage is buggy now as SD card is unmounted in mass storage mode but not mounted on PC and when disconnected from PC it doesn't get mounted and you have to reboot to get it working on android. Also mtp mode sometimes doesn't work
sent from my iris458Q using XDA mobile app
Nice!
The only file missing is /lib/libmedia.so and I 'm starting to think that this may be the cause of the sound bug. But when I copy it from the stock rom, I get boot problems...
Anyway, thanks for your help, and sorry that I messed up/spammed your thread. I think the most important part of the job is done..! Good job!
EDIT: I think I sort of fixed the mobile network issue. I used a modem.img from another version of stock rom and it seems to work. However I still get the error "Restricted Access changed. Data service is blocked." But I have full signal and 3G! It's something!
Restricted access notification occurs if you enable or disable data and turn on/off airplane mode and phone and it is not a issue I think. It may be cyanogenMod's security message or something.
Also try libmedia.so from other
Stock rom which you said above.
sent from my iris458Q using XDA mobile app
thanks for repley
4shreyas said:
@limam27 boot loop occurs if 1) boot.IMG is badly repacked 2) any file is missing from your device stock rom which has to be copied to CM ROM as mentioned in the guide. Check them first . Also Check whether you are getting errors during unpack and repack of boot.IMG.
Sent from my iris458Q using XDA mobile app
Click to expand...
Click to collapse
I want to port my device MT6589T JB 4.2 to cm11 kitkat but I do not know how to activate the binder c in the boot.img.
I've tried without a binder c install process always aborted status 7
please help thank you
Hello @limam27
@Iimam27 said:
I want to port my device MT6589T JB 4.2 to cm11 kitkat but I do not know how to activate the binder c in the boot.img.
I've tried without a binder c install process always aborted status 7
please help thank you
Click to expand...
Click to collapse
You can't patch binder.c from boot.IMG. You must be having kernel source for your device and you must patch binder.c in kernel. If you don't have kernel source then its almost impossible to get KitKat. See if your device clones have kernel source for their device. Else look for almost similar specs device with same processor. My device has mt6589m but no source from vendor. I used similar mt6589m device's source to build kernel. Now CM 11 is booting but no display due to different GPU config. So it's really hard if you don't have source. Try with CM 10.2 first .
EDIT- Previously I have told why you get status 7 error. So read whole thread before posting here. Good luck
Sent from my iris458Q using XDA Premium 4 mobile app

(GUIDE)(PORT CM 12.1 ) MTK6592 CM 12.1 PORTING GUIDE (Only For Porters) :)

MT6592 CM 12.1 PORTING GUIDE
Lots of people asked me how i ported cm 12.1 from @fire855's compiled rom for kingzone k1 Turbo
First of all huge thanks to @fire855 and other Dev who helped him for bringing cm 12.1 on mt6592
Give support to him via pressing thanks or Donate , here is it's Link : http://forum.xda-developers.com/and...od-12-kingzone-k1-turbo-t3119908#post61000671
Requirements :
1. Stock Rom KK
2. Working Good Custom Recovery
3. Good Porter and Mind
Lets Start This Short Guide :
1. Download Latest Cm 12.1 from above link
2. Extract in a new folder
3. Use this tool LInk : http://forum.xda-developers.com/android/development/tool-convert-folder-to-ext4-format-t3099237
unpack .dat file and copy extracted system folder in new folder as stated in step 2.
4. Using @michfood's tool (link : http://forum.xda-developers.com/showthread.php?t=2036528)
change Kernel and Do necessary changes acc. to your stock's ramdisk
5. Copy new boot.img that created in step 4 and replace in new folder as stated in step 2.
6. From stock kk rom ...........extract libaudio.primary.default.so (system/lib) and modem.img (system/etc/firmware) nd replace in cm 12.1 's rom ................ in the same location
7. Delete meta-inf folder of cm 12.1's rom and extract this (link : https://www.sendspace.com/file/vnf0gi)
8. Open meta-inf's updater-script in notepad++ and change mountpoint of system acc. to your's phone
9. Pack the folder as in zip format and flash via recovery
( meta-inf, install ,system, boot.img, file context these files must there in zip )
10. Voila Rom booted .............if not comment
If Rom Booted ..............Follow this steps :
1. Download this apk (link : http://forum.xda-developers.com/showthread.php?t=2524485)
2. Go to Settings>developer>enable root and install apk from step 1
3. Open app and Set as permissive ,reboot Your device
4. Voila your wifi,bluetooth etc will start working, even Dual Sim
5. If you faced basedband unknown that mean restore your imei
6. For Home Key Bug , Edit generic.kl and mtk-kpd.kl (system/user/keylayout)
7. For Storage Bug, Edit Framework-res.apk and set sdcard1 as primary and edit boot's ramdisk MT6592.rc, fstab
8. For Other Bugs, Let Me Know
Notice : Always give thanks and link of @fire855's Rom Link
Credits : everyone (who's name i added in this guide and there's tools )
​
@[email protected] Thanks for a great guide, I was able to succesfully port the rom and it booted as well and after setting the selinux to permission my sims also started working but mic is not working, my device is MT6582 (Intex Aqua Speed). I have a working CM11 already ported for my device which is working perfectly fine. Also the soft keys (capacitive keys are not working nor even the power button). Please advise...
contactwajeeh said:
@[email protected]. . . . but mic is not working . . . .
Click to expand...
Click to collapse
The microphone is also not working in all apps (except Telephone where it work's fine) in the original CM12.1 by fire855 for the Kingzone K1. (The Rom this Porting Guide is based on).
That could be part of the problem.
Dominic
G-GFFD said:
The microphone is also not working in all apps (except Telephone where it work's fine) in the original CM12.1 by fire855 for the Kingzone K1. (The Rom this Porting Guide is based on).
That could be part of the problem.
Dominic
Click to expand...
Click to collapse
But its not working in calls as well. BTW I am using @moonrotation build as my base. I haven't asked for permissions to port it yet. But that should be fine as far as I dont do the public release of it.
What necessary changes i must do in ramdisk?help
contactwajeeh said:
But its not working in calls as well. BTW I am using @moonrotation build as my base. I haven't asked for permissions to port it yet. But that should be fine as far as I dont do the public release of it.
Click to expand...
Click to collapse
currently mic problem is there ....wait for fixes
contactwajeeh said:
@[email protected] Thanks for a great guide, I was able to succesfully port the rom and it booted as well and after setting the selinux to permission my sims also started working but mic is not working, my device is MT6582 (Intex Aqua Speed). I have a working CM11 already ported for my device which is working perfectly fine. Also the soft keys (capacitive keys are not working nor even the power button). Please advise...
Click to expand...
Click to collapse
edit keylayout's genric.kl etc
mirrr46 said:
What necessary changes i must do in ramdisk?help
Click to expand...
Click to collapse
like some some extra lines der in urs .
Tried to port this, Device reboots right after vendor logo
I compare stock Ramdisk with CM12. There are no diff. At end both have same values. I changed Kernel and Kernel Header
I changed the updater script so it fits to my partition. It gave me strange errors:
lsetfilecon of /system/lost+found to ubject_r:system_file:s0 failed: No such file or directory
m_file:s0 failed: Operation not supported on transport endpoint
Error flashing Zip : Failed
Updating partition details...
Click to expand...
Click to collapse
Also @michfood's tool just ain't work here, i took the v4 for my x64 win8.1. The Program is unable to extract the Ramdisk path, so i was forced to use "MTK Firmware Adapter Tool"
Recovery:TWRP 2.8.1.0
SoC:MT6592
Device: Doogee DG550
Traace said:
Tried to port this, Device reboots right after vendor logo
I compare stock Ramdisk with CM12. There are no diff. At end both have same values. I changed Kernel and Kernel Header
I changed the updater script so it fits to my partition. It gave me strange errors:
Also @michfood's tool just ain't work here, i took the v4 for my x64 win8.1. The Program is unable to extract the Ramdisk path, so i was forced to use "MTK Firmware Adapter Tool"
Recovery:TWRP 2.8.1.0
SoC:MT6592
Device: Doogee DG550
Click to expand...
Click to collapse
1. don't touch kernel header....change only kernel
2. u should try other recovery like philz
3. delete lost and found folder if present
4. use my meta-inf only....just change mountpoint of system........it seems u need good recovery with lp supported or philz recovery :fingers-crossed:
Thanks for guide.
My camera does not work and gallery does not see SD card.
How to fix it?
mirrr46 said:
Thanks for guide.
My camera does not work and gallery does not see SD card.
How to fix it?
Click to expand...
Click to collapse
1. camera icon in launcher is issue (for mt6592)
2. for storage...fixes r from mt6592.rc in this file read proper sysmlink and do changes acc. to it ,decompile framework-res.apk....set sdcard1 as primary ,fstab changes also needed
Enforcing to Permissive
Does anyone know how to make selinux permissive without any app,I tried to change ro.build.selinux and set it to 0 but it didn't work...does anyone know what to edit in ramdisk to make selinux permissive.?
Traace said:
Tried to port this, Device reboots right after vendor logo
I compare stock Ramdisk with CM12. There are no diff. At end both have same values. I changed Kernel and Kernel Header
I changed the updater script so it fits to my partition. It gave me strange errors:
Also @michfood's tool just ain't work here, i took the v4 for my x64 win8.1. The Program is unable to extract the Ramdisk path, so i was forced to use "MTK Firmware Adapter Tool"
Recovery:TWRP 2.8.1.0
SoC:MT6592
Device: Doogee DG550
Click to expand...
Click to collapse
I'm still struggling to port this rom to DG550.
1. The tool you used to extract the kernel does not work in Windows 8.1 and Windows 10 (I got empty RAMDISK folder). So I switched back to Windows 7 and it worked well.
2. Compared both Ramdisk folders in Stock DG550 Kitkat and Stock Kingzone K1 Kitkat boot.img's.
There is no difference except in ueventd.rc file. I tried to mix DG550 kernel and Kingzone Z1 stock Ramdisk with DG550 Kitkat rom. It didn't boot at first. The problem was in ueventd.rc file. See line 152 (Mali Node). After replacing ueventd.rc file from DG550 ramdisk it booted and worked well (stock kitkat rom). So both the stock ramdisks are identical if ueventd.rc file is replaced.
3. But it fails when porting the boot.img for CM12.1. Theoretically CM12.1 ramdisk should work with DG550 kernel for CM12.1 rom without any changes (except ueventd.mt6592.rc). It does not pass the boot logo.
4. Also I noticed that there's some issue in sbin folder in ramdisk.
ADev_28 said:
Does anyone know how to make selinux permissive without any app,I tried to change ro.build.selinux and set it to 0 but it didn't work...does anyone know what to edit in ramdisk to make selinux permissive.?
Click to expand...
Click to collapse
/system/bin/setenforce 0
From any root terminal.
Thanks,
1. But i did port for mtk6582 (camera unfortunelty has stop)
chanaka89 said:
I'm still struggling to port this rom to DG550.
1. The tool you used to extract the kernel does not work in Windows 8.1 and Windows 10 (I got empty RAMDISK folder). So I switched back to Windows 7 and it worked well.
2. Compared both Ramdisk folders in Stock DG550 Kitkat and Stock Kingzone K1 Kitkat boot.img's.
There is no difference except in ueventd.rc file. I tried to mix DG550 kernel and Kingzone Z1 stock Ramdisk with DG550 Kitkat rom. It didn't boot at first. The problem was in ueventd.rc file. See line 152 (Mali Node). After replacing ueventd.rc file from DG550 ramdisk it booted and worked well (stock kitkat rom). So both the stock ramdisks are identical if ueventd.rc file is replaced.
3. But it fails when porting the boot.img for CM12.1. Theoretically CM12.1 ramdisk should work with DG550 kernel for CM12.1 rom without any changes (except ueventd.mt6592.rc). It does not pass the boot logo.
4. Also I noticed that there's some issue in sbin folder in ramdisk.
Click to expand...
Click to collapse
Please let us know if u can let it boot
Ramdisk sBin shoudn't be a problem, if they really cause trouble, try copy the missing files from base dg550 kk to cm12
[email protected] said:
1.
Click to expand...
Click to collapse
Thank you very much... Your guide was very appreciated... Work like a charm..
I used the device MT6592 - BLU VIVO IV of the my friend for port CM12.1
Sent from my LIFE PLAY X KK using XDA Free mobile app
lopestom said:
Thank you very much... Your guide was very appreciated... Work like a charm..
I used the device MT6592 - BLU VIVO IV of the my friend for port CM12.1
Sent from my LIFE PLAY X KK using XDA Free mobile app
Click to expand...
Click to collapse
congo
Traace said:
Please let us know if u can let it boot
Ramdisk sBin shoudn't be a problem, if they really cause trouble, try copy the missing files from base dg550 kk to cm12
Click to expand...
Click to collapse
mirrr46 said:
1. But i did port for mtk6582 (camera unfortunelty has stop)
Click to expand...
Click to collapse
seems storage bug...u need to fix storage .............check guide and comments
chanaka89 said:
I'm still struggling to port this rom to DG550.
1. The tool you used to extract the kernel does not work in Windows 8.1 and Windows 10 (I got empty RAMDISK folder). So I switched back to Windows 7 and it worked well.
2. Compared both Ramdisk folders in Stock DG550 Kitkat and Stock Kingzone K1 Kitkat boot.img's.
There is no difference except in ueventd.rc file. I tried to mix DG550 kernel and Kingzone Z1 stock Ramdisk with DG550 Kitkat rom. It didn't boot at first. The problem was in ueventd.rc file. See line 152 (Mali Node). After replacing ueventd.rc file from DG550 ramdisk it booted and worked well (stock kitkat rom). So both the stock ramdisks are identical if ueventd.rc file is replaced.
3. But it fails when porting the boot.img for CM12.1. Theoretically CM12.1 ramdisk should work with DG550 kernel for CM12.1 rom without any changes (except ueventd.mt6592.rc). It does not pass the boot logo.
4. Also I noticed that there's some issue in sbin folder in ramdisk.
Click to expand...
Click to collapse
i don't think so....again try and don't touch ramdisk
[email protected] said:
congo
seems storage bug...u need to fix storage .............check guide and comments
i don't think so....again try and don't touch ramdisk
Click to expand...
Click to collapse
How to solve storage bug??
Device booted.Not able to mount/access storage. ??

Blank screen in offline charge with any GSI ROM on Alcatel 5059D

Hello, to get started, I have an Alcatel 1x 5059D (ARM-A-Only) MT6739 processor. The problem is: when I use any GSI ROM (8.1 / 9.0 / 10 / 11 not tested) and try to charge the phone while it is completely turned OFF, it shows the battery % and the icon (like a normal phone would do) but insted of turning off the display, the phone stays on a blank screen after few seconds. If I press the power button again, the phone shows again the % and icon but again another blank screen. (Example if I wasn't clear enough: Power options menu => Turn OFF the phone completely => Charge the phone => Phone turns on and 1st: shows the Alcatel brand, 2nd: shows the battery icon and %, 3rd: blank screen). I modded the boot.img to make the offline charge work on a GSI ROM but I am probably doing something wrong to make this happen. I will attach the boot.img with the mod, the mods and the original boot.bin file (I took the mods from 4pda). To apply I used Carliv+Image+Kitchen+Windows+v1.3, replaced the init.rc and init.usb.rc and pasted the sbin and res folders in the ramdisk folder.

Categories

Resources