Database Info

Spreadtrum SC8810 MT6515 dead (urgent solution needed)

I rooted it which was absolutely fine but I tried to flash a custom rom onto it. I'm not going to lie I had no idea what this involved, what the risks were there , even I flashed it.
Anyway during the installation of the new Rom seemed to be going fine with Research Download and after finish installing it was just died. Since then i cannot get it to turn on and it just doesn't power up. It also won't charge now.
also when plugged into the PC it does not detected , so I'm hoping the fact it's still recognized as something means there may be some hope left.
plzzzz friends tell me what i do,
I have no idea what I'm doing, I am just here with my lovely new phone not turning on.
some persons have given idea of doing heating of the Processor IC / Processor Chip because of Boot failure , but how i do this process.
help me friends now.
Thanx in advance

I am having same problem here. I have intex aqua young sc8810 chip in phone. I tried to flash but it stuck at userdata for few seconds then it shown error while flashing now phone is totally dead not charging nor detect by USB or anything else.

[Q] MTK preloader port is gone!!! Replaced by MTK USB Port.?

Hello there!
So here goes my problem: The thing I was trying to do> Flashing a random rom in my MTK6582 device. Why random? Because I was unable to find my official ROM on internet. I thought if I flash any random ROM having MTK6582 device, It would work, which resulted in my current despo situation. No boot, No Logo, Nothing. The thing that triggered this was none other than "FORMAT" button from SP FLash Tool. Yup. Beforehand, I could at least enter in Bootloop and Recovery Mode. So is there anything which could be done except changing motherboard or force booting with JIG. As I said, it still shows "MTK USB Port" when I connect my phone w/o battery, however, Preloader is no longer appears. One more thing, it's not disappearing after 2 seconds as it did with preloader. Please, save my bud!!!
Device Name: Qmobile Linq X70, MTK6582, ARMv7 Quad Core 1.3GHz, KitKat 4.4.2

deoryus said:
Hello there!
So here goes my problem: The thing I was trying to do> Flashing a random rom in my MTK6582 device. Why random? Because I was unable to find my official ROM on internet. I thought if I flash any random ROM having MTK6582 device, It would work, which resulted in my current despo situation. No boot, No Logo, Nothing. The thing that triggered this was none other than "FORMAT" button from SP FLash Tool. Yup. Beforehand, I could at least enter in Bootloop and Recovery Mode. So is there anything which could be done except changing motherboard or force booting with JIG. As I said, it still shows "MTK USB Port" when I connect my phone w/o battery, however, Preloader is no longer appears. One more thing, it's not disappearing after 2 seconds as it did with preloader. Please, save my bud!!!
Device Name: Qmobile Linq X70, MTK6582, ARMv7 Quad Core 1.3GHz, KitKat 4.4.2
Click to expand...
Click to collapse
Actually, your shouldn't have done it, since as far as I have searched, I didn't find any Flashable stock ROM for your phone.
Flashing some other device's ROM will never work, since the mount points will be completely different even if you flash ROM of same chipset.
The only solution for this is waiting for someone to post flashable stock ROM for your phone, or finding someone who has the same phone and asking them to dump the ROM completely and give it to you, or the best way: Go to Service Center

Try flashing any flashable custom/stock rom if available for your device, and if not then u can use it as paperweight. And service center might not able to help as ur preloader is corrupted.

GokulNC said:
Actually, your shouldn't have done it, since as far as I have searched, I didn't find any Flashable stock ROM for your phone.
Flashing some other device's ROM will never work, since the mount points will be completely different even if you flash ROM of same chipset.
The only solution for this is waiting for someone to post flashable stock ROM for your phone, or finding someone who has the same phone and asking them to dump the ROM completely and give it to you, or the best way: Go to Service Center
Click to expand...
Click to collapse
Well, my uncle have same phone. Is it possible to extract a flashable ROM from his device?

deoryus said:
Well, my uncle have same phone. Is it possible to extract a flashable ROM from his device?
Click to expand...
Click to collapse
Yes, you can.
This will help: http://www.theandroidhow.com/2014/05/how-to-backup-rom-dump-mtk-android.html
It's quite difficult for a beginner.
Going to Service Center is the best way as I said.
Don't brick your uncle's phone too trying to save yours.
The choice is yours now

[Completed] Alcatel alcatel one touch flash plus boot loop. Cannot access recovery!

Hello,
Everyone is highly recommended to post their opinions and straight ideas on how can i fix my Alcatel alcatel one touch flash plus boot loop. It was originally a 4.4.4 kitkat by default and due to my curiosity to change my rom, I downloaded a customed rom lolipop 5.1.1 that i think might be compatible for my device but after installing the rom, I am now stock in boot loop. I have tried all the solution i knew from key combination power button plus up and power button plus down but unfortunately i cant access the recovery mode. The logo is blinking every 20 seconds. I also tried to connect it to my computer to install another rom but unfortunately my computer cannot recognize my phone. I already install the drivers necessary but i think the loop is the reason why my phone cant be detected. I have already search everything and every article point me to this site. According to my analysis, My phone is bricked!
The following are its conditions:
-Boot Loop every 20 seconds
-Cant access recovery mode by combination keys
-My PC cant recognize it when connected via its usb cable
-Sometimes when the logo disappears after 20 seconds, my pc suddenly beeps and its the signal for the recognition of the device but when the logo starts again, beep sounds again stating unrecognized device.
My Unit is Alcatel One Touch Flash Plus Display: 5.5" HD IPS capacitive touch screen
Operating System: Android 4.4 KitKat
Processor: Octa-core 1.5GHz
Memory (RAM l ROM): 2GB l 16GB
Can you help me.
Thank you!

Nordxxx said:
Hello,
Everyone is highly recommended to post their opinions and straight ideas on how can i fix my Alcatel alcatel one touch flash plus boot loop. It was originally a 4.4.4 kitkat by default and due to my curiosity to change my rom, I downloaded a customed rom lolipop 5.1.1 that i think might be compatible for my device but after installing the rom, I am now stock in boot loop. I have tried all the solution i knew from key combination power button plus up and power button plus down but unfortunately i cant access the recovery mode. The logo is blinking every 20 seconds. I also tried to connect it to my computer to install another rom but unfortunately my computer cannot recognize my phone. I already install the drivers necessary but i think the loop is the reason why my phone cant be detected. I have already search everything and every article point me to this site. According to my analysis, My phone is bricked!
The following are its conditions:
-Boot Loop every 20 seconds
-Cant access recovery mode by combination keys
-My PC cant recognize it when connected via its usb cable
-Sometimes when the logo disappears after 20 seconds, my pc suddenly beeps and its the signal for the recognition of the device but when the logo starts again, beep sounds again stating unrecognized device.
My Unit is Alcatel One Touch Flash Plus Display: 5.5" HD IPS capacitive touch screen
Operating System: Android 4.4 KitKat
Processor: Octa-core 1.5GHz
Memory (RAM l ROM): 2GB l 16GB
Can you help me.
Thank you!
Click to expand...
Click to collapse
Greetings and welcome to assist. Unfortunately I can not find any information on your device only other Alcatel one touch models so I am pretty sure you have installed an incompatible rom. The only thing I can suggest is ask your question here
http://forum.xda-developers.com/android/help
Hopefully someone with your device can help
Good Luck
Sawdoctor

[OPPO R7S] Hard-Bricked - Kindly Help Needed

Hi guys, i'm desperately writing this thread after asking for help in the Oppo Community forum without no luck.
I know that this is for R7 Plus but i hope that someone could help me with my beloved R7s.
Months ago i've succefully installed the Project Spectrum ROM and it worked fine until few weeks ago when i noticed a random system slow down, maybe after an automatic app update.
I tryed to uninstall few apps and reboot the phone several times but with no luck.
So i decided to wipe it and reinstall the Color OS following the walkthrough but something went wrong and now my OPPO R7s is in a strange bootloop without recovery and fastboot.
The strange things are these:
- if I press the power button all I can see is the OPPO Logo and the loading dots in slow-mo
- if i connect it directly to a Windows PC it is recognized as a generic "Android" terminal.
- if i connect it to a Windows PC pressing and holding POWER + VOLUME DOWN + VOLUME UP it's recognized as a QHSUSB_BULK
I'm not a noob, neither an engineer, but i've a bit of familiarity with computers and similar things so i've tried to follow this guide:
http://community.oppo.com/en/forum.php?mod=viewthread&tid=48654
Downloading this service repair rom : https://drive.google.com/file/d/0BybDE_sPI3b5cmgtU05fbXNobVU/view (from this related discussion : http://forum.xda-developers.com/r7-plus/help/r7s-service-romqpst-unbrick-t3493377)
Following the guide, when i try to execute MSM8x39Downloadtool.exe selecting the phone model (i've three choices xx080_32G, xx081_32G, xx082_32G - and i don't know which one is the correct one) the phone is not recognized as COM CONNECTED in none of the ports. If I also do the verification, clicking on the top right button, it shows FAILED on system.img file.
Can that be the problem?
I'm stuck guys and i don't know what to do.
Any help will be better then a christmas present
Thanks in advance!!
A.

Download this rom and place it in the internal sd and flash to downgrade from spectrum
https://s3.amazonaws.com/public.opp...d_ColorOS/Specified_ColorOS_R7sf_full_009.zip

kishd said:
Download this rom and place it in the internal sd and flash to downgrade from spectrum
https://s3.amazonaws.com/public.opp...d_ColorOS/Specified_ColorOS_R7sf_full_009.zip
Click to expand...
Click to collapse
Thanks kishd i'll give this a try!
The only thing i'm bit worried about is how to flash from the internal sd without recovery mode and fastboot...
I'll keep you updated!:good:

any news?did you manage to fix?

hello guys
i have a problem with my oppo RS7
it has a hard bricked and stucked on booting and booting..... I only have a MacBook Pro and not windows
is anyone over there that knows exactly how to unbrick it using a Mac ?!

[Completed] Hard Bricked in a peculiar manner

Hi xda,
So I had a soft bricked Micromax Canvas a290 which boot looped and couldnt access recovery. I flashed it with a stock ROM. Now the phone is hard bricked, and I'm thinking probably because the rom I downloaded had issues. I looked up another stock rom from xdafirmware, and am trying to follow a tutorial on youtube on flashing a hard bricked device.
The issue I have here is this:
The tutorial says the phone is supposed to connect and disconnect every 7-8 seconds (evident by the sound windows makes when usb device is connected and disconnected).
The thing is, when I connect my device windows makes the connected sound, but the device doesnt disonnect. SP flash tool cant flash my phone. I have tried any and every button combination, but they dont seem to help.
I am an tech enthusiast myself, and I have flashed a lot of mtk soft bricked devices before, but I am totally stumped here.
Can anyone help?? Any ideas whats happening? Any help is greatly appreciated. Thank you.

Tiks_Baralous said:
Hi xda,
So I had a soft bricked Micromax Canvas a290 which boot looped and couldnt access recovery. I flashed it with a stock ROM. Now the phone is hard bricked, and I'm thinking probably because the rom I downloaded had issues. I looked up another stock rom from xdafirmware, and am trying to follow a tutorial on youtube on flashing a hard bricked device.
The issue I have here is this:
The tutorial says the phone is supposed to connect and disconnect every 7-8 seconds (evident by the sound windows makes when usb device is connected and disconnected).
The thing is, when I connect my device windows makes the connected sound, but the device doesnt disonnect. SP flash tool cant flash my phone. I have tried any and every button combination, but they dont seem to help.
I am an tech enthusiast myself, and I have flashed a lot of mtk soft bricked devices before, but I am totally stumped here.
Can anyone help?? Any ideas whats happening? Any help is greatly appreciated. Thank you.
Click to expand...
Click to collapse
Greetings and welcome to assist. I can find very little information for your device apart from this thread which may help, can you connect to the device just using fastboot ?
https://forum.xda-developers.com/android/general/tutorial-micromax-canvas-knight-a290-t2872896
Good Luck
Sawdoctor