Database Info

[Q] Help! Can not boot

Hello,
I have big problem. I tried to upgrade to lollipop version, used it for one hour and then decided to get back to kitkat. For the procedure I used some tool from killerdogKD which name is MT7-L09 Unbrick (it is a fastboot). The procedure went, phone rebooted and got stuck in boot loop (only logo is showed for few seconds). Now I can only get in fastboot and rescue mode. I've tried to flash stock rom, but without success. Any suggestions? PS. Yes, I now I am jackass and sorry for my bad English:angel:

Stock recovery installed (extracted from official KK ROM)??? 3 button procedure already tried?

Will not work. Are there no going back. He can recover only 5.1.
For the people hanging in Bootllop because they have the 4.4.X Recovery flashed.
Load zip, go to the boot loader and the two flash imgs.
command:
fastboot flash boot boot.img
fastboot flash recovery recovery.img
If both of the 5.1.
https://mega.co.nz/#!DNw13JhK!7ATC9p...G50saLGZG3vKzM
KK is not possible 5.1, just with dload the flash 5.1 again. Is indeed just about the one that has 5.1 Recovery again.
Here read next time.
http://forum.xda-developers.com/mate-7/general/mate-7-update-to-lollipop-screenshots-t3125227/page28

I have the same problem and probably caused by same thing. But I can' even enter bootloader. When phone was bootlooping, I turned it off. Then I tried to get into recovery (by holding power + volume down), but phone always shut down after Huawei logo appears (shut down with short vibration).
It does not matter when I release the buttons, I also tried the recovery (vol up + power) or the force update mode (vol up + vol down + power).
Is there any solution to this? I really hope so...

Look at my post and Liks.

Thank you Fooox1 for trying to help, but the problem is, that I can't even enter the bootloader (and your steps require that). I think that international Mate7 have different key combination for entering bootloader? Check also this: http://forum.xda-developers.com/mate-7/help/fastboot-mode-t3086531
It is true that even before I was not able to get into bootloader with vol down + power, so maybe there is just different key combination or it is not possible at all...
I think I will try to write to Huawei support.

In the bootloader you come when the power is off and you Vol - holding down, then to the PC. To turn it off properly you must Vol - and Power button until it vibrates.
Key combination is the same for all.

I know, that is what I am doing it. And I already did it with many other phones successfully, so its not like this is my first time.
I am holding down power + vol down
Phone vibrates, I am still holding both buttons
Huawei logo appears, I am releasing power button, but still holding vol down button
Phone vibrates and turn off
I also tried to release power button when phone vibrates, or not release both buttons at all or I don't know what else. Tried 100x times.
I will try to contact Huawei, maybe it is known issue. It should really be same key combinations for all devices.
Thank you.

The Mate mus but this depend on the USB, otherwise it does not come into the bootloader.

Whoa! I did it. Yes, it was connected in USB, but in quickcharge USB. I tried different one and I am in!
For some reason, it did not like the quickcharge USB port, strange.
@Fooox1: but thank you, with your last comment I got the idea to try different USB

Well, I am little bit furhter, but still not working unfortunately. I got into bootloader, I flashed the boot and recovery. Then I was trying to three buttons force update and it is still failing.
I have Update.zip in dload folder on sd card, but update is failing immediatelly...

So now, I started the three buttons update while connected to computer via USB and it is actually doing something. But it is too soon to say if it helped (43%).

can't boot too
I need your help Guy's
My Mate 7 did not start after i rooted the lollipop rom with kingroot. I tried to put back the 5.1 boot.img and the recovery.img. After that i tried to flash the ota 5.1 rom agian with the 3 bottons mode. The phone startet the Update but it get stocked by 90%. I waited ca. 10 min after i just rebooted the phone. Now the Phone starts with the Huawei Ascend sign two times and after that i am in recovery mode. I don't know what i can do now! Can anyone help me please?

Yes, I have the same problem

driver84 said:
I need your help Guy's
My Mate 7 did not start after i rooted the lollipop rom with kingroot. I tried to put back the 5.1 boot.img and the recovery.img. After that i tried to flash the ota 5.1 rom agian with the 3 bottons mode. The phone startet the Update but it get stocked by 90%. I waited ca. 10 min after i just rebooted the phone. Now the Phone starts with the Huawei Ascend sign two times and after that i am in recovery mode. I don't know what i can do now! Can anyone help me please?
Click to expand...
Click to collapse
Same here! Help!
must we send in warranty?

So it seems to me, that problem is Huawei. Once, they are using Update.APP and later Update.ZIP, not sure why.
- recovery from 5.1 is working, but it is expectin Update.APP, but 5.1 update is in Update.ZIP, so it fails immediately (with error Update.APP not found). Yes, when you connect to phone to computer, it seems that it is doing something and it will get to 90%. But it is actually doing nothing, you can even pull out the sd card and it is the same. I think it is waiting for some action from computer, but not sure which (I also tried to install HiSuite and do something with it, but no success).
- recovery from update B137 will accept Update.ZIP, but when you try to flash it you won't be able to get in it, it is not working (I also tried B127).
So now, we either need recovery, which will work on 5.1 and will accept Update.ZIP or we need update packed as Update.APP (and yes, I tried to rename it etc.). So actually, our phones are pretty ok, we can get in recovery etc., but Huawei is messing with this different formats for some reason
@Fooox1: Do you have any ideas? Maybe you have another bootloader / recovery image? How did you got the 5.1? Thank you...
Edit: maybe the problem is, that we are trying to run the update OTA (Update.ZIP) instead of full rom (Update.APP)? Is this how it is divided, Update.ZIP is just incremental update, while Update.APP is full rom? If that is the case, we will need the full rom, maybe Huawei can release it?

I have not the problem, but users in our forum. I have the boat and recovery.img from the update unzip, a user has then flashed via fastboot and sin device was running again. For him only recovery was gone after he has the Kang Recovery flashed. The Update.zip he did not need to flash.
Other users have only the boot and recovery.img flashed and then the not unpacked update.zip in a folder (dload) on the SD and these then flashed three fingers method. What also has to work.
Here is still the boat and recovery.img of 5.1.
https://mega.co.nz/#!DNw13JhK!7ATC9pAUID0VyX5N3pQwQLbb_VyuOG50saLGZG3vKzM
And update.zip
https://mega.co.nz/#!vdYlxQIA!P34e3RI-hQT1ZY2WnfOosGmkq2wlr6NViq6ehQuWN5k

I think it may help if somebody will create *.img files from Lollipop, then we might be able to flash it via fastboot (the same as it is in this MT7-L09 Unbrick). I think we will need:
boot.img - ok
cache.img
cust.img
recovery.img - ok
system.img
userdata.img

Can make you yourself. Unzip, when present therein Update.app the extension .app in change .zip and unpack. Now you have another Update.app, this you can unpack the Huaweiextraktor, you've got your files. However, it does not contain all IMGs.
You could try but the resulting Update.app to pack in the dload folder and flash. If so, then the original and encrypted.

Hallo again,
i just called the Huawei Service Center in Germany. They openend up a Ticket for me. They told me to make a factory reset and after that the Phone should boot normaly. I did that, but still the same is happening. The shows the Huawei Ascend Logo 2 times and after that i am in recovery mode again.
The only thing i can do next, is to send the phone to the Huawei Service Center and hopefully i will get it back in 7 Days.

Cannot install TWRP over Huawei eRecovery??

I am unable to install TWRP over the huawei eRecovery.
>I first unlocked the bootloader by using fastboot OEM command
>then installed TWRP. Tried all the versions that i found for mate 8. I get a message "OKAY"
> Then I get a message saying that I have to press the up vol button to go to recovery. And when I try to go to the recovery window I see Huwaei's recovery and not TWRP. I cant use TWRP manager for this as it will not work until I have rooted my phone. SuperSu through playstore does not work. How will I proceed with rooting and installing TWRP. I am stuck !!
Is there any application like ODIN for huawei? That always worked, no matter what went wrong. Please help!!!!!!
I guess I am using the international version

ure going about this all wrong mate
as already explained in the other thread, u cant enter twrp that way. if u press power up in the start screen ull always end up in the erecovery, no matter which regular recovery u have flashed.
easiest way to enter regular recovery is to install flashify from the playstore and choose to reboot phone into recovery
Sent from my Huawei Mate 8 NXT-AL10 using Tapatalk

cheth20 said:
I am unable to install TWRP over the huawei eRecovery.
>I first unlocked the bootloader by using fastboot OEM command
>then installed TWRP. Tried all the versions that i found for mate 8. I get a message "OKAY"
> Then I get a message saying that I have to press the up vol button to go to recovery. And when I try to go to the recovery window I see Huwaei's recovery and not TWRP. I cant use TWRP manager for this as it will not work until I have rooted my phone. SuperSu through playstore does not work. How will I proceed with rooting and installing TWRP. I am stuck !!
Is there any application like ODIN for huawei? That always worked, no matter what went wrong. Please help!!!!!!
I guess I am using the international version
Click to expand...
Click to collapse
When the phone is off, hold on the volume + & power button at the same time. When the screen flashes on, quickly remove your fingers from the said key presses and it should boot into twrp. If you hold them too long it will boot into erecovery. If you want to reboot into twrp recovery when the phone is already on, then you will have to get an app like quick reboot or flash a Rom which has that option.
Sent from my NEXT using Tapatalk

tdamocles said:
When the phone is off, hold on the volume + & power button at the same time. When the screen flashes on, quickly remove your fingers from the said key presses and it should boot into twrp.
Click to expand...
Click to collapse
This.
Power plus volume down does nothing, TWRP-wise. However that is whta's being said to press in 99% of the threads/tutorials.
Took me HOURS and countless re-flashing of TWRP to figure this out myself. (the up *plus* down thingy). Really annoying.

tdamocles said:
When the phone is off, hold on the volume + & power button at the same time. When the screen flashes on, quickly remove your fingers from the said key presses and it should boot into twrp. If you hold them too long it will boot into erecovery. If you want to reboot into twrp recovery when the phone is already on, then you will have to get an app like quick reboot or flash a Rom which has that option.
Sent from my NEXT using Tapatalk
Click to expand...
Click to collapse
Thanks a ton! this worked

cheth20 said:
I am unable to install TWRP over the huawei eRecovery.
>I first unlocked the bootloader by using fastboot OEM command
>then installed TWRP. Tried all the versions that i found for mate 8. I get a message "OKAY"
> Then I get a message saying that I have to press the up vol button to go to recovery. And when I try to go to the recovery window I see Huwaei's recovery and not TWRP. I cant use TWRP manager for this as it will not work until I have rooted my phone. SuperSu through playstore does not work. How will I proceed with rooting and installing TWRP. I am stuck !!
Is there any application like ODIN for huawei? That always worked, no matter what went wrong. Please help!!!!!!
I guess I am using the international version
Click to expand...
Click to collapse
Well, I have a question. What is the eRecovery, because I've seen this screen also and I dont know what it does. Also, there are three options in it: download latest version and recovery, reboot and shutdown. So if I press download latest version and recovery what will happen? Because I'm actually looking for a way to get off TWRP without having to lose any data (I want to install the latest OTA, but I've seen that TWRP doesn't support well those, and I don't want to mess up my phone)...
Please help!

easy: download a stock rom identical to your current version, extract recovery partition using the huawei app extractor from the rom's update.app file and then flash that through fastboot
and since u probably have no idea what im talking about, i suggest u use google and xda search functions before asking any further questions here dont be lazy and expect everyone to work for you and serve everything on a silver platter, do your due diligence!
Sent from my Huawei Mate 8 NXT-AL10

Hi, simply press Volume up an down at same time when device is powering up...and hold it, until Twrp logo is on the screen. Works always for me.
Greets Tobias

OMGiidiness
Guys, volume-up+power goes to recovery
Volume-down+power goes to fastboot or bootloader

bluheart said:
OMGiidiness
Guys, volume-up+power goes to recovery
Volume-down+power goes to fastboot or bootloader
Click to expand...
Click to collapse
And just for the complete list:
Volume up + power AND USB plugged in goes into eRecovery (or TWRP, if you flashed TWRP to RECOVERY2 instead to RECOVERY)
Volume up and down + power and USB plugged in forces update via USB (indicated by a little USB-like icon in the recovery circle. The progess bar goes to 5% and waits for input from your PC)

True, when usb is attached

tdamocles said:
When the phone is off, hold on the volume + & power button at the same time. When the screen flashes on, quickly remove your fingers from the said key presses and it should boot into twrp. If you hold them too long it will boot into erecovery. If you want to reboot into twrp recovery when the phone is already on, then you will have to get an app like quick reboot or flash a Rom which has that option.
Click to expand...
Click to collapse
I can attest to this, i flashed twrp many times thinking it was not working beacause i am used to the mate 7 holding volume up + power long enough boots into recovery (twrp) but this won't work on mate 8

sibiyav1486 said:
I can attest to this, i flashed twrp many times thinking it was not working beacause i am used to the mate 7 holding volume up + power long enough boots into recovery (twrp) but this won't work on mate 8
Click to expand...
Click to collapse
Works just fine.

Work like a charm
cheth20 said:
Thanks a ton! this worked
Click to expand...
Click to collapse
Work like a charm ...

Same to me
I see same this problem from my Honor 6X Pakistani version

installed twrp in my ,honor 5c,,,but cant get to the recovery,,tried every version of u tip,guys,,,what to do,,,,?

I have same problem, in theory i have TWRP as recovery but when star entry in eRecovery .... help

tdamocles said:
When the phone is off, hold on the volume + & power button at the same time. When the screen flashes on, quickly remove your fingers from the said key presses and it should boot into twrp. If you hold them too long it will boot into erecovery. If you want to reboot into twrp recovery when the phone is already on, then you will have to get an app like quick reboot or flash a Rom which has that option.
Sent from my NEXT using Tapatalk
Click to expand...
Click to collapse
Thanks mate it worked out perfectly.

to come to twrp hold on the volume+ and volume- works on mine P10

[SOLVED] H60-L02 bricked beyond recovery? Plz help me!

edit: If you are just looking for the solution, plz click here: http://forum.xda-developers.com/showpost.php?p=68626049&postcount=11
Hey there,
first of all I want to say Thank You for this great community and the work at XDA. Awesome. :good:
I bricked my Honor 6 H60-L02 and I am lost to bring it back to life. :crying:
Where it started:
I was using the official ROM from this thread [OFFICIAL] Honor 6 (L02, L12, L04) Stock ROMs. To be more specific it was the latest Android 6.0 EMUI 4.0 B823 that I installed with all the different OTA-Files starting with the original 5.1 ROM B535. The Honor was rooted and also the bootloader is still unlocked (I already checked the status via Fastboot.).
After I while the Honor 6 started to crash sometimes and the headphone-buttons didn't worked anymore. Then a few days ago the phone crashed and I was not able to boot it again.
And so I tried this:
Using the Rollback-Zip to go back to 5.1. But the 3btn-method didn't worked. The phone didn't want to boot into the recovery. Also the Vol+ and Power-Button didn't work to start the Recovery of the phone. Result: Bootloop.
So I installed ADB and Fastboot (with all necessary drivers) and tried to flash the phone with the 5.1 B535 (as mentioned in Honor 6 H60-L02 Hard Bricked - Only access to fastboot (Vol+ and Usb PC)) because there isn't a 6.0 B823 ROM available. I was able to flash boot, recovery, cust, system, userdata and another one I forgot right now. But the result was the same: Bootloop and no 3-btn or recovery via Vol+ and Power-Button. I also tried to flash it with the HonorTool. Same result.
Then I tried to flash different TWRP versions as recovery. Result: The same as above.
So I tried another official ROM 5.1 B526 because someone had the same problem and was able to recover his phone with this ROM (another thread in the forum). But that didn't worked ether.
Then I tried to flash all the img-files of the 5.1. B535 as crc, ptable and so on because I thought that there could be the problem. But when I tried e.g. to flash crc I get the error FAILED: command not allowed. So I tried to unlock the phones partition via Fastboot and fastboot flashine unlock_critical. But using the command unlock_critical gives me also the Failed error. So I was lost again.
Status right now:
I'm still able to boot into the bootloader via Vol- and Power. But right now the phone was running out of battery. Means I see the red battery symbol when I try to start the phone via the power button (without connecting to the PC or charger) but it isn't booting even into the bootloop. The red battery symbol pops up for a second and the screen went black again.
When I use the charger then the symbol changes to a green battery and stays there, but not the moving one that indicates that the phone is charging. When I use the Power button with usb-charger connected to start the phone I'm trapped in the bootloop again.
You see I already tried a lot of different things I could find on the forum. But nothing worked for me.
I know that it was a fault to try to install 5.1 B535 without the rollback, but I wasn't able to rollback as mentioned under point 1.
Maybe anyone could give me a hint and help me to bring my phone back to life.
Thx a lot! I appreciate that al lot!
If you need anymore informations, plz let me know.
Greets, mike175de
P.S: Sorry for my school english. It is a little bit rusty ;o)

mike175de said:
Hey there,
first of all I want to say Thank You for this great community and the work at XDA. Awesome. :good:
I bricked my Honor 6 H60-L02 and I am lost to bring it back to life. :crying:
Where it started:
I was using the official ROM from this thread [OFFICIAL] Honor 6 (L02, L12, L04) Stock ROMs. To be more specific it was the latest Android 6.0 EMUI 4.0 B823 that I installed with all the different OTA-Files starting with the original 5.1 ROM B535. The Honor was rooted and also the bootloader is still unlocked (I already checked the status via Fastboot.).
After I while the Honor 6 started to crash sometimes and the headphone-buttons didn't worked anymore. Then a few days ago the phone crashed and I was not able to boot it again.
And so I tried this:
Using the Rollback-Zip to go back to 5.1. But the 3btn-method didn't worked. The phone didn't want to boot into the recovery. Also the Vol+ and Power-Button didn't work to start the Recovery of the phone. Result: Bootloop.
So I installed ADB and Fastboot (with all necessary drivers) and tried to flash the phone with the 5.1 B535 (as mentioned in Honor 6 H60-L02 Hard Bricked - Only access to fastboot (Vol+ and Usb PC)) because there isn't a 6.0 B823 ROM available. I was able to flash boot, recovery, cust, system, userdata and another one I forgot right now. But the result was the same: Bootloop and no 3-btn or recovery via Vol+ and Power-Button. I also tried to flash it with the HonorTool. Same result.
Then I tried to flash different TWRP versions as recovery. Result: The same as above.
So I tried another official ROM 5.1 B526 because someone had the same problem and was able to recover his phone with this ROM (another thread in the forum). But that didn't worked ether.
Then I tried to flash all the img-files of the 5.1. B535 as crc, ptable and so on because I thought that there could be the problem. But when I tried e.g. to flash crc I get the error FAILED: command not allowed. So I tried to unlock the phones partition via Fastboot and fastboot flashine unlock_critical. But using the command unlock_critical gives me also the Failed error. So I was lost again.
Status right now:
I'm still able to boot into the bootloader via Vol- and Power. But right now the phone was running out of battery. Means I see the red battery symbol when I try to start the phone via the power button (without connecting to the PC or charger) but it isn't booting even into the bootloop. The red battery symbol pops up for a second and the screen went black again.
When I use the charger then the symbol changes to a green battery and stays there, but not the moving one that indicates that the phone is charging. When I use the Power button with usb-charger connected to start the phone I'm trapped in the bootloop again.
You see I already tried a lot of different things I could find on the forum. But nothing worked for me.
I know that it was a fault to try to install 5.1 B535 without the rollback, but I wasn't able to rollback as mentioned under point 1.
Maybe anyone could give me a hint and help me to bring my phone back to life.
Thx a lot! I appreciate that al lot!
If you need anymore informations, plz let me know.
Greets, mike175de
P.S: Sorry for my school english. It is a little bit rusty ;o)
Click to expand...
Click to collapse
Just flash boot, Cust, recovery and system images and let it boot normally. Don't do any button combo. I have had instances where it works. Give it a try.

With which version?
muradulislam said:
Just flash boot, Cust, recovery and system images and let it boot normally. Don't do any button combo. I have had instances where it works. Give it a try.
Click to expand...
Click to collapse
Thx for your reply.
With which version should I flash? B535 or B526? Should I only flash the three images boot, cust and system? Nothing else?
Thx for a reply!

mike175de said:
Thx for your reply.
With which version should I flash? B535 or B526? Should I only flash the three images boot, cust and system? Nothing else?
Thx for a reply!
Click to expand...
Click to collapse
You can use any firmware but the latest one should be better, and flash four images, boot, Cust, system and boot and let it boot normally.
Then put the dload folder with update.app in sd card and do an update from settings.

Thx. I will give it a try when I'm back from work.
I let you know if it is working.

mike175de said:
Thx. I will give it a try when I'm back from work.
I let you know if it is working.
Click to expand...
Click to collapse
I meant to say flash boot, Cust, recovery and system images.
Wrote boot twice

Nothing changed
Hey muradulislam,
Thx again.
I flashed the images (boot.img twice) but without success. Still the same error (with normal booting aka without any special button combination or with button combination). The honor boots and stays in the bootmode aka bootloop with the led blinkin red. And I still can't boot into recovery via Vol+ and Power..
Any other suggestions?
mike

mike175de said:
Hey muradulislam,
Thx again.
I flashed the images (boot.img twice) but without success. Still the same error (with normal booting aka without any special button combination or with button combination). The honor boots and stays in the bootmode aka bootloop with the led blinkin red. And I still can't boot into recovery via Vol+ and Power..
Any other suggestions?
mike
Click to expand...
Click to collapse
Of all the things you have already tried, the only thing remains to take it to a Huawei service center.
May be someone else can help you here but I have read most of honor 6 and 7 posts and I don't think there is anything there for this problem atm.

Hmm, thx. That is bad...
I bought this phone in China when I was there for work. And I suppose that the german service of Huwaei will not help me at all with this phone.
Does anybody else have any clue how to bring the phone back to life?
Thx a lot.

mike175de said:
Hmm, thx. That is bad...
I bought this phone in China when I was there for work. And I suppose that the german service of Huwaei will not help me at all with this phone.
Does anybody else have any clue how to bring the phone back to life?
Thx a lot.
Click to expand...
Click to collapse
I myself have an H60-L01, bought it from china, bricked and tried everything to revive it but could not, still have to try Huawei customer service in Pakistan, am not sure whether they will be able to help me or not, but will give it a try. I wish you luck buddy. Hope you find a solution.

It's alive ;o)
The phone is working again.
Here are the steps I did for everybody else confrontated with same problem:
1. Download your last working ROM or OTA-File: In my case the OTA-File OTA-EMUI 4.0_H60-L02-L12_B811_B823.zip from this Mega-Link:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!KwhlRKYR
2. Unzip the file and extract recovery.img and boot.img with the Huawei Update Extractor (http://forum.xda-developers.com/showthread.php?t=2433454).
3. Boot the phone into fastboot mode (connect the USB cable, press the power button to turn off and immediately press the volume down button).
4. Use fastboot to flash the two images of 2. If you need fatsboot you can find it here http://www.mediafire.com/download/o5ruw752ked884u/adb+H60.zip (Extract adb.zip and copy the extracted files from 2. in the folder adb. In the adb folder run cmd.exe as administrator.)
5. Use this commands for flashing:
fastboot devices => If the device is recognized correctly it is displaying a series of numbers
fastboot flash recovery RECOVERY.img
fastboot flash boot BOOT.img
fastboot reboot
6. Charge the phone with the Huawei charger, not via USB/PC! (50% is enough.)
7. Download in the meantime the Developer ROM H60_EMUI3.1_Android5.1_6.1.1.zip from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
8. Extract the zip file from 7. and copy UPDATE.app onto your SD-Card into /dload
9. Insert the SD without connecting.
9.1. Disconnect the USB cable from your PC or charger.
9.2. Press the Power button to turn off (maybe that is not necessary.)
9.3. When you feel the vibration press 3btn (Vol+ and Vol- and Power).
9.4. When the Honor logo appears connect your SD-Card (continue to press 3btn for 8 -10 more seconds) => Wait for the recovery process, it should start automatically.
10. After installation Android boots. Skip the first step installation (you should now have the 6.1.1. Developer-Edition installed). Rollback to Android 5.1.1 with the Rollback-File Rollback 591 EMUI3.0.zip from here:
http://www.mediafire.com/download/9qrd8zm9280gy5e/Rollback+591+EMUI3.0.zip
Do do so put the unzipped UPDATE.app from the Rollback-File onto your SD-Card and do a local update via the Update Manager.
11. Boot into Android again (it will still be the 6.1.1 Developer Edition). In my case I want to install the latest Android 5.1.1 B535 from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
I did it via local update again.
12.. After installation and booting => Voila here is your working Android 5.1.1 B535 again. Have fun
13. Brick it again with updating to Android 6.0
I hope I could help somebody with my experience to bring his/her phone back to life.
CU, mike

The same can not restore brick
Hello! In what condition I have a phone? My phone is loaded in error func_boot_kernel.

igorxxl said:
Hello! In what condition I have a phone? My phone is loaded in error func_boot_kernel.
Click to expand...
Click to collapse
Have you unlocked and rooted it?
When does it says that message?

error! no func. func_boot_kernel or _recovery
zinko_pt said:
Have you unlocked and rooted it?
When does it says that message?
Click to expand...
Click to collapse
The bootloader is unlocked. Root is. Phone is loaded into the error! no func. func_boot_kernel. If you try to enter into the recovery, the error! no func. func_boot_recovery.
The error is the same as here club.huawei.com/thread-7962289-1-1.html
I tried to put EMUI4.0, then the phone stopped working. Through ADB stitched, weighting system, boot, recovery, cust.img. It shows all ok. But then the error again. He tried to put different versions of TWRP. On the 3 button also does not work.
Thank you for your attention to my problem.

igorxxl said:
The bootloader is unlocked. Root is. Phone is loaded into the error! no func. func_boot_kernel. If you try to enter into the recovery, the error! no func. func_boot_recovery.
The error is the same as here club.huawei.com/thread-7962289-1-1.html
I tried to put EMUI4.0, then the phone stopped working. Through ADB stitched, weighting system, boot, recovery, cust.img. It shows all ok. But then the error again. He tried to put different versions of TWRP. On the 3 button also does not work.
Thank you for your attention to my problem.
Click to expand...
Click to collapse
You can't use 3 button with custom recovery and root. It wont work.
You need stock recovery in the same version as the rest of files used to flash other partitions.
Flash all stock partitions, then just boot the phone. Check if it works. Forget about TWRP and root for now. One thing at a time.

Nothing helps. I sew different versions via Fastboot. Everywhere all shows OK. However, when you restart the exact same mistake again ..

igorxxl said:
Nothing helps. I sew different versions via Fastboot. Everywhere all shows OK. However, when you restart the exact same mistake again ..
Click to expand...
Click to collapse
You can also try installing custom recovery and restore a twrp backup of ROM.

zinko_pt said:
You can't use 3 button with custom recovery and root. It wont work.
You need stock recovery in the same version as the rest of files used to flash other partitions.
Flash all stock partitions, then just boot the phone. Check if it works. Forget about TWRP and root for now. One thing at a time.
Click to expand...
Click to collapse
goldfinv said:
You can also try installing custom recovery and restore a twrp backup of ROM.
Click to expand...
Click to collapse

i'm in the same situation with my honor 6 plus pe-ul00 i'll try this metod!

mike175de said:
The phone is working again.
Here are the steps I did for everybody else confrontated with same problem:
1. Download your last working ROM or OTA-File: In my case the OTA-File OTA-EMUI 4.0_H60-L02-L12_B811_B823.zip from this Mega-Link:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!KwhlRKYR
2. Unzip the file and extract recovery.img and boot.img with the Huawei Update Extractor (http://forum.xda-developers.com/showthread.php?t=2433454).
3. Boot the phone into fastboot mode (connect the USB cable, press the power button to turn off and immediately press the volume down button).
4. Use fastboot to flash the two images of 2. If you need fatsboot you can find it here http://www.mediafire.com/download/o5ruw752ked884u/adb+H60.zip (Extract adb.zip and copy the extracted files from 2. in the folder adb. In the adb folder run cmd.exe as administrator.)
5. Use this commands for flashing:
fastboot devices => If the device is recognized correctly it is displaying a series of numbers
fastboot flash recovery RECOVERY.img
fastboot flash boot BOOT.img
fastboot reboot
6. Charge the phone with the Huawei charger, not via USB/PC! (50% is enough.)
7. Download in the meantime the Developer ROM H60_EMUI3.1_Android5.1_6.1.1.zip from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
8. Extract the zip file from 7. and copy UPDATE.app onto your SD-Card into /dload
9. Insert the SD without connecting.
9.1. Disconnect the USB cable from your PC or charger.
9.2. Press the Power button to turn off (maybe that is not necessary.)
9.3. When you feel the vibration press 3btn (Vol+ and Vol- and Power).
9.4. When the Honor logo appears connect your SD-Card (continue to press 3btn for 8 -10 more seconds) => Wait for the recovery process, it should start automatically.
10. After installation Android boots. Skip the first step installation (you should now have the 6.1.1. Developer-Edition installed). Rollback to Android 5.1.1 with the Rollback-File Rollback 591 EMUI3.0.zip from here:
http://www.mediafire.com/download/9qrd8zm9280gy5e/Rollback+591+EMUI3.0.zip
Do do so put the unzipped UPDATE.app from the Rollback-File onto your SD-Card and do a local update via the Update Manager.
11. Boot into Android again (it will still be the 6.1.1 Developer Edition). In my case I want to install the latest Android 5.1.1 B535 from here:
https://mega.nz/#F!ztYliaxL!4gfyXozSW51eNahGZBDgBQ!6w5inQ6Z
I did it via local update again.
12.. After installation and booting => Voila here is your working Android 5.1.1 B535 again. Have fun
13. Brick it again with updating to Android 6.0 [emoji14]
I hope I could help somebody with my experience to bring his/her phone back to life.
CU, mike
Click to expand...
Click to collapse
I got a problem at 9.3 or 9.4. The recovery wont start i see only honor logo i used PE_EMUI3.1_Android5.1_6.1.1.zip (as developer edition i.e sdcard/dload/UPDATE.APP) and PE-UL00-V100R001CHNC00B200.zip to extract and flash BOOT.img and RECOVERY.img
any ideas why i can't enter in recovery? =(
EDIT: "fixed with DC-Phoenix tool"

3btn dont work!!!

Hi, i need some help
At this time I have the honor totally clean, without any android system. I'm trying to install a rom and when I get to step 3 of the buttons does not work. It is the original logo of honor and not out there.
tks

Try this.
DigiGoon said:
Follow the below steps, and you'll get back to stock:
Download your phone's latest firmware and extract system.img, boot.img, recovery.img, cust.img from UPDATE.APP using Huawei Update Extractor tool.
Boot into bootloader mode by switching off the phone then pressing only the Vol DOWN button, and connecting it to PC simultaneously.
Flash recovery first, using this command.
Code:
fastboot flash recovery recovery.img
Flash all other extracted files similarly firing these commands.
Code:
fastboot flash boot boot.img
fastboot flash cust cust.img
fastboot flash system system.img
After doing this put that very UPDATE.APP from which you extracted the files in dload folder of your external SDCARD.
Switch off your phone, and press Vol UP + Vol DOWN + Power button simultaneously.
Your device will now get to the full stock firmware.
NOTE: If the manual flashing doesn't works or you get any errors, then first try only the force update method, i.e Putting the UPDATE.APP from which you extracted the files in dload folder of your external SDCARD and pressing Vol UP + Vol DOWN + Power button simultaneously after switching off your phone.
Click to expand...
Click to collapse

goldfinv said:
Try this.
Click to expand...
Click to collapse
Don`t work
The 3btn still does not work

b4co said:
Don`t work
The 3btn still does not work
Click to expand...
Click to collapse
What do you mean by does not work?
You can not start a forced update or forced update fails?
Is your bootloader unlocked or locked?
What were you using before the problem?
Firmware or custom rom?
Which firmware or if a custom ROM then what was the Android version?
Sent from my PLK-L01 using XDA Labs

I solved the problem in another way
After trying a thousand and one thing, the resolution to my problem was simpler than I thought.
I decided as follows:
- Having no memory card, I bought one and put in tlm
- I drew a full back to my rom, in this case a custom 6.9.1
- I put this full rom (zip file) on the memory card
- Through the TWRP did factory reset through the bootloader option
- Again by TWRP I chose installed the full rom had put the memory card
- He installed, I restart and voilá
Note that after doing this, it took a long time to set everything up. In the second logo of honor it took about 15 or 20 minutes.

It's probably due to hardware, if 3btns method don't work you can't install a fw

b4co said:
I solved the problem in another way
After trying a thousand and one thing, the resolution to my problem was simpler than I thought.
I decided as follows:
- Having no memory card, I bought one and put in tlm
- I drew a full back to my rom, in this case a custom 6.9.1
- I put this full rom (zip file) on the memory card
- Through the TWRP did factory reset through the bootloader option
- Again by TWRP I chose installed the full rom had put the memory card
- He installed, I restart and voilá
Note that after doing this, it took a long time to set everything up. In the second logo of honor it took about 15 or 20 minutes.
Click to expand...
Click to collapse
Glad you found a way to make it work
Sent from my H60-L04 using XDA Labs

Stock on TWRP loadingscreen

Hello Guys,
I have a huge Problem! I installed Twrp and CosmosOS.. after that I installed Magisk. I clicked long on the reboot button and clicked reboot recovery. It rebooted but now I am stuck in the TWRP loadingscreen and can't do anything.. I tryed to adb reboot bootloader, came back to the loadingscreen.. I also tryed to click all the combination to get somewhere but nothing worked.. Please someone help me... Im lost..

Worse case you could just flash stock images and start over. Could first try flashing twrp recovery image

ThePrinoob said:
Hello Guys,
I have a huge Problem! I installed Twrp and CosmosOS.. after that I installed Magisk. I clicked long on the reboot button and clicked reboot recovery. It rebooted but now I am stuck in the TWRP loadingscreen and can't do anything.. I tryed to adb reboot bootloader, came back to the loadingscreen.. I also tryed to click all the combination to get somewhere but nothing worked.. Please someone help me... Im lost..
Click to expand...
Click to collapse
What's your phone model (variant) ? Can you still access to the bootloader or the erecovery?
Sent from my HUAWEI BKL-L09 using XDA Labs

youtuber123 said:
What's your phone model (variant) ? Can you still access to the bootloader or the erecovery?
Click to expand...
Click to collapse
I have a BKL-L09.
If I drain the battery to 0% I can acces CosmicOS now, but if I do a reboot it reboots back to this screen.. I can acces erecovery, but not the BL..

Is there an bootloader button? Like Power + Volume up, for recovery?

Try open cmd
Adb shell halt, after that pull USB from device.
This works for me to shut down the device.
Now connect phone with USB and hold vol -
Your phone starts in bootloader
Powered by View 10

I had the same Problem! I used the buttoncombination vol- & power - when the Phone boots, plug your USB cable that is plugged into your Computer in the Phone and you will boot into fastboot mode. Flash stock Images available via Firmware Finder, extract SYSTEM.IMG from UPDATE.APP. you will lose all data from your internal sd :/

Thanks for you're help