htc one e8 dual sim[India] stuck at boot screen after OTA update[android 6.0] - HTC One E8

Hello,
Today I got notification for my marshmallow update for my HTC one e8. But I had TWRP recovery in my mobile and S-ON. and somewhere on youtube I watched a video how to get OTA update on rooted HTC ONE devices so follow the following steps :
1) Get back to your stock recovery : - which did by taking the recovery.img file from update package and flashing the recovery using fastboot.[which removes twrp with this new recovery].
2) then i started installing the update which I think successfully installed.
but when it rebooted it stuck at the boot screen. Then after 3-4 hours I factory reset my cell by visiting boot loader. But nothing happens and now I am stuck . Please help me how to recover my phone.
Also I am not able to change back the recovery to TWRP, as in fastboot device is undetectable.
so is there any way to get back my phone from TWRP backup which I made earlier when I installed TWRP

Solution
I faced a similar solution and i'd suggest you to do the following
The main issue was that adb debugging was off so its wasn't getting detected in the fastboot shell in the pc.
Install htc mobile drivers on my pc (google it, you can find this easily).
Keep the phone in HBOOT mode and connect it to the pc. Open device manager in the pc, you will now see that your htc device is now listed there.
Now open the command prompt from adb and fastboot folder. Switch the phone into FASTBOOT mode.
Now give the command: adb devices .
Do not worry if your device is still not shown in the list of devices attached.
Give the command : fastboot reboot-bootloader
Your phone should reboot in the bootloader mode again. If this happens, it confirms that the device is successfully connected to the pc . :good:
Now you flash custom recovery in your phone using the command :
fastboot flash recovery "<name-of-the-recovery>.img"
Then reboot the phone using :
fastboot reboot
Now try to enter into recovery mode. Your custom recovery will open up.
Now you can restore a twrp backup (I'm assuming that you have one. It is always recommended to have a backup of your phone whwnever you root your phone).
Reboot and you are done !!

avi2693 said:
Hello,
Today I got notification for my marshmallow update for my HTC one e8. But I had TWRP recovery in my mobile and S-ON. and somewhere on youtube I watched a video how to get OTA update on rooted HTC ONE devices so follow the following steps :
1) Get back to your stock recovery : - which did by taking the recovery.img file from update package and flashing the recovery using fastboot.[which removes twrp with this new recovery].
2) then i started installing the update which I think successfully installed.
but when it rebooted it stuck at the boot screen. Then after 3-4 hours I factory reset my cell by visiting boot loader. But nothing happens and now I am stuck . Please help me how to recover my phone.
Also I am not able to change back the recovery to TWRP, as in fastboot device is undetectable.
so is there any way to get back my phone from TWRP backup which I made earlier when I installed TWRP
Click to expand...
Click to collapse
im facing the same problem ... how will i update to marshmallow???
M8sd dwgl indian

skm14 said:
I faced a similar solution and i'd suggest you to do the following
The main issue was that adb debugging was off so its wasn't getting detected in the fastboot shell in the pc.
Install htc mobile drivers on my pc (google it, you can find this easily).
Keep the phone in HBOOT mode and connect it to the pc. Open device manager in the pc, you will now see that your htc device is now listed there.
Now open the command prompt from adb and fastboot folder. Switch the phone into FASTBOOT mode.
Now give the command: adb devices .
Do not worry if your device is still not shown in the list of devices attached.
Give the command : fastboot reboot-bootloader
Your phone should reboot in the bootloader mode again. If this happens, it confirms that the device is successfully connected to the pc . :good:
Now you flash custom recovery in your phone using the command :
fastboot flash recovery "<name-of-the-recovery>.img"
Then reboot the phone using :
fastboot reboot
Now try to enter into recovery mode. Your custom recovery will open up.
Now you can restore a twrp backup (I'm assuming that you have one. It is always recommended to have a backup of your phone whwnever you root your phone).
Reboot and you are done !!
Click to expand...
Click to collapse
thanks skm14 finally I recovered my cellphone from that boot loop.

freakkit said:
im facing the same problem ... how will i update to marshmallow???
M8sd dwgl indian
Click to expand...
Click to collapse
There's a topic posted in xda forum itself. Its quite complicated and i haven't tried it yet, So do at your own risk.
Here's the link : http://forum.xda-developers.com/one-e8/general/fix-s-devices-bootloop-ota-update-t3206840

freakkit said:
im facing the same problem ... how will i update to marshmallow???
M8sd dwgl indian
Click to expand...
Click to collapse
Actually I don't know. But I tried one method and stuck in boot loop so I will wait for other solutions.

avi2693 said:
Actually I don't know. But I tried one method and stuck in boot loop so I will wait for other solutions.
Click to expand...
Click to collapse
Even im in bootloop hope htc releases a fixed update or we get stock MM in xda

freakkit said:
Even im in bootloop hope htc releases a fixed update or we get stock MM in xda
Click to expand...
Click to collapse
hey finally I updated my cellphone to MM.
if you are in bootloop then follow the above steps given by skm14. [for this step you can get TWRP backup for you phone from http://forum.xda-developers.com/one-e8/help/htc-one-e8-mid-cid-ruu-ota-twrp-t2903210 ]
And then follow these steps which is given by firegun : http://forum.xda-developers.com/showpost.php?p=66489008&postcount=82 ( But replace the "fastboot oem relock " with "fastboot oem lock".)
if u want RUU the follow this link : http://forum.xda-developers.com/showpost.php?p=66489660&postcount=84
after doing the above steps just download the OTA updates from setting->about->software update one by one and you will be able to update to MM

avi2693 said:
hey finally I updated my cellphone to MM.
if you are in bootloop then follow the above steps given by skm14. [for this step you can get TWRP backup for you phone from http://forum.xda-developers.com/one-e8/help/htc-one-e8-mid-cid-ruu-ota-twrp-t2903210 ]
And then follow these steps which is given by firegun : http://forum.xda-developers.com/showpost.php?p=66489008&postcount=82 ( But replace the "fastboot oem relock " with "fastboot oem lock".)
if u want RUU the follow this link : http://forum.xda-developers.com/showpost.php?p=66489660&postcount=84
after doing the above steps just download the OTA updates from setting->about->software update one by one and you will be able to update to MM
Click to expand...
Click to collapse
is it working with just twrp backup or do we need RUU.

freakkit said:
is it working with just twrp backup or do we need RUU.
Click to expand...
Click to collapse
hey listen to update your cellphone to MM using OTA updates you need to have a re locked bootloader or you should not have any SU binaries in your phone so to do this you need RUU. If you are able to connect your cellphone to ypur PC and able to use fastboot then using fastboot just relock the phone using above mentioned commands and then use RUU to get back to stock lollipop ROM and the start updating using OTA. I did yesterday all these and now I have MM in my cell and its working fine with sense 7 ( which means no restrictions on themes).

avi2693 said:
( But replace the "fastboot oem relock " with "fastboot oem lock".)
Click to expand...
Click to collapse
sorry for my mistake
Thanks for Error correction, Now it is updated:good:

avi2693 said:
.
Click to expand...
Click to collapse
Hi do you have any backup of MM OTA (update.zip)?, if so can you provide me a link to download?
because i made something wrong while rooting, now my phone is in boot loop
and have you rooted your phone after update to MM?

firegun said:
Hi do you have any backup of MM OTA (update.zip)?, if so can you provide me a link to download?
because i made something wrong while rooting, now my phone is in boot loop
and have you rooted your phone after update to MM?
Click to expand...
Click to collapse
I have the first OTA which was of 94 MB but I do not have the OTA which was 1.09 GB bcoz I was not able to find this in the download folder of the internal storage. If you want that 94 MB OTA than I can provide you that but not the others :
https://mega.nz/#!NRc1kIZD!ZuliXc-VgzJ3XkahuBBvO9ROmC_z1elXemGuWMoss4Q
NO, I have not rooted my phone after update becoz I am waiting for other update which might arrive if there is any bug in the current update, I will root my phone after 1 month.

avi2693 said:
I have the first OTA which was of 94 MB but I do not have the OTA which was 1.09 GB bcoz I was not able to find this in the download folder of the internal storage. If you want that 94 MB OTA than I can provide you that but not the others :
https://mega.nz/#!NRc1kIZD!ZuliXc-VgzJ3XkahuBBvO9ROmC_z1elXemGuWMoss4Q
NO, I have not rooted my phone after update becoz I am waiting for other update which might arrive if there is any bug in the current update, I will root my phone after 1 month.
Click to expand...
Click to collapse
Thank you:good::good:

firegun said:
Thank you:good::good:
Click to expand...
Click to collapse
Dear all Dual SIM Indian M8SD users,
Please could you share your experience of updating to MM? I am having no network connection with SIM slot 2. SIM slot 1 is fine.
I then downgraded to Lollipop by flashing the RUU via fastboot after erasing the phone memory via TWRP recovery. Both SIM started working perfectly again. Then did an OTA update in four stages (from 2.33.720.3 to 2.33.720.4 to 2.33.720.6 to 2.33.720.8 to 3.06.720.2 MM) to Marshmallow.
Same problem with SIM 2 again. In the meantime, have tried various other tweaks (all combinations of settings/ removing SIMS and back in/factory resets etc.). None works.
Any help and ideas will be really appreciated.
Many thanks.

avi2693 said:
hey listen to update your cellphone to MM using OTA updates you need to have a re locked bootloader or you should not have any SU binaries in your phone so to do this you need RUU. If you are able to connect your cellphone to ypur PC and able to use fastboot then using fastboot just relock the phone using above mentioned commands and then use RUU to get back to stock lollipop ROM and the start updating using OTA. I did yesterday all these and now I have MM in my cell and its working fine with sense 7 ( which means no restrictions on themes).
Click to expand...
Click to collapse
Thanks I updated to MM last week... The RUU solution worked like a charm..
Where u able to find a way to Soff the device?

Related

[Discontinued][Recovery][Stock] XOLO Play T1000

In case you ever want to claim warranty.
Instructions:
Download ADB and recovery.zip.
Extract both to same folder.
Power down device.
Reboot into fastboot by pressing the 'Volume up + Power' buttons.
Connect phone to PC using USB cable
Open Command Prompt and CD to the ADB directory.
Type the command below
Code:
fastboot flash recovery recovery.img
Code:
fastboot reboot
Downloads:
ADB and Fastboot courtesy @ankur850 from here https://docs.google.com/file/d/0B1S0LCuXCnnmSWh6NGJmSE1BUWc/edit
Stock recovery from here: http://www.mediafire.com/download/j7h4u4x2nfnm676/recovery.zip
Hit Thanks :good: if this thread is helpful.
Refer this link for commonly asked questions before posting your doubts.
stuck at waiting for device
hi , i am trying to restore my xolo play to stock odexed rom provided at http://forum.xda-developers.com/showthread.php?p=44264063
. when i connected my phone , its saying waiting for the device. I know i am missing some drivers . Can you explain the procedure to install the drivers.
Thanks.
deepaktom said:
In case you ever want to claim warranty.
Instructions:
Download ADB and recovery.zip.
Extract both to same folder.
Power down device.
Reboot into fastboot by pressing the 'Volume up + Power' buttons.
Connect phone to PC using USB cable
Open Command Prompt and CD to the ADB directory.
Type the command below
Code:
fastboot flash recovery recovery.img
Code:
fastboot reboot
Downloads:
ADB and Fastboot courtesy @ankur850 from here https://docs.google.com/file/d/0B1S0LCuXCnnmSWh6NGJmSE1BUWc/edit
Stock recovery from here: http://www.mediafire.com/download/j7h4u4x2nfnm676/recovery.zip
Hit Thanks :good: if this thread is helpful.
Click to expand...
Click to collapse
sreekar said:
hi , i am trying to restore my xolo play to stock odexed rom provided at http://forum.xda-developers.com/showthread.php?p=44264063
. when i connected my phone , its saying waiting for the device. I know i am missing some drivers . Can you explain the procedure to install the drivers.
Thanks.
Click to expand...
Click to collapse
Try this
http://forum.xda-developers.com/showthread.php?p=43981028
installed drivers: but returns Failed
Hi i was able to install drivers. after lot of searching.
now when i sent command "astboot oem get_identifier_token" it is aying Failed.
when i searched , i found out that bootloader needs to be unlocked. can you explain in steps how to do this? and will i loose warrenty if i do this?
currently :
i did an ota update. its resulting in improper video playback. so i want to flash recovery rom.
thanks.
deepaktom said:
Try this
http://forum.xda-developers.com/showthread.php?p=43981028
Click to expand...
Click to collapse
sreekar said:
Hi i was able to install drivers. after lot of searching.
now when i sent command "astboot oem get_identifier_token" it is aying Failed.
when i searched , i found out that bootloader needs to be unlocked. can you explain in steps how to do this? and will i loose warrenty if i do this?
currently :
i did an ota update. its resulting in improper video playback. so i want to flash recovery rom.
thanks.
Click to expand...
Click to collapse
This one is not like other phones man. Boot loader is already unlocked
Sent from my XOLO Play using Tapatalk 2
sreekar said:
Hi i was able to install drivers. after lot of searching.
now when i sent command "astboot oem get_identifier_token" it is aying Failed.
when i searched , i found out that bootloader needs to be unlocked. can you explain in steps how to do this? and will i loose warrenty if i do this?
currently :
i did an ota update. its resulting in improper video playback. so i want to flash recovery rom.
thanks.
Click to expand...
Click to collapse
The bootloader is already unlocked & to flash recovery ,use instruction given by deepak or use app flashify from play store
Flashing with a custom rom.
har****181 said:
The bootloader is already unlocked & to flash recovery ,use instruction given by deepak or use app flashify from play store
Click to expand...
Click to collapse
hi,
from the link,
http://forum.xda-developers.com/wiki/index.php?title=Flashing_Guide_-_Android
i don't have custom recovery installed.
and i don't have a memory card.
what i need to do if i want to install odexed rom install.
does custom recovery installation involves rooting phone?
is it not possible to flash unrooted phones?
update:
i did
fastboot flash boot boot.img
from the boot.img file from odexed rom zip.
Is my warranty still intact?
what i did by flashing the boot partition?
boot.img is only 8 MB what is the other content present in the rom zip file and how its used?
thanks,
sreekar
sreekar said:
hi,
from the link,
http://forum.xda-developers.com/wiki/index.php?title=Flashing_Guide_-_Android
i don't have custom recovery installed.
and i don't have a memory card.
what i need to do if i want to install odexed rom install.
does custom recovery installation involves rooting phone?
is it not possible to flash unrooted phones?
update:
i did
fastboot flash boot boot.img
from the boot.img file from odexed rom zip.
Is my warranty still intact?
what i did by flashing the boot partition?
boot.img is only 8 MB what is the other content present in the rom zip file and how its used?
thanks,
sreekar
Click to expand...
Click to collapse
OK I'll spend some time here so you can understand. Warranty can be checked in most phones with locked bootloaders . ours is not locked. Bootloader locked means no change can be made unofficially by us.
The only way they can find warranty on our phone is if you use official root method.
For this purpose we have unofficial root method.
Now about partitions. /boot is the kernel. Its like drivers for your hardware.
/system is the os. It is either rooted or unrooted like in windows having admin account or normal account.
You can either use an OS which has already admin account by using a rooted ROM or you can use a limited unrooted ROM and then root it thereby making it an admin account.
Now recovery is a mini OS which will help you to recover your OS in case something is wrong. Stock recovery has limited options and allows only official updates. Custom recovery has more options and allows unofficial updates like our prerooted already admin OS/ROM.
Finally fast boot is like your Intel BIOS. Whatever happens as long as it is working you're saved. All other things like recovery, boot, system can be modified from here.
Now you flashed boot.img using fast boot and if you got a success message you're good. Use a recovery image in one of the xolo play threads and flash it using the instructions provided there.
This is required for you to install ROM.
Finally, don't worry about warranty. In case you ever need warranty, follow instructions in my ROM post about warranty. Where you can flash the ROM and recovery that came with the phone. So no worries and good luck.
Edit: for you, since you're so worried, simply install cwm recovery, then install stock odexed ROM, install build.prop.zip then reinstall stock recovery and you're like how u purchased the phone.
Sent from my XOLO Play using Tapatalk 4
i m having this problem .. after typing command it keeps displaying waiting for device .. nothing happens after that .. wat am i doing wrong . ( i tired instaling drivers but it says -windows has determined software is up to date) what shud i do .. cant install ny rom too
mkr17 said:
i m having this problem .. after typing command it keeps displaying waiting for device .. nothing happens after that .. wat am i doing wrong . ( i tired instaling drivers but it says -windows has determined software is up to date) what shud i do .. cant install ny rom too
Click to expand...
Click to collapse
right click the device under device manager and select uninstall. then replug device and browse and select the driver
http://support.moulnisky.com/index.php?dir=Xolo/Xolo Play/
Here factory firmware and instructions
BR
Alex
http://forum.xda-developers.com/showpost.php?p=47122148&postcount=881
Posted the same here
btw, There is an S018 fw out too. Those linked above are outdated.
Free Radical said:
http://forum.xda-developers.com/showpost.php?p=47122148&postcount=881
Posted the same here
btw, There is an S018 fw out too. Those linked above are outdated.
Click to expand...
Click to collapse
Yes,
Already added it in the support area
BR
Alex
mr moulinsky i have karbonn A8 device i flash software but now device is show fizzy and white display with china sound no karbonn logo please help me how to flash karbonn A8 with right flash files
Sent from my Micromax A76 using XDA Premium 4 mobile app
HELP!!
kkbs4u said:
mr moulinsky i have karbonn a8 device i flash software but now device is show fizzy and white display with china sound no karbonn logo please help me how to flash karbonn a8 with right flash files
sent from my micromax a76 using xda premium 4 mobile app
Click to expand...
Click to collapse
my xolo play t1000 is locked due to too many pattern locks. Now it is asking for gmail id & password but my data is off. Now i got struck as my xolo secure is on i cannot wipe data/factory reset the phone. What should i do to unlock also i dont want to loose my warranty.i also cannot visit the service center as it will cost me a flight fare of 6000 bucks. Help me!!!!
Thanks in advance..
morning.revz08 said:
my xolo play t1000 is locked due to too many pattern locks. Now it is asking for gmail id & password but my data is off. Now i got struck as my xolo secure is on i cannot wipe data/factory reset the phone. What should i do to unlock also i dont want to loose my warranty.i also cannot visit the service center as it will cost me a flight fare of 6000 bucks. Help me!!!!
Thanks in advance..
Click to expand...
Click to collapse
try booting into recovery and factory resetting the device...press vol down+power button to boot into recovery and then wipe data/factory reset

[Q] HTC One Mini not booting up fully and no access to recovery

Hello,
My phone was updating and crashed. The phone turns on but only the HTC logo appears and then goes to a black screen. I can't fastboot into the device as it is not recognised. I can't access TWRP recovery any more and goes to a downloading screen and then restarts again. While in the bootloader the phone shows the following:
***TAMPERED***
*** RELOCKED***
M4_UL PVT SHIP S-OFF RL
CID-11111111
HBOOT-2.19.0000
RADIO-1.22.40e.00.07
OpenDSP-v19.2.0268.0927
OS-1.31.401.1
eMMC-boot 1024MB
Aug 7 2013, 17:37:54.0
Please help me, any help greatly appreciated!
Update:
The phone is working and has an update but it can not update on the device, is there a way i can get the downloaded OTA file on to my PC?
CoolAndroid1 said:
Hello,
My phone was updating and crashed. The phone turns on but only the HTC logo appears and then goes to a black screen. I can't fastboot into the device as it is not recognised. I can't access TWRP recovery any more and goes to a downloading screen and then restarts again. While in the bootloader the phone shows the following:
***TAMPERED***
*** RELOCKED***
M4_UL PVT SHIP S-OFF RL
CID-11111111
HBOOT-2.19.0000
RADIO-1.22.40e.00.07
OpenDSP-v19.2.0268.0927
OS-1.31.401.1
eMMC-boot 1024MB
Aug 7 2013, 17:37:54.0
Please help me, any help greatly appreciated!
Click to expand...
Click to collapse
Hi,
What do you want to flash stock sense 6...??
greets
shivasrage said:
Hi,
What do you want to flash stock sense 6...??
greets
Click to expand...
Click to collapse
Hello,
Yes I would like to go back to Sense 6 or any stock firmware preferably 4.4.2
Thanks
CoolAndroid1 said:
Hello,
Yes I would like to go back to Sense 6 or any stock firmware preferably 4.4.2
Thanks
Click to expand...
Click to collapse
Ok
First I recommend you to unlock your bootloader.
So if you are in bootloader and your device is not recognised I think it´s a driver issue.
If you allready checked it check it once more or update your tools (ADB, fastboot)
If nothing helps you could go to recovery and format your device (not only wipe format) should be clear that all data on device is lost.
Try different recoverys some people report that philz also works fine on M_4. (try install new rom option on philz).
DONT flash stock sense 6 ROM (wrong partition layout for this hboot) with this hboot rather take 5.5.
I´m sorry but without get connectet via ADB or fastboot I think there is no chance to get it working again.
greets
shivasrage said:
Ok
So if you are in bootloader and your device is not recognised I think it´s a driver issue.
If you allready checked it check it once more or update your tools (ADB, fastboot)
If nothing helps you could go to recovery and format your device (not only wipe format) should be clear that all data on device is lost.
Try different recoverys some people report that philz also works fine on M_4. (try install new rom option on philz).
DONT flash stock sense 6 ROM (wrong partition layout for this hboot) with this hboot rather take 5.5.
With out get connectet via ADB or fastboot I think there is no chance to get it working again.
greets
Click to expand...
Click to collapse
I can not access recovery to wipe anything out, on bootloader if i choose to wipe it attempts to load recovery which goes into download mode. The device comes up as "Device failed emulation" on Windows 8
CoolAndroid1 said:
I can not access recovery to wipe anything out, on bootloader if i choose to wipe it attempts to load recovery which goes into download mode. The device comes up as "Device failed emulation" on Windows 8
Click to expand...
Click to collapse
Ok
I tell you in short terms:
If you can´t get a fastboot connection to your device it looks very bad to bring your device back.
For wiping something you need recovery for flashing new recovery you need fastboot.
For flashing a new firmware to fix messed up partitions you need fastboot.
And first of all to unlock your bootloader you need fastboot.
You see all ends up with fastboot.
As what the device is shown in the manager of windows?
Better to use Windows 7 there are much driver problems people reporting on win 8
greets
Ok, I will use a win 7 pc and let you know
shivasrage said:
Ok
I tell you in short terms:
If you can´t get a fastboot connection to your device it looks very bad to bring your device back.
For wiping something you need recovery for flashing new recovery you need fastboot.
For flashing a new firmware to fix messed up partitions you need fastboot.
And first of all to unlock your bootloader you need fastboot.
You see all ends up with fastboot.
As what the device is shown in the manager of windows?
Better to use Windows 7 there are much driver problems people reporting on win 8
greets
Click to expand...
Click to collapse
After i fix my drivers issue what can i do afterwards?
shivasrage said:
Ok
I tell you in short terms:
If you can´t get a fastboot connection to your device it looks very bad to bring your device back.
For wiping something you need recovery for flashing new recovery you need fastboot.
For flashing a new firmware to fix messed up partitions you need fastboot.
And first of all to unlock your bootloader you need fastboot.
You see all ends up with fastboot.
As what the device is shown in the manager of windows?
Better to use Windows 7 there are much driver problems people reporting on win 8
greets
Click to expand...
Click to collapse
I can now do the fastboot command from CMD
CoolAndroid1 said:
After i fix my drivers issue what can i do afterwards?
Click to expand...
Click to collapse
If you have a connection via fastboot you first have to decide what ROM you want, search for the matching firmware.
for example flash the latest firmware for M_4... 4.09.401.3 from here (new partition layout for e.g. sense 6):
https://docs.google.com/file/d/0BzCFBBNdXagdcEMybkdBME5iUE0/edit
After that flash TWRP 2.7.1.1 or philz and format all you have to try one of this recoverys should work.
Next push or sideload a ROM via adb I recommend you one them:
http://forum.xda-developers.com/htc...-official-stock-sense-6-rom-firmware-t2817921
You can decide what you want rooted or not it doesn´t matter.
After installing with succsess try to reboot that´s it.
greets
I encountered a similar issue when playing around with returning my device to stock. I flashed stock recovery, then re-locked my bootloader. What is the downloading screen you're seeing? Is it the stock recovery screen?
To fix, i had to change CID back to stock (for me that was, CWS__001)
Unlock bootloader again, using HTC unlock.bin (unlock.bin wouldn't work when i was on super cid)
Flash custom recovery TWRP 2.6.3.0 (I'm not sure if 2.7.1.1 works with the old partition layout, so i used this version until i had upgraded to hboot 2.22, then I flashed 2.7.1.1. This may be an unnecessary step, but it always worked for me)
Once twrp was working again...
Flash stock hboot 2.22 found in the dev section
Flash TWRP 2.7.1.1 (again, might be an unnecessary step)
Boot to recovery
From TWRP, adb push the sense 6 rom i wanted to flash (IC 3.07 in my case)
After the push completed, flash ROM and reboot and all was good
As you can see, the steps i took require that fastboot and adb drivers work flawlessly, especially when pushing ROM to the device using abd.
If any of this seems unfamiliar, then don't do these steps. Again, this is just what i did when i flashed stock recovery and re-locked bootloader with a ROM that wouldn't boot.
jollywhitefoot said:
I encountered a similar issue when playing around with returning my device to stock. I flashed stock recovery, then re-locked my bootloader. What is the downloading screen you're seeing? Is it the stock recovery screen?
To fix, i had to change CID back to stock (for me that was, CWS__001)
Unlock bootloader again, using HTC unlock.bin (unlock.bin wouldn't work when i was on super cid)
Flash custom recovery TWRP 2.6.3.0 (I'm not sure if 2.7.1.1 works with the old partition layout, so i used this version until i had upgraded to hboot 2.22, then I flashed 2.7.1.1. This may be an unnecessary step, but it always worked for me)
Once twrp was working again...
Flash stock hboot 2.22 found in the dev section
Flash TWRP 2.7.1.1 (again, might be an unnecessary step)
Boot to recovery
From TWRP, adb push the sense 6 rom i wanted to flash (IC 3.07 in my case)
After the push completed, flash ROM and reboot and all was good
As you can see, the steps i took require that fastboot and adb drivers work flawlessly, especially when pushing ROM to the device using abd.
If any of this seems unfamiliar, then don't do these steps. Again, this is just what i did when i flashed stock recovery and re-locked bootloader with a ROM that wouldn't boot.
Click to expand...
Click to collapse
I cant unlock my bootloader as its relocked and fails, I cant install TWRP either
CoolAndroid1 said:
I cant unlock my bootloader as its relocked and fails, I cant install TWRP either
Click to expand...
Click to collapse
Did you get fastboot working yet? Does "fastboot devices" show your device? You can't do anything until fastboot works...but I imagine it worked at some point, since you unlocked and re-locked your device.
You can't install recovery because your bootloader is locked. And you can't unlock your bootloader until you change your CID back to whatever it was when you created the unlock.bin file on the HTC website.
Are you getting this error when you attempt to unlock?
FAILED (remote: unlock token check failed)
jollywhitefoot said:
Did you get fastboot working yet? Does "fastboot devices" show your device? You can't do anything until fastboot works...but I imagine it worked at some point, since you unlocked and re-locked your device.
You can't install recovery because your bootloader is locked. And you can't unlock your bootloader until you change your CID back to whatever it was when you created the unlock.bin file on the HTC website.
Are you getting this error when you attempt to unlock?
FAILED (remote: unlock token check failed)
Click to expand...
Click to collapse
Hello,
I did have the error code above but i used FUU to flash back to stock and all is fine now!!
CoolAndroid1 said:
Hello,
I did have the error code above but i used FUU to flash back to stock and all is fine now!!
Click to expand...
Click to collapse
Cool. Did you use fuu from here?
http://forum.xda-developers.com/showthread.php?t=2659109
jollywhitefoot said:
Cool. Did you use fuu from here?
http://forum.xda-developers.com/showthread.php?t=2659109
Click to expand...
Click to collapse
Yep! Windows 8 sucks with drivers and didn't work so had to switch to a different laptop!
CoolAndroid1 said:
Yep! Windows 8 sucks with drivers and didn't work so had to switch to a different laptop!
Click to expand...
Click to collapse
That's what i had to do when i first tried to root my phone. I was on Windows 7, but it was an old install and had all kinds of software on it that might have been preventing usb from working (iTunes, HTC Sync, some other random software, etc.) Sometimes, I would even have trouble connecting an external HD!
I ended up installing a clean copy of XP on an old computer that i now use strictly for flashing stuff to my phone.
New problem
I have 4.3 on my HTC now and have received an update for 4.4.2, however when I try this it goes a quarter of the way then comes up with a red triangle and exclamation point. The device is still rooted somehow. Can you help me update?
CoolAndroid1 said:
New problem
I have 4.3 on my HTC now and have received an update for 4.4.2, however when I try this it goes a quarter of the way then comes up with a red triangle and exclamation point. The device is still rooted somehow. Can you help me update?
Click to expand...
Click to collapse
I don't think OTA will work on unlocked/tampered device with custom recovery.I think you need to run ruu.exe if one is available for you to get 100% stock before OTA will work again.
jollywhitefoot said:
I don't think OTA will work on unlocked/tampered device with custom recovery.I think you need to run ruu.exe if one is available for you to get 100% stock before OTA will work again.
Click to expand...
Click to collapse
Hello,
I found an FUU for 4.4 Kitkat on the link you posted earlier, It does all the necessary actions with no failures and completes with a Congrats screen but the firmware is the same?

Minimal adb&fastboot

Hi all,
I have problem, cant install twrp recovery via minimal adb&fastboot commands. Getting error
.Phone unlocked. Adb devices command showing device connected, i can use fastboot reboot bootloader, and that all. Other commands geting failed.
I tryed many times and olders twrp files, but same problem. Plz guys help me fix it.
Unlock bootloader even if its unlocked.
Flashing command : fastboot flash recovery recovery.img
gm007 said:
Unlock bootloader even if its unlocked.
Flashing command : fastboot flash recovery recovery.img
Click to expand...
Click to collapse
Look what i get after trying unlock bootloader again, and second when try install twrp recovery.img.
Why don't you use srk tools to unlock and install the recovery.
gm007 said:
Why don't you use srk tools to unlock and install the recovery.
Click to expand...
Click to collapse
Becouse i get same problem like with minaml adb&fastboot program. Its sames cmd commands what diffrent ?
r4ason said:
Becouse i get same problem like with minaml adb&fastboot program. Its sames cmd commands what diffrent ?
Click to expand...
Click to collapse
Relock bootloader and unlock again.
What did you do to your phone.
gm007 said:
Relock bootloader and unlock again.
What did you do to your phone.
Click to expand...
Click to collapse
Already tryed. Nothing, same error. Since in phone was NXT-L29C432B320 firmware. I searched in internet its able to update to nougat. L29C432B521(beta).
I used dload method and phone get bricked. After that tryed rollback software to all older versions.And nothing, dload dont helped.
Next i writed to huawei custumservise and they gives me bootloader unlock code. I used it and succsesfull unlocked phone.
Next step was twrp revovery.img installed succsesfully.And worked fine.
Searched international custom rom for my device.And installed via twrp recovery without errors or faild. But in twrp meniu bellow i saw "os not installed"
After that phone restarted 2 times, and wont boot system. That twrp recovery disapier from phone. And until now im stuck here to find any soliution.
Yesturday i was tryed even dc unlocker pheonix program for 15€ and its not helped..
What you did with dc unlocker ,did you flash a rom?
gm007 said:
What you did with dc unlocker ,did you flash a rom?
Click to expand...
Click to collapse
With pheonix i tryed to install stock rom. Like in instruction by program.
Program installed ios, but phone wont restarted and booted to system. Nothing hapened.
r4ason said:
With pheonix i tryed to install stock rom. Like in instruction by program.
Program installed ios, but phone wont restarted and booted to system. Nothing hapened.
Click to expand...
Click to collapse
I used this https://www.dc-unlocker.com/DC-Phoenix-flash-repair-tutorial
r4ason said:
With pheonix i tryed to install stock rom. Like in instruction by program.
Program installed ios, but phone wont restarted and booted to system. Nothing hapened.
Click to expand...
Click to collapse
Step 2
After performing steps in guide your phone should boot up
Then you need to repeat flashing, but now in upgrade mode
This step is necessary to fix incorrect internal storage size after flashing in fastboot
Did you use a official firmware or a firmware from dc unlocker?
gm007 said:
Did you use a official firmware or a firmware from dc unlocker?
Click to expand...
Click to collapse
Yes i used official firmware.

[need help] asus zc520kl [x00hd] any working rom with twrp

Update/Solved:
Currently the only way for people who deleted their OS completely in this phone model X00HD/ZC520KL is to restore the official firmware.
You can ask for a backup recovery folder in XDA Forums ( https://forum.xda-developers.com/zen...help?nocache=1) if you do not have made a backup with people who have the same phone model. You must have TWRP previously installed and bootloader unlocked. Flashing the official firmware via .zip files is not working with twrp, you must restore the folder. After having the files needed, your recovery folder will not appear on the RESTORE section so follow this simple tutorial to make it appear there (https://youtu.be/trlG3ZxwQxI)
This method will bring your phone back to life if you're stuck in TWRP Recovery Mode with "No OS installed". This method is working and it's the only way for you to use your phone again until developers create custom ROM's for this model.
DEVICE INFO:
ASUS ZENFONE 4 MAX ZC520KL [X00HD]
Please, can anyone reply? I need an answer. Thanks for your time.
https://forum.xda-developers.com/zenfone-4-max/how-to/zenfone-4-max-rom-twrp-flash-twrp-t3776287
jenere said:
https://forum.xda-developers.com/zenfone-4-max/how-to/zenfone-4-max-rom-twrp-flash-twrp-t3776287
Click to expand...
Click to collapse
This ROM is for is for the Asus model of ZenFone 4 Max ZC554KL [X00ID]. My device is the same but the model is ZenFone 4 Max ZC520KL [X00HD]. Will it work also on my device? :fingers-crossed:
jenere said:
https://forum.xda-developers.com/zenfone-4-max/how-to/zenfone-4-max-rom-twrp-flash-twrp-t3776287
Click to expand...
Click to collapse
Hello, I tried your solution. It did not work. I keep getting Error Number 7 when flashing the ROM. Plus I also tried to delete the assert line in the uptader-script of the ROM you gave me the link after learning from a tutorial how to solve Error Number 7 and after that I got another error: Invalid Zip Format. I don't know what do to more, is this ROM link really compatible with my device? I need urgent help.
ANDROIDMASTER67 said:
Hello, I tried your solution. It did not work. I keep getting Error Number 7 when flashing the ROM. Plus I also tried to delete the assert line in the uptader-script of the ROM you gave me the link after learning from a tutorial how to solve Error Number 7 and after that I got another error: Invalid Zip Format. I don't know what do to more, is this ROM link really compatible with my device? I need urgent help.
Click to expand...
Click to collapse
did you try the stock firmware in the official site for asus? i think installing the the official stock firmware will solve your problem just chose there the proper firmware for.. can i ask if already unlock your bootloader or already change you stock twrp?
jenere said:
did you try the stock firmware in the official site for asus? i think installing the the official stock firmware will solve your problem just chose there the proper firmware for.. can i ask if already unlock your bootloader or already change you stock twrp?
Click to expand...
Click to collapse
Thanks for the attention. I already tried tons of ROM's including the official one for this phone. I keep getting Error Number 7. Sometimes when I force an installation editing the uptader-script file it seems everything is working fine, but at the end of the ROM flash process the phone reboots and goes back to TWRP like everything had never happened. I have never seen a successful feedback, just the "Failed" message or a unexpected reboot that goes back to TWRP.
I don't know what do you mean with unlocking bootloader as I have no ROM installed and always I turn ON my phone I go to TWRP automatically. My TWRP version is 3.1.1.
ANDROIDMASTER67 said:
Hello, I tried your solution. It did not work. I keep getting Error Number 7 when flashing the ROM. Plus I also tried to delete the assert line in the uptader-script of the ROM you gave me the link after learning from a tutorial how to solve Error Number 7 and after that I got another error: Invalid Zip Format. I don't know what do to more, is this ROM link really compatible with my device? I need urgent help.
Click to expand...
Click to collapse
https://forum.xda-developers.com/showthread.php?t=2302599 did you try this?
---------- Post added at 01:50 AM ---------- Previous post was at 01:45 AM ----------
there's alot of tutorial video in google and youtube showing how to fix error code 7 when flashing rom
jenere said:
https://forum.xda-developers.com/showthread.php?t=2302599 did you try this?
---------- Post added at 01:50 AM ---------- Previous post was at 01:45 AM ----------
there's alot of tutorial video in google and youtube showing how to fix error code 7 when flashing rom
Click to expand...
Click to collapse
Not working, as I said before, I've already tried to solve this Error. Either 3 things happen: the installation seems to be running good but at some point the device automatically reboots to it's original condition of TWRP (Liniage OS flash and after editing the file to solve Error Number 7 + I get a message saying "Invalid zip format" (Official Asus Firmware flash after editing the file to solve Error Number 7) + I get Error Number 7.
Backup ROM
Hi, I have the same model and I have TWRP as well. I think I can make backup of my ROM an upload it so you can install it on your phone, would that work for you?
pantarz said:
Hi, I have the same model and I have TWRP as well. I think I can make backup of my ROM an upload it so you can install it on your phone, would that work for you?
Click to expand...
Click to collapse
Hello @pantarz, yes, give me your backup ROM you have in your phone, it should work on mine. I'm really thankful to see people like this these days. Just need the .zip file for the ROM. Thanks in advance.
Currently the only way for people who deleted their OS completely in this phone model X00HD/ZC520KL is to restore the official firmware.
You can ask for a backup recovery folder in XDA Forums ( https://forum.xda-developers.com/zenfone-4-max/help?nocache=1) if you do not have made a backup. You must have TWRP previously installed and bootloader unlocked. Flashing the official firmware via .zip files is not working with twrp, you must restore the folder. Your recovery folder will not appear on the RESTORE section so follow this simple tutorial to make it appear there (https://youtu.be/trlG3ZxwQxI)
This method will bring your phone back to live if you're stuck in TWRP Recovery Mode with "No OS installed". This method is working and it's the only way for you to use your phone again until developers create custom ROM's for this model.
Hi @ANDROIDMASTER67, @pantarz I also break my phone ZC520KL ( X00HD ). It shows "no os installed" and "error 7" when I try to install a ROM.
Can you please help me fix my phone? If there is a backup that I can get please let me know.
Many thanks in advance.
I've managed to fix it by doing the following:
Copy the original recovery from a firmware package.
I could find one in the file https://androidfilehost.com/?fid=11050483647474829889, location /Asus_Zenfone_4_Max_ZC520KL_20171225/Firmware/recovery.img
Load default recovery
fastboot flash recovery recovery/original-recovery.img
Restart to bootloader
fastboot reboot bootloader
Load flashboot mode
choose the option "update using adb"
ensure that adb can locate devices with
adb devices
load firmware with
adb sideload UL-ASUS_X00HD-WW-14.2016.1805.374-user.zip ( try download from: https://www.beritahuaja.com/2018/11/download-stock-rom-asus-zenfone-4-max-zc520kl.html )
Easy way with only fastboot
1. Get adb and fastboot drivers
2. go to this page h ttps://addrom.com/raw-rom-for-asus-zenfone-4-max-zc520kl/ Dowload the original firware
3. Extract the files inside the your disc C:Adb
4. Go to your celphone and enter in fastboot mode... then conect the celphone to your computer ... then use cmd " fastboot flash recovery recovery.img" .. this is for restore the original recovery if you have twrp.. if you dont have it , its no neccesary ..
5. in fastboot mode , go to Inside the firware search flashall_AFT.bat , double clik , wait until finish
6. go to recovery mode wipe/factory reset and tadaaaa! Your Os is restore again :bueno:
asus-zenfone-4-max-zc520kl
Luisanchez70 said:
1. Get adb and fastboot drivers
2. go to this page h ttps://addrom.com/raw-rom-for-asus-zenfone-4-max-zc520kl/ Dowload the original firware
3. Extract the files inside the your disc C:Adb
4. Go to your celphone and enter in fastboot mode... then conect the celphone to your computer ... then use cmd " fastboot flash recovery recovery.img" .. this is for restore the original recovery if you have twrp.. if you dont have it , its no neccesary ..
5. in fastboot mode , go to Inside the firware search flashall_AFT.bat , double clik , wait until finish
6. go to recovery mode wipe/factory reset and tadaaaa! Your Os is restore again :bueno:
Click to expand...
Click to collapse
i have unlock bootloader after flash this firmware relock it agin ?
Amadu said:
I've managed to fix it by doing the following:
Copy the original recovery from a firmware package.
I could find one in the file https://androidfilehost.com/?fid=11050483647474829889, location /Asus_Zenfone_4_Max_ZC520KL_20171225/Firmware/recovery.img
Load default recovery
fastboot flash recovery recovery/original-recovery.img
Restart to bootloader
fastboot reboot bootloader
Load flashboot mode
choose the option "update using adb"
ensure that adb can locate devices with
adb devices
load firmware with
adb sideload UL-ASUS_X00HD-WW-14.2016.1805.374-user.zip ( try download from: https://www.beritahuaja.com/2018/11/download-stock-rom-asus-zenfone-4-max-zc520kl.html )
Click to expand...
Click to collapse
It works. It really works. You have saved my Asus X00HD. Thank you.
Luisanchez70 said:
Easy way with only fastboot
1. Get adb and fastboot drivers
2. go to this page h ttps://addrom.com/raw-rom-for-asus-zenfone-4-max-zc520kl/ Dowload the original firware
3. Extract the files inside the your disc C:Adb
4. Go to your celphone and enter in fastboot mode... then conect the celphone to your computer ... then use cmd " fastboot flash recovery recovery.img" .. this is for restore the original recovery if you have twrp.. if you dont have it , its no neccesary ..
5. in fastboot mode , go to Inside the firware search flashall_AFT.bat , double clik , wait until finish
6. go to recovery mode wipe/factory reset and tadaaaa! Your Os is restore again :bueno:
Click to expand...
Click to collapse
you save me
THANK YOUUUU

(guide) root nokia 3 android 9.0

Download all the files and unzip the platform-tools folder and move apk and boot to the phone memory
first we have to download magisk apk .. install and open
then we will install magisk, a window will open and we will install it and it will ask us to patch a boot image
we look for the boot image that we download ... then we click on it and the boot image will be patched ...
the patched image of awaits in in download in internal storage ..
we go to the computer and move the patched image to the desktop ..
we go to the platform-tools folder and open it and give alt and right click in an empty space and open the powershell or cmd window .. once it starts in the command window we will give it a series of commands
first: we have to activate the cell phone's usb debug and connect to the computer
in the command window we put:
cmd
adb devices (we have to detect the device)
adb reboot bootloader (or start bootloader manually)
fasboot devices (we have to detect the cell phone)
fastboot flash boot (and we move the patched image in the command window next to the last command or this one)
we give space and we give enter and the image will be installed and we give ..
fastboot reboot
and ready you have root just open magisk and it is already installed https://drive.google.com/drive/folders/1UjyAzSZeMUBIwSTvlNo1CFL7BO3dMLPW?usp=sharing
https://drive.google.com/open?id=1HtjdNjdJ3XiSaOAUNVwZ8E-tGv3xr2Ly
https://drive.google.com/open?id=1eFpvFeUe_xLRUFnBbT2ZzKdTgX8-nyYQ
I will try it and see that it breaks this time
Marakas89 said:
Download all the files and unzip the platform-tools folder and move apk and boot to the phone memory
first we have to download magisk apk .. install and open
then we will install magisk, a window will open and we will install it and it will ask us to patch a boot image
we look for the boot image that we download ... then we click on it and the boot image will be patched ...
the patched image of awaits in in download in internal storage ..
we go to the computer and move the patched image to the desktop ..
we go to the platform-tools folder and open it and give alt and right click in an empty space and open the powershell or cmd window .. once it starts in the command window we will give it a series of commands
first: we have to activate the cell phone's usb debug and connect to the computer
in the command window we put:
cmd
adb devices (we have to detect the device)
adb reboot bootloader (or start bootloader manually)
fasboot devices (we have to detect the cell phone)
fastboot flash boot (and we move the patched image in the command window next to the last command or this one)
we give space and we give enter and the image will be installed and we give ..
fastboot reboot
and ready you have root just open magisk and it is already installed https://drive.google.com/drive/folders/1UjyAzSZeMUBIwSTvlNo1CFL7BO3dMLPW?usp=sharing
Click to expand...
Click to collapse
Thanks for share
work fine in me
wirdan.hungkul said:
Thanks for share
work fine in me
Click to expand...
Click to collapse
by chance you don't have the ota? (zip), the last update available that I have is a security patch for 8.1
:c
djxpro said:
by chance you don't have the ota? (zip), the last update available that I have is a security patch for 8.1
:c
Click to expand...
Click to collapse
I don't have Ota update ..., you should re-flash your device
wirdan.hungkul said:
I don't have Ota update ..., you should re-flash your device
Click to expand...
Click to collapse
Well, remember something: I guess for it to work, the bootloader must be disabled, right?
:c
djxpro said:
Well, remember something: I guess for it to work, the bootloader must be disabled, right?
:c
Click to expand...
Click to collapse
bootloader must be activated ..
wirdan.hungkul said:
bootloader must be activated ..
Click to expand...
Click to collapse
I tried it with 8.1 files
and cmd show me a device locked error
It may be by the method in the wrong version.
djxpro said:
I tried it with 8.1 files
and cmd show me a device locked error
It may be by the method in the wrong version.
Click to expand...
Click to collapse
try this https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-unlock-bootloader-nokia-3-t3699344
if an error still occurs
try flash it https://forum.xda-developers.com/nokia-3/how-to/nokia-3-ta-1032-official-firmware-sp-t3744634
and if after Flash Dead And Vibrate only
https://www.youtube.com/watch?v=zW6srLB5fBM
wirdan.hungkul said:
try this https://forum.xda-developers.com/nokia-3/how-to/guide-how-to-unlock-bootloader-nokia-3-t3699344
if an error still occurs
try flash it https://forum.xda-developers.com/nokia-3/how-to/nokia-3-ta-1032-official-firmware-sp-t3744634
and if after Flash Dead And Vibrate only
https://www.youtube.com/watch?v=zW6srLB5fBM
Click to expand...
Click to collapse
I tried the first thing and it throws me another different mistake.
something like unknown command.
or something concerning the communication with the device
and the other link is a 7.1 rom, right?
my device is the ta 1028...
technically it is the same
djxpro said:
I tried the first thing and it throws me another different mistake.
something like unknown command.
or something concerning the communication with the device
and the other link is a 7.1 rom, right?
my device is the ta 1028...
technically it is the same
Click to expand...
Click to collapse
is it already installed mtk driver?
https://androidmtk.com/download-mtk-driver-auto-installer
or
https://androidmtk.com/download-mtk-usb-all-drivers
yes, anothet link 7.0 and 7.1 rom...
or you can try https://forum.xda-developers.com/nokia-3/how-to/nokia-3-official-firmware-india-uae-t3674320
Firmware supported for below Nokia 3 Supported Models
- NOKIA 3 TA-1032 DS
- NOKIA 3 TA-1020 SS
- NOKIA 3 TA-1028 SS
- NOKIA 3 TA-1038 DS
Apparently it is an issue of the operator that I do not have the update yet.
I went back to 8.0 while I find out what happened to the ota.
And if it comes out I'll capture it.
wirdan.hungkul said:
is it already installed mtk driver?
https://androidmtk.com/download-mtk-driver-auto-installer
or
https://androidmtk.com/download-mtk-usb-all-drivers
yes, anothet link 7.0 and 7.1 rom...
or you can try https://forum.xda-developers.com/nokia-3/how-to/nokia-3-official-firmware-india-uae-t3674320
Firmware supported for below Nokia 3 Supported Models
- NOKIA 3 TA-1032 DS
- NOKIA 3 TA-1020 SS
- NOKIA 3 TA-1028 SS
- NOKIA 3 TA-1038 DS
Click to expand...
Click to collapse
well, finally, i have android 9.
but, i cant flash the patched boot
:c failed: unknown command
Well, I managed to root.
I got the OTA in a Russian forum.
After a couple of failed attempts, I managed to figure out how to mount the OTA.
Then, not working or rooting, and realize that the bootloader was not unlocked, I repeated all the steps.
I noticed that I am subnormal, and that the code I was using to unlock was not correct (several months to realize this).
Anyway, go down to 7.1, unlock the bootloader, flash to 8.1 (4.42) (orange state up)
I mounted OTA 5.20 through recovery
I did the steps in the post, and finally I have Pie with root
Orange State continues, but I will not block the bootloader again
djxpro said:
Well, I managed to root.
I got the OTA in a Russian forum.
After a couple of failed attempts, I managed to figure out how to mount the OTA.
Then, not working or rooting, and realize that the bootloader was not unlocked, I repeated all the steps.
I noticed that I am subnormal, and that the code I was using to unlock was not correct (several months to realize this).
Anyway, go down to 7.1, unlock the bootloader, flash to 8.1 (4.42) (orange state up)
I mounted OTA 5.20 thrgough recovery
I did the steps in the post, and finally I have Pie with root
Orange State continues, but I will not block the bootloader again
Click to expand...
Click to collapse
:good:
Well.....i thought let me give it a try.....but.....problem started then...
--- adb works fine.....both the commands (adb devices and adb reboot bootloader) gets executed
--- but my device doesn't get detected in fastboot mode
--- thinking that its problem with drivers...i tried every driver (adb and fastboot) out in the internet and nokia drivers...but got no luck
--- hoping that someone could help me i posted here.... thanks in advance
djxpro said:
well, finally, i have android 9.
but, i cant flash the patched boot
:c failed: unknown command
Click to expand...
Click to collapse
i found a way to flash the patched boot and unlock the bootloader on pie
Here
NulledRoot said:
i found a way to flash the patched boot and unlock the bootloader on pie
Here
Click to expand...
Click to collapse
actually, i have a rooted phone.
but, i lock the bootloader again, and now, i need connect to usb to start up
without usb, i give a red state
.-.)
my phone stuck at reboot loop can someone help me?

Categories

Resources