Database Info

[Help] Blu Vivo 4.8

Hello friends, I need your help...
Since i did a Dalvik-Cache clean on my phone, it got stuck on the bootlogo...
I can't find anywhere the stock rom and the scatter file to try amend this with SPTool since I dont have CWM or TWRP.
If there is a way to just get my files, pictures and music back will be enough help...
:crying:

Since no one bothered to help me, I managed to find a solution.
Will share here what i done.
1- Downloaded adb and put at C:/adb
2- Downloaded my phone usb/adb drivers.
3- Put my phone into factory mode by holding Volume-down key and power
4- By doing previous step and connecting the usb cable on the phone to pc, is possible to use adb commands
5- Used the command = adb pull /storage/sdcard0 C:/adb/Phone-Files (Can't start "adb shell" otherwise file/folder copy is blocked) from the cmd at the adb folder
6- Waited a hour and half to get everything from my phone to the folder = C:/adb/Phone-Files
I'm on my way to learn how to fix the Dalvik-Cache deletion.
Maybe getting the stock rom somewhere and using pull may solve... :fingers-crossed:

[GUIDE] Repair bootloop wrong recovery flash Huawei Honor 3X G750-u10

this tutorial, is for repairing the huawei g750-u10 in case you flashed the wrong recovery and now you're stuck in a bootloop.
First of all you will need (it's all in the link to download, make shure you have a sdcard on your phone before starting):
-Adb install setup
-Adb toolkit
-vcom drivers
mega.co.nz/#!gURHXDoZ!QNmv7LaK8r4WIQBGaUyoNho3TPX0YZp9jwHaEHgDmII
note:the recovery.img provided on the rar file only works for the U10, the method might work for other models but with a diferent recovery file.
-Installation of the phone mediatek drivers:
-Start with installing th vcom drivers i provided on the rar file, type HDWWIZ on the windows search tab:
Install the hardware manually>Ports(com&lpt)>Have a disk>select the file wich corresponds to you windows>mediatekpreloader usb vcom port> restart your computer. (if this method doesn't work for you try to search for vcom driver installation tutorials)
-Installing adb
-double click on the adb-setup.exe file provided and install it including drivers.
-the adb tool kit doesn't need installation just run the Adb toolkit Gui
on adb toolkit, type the command fastboot continue as shown in the picture
s13.postimg.org/yuauaawpj/Untitled.jpg
Remove the battery from your mobile phone, wait 5s plug it in again. Connect the usb to the computer and pluh it to your phone and at the same time push the power button till it turns on but keep your finger in the VOLUME DOWN all the time, it may reboot 2 times but then you will get the fastboot/repair mode image you can now lift your finger.
When you are in fastboot connected to your computer (the mediatek drivers will install wait for installation to complete).
Now return to the Adb GUI and press the execute command, (it will appear 3 lines starting with something saying error dont mind that it's normal) and wait a few seconds then your phone will restart it self and boot normally.
You're allmost there:
-When your phone boots, select the usb connection to usb mass storage device.
-copy the recovery.img provided to the root of your sdcard, safely unplug the phone from your pc.
-download and install the mobile mtk uncle tools app from the playstore.
-turn off wifi and mobile data, start the app and give it root permission.
-press the recovery update, select the chinese character file that you copied to your sd before and proceed, VERY IMPORTANT when it asks if you want to reboot into recovery select NO.
- get out off the app and restart your device normally, it's all done you have your phone back.
this is my first tutorial on xda, hope it is easy to follow and i'm thankfull for any suggestions to improve it.

Not rebooting automatically after fastboot continue command
sevenr33 said:
this tutorial, is for repairing the huawei g750-u10 in case you flashed the wrong recovery and now you're stuck in a bootloop.
First of all you will need (it's all in the link to download, make shure you have a sdcard on your phone before starting):
-Adb install setup
-Adb toolkit
-vcom drivers
mega.co.nz/#!gURHXDoZ!QNmv7LaK8r4WIQBGaUyoNho3TPX0YZp9jwHaEHgDmII
note:the recovery.img provided on the rar file only works for the U10, the method might work for other models but with a diferent recovery file.
-Installation of the phone mediatek drivers:
-Start with installing th vcom drivers i provided on the rar file, type HDWWIZ on the windows search tab:
Install the hardware manually>Ports(com&lpt)>Have a disk>select the file wich corresponds to you windows>mediatekpreloader usb vcom port> restart your computer. (if this method doesn't work for you try to search for vcom driver installation tutorials)
-Installing adb
-double click on the adb-setup.exe file provided and install it including drivers.
-the adb tool kit doesn't need installation just run the Adb toolkit Gui
on adb toolkit, type the command fastboot continue as shown in the picture
s13.postimg.org/yuauaawpj/Untitled.jpg
Remove the battery from your mobile phone, wait 5s plug it in again. Connect the usb to the computer and pluh it to your phone and at the same time push the power button till it turns on but keep your finger in the VOLUME DOWN all the time, it may reboot 2 times but then you will get the fastboot/repair mode image you can now lift your finger.
When you are in fastboot connected to your computer (the mediatek drivers will install wait for installation to complete).
Now return to the Adb GUI and press the execute command, (it will appear 3 lines starting with something saying error dont mind that it's normal) and wait a few seconds then your phone will restart it self and boot normally.
You're allmost there:
-When your phone boots, select the usb connection to usb mass storage device.
-copy the recovery.img provided to the root of your sdcard, safely unplug the phone from your pc.
-download and install the mobile mtk uncle tools app from the playstore.
-turn off wifi and mobile data, start the app and give it root permission.
-press the recovery update, select the chinese character file that you copied to your sd before and proceed, VERY IMPORTANT when it asks if you want to reboot into recovery select NO.
- get out off the app and restart your device normally, it's all done you have your phone back.
this is my first tutorial on xda, hope it is easy to follow and i'm thankfull for any suggestions to improve it.
Click to expand...
Click to collapse
Hi, I've followed the instructions you gave and now I'm stucked at the part which it wouldn't reboot by itself after i typed the "fastboot command".
1) Before I've had chance to charge my phone, it ran out of battery and fastboot mode does not charge the phone. I've also tried to flash the recovery image in fastboot mode, but i got Err:0x2017, what is this error about?
2) And the GUI should run in location bin files as my fastboot driver, not the 0KB fastboot in default location.
2) Do all these steps require unlocking bootloader? I don't think I've unlocked, all I did was just root the phone.

Help
Hi
I have a rooted Huawei Ascend Mate but I installed the wrong TWRP recovery a few days ago. My phone keeps booting and I can't use my recovery, because it is a touch version but it doesn't respond to my touch. So, I don't know if I can flash my stock rom or another recovery...
Can I use this tutorial to fix my phone or can you please make one for the Huawei Ascend Mate?
kind regards

[Completed] New Guide for rooting LG Volt(LGLS740)

This guide is for a brand new Boost Mobile LG Volt (LGLS740.) 4/4/2015
I had an LG Realm that I rooted in less than 5 minutes with Kingo Root. Cracked the screen, didn't have time to fix it so I went and bought the LG Volt from Boost Mobile. I've spent around 7 months trying to root the stupid thing with one-click utilities and other tricks and gave up.
Finally I found a guide that got me on the right path and made it happen. Now keep in mind I didn't have to flash back to earlier versions of firmware for anything you can do this on ZV5.
First download the attachment (LG_Root.zip) and unzip it too your desktop or wherever you wish.
make sure you have the LG_unified drivers installed(I did all this in Windows 7 but it shouldn't matter.)
And now I pass you off to this brilliant man's guide: http://forum.xda-developers.com/and...lg-devices-t3049772/post59309508#post59309508
It took me all of two minutes to root the phone. Don't be afraid. To sum it all up:
1. Install drivers, extract LG_root.
2. Make sure the usual is done(Enable USB debugging, allow untrusted vendors)
3. Hold shift and left click in the window to open command line in the proper directory
4. type adb.exe devices in the command window or just paste it from here, and make sure your device shows up.
5. copy and paste this to the command prompt: adb.exe push busybox /data/local/tmp/ && adb.exe push lg_root.sh /data/local/tmp && adb.exe push UPDATE-SuperSU-v2.46.zip /data/local/tmp which pushes the supersu utility to your phone.
6. a: Power off your device
b:When the device is powered off, hold volume up and insert a USB cable connected to the PC
c:Wait for the drivers to install
7. Double click ports.bat (This will give us the COM port in which our device is connected we are looking for the Diag port, mine was com4, com3 didn't even show up in mine so no worries.)
8. Go back to your command prompt window(close the Ports.bat window if you want.) and paste: Send_Command.exe \\.\COM4 (This opens the channel to send commands to the diag port.)
9. Paste this final command to your command prompt when the channel is open: sh /data/local/tmp/lg_root.sh dummy 1 /data/local/tmp/UPDATE-SuperSU-v2.46.zip /data/local/tmp/busybox
10. Once it's done you can pull the battery.
FYI: I had trouble a couple of times while in firmware mode and had to restart once or twice before I did it all correctly. Also, I know I'm just basically copying Unjustified_Dev's post but it took me around 7 or 8 months to find a way that worked with this phone so I just want it to be easier for people to find and confirm that it works for the LG Volt(LGLS740) when you try to find a way to root it. And NONE of the one click utilities worked for me.
Thanks everyone and especially Unjustified Dev, I hope this helps and brings some attention to this phone model. I remember I had a certain version of the Motorola Razr(V3XX) or something and I could barely ever get anything hacked with it, it was frustrating as hell!

PlasticCogLiquid said:
This guide is for a brand new Boost Mobile LG Volt (LGLS740.) 4/4/2015
I had an LG Realm that I rooted in less than 5 minutes with Kingo Root. Cracked the screen, didn't have time to fix it so I went and bought the LG Volt from Boost Mobile. I've spent around 7 months trying to root the stupid thing with one-click utilities and other tricks and gave up.
Finally I found a guide that got me on the right path and made it happen. Now keep in mind I didn't have to flash back to earlier versions of firmware for anything you can do this on ZV5.
First download the attachment (LG_Root.zip) and unzip it too your desktop or wherever you wish.
make sure you have the LG_unified drivers installed(I did all this in Windows 7 but it shouldn't matter.)
And now I pass you off to this brilliant man's guide: http://forum.xda-developers.com/and...lg-devices-t3049772/post59309508#post59309508
It took me all of two minutes to root the phone. Don't be afraid. To sum it all up:
1. Install drivers, extract LG_root.
2. Make sure the usual is done(Enable USB debugging, allow untrusted vendors)
3. Hold shift and left click in the window to open command line in the proper directory
4. type adb.exe devices in the command window or just paste it from here, and make sure your device shows up.
5. copy and paste this to the command prompt: adb.exe push busybox /data/local/tmp/ && adb.exe push lg_root.sh /data/local/tmp && adb.exe push UPDATE-SuperSU-v2.46.zip /data/local/tmp which pushes the supersu utility to your phone.
6. a: Power off your device
b:When the device is powered off, hold volume up and insert a USB cable connected to the PC
c:Wait for the drivers to install
7. Double click ports.bat (This will give us the COM port in which our device is connected we are looking for the Diag port, mine was com4, com3 didn't even show up in mine so no worries.)
8. Go back to your command prompt window(close the Ports.bat window if you want.) and paste: Send_Command.exe \\.\COM4 (This opens the channel to send commands to the diag port.)
9. Paste this final command to your command prompt when the channel is open: sh /data/local/tmp/lg_root.sh dummy 1 /data/local/tmp/UPDATE-SuperSU-v2.46.zip /data/local/tmp/busybox
10. Once it's done you can pull the battery.
FYI: I had trouble a couple of times while in firmware mode and had to restart once or twice before I did it all correctly. Also, I know I'm just basically copying Unjustified_Dev's post but it took me around 7 or 8 months to find a way that worked with this phone so I just want it to be easier for people to find and confirm that it works for the LG Volt(LGLS740) when you try to find a way to root it. And NONE of the one click utilities worked for me.
Thanks everyone and especially Unjustified Dev, I hope this helps and brings some attention to this phone model. I remember I had a certain version of the Motorola Razr(V3XX) or something and I could barely ever get anything hacked with it, it was frustrating as hell!
Click to expand...
Click to collapse
Because there is not a specific forum for your device, you can start your own thread here General Upgrading, Modifying and Unlocking

No reply, thread will be closed.

Reset lockscreen security on GoClever Tab r76.2

Hello, I get just today a GoClever Tab r76.2 to reset the forgotten pin from the locksreen. Device was used mainly for Pou and Facebook, so there was no root, no usb debugging, my PC was not set as trusted device, just like from the store with PIN set. Installed system is Android 4.1
Because it took me whole morning and I found a lot of answers that "it cannot be done, you have to factory reset" I want to show you my steps to make this process easier for people in need. This method shouldn't erase any data from your device but always remember to have a backup
It is based on the following tutorial: http://forum.xda-developers.com/showthread.php?t=2601933 , but still it was not enough for me so I want to provide more details.
Step 1.
The very important thing is to install drivers for the device. To make this process the easiest I get my old, good Asus netbook with Windows XP installed. You can install it also on VirtualMachine, it is not very mandatory but my next steps will be based on this configuration.
There is a need for two types of drivers: Rockchip drivers to flash the memory and ADB Drivers.
1.1) Rockchip drivers can be found in the thread linked above, I am providing mirror at the bottom of this thread. Just doubleclick on the exe, accept the risk and install, that's all for now.
1.2 ADB drivers are provided in the second package attached. To install adb drivers go to recovery.
To switch tablet to the Recovery Mode you have to switch it off (not reboot), turn it on, just when the BootScreen will appear tap Vol+ until you will see opened Android Robot with exclamation mark. What's interesting, when you double click Vol+ this time you can switch to Android Recovery menu and factory reset the device
In device manager (Win+R, type: devmgmt.msc and press ENTER) install drivers for Tab r76 device manually, by providing direct location to the .ini file from the folder.
Leave tablet in Recovery.
Step 2.
People from some Russian Android forum prepared package with pre-configured adb for rockchip devices. Just download attachment 2.1, extract it, install, open Command Line and "cd" to directory with adb.exe, very useful.
Step 3.
Now we will root the device and install CWM. Download file from the attachment 3.1, unzip it and run "RK29Update.exe", don't click any button (especially the one called "Erase", it will brick your device), don't change any setting, your tablet will be not found at the moment. This package belongs to the author of the original tutorial.
Step 4.
In command line enter "adb devices" to check if your tablet is visible, you should see something like "0123456789ABCDEF recovery", if yes enter "adb reboot bootloader" and press enter. Tablet will reboot, the screen will remain black, system will install the Rockchip driver, RK29Update.exe will find the device (IF NOT just reboot to recovery again and reboot to bootloader from adb again, driver installation might interrupt this process), press Run button in the application it will flash the device with root patch and CWM, device will reboot to CWM recovery.
Step 5.
Download attachment nr 5.1 (original source: http://forum.xda-developers.com/showthread.php?t=2437946) and put the zip to the SD card (card has to be compatible with the device - most secure solution is having FAT32 filesystem), put it to the tablet, install zip from external source (not sdcard, it's internal memory).
After reboot of the device ("restart system now" option in main page of CWM) your device should welcome you without screen locked by any security possible and your settings should remain untouched.
From now everybody should be able to reset it's PIN in the easy way Have fun
CC: You are allowed to copy this tutorial anywhere, mirror the links also, but please leave a link to the original thread.

GCam Without Root & Without Flashing Twrp

To continue this process you need to unlock your bootloader.
Read the full thread before doing anything.
1. Download Platform Tools & Extract it: https://dl.google.com/android/repository/platform-tools-latest-windows.zip
2. Copy the twrp file for your device into the extracted folder.
Latest Twrp for RN5Pro(Whyred): https://dl.twrp.me/whyred/
after downloading twrp rename it to twrp.img
3. Turn on Usb Debugging on your device and Connect the phone to the usb cable
4. Now open the platform tools folder and in the address section type cmd & hit enter
5. Type commands:
(a) adb reboot bootloader & hit enter(phone is now in fastboot mode)
(b) fastboot boot twrp.img
twrp mode is now open....just touch on keep read only(don't do anything you still now in twrp mode)
(c) adb devices (check your device is connected or not)
(d) adb shell
(e) setprop persist.camera.HAL3.enabled 1 ( be careful while typing or copy paste this line)
(f) exit
(g) adb reboot( your phone will Reboot now)
If gcam force closes then reboot your phone manually.
Done.I am not responsible if you brick your device.
#Now download GCam from below the link and install it.
In this method we doesn't flash twrp we are just boot into twrp to enable camera 2 api
Download GCam :
https://www.celsoazevedo.com/files/android/google-camera/f/GoogleCamera-Pixel2Mod-Arnova8G2-V8.apk
Official GCam Link : https://www.celsoazevedo.com/files/android/google-camera/
If you're not sure how this process is done then contact me in my email address : [email protected]
Thank You

I don't see the point in booting to twrp. All you need to do is to boot into fastboot and apply the adb commands.

anon768 said:
I don't see the point in booting to twrp. All you need to do is to boot into fastboot and apply the adb commands.
Click to expand...
Click to collapse
I think you can't access ADB in fastboot.

anon768 said:
I don't see the point in booting to twrp. All you need to do is to boot into fastboot and apply the adb commands.
Click to expand...
Click to collapse
try this method then you will see how it works.

Hosssain said:
I think you can't access ADB in fastboot.
Click to expand...
Click to collapse
Bro try the method,I am using GCam through this process.

hmmmn
I'm kinda lost here, what i have to do?
imgu r. com/a/FTfelHt

Rumcyk said:
I'm kinda lost here, what i have to do?
imgu r. com/a/FTfelHt
Click to expand...
Click to collapse
email me bro..my email id is already is given... follow the thread

is it work for redmi note 5 AI

does not work. It says "The system has been destroyed" and reboot into system after few seconds.

[email protected] said:
does not work. It says "The system has been destroyed" and reboot into system after few seconds.
Click to expand...
Click to collapse
)))))))))

Worked for me
I had to unlock the bootloader to follow this method.
First I got the system destroyed message, when I did with the bootloader locked.
Gcam that you suggested didn't work well for me. Then I used another one instead. Now everything is functioning properly.

Not working on my friends locked phone. It is showing "system destroyed".

You'll need to root and set Selinux to permissive because this will make your stock camera lag like hell

Work or not work?

Is the quality of the photos the same thing that happens with the other methods?
is it true that with this method, the quality of the camera gets worse?

the photo quality good better than stock app.
but the issue use gcam cant save front camera with hdr+ active

even with the miui 10 okay?

help
RSubha said:
Bro try the method,I am using GCam through this process.
Click to expand...
Click to collapse
I have heard that in miui10 global stable rom,after enabling camera2api without rooting,front camera is broken in third party apps like whatsapp...Is it true???

RSubha said:
To continue this process you need to unlock your bootloader.
Read the full thread before doing anything.
1. Download Platform Tools & Extract it: https://dl.google.com/android/repository/platform-tools-latest-windows.zip
2. Copy the twrp file for your device into the extracted folder.
Latest Twrp for RN5Pro(Whyred): https://dl.twrp.me/whyred/
after downloading twrp rename it to twrp.img
3. Turn on Usb Debugging on your device and Connect the phone to the usb cable
4. Now open the platform tools folder and in the address section type cmd & hit enter
5. Type commands:
(a) adb reboot bootloader & hit enter(phone is now in fastboot mode)
(b) fastboot boot twrp.img
twrp mode is now open....just touch on keep read only(don't do anything you still now in twrp mode)
(c) adb devices (check your device is connected or not)
(d) adb shell
(e) setprop persist.camera.HAL3.enabled 1 ( be careful while typing or copy paste this line)
(f) exit
(g) adb reboot( your phone will Reboot now)
If gcam force closes then reboot your phone manually.
Done.I am not responsible if you brick your device.
#Now download GCam from below the link and install it.
In this method we doesn't flash twrp we are just boot into twrp to enable camera 2 api
Download GCam :
https://www.celsoazevedo.com/files/android/google-camera/f/GoogleCamera-Pixel2Mod-Arnova8G2-V8.apk
Official GCam Link : https://www.celsoazevedo.com/files/android/google-camera/
If you're not sure how this process is done then contact me in my email address : [email protected]
Thank You
Click to expand...
Click to collapse
Which gcam should i use to front camera work correctly without patches on ai dual camera version ?

Front camera doesnt work with hdr on, or portreit mod, on any gcam i tried on rn5 whyred, sorry.