I am using moto g3 x1550. A few months ago my scree was broken and make it replaced but it was not original. But it work perfect on L.P (5.0) based ROM but when I install M.M (6.0) based ROM touch does not work as from the starting from the language setup but only volume and power key are working and also display but not touch...
Plzzz help me up.
If your screen isnt original then chances are your device will be rejected to be serviced at moto center.
edit : http://forum.xda-developers.com/showpost.php?p=66002023&postcount=1262 try flashing these zip files and see if your touch screen is back.
Else you can try downgrading to lollipop or reflashing stock MM images and see if your touch screen is working. Use this linkhttp://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750 to flash stock images. Note: data loss might occur backup data that is important.
vimjam said:
If your screen isnt original then chances are your device will be rejected to be serviced at moto center.
edit : http://forum.xda-developers.com/showpost.php?p=66002023&postcount=1262 try flashing these zip files and see if your touch screen is back.
Else you can try downgrading to lollipop or reflashing stock MM images and see if your touch screen is working. Use this linkhttp://forum.xda-developers.com/2015-moto-g/general/guide-fastboot-flashing-factory-t3187750 to flash stock images. Note: data loss might occur backup data that is important.
Click to expand...
Click to collapse
Is it safe. I mean that my phone could get had brick or permanently touch not work after flashing that file.
Sorry for bad English?
Piyush Garg said:
Is it safe. I mean that my phone could get had brick or permanently touch not work after flashing that file.
Sorry for bad English
Click to expand...
Click to collapse
hmm this can also be a hardware problem as the touchscreen in not generic and we do not know how it will react to the drivers, so noting cannot be guaranteed. Your best bet is to take a leap of faith and flash the zip, if it fails you can always return to lollipop roms.
That flashable zip just replaces touch drivers not the entire rom. Besides that flashable zip was created by Alberto97 who brought us CM13 so i highly doubt that flashable zip will brick your phone.
But none the less if you truly want a fail safe procedure your best bet is moto service.
p.s no one at xda is responsible for anything happening to any device as this is a community not a paid service where we are responsible for our work.
vimjam said:
hmm this can also be a hardware problem as the touchscreen in not generic and we do not know how it will react to the drivers, so noting cannot be guaranteed. Your best bet is to take a leap of faith and flash the zip, if it fails you can always return to lollipop roms.
That flashable zip just replaces touch drivers not the entire rom. Besides that flashable zip was created by Alberto97 who brought us CM13 so i highly doubt that flashable zip will brick your phone.
But none the less if you truly want a fail safe procedure your best bet is moto service.
p.s no one at xda is responsible for anything happening to any device as this is a community not a paid service where we are responsible for our work.
Click to expand...
Click to collapse
Which one should be flashed.
Now I am using cm12.1 so can I flash these zip in it or first I flash cm13 and and flash these zip.
And if pH get brick then will it be hard brick or soft..
thanks :thumbup:
Piyush Garg said:
Which one should be flashed.
Now I am using cm12.1 so can I flash these zip in it or first I flash cm13 and and flash these zip.
And if pH get brick then will it be hard brick or soft..
thanks :thumbup:
Click to expand...
Click to collapse
if it gets bricked it will be soft brick , you can go to twrp wipe & flash cm again. these drivers are for cm13 so you need to flash after cm13 is flashed or along with cm13.
the first zip is to restore to older stable drivers , so flash this first . If the touch screen didn't improve flash the second one to restore to default drivers.
Im facing too.. Try BrokenOS.. No issues in that rom!
vimjam said:
if it gets bricked it will be soft brick , you can go to twrp wipe & flash cm again. these drivers are for cm13 so you need to flash after cm13 is flashed or along with cm13.
the first zip is to restore to older stable drivers , so flash this first . If the touch screen didn't improve flash the second one to restore to default drivers.
Click to expand...
Click to collapse
Same problem touch is not working
After flashing both file..of drivers
Piyush Garg said:
Same problem touch is not working
After flashing both file..of drivers
Click to expand...
Click to collapse
Touch issue is an hardware related problem. Motorola IT say me that IT is an hardware problem exasperated by MM update (and related synaptics drivers).
Imho it is due by bad grounded IC or by the glue used to bind the LCD at motherboard
IMP_IT said:
Touch issue is an hardware related problem. Motorola IT say me that IT is an hardware problem exasperated by MM update (and related synaptics drivers).
Imho it is due by bad grounded IC or by the glue used to bind the LCD at motherboard
Click to expand...
Click to collapse
Yes I had changed my whole screen and it is duplicate.
Is there is any way to solve this problem plzzz plzzz held..
Piyush Garg said:
Yes I had changed my whole screen and it is duplicate.
Is there is any way to solve this problem plzzz plzzz held..
Click to expand...
Click to collapse
yes. Try this
https://www.dropbox.com/s/jemv0yqjf9m25vm/IMG_20160319_154102989.jpg?dl=0
https://www.dropbox.com/s/dc2pgzrc2lcdnf8/IMG_20160319_154042223.jpg?dl=0
IMP_IT said:
yes. Try this
https://www.dropbox.com/s/jemv0yqjf9m25vm/IMG_20160319_154102989.jpg?dl=0
https://www.dropbox.com/s/dc2pgzrc2lcdnf8/IMG_20160319_154042223.jpg?dl=0
Click to expand...
Click to collapse
How to use this
Piyush Garg said:
Yes I had changed my whole screen and it is duplicate.
Is there is any way to solve this problem plzzz plzzz held..
Click to expand...
Click to collapse
Piyush Garg said:
How to use this
Click to expand...
Click to collapse
it's black humour but it also demonstrate that there is an hw problem. If you try to put an aluminium foil in back cover of your moto g the touch issue disappears completely. But it also may modify SAR values, reception etc...
But, I say try it so you can see that problem disappear.
IMP_IT said:
it's black humour but it also demonstrate that there is an hw problem. If you try to put an aluminium foil in back cover of your moto g the touch issue disappears completely. But it also may modify SAR values, reception etc...
But, I say try it so you can see that problem disappear.
Click to expand...
Click to collapse
My problem will disappear or my phone?
IMP_IT said:
it's black humour but it also demonstrate that there is an hw problem. If you try to put an aluminium foil in back cover of your moto g the touch issue disappears completely. But it also may modify SAR values, reception etc...
But, I say try it so you can see that problem disappear.
Click to expand...
Click to collapse
Is this really work..
Piyush Garg said:
Same problem touch is not working
After flashing both file..of drivers
Click to expand...
Click to collapse
Piyush Garg said:
Is this really work..
Click to expand...
Click to collapse
Yes it really work but it s not reccomanded
IMP_IT said:
Yes it really work but it s not reccomanded
Click to expand...
Click to collapse
Why??
Piyush Garg said:
Why??
Click to expand...
Click to collapse
Because can modify SAR values and the exposition of body to EM fields
IMP_IT said:
Because can modify SAR values and the exposition of body to EM fields
Click to expand...
Click to collapse
So what problem would I face
Have u tryed it or saw someone doing this
Piyush Garg said:
So what problem would I face
Have u tryed it or saw someone doing this
Click to expand...
Click to collapse
No problem. I tried this. I 'invented' this lol.
Try once it does not cause anithing except different irradiation by EM fields
Related
greeting
i have a huge problem from my optimus one, touch screen not working at all
after i flash rom like dynamite (20i) and then i reboot and flash thunderg kernel v 1 (tha) and stuck in LG logo. then I did a hard reset. wipe all and flash rom 20i. everthing is work, from booting up to go to the start screen rom. i try to touch android image but i cant
i try flash another rom like pp 2.3 or nfe 4.6 but still same
maybe it seems like aspee problem
http://forum.xda-developers.com/showthread.php?t=1377039
any idea what to do?
so there is no choice? should i go to lg service center?
greet
go to lg service center
> it also happened to me once.. flashing rom changing kernels.. still touch screen doesnt respond.. what i did just leave it for an hour or two.. the screen works again.. really weird though
Go to service center bro.. hope u still under warranty
neko95 said:
> it also happened to me once.. flashing rom changing kernels.. still touch screen doesnt respond.. what i did just leave it for an hour or two.. the screen works again.. really weird though
Click to expand...
Click to collapse
Try that first before going to a service centre. Seriously, might actually solve your problem xD. I'd recommend removing the battery though and leaving it for about a day. If that doesn't solve your problem then LG Centre, or a new phone?
Have you tried calibrating the screen?
Create a file called "calibration.ini" and stick it in the root of your SD card.
Reboot and don't touch the screen until your OS is fully loaded. Then, delete calibration.ini and reboot again.
okay, thanks for your attention
Try to flash an original rom!
Flash 2.2 kdz and you will got touchscreen working
Guaranteed
Sent from my LG-P500 using xda premium
KDZ? okay
I try when I get home
update :
it's works!! thanks aspee
50n3 said:
KDZ? okay
I try when I get home
update :
it's works!! thanks aspee
Click to expand...
Click to collapse
Wow! KDZ saved my life, Thanks!
Touchscreen not working after flashing dynamite rom
aspee said:
Flash 2.2 kdz and you will got touchscreen working
Guaranteed
Sent from my LG-P500 using xda premium
Click to expand...
Click to collapse
Hey,
I too faced this problem and then i found this post..
Really KDZ saved my life...
You are great.
Thank u sooooo much.
Had the same problem!
I didn't tried to use KDZ (since it takes a lot of time to configure stuff...).
I solved the problem by flashing http://forum.xda-developers.com/showthread.php?t=1574523
theanykey said:
Have you tried calibrating the screen?
Create a file called "calibration.ini" and stick it in the root of your SD card.
Reboot and don't touch the screen until your OS is fully loaded. Then, delete calibration.ini and reboot again.
Click to expand...
Click to collapse
Thanks a lot! :victory:
I have 2 of the same phone mt6575. One of them wont work i think it is bricked. Is there anyway to take whats on the other phone say the rom and such to fix the broken one. Thanks
SteelGluer said:
I have 2 of the same phone mt6575. One of them wont work i think it is bricked. Is there anyway to take whats on the other phone say the rom and such to fix the broken one. Thanks
Click to expand...
Click to collapse
Maybe processor is the same, but idc files and touch features would be different and don't work, but you can try installing a recovery in fuctional device, and flashing a backup in non-working device.
josalaito said:
Maybe processor is the same, but idc files and touch features would be different and don't work, but you can try installing a recovery in fuctional device, and flashing a backup in non-working device.
Click to expand...
Click to collapse
Not sure what ya mean. Recovery in functional.
Hello,i turn of my phone and after 2 hours i open it. From that moment my phone crashes ( freeze ) all the time and restart itself,i already change rom i flashed "A850_23.10.2013_RUS_by_linerty" and "A850-Stock-S123" but nothing happend,what can i do ???
dinossp said:
Hello,i turn of my phone and after 2 hours i open it. From that moment my phone crashes ( freeze ) all the time and restart itself,i already change rom i flashed "A850_23.10.2013_RUS_by_linerty" and "A850-Stock-S123" but nothing happend,what can i do ???
Click to expand...
Click to collapse
If you have flash those roms without installing anything and you always have that problem, then i sounds like a hardware problem...
GreatApo said:
If you have flash those roms without installing anything and you always have that problem, then i sounds like a hardware problem...
Click to expand...
Click to collapse
yes i think that too.
do you know if i can find parts ( like mtk chip) in market?
dinossp said:
yes i think that too.
do you know if i can find parts ( like mtk chip) in market?
Click to expand...
Click to collapse
If you have the phone less than 6 months you can contact your Chinese seller (but be careful with the day because if the 6 months pass they will not replace it + you will be charged with the mail).
I am not a Phone Engineer so i can't help you change your chips (and you do not know if that is the problem...), plus, do you have the equipment to do so?
If i where you i would try a local phone repair shop, ask for the charge and decide if you want to fix it or take a new phone.
ok maybe i will repair my phone in local shop.
thank a lot for reply :good:
could be kernel's problem??? (i dont know much about kernel)
dinossp said:
could be kernel's problem??? (i dont know much about kernel)
Click to expand...
Click to collapse
I do not thing so... there are not custom kernels for our phone yet and i am not sure but flash tool may flash that too.
GreatApo said:
I do not thing so... there are not custom kernels for our phone yet and i am not sure but flash tool may flash that too.
Click to expand...
Click to collapse
i solve the problem.
a smd from audio jack circuit was dead i just removed and my phone is back to life now (my audio jack is dead but i will try to fix it as soon as possible).
thanks again for your help :good:
dinossp said:
i solve the problem.
a smd from audio jack circuit was dead i just removed and my phone is back to life now (my audio jack is dead but i will try to fix it as soon as possible).
thanks again for your help :good:
Click to expand...
Click to collapse
hi dinossp,
could you give me more details on how you fix the phone?
i have the same problem and not fixed yet. i had changed to other rom but still no luck.
it keeps freezing and restarting
thank you
My device would always restart
I know my device right
No untying
I found a problem
Why is he doing restart
I am with this rom
It works fine all is not doing a restart
When I install another rom problem begins to restart stuck
Example Hammerhead v1.8 installed BlissPop
And much rom it to the same problem
Why is this happening? Really strange problem
There is a solution? Know why this happens?
Sorry for my bad English
haimmalka said:
My device would always restart
I know my device right
No untying
I found a problem
Why is he doing restart
I am with this rom
It works fine all is not doing a restart
When I install another rom problem begins to restart stuck
Example Hammerhead v1.8 installed BlissPop
And much rom it to the same problem
Why is this happening? Really strange problem
There is a solution? Know why this happens?
Sorry for my bad English
Click to expand...
Click to collapse
did you follow all instructions for the new rom install properly? its some problem with the rom. Try a new rom and make sure you follow all the instructions properly
rollerdyke44 said:
did you follow all instructions for the new rom install properly? its some problem with the rom. Try a new rom and make sure you follow all the instructions properly
Click to expand...
Click to collapse
I do it right
wipe
Then install rom
There rom works
Some do not work to restart always get stuck
I wonder why
haimmalka said:
My device would always restart
I know my device right
No untying
I found a problem
Why is he doing restart
I am with this rom
It works fine all is not doing a restart
When I install another rom problem begins to restart stuck
Example Hammerhead v1.8 installed BlissPop
And much rom it to the same problem
Why is this happening? Really strange problem
There is a solution? Know why this happens?
Sorry for my bad English
Click to expand...
Click to collapse
If nothing else works flash a factory image ☺
sachin.parmar100 said:
If nothing else works flash a factory image
Click to expand...
Click to collapse
What you seem I do not understand?
haimmalka said:
What you seem I do not understand?
Click to expand...
Click to collapse
I meant if any other methods doesn't work then grab a factory image via Google server and flash it via fastboot
Link :
https://developers.google.com/android/nexus/images
sachin.parmar100 said:
I meant if any other methods doesn't work then grab a factory image via Google server and flash it via fastboot
Link :
https://developers.google.com/android/nexus/images
Click to expand...
Click to collapse
I understood but I ask why this is happening
Some of the works
And some do not work restart
I want to know what the problem is
Probably kernel issue.
Aerowinder said:
Probably kernel issue.
Click to expand...
Click to collapse
Explain what this means?
haimmalka said:
Explain what this means?
Click to expand...
Click to collapse
Google it
dicecuber said:
Google it
Click to expand...
Click to collapse
Hahaha
I looked it up on Google
I went back to the same state device always do a restart
Until it worked fine now again it came back to do it] =
I was looking google what he means I get here:
http://kernels.franco-lnx.net/Nexus5/5.0/
Then again it returned to constantly restart the device
Now there is a direction to know how it happens?
How to fix it?
I do not remember what I did that worked
Tip know at least that's how it happens:crying:
haimmalka said:
Explain what this means?
Click to expand...
Click to collapse
A kernel acts as a connection between the
hardware and the software.
so if you flash a wrong kernel, it will misbehave
sachin.parmar100 said:
A kernel acts as a connection between the
hardware and the software.
so if you flash a wrong kernel, it will misbehave
Click to expand...
Click to collapse
I think that's a problem for the solution of the fire makes it
I order the same day repair lab
Flash a factory image. If the restarts stop then you know it's a problem with the ROM/kernel. Not all phones are identical, what may work for some doesn't always work for others. Your phone simply may not like some custom kernels, simple as that. If the ones you are flashing are undervolted by default that could be the problem, as some phones respond better to undervolting than others.
_MetalHead_ said:
Flash a factory image. If the restarts stop then you know it's a problem with the ROM/kernel. Not all phones are identical, what may work for some doesn't always work for others. Your phone simply may not like some custom kernels, simple as that. If the ones you are flashing are undervolted by default that could be the problem, as some phones respond better to undervolting than others.
Click to expand...
Click to collapse
Happens all the time for my device
I also install this rom Original still to helping through Toolkit
I also put a device
Start-up Shutdown button repair
It did not help thinking maybe this is the problem
So what is the problem I can not figure] =
haimmalka said:
Happens all the time for my device
I also install this rom Original still to helping through Toolkit
I also put a device
Start-up Shutdown button repair
It did not help thinking maybe this is the problem
So what is the problem I can not figure] =
Click to expand...
Click to collapse
Don't use toolkits. Flash the system image with fastboot. If the problem is still there, it's your phone. If the problem disappears, it's the ROM/kernel. Again, use fastboot and not a toolkit.
_MetalHead_ said:
Don't use toolkits. Flash the system image with fastboot. If the problem is still there, it's your phone. If the problem disappears, it's the ROM/kernel. Again, use fastboot and not a toolkit.
Click to expand...
Click to collapse
I try many things to no avail
I put it back to the lab to solve this problem
I've had enough to deal with it without success..
I do not know if it's a software problem
Or issue with the device
I do not believe more than 5 Nexus device that happens to many people
haimmalka said:
I try many things to no avail
I put it back to the lab to solve this problem
I've had enough to deal with it without success..
I do not know if it's a software problem
Or issue with the device
I do not believe more than 5 Nexus device that happens to many people
Click to expand...
Click to collapse
But have you restored to 100% stock by flashing a factory image using fastboot?
_MetalHead_ said:
But have you restored to 100% stock by flashing a factory image using fastboot?
Click to expand...
Click to collapse
I do not understand exactly what you record
I can not understand English I use Google Translate
Thank you you try to help
You need to tell me what to do to try ..
I just try it
Guide me step by step what to do
If you ask yes I have fastboot
Files
flash-all
image-hammerhead-ktu84p
bootloader-hammerhead-hhz11k
radio-hammerhead-m8974a-2.0.50.2.22
image-hammerhead-krt16m
cache
boot
bootloader-hammerhead-HHZ11d
userdata
system
recovery
I press
flash-all
Command window opens install it
It does not help
I also make it a manual command that does not help
I try a lot of versions
This is repeated restart problem ]=
Hey, I have got a problem with my OnePlus One for quiet some time..
It started about 2 months ago - Whenever I'm on a call, the other side can barely hear me unless I'm on speaker.
I did some reading and there are suggestions that this is because of some mis-written code or something, that makes the input of the microphone low, so that only a small precent of the sound is being transferred to the one I'm talking to.
this may or may not be the problem, but I wanted to ask you fellows if anyone has any suggestion on what's causing this and how to try & solve it.
I'm Running a Stock 5.0.2 Cm12s with the latest OTA update, and this problem started when I had Stock 4.4.4 CM11s.
Device isn't rooted & never was.
Locked Bootloader.
Please help if you can
Lidor167 said:
Hey, I have got a problem with my OnePlus One for quiet some time..
It started about 2 months ago - Whenever I'm on a call, the other side can barely hear me unless I'm on speaker.
I did some reading and there are suggestions that this is because of some mis-written code or something, that makes the input of the microphone low, so that only a small precent of the sound is being transferred to the one I'm talking to.
this may or may not be the problem, but I wanted to ask you fellows if anyone has any suggestion on what's causing this and how to try & solve it.
I'm Running a Stock 5.0.2 Cm12s with the latest OTA update, and this problem started when I had Stock 4.4.4 CM11s.
Device isn't rooted & never was.
Locked Bootloader.
Please help if you can
Click to expand...
Click to collapse
try to flash this http://forum.xda-developers.com/oneplus-one/development/fix-low-mic-call-t3055661
I had the same problem and it fixed it.
The only thing is that i had to flash it after every rom change.
solokiller11 said:
try to flash this http://forum.xda-developers.com/oneplus-one/development/fix-low-mic-call-t3055661
I had the same problem and it fixed it.
The only thing is that i had to flash it after every rom change.
Click to expand...
Click to collapse
Does it not require a root access?
Lidor167 said:
Does it not require a root access?
Click to expand...
Click to collapse
it requires a custom recovery but not sure about root, i guess its required but not sure
solokiller11 said:
it requires a custom recovery but not sure about root, i guess its required but to sure
Click to expand...
Click to collapse
I don't even know what costum recovery means..
Lidor167 said:
I don't even know what costum recovery means..
Click to expand...
Click to collapse
read this thread, its a great one and explains everything you need to know
http://forum.xda-developers.com/oneplus-one/general/guides-bacon-timmaaas-how-to-guides-t2839471
you don't have to read everything (although recommended)
solokiller11 said:
read this thread, its a great one and explains everything you need to know
http://forum.xda-developers.com/oneplus-one/general/guides-bacon-timmaaas-how-to-guides-t2839471
you don't have to read everything (although recommended)
Click to expand...
Click to collapse
So in order to install a custom recovery ( say TWRP ) I do not need root acess? do I only need to follow step no.2 at the guide you gave me?
Lidor167 said:
I don't even know what costum recovery means..
Click to expand...
Click to collapse
Lidor167 said:
So in order to install a custom recovery ( say TWRP ) I do not need root acess? do I only need to follow step no.2 at the guide you gave me?
Click to expand...
Click to collapse
Yes, But it is also recommended to root the phone. Root is a great thing to have