Related
I have already tried this guide (great info there):
http://forum.xda-developers.com/one...fs-corrupt-t2879061/post55488755#post55488755
Unfortunately, it didn't quite work out for me. The issue I have been having is that the phone reports unknown baseband version and there is no IMEI. Wifi was still working originally. The issues came after I flashed the latest lollipop alpha modem needed for the latest CM12 build/kernel.
After I experienced the issue, I flashed back the 44s modem. Then Wifi was also gone.
As of right now, the best I can do is:
1. Install ColorOS 2.0.0
2. OTA to ColorOS 2.0.4
ColorOS gave me Wifi back.
At this point, I tried to fastboot install TWRP per @NikoZBK suggested. The fastboot command reported successful but it still got the ColorOS recovery. So I have to...
3. Fastboot flash 30o with flash-all.bat
However, by doing so, my Wifi is gone and I still have unknown baseband version and IMEI. Therefore, I went back to (1) and (2), took out this line: fastboot flash modem NON-HLOS.bin in flash-all.bat and run flash-all.bat again.
At this point, Wifi is still working but I still have unknown baseband version and IMEI.
4. Flash pre-rooted 44s in TWRP. The issues are still there.
I also tried doing "make_ext4fs /dev/block/mmcblk0p15" in TWRP and it actually killed Wifi. I am running out of ideas. Any advice is appreciated. Thanks!
radium22 said:
I have already tried this guide (great info there):
http://forum.xda-developers.com/one...fs-corrupt-t2879061/post55488755#post55488755
Unfortunately, it didn't quite work out for me. The issue I have been having is that the phone reports unknown baseband version and there is no IMEI. Wifi was still working originally. The issues came after I flashed the latest lollipop alpha modem needed for the latest CM12 build/kernel.
After I experienced the issue, I flashed back the 44s modem. Then Wifi was also gone.
As of right now, the best I can do is:
1. Install ColorOS 2.0.0
2. OTA to ColorOS 2.0.4
ColorOS gave me Wifi back.
At this point, I tried to fastboot install TWRP per @NikoZBK suggested. The fastboot command reported successful but it still got the ColorOS recovery. So I have to...
3. Fastboot flash 30o with flash-all.bat
However, by doing so, my Wifi is gone and I still have unknown baseband version and IMEI. Therefore, I went back to (1) and (2), took out this line: fastboot flash modem NON-HLOS.bin in flash-all.bat and run flash-all.bat again.
At this point, Wifi is still working but I still have unknown baseband version and IMEI.
4. Flash pre-rooted 44s in TWRP. The issues are still there.
I also tried doing "make_ext4fs /dev/block/mmcblk0p15" in TWRP and it actually killed Wifi. I am running out of ideas. Any advice is appreciated. Thanks!
Click to expand...
Click to collapse
Give this thread a look:http://forum.xda-developers.com/oneplus-one/help/opo-efs-t2821020. Look at page 9 and post 83. I don't know if it will help with your problem, but it fixed mine a few months back.
elrey311 said:
Give this thread a look:http://forum.xda-developers.com/oneplus-one/help/opo-efs-t2821020. Look at page 9 and post 83. I don't know if it will help with your problem, but it fixed mine a few months back.
Click to expand...
Click to collapse
Thanks for the info. I tried that but didn't work out for me unfortunately.
Finally, the issue is fixed!!! Here is what I have done:
1. fastboot flash 22R
2. reboot (No Wifi, No IMEI, Unknown Baseband version)
3. fastboot flash TWRP
4. reboot (Still No Wifi, No IMEI, Unknown Baseband version)
5. Download and copy OnePlus ColorV2.0.4i Beta Native.zip to internal
6. reboot to TWRP and flash OnePlus ColorV2.0.4i Beta Native.zip
7. reboot
8. Wifi, IMEI, mobile data, and baseband version are BACK!
radium22 said:
Finally, the issue is fixed!!! Here is what I have done:
1. fastboot flash 22R
2. reboot (No Wifi, No IMEI, Unknown Baseband version)
3. fastboot flash TWRP
4. reboot (Still No Wifi, No IMEI, Unknown Baseband version)
5. Download and copy OnePlus ColorV2.0.4i Beta Native.zip to internal
6. reboot to TWRP and flash OnePlus ColorV2.0.4i Beta Native.zip
7. reboot
8. Wifi, IMEI, mobile data, and baseband version are BACK!
Click to expand...
Click to collapse
Where did you find this 'OnePlus ColorV2.0.4i Beta Native.zip' file?
Vleiss said:
Where did you find this 'OnePlus ColorV2.0.4i Beta Native.zip' file?
Click to expand...
Click to collapse
can u pls share this file if u find it..?
OnePlus ColorV2.0.4i Beta Native.zip
I tried all methods, delete modemst1 and modemst2. Flash coloros manually, write imei with QPST (With this method regained imei but no signal and information is provided "radio off" and I can not find networks manually. I tried almost everything and can not get anything, just wi-fi. Someone having a backup of efs ?? or qcn?? , if you do not want to share the imei, blur the line 550, i need a backup of a running device., I will not clone or anything, I just need to repair my data qcn as there are 6468 and only have 5 lines with values.
rombdeta said:
I tried all methods, delete modemst1 and modemst2. Flash coloros manually, write imei with QPST (With this method regained imei but no signal and information is provided "radio off" and I can not find networks manually. I tried almost everything and can not get anything, just wi-fi. Someone having a backup of efs ?? or qcn?? , if you do not want to share the imei, blur the line 550, i need a backup of a running device., I will not clone or anything, I just need to repair my data qcn as there are 6468 and only have 5 lines with values.
Click to expand...
Click to collapse
I think its illegal to share these kind of information. I might be wrong though.
I know that you will not clone the IMEI but its against the rules to share this info.
Someone will be able to help you, I guess!!!
rombdeta said:
I tried all methods, delete modemst1 and modemst2. Flash coloros manually, write imei with QPST (With this method regained imei but no signal and information is provided "radio off" and I can not find networks manually. I tried almost everything and can not get anything, just wi-fi. Someone having a backup of efs ?? or qcn?? , if you do not want to share the imei, blur the line 550, i need a backup of a running device., I will not clone or anything, I just need to repair my data qcn as there are 6468 and only have 5 lines with values.
Click to expand...
Click to collapse
Shankar9822 said:
I think its illegal to share these kind of information. I might be wrong though.
I know that you will not clone the IMEI but its against the rules to share this info.
Someone will be able to help you, I guess!!!
Click to expand...
Click to collapse
Hi, @rombdeta, unfortunately for you @Shankar9822 is right, nobody can share their EFS backup with you. It's up to each user to backup their own EFS partition for safekeeping, this information is readily available all over this device section on XDA and on the OnePlus forums.
Transmitted via Bacon
Okay, you are right, i understend. But QCN, is different, have a parameters of the network. Is only that i need, because i have repaired imxx, wifi, bluetooth, but in the radio signal i have 0 dbm 99 asu, because i haven't the radio band who is in the QCN, and the information on this. If i can repair that, i will make a guide to recover imei without a EFS backup, so please help me with the QCN. Best regards.
After 10 days without the phone, and read about QCN in many sites and much info, i repair my device. For anyone who has tried all possible solutions, to no avail, they sent me a message, I will gladly help you. But I can't open a guide as I have understood, so this is the only solution I can currently provide. Thanks everyone. Greetings To You!
rombdeta said:
After 10 days without the phone, and read about QCN in many sites and much info, i repair my device. For anyone who has tried all possible solutions, to no avail, they sent me a message, I will gladly help you. But I can't open a guide as I have understood, so this is the only solution I can currently provide. Thanks everyone. Greetings To You!
Click to expand...
Click to collapse
If you're going to help people please don't do it via PM, do it here in the forums, solutions don't benefit the community when they're hidden away in an inbox.
Transmitted via Bacon
Ok, i will make a guide. OnePlus people told me they have no redress for the device, so I started reading and researching and with the help of many people, I put together a QCN with valid values, hand made in RF NV Item Manager. Therefore sought an original QCN. Tomorrow i will make a full guide. Regards and sorry about my english.
Thanks, good idea.
PS. There's nothing wrong with your English.
rombdeta said:
Ok, i will make a guide. OnePlus people told me they have no redress for the device, so I started reading and researching and with the help of many people, I put together a QCN with valid values, hand made in RF NV Item Manager. Therefore sought an original QCN. Tomorrow i will make a full guide. Regards and sorry about my english.
Click to expand...
Click to collapse
Do you have 2g (gsm only) and 3g/2g auto mode ? ( you probably dont need 2g but some do).
rombdeta said:
Okay, you are right, i understend. But QCN, is different, have a parameters of the network. Is only that i need, because i have repaired imxx, wifi, bluetooth, but in the radio signal i have 0 dbm 99 asu, because i haven't the radio band who is in the QCN, and the information on this. If i can repair that, i will make a guide to recover imei without a EFS backup, so please help me with the QCN. Best regards.
Click to expand...
Click to collapse
Hi, I have restored with QCN and edited now I have my IMEI and Baseband but the signal is 0 dbm 99 asu
I've tried to flash again the modem, change rom but nothing as changed... How do you have solved?
Yeah I haven't been able to get any service on my phone for awhile now it's been nothing but frustrating... Nothing I do seems to work I've on the verge of just throwing this phone against the wall a few times
Sent from my D6503 using XDA Free mobile app
No Wifi/networ/imei working
rombdeta said:
Okay, you are right, i understend. But QCN, is different, have a parameters of the network. Is only that i need, because i have repaired imxx, wifi, bluetooth, but in the radio signal i have 0 dbm 99 asu, because i haven't the radio band who is in the QCN, and the information on this. If i can repair that, i will make a guide to recover imei without a EFS backup, so please help me with the QCN. Best regards.
Click to expand...
Click to collapse
Hello,
Can you please help me with this.
My phone showing unknown baseband version.
Hello, guys i need your help here. My 2 week old Honor 8 was stolen by thief. Police retrieved the phone and I got it back. Problem is that the thief did something to the phone and tried to remove/replace IMEI and ROM so he wouldnt be tracked down by police, which obviously didnt help him. Now i got my phone back and there is writing " This phone is unlocked and cannot be trusted" everytime i reboot it, but it loads at least. I tried to flash the phone with Rollback and stock firmware from hihonor.com website but without luck. Flashing stops at 5% saying version mismatch or something like that.
2 more cents:
1. About phone shows 2 different IMEIs
2. Version number shows: FRD-C900B120
I would like my phone back to stock firmware without root or anything, i dont need that.
Can anyone help me out here? Thanks a lot!
Hi, i had your problem, stuck at 5% and here (in another thread) some people helped me, so i'm telling you what i did hoping i can help you too.
Update process:
First of all be sure to download the firmware updated (Marshmallow) http://download-c.huawei.com/download/downloadCenter?downloadId=92125&version=360419&siteCode=it-h
After the download is finished:
1. Make a backup, then format your External SD card from your PC (FAT32 should be fine)
1. Unzip (just extract) the update.zip and you should have "UPDATE.APP". Transfer this file to the SD card into the dload folder (if folder is not present, create it yourself). Pay attention, when i did this i haven't any file on the formatted sd card, so do this before transfer anything else
2. In the dialer app, enter the combination *#*#2846579#*#* and select "Software Upgrade" to make the updating process from SD start
3. If everything goes fine but the phone does not boot (bootloop on Honor logo), enter to recovery and wipe data and cache
I think that there is no need to use the rollback package as you weren't on a new software, so just download this firmware and you should be fine flashing it.
P.S The firmware i linked is for model FRD-L09, as i don't know where to find yours. If your phone is European version, then you can download and try to install it. After all, when the phone boots you can update to Nougat via OTA to B380 firmware if you want. Let me know if you succede
It did not help unfortunately. I downloaded the zip, extracted and moved dload with .app in it to formated SD card. dialed the number, selected the package, phone rebooted to twrp and nothing happend. so I turned it off and tried (+ - power button) install, it started installing but after 5% it says "Incompatibility with current version. Please download the correct package." and reboot system now. Same outcome as with rollbackers before
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120. thats all i got. btw I live in czech rep.
Aiwon said:
It did not help unfortunately. I downloaded the zip, extracted and moved dload with .app in it to formated SD card. dialed the number, selected the package, phone rebooted to twrp and nothing happend. so I turned it off and tried (+ - power button) install, it started installing but after 5% it says "Incompatibility with current version. Please download the correct package." and reboot system now. Same outcome as with rollbackers before
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120. thats all i got. btw I live in czech rep.
Click to expand...
Click to collapse
Okay, shouldn't have rebooted to twrp.. But if manually update fails maybe it's the case to try with the correct firmware. If you can find the firmware wich begins with FRD-L09C40 (wich belongs to Czech Republic) you can retry the update process. I searched around the web but found anything (maybe because i'm in italy, idk) but you can try to search in another thread here on xda. I saw a list of original firmware if i'm not wrong. You can try see there or ask them if they can provide a link for the correct firmware you need. Sorry if i can't help anymore
Aiwon said:
It did not help unfortunately. I downloaded the zip, extracted and moved dload with .app in it to formated SD card. dialed the number, selected the package, phone rebooted to twrp and nothing happend. so I turned it off and tried (+ - power button) install, it started installing but after 5% it says "Incompatibility with current version. Please download the correct package." and reboot system now. Same outcome as with rollbackers before
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120. thats all i got. btw I live in czech rep.
Click to expand...
Click to collapse
FRD-C900. Hmm I never saw anything like this before. Any thoughts @gopinaidu77?
Sent from my Honor 8 using XDA Labs
Aiwon said:
It did not help unfortunately. I downloaded the zip, extracted and moved dload with .app in it to formated SD card. dialed the number, selected the package, phone rebooted to twrp and nothing happend. so I turned it off and tried (+ - power button) install, it started installing but after 5% it says "Incompatibility with current version. Please download the correct package." and reboot system now. Same outcome as with rollbackers before
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120. thats all i got. btw I live in czech rep.
Click to expand...
Click to collapse
I can help bud . But before plz answer few of my questions.so that i can get a clear view if ur issue
If bootloader is unlocked, there should be no problem with flashing it via adb manually or TWRP.
If this fails, there is always a way how to fix it, with DC-Phoenix.
netvorCZEK said:
If bootloader is unlocked, there should be no problem with flashing it via adb manually or TWRP.
If this fails, there is always a way how to fix it, with DC-Phoenix.
Click to expand...
Click to collapse
Don't need DC anymore. Bootloader is already unlocked.
Sent from my Honor 8 using XDA Labs
gopinaidu77 said:
I can help bud . But before plz answer few of my questions.so that i can get a clear view if ur issue
Click to expand...
Click to collapse
sure, what would you like to know?
BL unlocked then flash through ADB.
Aiwon said:
Hello, guys i need your help here. My 2 week old Honor 8 was stolen by thief. Police retrieved the phone and I got it back. Problem is that the thief did something to the phone and tried to remove/replace IMEI and ROM so he wouldnt be tracked down by police, which obviously didnt help him. Now i got my phone back and there is writing " This phone is unlocked and cannot be trusted" everytime i reboot it, but it loads at least. I tried to flash the phone with Rollback and stock firmware from hihonor.com website but without luck. Flashing stops at 5% saying version mismatch or something like that.
2 more cents:
1. About phone shows 2 different IMEIs
2. Version number shows: FRD-C900B120
I would like my phone back to stock firmware without root or anything, i dont need that.
Can anyone help me out here? Thanks a lot!
Click to expand...
Click to collapse
Wow this is incredible . U can still retrieve your phone
gopinaidu77 said:
Wow this is incredible . U can still retrieve your phone
Click to expand...
Click to collapse
He was aking you bro what you would like to know.
Sent from my Honor 8 using XDA Labs
adriansticoid said:
He was aking you bro what you would like to know.
Click to expand...
Click to collapse
Plz a bit time
gopinaidu77 said:
Who ?
Click to expand...
Click to collapse
me?
i dont know what else to do, dunno how to flash it thru adb. No idea what my original version of the phone was/is
Aiwon said:
me?
i dont know what else to do, dunno how to flash it thru adb. No idea what my original version of the phone was/is
Click to expand...
Click to collapse
Can i know the phone model ?
gopinaidu77 said:
Can i know the phone model ?
Click to expand...
Click to collapse
Honor 8
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120
is this what you mean?
Aiwon said:
Honor 8
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120
is this what you mean?
Click to expand...
Click to collapse
Alright bro,it is what i mean . Can u access fastboot ?
Aiwon said:
Honor 8
dunno whats my correct version tbh, "About phone" shows under Model: FRD and under Version: FRD-C900B120
is this what you mean?
Click to expand...
Click to collapse
Plz reply can u access fastboot ? If u don't know u can say it no !! I will help u what so ever , but be frnly and no need to be shy!
gopinaidu77 said:
Alright bro,it is what i mean . Can u access fastboot ?
Plz reply can u access fastboot ? If u don't know u can say it no !! I will help u what so ever , but be frnly and no need to be shy!
Click to expand...
Click to collapse
yes i can im in fastboot&rescue mode connected to pc atm. display also says Phone unlocked
Aiwon said:
yes i can
Click to expand...
Click to collapse
Goodone bro .. give me two minutes . Can you wait ?plz
Aiwon said:
yes i can im in fastboot&rescue mode connected to pc atm. display also says Phone unlocked
Click to expand...
Click to collapse
Hi @Aiwon , plz download this.
After u had updated kindly report back i wil tell u what to do.
Kindly follow instructions as said , am pretty sure ur device works back.
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1278/g104/v62122/f1/full/update.zip
gopinaidu77 said:
Goodone bro .. give me two minutes . Can you wait ?plz
Hi @Aiwon , plz download this.
After u had updated kindly report back i wil tell u what to do.
Kindly follow instructions as said , am pretty sure ur device works back.
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1278/g104/v62122/f1/full/update.zip
Click to expand...
Click to collapse
Im sorry i cant download it, "page cannot be reached"
Hello guys, I'm so sorry for having to bug you all eventhough there already has been many threats regarding a bricked Honor 8.
But however, i'm really stuck because apparently my Honor 8 model is FRD-L19C636 B380 currently running emui 5.0
This phone was bought in Malaysia. Due to my retardness, i tried rooting this phone but accidently wiped the entire system with my backup of twrp.
This phone is unlocked, its having stock recovery now, phone works as in, there are many apps missing and theres no keyboard and camera does not work.
I seem to have downloaded the update.app for the latest version but it does not include CUST.IMG which then doesnt allow me to fully flash the rom.
When I'm thinking about downgrading, it didnt work either because i cannot find the correct version for the downgrade. (I randomly picked a FRD L19 emui 4.1 from the website and flash it, it failed at CUST.IMG and further bricked my device but now its back to the state where theres no keyboard and apps are missing)
Bootloader is unlocked
I can access fastboot and stock recovery. Please I really need help D: I would never want to mess with my phone ever again, my mom bought me this phone and it was hard for her, I feel really bad for not taking care of it properly.
Rommco05 said:
Hi, your build number is NRDtestkeys?
Click to expand...
Click to collapse
Im not sure what that is, but when i open "About Phone", it says Build NUmber : FRD-L19C636B380
Rommco05 said:
In settings u see update phone (updater) ?
Click to expand...
Click to collapse
No there isn't. Wow I didnt even realize that. At the bottom, theres only advanced settings and developer options and about phone
Is there anyway to fix this? D: I've tried so many ways already. I spent the entire day trying by downloading update.zips. But the internet service here in Malaysia really sucks. Down to 500kbps/s
Rommco05 said:
hm, what about factory reset in twrp? This can be a risk, but u have full build number anyway it is a risk because phone no must boot - or this can be a quick solution...
Click to expand...
Click to collapse
I've tried this before, the first time, it just factory reset then same. No keyboard , no apps. The 2nd time, "there is no OS do you really want to reboot?"
Is it possible to use a different region with FRD-L19?
Rommco05 said:
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1278/g104/v73884/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...ll/hw/spcseas/update_data_full_hw_spcseas.zip
---------- Post added at 16:06 ---------- Previous post was at 16:03 ----------
This is B360 classic update witch I flashed xx times (but I have C432) I think if u flash in twrp first region.zip and after update.zip, problem will done. Download this two zips and I wrote u steps after some moment
Click to expand...
Click to collapse
What is region.zip? U gave me 2 links
1) update.zip
2)Update data full hw
I guess I will have to flash twrp first
Rommco05 said:
Region is number 2)Update data full hw, I think u alredy have twrp, yes flash latest twrp
Click to expand...
Click to collapse
Okay, now i have twrp 3.1.1-1
Downloading those 2 links still
I did it! Thanks to you! Camera works, apps restored but the keyboard isnt there. What can i do
Edit: NVM I changed the keyboard it works now. OMG THANKS. Truly the KING OF HONOR
off topic did this FRD L19 supports Volte calling ?
Good to see members still helping out..
Operating make sure you do a full. Backup of your device and safe a copy on SD card or HH as well as you phone..
Rommco05 said:
It's ok, factory reset u do after install?
---------- Post added at 18:02 ---------- Previous post was at 17:58 ----------
You are new on xda I think, so if somebody help you or some post is for you helpful feel free to tap on thanks button, just for the future
Click to expand...
Click to collapse
Factory reset not needed
friends competes an honor 8 FRL-L19 did not do any procedure on it just downloaded an app in the play store called firmware finder and installed the stock rom 380 but my device went into loop it goes into the recovery mode already downloaded some roms and tried to install by the card but not always sure of the error ... Someone can help me
Hi! I have a Idol 3 (6045I variant) and everytime I try to restore to stock using Mobile Upgrade Q it gets to the part where it says "Searching the server for latest available software" then the phone turns on normally and it says "Download update software package failed. Please check your internet connection." and it does this on two computers that I have tried with two different upgrade Q versions. Could someone please help me identify the problem?
It seems Alcatel abandoned our device.
It seems Alcatel abandoned our device.
Ha, ha...
Look the reason you are getting the message is because you restored your phone once on IP 240.4.4.xx.x.xx.xx. If you use another IP address you would not get that message. So, use a vpn or change you IP or use someone else's internet connection. It has happened to me more then once and was very frustrating as until I figured it out. Go to google and type in "What is my IP address" and start their.
HEY OFF TOPIC but can you believe that XPOSED is finally released for Nougat!!!!
vq8acsxht said:
It seems Alcatel abandoned our device.
Ha, ha...
Look the reason you are getting the message is because you restored your phone once on IP 240.4.4.xx.x.xx.xx. If you use another IP address you would not get that message. So, use a vpn or change you IP or use someone else's internet connection. It has happened to me more then once and was very frustrating as until I figured it out. Go to google and type in "What is my IP address" and start their.
HEY OFF TOPIC but can you believe that XPOSED is finally released for Nougat!!!!
Click to expand...
Click to collapse
This doesn't seem to be the case because even after using a different internet connections and a vpn it still throws out an error message and after updating to a newer version of upgrade q it says "There is no greater version available to upgrade your phone" which doesn't make any sense.
chewyboy0 said:
This doesn't seem to be the case because even after using a different internet connections and a vpn it still throws out an error message and after updating to a newer version of upgrade q it says "There is no greater version available to upgrade your phone" which doesn't make any sense.
Click to expand...
Click to collapse
Good, it says "There is no greater version available to upgrade your phone" now do a factory reset of the phone. If you did not destory the recovery partition you should be good to go.
chewyboy0 said:
Hi! I have a Idol 3 (6045I variant) and everytime I try to restore to stock using Mobile Upgrade Q it gets to the part where it says "Searching the server for latest available software" then the phone turns on normally and it says "Download update software package failed. Please check your internet connection." and it does this on two computers that I have tried with two different upgrade Q versions. Could someone please help me identify the problem?
Click to expand...
Click to collapse
Use this program here ...
https://mega.nz/#!9UdDGJLI!9S87X0wH0OEc3nKSd7dZHCES7RpDW8iWpPnPSqCPLzs (I'm trying to think of how this goes by memory so bare with me)
make sure you have the drivers installed. extract the file and the password is in the txt file. I can't remember the exact steps, but I think it will do some type of update or you go to "get version" if you don't see 6045 in the device list. once it's there you can go to the grey box besides get version that says update or download or something. my brain heh I can't remember, but then you click that and it will bring you back to stock. I did it on my 6045O flawlessly. It brought me right into the latest update. also if you go into the program files and go to the Sugar software folder after it's downloading the latest firmware for your phone and you go to the bin folder you should see a downloaded folder with your model number plus some other numbers and letters. copy that to your desktop. once that's done find the file starting with "R" that is the recovery image. delete that and replace it with twrp recovery image and just name it recovery. go back into the main Sugar folder in the program files and replace the folder with your model number with that folder. you also see a folder named download. that is the downloaded firmware you can delete that folder and just leave the modded folder with your model number containing the twrp recovery image. meanwhile, go through the setup process on your phone and skip all the steps you can and go into the phone. go to the about device and tap on the build number to unlock the developer options. make sure the OEM bootloader unlock is toggled and I just changed the usb debugging also although I don't think that's necessary. go back into the Sugar program and then go to just the update or whatever it is beside the get version and click that and it will update the phone with the latest firmware and it will put the custom recovery on it. make sure once it's done downloading you unplug it and turn it off then go into recovery mode by holding the power down and volume up until the main logo comes up then let go of power and keep holding volume up until twrp boots up. make sure you already have the latest SuperSU zip on your sdcard. go to the terminal or sometimes one comes up from the beginning and enter the systemless supersu line/code or whatever you call it and then hit enter or if it will go straight into twrp first do a factory reset in the advanced wipe tab then the systemless supersu terminal line code and then install the supersu zip. that's it. your back to the latest firmware and rooted. oh and btw, I forgot if you have to be in download mode when you are using the Sugar program. I play around in several phones so forgot at the moment. If you need to go into download mode just plug in the usb as your holding power, volume up and down at the same time and then when it goes into the download mode screen hold volume up for 5-10 seconds until the screen goes black. I hope it helps and sorry if any of this is confusing. It can be a bit advanced for some.
Mobile Q doesnt work here too.
With or Without VPN cant download the update package :/
irinae said:
Mobile Q doesnt work here too.
With or Without VPN cant download the update package :/
Click to expand...
Click to collapse
Press and hold the Volume up button, then briefly press the Power button. Keep pressing the Volume up button. Scroll to the desired language using the Volume down button, then press the Power button. Scroll to wipe data/factory reset by pressing the Volume down button.
Then try to do an update OTA.
If you are running stock and have for the last 6 months or so, their are not any new updates???
Just curious why you would think their is an update??
Also, "There is no greater version available to upgrade your phone" chewyboy0 admitted that Mobile Q software does work because Mobile Q software had to go out to the Alcatel servers to check which version he had.
Finally, Also, you gave no reference of whether you are running stock ROM, Rooted?? TWRP?? or for that matter whether you Samsung Galaxy phone can be plugged into the Mobile Q software. In other words, your coming up a little short on details.
I am running a custom ROM and I wanted to go back to stock for various reasons but I will try one of the methods above.
Brian9285 said:
Use this program here ...
https://mega.nz/#!9UdDGJLI!9S87X0wH0OEc3nKSd7dZHCES7RpDW8iWpPnPSqCPLzs (I'm trying to think of how this goes by memory so bare with me)
make sure you have the drivers installed. extract the file and the password is in the txt file. I can't remember the exact steps, but I think it will do some type of update or you go to "get version" if you don't see 6045 in the device list. once it's there you can go to the grey box besides get version that says update or download or something. my brain heh I can't remember, but then you click that and it will bring you back to stock. I did it on my 6045O flawlessly. It brought me right into the latest update. also if you go into the program files and go to the Sugar software folder after it's downloading the latest firmware for your phone and you go to the bin folder you should see a downloaded folder with your model number plus some other numbers and letters. copy that to your desktop. once that's done find the file starting with "R" that is the recovery image. delete that and replace it with twrp recovery image and just name it recovery. go back into the main Sugar folder in the program files and replace the folder with your model number with that folder. you also see a folder named download. that is the downloaded firmware you can delete that folder and just leave the modded folder with your model number containing the twrp recovery image. meanwhile, go through the setup process on your phone and skip all the steps you can and go into the phone. go to the about device and tap on the build number to unlock the developer options. make sure the OEM bootloader unlock is toggled and I just changed the usb debugging also although I don't think that's necessary. go back into the Sugar program and then go to just the update or whatever it is beside the get version and click that and it will update the phone with the latest firmware and it will put the custom recovery on it. make sure once it's done downloading you unplug it and turn it off then go into recovery mode by holding the power down and volume up until the main logo comes up then let go of power and keep holding volume up until twrp boots up. make sure you already have the latest SuperSU zip on your sdcard. go to the terminal or sometimes one comes up from the beginning and enter the systemless supersu line/code or whatever you call it and then hit enter or if it will go straight into twrp first do a factory reset in the advanced wipe tab then the systemless supersu terminal line code and then install the supersu zip. that's it. your back to the latest firmware and rooted. oh and btw, I forgot if you have to be in download mode when you are using the Sugar program. I play around in several phones so forgot at the moment. If you need to go into download mode just plug in the usb as your holding power, volume up and down at the same time and then when it goes into the download mode screen hold volume up for 5-10 seconds until the screen goes black. I hope it helps and sorry if any of this is confusing. It can be a bit advanced for some.
Click to expand...
Click to collapse
Hey I think this is working its currently downloading at 27% I will let u know the progress. Thanks so much!!
chewyboy0 said:
Hey I think this is working its currently downloading at 27% I will let u know the progress. Thanks so much!!
Click to expand...
Click to collapse
This one work but it was way simplier to restore to factory default via the Mobile Q like before.
Bah i don't care anymore my 5.5 battery does strange things so i get a Xiaomi Mi5 from work to replace it.
I am from india, using 6045k, lost duel sim support duo to flashing of marionette's Rom. Still trying to get duel sim back, tried eluga firmware also, but unfortunately i didn't get any error at 45%. Now i am using flyos 2.0, its working like charm. But only one sim is there, i tried several software upgrader versions, but server is not connecting, its always stuck at 20%.
Pls help me.
Siraj Enriq said:
I am from india, using 6045k, lost duel sim support duo to flashing of marionette's Rom. Still trying to get duel sim back, tried eluga firmware also, but unfortunately i didn't get any error at 45%. Now i am using flyos 2.0, its working like charm. But only one sim is there, i tried several software upgrader versions, but server is not connecting, its always stuck at 20%.
Pls help me.
Click to expand...
Click to collapse
Currently Alcatel has disabled the posibility of reflashing a stock ROM with Mobile Upgrade Q, so the only way is by flashing via TWRP or Sahara tool.
I have a 6045Y in latest stock MM (Build 22) and i'm incapable of performing a flash with Mobile Upgrade Q in order to clean my modified /system, the worst thing is that there is no flashable zip of this version which contain many critical fixes. I'm too very annoyed with this change of policy of Alcatel/TCL, they want me to buy a new smatphone but I'll not give them that pleasure, the Idol 3 5.5 is the best smartphone i've ever had in terms of hardware, it's a shame...
ciclolars said:
Currently Alcatel has disabled the posibility of reflashing a stock ROM with Mobile Upgrade Q, so the only way is by flashing via TWRP or Sahara tool.
I have a 6045Y in latest stock MM (Build 22) and i'm incapable of performing a flash with Mobile Upgrade Q in order to clean my modified /system, the worst thing is that there is no flashable zip of this version which contain many critical fixes. I'm too very annoyed with this change of policy of Alcatel/TCL, they want me to buy a new smatphone but I'll not give them that pleasure, the Idol 3 5.5 is the best smartphone i've ever had in terms of hardware, it's a shame...
Click to expand...
Click to collapse
Did u tried sugar mtk tool??
Siraj Enriq said:
Did u tried sugar mtk tool??
Click to expand...
Click to collapse
No, could you share the link? Thanks in advance.
ciclolars said:
No, could you share the link? Thanks in advance.
Click to expand...
Click to collapse
Thank god, today I got my phone to stock rom, by using q5.1.8.
Actually, yesterday only i heard about q.5.1.8, its been a year that i was trying to do this. Appart from q5.1.8, i connected VPN to U. S. Now everything is fine.
I dont know which one helped me, that the q5.1.8 or the VPN. :laugh:
Thanks to all.
Siraj Enriq said:
Thank god, today I got my phone to stock rom, by using q5.1.8.
Actually, yesterday only i heard about q.5.1.8, its been a year that i was trying to do this. Appart from q5.1.8, i connected VPN to U. S. Now everything is fine.
I dont know which one helped me, that the q5.1.8 or the VPN. [emoji23]
Thanks to all.
Click to expand...
Click to collapse
How exactly did you managed to do it? Is it possible to reflash the stock ROM?
ciclolars said:
How exactly did you managed to do it? Is it possible to reflash the stock ROM?
Click to expand...
Click to collapse
Actually, software upgrader can do the job. But the problem was slow server speed. Use q. 5.1.8, simply connect your in switch off condition, and try upgrading, if its not working, try VPN. I tried psyphon VPN connected to USA. In india serveris very slow.
6045k still running on lilopop, thats why people go going for stock roms.
Siraj Enriq said:
Actually, software upgrader can do the job. But the problem was slow server speed. Use q. 5.1.8, simply connect your in switch off condition, and try upgrading, if its not working, try VPN. I tried psyphon VPN connected to USA. In india serveris very slow.
6045k still running on lilopop, thats why people go going for stock roms.
Click to expand...
Click to collapse
In my case, Mobile Upgrade Q display a message that says I'm currently in the latest software version so it doesn't allow me to reflash stock ROM. My device is a 6045Y build 22 MM.
ciclolars said:
In my case, Mobile Upgrade Q display a message that says I'm currently in the latest software version so it doesn't allow me to reflash stock ROM. My device is a 6045Y build 22 MM.
Click to expand...
Click to collapse
Try Sugar Mtk tool
https://mega.nz/#!9UdDGJLI!9S87X0wH0...8iWpPnPSqCPLzs
Details is there on this thread.
I never tried it, try it. Read above msg by member Brian9285
FIX WIFI not connecting/ MAC ADDRESS 02:00:00:00:00:00 / bluetooth / calibration sensor / drivers missing from phone/ wlan mac and ip unavailable..
There is the FIX:
1. Download your stock firmware android
2. Flash OrangeFox recovery for your phone
3. In your stock firmware folder find file persist.img
4. Put persist.img in your phone and flash it with OrangeFox recovery..image option not zip..check persist-image option and flash it
5. Restart your phone
That's it, enjoy your fix
thank you, buddy, you really saved me you are a fkn hero
fawzy ahmed said:
thank you, buddy, you really saved me you are a fkn hero
Click to expand...
Click to collapse
I'm glad i could help you :good:
i tried on mine ( xiaomi mi 8 ) didn't help
malesh said:
FIX WIFI not connecting/ MAC ADDRESS 02:00:00:00:00:00 / bluetooth / calibration sensor / drivers missing from phone/ wlan mac and ip unavailable..
There is the FIX:
1. Download your stock firmware android
2. Flash OrangeFox recovery for your phone
3. In your stock firmware folder find file persist.img
4. Put persist.img in your phone and flash it with OrangeFox recovery..image option not zip..check persist-image option and flash it
5. Restart your phone
That's it, enjoy your fix
Click to expand...
Click to collapse
the problem is, i cannot find any persist.img in the firmware folder i installed (50.1.A.4.76_R1A)
malesh said:
FIX WIFI not connecting/ MAC ADDRESS 02:00:00:00:00:00 / bluetooth / calibration sensor / drivers missing from phone/ wlan mac and ip unavailable..
There is the FIX:
1. Download your stock firmware android
2. Flash OrangeFox recovery for your phone
3. In your stock firmware folder find file persist.img
4. Put persist.img in your phone and flash it with OrangeFox recovery..image option not zip..check persist-image option and flash it
5. Restart your phone
That's it, enjoy your fix
Click to expand...
Click to collapse
didn't help bro, i used twrp recovery to flash persist img
Chouiyekh said:
didn't help bro, i used twrp recovery to flash persist img
Click to expand...
Click to collapse
and you found persist.img just in the folder of the firmware, or on the phone, after you flashed it, ot where?
layalala said:
and you found persist.img just in the folder of the firmware, or on the phone, after you flashed it, ot where?
Click to expand...
Click to collapse
I'll tell what i did, i downloaded the last global version and flash it to phone using miflash tool, then i flash twrp and take persist.img from the firmware ( last global version) and put it on phone memory, then flash it using twrp, but the problem still exist
Chouiyekh said:
I'll tell what i did, i downloaded the last global version and flash it to phone using miflash tool, then i flash twrp and take persist.img from the firmware ( last global version) and put it on phone memory, then flash it using twrp, but the problem still exist
Click to expand...
Click to collapse
ok, i don't even found persist.img
try that, i will try that later
https://forum.xda-developers.com/showpost.php?p=79378001&postcount=121
layalala said:
ok, i don't even found persist.img
try that, i will try that later
https://forum.xda-developers.com/showpost.php?p=79378001&postcount=121
Click to expand...
Click to collapse
It will definitely be safer to post your issue on your device forum
These generic 'fixes' will not work for every phone and may even result in your phone being soft bricked or hard bricked.
what does soft bricked and hard bricked mean, please ?
https://shareit.onl/ https://mxplayer.pro/
beyonslay said:
what does soft bricked and hard bricked mean, please ?
Click to expand...
Click to collapse
Where your phone becomes:
1. Useless due to software issues = soft brick but can be fixed
2. Useless due to major hardware failure = hard brick and very difficult to fix or completely dead
The term "brick" is exactly as you'd think - literally like stone
hello,
These two are the most vulnerable things that can happen to an android device.
SOFT-BRICKING:
When your fone gets soft-bricked, it means that the operating system you were going to install has not been installed properly.
Some of the reasons may be :
1. ROM not compatible with your device.
2. Phones battery going down in the middle of a OTA or normal update
3. ROM not properly installed in your device.
The most common things one can observe in a soft bricked fone is BOOT-LOOP
it means your fone boots up, and gets stuck in booting mode.
Assume you own a SONY device , if your fone is stuck in boot loop then, the SONY logo will show up on the screen for some time and the the fone will automatically turn off and after some time it will turn on again repeating the same process.
HARD-BRICKING:
It generally means all the data in your fone is wiped out. This just dosent mean the operating system but also the system used to load the operating system, also called as recovery. Therefore, you will have no way to install your custom OS or ROM. This generally happens when you try flasing ROMS in a mobile device that has a weak recovery system.
One of my friends tried to flash custom ROM in Yu-Yureka and ended up hard-bricking the fone.
If you softbrick a mobile device, you can have the liberty of using softwares like flashing tools to install ROMs and Recoverys and make your fone work.
If you ended up hard-bricking your device, the mobile even wont respond to any physical holding or tapping of the buttons on your phone and all that can be done is getting a good fast wifi connection to do a strong research for your next mobile.
i hope this is helpful for you.
Chouiyekh said:
i tried on mine ( xiaomi mi 8 ) didn't help
Click to expand...
Click to collapse
I have same problem like you.
If you solved it, can you tell me how?
Anyone ever solve this ?
malesh said:
FIX WIFI not connecting/ MAC ADDRESS 02:00:00:00:00:00 / bluetooth / calibration sensor / drivers missing from phone/ wlan mac and ip unavailable..
There is the FIX:
1. Download your stock firmware android
2. Flash OrangeFox recovery for your phone
3. In your stock firmware folder find file persist.img
4. Put persist.img in your phone and flash it with OrangeFox recovery..image option not zip..check persist-image option and flash it
5. Restart your phone
That's it, enjoy your fix
Click to expand...
Click to collapse
I tried this way, but I can't fix it.
greeneyez15o said:
Anyone ever solve this ?
[/QUO
Click to expand...
Click to collapse
I was having this problem for at least 1 month. Tried everything that is posted in xda forums. Gave up and was using cellular connection, Until I found your post and gave it a shot. Now, my wifi is back to normal , Many thanks to you. You are truly a lifesaver.
I also tried this method before, but it didn't work. Before I was using TWRP recovery. But after flashing with OrangeFox my wifi was fixed.
Edit MAC
Hello! I have a Lenovo Xiaoxin Pad M10 Plus but wifi is not turning on.
There's no MAC address on the wifi interface, but bluetooth is working.
I flashed the original ZUI_13.5.365_ST_220526, TWRP and Magisk.
I'm trying to find a way to hardcode a new MAC address to the wifi card.
Or maybe the persist or modem partitions were bricked by the previous owner?
I was thinking if I flash these partitions from a working device I can get the wifi to work again?
Can someone help me please. Thanks!